Promi-SD™ User Manual
Contents
1. Check the current SD status by entering the AT BTINFO command The SD status should display CONNECT STATUS OK AT BTINFO 01010 51076101010107 NS zES1 DIY pd 0010107 CSN VI OT D 0K O10 NIN On OHO OK 2 Release the current Bluetooth connection by entering ATH command Once disconnected successfully the SD returns the DISCONNECT message OK DISCONNECT 2 2 5 Automatic connection of two Promi SD Units Two SD units connect automatically when powered up For automatic SD connection first make a Bluetooth connection between two SD units Once Promi SD User Manual ver 1 7 24 www initium co kr connected the SD stores the 48 bit BD ADDR of its counterpart To expedite 48 bit BD_ADDR input operation the SD is designed to store the BD_ADDR of its latest counterpart 1 Set one SD to do INQUIRY SCAN and PAGE SCAN operation as directed in section 3 3 2 Set the other SD to connect to the SD in the previous step 3 Once connected successfully both SD units store the BD_ADDR of their counterpart in their internal Flash When desired release the connection as directed in section 3 4 4 Set the operating mode of one SD to MODE 1 by entering an AT BTMODE command as shown below AT BTMODE 1 OK 5 Set the operating mode of the other SD to MODE 2 by entering an AT BTMODE command as show below AT BTCANCEL OK AT BTMODE 2 OK 6 Turn both SD units power2. Trademark Acknowledgements The Bluetooth trademarks are owned by their proprietor and used by Initium Co Ltd under license Promi is a registered trademark of INITIUM Copyright Information The unauthorized copying of materials that are covered by copyright and other international proprietary or intellectual property rights is prohibited in most countries Initium Co Ltd recommends that the users of this equipment seek the necessary authorizations for copying material The instructions for use in the manual shall not be considered as an inducement to make illicit duplications of material Any duplication will be made at user s own risk Maintenance and Support Every care has been taken in the preparation of this manual if you detect any inaccuracies or omissions please inform us by contacting Intium s technical support Initium Co Ltd cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without any prior notice Limited Warranty Promi SD Initium Co Ltd warrants the original owner that the products delivered will be free from defects in material and workmanship for 90 days following the date of purchase This warranty dose not cover any damage attributable to erroneous installation of the product INITIUM S TOTAL LIABILITY IS LIMITED TO THE PRICE LICENSE FEE ACTUALLY Promi SD User Manual ver 1 7 38 www initium co kr
3. gt ON C OFF 3 Press Apply button 4 You will get Configuration has been applied message PromiWiN 5 Connection out 21 Connectiontin Device Name PSDv3a 120296 Current Mode Current Status PENDING Encryption Uart Setting Baud Rate 9600 StopBit One Stop Bit Parity E None Back to Standby status 6 Please CONFIRM that now the Promi SD is in MODE3 and PENDING status as in Red circle above If the Promi SD is in STANBY status connection WILL NOT Promi SD User Manual ver 1 7 www initium co kr 33 be made 7 Atthis stage Promi SD is DICOVERABLE amp CONNECTABLE MODE Get your Bluetooth CF cards or USB adaptors connected to this Promi SD now Then you finish to connect your Bluetooth devices to Promi SD Open you COM port of Serial Communication program to verify communication status Promi SD User Manual ver 1 7 34 www initium co kr 5 Optional Antennas 1 Dipole Antenna Part 0 2dBi Connector SMA Size 10cm 2 Patch Antenna w RF extension cable amp wall attachable nails Part No PSD00 00060 8 5dBi Including a 30cm RF extension cable Longer RF extension cable Part No PSD00 00061 1m length For 3m and longer length please ask it to our support initium co kr SMA connector Promi SD User Manual ver 1 7 www initium co kr 35 Part No PSD00 0
