Hardware Manual
Contents
1. PC wipe it gently with a soft cloth dampened with either water or mild detergent Do not use chemicals or a volatile solvent such as benzene or thinner to prevent pealing or discoloration of the paint Do not use any sharp pointed object such as a mechanical pencil to touch the touch panel Doing so may scratch the touch panel resulting in malfunctions Do not subject the touch panel to shock as doing so may break it When the surface or frame of the touch panel has become dirty wipe it with neutral detergent Do not wipe the touch panel with thinner alcohol ammonia or a strong chlorinated solvent Use a protective sheet available as an option if the touch panel is used where it can easily collect dust and dirt The touch panel may be damaged if adhesive tape is applied and then peeled off its surface The touch panel may be damaged if a suction cup is applied and peeled off its surface Do not use a cutter or steel wool to scrape foreign matter off the touch panel Also do not clean the touch panel with dry waste Do not clean the touch panel with the waste which has been soaked in a strong chemical or detergent e g acetone xylene toluene general thinner ketone solvent acidic alkaline chemicals and detergents abrasive chemicals and detergents or it may result in a stain or malfunction When cleaning the touch panel soak soft waste in water squeeze it firmly and use it on the surface in a lightly rubbing motion Do no2. The operating lifetime of the touch panel is at least 1 million touches as tested by mechanical touching under 1N of force at a rate of five presses per second 4 Power supply The expected battery life is 5 years in continuous operation at 40 C However the battery will not last as long if used at a temperature exceeding the operating temperature limit 5 Flash memory NFDISK The number of times of rewriting has restriction that is more than 1 000 000 When the write size is 128KB or less Since CF CARD is used for Flash memory NFDISK When use is carried out for the use that rewrites frequently be careful of the number of times of rewriting Moreover when power supply OFF is done while writing it data in flash memory NFDISK might be damaged CONTEC accepts your request for replacing each consumable in the PANECON PC as a request for repair at an additional cost Be sure to turn off the power before plugging or unplugging any expansion board or connector CONTEC reserves the right to refuse to service a product modified by the user In the event of an abnormal condition or malfunction please consult your retailer Use an AC cable that is compatible with both the rated supply voltage and the receptacle To connect with peripherals use a grounded shielded cable This product contains a lithium battery as the primary cell and a cold cathode tube for the backlight When disposing of the product therefor
3. 14 PCMCTA PCMCTA EE 15 UB ie sous areata ent waren ed 15 External Speaker Output Terminal ninia 16 TOUCH TE ico 16 Anal RGB VE sario ae 17 4 HARDWARE SETUP 19 Hardware e ie anene ATA EEEE TEA AE EAE TEE E 19 Thstallation Requirements ds 20 Attaching the cover for this product 21 Attaching the PCMCIA card removal prevention Tnges 22 Back light xchan iia 22 Attaching the USB cable removal prevention Clamps c cssessceseseeseseeseeeeseeeseeeeseeeseeeeseereneees 23 CONTEC PC PT020 Hardware Manual 111 Attaching the AC cable removal prevention clamps 25 Attaching to the VESA ATM aa 27 5 LIST OF OPTIONS 29 CONTEC lv PC PT020 Hardware Manual 1 Before Using the Product 1 Before Using the Product About the Product This product is a panel computer based on Windows CE NET 4 2 which has an excellent dustproof drip proof structure It uses SH 4 with 128MB of memory as its CPU The touch panel has an analog resistive glass glass style screen with excellent durability The frame is made of rust resistant stainless steel as well as in an IPX2 rated drip proof structure The front side has an IP65 rated dustproof and drip proof structure This product comes with various expansion interfaces such as USB PC card 100BASE T and RS 232C interfaces In addition the product can be mounted on an LCD arm as it complies with the VESA standard Features SH 4 type CPU with 128MB of memory and rewritable erasable 128MB Fl
