Miele S 326i Operating instructions
Contents
1. The symbols on the controls indicate what each setting is suitable for curtains lightweight fabrics upholstery cushions cu o thick pile carpets rugs and runners K energy saving daily vacuuming with low noise level low pile carpets hard flooring and intensive cleaning of carpets Operation The controls vary from model to model and are described as follows Rotary selector m Turn the rotary selector to the desired suction power setting controls Press the controls until the light bar above the desired suction power setting is illuminated m Press the control to select a higher setting m Press the control to select a lower setting at the radio handpiece Press the controls until the desired suction power is shown in the vacuum display on the canister m Press the control to select a higher setting m Press the control to select a lower setting Every push of a button at the handpiece is displayed by the indicator light 20 Operation Opening the air inlet valve not available in models with radio handpiece The air inlet valve is designed to provide a quick convenient reduction of suction power e g when moving from a carpet to an area rug m Open the air inlet valve far enough to reduce the power Opening the air inlet valve2. Operating instructions Vacuum cleaner S 4002 ONLY MIELE DUSTBAGS FILTERS AND ACCESSORIES WITH THE ORIGINAL MIELE LOGO CAN BE USED WITH THIS VACUUM CLEANER USE OF NON MIELE COMPONENTS MAY VOID THE WARRANTY To prevent accidents en US CA and appliance damage read these instructions before installation and use M Nr 09 406 840 Only Miele dustbags filters and accessories with the Original Miele logo can be used with this vacuum Only then can the suction power of the vacuum cleaner reach its optimum potential creating the best possible cleaning results USE OF NON MIELE COMPONENTS MAY VOID THE WARRANTY The use of dustbags made of paper or a similar material or dustbags with a cardboard retaining plate can lead to serious damage to the vacuum cleaner and may void the warranty just as with the use of dustbags without the Original Miele logo The Original Miele Logo will appear on the packaging or directly on the dustbag Purchasing new dustbags and filters Original Miele dustbags and filters can be purchased from an authorized Miele vacuum dealer or by visiting the Miele store at www mieleusa com Contents IMPORTANT SAFETY INSTRUCTIONS 0 0 2 0 00005 5 Guide tothe machine 0 a 10 Before using the vacuum cleaner 2020000 e ee eeee 12 Using the included accessories 00 0002 e eee 15 Operatio
3. e g tiles and stone floors SBD 470 3 FiberTeQ Combination Floor Tool The floor tool is suitable for cleaning carpets rugs and hard surfaces For flooring susceptible to scratches use one of the special Miele floor brushes see Optional accessories To clean carpets and area rugs m Press the foot switch marked Jel To clean hard flooring m Press the foot switch marked fz Turbobrush Some models come with a Turbobrush as an accessory Please refer to the separate operating instructions for instruction on use and maintenance 14 Using the included accessories The following accessories are included Dust brush with natural bristles For cleaning moldings decorative or carved items etc The head of the dusting brush can be swivelled to attain the best cleaning position For dusting particularly delicate objects 2 Upholstery tool For cleaning upholstery mattresses cushions curtains covers etc Crevice nozzle For cleaning in folds crevices and corners Accessory clip for the included accessories Position the accessories as indicated with the symbols on the accessory holder m Insert the accessory holder either on the hand piece at the handle or on the hose connector of the vacuum cleaner Standard floor brush depending on model m For safety when vacuuming stairs it is best to start at the bottom and move upwards Operation Power cord Unwind
4. standby mode during pauses m Press the Standby button on the handpiece To turn the vacuum on again m Press the Standby button on the handpiece The vacuum cleaner turns on to the last selected power level m Press to turn the vacuum cleaner on at the lowest power level m Press to turn the vacuum cleaner on at the highest power level Every push of a button on the radio handpiece is displayed by the indicator light The vacuum can still be used if the battery in the radio handpiece is weak or not inserted at all m Turn the vacuum on with the foot switch m Press the Reset button The vacuum will operate continuously on the maximum suction power m Turn the vacuum off with the foot switch Only use the Standby mode for short pauses during vacuuming Do not leave the vacuum in Standby mode there is a danger of overheating and damage 18 Operation While vacuuming The vacuum cleaner can also stand on its end for vacuuming stairs drapes etc To prevent static electricity your hand must touch the metal inlay on the underside of the vacuum handpiece Be certain to continuously touch this inlay when vacuuming fine dust flour or sawdust as these materials are more likely to create a static discharge To further prevent static discharge while vacuuming pull the vacuum along by the hose with one hand while continuing to hold the handpiece in the other hand Adjusting the suction
