User Manual - s3.amazonaws.com
Contents
1. TX_SPMP3_220 Music Player User Manuel In the playing if find the low level trigger pulse on P27 of J2 stop the playing D2 will be turned on D1 off means the system stop and end the SD card reading Trig P27 again D2 will be off and than start playing from the stopped point P20 and P21 on J2 are turn up and turn down buttons in the playing In the playing process if keep the P20 at low level the volume will be turned up At the MAX volume D2 turns on which means reached Keeps the P21 at low level the volume will be turned down D2 will be on which means reach the minimum point D2 is off when released the button If the system is in pause status keeps the P20 or P21 at low level also can control the volume When the volume reaches the MAX or MIN as D2 is on means the system is stopped D1 will show the volume is at the extreme D1 s on means at the extreme and off means in the adjustable range In working mode 8 interfaces control is effective too As the system is designed multi functional it has few shortcuts If you have special requirements please contact the manufacturer in advance MP3 music playing module supports 3 status lights 14 general input output in max and can be used in Human Machine Interface designing 4 9 Mode 9 features details Key control play and record When the character in the profile is 9 the module is in working mode 9 with power on 4 keys connect to J2 control the recording and playing2. TX_SPMP3_220 Music Player User Manuel 4 1 19 Switch folder saved current recording data OxAO Command 1B 10 AO 09 12345678 88 shows enter the folder named 12345678 saved in the SD card root Another example 1B 10 AO 06 B2 A5 B7 C5 D2 F4 CO D6 88 shows enter music play folder in the root The red contend means Chinese character code English letters use ASCII code Return 4F 4B 00 01 88 success enter the set folder 45 52 AO 01 88 enter failed Command 88 4 1 20 Start recording 0x88 Command 1B 10 88 09 30 31 36 38 2E 77 61 76 88 09 means the length of additional is HF 30313638 2E 776176 means the record file name is 0168 wav The name of record file can be set in the current folder Before recoding enter the commands list to the certain list Module starts to record when get the command During the recording each sector sends F to host to show now it is working If the first letter of command is the file name will be generated automatically The file name is RECXXXXX wav XXXXX is the number of recording files It will find the MAX value of numbers and plus 1 to this to name the new file For example following command is start recording files 1B 10 88 04 2A 2E 2A 88 as the specify file name is x it will generated automatically 4 1 21 Stop recording 0x81 Command 1B 10 81 01 88 The module will stop recording when gets this command In this situation the samples 21
3. P Pere TX_SPMP3_220 Music Player User Manuel 2 4 Module Interface Illustration HEADER 10X2 2 5 Interface signals features details Table TX_SPMP3_220 Music Player User Manuel Name and definition of interfaces in the table O Output pin without external pull up is 2 5V external connection can increase to 5V l Signal input pin input pin the highest input power is 5V P Power pin A Audio signal pin J2 Details No Name Type Features 1 STB l play data latch signal low level tigger 2 P20 Input key 1 enlarge GPIOO 3 P21 l Input key 2 enlarge GPIO1 4 P22 l Input key 3 enlarge GP102 5 P23 l Input key 4 enlarge GP103 6 P24 Input key 5 enlarge GP104 7 P25 Input key 6 enlarge GPIO5 8 P26 Input key 7 enlarge GP106 9 P27 Input key 8 enlarge GP107 10 MCU_TXD O Interface command TTL sends output signals 11 BUSY O Busy pin Down at audio playing Collector open drain output can be pull up to 5V 12 MCU_RXD Interface command TTL receives input signals 13 VCC_5V P I 5V external power input be connected to J7 14 MCU_SCL O I2C communication clock record signal switching line 15 VCC P O Module s 2 5V power regulator output No need of vacant 16 MCU_RST Reset pin of modules hardware Lower effective length 10mS 17 NC 18 19 GND P Digital signal ground 20 11 TX_SPMP3_220 Music Player
4. Return 4F 4B 06 01 88 show the current volume value is 06 17 TX_SPMP3_220 Music Player User Manuel Command 90 4 1 8 Current play status checking 0x90 Command 1B 10 90 01 88 Return 4F 4B XX 09 0002 0001 0000DC58 88 When XX is 80 shows under playing 81 shows pause 00 shows the playing finished In loop playing 0002 means the total number of songs is 2 0001 means current playing is the first on 0000DC58 shows the left sectors of current playing Command C1 4 1 9 Loop play the folder OXC1 play all of the files in the folder as background music Command 1B 10 C1 04 XXXX 88 X is the name of the played folder and the length is 1 8 For example the command following means loop playing all of the files in the folder music playing 1B 10 C1 09 B2 A5 B7 C5 D2 F4 CO D6 88 Successful return 4F 4B 00 01 88 Failed return 45 52 C1 01 88 Command C8 4 1 10 End folder loop playing OXC8 used to change the playing folder Command 1B 10 C8 01 88 Return 4F 4B 00 01 88 means end playing the folder successfully Command FO 4 1 11 Get basic information of current playing files OxFO Command 1B 10 FO 01 88 Return 4F 4B FO 10 ABCDEFGHMP3 000089DE 88 0x10 shows the additional data number is 16 ABCDEFGHMP3 means the name of current broadcasting is ABCDEFGH MP3 000089DE means the total sectors of current 18 TX_SPMP3_220 Music Player User Manuel playing file isOxOO0089DE Command E8 4 1 12
