USER MANUAL Lec essenChill Freezer Range
Contents
1. LED indication symbols Compressor enabled s Flashing Anti short cycle delay AC parameter Defrost in progress Flashing Dripping in progress i Lec nC www lec commercial co uk 12 Energy Saving Tips The 200L units are cooled by energy efficient R600a whilst the 400L amp 600L units feature R134a refrigerant In order to keep running costs as low as possible always e Position the appliance away from heat sources e Make sure the air can circulate freely around the appliance e Ensure that products being stored in the appliance are below room temperature upon entry e Make sure the door is opened a little as possible whilst in use and closed as quickly as possible to prevent unnecessary temperature fluctuations Energy Consumption Energy Consumption kWh per 24 hours 200L 2 1 400L 6001 Storage If your appliance is to remain unused for a period of time e g during refurbishment work it is advised that the appliance is unplugged from the power supply Ensure that the interior is thoroughly cleaned and dried We recommend that you leave the door slightly ajar to prevent any bad odours from forming within the freezer Disposal of your product When disposing of your refrigerator or freezer do not take it to regular municipal waste containers Instead take it to an electrical electronic waste recycling and re use centre A relevant label has been placed on the freezers packaging see righ2. Also make sure there is good ventilation within the room www lec commercial co uk 8 2 0 Using Your Appliance Product Information Dimensions f Refrigerant Temperature Handle Door WxDxH Tvpe Ranee Colour Tvpe Type mm yp 8 yp yp BFS200W 444442236 arn i R600a 18 C to 25 C Easy Grab BFS200ST 444442637 ad i R600a 18 C to 25 C ate Easy Grab BFS400W 444442640 n a R134a 18 C to 25 C BFs4oost 444442641 803x653 x R134a ee OE TE 1960 Steel BFS600W 444442644 m ax R134a 18 C to 25 C BFS600sT 444442645 gt 743 R134a Nee was OE asaenedl sai 1982 Steel Product Details Fitted lock Fixed Wire shelves 2 adjustable front feet 2 rear rollers Electronic Controller Easy Grab Handle all 200L models Integrated Handle all 400L and 600L models Note Additional or replacement parts are also available from our Spares department Lec ori www lec commercial co uk 9 Doors Handle Styles All of the Lec essenChill 200L models feature an easy grab handle for ease of opening All 400L amp 600L models come with a stylish integrated handle as standard Reversible Doors This freezer is fitted with a reversible door which allows the user to change from right hand hinged to left hand hinged or vice versa Details on how to do this can be found on page 17 Shelves All Lec essenChill freezers come with fixed position white plastic coated wire shelves as standard Number of she
3. page 4 for details Can I purchase an extended warranty Yes Lec Commercial also offers customers the opportunity to purchase extended warranty for added piece of mind See Warranty section on page 4 for details What should I do if the lock or Key is damaged Simply call our Spares department on 0844 815 3755 and we will send arrange for a replacement lock to be fitted if the appliance is still within warranty Additional keys can also be purchased from our Spares department 10 Can I purchase replacement parts Yes we have a number of replacement parts To order please call our Spares department on 0844 815 3755 www lec commercial co uk 19 Sales Orders email sales gdpa co uk tel 0844 815 3755 opt 1 fax 0844 248 4123 After Sales email info gdpa co uk tel 0844 815 3755 opt 2 fax 0844 248 4123 Spare Parts email info gdpa co uk tel 0844 815 3755 Opt 3 fax 0844 248 4123 Marketing Enquiries email marketing gdpa co uk tel 0844 248 4274 Opt 5 fax 0844 248 4123 For all International Non UK Enquiries email info gdpa co uk tel 44 151 493 3281 fax 44 151 248 4123 Address Glen Dimplex Professional Appliances Stoney Lane Prescot Merseyside L35 2XW For any other information please visit www lec commercial co uk Lec oral www lec commercial co uk 20