5. Optional accessories Observe the cleaning instructions of the floor manufacturer Many of these accessories as well as other products can be purchased from the Miele Store at www Mieleusa com Some models come standard with one or more of the following accessories Turbo Floor brushes Turbobrush Turbo Comfort 3 Intended for cleaning short to medium pile carpeting Hand Turbobrush Turbo Mini Intended for vacuuming upholstery mattresses car seats carpeted stairs and other areas inaccessible with the standard Turbobrush Floor brush Hard floor 3 To vacuum sturdy hard floors e g tiles and stone floors Floor brush Parquet 3 Special brush with natural bristles intended for cleaning parquet and laminate floors especially those susceptible to scratching Floor brush Parquet Twister with swiveling head For cleaning all hard flooring e g parquet and tiles Especially suitable for vacuuming niches and tight spaces Floor brush Parquet Twister XL with swiveling head For cleaning large areas of hard flooring e g parquet and tiles 35 Optional accessories Other accessories MicroSet For cleaning small objects and difficult to reach areas such as PC keyboards stereo equipment carved furniture and ornaments models etc CarCare accessory case For cleaning car interiors Cat amp Dog accessory case For cleaning the homes of pet owners HomeCare accessory case For c
6. attachments can affect the function of the airflow indicator If your vacuum cleaner is equipped with a SBB 3 Smooth Floor Brush the test cannot be performed m Attach the floor tool to the vacuum cleaner m Turn the vacuum cleaner on and select the highest power setting m Lift the floor tool slightly off the floor If the marker completely fills the indicator window the dust bag needs to be changed 24 How the airflow indicator works The airflow indicator is designed to show when the bag is full of common household dust and to measure the amount of air flow through the dustbag Normal household dust is a mixture of dust hair carpet fluff threads sand etc However if fine dust such as drill dust sand plaster or flour is vacuumed the pores of the dustbag will become blocked The marker will indicate that the bag is full even when it is not The dustbag should be changed because the suction power is greatly reduced If the bag is bulging with pet fur hair carpet fluff etc the indicator may not register full This is because the air flow of the dustbag may still be high enough not to activate the marker to show maximum The dustbag should still be changed Maintenance and care Replacing the dustbag m Open the dust compartment lid The dustbag has a closing flap which closes automatically when the dust compartment lid is raised to prevent any dust from escaping m Grasp the collar and
7. conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced ra
8. reduces the power to the tool being used 21 Transport and storage Park System A Park System has been designed to conveniently park the telescopic wand at the vacuum cleaner during pauses m A special parking attachment is fitted to all floor brushes Insert the lower clip of the floor brush into the slot on the end of the vacuum cleaner from above When vacuuming on a sloping surface e g on a ramp push all telescopic tubing parts completely together Transport and storage m For easier transportation and storage stand the vacuum cleaner vertically insert both clips of the floor brush into the two point holder on the side of the vacuum insert one part of the telescopic wand into the other depending on model 22 Maintenance and care Turn off and unplug the vacuum cleaner before performing any maintenance work The Miele filter system consists of the following three components Dustbag Exhaust filter Dust compartment filter Each of these components must be changed periodically to maintain the vacuum cleaner s efficiency Only use Miele dustbags filters and accessories with the Original Miele logo Only then can the suction power of the vacuum cleaner reach its optimum potential creating the best possible cleaning results N The use of dustbags made of paper or a similar material or dustbags with a cardboard retaining plate can lead to serio
9. remove the dustbag from the holder m Insert the new dust bag as far as it will go into the dustbag holder Do not unfold the dustbag when taking it out of the box m Unfold the dustbag in the dust compartment m Close the dust compartment lid until it clicks into place Take care not to catch the dust bag in the lid J A empty operation barrier will block the dust compartment lid from closing if no dustbag is inserted or if it is not inserted all the way Do Not Use Force Z Ke i AWS Maintenance and care Replacing the exhaust filter Depending on model the vacuum cleaner will be equipped with one of the following exhaust filters a Air Clean filter b Active Air Clean filter c Active HEPA filter Air Clean filter An Air Clean filter is supplied with every box of Miele dustbags It should be replaced each time a new box of bags is started Active Air Clean or the Active HEPA filter An Active Air Clean or Active HEPA filter should be changed approximately once a year Change the filter sooner if it is obviously soiled or no longer effective It is helpful to note the date directly on the filter as a reminder for when to next change it See Optional Accessories for filter descriptions 26 E 5 Maintenance and care Exhaust filter change indicator Some models are equipped with an exhaust filter change indicator Reset button which is designe