5. TX_SPMP3_220 Music Player User Manuel collected by microphone will not be saved on disk This will save the room to record audio files in effective period 4 1 22 To continue recording operation 0x82 Command 1B 10 82 01 88 The module will continue recoding when gets this command sampling from the paused position and save them to the disk There is no limitation of times of stop and continue The file generated at last is the same one Command 8B 4 1 23 End recording 0x8B 83 1B 10 8B 01 88 1B 10 83 01 88 If the module gets any command in above two the recording will be ended and generates the file name Notes for recording the recording supports FAT16 SD card only Before the recording please format the SD card to avoid stop caused by disk fragmentation 4 2 Mode 2 Features Details Serial ports control GPIO control ports When the configuration character is 2 the module is under the serial ports control GPIO mode The module has all of the serial port control features as module 1 but doesn t have the key control features The P20 P27 on J2 is the enlarged 8 bits GPIO of the module The system default the configuration as weak position At the same time it adds two new available control commands as following Command FA 4 2 1 Write extended GPIO OXFA Command 1B 10 FA 02 XX 88 29 TX_SPMP3_220 Music Player User Manuel XX is the value of 8 bits output GPIO port DO is the pin o
6. Music Player User Manuel 3 2 Profile Content Diagram BV Config OO MCE EAO FEW RED 14 TX_SPMP3_220 Music Player User Manuel 4 Detailed Explanation of Working Modes 4 1 Mode 1 Serial port control keys When the configuration character in profile is 1 the module is in Serial port port control keys playing mode when powered up Control the module by serial port commands or the keys connect to J2 terminal User can specify any file in any folder to be single played or all of the files in certain fold to be loop played as background music During the playing user can use stop continue key to control the broadcasting or stop it Besides that user can use serial port commands to do certain things For example read and write on board EEPROM and read the content in SD card files and do data read on the SD card sectors One of the special feature of this module is that it can record sound by sending the serial port commands 4 11 Key features serial port control playing During the playing if monitored the STB signal on J2 terminal is low stop current playing When it rose turn to next playing or wait for the control command from interface During the music playing D1 keeps shinning showing the module is reading data in SD card and send them to VS1003B to decoding and play Stop playing when test the P27 has low level trigger pulse on J2 terminal for a short while and trig it again to go on playing D2
7. Write data onto module EEPROM OXE8 Command 1B 10 E8 03 AA DD 88 AA refers to the address and can be got 00 FF DD means the data written into the address Return 4F 4B 00 01 88 module didn t check whether the writing is successful or not After wrote use host to check by read EEPROM command Command E9 4 1 13 Read data from module EEPROM OXE9 Command 1B 10 E9 02 AA 88 AA means address can get 00 FF Return 4F 4B DD 01 88 DD means the data stored at AA address in the module Command E0 4 1 14 Open a file OXEO Command 1B 10 E0 06 HZK16 88 The above command mean opening the file named HZK16 in current root Only after the open the reading can be preceded Return 4F 4B 00 01 88 means find the file in current root and open successfully Return 45 52 E0 01 88 means didn t find the file Command E1 4 1 15 Read the content in file s sectors OxE1 Command 1B 10 E1 09 12345678 0040 0020 88 The above example means reading the current open file sector and the start is 0x12345678 Offset in sector is 0x0040 64 Continuous read 0x0020 32 bytes Return 4F 4B E1 21 32 data read from SD card 88 Base in 0x21means additional data s length is 33 19 TX_SPMP3_220 Music Player User Manuel Note If the length of reading data is longer than 255 in sending it can not show the correct high level of return pack s additional data length Only shows the low level content The maximum of read
8. connected to RXD of users MCU RXD of module means data in it should be connected to TXD of the user s MCU Q9 How to initialize the MP3 module A9 Generally speaking the module is reliable and does not need the initialization The module will test the SD card automatically when power on After that BUSY pin makes the low level to high Then the module can work normally Or you can press RST to output level more than 10ms with power supply hard reset the module Q10 How to check whether the playing is finished or not A10 Test BUSY pin When in playing BUSY pin is low level when stopped the BUSY pin is high level Note the pull up resister is not included level standard is 2 5V and pull up to 5V through resister Q11 How to use serial port mode to control MP3 module by external user s MCU A11 First initialize the serial port interfaces in the user s MCU set the specifications such as baud rate and stop bit The serial port Command is composited by bytes Before send out the byte each time you have to check the MCU register Send out only after confirm it is free The delay waiting is not needed for the bytes in the same command After send the complete serial port command suggest wait for the module until it back to Ok attend to the capitalization Timeout is 100ms Resend the command if timeout Next command can be sent when get the character OR Q12 How to treat the not used pins Q12 Leave them float