4. the fixed shelves with a soft cloth using a mild detergent and lukewarm water Ensure that you rinse them totally with clean lukewarm water and make sure that they are completely dry e Detergents containing abrasives or acids are not suitable for cleaning and must NOT be used e When all cleaning has been completed reconnect the plug with dry hands DO NOT use soaps wire wool scouring powder or disinfectants of any kind Exterior We recommend that you use a good wax polish that will clean and polish the exterior of your essenChill freezer in one easy application DO NOT use an aerosol polish as the spray may damage plastic parts IMPORTANT Damage to the unit as a result of not cleaning regularly or not using the correct cleaning materials may invalidate your warranty www lec commercial co uk 15 4 0 Troubleshooting Service amp Repairs If something appears to be wrong before calling our sales department please check the following 1 Z 3 4 Make sure the plug is connected properly into the mains socket Check that the fuse hasn t blown Details of changing a fuse can be found on page 6 Check that the mains switch is ON Ensure that the door closes firmly and check the gasket sealing as this may require cleaning After Sales Support Should you require any after sales support we recommend that you contact the retailer who supplied the appliance or alternatively contact our After Sales s
5. Lec essenChill unit is left to stand for 24 hours after transportation prior to switching on as this will allow the refrigerant to settle It is essential that you clean the interior of your unit BEFORE using it for the first time We advise that the interior should be wiped with a soft cloth dampened with lukewarm water containing a mild detergent Rinse with clean lukewarm water and dry thoroughly DO NOT use soaps wire wool scouring powder disinfectants of any kind or detergents containing acids or abrasives to clean the interior Using Appliance for First Time When unpacking and cleaning are complete plug the mains lead of your appliance into a suitable earthed socket and switch on IMPORTANT We also recommend that you leave your essenChill freezer running for 24 hours before filling to ensure it is working properly Note This appliance has been supplied with a factory pre set temperature of 20 C Important Refrigerant Information All essenChill 200L models contain environmentally friendly non ozone depleting R600a refrigerant whilst 400L amp 600L freezer models contain R134a refrigerant WARNING Do not damage the refrigerant circuit As R600a and R134a are both flammable gases it is essential to avoid damage to the refrigeration circuit during transportation and installation If the refrigeration circuit is damaged avoid using a naked flame in the vicinity of the freezer and connecting power to the freezer
6. USER MANUAL lec Kt essenChill Lec essenChill Freezer Range Applicable Models BFS200W BFS200ST BFS400W BFS400ST BFS600W BFS600ST Please read and keep these instructions Contents 1 0 Important Information My Product please fill in this section Unpacking Warranty Positioning Electrical Connection Safety Information Transporting and Moving your appliance Before Plugging in Using your Appliance for First Time Important Refrigerant Information 2 0 Using Your Appliance Product Information Product Details Doors Shelves Adjusting the Feet Controller Overview Controller Operation Energy Saving Tips Storage Disposal 3 0 Care amp Maintenance of Your Appliance Defrosting Cleaning Instructions 4 0 Troubleshooting Service amp Repairs After Sales Support What Spares do we offer Replacing the Door Gasket Reversing Changing the Door Hinge Troubleshooting FAQ s Contact Information www lec commercial co uk page 3 page 4 page 4 page 5 page 6 Page 7 page 8 page 8 page 8 page 8 page 9 page 9 page 10 page 10 page 10 page 11 page 12 page 13 page 13 page 13 page 14 page 15 page 16 page 16 page 17 page 17 page 18 page 19 page 20 1 0 Important Information My Product We strongly recommend that you spend some time to fill in the information below and keep it in a safe place This will save you time if you need to contact our After Sales tea
7. cause excess frost build Can I plug my essenChill freezer in straight away after unpacking No we recommend that you leave the appliance to stand for 24 hours before plugging in to allow the refrigerant to settle after transportation and delivery You should then run the freezer whilst it s empty for 24 hours before filling Also it is essential that you have followed the cleaning recommendations on page 4 of this manual prior to filling What should I do if my floor is uneven If the floor is uneven adjust the front feet on your freezer by twisting the feet right to left or left to right so that the unit stands firm and level Can I change the temperature inside the unit Yes Lec essenChill freezers have a temperature range of 18 C to 25 C You can easily change the temperature by following the instructions on page 12 How often should I clean my essenChill freezer and how It s advised that you clean your fridge at least once a month We recommend that the appliance should be wiped with a soft cloth dampened with lukewarm water containing a mild detergent Rinse with clean lukewarm water and dry thoroughly How often should I defrost my Lec essenChill freezer It is strongly recommended that you manually defrost your freezer on average 2 3 times per year or whenever appropriate What Warranty does my Lec essenChill have Your Lec essenChill unit comes with a 2 year parts and labour warranty See Warranty section on