4. 7 50 www initium co kr Command Response Comments 1 AT lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt ATZ lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Drops all connections disable Inquiry 2 and Page scans Reset the bluetooth module 3 AT amp F lt cr gt lt cr gt lt If gt OK lt cr gt lt lif gt Reset to factory default state AT BTINQ lt cr gt 112233445 lt gt lt gt Inquiry nearby devices The OK at 5 FriendlyName Co the end means end of inquiry D lt cr gt lt lf gt gt 0 lt gt lt 5 5 FriendlyName Co 4 D lt cr gt lt If gt lt cr gt lt lf gt 112233445 5 FriendlyName Co D lt cr gt lt lf gt lt cr gt lt if gt OK lt cr gt lt lf gt ATD112233445566 lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Connect to the specified device lt cr gt lt If gt CONNECT If you want to enable Authentication 5 lt cr gt lt lf gt or and Encryption just set variable as 1 lt cr gt lt If gt ERROR lt cr gt lt If gt ATD lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Connect to the device that last lt cr gt lt If gt gt CONNECT succefully connected 6 lt cr gt lt If gt or lt cr gt lt If gt ERROR lt cr gt lt If gt AT BTSCAN lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Enable inquiry and page scans with 2 timeout of infinity AT BTSCAN n to lt cr gt lt cr gt lt lf gt OK lt cr gt lt lf gt Enable inquiry or Page scans
5. PAGE SCAN until it has a connection from other Bluetooth device Once connected your SD returns CONNECT message You can use AT BTCANCEL to cancel this operation This AT command has the same effect of AT BTSCAN 3 0 Promi SD User Manual ver 1 7 45 www initium co kr AT BTSCAN n to lt cr gt Function You can force your SD to do INQUIRY SCAN or PAGE SCAN Response lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt If gt CONNECT lt cr gt lt lf gt or lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt If gt ERROR lt cr gt lt lf gt Description To make SD to be Discoverable and Connectable from other Bluetooth devices you should set its INQUIRY SCAN and PAGE SCAN To make your SD do INQUIRY SCAN only you should set n as 1 To make your SD do PAGE SCAN only you should set n as 2 When n is set to 3 your SD does INQUIRY SCAN and PAGE SCAN alternately Here to indicates the time out interval of INQUIRY SCAN and PAGE SCAN operations If you set to to 0 your SD does INQUIRY SCAN and PAGE SCAN until it has a connection from other Bluetooth device Your SD returns CONNECT message when it is connected from other Bluetooth device within the given time out intervals Otherwise it returns ERROR message AT BTSCAN BD_ADDR to lt cr gt Function Wait Bluetooth connection from a device with given BD_ADDR Response lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt l
6. PAID BY PURCHASER TO INITIUM FOR THE PRODUCT WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED IN NO EVENT SHALL INITIUM OR ITS LICENSOR AND SUPPLIERS BE LIABLE FOR ANY INDIRECT INCIDENTAL OR CONSEQUENTIAL LOSSES OR DAMAGES OF ANY NATURE WHATSOEVER INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE LOSSES SUSTAINED BY YOU OR THIRD PARTIES SUCHAS LOSS OF BUSINESS LOSS OF PROFITS BUSINESS INTERRUPTION OR PERSONAL INJURY EVEN IF INITIUM OR ITS LICENSORS OR SUPPLIERS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES This warranty does not cover replacement of products damaged by abuse accident misuse neglect alteration repair disaster improper installation or improper testing Promi SD User Manual ver 1 7 39 www initium co kr 9 About this Manual This manual is available in a printable PDF version on line and on the CD enclosed in the Promi SD product package For additional support related to Promi SD and this document contact INITIUM via INITIUM Co Ltd 716 Kumgang Hitech Valley 133 Sangdaewon Jungwon Sungnam Kyunggi 462 120 Korea Tel 82 31 777 5703 Fax 82 31 777 5704 OR www initium co kr OR Email info initium co kr Promi SD User Manual ver 1 7 40 www initium co kr Appendix A Power Adaptor Specification Manufacturer Anam Instruments Inc Emerald B D 7F 1042 Hogea dong Dongan gu Anyang Korea Tel 82 31 347 6140 F