9. light is off During the POST if the VS1003B failed D3 shine 10 times and restart if SD card initialization failed D2 shines 10 times and restart if there is error in file system initialization besides the insert FAT12 or FAT16 card D1 keeps shinning if read profiles in SD card D1 and D2 keep shinning at the same time 12 TX_SPMP3_220 Music Player User Manuel 3 Storage Media files Statutes This module only use FAT12 and FAT 16 FAT format in Windows format SD card as the storage media of audio files When formatting the media please confirm the file system formats in PC When MP3 module configures system mainly is to search content in two folders on SD card One is config and the other is Music Set a text file named config txt is necessary The first letter 1 9 in this file shows the current working mode Case is insensitive in file names and letters Suggest capital the first letter Folder Music is used to store the music to be broadcast In the excerpt playing mode the file names must be 000 mp3 256 mp3 3 1 Typical Application Storage Media files Storage Diagram is as following B F Config XED MED FED KEW IAW HMD Omu O 8 pa lpr m AG RB XX 8 HEHE D Ca F Config XER conte ORNL ns HD Rie a sa ALORA C a Se FHUDISK D a See G SUDISE E a Se TEST F B Config amp D Administrator RISC a E RERE SEUA 13 TX_SPMP3_220
10. P27 first than change binary to decimal numbers start to search file 000 mp3 256 mp3 in folder Music on the storage media automatically and find out the decimal 8 bits file name corresponding to the binary value In this process D2 shines one time to respond the trigger signal When the STB signal increases the music playing will start immediately The D3 keeps shinning Busy signal in playing and the output is low level When the playing finished D3 turns off If the trigger play finished STB signal lines from low to high the D2 is shinning instead of D3 and it means searching corresponding playing files failed Please check the file name affectivity in SD card If in the playing process trig the STB signal again the current playing will be stopped D3 turn off When the STB release begin to wait for the next trigger play There is a pull up resister in the excerpt signal pin In vacant status the internal testing value is 0 The module MCU testing value is 1 when connected to ground P20 is the lowest level and the P27 is the highest The file name need to be started with number than it can be corresponding to excerpt trigger which makes files management and identification easier For example the file named 006 work finished music go home mp3 saved in folder music when test the STB trigger signal and read the decoding value is 006 the music will be found and played automatically When use MCU or PLC to co
11. Power on and self checking finished D1 keeps on D3 keeps on wait for the key to start the recording playing D3 is the light for recording playing status D3 s on means the system is in playing status power default D3 s off means in recording status P20 and P21 on the J2 stand for back one and next one In the playing you can switch on the songs P26 on J2 is the switcher of recording and playing When the module doesn t play or record this key is used to switch to make it achieve On press one switching When the system is in playing status D2 is light on D3 off When the module in playing or recording press the key on P26 the current playing or recording will be ended Key on P27 of J2 is the switcher of pause and on When the system is waiting for playing recording press this key to start it When the system is playing recording press this key to switch on pause on If the module in playing press this key will stop it Second press will start it Switch like this If the module is in recording press this key to stop it and again to go on 27 TX_SPMP3_220 Music Player User Manuel 5 Audio output instruction 5 1 The chipset used has built in headphone amplifier It can be connected directly to 16 32 Ohm stereo headphones 5 2 Connect audio output to PA the first way is recommend 5 2 1 The first way of connecting PA input around PA input right channel PA input left 100uF channel 5 2 2 The