4. ESA 100mm standard allows you to install this product on an LCD arm System development support tool CONTEC Manager provided This product comes with CONTEC Manager which helps you build a range of systems such as FTP server function scheduling function NTP based automatic time adjustment function and Auto RUN function CONTEC PC PT020 Hardware Manual 1 1 Before Using the Product Customer Support CONTEC provides the following support services for you to use CONTEC products more efficiently and comfortably Web Site Japanese http www contec co jp English http www contec com Chinese http www contec com cn Latest product information CONTEC provides up to date information on products CONTEC also provides product manuals and various technical documents in the PDF Free download You can download updated driver software and differential files as well as sample programs available in several languages Note For product information Contact your retailer if you have any technical question about a CONTEC product or need its price delivery time or estimate information Limited One Year Warranty CONTEC products are warranted by CONTEC CO LTD to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Me
5. IPC Series PANEL PC with NET4 2 SH 4 20 Series Hardware Manual CONTEC CO LTD Check Your Package Thank you for purchasing the CONTEC product The product consists of the items listed below Check with the following list that your package is complete If you discover damaged or missing items contact your retailer Product Configuration List Pes Pes PANECON PC NN Attaching cover for the main body a PCMCIA card removal prevention fittings 1 CONTEC SDK for CE420 Screws for attaching the PCMCIA card EU Declaration of Conformity removal prevention fittings Three point sems screw M3 x 6 AC power cable removal prevention clamp IPC Precaution List USB cable removal prevention clamp EN Product guide EN AC power cable Notes User s manual is not bundled with this product it must be prepared by the user Product Configuration Image P y PCMCIA card AC power cable removal removal Attaching cover prevention fittings prevention clamp for the main body M USB cable removal PANECON PC prevention clamp CONTEC SDK for CE420 IPC Precaution List AC power cable EU Declaration of Conformity a P RR Three point sems screw IPC Precaution List EU Declaration of Conformity Product guide CONTEC PC PTO20 Hardware Manual i Copyright Copyright 2007 CONTEC CO LTD ALL RIGHTS RESERVED No part of this document may be copied or reproduced in any form by any means without
6. ash ROM This product comes with SH 4 CPU 128MB of memory and Windows CE NET4 2 OS It also has a 128MB Flash ROM which can be used as a user area and allow the user to write and erase user programs Whole frame in IPX2 rated drip proof structure front side in IP65 rated dustproof drip proof structure The whole frame is IPX2 rated and waterdrop proof The front side is in an IP65 rated structure that protects against dust and streams of water For the touch panel an analog resistive glass glass style film with excellent durability has been adopted Rust resistant stainless steel used for the cabinet For the frame rust resistant stainless steel has been adopted with a protection cover that protects the interfaces against waterdrops Expansion interfaces such as USB and PC card for PC standard This product has two USB ports a PC card slot Type II x 2 or Type III x 1 100BASE T x 1 RS 232C x 2 analog RGB and stereo sound functions The main frame has small built in speakers which allow you to switch to external speakers The analog RGB interface supports dual screen display This product also comes with the drivers required for the built in interfaces as standard equipment XIP ROM module enabling high speed startup as fast as approx 10 seconds As the OS image is pre loaded in the XIP ROM the OS can start as fast as about 10 seconds after power up Mounting structure supporting VESA 100mm standard Mounting structure supporting the V