7. Pending status in MODES to be discoverable connectable To be in Pending status please click MODE3 and press Apply button Uart Baud Rate a500 v Parity No Parity StopBit 1 Device Name PSDv3a 120296 ee Security Option I Authentication I Encryption Password ON OFF Apply Promi SD User Manual ver 1 7 19 www initium co kr 3 4 Now jobs for SD02 are finished Detach SD02 from your computer 3 5 Attach SD01 to your computer 3 6 Restart Promi WIN 3 7 Select Device Setting icon in the list control box and select MODE2 in Operation Mode and apply PromiWIN PromiWIN i Default To see default configuration of Promi SD Information r Operation Mode MODE Standby status for Bluetooth connection 2 MODE1 This Promi SD shall connect to the last connected device only Device Setting C MODE3 Allow any Bluetooth devices discover connect to this Promi SD You must be in Pending status in MODES to be discoverable connectable To be in Pending status please click MODES and press Apply button Connection out EE Baud Rate 9600 v Parity No Parity StopBit 1 a p Security Option Device Name PSDv3a 120296 Connection in I Authentication I Encryption Signal Password eae gt C OFF Apply 3 8 Now detach SD01 from your computer 3 9 Make sure that power to Both SD01 and SD0
8. co kr 2 1 3 Let s make Auto Connection between SD01 and 2 3 1 With SD02 which is still attached to your computer in Connection out page press DISCONNECT button at the bottom to release the connection for a while SD02 remembers who was the last connected device even after Disconnected PromiWIN Config COM Port 1 Promi WIN DD Information Z Device Setting Connectiontout 21 Connectiontin BaudRate 9600 Parity Bit No Parity StopBit 1 Search Result DEVICE_ADDRESS 60 6B 53 66 65 55 66 96 62 65 20 81 DEVICE NAME CoD IniCarkit II 266468 dj456 S N SG2AJ211KU3S 140680 00 0B 53 12 02 79 PSDu3a 120279 661F 66 Search 10 Define the number of nearby devices to be searched Disconnect Drop the Connectio 000853120279 Connect to Specified devices 3 2 Now Status LEDs of 5002 becomes Orange as well as SD01 as they are disconnected 3 3 Select Device Setting icon in the list control box and select MODE in Operation Mode and apply gt PromiWin Promi WIN D Information P Device Setting Connection out B Connection in Default To see default configuration of Promi SD Operation Mode C MODED Standby status for Bluetooth connection MODE2 This Promi SD shall be connected from the last connected device only C MODES Allow any Bluetooth devices discover connect to this Promi SD You must be in
9. refer to our Promi MSP providing all the features of RS485 Product line Model Name Part No Spec Promi SD101 PSDO00 10100 Class 2 Output Power 2 5mW 4dBm 5V DC power supply Rechargeable Li poly Battery internal w Power Adapter w Setup Software amp manual on CD Promi SD202 PSDO00 20200 Class 1 Output Power 63mW 18dBm 5V DC power supply w o Battery amp Power Adapter w Setup Software amp manual on CD w USB Power Cable amp DC Power Cable Optional 5V Power Adapter Promi SD User Manual ver 1 7 5 www initium co kr Fig 1 1 1 A CD ROM inclusive a setup software Promi WIN and user manual Fig 1 1 2 Optional Power Adaptor Part no PSD00 00010 Fig 1 1 3 USB Power Adaptor Part no PSD00 00020 You may use USB port to supply power to Promi SD using this USB power cable Promi SD User Manual ver 1 7 6 www initium co kr Fig 1 1 4 DC Power Cable Part no PSD00 00030 Red colored line of DC power cable is for Promi SD User Manual ver 1 7 7 www initium co kr 1 2 External View Promi SD Dimensions 60 x 26 x 16 mm POWER LED STUB ANTENNA INITIUM CMSA _ P N PSD00 00040 6 Nan Promi SD20 Bee toor Sersi Adaptar 0 STATUS LED Figure 1 2 1 Promi SD top view ON OFF SWITCH L HARD RESET SWITCH Figure 1 2 2 Promi SD right side view DC Connector Figure 1 2 3 Promi SD left
10. second Inquiry Timeout default 30 Unit second BD address of last connected device Promi SD User Manual ver 1 7 55 www initium co kr
11. side view Please refer to the 1 5 Power Supply section for Promi SD power options Promi SD User Manual ver 1 7 8 www initium co kr 1 3 LED Indicator The Promi SD STATUS LED indicates the following Amber STATUS LED indicates standard mode on Promi SD power up Green STATUS LED indicates Promi SD is connected to another Bluetooth device Green flashing STATUS LED every second indicates Promi SD INQUIRY operation Green flashing STATUS LED every 3 seconds indicates Promi SD INQUIRY SCAN or PAGE SCAN operation Amber POWER LED of Promi SD101 indicates battery is being charged Green POWER LED of Promi SD101 indicates battery is fully charged Green POWER LED of Promi SD202 indicates power is being supplied 1 4 Block Diagram Promi SD AC 110V 220V Adaptor 5V 1 5 Power Supply Promi SD User Manual ver 1 7 9 www initium co kr Power may be supplied by following ways Power via a standard AC plug DC adapter p n PSD00 00010 Power via USB power cable p n PSD00 00020 Power via DC power cable p n PSD00 00030 Power via pin 9 of D SUB connector Promi SD101 can be recharged by 4 ways above O e Figure 1 5 1 DC plug polarity Promi SD101 Class2 5V 10 500mA minimum Promi SD202 Class1 4V 12V 150mA minimum Current Consumption Data at different speeds of serial communications Current Consumption Battery Life Condition of Baud Rate mm Promi