12. TX_SPMP3_220 Music Player User Manuel User Manual TX_SDMP3_ 220 Music Player Module Version 4 1 Date 2011 04 20 TX_SPMP3_220 Music Player User Manuel Table of Content Introduction of specifications and performances Instruction of the diagram and pins Statutes of file stored on storage media Working mode instruction Audio output instruction Appendix FAQ Contact TX_SPMP3_220 Music Player User Manuel 1 Introduction of specifications and performances TX SDMP3 220 music player module hereinafter referred to as MRM is a device that can be used as a recorder and player The storage media used is the reliable exchangeable small SD card The module can play for a long time therefore it is widely used in high definition sound needed places such as the shopping mall broadcasting background music needed public sound system of gaming devices schools and etc MRM uses MP3 music compression and reduction SoC and guarantees the sound quality to meet the requirements of background music Compare to the voice recording chip used in the embedded system the MRM has advantages as following 1 1 Nice sound quality 48 KHz reached when playing 16K sampling during recording ADPCM coding Other normal module cannot reach no higher than 8K which makes them is not suitable for the high quality background music using or broadcasting 1 2 It uses the standard memory card to store the music After users edit the music in comp
13. User Manuel J8 Signal Feature Details No Name Type Features 1 LEFT A O Left channel audio signal output 2 RIGHT A O Right channel audio signal output 3 GBUF A O Signal output common reference 4 AGND A P Module signal ground 2 6 Module LED Features Details self checking and working mode There are 3 status indicators LED and one power LED on MP3 play module The features details are as following D4 D1 D2 D3 Power LED When supply power normally to module and power output from the regulator it keeps shinning SD card status LED With power charged the module will check the SD card itself If is ok the light keep shinning or it will be shut down Please check the card inserting and the configuration is correct or not During playing and recording the lighting shinning shows there are operation on SD card sectors The higher frequency of the operation the higher frequency of shinning will be MCU working status LED When MCU is waiting for the external trigger command the light is shinning it is upper to the working mode There will be the specified agreement to the working different working mode when the MCU get the trigger command Please check the definition of this light in each working mode Handshake signal line BUSY status LED When the BUSY signal line is 0 the light is on to show the system is busy and can not accept the new commands When BUSY is 1 the system is free the
14. cally If J5 is in shorted condition recording process is operated automatically During the recording the J5 is also under testing When the short turn to blank the recording will be stopped and change to play operation automatically Mode 9 Use four keys to achieve recording and playing The control keys are connected with J2 pins Module Specifications Support whole series MPEG 1 amp 2 audio layer 3 ISO11172 3 coding including CBR fixed rate VBR and ABR see appendix Support WMA WAV and MID files playing Use VS1003B as the chipset Sound quality is excellent DAC is 18 Dynamic range is 90dB SNR is 85dB e Onboard column diode microphone It can record automatically Control the recording through serial ports making it more convenient e Support SD specification V1 0 including MMC card 1 MB 2GB produced by SanDisk Toshiba and Kingston SD card Mini SD card support SD specification V1 1 including Micro SD card e Support FAT12 and FAT16 file system completely e Audio data should be arranged followed the agreed file names The maximum of audio files in each folder can reach 65000 It can play hundreds of thousands of audio files in total e Multiple control modes including direct excerpt choosing mode loop mode decoding excerpt mode interface mode remote control mode and etc e Auto play feature It can play all audios in one folder automatically There are no special requirements of file names Fin
15. d the audio files automatically and no needs of external intervention Encryption play features It can play the audios which are simple different and encrypted Optional e lt has 0 250 level smooth volume adjustment 0 level is mute and 250 is the max The interface can control the volume and checking the current volume The keys step value is 16 and divided to 16 levels TX_SPMP3_220 Music Player User Manuel Size 57mm 71 5mm See dimensions Input power can be DC 3 7v 9 1v Support impedance 30 earphone output and external power amplifier There is one power indicator and three status indicators During the playing the certain indicator is shinning Working status is straight front Onboard standard 3 5mm power seat and earphone seat make the connection with system more efficiently The connection also can be achieved by 2 54mm pins Use on board MCU with flash and reserved the program download interface User can make the second development supply the development board to large volume customer only Standard TDC20 pins spacing 2 54mm or socket connection to connect Module offers 256 byte EEPROM no data lose when power off and support to read and write of single byte of any byte unit through interface External MCU interface both 3 3V and 5V interface level can be connected to the module by connecting lines directly The I O level meets the CMOS specifications Through serial port commands it can read the contents of certain sect