7. cifications Functional Specifications Table 2 1 Functional Specifications IPC PTO20L8 AC 48 LCD type LCD type 12 1 inch TFT color LCD 800 x 600 Number of colors 65536 Touch panel 4096 x 4096 emulated in 800 x 600 mode Resistive film analog glass glass type PU SH 4 HD6417751RBP Data 16KB Instruction 32KB Clock frequency 240MHz Memory Flash memory 128MB NFDISK OS loading 32MB Flash memory COM port RS 232C 2ch COMI 16550 9 pin D SUB COM2 16550 9 pin D SUB Baud rate 50 115200bps RTC The real time clock is accurate within 1 minutes at 25 C per month DALLAS CO LTD DS12887A 10BASE T 100 BASE TX 1ch NS CO LTD DP83816A PC card slots PCMCIA Type II x 2 or Type HI x 1 EE speakers LED Output terminals for external 3 5 Stereo mini jack Full scale output level 1 0Vrms Typ Built in speaker Rated input 0 3W Connected to analog L signal of stereo output DIPSW Front function switch Front switch input 3 points Front PowerLED 3 color display Input power supply 100VAC Input range 100V 240VAC 50VA External RGB output Analog RGB output 15 pin HD SUB Female connector About 3 6kg 1 Ineludes the attachments except cables CONTEC PC PT020 Hardware Manual 7 2 Overview Installation Environment Requirements Table 2 2 Installation Environment Requirements Ambient specifications Line noise Line noise AC line 2kV resistance Signal line 1kV EN61000 4 4 L
8. d at the specified voltage Use of any other voltage level may cause fire or electrical shock This device must be properly grounded Users should never disassemble or modify this device or exchange components This can cause fire or electrical shock In addition the manufacturer is unable to repair products that have been modified by the user Procedures that could result in serious injury or loss of human life should never be performed from a touch panel Use system design methods that can guard against input errors CONTEC PC PT020 Hardware Manual 3 1 Before Using the Product An CAUTION Do not use or store the product in a location such as extremely high or low temperature rapid temperature changes and the place which receives a strong ultraviolet ray Example Exposure to direct sun In the vicinity of a heat source Do not use the product in extremely humid or dusty locations It is extremely dangerous to use the product with its interior penetrated by water or any other fluid or conductive dust If the product must be used in such an environment install it on a dust proof control panel for example Avoid using or storing the device in locations subject to shock or vibration Do not use the product in the vicinity of devices that generate strong magnetic force or noise Such devices will cause this device to malfunction Do not use or store the product in the presence of chemicals To clean the PANECON
9. e treat it in accordance with the disposal regulations stipulated by your local government About VCCI class A FCC PART15 class A and EMC instruction class A incidental articles This product acquires the above mentioned standard and when an external speaker is used an enough margin might not be able to be secured In that case please install the ferrite core SEIWA E04SR200935A or interchangeable goods in the speaker connection cable Please shut after it wraps it twice near the connector with the ferrite core opened when you install it CONTEC PC PT020 Hardware Manual 5 1 Before Using the Product FCC PART 15 Class A Notice NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference at his own expense WARNING TO USER Change or modifications not expressly approved the manufacturer can void the user s authority to operate this equipment CONTEC 6 PC PT020 Hardware Manual 2 Overview 2 Overview Spe