12. 0062 Anchor Support This will be needed if there is a need to attach the Patch antenna to the wall Distance Data between Promi SD s when Optional Antennas are used Model no Antennas for two Promi SD units Max Distance Promi SD101 Default Antenna Default Antenna 30 meters Default Antenna Dipole Antenna 50 meters Dipole Antenna Dipole Antenna 80 meters Patch Antenna Dipole Antenna 150 meters Patch Antenna Patch Antenna 300 meters Promi SD202 Default Antenna Default Antenna 120 meters Default Antenna Dipole Antenna 150 meters Dipole Antenna Dipole Antenna 200 meters Patch Antenna Dipole Antenna 400 meters Patch Antenna Patch Antenna 1 200 meters Promi SD User Manual ver 1 7 36 www initium co kr 6 For Multi Serial Connections 6 1 Promi MSP For multiple serial connections we recommend Promi MSP Promi MSP has 7 default Bluetooth connections and can be expanded to up to 14 connections More information on Promi MSP can be found in its User Manual at www initium co kr lt Fig 7 1 1 Promi MSP gt Promi SD User Manual ver 1 7 37 www initium co kr Legal Notice About this Document This document provides introductory instructions on how to set up and manage Promi SD within your networking environment Should you require more information please refer to Initium website at http www initium co kr
13. 2 are supplied With two of the SD01 and SD02 turn off both using Switch on the side of its body Then turn on again Both SD01 and SD02 almost at the same time Now you will see Green Status LEDs on both units SD01 and SD02 will be connected automatically whenever if configuration is not changed Promi SD User Manual ver 1 7 20 www initium co kr 2 2 Using a Terminal Program Promi SD units are easily controlled and configured via PromiWIN Likewise functions are accomplished via any terminal program such as HyperTerminal AT command sets supported by Promi SD add sophistication to Promi SD control 2 2 1 Connecting Promi SD to host For SD use follow the simple instructions below Connect an SD to a host serial port Then turn on the SD Check the STATUS LED color Amber indicates standard mode Execute any terminal program and activate Local Echo gt A O N Configure the host serial port to match the SD unit configuration The SD default configuration is 9600 bps Baud 8 Data bit No Parity 1 Stop bit and H W flow control 5 Enter AT command at the prompt An SD OK reply indicates proper operation 2 2 2 Making the first Promi SD Bluetooth connection As stated before Bluetooth wireless connections can be made with any other Bluetooth device supporting Bluetooth SPP Serial Port Profile For Bluetooth wireless connections to an SD first make another SD Di
14. 4 2 2 6 AT command vs Operational Status 26 3 Technical Specifications 7 3 1 Default Serial SCtllOS eo mssmekesnesanssr cade ssnanns ks ken na kANRNA KRA KSK KANNA RANNAN EENAA KA KAN 21 3 2 Power CONSUM PU ON slossusssvssssie hie ei dess ken ee dears k ns E eee 21 3 3 Environmental serne E AAA RN RANA ARA SA 28 28 3 5 Maximum distance between Promi SD S sosse 29 4 650 000 Promi SD User Manual ver 1 7 3 www initium co kr 4 1 ON OFF of Hardware Flow 60 30 4 2 Enabling Disabling of Response Signals nmnsnsssssesrssseerssseenssseer anses rss sees snar er sne eran 31 OK CONNECT DISCONNECT amp 31 4 3 For DCE sciis ea a ea d ON 32 32 Hardware 4 4 4 5 How to get Bluetooth CF cards connected to 1 80 32 5 Optional Antennas 64 35 6 For Multi Serial Connections 0 37 37 6 1 7 Legal Notice ssmnssssssssssssennssnnnnrnnnnnnn sn nn n rr nn nn nn nn 38 9 About this 3 40 Appendix A Power Adaptor Specification 41 Appendix B AT command 56 44 Promi SD User Manual ver 1 7 4 www initium co kr 1 Product Description 1 1 About Promi SD Promi SD is developed for long range easy to install low cost wireless serial communications Provided is point to point wireless connection without standard RS232 cables For point to multipoint connections please
