User Manual(Download) - ampelos
Contents
1. 5 Installation TSRK 1000P TSRK 1000P AC power code connection VAN Do not touch AC power code with wet hands danger for electric shock CAUTION AN Socket for AC power code should be grounded Danger for electric shock and fire hazard WARNING without earthing USB connector of product body for use VGA out connector RS232C Interface connector 9 TITTET Contact to sales agent regarding connection of each output input NOTE method TSRK 1000P 6 Measurement E Turn on the power switch E Adjust the height of the instrument table to make the patient comfortable m Roughly match the patient s eye height with the chin rest up down buttons Ensure the examinee has not placed the hand or fingers under the VAN chin rest if not the hand or fingers may be hurt Wipe the chin rest and the head rest with ethanol to disinfect it each CAUTION time a different examinee uses it Manual start mi Adjust the position and focus the patient s eye E Please make a request to look at the picture comfortably and tranquilly during optometry VAN Do not place the hand or fingers between the stage and base if not the hand or fingers may be hurt CAUTION E Press the measurement button Measured data are displayed in the monitor screen E If you are not satisfied with the measured value measure again in the same2. AXIS TSRK 1000 P Ophthalmic Ref Keratometer Operation Manual sciencetera Co LTD REVISION 1 11E Contents Intended Use Import Notice Environmental Factors Safety Information EMC 1 General Description 1 2 Features 3 Notes for Using the Instrument 2 4 Description of Parts 4 5 Installation 6 6 Measurement 8 Manual start Auto start 9 Detailed flow chart for the measurement modes 10 Measuring process Massages given during the measurement 11 6 1 Simultaneous Keratometry and Refractometry Mode K R mode 12 6 2 Refractometry Mode REF mode 6 3 Keratometry Mode KER mode 6 4 Contact Lens Base Curve Measurement Mode CLBC mode 13 7 Printed data 13 8 Other modes 14 Measurement in IOL Mode Intraocular Lens Measurement Measurement in Size Mode Cornea Diameter Size Measurement 15 Measurement in Ret ILLUM Mode Retro Illumination Measurement 16 Display Mode Display Measured data 18 9 User Setup 19 10 Inspection and Maintenance 22 11 Standard parts 25 12 Specifications 26 WARRANTY Intended Use Important Notice Environmental Factors TSRK 1000P TSRK 1000P is the instrument to measure the refracting power of eye and the radius of curvature of cornea This instrument images the special pattern in retina and captures the image reflected in retina cornea an
3. 404 1st Innoplex B D 371 47 Gasan Dong Geumcheon gu Seoul Korea 153 803 Tel 82 2 6679 0120 0122 Fax 82 2 6679 0123 E mail city cityopt com TSRK 1000P SERVICE INFORMATION 1 Repair O If problem cannot solved even after taking the measures indicated in section 10 contact Terascience representative or distributor for repair Please refer to the name plate and let us have the following information Name of the instrument TSRK 1000P Serial Number 9 digit characters indicated on the name plate Phenomenon In detail MODEL TSRK 1000P NPUT 100 240 V 50 60Hz 100VA AN Ophthalmic Ref Keratometer HIGE RE SN li Need to acquire operation manual thil Manufactured by sciencetera Co Ltd 404 ist Innoplex B D 371 47 Gasan Dong Geumcheon gu Seoul Korea 153 803 Tel 82 2 6679 0120 0121 Fax 82 2 6679 0123 EU Representative Argus individuell optic GmbH Oedenstockacher Str 11 0 85640 Putzbrunn Germany MADE IN KOREA 2 Limit for supplying performance parts for repair E Performance parts required to maintain the functioning of the product of this product will be stocked for eight years after discontinuation of product to allow for repair 3 Disposal of the instrument A CAUTION This instrument incorporates a lithium battery which may pollute the environment if the instrument is abandoned Please ask a professional waste dispo