10. 00 0 35 Caring for the environment 0 0 00 37 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE KEEP THESE OPERATING INSTRUCTIONS FOR FUTURE REFERENCE WARNING Use To reduce the risk of fire electric shock or injury B This vacuum cleaner is intended for use in domestic households or in similar working and residential This vacuum cleaner complies with environments all legal current safety requirements Improper use can cause both gt Do not use on people or animals abs injury ane propery P gt Do not use outdoors or on wet surfaces Only dry surfaces should be vacuumed Before using the vacuum cleaner read the Operating Instructions B gt Other uses are not permitted and carefully This will protect you and can be dangerous others and prevent damage to the gt Persons who lack physical sensory vacuum cleaner or mental abilities or experience with the appliance should not use it without supervision or instruction by a responsible person gt Do not allow the vacuum cleaner to be used as a toy Close attention is necessary when used near children IMPORTANT SAFETY INSTRUCTIONS Technical Safety gt A damaged vacuum cleaner can be dangerous Check the packaging vacuum cleaner and accessories for any signs of damage Do not use a dam
11. aged appliance B gt Check the voltage rating of the vacuum cleaner before connecting the power cord to an electrical outlet Your power source should correspond with the voltage rating plate located on the underside of the vacuum Use only household AC outlets Never use DC power sources If you are not sure of your home s voltage supply consult a qualified electrician Connecting the vacuum cleaner to a higher voltage than indicated in these instructions may result in damage to the vacuum cleaner or injury gt To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not alter the plug in any way gt If the power cord is damaged it should be replaced along with a new cable reel by Miele Technical Service P The electrical outlet must be fitted with a 15 A fuse P gt On the underside of the vacuum handpiece is a metal insert designed to absorb static electricity Please make certain that your hand remains around this metal insert when vacuuming gt Do not leave the vacuum plugged in Unplug it from the outlet when not in use and before servicing B Turn off all controls before unplugging P gt Never submerge the vacuum cleaner in water Clean only wi
12. d conditioning agents They will damage the surface Dust compartment The dust compartment can if necessary be cleaned using a dry cloth dusting brush or a second vacuum to suck out any Monitor the change dustbag indicator and inspect all filters regularly Clean or replace them when necessary according to these Operating Instructions Do not submerge the vacuum in water If moisture gets into the appliance there is the risk of an electric shock 33 Frequently asked questions Technical Service Some models have a warning light A which comes on to indicate overheating If the vacuum has overheated the temperature limiter automatically turns the vacuum off Some models also have a warning light A to indicate that the vacuum has overheated This can occur if for instance large articles block the suction tube or when the filter bag is full or contains particles of fine dust A heavily soiled exhaust or dust compartment filter can also be the cause of overheating Turn off the vacuum cleaner using the On Off switch Unwind the full length of the power cord Allow the vacuum to cool down for 30 minutes After sales service In the event of a fault which you cannot fix yourself please contact the Miele Service Department at the phone number listed on the back of this booklet m Please quote the model type of your appliance This can be found on the data plate on the bottom of the vacuum 34
13. d to alert the user when to change the Active Air Clean or Active HEPA filter The indicator will light after about 50 hours of operation which is equivalent to about a year of average use The vacuum cleaner can still be used with the exhaust filter indicator lit However the suction power will be reduced as will the effectiveness of the filter if it is not replaced If an Air Clean filter a is being used the filter change indicator can be disregarded but should be reset when it does light The indicator goes out when the reset button is pressed You can replace the exhaust filter supplied with the vacuum cleaner with one of the other types of filters see Optional accessories Reset 27 Maintenance and care Replacing the Air Clean filter m Open the dust compartment lid m Open the filter frame and remove the used Air Clean filter with the clean corner see arrow Do not use more than one filter at a time m Insert the new filter m Close the filter frame If you wish to replace the Air Clean filter with an Active Air Clean filter or Active HEPA filter see Maintenance and care Exchanging exhaust filters m Close the dust compartment lid firmly until it clicks into place 28 Maintenance and care Replacing the Active Air Clean filter and the Active HEPA filter m Open the dust compartment lid Do not use more than one filter at a time m Remove the exhaust
