Ferm Cordless Drills FSD-960K I FSD
Contents
1. CHARGER TSD 3L 9 6 V 406178 ADAPTOR TSD 960L 3 5hr 406196 AVAILABLE SPARE PARTS FOR FSD 1800K1 REF NR DESCRIPTION FERM NR 2 KEYLESS CHUCK 406190 4 SWITCH 406189 7 BATTERY 406177 CHARGER TSD 3L 18V 406178 ADAPTOR TSD 1800L 3 5hr 406179 Ferm Do notabuse cable Never carry tool by the cable or pull it to disconnect it from the power socket Keep cable away from heat oil and sharp edges Do not touch the metal plug pins when connecting or removing the charger unit Secure work Use clamps or a vice to hold work It is safer than using your hand and it frees both hands to operate the tool Do not over reach Keep a proper footing and balance at all times Disconnect tools from power supply When not in use before servicing and when changing accessories such as blades bits and cutters Always switch off and unplug the appliance from the power supply when making adjustments Remove adjusting keys and wrenches Ensure that they are removed from the tool before swit ching on Avoid unintentional starting Do not carry plugged in tools with your finger on the switch Outdoor use Do not use the charger unit outdoors Do not expose drill or batteries to rain or damp conditions Connect a dust extraction device Whenever there are facilities for fitting a dust extraction system make sure it is connected and used Use recommended accessories The use of any other accessory or attachment other than recom2. by a qualified person to determine that it will operate properly Check for alignment of moving parts binding or breakage of parts mounting and other conditions that may affect its operation A damaged part or guard should be properly repaired by an authorised service centre unless indicated otherwise in the instruction manual Have defective switches repla ced by an authorised service centre Do not use a tool if the switch does not turn onand off Have your tool repaired by an expert This appliance is manufactured in accordance with rele vant safety standards Only experts must carry out repai ring of electrical appliances otherwise considerable dan ger for the user may result Storing tools When not in use tools should be stored in the dry out of reach of children Ferm ELECTRICALINFORMATION This product is complete with a pre wired mains plug unit If the plug unit charger or battery needs replacing contact the Helpline or your local Ferm Dealer ENVIRONMENT At the end of this products or its accessories life please recycle where facilities exist Caution batteries contain substances that are harmful to your health or the envi ronment Do not open or incinerate them Please dispose of them safely phone the Helpline for currentadvice on recycling and disposal Helpline For any questions relating to operational or safety matters contact Ferm Customer Helpline on 0115 966 1199 Monday Friday 8am 6pm Satur
3. long period recharge the battery from time to time to prevent it running down Store the battery separately in the plastic case Do not use the battery charger to charge batteries other then the one provided with drill Never open or incinerate a battery this can be dangerous and will cause risk of explosion pollution or other health hazards INSERT BATTERY Place the battery in the end of the handgrip it can only go in one way and will click when in place To remove bat tery push the tabs in on either side of the battery with finger and thumb and pull out of handgrip OPERATION To switch ON OFF Press the trigger switch 4 Tolocktrigger switch Put the left right switch 3 in the central position Speed control Adjust the drills speed by more or less pressure on the trigger switch 4 Direction of rotation Change the direction by pushing switch 3 to left or right this must be done when the drill is not rotating Inserting bits into chuck Put the bit into chuck and tighten the chuck 2 firmly anti clockwise by hand only Remove bits by turning chuck 2 clockwise Keep your finger off the trigger switch during these operations Use asascrewdriver Insert a suitable screwdriver bit into the chuck and set the torque ring to desired setting is low and 8 is high Start at low setting and increase setting until the correct setting for the job is found A Do not use as a screwdriver with the torque ring set in drill positi
4. UK Subjectto change USER S MANUAL DocumentRef FSD 960K I 13882 PMR2 Issue Mar02 FSD 1800K I 18424 PMR2 Issue Mar02 Copyright These instructions are the sole property of Ferm Omega Tools and may not be reproduced Ferm Cordless Drills FSD 960K1 FSD 1800KI Art nr 718810 Screwfix art nr 3882 960 Art nr 718870 Screwfix art nr 18424 1800 Ferm BV P O Box 134 8280 AC Genemuiden NL www ferm com 0303 06 Sinin A y FERM FSD 960KI AND I800KI USERS MANUAL TECHNICALSPECIFICATIONS Voltage 718810 9 6 V Voltage 718870 18 V Voltage battery charger 230 V Frequency battery charger 50 Hz Capacity battery 1 2 Ah NiCd Charging time 3 5h Number of drilling speeds l No load Speed 718810 0 550 min No load Speed 718870 0 900 min Weight incl battery 1 8kg Lpa Sound pressure level 75 dB A ibration lt 2 5 m s PACKAGE CONTENTS Cordless drill Battery Charger Adapter Case Instruction manual Guarantee card Safety instructions SAFETY INSTRUCTIONS The following symbols are used in these instructions for use A Denotes risk of personal injury loss of life or damage to the tool in case of non observance of the instructions in this manual A Denotes risk of electric shock Carefully read this manual before using the machine Make sure that you know how the machine functions and how to operate it Maintain the machine in accordance with the instr