4. s eyes with reference RET ILLUM mode page 14 If you checked move the focus to the position with no problem and measure 12 TSRK 1000P 6 4 Contact Lens Base Curve Measurement Mode CLBC mode E Press MODE button until CLBC mark appears on the monitor screen m Attach contact lens to the holder Fill water in the concave part of contact lens holder and attach contact lens to the holder with the concave side upward Take care that the contact lens is not inclined and bubbles are not allowed in m Attach the contact lens holder to the chin rest Remove the chin rest paper Insert the contact lens holder into the chinrest pins to place the contact lens to face the measurement window m Perform measurement following the measuring process m f you want print the measured data press print button 7 Printed Data TSRK 1000P KER DATA Keractometry Data Date amp Time 2007 01 01 AM 00 00 Index 1 3375 Index to be applied Patient Name NAME lt R gt RI R2 Right Eye mark 7 85 7 81 Refractometry Data REF DATA 7 84 7 81 3 measured data of the right eye Vertex Distance Cylindrical Form VD 12 00 CL 7 86 7 82 AVE 7 85 Averaged data of the right eye Right Eye mark lt R gt SPH CYL AX CYL 0 25 Corneal Cylinder Diopter 0 25 0 00 3 measured data of the right eye 0 00 0 00 lt L gt RI R2 Left Eye mark I IOL mode applied I 0 00 0 00 7 75 7 70 Averaged data of the ri
5. injury Never disassemble or modify this instrument because it may result in fire or electric shock Also since this instrument incorporates high voltage parts and other hazardous parts touching them may cause death or serious injury Should any of the following occur immediately turn OFF the power switch unplug the power cable from the AC outlet and contact the dealer or agent who where you purchase this instrument When there smoke strange odor or abnormal sound When liquid has been spilled into the instrument or metal object has entered through an opening When the product has been dropped or its housing damaged A WARNING Do not touch signal input signal output or other connectors and the patient simultaneously CAUTION This instrument is shipped with a grounding type power cable To reduce the risk of electric shock always plug the cable into a grounded power outlet CAUTION Ensure that the examinee has not placed his her hand and fingers under the Chin rest Otherwise hand or fingers may be hurt Z CAUTION Wipe the forehead rest with ethanol or glutaraldehyde solution to disinfect it each time a different examinee uses it in order to prevent infection CAUTION Change the chin rest paper each time the examinee changes in order to keep the chin rest clean Z CAUTION Do not place your hand or fingers between the stage and base Also ensure that the examine
6. not give the shock or drop the instrument If the instrument receives a strong shock the function of this instrument may be damaged Handle with care E Do not use this instrument in the sunlight or bright indoor light the bright lights can influence the results of measurements E Do not use chemical solutions such as thinner alcohol benzene etc for cleaning the dirt on the case It may damage the instrument E In the case of sudden heating of the room in cold areas wait until the thermal shock disappears before measurement E Consult the dealer to connect this instrument with other equipment E Keep the optical parts of the examinee side clean A fingerprint or other substances on the optical parts may cause an error or inaccurate results E f there is noise smoke or strange odors while working disconnect the power supply and consult the dealer E In moving this instrument fix the stage with the clamping bolt after remove power code and then lift the bottom of this instrument with both hands E When you do not use this instrument for a long period turn off the power and take the dust off from cover on this instrument E Before the other instrument is connected to this instrument in RS282c port please check that the instrument to be connected has the safety certification marks If not the function of this instrument may be damaged TSRK 1000P 3 Notes for Using the Instrument E This device has be