14. dio TV technician for help SAVE THESE INSTRUCTIONS Guide to the machine OONO P py a o 4a n G 2 D DOOOOO Some models come standard with a Turbobrush which is not shown in this figure A separate Operating manual is supplied with the vacuum Guide to the machine Handpiece some models may include an air inlet valve 2 Suction power buttons Standby switch LED Locking button Accessory clip Telescopic wand release button Dust compartment lid release Telescopic wand Dustbag Carrying handle 2 Floor brush 4 Transport storage holder Dust compartment filter motor protection 4 Exhaust filter Suction power selector Standby indicator Thermo indicator A Exhaust filter change indicator Reset button Power cord with plug Cord rewind switch Park System On Off switch Airflow indicator 5 Elbow Suction hose The features marked may vary or not be available depending on your model Before using the vacuum cleaner Attaching the suction hose m Insert the elbow into the suction socket until it clicks Use the inlet guides to direct insertion Removing the suction hose m Press the release buttons at the sides of the elbow and lift the hose from the socket Connecting the handpiece and telescopic wand m Inser
15. ed of safely and kept out of the reach of children Danger of suffocation 37 38 39 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 905 660 9936 Fax 905 532 2290 www miele ca professional miele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercare miele ca general and technical enquries Alteration rights reserved 1912 M Nr 09 406 840 00 INFORMATION IS SUBJECT TO CHANGE PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS TECHNICAL amp WARRANTY INFORMATION
16. filter m Insert the new filter If you wish to replace the Active Air Clean filter or the Active Hepa filter with an Air Clean filter see Maintenance and care Exchanging exhaust filters m Close the dust compartment lid firmly until it clicks into place Resetting the filter change indicator The filter change indicator Reset button must be reset each time the filter is replaced To do this the vacuum cleaner must be plugged in m Press and hold the filter change indicator light until it goes out The display is now reset Maintenance and care Exchanging exhaust filters 1 If you wish to replace the an Air Clean filter with the b Active Air Clean filter or the c Active HEPA filter you must remove the filter frame before inserting the new filter 2 If you use an Air Clean filter a you must insert it into a filter frame Filter frame see Optional accessories Do not use more than one filter at a time The Active Air Clean filter can be used instead of the Active HEPA filter and vice versa without any changes Remember to reset the filter change indicator with the Reset button after every filter change The indicator will go out when the reset button is pressed 30 Maintenance and care When to change the dust compartment filter motor protection Replace the dust compartment filter every time you start a new box of dustbags A dust compartment filter
17. is supplied with each box of Miele dustbags Replacing the dust compartment filter motor protection m Open the dust compartment lid m Open the filter frame remove the old filter and replace with a new one m Close the filter frame When to change the radio handpiece battery Every 18 months Keep a 3 V lithium CR 2082 battery handy How to change the radio handpiece battery m Release the battery compartment cover using a suitable tool e g a screwdriver m Remove the cover m Push the battery forward to remove replace with a new one m Close the battery compartment 31 Maintenance and care When to change the thread catcher pads of the FiberTeQ and upholstery tool The thread catcher pads on the bottom of the FiberTeQ floor tool and the upholstery tool should be checked occasionally Replace the pads if they appear worn Replacing the thread catchers m Use a screwdriver or similar object to remove the thread catchers from the slots m Insert the new thread catchers Spare parts are available from your Miele dealer or from Miele 32 Cleaning and care N Turn off the vacuum and unplug it before performing any maintenance work Vacuum cleaner and accessories External surfaces of the vacuum cleaner and accessories can be cleaned with a slightly damp cloth or with a cleaner suitable for plastics N Do not use abrasive glass or all purpose cleaners or oil base