16. e time keep the module far away from ground to avoid the generation of electromagnetic induction Q4 Why there is no noise when use headphone playing while PA playing has A4 Because the module has high SNR and low LN the noise is hard to be found by headphone When uses PA the PA circuit introduces the noise of its own Suggest use nice quality PA circuit and two stage amplification reduce the noise from before class and avoid self excitation caused by single stage high magnification When use PA playing please use connect drawing mode 1 in introduction unit 6 to connect GND instead of GBUF Use coupling capacitors around 100uF Q5 Why does the voice become lower when connect the MP3 module to PA playing compared to connected to computer s sound card A5 Because this module uses DAC to output directly and the computer sound card has Op zoom Suggest turn up the volume in interface mode and two stage amplifier circuit to avoid self excitation caused by single stage high magnification Q6 Does it support SD card larger than 2 GB 239s TX_SPMP3_220 Music Player User Manuel A6 Until now it only supports SD card or MMC card not larger than 2GB Q7 Will too many files in SD card effect on the playing A7 It won t However it will need more time to switch music Q8 About the connection between MP3 module and external user s MCU is it directly or crossly A8 Do it crossly The TXD of module means data output it should be
17. er use the expect signal line of J2 as controllable GIPO port It is equivalent that the mode expended 8 I Os Mode 3 Infrared wireless remote playback operation optional Infrared wireless control can be used Under this way when make recording user only can use the automatically generated file name and save it in the specified folder The module needs custom The standard mould V2 2 doesn t support this feature Mode 4 433M wireless remote playback operation It is similar as mode 3 It uses the no directional radio to control the mould Mode 5 Timing music playing Set the time through 8 GIPO ports of J2 Read the set data when open the player and countdown start When timing time reached start the module music playing operation Mode 6 Direct excerpt play 8 excerpt signal lines Maximum is 8 songs for option Choose 1 of 8 Press any key of these 8 ports on J2 interface the related songs will be played Mode 7 Decoding excerpt play 8 excerpt signal lines Maximum is 256 songs for option Connect the 8 excerpt ports on J2 interface to the 8 DIP switch Set the related songs through DIP switches Hair low trigger pulse through the STB signal lines on J2 interface Then the module will choose corresponding song to play TX_SPMP3_220 Music Player User Manuel Mode 8 Auto play and recording No needs of external parts In this mode check the terminals of J5 s jumper If it is blank play operation automati
18. f module P20 AND D7 is correspond to the pin of P27 Return 4F 4B 00 01 88 means success Return 45 52 FA 01 88 means the current module doesn t support this command Please check whether the module is under mode 2 or not Command FB 4 2 2 Read extended GPIO 0xFB Command 1B 10 FB 01 88 Return 4F 4B XX 01 88 XX means the statue value of J2 s P20 P27 and D7 means P27 In mode 2 the extended GPIO defaults weak position The push free input enter only and the open drain modes need to be costumed with manufacturer in advance In mode 2 press the keys on STB of J2 can stop the current playing 4 3 Mode 3 features details infrared wireless control playing Optional When the configuration character in profile is 3 the module is under the infrared wireless control playing mode User can exchange last one next one turn up down pause go on the volume features wirelessly The output signal from integration infrared signal receiver connects to pin 17 of terminal J2 When receive the signal the module stops and finishes receiving The transmitter chip supporting remote control defaulted by module is widely used TC9012 or compatible chip The serial port of control signal is constituted by boot code 9ms OE OE function code features anti code When use infrared control general using TC9012 remote controller frequency the back and the next to the corresponding song The volume up and down key co
19. ing Q13 What should be paid attention when use 5V MCU to control MP3 module A13 The module has protection circuit Generally speaking connect it directly to the module is ok However avoid high current input to the module 33 TX_SPMP3_220 Music Player User Manuel 34
20. ing data length is 0x0200 512 bytes Over will be not effective Start address can from 0x0000 to 0x01FF however the length of start address data can not longer than 0x0200 or the reading content is more than the capacity of 1sector data goes invalid Command F9 4 1 16 Send data to extended serial port OxF9 Command 1B 10 F90XAA BB CC FF 88 The interface extended from MP3 module uses fixed baud rate 9600 bps to send out data Interface communication format is 1 start bit 8 data bit no parity and 1 end bit 0X means additional data length is the one sent to interface plus 1 The maximum is 13 AA BB CC are the content sent to the module extended interface The quantity is 1 12 12 effective data can be sent in one time Over the module won t send and return to error Command F5 4 1 17 Read data on SD card sector OxF5 Command 1B 10 F5 05 AABBCCDD 88 AABBCCDD is four bits SD card absolute sector number like usually MBR is at 00000000 Return 4F 4B F5 EB 3C 90 5A A5 88 in total512 5 517 bytes EB 3C 90 5A A5 is the content read in sector on SD card Return 45 52 XX 01 88 means the reading is failed XX is the error signal of reading process Command C2 4 1 18 Use MP3 module to do reset operation 0xC2 Command 1B 10 C2 01 88 MP3 module does the reset operation when get this command Reinitialize the hard software related to MP3 module which is same as the power reset feature 20