7. the cursor eE E Clear the image to be selected E REAL SIZE E DOUBLE SIZE ESC DISP DOUBLE SIZE NEXT DISP REAL SIZE NEXT CLR hey Button to magnify the selected image to double size Button to magnify the selected image to real size INT Move the cursor INT v am Move the cursor 17 Display Mode Display Measured data TSRK 1000P The stored data in memory can be displayed up to 10 data for each eye in this mode DISPLAY MODE REF 1 LEFT i 130 Essi at PD___61 MME 1 3375 DISPLAY MODE CLBC 3 na 7 80 7 80 ESC NEXT G R EJ Press EEA button in the measurement mode to enter the display mode and the measured refractometry EI Press button in the display mode to display the refractometry data The page will be changed to the 2nd page and the measured keratometry data will be displayed El Press button in the display mode to display the keratometry data The page will be changed to the 3rd page and the measured CLBC contact lens base curve data will be displayed H Press button in the display mode to display the CLBC data The page will be changed to the 1st page again B If you want to clear all the measured data press button If you want to change the set up data press SETUP button Setup mode will be explained in the Cp 9 Note SET UP button is hidden as the 5th button E Press button in any page of the display m
8. way TSRK 1000P Auto Start M Press the button under the monitor screen to measure automatically then Manual sign VR to be displayed in the upper side of the monitor screen will be changed to AUTO sign FAQ m Adjust the position and focus the patient s eye with the operation stick As soon as the patient s eye is aligned properly measurement starts automatically M lf you want manual start again press button under the monitor screen one more time Auto start and Manual start are toggled by the button m Adjusting the patient s eye to the instrument BM During the adjustment of the position and focus the patient s eye the alignment marks are displayed on the monitor screen m Place the center mark in the center of the collimating box Right and left slide the operation stick right or left Back and forth slide the operation stick back or forth Vertical turn the operation stick BM Adjust so that the Alignment mark is appeared M Press the measurement button Pupil distance Patient s number Auto Manual sign Aiming Spot NGS Er no PAPER PD 85 NO 000 fM Alignment mark Collimating box EEE SO i Vertex distance measurements E JC DA Gylinder Type MODE A Mx _ 10L ILUM SIZE _DISP Button signs TSRK 1000P Detailed flow chart for the measurement modes Press IOL button Press IL Mode button Press ILUM button TT AU
9. Press Mode button hr za ken ken SIZE button fr Mode button a Press DISP button fara Press I Press Measuring process m Make sure that the instrument is in the mode to be wanted If not press mode button until the mode to be wanted appears on the monitor screen m Perform focusing and alignment using the operation stick m When the CEN and FOC Signs are displayed OK on the monitor screen press measurement button If in auto start mode measurement is performed automatically without pressing measurement button m After measuring an eye 3 times the alignment mark will disappear If you want more measurement press measurement button BM Slide the instrument towards the other eye and the alignment mark will appear again E Measure the other eye in the same manner M After measuring press print button and the measured data are printed out 10 TSRK 1000P Messages given during the measurement Refractometry 0ver Spherical power exceeds 25D OVER Spherical power exceeds 22D C OUT Cylindrical power exceeds 10D Keratometry OvER Radius of curvature exceeds 10mm OVER Radius of curvature exceeds 5mm C OUT Astigmatism exceeds 10D TRYAGAIN During the measurement target eye moves There is s different value by 5D or more over the previous measurement Alignment is not proper Refractometry is too dark with intraocula lens etc In this case change the mod
10. ars again and again consult the dealer Message System Error EEPROM Data Error EEPROM Error Motor Error Printer Error Cause Internal error Remedy Turn OFF the power switch and turn on again after 10 seconds OVER Sphere of eye is over 22D Radius of curvature is over 10mm SOVER Sphere of eye is over 25D Impossible to measure Radius of curvature is over 5mm C OUT Astigmatism is over 10D Corneal astigmatism is over 15D See Messages given TRY AGAIN Alignment is not proper during the measurement in section 6 NO PAPER No printer paper Load printer paper 22 TSRK 1000P Replacement of printer paper S5 SN SN 7 3 lt to 5 D 3 2 5 D Q Fuse exchange AC Power Code must be disconnected during exchange of fuse AN Do not connect AC Power Code to power source without Fuse Holder Danger for electric shock WARNING Use provided fuse 250V 2A for exchange Use standard Fuse to avoid danger of fire hazard in case of product trouble 23 TSRK 1000 Daily checkup The instrument is least resistant to dust Turn off power supplyand cover the instrument with the attached cover when it is not in use Do not give any heave shock to the instrument The examination window is the most important Use good care not to contaminat the window with fingerprints of get dirty If the room is quic