18. leaning your home Universal brush For dusting bookshelves mantles molding ceiling fans sculptures etc Dust brush with natural bristles For dusting particularly delicate objects Radiator brush For cleaning radiators vents refrigerator coils air conditioners decorative vases etc Mattress tool For cleaning deep crevices mattresses and upholstery 36 Crevice nozzle 12 300 mm For cleaning in folds crevices corners etc Crevice nozzle 22 560 mm For cleaning hard to reach areas Upholstery tool 7 12 190 mm For cleaning upholstered furniture mattresses and pillows Filters Active Air Clean filter SF AAC 50 This charcoal filter absorbs odors from the dust collected in the dustbag Active HEPA filter SF AH 50 This filter are particularly suitable for allergy sufferers and those concerned with a high level of hygiene Filter frame The filter frame is needed if you would like to exchange a Air Clean filter with an Active Air Clean or Active HEPA filter Caring for the environment Disposal of the packing Disposal of an old machine material Old vacuum cleaners may contain The cardboard box and packaging materials that can be recycled Please protect the vacuum cleaner during contact your local recycling authority shipping These materials are about the possibility of recycling these recyclable Please recycle materials Ensure that any plastic wrappings bags etc are dispos
19. n e iene een a e E a hw adel wb beh ooo Edie aa 16 POWT GOG uae metua Gms she es e damped hae Bede see Sean oad 16 Turning the vacuum on and Off 6 ees 17 AGJUSTING INE SUCTION ccs eee ve RENN AS ha waa ead oe RE ee eee 19 Opening the air inlet valves ssc ee ees 21 Transport and storage 0 0 eee 22 Maintenance and care 0 0 eee 23 Purchasing new dustbags and filters 0 0 eee 23 Which dustbags and filters are the right ones 0 0 eee 23 When to change the dustbag 0 0 eee 24 Replacing the dustbag 24 4 2 saurssGunbavedade cada ea baa e bed a wees 25 Replacing the exhaust filter eee 26 Exhaust filter change indicator oyee repesett reser et cece 27 Replacing the Air Clean filter 2 eee 28 Replacing the Active Air Clean filter and the Active HEPA filter 29 Exchanging exhaust filters 2 0 eee 30 When to change the dust compartment filter motor protection 31 Replacing the dust compartment filter motor protection 0 31 When to change the radio handpiece battery 0 00 31 How to change the radio handpiece battery 0 200000000 00 31 When to change the thread catcher pads of the FiberTeQ and upholstery tool 32 Replacing the thread catchers 0 00220 32 Cleaning and care 0 33 Frequently asked questions Technical Service 34 Optional accessories 0
20. nd wands must not be used at head level to avoid injury to eyes and ears gt Miele dust bags are disposable and intended to be used only once Do not attempt to reuse An over stuffed dustbag will reduce the efficiency of the vacuum cleaner B gt The hose and the telescopic wand contain electrical wires Do not use the vacuum cleaner if these parts are damaged cut or punctured Avoid picking up sharp objects Danger of electric shock B gt Unplug the vacuum when changing accessories especially the Turbobrush and Powerbrush gt To avoid the risk of injury when vacuuming with a Miele Power or Turbobrush do not touch the rotating roller brush Danger of injury B gt The socket on the vacuum cleaner depending on model must only be used for the Miele Powerbrush specified for use with this appliance B Danger of injury The Miele Powerbrush is a motor driven accessory for use only with Miele vacuum cleaners The vacuum cleaner must not be used with another manufacturer s powerbrush Disposal gt Remove the battery from the radio handpiece and recycle it gt Before discarding an old vacuum cleaner please cut off the power cord and render the plug useless Ensure the appliance presents no danger to children while being stored for disposal IMPORTANT SAFETY INSTRUCTIONS FCC and Industry Canada information This device complies with part 15 of the FCC Rules Operation is subject to the following two
21. ompletely to aid the vacuum in dissipating heat B Do not vacuum items which are heavy hard or have sharp edges They could cause a blockage and damage the appliance gt Do not pull or carry by the cord use the cord as a handle close a door on the cord or pull the cord around sharp edges or corners Do not run the appliance over the cord Keep the cord away from heated surfaces gt Do not unplug by pulling on the cord To unplug grasp the plug not the cord gt Do not handle the plug or vacuum with wet hands gt Keep the power cord hair loose clothing fingers and all parts of the body away from openings and moving parts gt Do not place anything into the openings of the vacuum cleaner Do not use if any openings are blocked keep them free of dust lint hair or anything that may reduce air flow gt This appliance is equipped with a power cord reel Hold the plug when rewinding onto cord reel Do not allow the plug to whip when rewinding gt Use extra care when cleaning on stairs B Turn off all controls before unplugging IMPORTANT SAFETY INSTRUCTIONS Accessories B Do not use the vacuum without an accessory attached The rim could be damaged and injuries could result from sharp edges B Only use genuine Miele dustbags with the Miele quality signet and original Miele filters and accessories Only then will the manufacturer guarantee its safety B Floor attachments accessories a