21. n SD card If in playing process and STB triggers low level end the current playing Wait for the next playing operation of P20 P27 If there is low pin in P20 P27 when playing is finished the corresponding music will be played continually The file name need to be started with number and than it can be corresponding to excerpt trigger which makes files management and identification easier For example the file name is 002 wake up music mp3 in folder music when P2 1 is test low level the song will be played automatically When use MCU or PLC to control the music playing module the low level trigger pulse needs to bigger than 10mS to guarantee the trigger module effectively The over short pulse is treated as interrupt and no responses The module is designed follow common excerpt functions If more direct excerpt choosing or other special functions such as after chapter 1 and chapter 2 phase play music 001 please contact the producer in advance 4 7 Mode 7 features details Decoding excerpt play When the configuration character in profile is 7 the module is under the decoding except play mode It can play 256 music files which have been recorded to storage media in maximum Powered and self checking finished if everything is normal D1 keeps shinning D2 and 25 TX_SPMP3_220 Music Player User Manuel D3 are off When the module tests the STB on J2 terminal is lowered it will read the high low level of pin P20
22. nter the folder music play in the root Red content in the middle is Chinese machine code English letters use ASCII code Return 4F 4B 00 01 88 enter the specified folder successfully 45 52 AO 01 88 ender failed Command 80 4 1 6 Play audio file with specified name in current folder 0x80 Command 1B 10 80 13 12345678 MP3 88 shows playing the file named 12345678 MP3 in current folder Another example 1B 10 80 08 30 30 31 2E 6D 70 33 88 shows playing 001 MP3 file in current folder 16 TX_SPMP3_220 Music Player User Manuel Return 4F 4B 00 01 88 show search the file successfully and started to play During broadcasting MP3 module lowers the busy line D3 light turns on D1 keeps shinning When the broadcasting finished Busy raise up D3 turns off D1 turns on which indicates that the MP3 module can accept new command Command 81 4 1 2 Pause 1B 10 81 01 88 Return 4F 4B 00 01 88 D2 turns on in pause Command 82 4 1 3 Continue to play 1B 10 82 01 88 Return 4F 4B 00 01 88 Command 83 4 1 4 End current playing 1B 10 83 01 88 Return 4F 4B 00 01 88 CommandA4 4 1 7 Volume control and checking 0xA4 Command 1B 10 A4 02 XX 88 XX value is 0 250 0 is mute 250is the maximum Return 4F 4B 56 01 88 set the volume successfully the current volume of return module is 0x56 the higher value the lower volume Command 1B 10 A4 02 FF 88 checking the current volume value
23. ntrol the music playing the trigger pulse needs bigger than 10mS to guarantee the trigger module working effectively The over short pulse is treated as interrupt and no responses Mould is designed after common decoding function If any special requirements such as play total control switch input and excerpt selection Serial port II control please contact the producer in advance 4 8 Mode 8 features details Auto play and recording When the configuration character in profile is 8 the module is under the working mode 8 Powered and self checking finished it check the J5 jumper status if it is short plug in jumpers it is in recording When in recording D1 and D2 are shining which means the system is recording At that time you can use the earphone seat to monitor and hear the content If in the recording up plug the jumper on J5 which makes the J5 in open circuit the recording will be stop automatically and turn to the playing The number of each file is auto increment With power on when J5 is in open circuit the system is in auto play mode It will find the all of the songs in the folder music which can be played automatically Play it from the first one till the last And then return to the first one to play again In the playing if find the STB signal of J2 is low it will stop the current playing When the signal rises it starts to play next one In the playing D3 Busy signal light is on and D1 shinning 26