11. asurement mode E Control operation stick to align the pupil in the two EI Press the measurement button to freeze the window El Press button to select the bar you want to move El Press TE button or button to move the selected bar The measured value will be displayed on the monitor screen El Press button to select the other bar you want Press button or button to move the selected bar The measured value will be displayed on the monitor screen E Press Measurement button and freezed window is released and 2 will be selected El Repeat procedures 2 7 Slide the stage with the operation stick to the other side and measure the other eye in the same way E Press PRINT button and the result of cornea diameter will be printed as the item of lt CORNEA SIZE gt ci Pe Exit Size Mode Button Pal Button to select the 1st or 2ed LE Measurement Right Side Eye N of Pupil Size Jaa Press measurement H Measurement M sign FTP Button to select the bar e Button to move the button e Sia to left sid Button to move the button pA Nilai to right side Perm Clear Button 15 TSRK 1000P Measurement in Ret ILLUM Mode Retro Illumination Measurement You can observe the condition of scratch or cataract on the eye on the monitor in this mode Press button in the measurement mode Ask the examinee to look at the red spot of the eye fixation target Adjust th
12. ccording National Code Potential Electromagnetic or other Interference Do not use this product in strong Magnetic fields such as near motor Do not place heavy objects on the case or block the ventilation holes General Safety Information If you see any warnings or cautions printed on the warning labels follow the safety instruction in this manual Ignoring such cautions or warnings while handling the product may result in injury or accident Be sure to read and fully understand the manual before using this product Keep this manual in easy to access place TSRK 1000P CAUTION SIGN DISCRIPTION Z WARNING This indicates a potentially hazardous situation which could results in death or serious injury to you or others A CAUTION This indicates hazardous situation which may result in minor injury to you or others or may result in machine damage NOTE This is used to emphasize essential information Be sure to read this information to avoid incorrect operation CAUTION SIGN DISCRIPTION A WARNING WARNING A WARNING Z WARNING Only operate the instrument with the power supply indicated on the rate plate Otherwise it may result in fire or electric shock Be sure to turn OFF the power switch before connecting or disconnecting the cables Also do not handle them with wet hands Otherwise you may get an electric shock that may result in death or serious
13. d crystalline lens with CCD camera Please use Ophthalmic Ref keratometer after you read the manual carefully It is not allowed to add the any factors which will be caused machine problems The device complies with ISO 10342 and ISO 10343 The dioptric powers are indicated with reference wave length Ad 880nm This manual contains information necessary for correct and effective operation of Ophthalmic Ref keratometer and provides specifications and procedures for operation and maintenance Please keep this manual and read it whenever necessary Please do not use at hot and humid place Normal operation temperature range is from 10 to 40 C and humidity is from 30 to 75 Do not use chemical detergents for cleaning the dirt on the case Do not give the shock and open the case without any purpose TSRK 1000P Safety Information Accessory equipment connected to the analog and digital interfaces must be certificated according to the respective IEC standards e g 1EC 950 for data processing equipment and IEC 601 1 for medical equipment Furthermore all configuration shall comply with the system standard EN 60601 1 1 1993 Everybody who connects additional equipment to the signal input part or signal output part which configures a medical system and is therefore responsible that the system complies with the requirements of the system standard IEC 601 1 1 1993 When in doubt you are recommended to cons