22. t the handpiece into the telescopic wand until it clicks Use the inlet guides to direct insertion m To release the handpiece from the telescopic wand press the locking button see arrow and pull the handpiece away from the telescopic wand Before using the vacuum cleaner Depending on your model the vacuum will include one of the following telescopic wands Telescopic wand XXL telescopic wand Adjusting the telescopic wand One section of the telescopic wand is inside the other and can be adjusted for comfortable vacuuming m Press the telescopic wand release button see arrow to release the tubes and adjust to the desired height Adjusting the XXL telescopic wand This telescopic wand consists of three sections which are height adjustable m Pull and extend the lower section of the wand until it clicks Press the release button if you want to retract the lower section again m Press the adjustment button to release the tubes and adjust to the desired height Before using the vacuum cleaner Attaching the floor brush m Insert the wand into the floor brush and twist until it locks with a click m To release the floor brush from the telescopic wand press the locking button see arrow and pull the wand out of the floor brush Observe the cleaning instructions of the floor manufacturer SBB 3 Smooth Floor Brush The floor brush is suitable to vacuum sturdy hard floors
23. th a dry cloth or slightly damp cloth when disconnected from the mains supply If moisture gets into the appliance there is a risk of electric shock gt Repairs must only be performed by an authorized service agent in accordance with national and local safety regulations Unauthorized repairs could cause injury or machine damage The manufacturer cannot be held responsible for unauthorized work IMPORTANT SAFETY INSTRUCTIONS Use gt Never use the vacuum cleaner without the dustbag or filters in place Otherwise it could be damaged gt If a dustbag is not inserted the dust compartment lid will not close Do not force it shut gt Do not vacuum anything that is burning or smoking such as cigarettes matches or hot ashes The vacuum cleaner could catch fire B Do not use the vacuum cleaner to pick up liquids or damp dirt This could impair the electrical safety of the vacuum cleaner Wait for freshly shampooed carpets to dry gt Do not vacuum toner dust Toner such as that used in printers and photocopiers can conduct electricity gt This vacuum should not be used to entrap or retain any hazardous materials B Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present The vacuum cleaner could explode B Turn the vacuum cleaner off after each use and before every cleaning maintenance Pull the plug from the outlet gt Unwind the cord c
24. the cord completely to aid the vacuum in dissipating heat Do not pull or carry by the cord use the cord as a handle close a door on the cord or pull the cord around sharp edges or corners Do not run the appliance over the cord Keep the cord away from heated surfaces Do not unplug by pulling the cord To unplug grasp the plug not the cord This appliance is equipped with a power cord reel Hold the plug when rewinding onto cord reel Do not allow plug to whip when rewinding Unwinding m Hold the plug and pull the power cord out to the required length maximum 18 ft 5 5 m J To reduce the risk of electric shock the vacuum has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician Do not alter the plug in any way Danger of overheating and damage 16 Operation Rewinding m Unplug the vacuum from the outlet m Press the rewind switch briefly and the power cord will rewind automatically m Press the rewind switch again to stop the rewinding m Hold the plug so that it does not whip around when rewinding Turning the vacuum on and off m Press the On Off switch Operation Models with radio frequency controls The operating state is shown by the Standby indicator on the vacuum The vacuum can be switched to a
25. us damage to the vacuum cleaner and possibly voiding the warranty just as with the use of dustbags without the Original Miele logo Purchasing new dustbags and filters Original Miele dustbags and filters can be purchased from an authorized Miele vacuum dealer or by visiting the Miele store at http store miele com Which dustbags and filters are the right ones This vacuum cleaner uses Original Miele dustbags Type F J M and an Original Miele filters the Original Miele Logo will appear on the packaging or directly on the dustbag ORIGINAL Miele An Air clean exhaust filter and a dust compartment filter are supplied with every box of Miele dustbags If you would like to purchase additional Miele filters separately contact your vacuum dealer or Miele please quote the model number of your Miele vacuum cleaner to ensure correct parts are ordered These parts are also available to order from the online Miele store The exhaust filter supplied with the vacuum cleaner can be exchanged with another type of Original Miele filter see Exchanging exhaust filters 23 Maintenance and care When to change the dustbag Change the dustbag when the colored marker in the airflow indicator fills the display The dust bags are disposable and intended to be used only once Do not attempt to reuse Checking the airflow indicator Perform this test with the SBD 470 3 FiberTeQ Floor Brush only since other
Download Pdf Manuals
Related Search