24. older music in turn when reaches the timing point In timing process D1 and D2 are off System will put audio decoding chip VS1003B and SD card in reset status to save power D3 shines each second It shows the system is working Remove the power LED D4 to save more power Module is designed follow the multifunction MP3 player If you want to use shooter basic timer unit such as 1 second longer timer value or do other operation at the same time when reach timing point such as outputting replay signal open amplifier power and etc please contact the producer in advance 4 6 Mode 6 features details Direct excerpt play When the configuration character in profile is 6 the module is under the direct except play mode It can play 8 music files which have been recorded to storage media in maximum Powered and self checking finished if everything is normal D1 keeps shinning D2 and D3 are off Module monitors the P20 P27 of J2 terminals low level and search file 001 mp3 008 mp3 in folder Music on storage media automatically Find out the files corresponding to low level P20 P27 and start playing immediately Priority from small to large is P20 P21 P27 In music playing D3 keeps shinning busy signal and low level which means the playing is undergoing When playing finished D3 turns off If user triggers play but the D2 shinning instead of D3 it means searching corresponding playing files failed Please check the file name affectivity i
25. or of specified file in folder on SD card It uses the FAT buffer technology and the speed of reading large files is still very high Serial port communication uses the interrupt mode Though in the high speed MP3 playing mode the host can query the working condition of modes by sending commands and get the responses User can know whether the mode is working or not by sending query commands as well as the playing speed Use the hardware independence technology In the module working mode1 both the interface commands control and the external keys connected through J2 control are effective One TTL UART interface Output baud rate is 9600 which can be used in testing and communication Serial port commands support to read any sector in SD card and send the data to host to analysis It makes file system testing and special features achieving easier such as finding the SD card s content and file system kinds anglicizing Under working mode II besides the music playing the external 8 keys compatible to MSC 51 GPIO completely They can read I0 s value and write the GPIO and finish the control of peripheral TX_SPMP3_220 Music Player User Manuel 2 Instruction of the diagram and pins 2 1 Module Front View TX_SPMP3_220 Music Player User Manuel 2 2 Module Back View _ TX_SPMP3_220 Music Player User Manuel 2 3 Module Dimensions 000000 o o o o o o o e e
26. r status No PT2272 output MP3 module Feature details 1 DO P20 Volume up 2 D1 P21 Volume down 3 D2 P26 Back song 4 D3 P27 Pause continue 5 D4 STB Next song The module is designed after popular MP3 playing functions If wireless control excerpt playing like press key1 to play song 1 and so on other special function s development or the analysis of development code support the wireless controller 8421BCD please contact the producer in advance 4 5 Modes features details timing music playing When the configuration character in profile is 5 the module is under the timing music playing mode It is equivalent to timing open Loop playing all the music in the folder Music Basic operation is the same as mode 8 P20 P27 connected to terminal J2 are module s timer value configuration pins P20 P23 is minute configuration pins and P24 P27 is hour configuration pins Time length basic unit is 5 minutes P23 P20 1 hour P27 P24 Therefore if minimum timer value is 0 the maximum is 15 hours 75 minutes For example P20 P27 is 1001 1000 means timer 1 hour 45minutes For example if timing start playing in 8 hours P20 P27 s setting value is 0000 0001 When module is under working mode 5 read the timer length configuration value of pin J2 s P20 P27 after power on Than start the timing operation Play all of the music files in 24 TX_SPMP3_220 Music Player User Manuel f
27. rresponds to the module volumes up and down Mute and return key correspond to module s pause play key When use the infrared control local buttons are effective See details in the introduction of mode 8 Do not use them in the same time to avoid interrupt The module is designed after popular MP3 playing functions If infrared control excerpt playing like press key1 to play song 1 and so on other special function s development or add special remote control chips supporting please contact the producer in advance 23 TX_SPMP3_220 Music Player User Manuel 4 4 Mode 4 features details wireless remote control playing When the configuration character in profile is 3 the module is under the wireless control playing mode It uses wireless controller This control signal s general uses PT2262 coding and 433M sending No direction in receiving The remote controlling can be in 100 300 m and can across the wall The receiving of wireless remote control general uses the receiving module with decoding signal Attention that the decoding chip uses PT2272 with suffix M or compatible chip to achieve That means the output decoding signal is pulse PT2272 M6 data bit output is decided by remote control sending Just follow the following table to wiring Note PT2272 M6 defaults level as low When the signal comes it is high level pulse trigger Not used features and connect the feature pin to ground directly make it in no trigge