14. e to the IOL mode Pupil diameter is less than 2 0mm In this case measurement is impossible basically but sometimes more correct alignment makes the measurement possible ERROR During the measurement the patient blinks or something may be wrong If this massage appears when proper measurement is performed with the model eye contact the service man 11 TSRK 1000P 6 1 Simultaneous Keratometry and Refractometry Mode K R mode E Press I MODE button until K R mark appears on the monitor screen m Perform measurement following the measuring process BM Inthis mode Keratometry is automatically performed before refractometry m If you want print the measured data press print button 6 2 Refractometry Mode REF mode m Press TAI button until REF mark appears on the monitor screen m Perform measurement following the measuring process BM In this mode you can perform only refractometry m If you want print the measured data press print button 6 3 Keratometry Mode KER mode E Press MODE button until KER mark appears on the monitor screen m Perform measurement following the measuring process E In this mode you can perform only keratometry M f you want print the measured data press print button You would be hard to get the measured value of REF if a patient has some disease concerned with his her eyes NOTE In that case you should check the condition of patient
15. e amount of light of each light source REF ILM TAG for the fine image DI Amount of light E atient number Light source Light for retro illumination Light for eye front Right left eye G SUB number Measurement sign 4 Mode sign CAPTURE REF J JOL I 33e ESC button to go out this mode Button to change the capturing mode Button to display the captured images Jala ef Select light source E ps es Button to change the amount of light CAPTURE ESC MODE DISP SHIFT 1 Button to change the amount of light only capture CAPTURE REF capture amp measure capture amp measure 10L M Press measurement button and the image is captured m Press measurement button again and the image is stored into memory M Press other button and the image is unfrozent Time Patient amp Sub number Measured data Right left eye Press measurement button SAVE Press measurement button to save the image into memory Press Other button CANCEL Press other button to unfreeze Press measurement button SAVE Press Other button CANCEL 16 TSRK 1000P E Press BESTS button in retro illumination display Images in memory will be displayed ESC Escape 2AE Button to magnify the selected image to real size REAL SIZE NEXT V Button to move
16. e does not place his her hand or fingers there either Otherwise hand or fingers may be hurt TSRK 1000P 1 General Description AXIS Ophthalmic Ref keratometer consists of Main body Model eye Printer paper Power cable Dust cover Operation manual and Fuse Mainbody 1 Modeleye 1 Printer paper 2 Rolls Power cable 1 Dust cover ______ _ 1 Fuse 2 Operation manual 1 2 Features E Various Measurements Supported Not only refractometry and keratometry but also base cave of contact lens and corneal diameter can be measured with this instrument E Wide measurement range Because TSRK 1000P covers from 25D to 22D in refractometry and from R5mm to R10mm in keratometry almost of all examinee can be measured E Accurate measurement With the foggy method of eye fixation target making the eye comfortable you can measure more accurately E Auto Starting Function As soon as AXIS Ophthalmic Ref keratometer is properly aligned to each eye this function initiates the measurement process and generates the measurement results automatically E High Resolution Color LCD Monitor High Resolution Color LCD Monitor 0 3 Mega Pixel 6 4 inches Color TFT LCD Provides Fine and Large Iris Image with color alignment marks M Other measurements IOL Pupil diameter Ret illum TSRK 1000P 3 Notes for Using the Instrument E Do