10. evel3 IEC1000 4 4 Level 3 Static Contact discharge 4kV EN61000 4 2 Level 2 IEC1000 4 2 Level 2 electricity Atmospheric discharge 8kV EN61000 4 2 Level 3 IEC1000 4 2 Level 3 resistance Vibration Anti shaking 10 57Hz semi amplitude 0 075mm resistance One cycle 10 150 10 Hz of 1oct min test at 9 8 m s 1G between 57 an 150 Hz x 5 times in three X Y Z directions 40 minutes each JIS C0040 compliant IEC68 2 6 compliant Impact resistance Tested with 11 ms half sine wave at 98 m s 10G three times in each of three X Y Z directions JIS C0041 compliant IEC68 2 27 compliant Class D grounding previous class 3 grounding SG FG continuity Water proof and dust proof Whole frame IPX2 compatible in normal installation Screen IP65 2 1 When the total supply current of the USB connector exceeds 200mA the Operating temperature of use becomes 0 40 C Attaching cover for the main body 2 Please obtain the Attaching cover for the main body of appending to Water proof and dustproof Table 2 3 Power Installation Environment Requirements Power specifications Allowable instantaneous 17ms or less ACIN100V Io 100 average value AC2 0kV between input and FG 10mA 1 minute 50MO 600VDC IP Protection Ratings IP Protection Ratings indicate levels of protection against intrusion by solid foreign substances and water IP65 This product does not allow entry of dust into it It also does not a
11. fittings on the narrow square hole of the main body as shown in the following figure and push it in so that the PCMCIA card is covered Figure 4 4 Attaching the PCMCIA card removal prevention fittings lt 1 2 gt 3 Secure the fittings at the upper end with the provided screw Figure 4 4 Attaching the PCMCIA card removal prevention fittings lt 2 2 gt Back light exchange The backlight used in the LCD module has a limited life When it expires and requires replacement contact your retailer CONTEC 22 PC PT020 Hardware Manual 4 Hardware Setup Attaching the USB cable removal prevention clamps 1 Connect the USB cable Figure 4 5 Attaching the USB cable removal prevention clamps lt 1 3 gt 2 Tie the USB cables together using the provided clamp for preventing USB cables from being disconnected Figure 4 5 Attaching the USB cable removal prevention clamps lt 2 3 gt CONTEC PC PT020 Hardware Manual 23 4 Hardware Setup 3 Fix the USB cable removal prevention clamps to the main body as the following diagrams Figure 4 5 Attaching the USB cable removal prevention clamps lt 3 3 gt CONTEC 24 PC PT020 Hardware Manual 4 Hardware Setup Attaching the AC cable removal prevention clamps 1 Fix the AC cable removal prevention clamps Figure 4 6 Attaching the AC cable removal prevention clamps lt 1 4 gt 2 Connect the AC cable Figure 4 6 Attaching the AC cable remova
12. i z d E Geer AS _ d L La E Von Tree te a 71 a e o iS Des Ye D X Dust cover bundle Nas ie 32 6 hE mm Figure 2 2 Physical Dimensions CONTEC PC PTO20 Hardware Manual 10 3 Each Component Function 3 Each Component Function Component Locations Interface The lower side of the back POWER LAN Sw ACN voa comz com INK CACT USB RST SPK Poncia Leen TI TIO THI TIO TI I O SS Bottom side POWER SW AC IN VGA COM2 COM1 LAN USB RST SPK PCMCIA Front side Function switch POWER LED Figure 3 1 Component Locations CONTEC PC PT020 Hardware Manual 11 3 Each Component Function Table 3 1 Component Identification kass Joo CONTEC 12 PC PTO20 Hardware Manual 3 Each Component Function Component Identification Serial Port Interface COM1 COM2 The PANECON PC is equipped with two RS 232C compliant serial port connectors Serial Port 1 COMI and Serial Port COM2 Baud rate 50 115200bps Table 3 2 COM1 COM2 Serial Port Inter Connector Main unit connector D SUB 9 pin Male 1 5 No 4 40UNC SE e Inch screw 9000 6 9 Pin No Signal Function Direction 1 CD Carrier detection In 2 RD Recieved data In 3 TD Transmitted data Out 4 DTR Data terminal ready Out 5 GND Signal ground 6 DSR Data set ready M 7 RTS Request
13. l prevention clamps lt 2 4 gt CONTEC PC PT020 Hardware Manual 25 4 Hardware Setup 3 Tie the AC cables together using the AC cable removal prevention clamps from being disconnected Then push in the clamp and secure it firmly as shown with the arrow in the following figure so that the clamp does not move Figure 4 6 Attaching the AC cable removal prevention clamps lt 3 4 gt 4 Be sure that the AC cable is fixed Figure 4 6 Attaching the AC cable removal prevention clamps lt 4 4 gt CONTEC 26 PC PT020 Hardware Manual 4 Hardware Setup Attaching to the VESA Arm This product can be attached to the VESA standard 100mm arm When attaching the VESA arm note the following item Load Select the VESA arm of an enough load to the weight of this product Installation angle set it up to install the inclination of the back and forth on installation requirements For more details on the attaching method refer to the VESA arm s manual CONTEC PC PT020 Hardware Manual 27 4 Hardware Setup CONTEC 28 PC PTO20 Hardware Manual 5 List of Options 5 List of Options Manual IPC PTO20L S HMJ Hardware manual for IPC PTO20L S AC series Japanese IPC SH4CE4 SMJ Software manual Japanese IPC SH4CE4 SME Software manual English Other IPC SND 03 Desk stand Notes As the desk stand IPC SND 03 is not made of stainless steel care must be taken for its use environmen