5. day 9am I pm GUARANTEE The guarantee conditions can be found on the separately enclosed guarantee card CE DECLARATIONOFCONFORMITY UK We declare under our sole responsibility that this productis in conformity with the following standards or standardized documents prEN50260 1 prEN50260 2 1 prEN50260 2 2 EN55014 1 EN55014 2 EN60335 1 EN60335 2 29 EN61000 3 2 EN61000 3 3 in accordance with the regulations 98 37EEC 73 123 EEC 89 336EEC from 01 09 2001 GENEMUIDEN NL L N Ceo W Kamphof Quality department Ferm
6. mended in the instructions or catalogue may pre senta risk of personal injury Ferm USING THE CORDLESS DRILL BEFORE OPERATING Check that The voltage marked on the charger is suitable for use with your mains supply The output voltage on the charger is suitable to use with the drill battery The battery voltage is suitable for the drill A The battery supplied with the drill is not fully char ged CHARGING THE BATTERY Place the battery charger on a level surface and put the battery into the charger Make sure the terminals on the battery tongue line up with the and terminals on the charger Put the pushpin connector into the charger and plug the mains adaptor into the mains Do not use a long extension lead with the charger Only use the charger between 10 and 400 C The red light on the charger indicates the battery is being charged The first charge will take 5 hours subsequent charges take about 3 hours A The red light will not go out when the battery is fully charged Never charge the battery for more than 5 hours otherwise it will overheat Discharging the battery is as important as charging it Use the drill until it becomes less powerful and does not reach maxi mum speed the battery is now ready to be recharged Do not discharge the battery completely if this happens you will damage the battery and it will not be able to be recharged If the drill is not going to be used for a
7. ommon sense Do not operate tools when tired or after taking alcohol or pre scription non prescription drugs OPERATIONAL SAFETY Concentrate Routine and repetition can lead to mistakes Remember that a slight lack of concentration can result in serious injuries ina split second Keep workareaclean Cluttered areas and benches invite injuries Consider the work environment Do not expose power tools to rain or use them in damp or wet locations Keep work area well lit Do not use power tools in the presence of flammable liquids vapours or gases Guard against electric shock This unit contains dangerous voltages Use a RCD resi dual current device to provide protection against elec trical shock Prevent body contact with grounded surfa ces e g pipes radiator ranges or refrigerators Keep children and pets away Do not let children or pets come into contact with the tool extension cable or work area Do not force the tool It will work better and safer at the rate for which it was intended Use the right tool Do not force small tools or attachments to do the job ofa heavy duty tool Do not use tools for purposes for which they were not intended for example do not usea circular saw for cutting trees or logs Ferm EXPLODED VIEW Ferm AVAILABLE SPARE PARTS FOR FSD 960K1 REF NR DESCRIPTION FERMNR 2 KEYLESS CHUCK 406190 4 SWITCH 406189 7 BATTERY 406184
8. on this will damage the drill Useasadrill Insert a drill bit into chuck and set the torque ring to drill setting MAINTENCE CARE AND REPAIR FAULTS Excessive parking Indicates dirt in the motor or worn bushes Take the drill to your Ferm dealer Overheating The ventilation slots are blocked with dirt Clean with dry cloth The drill is overloaded Apply less load Use sharp drills Themotor is defective Take to your Ferm Dealer Battery does not charge or hold charge The battery was not properly charged discharged Try recharging and discharging it several times The battery charger is defective Contact your Ferm dealer to have it replaced MAINTAIN TOOLS WITH CARE Keep tools bits sharp and clean for better and safer per formance Use only sharp drills of the following types For Concrete Masonry Tungsten Tipped twist drills For Metal HSS Twist drills For wood HSS twist drills or CS flat wood bits AN In every case use speed and feed rates recommen ded by the drill manufacturer supplier Follow instructions for changing accessories Inspect tool and extension cables periodically and if damaged have them repaired by a qualified person or authorised service body Keep handles free from oil or grease Keep the ventilation slots clean to prevent motor overheating Check for damaged parts Do not usea tool with damaged parts before further use a damaged tool must be carefully checked
9. uctions to make sure it functions properly Keep this manual and the enclosed documentation with the machine Ferm products are manufactured to high quality stan dards they are safe and fit for purpose at time of sale but all tools can be dangerous if the correct precautions are not taken Always follow these instructions do not carry out the operation until you are sure you can do so in safety Remember consider the work environment for safe operation as well as safety for tool use Warning When using electric tools basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury Read all these instructions before attempting to operate this product Save these instructions for future reference PERSONALSAFETY Use Personal Protection Safety Equipment Protect eyes with safety glasses or goggles note the use of safety protective eyewear without the CE mark can lead to serious injury if the glass breaks A suitable dust mask should be worn if cutting drilling or sanding is dusty in particular chipboard or MDF Approved safety foot wear and headgear should worn as appropriate for example on building works or when heavy weights are involved Dress properly Do not wear loose clothing or jewellery It can get caught in moving parts Non skid footwear is recommended when working out doors Wear protective hair covering to contain long hair Stay alert Watch what you are doing Use c
Download Pdf Manuals
Related Search