17. en tested and found to comply with the limits for medical devices to the IEC 60601 1 2 2001 am1 2004 and Medical Device Directive 93 42 EEC These limits are designed to provide reasonable protection against harmful interference in a standard medical installation This device generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to other devices in the vicinity However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to other devices which can be determined by turning the device off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving device Increase the separation between the devices Connect the device to an outlet on a circuit different from that to which the other device s are connected Consult the manufacturer or field service technician for help 4 Description of Parts TSRK 1000P a il HY TIT Il 5 I sl RA i ooo 6 ea D 8 9 10 EI Monitor screen to displays measurement results TSRK 1000P Operation Buttons
18. ght eye AVE 0 00 0 00 7 74 7 69 122 3 measured data of the left eye Left Eye mark lt L gt SPH CYL AX 7 76 7 71 122 1 25 0 50 35 AVE 7 75 7 70 121 Averaged data of the left eye 3 measured data of the left eye 1 25 0 50 37 CYL 1 00 Corneal Cylinder Diopter 1 50 0 25 33 Averaged data of the left eye AVE 1 25 0 50 36 PD 63mm Pupil Distance SCIENCETERA CO LTD 13 TSRK 1000P 8 Other modes Measurement in IOL Mode Intraocular Lens Measurement When errors easily occur in measurement of an eye with IOL unclear crystal lens or small pupil etc the measurement may be possible by pressing IOL switch Measurement process in the IOL mode is following M Makes measurement following the measuring process to be mentioned in chapter 6 measurement m f errors easily occur in measurement of an eye or low confidence level mark is displayed on the monitor screen with measurement results Press button and mark will appear under mode sign on the monitor screen M Make a measurement 000 68 SETAE x Right Left Eye enor Number of Sphere Cylinder Axis Vertex distance measurements BE JC JA Cylinder Type MODE A M _10L ILUM SIZE _DISP Button signs i Collimating box GO 14 TSRK 1000P Measurement in Size Mode Cornea Diameter Size Measurement BM Inthis mode diameter of cornea can be measured for prescribing contact lens El Press the I SIZE button in the me
19. kly heated in winter or in a cold region the instrument lenses may get cloudy Take time before starting measuring till the lenses get clear naturally Cleaning the instrument BM Dust has got on the examination window Use a blower to blow off dust E Fingerprints of oil has got on the examination window Use a blower to blow off dust and a clean gauze with a little camera lens cleaner to lightly wipe off BM When the instrument cover has got dirty Use the attached silicon cloth or a dry soft cloth to wipe off Do not use benzine thinner of a chemical contained dustcloth 24 11 Standard parts TSRK 1000P Power cable 1EA SCIENCETERA Dust cover 1EA Printer paper 2EA Model eye 1EA Operation Manual 1EA 25 TSRK 1000P 12 Specifications Refractometer mode n Sphere 25D 4220 O iii Cylinder 0 410D Axis _1 180 Keratometer mode Ret ilum OK Environmental Requirements Operation temperature 10 to 40C Automospheric pressure 700hpa to 1060hpa Others Measuring start Auto Manual 26 TSRK 1000P WARRANTY sciencetera Co Ltd warrant this product against defects in materials and Workmanship for a period of ONE 1 YEAR from the date of original retail purchase Purchase Information Model Number TSRK 1000P Serial Number Purchase Date Sciencetera Co Ltd
20. ode to go out this mode 18 TSRK 1000P 9 User Setup You can change all the settings about measurements printouts etc in this set up mode Press DISP button in measurement mode and enter the display mode Press Set up button Hidden button of the 5th button and How to change the page Press button How to change the item Press button How to select the item Press button How to change the contents Press A V button Chin rest up down button How to save data Press button How to enter the measurement mode Press button 1st page Displaying amp printing format 1 Page No on for PP 00 YMD fo mov PJ omy __ 2006 01 01 PM6 40 Fo on for PP ALL DATA AVERAGE OFF JO ALL DATA AVERAGE JJ OFF JO KONI Patient s No on off NOME Patient s No Eye image print on off REF KER RIGHT AUTO MANUAI AUTO COUNT CLR b utton is used to sor Lui in Auto NOTE _ initialize the patient s start mode number only 2 000000 x ES Gaja NEXT CHANGE SHIFT mGLRon mSAVE Store the edited data 19 TSRK 1000P 2nd page Displaying amp printing format 2 SETUP M Page No HITEN EE Vertex distance __0 125 Mi 0250 Cylinder type uo foot Increment of sphere amp cylinder EE UD i 30 Increment of diopter Ker 115200 f Displaying form of keratometry Pas EEE RS 232C Speed PRINT am