14. llow entry of water from any direction even when directly squirted on with a strong pressure IPX2 The product is not badly affected by water dropped vertically from the top or within an angle of 15 degrees CONTEC 8 PC PT020 Hardware Manual 2 Overview Display Optical Specifications Table 2 4 IPC PT020LS AC 4E View angle Gs 90 Monochrome 60deg 70deg Horizontal o 90 90 60deg 70deg Display Monochrome Bright pect Display White 280cd m2 350cd m at center 1 1 The surface brightness is a numerical value in the display unit Brightness by which the touch panel is passed becomes the above mentioned numerical value of about 84 Contrast ratio CR Brightness at screen center with white displayed Brightness at screen center with black displayed Z Measurement direction Module Right Ge 90 Y Figure 2 1 Definition of viewable range An CAUTION The above optical specification data shows optical characteristics of the liquid crystal in the display the data does not represent the actual view on the display or its viewing angles CONTEC PC PT020 Hardware Manual 9 2 Overview Physical Dimensions IPC PTO20LS AC 4E 4 M4 TAP Ni 303 56 5 gt Maximum tapping length 5mm 100 E 6 ed oj ja y
15. ls Table3 5 USB connector E Pin No Signal name 1 5V 2 DATA 3 DATA 4 GND This product is bundled with the USB cable removal prevention cramp For how to mount the fittings refer to Chapter 4 Hardware Setup CONTEC PC PT020 Hardware Manual 15 3 Each Component Function External Speaker Output Terminal Connector type HSJ1456 010320 HOSIDEN Table 3 6 External Speaker Terminal Pin No Signal Remarks 1 GND Cl 2 Analog signal R Speaker Right O 3 Analog signal L Speaker Left 1pin GND 2pin R Analog signal 3 3pin L Analog signal Applicable connector Small jack of b3 5mm Full scale output level 1 0Vrms Typ Notes The built in speaker is connected to the analog signal L Therefore when using the speaker adjust the output balance between right and left by software if necessary If Jack is connected with the external speaker output terminal an internal speaker is turned off Touch Panel The PANECON PC is equipped with an analog touch panel that enables keyboard less mouse less Operations Refer to the software manual for details on how to use the touch panel Table 3 7 Touch panel specifications This product Detection method Analog resistive glass glass type Surface treatment i 4096 x 4096 emulated in 800 x 600 Operating load Min 0 2N Max 3N 1N 0 102kgf Operating lifetime 1 million touches mini
16. mum Load 1N 5 sec application Tip shape silicon rubber p10mmR125 CONTEC 16 PC PT020 Hardware Manual 3 Each Component Function Analog RGB I F Simultaneous dual screen display is enabled when an analog RGB display is connected to the Analog RGB I F of this product Table 3 8 VGA connector Connector type 15 pin HD SUB Female 5 1 S 84 if 900 0 o x me No 4 40UNC Inch screw 15 Signal a Signal Pin No Pin No name name Bl RED 9 VCC 2 GREEN 10 GND 3 BLUE 11 N C 4 N C 12 N C 5 GND 13 HSYNC 6 GND 14 VSYNC 7 GND 15 N C 8 GND Table 3 9 Analog RGB specifications Display Dot Clock Horizontal Vertical HSYNC VSYNC Dots Freguency Freguency Freguency Polarity Polarity 800 x 600 40 0MHz 37 9KHz 60 1Hz Negative Negative Notes The use of a liquid crystal display may cause disturbed images on the screen due to a resolution problem depending on the display to be connected The display resolution is 800 x 600 SVGA fixation CONTEC PC PT020 Hardware Manual 17 3 Each Component Function CONTEC 18 PC PTO20 Hardware Manual 4 Hardware Setup 4 Hardware Setup Hardware Setup Make sure that the power is switched off before you start the operation Do not remove any screws other than those explained here As for the following items be sure to setup 1 Attaching c