15. ADDR Response lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt If gt CONNECT lt cr gt lt lf gt or lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt If gt ERROR lt cr gt lt lf gt Description After getting BD_ADDRs you can make connection to other Bluetooth device by using this AT command Once you input this command SD tries to connect the Bluetooth device with the given BD_ADDR for 5 minutes The connection failure happens when a Bluetooth device with the given BD_ADDR is not in PAGE SCAN mode or is already connected to other Bluetooth device ATD lt cr gt Function Make connection with a Bluetooth device connected most recently Response lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt If gt CONNECT lt cr gt lt lf gt or lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt If gt ERROR lt cr gt lt lf gt Description If you execute this AT command your SD make connection with a Bluetooth device which your SD connect most recently To make this AT command work successfully there should be at least one successful connection to the other Bluetooth you want to connect AT BTSCAN lt cr gt Function Make your SD do INQUIRY SCAN and PAGE SCAN alternately Response lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt If gt CONNECT lt cr gt lt lf gt Description You can force your SD to do INQUIRY SCAN or PAGE SCAN alternately with this AT command Your SD does INQUIRY SCAN and
16. Baud Parity StopBit as the setting of attached SD02 9600 No OneStopBit is default setting of all of Promi SDs 2 4 Press OK button 2 5 Select the Connection out icon in the list control box and click the SEARCH button Promi SD User Manual ver 1 7 17 www initium co kr PromiWIN 1 r Search Result Information DEVICE ADDRESS DEVICE NAME CoD 00 0B 53 00 00 DF PSDu3a 6886DF 8891F 68 Z 00 00 F0 90 18 E4 Anycall bt 220204 88 88 53 28 88 75 Proni MSP SW2 828308 Device Setting 00 0B 53 20 00 63 Proni MSP 020300 00 90 02 05 2C 81 Anycom BT YUJINKIM 10616C Connection out 8 AMANNMAN s Cancel Search jio 4 Define the number of nearby devices to be searched Connection in Connect to Connect to Specified devices Disconnect Drop the Connection 2 6 Search SD01 from the searched list Device Address of SD01 can be found on the back side of SD01 If you find SD01 press Cancel button to finish searching Make sure that Status LED of SD01 is still blinking in Green color 2 7 Please select SD01 from the searched list then press CONNECT TO button 2 8 You will get Successful Connection message Connect FR Successful Connection 2 9 Now Status LEDs on Both SD01 and SD02 are Green which means they are connected 2 10 Do not detach SD02 from your computer yet we will go to next stage for Auto connection Always connection Promi SD User Manual ver 1 7 18 www initium
17. DDR Name Mode Status Auth Encryp lt cr gt lt If gt lt cr gt lt If gt OK lt cr gt lt If gt Description When you enter this AT commands at a host terminal your SD returns its device information and status to a host It encompasses BD ADDR user friendly name operating mode operating status and authentication encryption status Especially when the operating status is PENDING it means your SD is busy in processing AT BTINQ ATD or AT_BTSCAN When Authentication or Encryption feature is activated the corresponding parameter has value of 1 AT BTLPM n lt cr gt Function Set Bluetooth Low power consumption mode Response lt cr gt lt lf gt OK lt cr gt lt lf gt Description To minimize power consumption your SD supports Bluetooth PARK mode When you set n as 1 your SD uses PARK mode Using PARK mode might cause extra data transmission delay in some cases AT BTSD lt cr gt Function Return the list of secured devices Response lt cr gt lt lf gt BD_ADDR lt cr gt lt lf gt lt cr gt lt If gt BD_ADDR lt cr gt lt lf gt lt cr gt lt If gt BD_ADDR lt cr gt lt lf gt lt cr gt lt lf gt OK lt cr gt lt lf gt Description Your SD can pair up to 5 Bluetooth devices Upon receiving this AT command your SD returns all the BD_ADDRs of the previously paired Bluetooth devices AT BTCSD lt cr gt Function Delete the info of all the paired devices stored in your SD Response lt cr