21. p RS 232 Applied index Ker ae FE MODE Measurement mode order REF KER ESC NEXT CHANGE SHIFT CLR SAVE 3rd page Message for internal printer SETUP MODE eg Page No PRINTER LABEL TERASCIRNCE COnTTD gt Move editing cursor 82 31 603 6043 EJ Move editing cursor DaS Delete character MEN Edit character B NNE chinrest up down button 20 TSRK 1000P 4th page Correction of measured data Page No Sphere correction D 0 400 Cylinder correction D 0 250 Angle correction degree REF DSTA f 0 000 Sphere correction mm KER DSTS 0 050 Cylinder correction mm 0 040 i H Angle correction degree Button to Change the COU contents of selected item ESC NEXT CHANGE COUNT COUNT SAVE 5th page Display SETUP MODE 5 Page No DISPLAY i LCD LIGHT Oniy LCD LIGHT LCD LIGHT _99 TEHES N Oniy BRIGHTNESS BRIGHTNESS CONTRAST 50 CONSE Oniy CONTRAST GAMMA 0 45 GAMMA Oniy GAMMA ESC NEXT CHANGE COUNT COUNT SAVE 21 10 Inspection and Maintenance TSRK 1000P Before Calling a Service man Warning messages will be displayed on the monitor if some problems occur It might be operation errors or problems of the machine In this case refer the following instructions If the function is still not salvaged or recovered Please disconnect the power supply and consult the dealer If the message appe
22. r than domestic and those directly connected EN 61000 3 2 to the public low voltage power supply network that supplies buildings used for domestic purposes Voltage fluctuations 2 Flicker emissions EN 61000 3 3 1 For the regions where the rated voltage is 230V or greater this instrument complies with class A For the regions where the rated voltage is less than 230V this standard is not applicable 2 For the regions where the rated voltage is 230V or greater this instrument complies with this standard For the regions where the rated voltage is less than 230V this standard is not applicable TSRK 1000P EMC Eelctromagnetic Compatibility Classiflcations M Type of protection against electric shock Class Equipment M Degree of protection against electric shock Type B Applied Part E Degree of protection against the ingress of water Ordinary E Flammable anesthetic mixture with air of with oxygen of nitrous oxide Equipment not suitable for use in the presence of a flammable anestheticmixture with air of with oxygen or nithrous oxide E Mode of operation Continuous operation TSRK 1000P Symbols marked on the instrument Z Attention Consult Accompanying Document Protective Earth Ground O Acoording to their own law of disposal industrial waste the waste must be disposed in the country that uses our product Disposal of Waste Products Residues etc a
23. sal company to handle disposal or contact Terascience representative or distributor before disposing of the instrument The publication date 28 October 2010 So small amp yet so big So ultra compact in its size yet so enormous in its performance sciencetera Co LTD
24. ult the technical service department or your local representative Componet of Medical Device Contacting with human body Chin Forehead of patient VAN Clean patient s contact surface Headrest rubber and Chinrest with alcohol swab before every measurement CAUTION For EU countries The following mark the name amp address of EU Representative shows compliance of the instrument with Directive 93 42 EEC EU Representative Argus individuell optic GmbH 0 1 2 3 Oedenstockacher Str 11 D 85640 Putzbrunn Germany TSRK 1000P EMC Eelctromagnetic Compatibility The TSRK 1000P complies with these standards as tabled below Follow the guidance on the tables for use of the device in the electromagnetic environment EMC EN 60601 1 2 2001 A1 2006 Guidance and manufacturer s declaration electromagnetic emissions The TSRK 1000P is intended for use in the electromagnetic environment specified below The customer or the user of the TSRK 1000P should assure that it is used in such an environment Emissions test Compliance Electromagnetic environment guidance The TSRK 1000P uses RF energy only for its internal RF emissions Group 1 function CISPR 11 Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment RF emissions Class A CISPR 11 Harmonic The TSRK 1000P is suitable for use in all establish emissions SA ments othe
Download Pdf Manuals
Related Search