8. ct and activating your Lec Commercial warranty couldn t be easier Do not hesitate to call 0844 815 3755 and after choosing the After Sales option one of our advisors will be happy to assist you with this Alternatively you can register your product online at www lec commercial co uk Simply click on the Our Warranty tab located towards the top of the page and then choose the Activate Warranty option from the drop down menu In the unlikely event of breakdown please contact us on 0844 815 3755 and choose the After Sales option for assistance Remember You will need to quote the serial number of this unit This can be found on the data plate of the appliance Extended Warranty Also we now offer customers the opportunity to purchase Extended Warranty for added piece of mind Details of this can be found on our website at www lec commercial co uk or by calling our After Sales team on 0844 815 3755 www lec commercial co uk 4 Positioning vour Lec essenChill freezer When positioning your Lec essenChill freezer please ensure you have taken into account the following factors In order to conserve electricity do not place your appliance near a source of heat such as a radiator Try to avoid locations where the appliance could be exposed to direct sunlight If the product is to be placed next to another unit or a wall there should be at least a 20cm gap Increase this distance if the obstacle is a heat source This
9. d unclog the freezer The drain opening is clogged l condensate opening Operating the appliance in an Excess frost build up unheated location e g a cellar Excess condensation Operating the appliance in an on outer surface of unheated location e g a your appliance cellar surface or use adjustable feet 1 Reposition the appliance so it is at A gap in the electrical system The appliance does circuit not work The door doesn t shut tight or is opened too often The temperature inside the appliance is not low enough the compressor operates continuously 1 Move to a warmer location where temperature fluctuations are minimal 1 Move to a warmer location where temperature fluctuations are minimal The appliance makes too much noise The appliance is touching another object least 2cm apart from any other objects Lec aCi www lec commercial co uk 18 Frequently Asked Questions Are there any restrictions as to where I can locate my Lec essenChill freezer Yes for optimum performance it s important that you position your freezer on a hard flat surface in an area where the ambient temperature will not drop below 16 C or exceed 36 C Ensure the appliance has sufficient clearance around it to provide adequate ventilation We do not recommend positioning your freezer close to a heat source such as a radiator or in direct sunlight Avoid an unheated location such as a cellar as it may
10. freezer must be placed on a hard flat surface It is important that the 2 front feet are adjusted so that the unit stands firm and level The internal temperature of this appliance is affected by location room temperature and frequency of opening the door The factory settings of the electronic control thermostat are set to allow for these conditions This appliance is designed to operate in ambient temperatures between 16 C and 36 C Operating outside of these temperature parameters may cause the appliance to perform out of specification Lec oral www lec commercial co uk 5 Electrical Connection This appliance is intended for connection with alternating current The connection values for voltage V and frequency Hz are declared on the name plate in the product Power must be connected via a wall socket with a switch It is strongly recommended that the wall socket is accessible The product plug and wall socket should give correct earthing If in doubt please contact your local supplier or an authorised electrician If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard WARNING THIS APPLIANCE MUST BE EARTHED The flexible cord mains lead fitted to this product has three cores for use with a 3 pin 13 amp plug If a BS 1363 13 amp fused plug is used it should be fitted with a 13 amp fuse The cores in the mains lead are coloured