28. second way of connecting check the power supply before using 28 TX_SPMP3_220 Music Player User Manuel PA input ground PA input right channel PA inout left channel Notes When amplifier board and MP3 module share the same low level power you can not use the second way For example there is switching power supply of 12V and 5 V which share the same ground you should use the first way to guarantee the potential of ground and etc Module is simple designed If you need module on board audio isolation capacitance or add power amplifier to drive the speaker directly please contact the manufacturer in advance 29 TX_SPMP3_220 Music Player User Manuel 6 Appendix 6 1 File formats supported by MP3 module e This module can decode MPEG 1 and MPEG2 audio level Ill CBR VBR ABR WMA 4 0 4 1 7 8 9 5 384kbps all stream files WAV PCM IMA AD PCM e Common MIDI SP MIDI files 6 2 Module electrical features Testing environment 5V DC regulated power supply Specifications Min Typical Max Unit Storage temperature 65 150 Working temperature 0 70 ie Povver 3 7 5 9 V DAC resolution 18 Byte Total harmonic distortion 0 1 0 3 Dynamic range 90 DB SNR full scale signal 70 DB Separation 50 75 DB Gain offset 0 5 0 5 DB Frequency response 0 1 0 1 DB Output signal peak 1 3 1 5 1 7 Vpp Audio output load 16 30 Q resistance Audio Outpu
29. t load 100 PF capacitance Supply current idle 29 MA Power 128kbps 44KHz 45 MA 5v 320 MAX volume Power 54 MA 350kbps 48KHz 5v 320 MAX volume 30 TX_SPMP3_220 Music Player User Manuel VIL input low power 0 5 1 1 3 V VIH input high power 1 5 1 75 5 V VOL output low power 0 2 0 3 V VOH output high power 1 8 2 1 V P20 P27 trigger time 20 ms Trst 10 ms 31 TX_SPMP3_220 Music Player User Manuel 7 FAQ Q1 Why there is sonic boom in playing and the event location is same and disappear when SD card changed A1 Because the SD card has bad block which damage the auto data and this will cause incorrect decoding Use SD card of good quality We suggest using the software MyDiskTest to test the bad block If there is any please change them instead of repairing Q2 Why there is sonic boom when start playing but not in the playing A2 Because there is an impulse responds caused by the DAC and external connected PA circuit when start playing This is a kind of physical phenomena can not be avoided Normally it is not obvious Suggest add 20 30 ms blank data when start the play in self made MP3 audio to avoid wrong decoding Normal MP3 s volume will increase step by step so the impact is less Q3 Why the noise CZ comes out in the playing A3 This is the AC sound interference Please use the high quality power with EMC supression At the sam
30. turns on in pause and turns off in playing P20 and P21 pins of J are the keys for the volume up and down When the volume reaches limits D2 turns on and turns off after release the keys 4 12 Serial port communication protocol serial ports control playing Communication protocol J2 terminal is the UART serial port that used to talk to the MP3 module It can be connected to host MCU s TXD RXD directly If it is needed to communicate with RS232 of PC it has to be level changed from TTL to RS232 first The baud rate of module communication is 9600bps 1 start bit 8 data bits 1 stop bit and no parity The protocol uses command and ACK format The packet sent from host to MP3 module starts with 0x1B 0x10 The ACK packet sent from MP3 module back to host MCU starts with Ox4F 0x4B or 0x45 0x52 depending on the status of execution of commands 2455 TX_SPMP3_220 Music Player User Manuel Format of command packet 1B 10 XX command number N length of additional data N bytes including end character 0x88 Supported command sets are as following Command 0 4 1 1 Online command 1B 10 00 01 88 Successful return 4F 4B 00 01 88 Return other contents or no return indicates the poor communication Command AO 4 1 5 Enter file folder command AO Command 1B 10 AO 09 12345678 88 represents entering the folder named 12345678 in the SD card root Another example 1B 10 AO 09 B2 A5 B7 C5 D2 F4 CO D6 88 shows e
31. uter the music can be written to the memory card through cheap card reader writer instead of the expensive professional audio edit devices MRM meets the requirements of flexibility and saves the cost as much as possible 1 3 Flexible control It can be controlled by serial ports or parallel ports The parallel ports are used in excerpts playing and it can also be controlled by keys or MCU It can be used in the fixed excerpt playing places such as the voice player and voice alarm 1 4 1Large capacity The 32M SD card can record more than 2 hours It is suitable for the long time recording It can replace the tape recording device completely and be used to record the live broadcasting music The module supports 9 working modes Working modes are saved in SD card so user can choose the certain one freely Following is the introduction of them Mode 1 Serial port control keys optional After the booting process wait for the serial port commands When get the command interpret it It can play the certain file in the certain folder in SD card When make recording user can specify the folder name and the file name and also can use the automatically generated file name During the playing connect the keys to expect signal line of J2 can control the play operations such as music selections and volume adjustments TX_SPMP3_220 Music Player User Manuel Mode 2 Serial port control 8 GPIO control ports It is the same as the mode Howev
Download Pdf Manuals
Related Search