17. on of equipment and resources Understand the meanings of these labels to operate the equipment safely A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury or in property damage Handling Precautions z WARNING Do not use this product in the presence of flammable or corrosive gases This may lead to explosion fire or damage to equipment In the event of smoke or abnormal smells or sounds immediately turn OFF the power to this device disconnect the plug from the power outlet and contact the manufacturer Continued use could lead to fire or electrical shock Because of the danger of electrical shock or fire do not contact this device Other than the front touch panel while electrical current is present Never touch this device or connectors with wet hands This can cause electrical shock Do not allow this device to come into contact with foreign substances metal particles flammable substances liquids etc This can cause fire or electrical shock Do not place this device in an unstable location or use incomplete mountings This may cause the device to fall This device must be operate
18. over for the main body 2 Attaching the USB cable removal prevention clamps 3 Attaching the AC cable removal prevention clamps 4 Attaching the PCMCIA card removal prevention fittings CONTEC PC PT020 Hardware Manual 19 4 Hardware Setup Installation Requirements When installing this product vertically place the interface block at the bottom To maintain the ambient temperature within the installation environment requirement range provide a gap of 50mm or more between the main unit and any adjacent equipment Also use the product within an angle of 60 degrees as shown in the following figure 4 A Figure 4 1 Distances between the PANECON PC and Its Vicinity 15 60 Figure 4 2 Installation permitted angle of the main body CONTEC 20 PC PTO20 Hardware Manual 4 Hardware Setup Attaching the cover for this product 1 Loosen the screws of the main body as shown in the following figure Figure 4 3 Attaching cover for the main body lt 1 2 gt 2 Mount the bundled attaching cover for the main body by tightening the screws back ensuring that the cover contacts the body without any gap at the positions specified in the following figure Figure 4 3 Attaching cover for the main body lt 2 2 gt CONTEC PC PTO20 Hardware Manual 21 4 Hardware Setup Attaching the PCMCIA card removal prevention fittings 1 Insert the PCMCIA card 2 Hook the right catch of the
19. prior written consent of CONTEC CO LTD CONTEC CO LTD makes no commitment to update or keep current the information contained in this document The information in this document is subject to change without notice All relevant issues have been considered in the preparation of this document Should you notice an omission or any questionable item in this document please feel free to notify CONTEC CO LTD Regardless of the foregoing statement CONTEC assumes no responsibility for any errors that may appear in this document or for results obtained by the user as a result of using this product Trademarks Intel and Celeron are registered trademarks of Intel Corporation MS Microsoft and Windows are trademarks of Microsoft Corporation Other brand and product names are trademarks of their respective holder CONTEC ii PC PT020 Hardware Manual Table of Contents Check Your Package COP ly AAA AA ii Trad STH a r A ii Table of Contents ien ee EE AER iii 1 BEFORE USING THE PRODUCT 1 About the Broderie it EE KEE AiR ENEE EEEREN 1 LC De 1 Customer SUP POL tose zaseklo TEESE EN 2 KEE 2 Limited A a 2 Howto Obtain Service rosou 2 EE s NA na 2 Safety Me e 3 Safety Information dE EENEG 3 Handling Pre o NEEN ANEREN 3 2 OVERVIEW 7 o EN 7 External Dimensions eiii 10 3 EACH COMPONENT FUNCTION 11 Component Loca A atid 11 Component Identification uerge 13 Serial Part Interface GOM1 COM2 niaminini ar nav 13 ir LAV N EEN