11. in accordance with the following code GREEN amp YELLOW yg AMP FUSE GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE BROWN CORD CLAMP Note These colours may not correspond with the coloured markings identifying the terminals in your plug Do not push excess mains lead into the compressor compartment If it is necessary to change the fuse in a moulded plug and the fuse cover is detachable it must be refitted after the fuse has been changed If the fuse cover is lost or damaged the plug must not be used until a replacement is obtained It is important that the colour of the replacement fuse cover corresponds with the coloured insert or as indicated in embossed words on the base of the plug Replacement fuse covers are available from our Spares department at the address on the final page of this manual Lec nC www lec commercial co uk 6 Safety Information WARNING Keep ventilation openings in the appliance enclosure or in the built in structure clear of obstruction WARNING Do not use electrical appliances inside the storage compartment of the appliance unless they are of the type recommended by the manufacturer e Before ANY maintenance activity carefully take the plug out of the socket by gripping the plug DO NOT pull on the plug cord e DO NOT use double wire extension cords If an extension cord is necessary make sure it is a cord which possesses a protection
12. lves as standard BFS200W ST 2 fixed BFS400W ST 6 fixed BFS600W ST 6 fixed WARNING Maximum loading capacity per shelf is 20kg Note All 600L essenChill freezer models are 2 1 gastronorm compatible Adjusting the feet Your Lec essenChill will come fitted with 2 adjustable front feet and 2 rear rollers as standard When adjusting the feet tilt the unit back slightly To extend the height level of the feet simply twist unscrew the feet from right to left until you reach desired level To reduce the height level of the feet twist screw the feet from left to right until you reach desired level Lec oral www lec commercial co uk 10 Controller Overview 1 Set Temperature Enter button 3 Minimum Temperature Down button 4 Start Stop Defrost 2 Maximum Temperature Up button 2 Applies to ALL models Lec orl www lec commercial co uk 11 Controller Operation View or Change the Current Set Temperature Function Press Hold button s Result down for To view set 1 second Displays current set temperature gt temperature Followed by Until desired Modifies and saves temperature is set temperature reached Followed by 1 second Exits the adjustment and displays internal temperature Manual start stop Starts or stops Defrost defrost Defrost LED l illuminates when defrost is in Note If no more buttons are pressed within 6 seconds the interior temperature will be displayed
13. m My Lec essenChill model number ts e g BFSZ00W ttt Et yy SKU Number alallala Serial Number found on the data plate of the appliance iiid Date of Purchase AA Purchased from Please take some time to fill in the information above and keep it in a safe place This will save you time if you need to contact our After Sales team Lec AONI www lec commercial co uk 3 Thank you for purchasing this Lec essenChill freezer Whilst unpacking please carry out the following actions e Check the freezer has not been damaged in any way during transportation If any damage is found it MUST be reported to our After Sales department immediately by calling 0844 815 3755 e When unpacking the appliance ensure that all packaging has been removed including cardboard polystyrene and any tape used to hold the shelves in place during transportation e The refrigerator has been cleaned prior to dispatch however we advise that it should also be cleaned before use We recommend that the appliance should be wiped with a soft cloth dampened with lukewarm water containing a mild detergent Rinse with clean lukewarm water and dry thoroughly e When unpacking is complete we recommend that the appliance should stand for 24 hours prior to switching on Warranty How to activate your Warranty This Lec essenChill freezer comes with a 2 years Parts and Labour warranty from the date of purchase Registering your produ
14. safety certificate e Ifthe main power supply cord is damaged it should be replaced by a qualified Service engineer e DONOT attempt to make any repairs to the appliance yourself Repairs carried out by someone without the relevant training are putting their personal safety at risk and will invalidate your warranty e DONOT store explosive substances such as aerosol cans with a flammable propellant in this appliance e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Remember This Lec essenChill unit is intended to be used in commercial premises and similar applications such as Staff kitchen areas in shops offices and other working environments Hotels bars pubs and cafes Fast food providers Restaurants and similar Retail premises Local authorities ie Schools nursing homes hospital kitchens www lec commercial co uk 7 Transporting and Moving your Lec essenChill freezer The product must be unplugged before moving and should always be moved in the vertical position Leave the product to stand for at least 24 hours before reconnecting Before you plug vour appliance in IMPORTANT Ensure that your
15. t The product has been manufactured using recyclable materials Ask your local environmental care authority for information concerning location of such facilities www lec commercial co uk 13 3 0 Care amp Ongoing Maintenance of your Appliance Service Information It is important to service your freezer regularly We recommend that the condenser drain and gasket are serviced every 6 months by a qualified service engineer Defrosting All Lec essenChill freezers need to be manually defrosted on a regular basis Manual defrost Instructions on how to manually defrost your appliance can be found within the table on page 12 under the title performing a manual defrost cycle IMPORTANT Do not use any knives or sharp metallic objects to remove frost WARNING Do not use mechanical devices or other means to accelerate the defrosting process other than those recommended by the manufacturer Lec ori www lec commercial co uk 14 Keeping your essenChill freezer clean Interior e Your Lec essenChill freezer should be cleaned regularly e Before cleaning you MUST switch off and disconnect the appliance from the power supply e The interior except for the door gasket can be cleaned using a mild detergent and lukewarm water before rinsing with clean lukewarm water and drying thoroughly e Regularly clean the gasket with water only and wipe dry This helps prevent the build up of food and liquid residues e Wipe
16. the hinge on the desired side Insert hinge pin in the hinge and in the door hinge bush Fasten the hinge 7 Re connect the multi plug to the panel and secure the panel Re connect to the mains Changing the door hinge requires at least 2 people and should not be attempted on your own Note A series of pictorial instructions are available on request from our After Sales department Simply call 0844 815 3755 and one of our advisors will be able to send these to you Lec ori www lec commercial co uk 17 Troubleshooting PROBLEM REASON SOLUTION 1 Make sure the plug is properly inserted into the socket 2 Make sure the socket is not faulty 3 Make sure the power supply cord is not damaged activates temperature is below 16 C 1 Rearrange the products so they don t hamper the door 2 Shorten the time the door is open for Appliance is positioned near a 1 Move appliance away from any area s heat source or exposed to where heat sources or direct sunlight direct sunlight are present 1 Check the appliance is operating at an The ambient temperature is i ambient temperature that is less than above 36 C 36 C Air circulation at the back of 1 Move product further away from the the appliance is hampered wall The contents touch the back 1 Move the products so they aren t in Water collects at the i wall of the interior contact with the back wall bottom part of the 0 1 Take the cleaning plug an
17. upport team on 0844 815 3755 Note You will need to have the date of purchase the model and serial number found on the Data Plate of the appliance to hand and state the nature of the fault What Spares do we offer A few examples include Compressor e Replacement door gasket Adjustable feet e Digital controller Lock and key e Door handles Mains cable with plug e Door hinges For further information or to purchase any spare parts please do not hesitate to contact our Spares department on 0844 815 3755 Please ensure that you have your SKU number e g 444442636 and GDPA code e g BFS200W to hand eo Chill www lec commercial co uk 16 Replacing the Door Gasket e Pull the gasket out from the door and replace it with a new one e Make sure the new gasket seals against the unit and there are no air gaps e You may use a hot air gun hair drier to mould the new gasket on to the door if required Note Replacement door gaskets are available from our Spares Department We advise that you clean the door gasket frequently Changing the Door Hinge To change the door hinge from right handed to left handed or vice versa 1 Switch off power at the mains socket and remove the plug from the mains socket 2 Remove the top panel and disconnect the multi plug inside 3 Remove the hinge pin and lift off the door 4 Move hinge from one side to the other 5 Move the handle from one side to the other 6 Place the door in
Download Pdf Manuals
Related Search