20. rchandise Authorization to the distributor or the CONTEC group office from which it was purchased This warranty is not applicable for scratches or normal wear but only for the electronic circuitry and original products The warranty is not applicable if the device has been tampered with or damaged through abuse mistreatment neglect or unreasonable use or if the original invoice is not included in which case repairs will be considered beyond the warranty policy How to Obtain Service For replacement or repair return the device freight prepaid with a copy of the original invoice Please obtain a Return Merchandise Authorization number RMA from the CONTEC group office where you purchased before returning any product No product will be accepted by the CONTEC group without the RMA number Liability The obligation of the warrantor is solely to repair or replace the product In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from Safety Precautions Understand the following definitions and precautions to use the product safely CONTEC 2 PC PTO20 Hardware Manual 1 Before Using the Product Safety Precautions Understand the following definitions and precautions to use the product safely Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destructi
21. t CONTEC PC PT020 Hardware Manual 29 IPC PTO20LS AC 4E Hardware Manual IPC PTO20LS HME CONTEC CO LTD November 2008 Edition 3 9 31 Himesato Nishiyodogawa ku Osaka 555 0025 Japan Japanese http www contec co jp English http www contec com Chinese http www contec com cn No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD 11072008 04192007 Management No A 51 387 11102008_rev6 Parts No LYHC356
22. t clean the touch panel with saturated material It is recommended to dry it immediately after cleaning Use waste dedicated for cleaning lenses e g lens cloth to clean the touch panel in a lightly rubbing motion It is a characteristic of analog touch panels that their resistance may vary with changes to the ambient environment temperature and humidity and with their own aging resulting in the deviation of the detection point If this is the case calibrate the touch panel again to re set calibration data CONTEC PC PT020 Hardware Manual 1 Before Using the Product Burn in on TFT Display Burn in may occur if the same display is retained for a long time Avoid this by periodically switching the display so that the same display is not maintained for a long time Burn In Phenomenon characterized by a TFT display as a result of long time display of the same screen where a shadow like trace persists because electric charge remains in the LCD element even after the patterns are changed Life expectancy of components 1 Battery A lithium ion primary battery is used to back up the internal clock calendar and CMOS RAM The non energized backup time at 25 C is 10 years or more and at 60 C is 7 years or more 2 LCD backlight Display brightness decreases over time with use The operating lifetime of the backlight is 50 000 hours the time until the brightness is lowered to 50 of the initial value 3 Touch panel
23. to send Out 8 CTS Clear to send In 9 RI Ring indicator In CONTEC PC PT020 Hardware Manual 13 3 Each Component Function Ethernet LAN Table 3 3 Ethernet connector RJ 45 Connector type RJ 45 1 8 LINK ACT Pin No Singal name Function 1 TX Transmitted data output 2 TX Transmitted data output 3 RX Received data input 4 N C Not connected 5 N C Not connected 6 RX Received data input 7 N C Not connected 8 N C Not connected LED indicator LINK Green Indicates the LINK status ACT Orange Indicates that data is being transmitted received when flashing 14 CONTEC PC PTO20 Hardware Manual 3 Each Component Function PCMCIA PCMCIA PCMCIA compliant card slots are provided TYPE II x 2 TYPE III x 1 size Slot 1 Slot 2 Figure 3 2 Slot Numbers and Locations An CAUTION A type MI card should be inserted into slot 2 Incase of the CompactFlash Card please use the PCMCIA conversion adapter This product is bundled with the PCMCIA card removal prevention fittings For how to mount the fittings refer to Chapter 4 Hardware Setup Power Supply to the Card The voltage that can be used and the current capacity of each slot are as shown below Table 3 4 Power Supply to the Card Current capacity Max USB port The PANECON PC is eguipped with USB interface 2 channe
Download Pdf Manuals
Related Search