18. FIG baudrate parity st opbit handshaking lt cr gt lt cr gt lt lf gt OK lt cr gt lt lf gt Sets the configuration of UART interface Possible values are baudrate 1200 4800 9600 19200 38400 5760 0 or 115200 parity N o parity E ven parity or O dd parity stop or 2 Handshaking 1 or 0 If 1 hardware handshaking will be used If 0 handshaking function of Promi SD will be turned off AT SETESC nn lt cr gt AT PINQ lt cr gt lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt lf gt OK lt cr gt lt lf gt Sets the escape sequence character nn should be ASCII code Decimal and printable character Default escape charater is For Periodic Inquiry Promi SD will try to inquire nearby Bluetooth devices periodically and deliver the inquired Promi SD User Manual ver 1 7 53 www initium co kr result to Host To lease periodic inquiry function AT BTCANCEL Shows S register values S register command If you change the values of S register please reboot Promi SD ATSnn mm lt cr gt To change ATSnn register value ATSnn To check current ATSnn register value Stream UART policy Default 0 If set as 0 throughput is the priority if set as 1 Latency is the priority Enable Remote name query default 1 Get BDaddress and device name during Inquiry If set as 0 only get BD address Inquiry time can be faster Defau
19. INITIUM Promi SD User Manual Version 1 7 by Bluetooth Revision History User Manual of Promi SD Version Changed Contents Date 1 1 Draft version 01 02 2003 1 2 Added Technical Specifications Troubleshooting 06 14 2003 1 3 Amended Power Consumption data of Promi SD101 102 202 06 24 2003 1 4 Amended PromiWIN software interface 07 14 2003 1 5 Added feature of Promi SD version v3b 09 08 2003 1 6 Revised by modifying some errors in technical specifications 12 22 2003 1 7 Removed old information on model Promi SD102 07 22 2004 Firmware Hardware Version History V3b The latest version Model Name Firmware Hardware version version Promi SD101 PSDv3b 1 5 Promi SD102 PSDv3b 2 0 Promi SD202 PSDv3b 2 0 Hardware Handshaking AT command Available on off DTR DSR CDC Release Date N A Sept 8 2003 Available Oct 10 2003 Sept 8 2003 Note From Firmware version PSDv3b customers may choose whether to use hardware flow control using PromiWIN software If you have PSDv3b please use PromiWINver3 0b for configuration V3a Model Name Firmware Hardware Hardware DTR DSR CDC Release Date version version Handshaking Promi SD101 PSDv3a 1 5 Auto Detection N A Aug 11 2003 Promi SD102 PSDv3a 2 0 Available July 14 2003 Promi SD202 PSDv3a 2 0 July 30 2003 V2 series Old version Model Name Firmware Hardware Hardware Handshakin
20. If n 1 disable page and enable inquiry 8 If n 2 enable page and disable inquiry If n 3 enable both page and inquiry Scan will be performed during lt to gt Promi SD User Manual ver 1 7 www initium co kr 51 seconds 9 AT BTSCAN112233445566 to lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Will scan of only specifed device AT BTCANCEL lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt cancel the current pending operation 10 when the device is inquirying paging or scanning mode lt cr gt lt If gt OK lt cr gt lt If gt Drop from online mode to command 0 mode ATO lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Return to online mode if currently 0 being connected 13 ATH lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Drop the connection AT BTSEC Authentication Encryption lt cr gt lt lf gt OK lt cr gt lt If gt Same as AT BTAUTH 14 AT BTLAST lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Query the 00 8007055 of last a connected device AT BTMODE n lt cr gt lt cr gt lt If gt OK lt cr gt lt If gt Sets the mode of device If n 0 device operates at Standart mode which accepts all AT commaned supported If n 1 device operates at Master 16 mode which try to connect peer device If n 2 device operates at Slave mode which waiting for connection If n 3 device operates at always connectable mode 17 AT BTNAME Frie
21. SD101 Promi SD202 Promi SD101 9600bps 35 3 mA 40 mA 5 hrs 20 min 115200bps 40 mA 72 mA 4 hrs 30 min 1 6 Interface RS232 Bluetooth Promi SD User Manual ver 1 7 10 www initium co kr 1 6 1 RS232 Interface Promi SD has a 9 PIN DSUB female connector as shown below in Fig 1 7 1 Figure 1 7 1 9 PIN DSUB Female e The serial interface is RS232 DCE configured a DTE device can be connected e Baud rate 1200 115200 bps 230400bps for Promi SD102 202 ESD e Hardware flow control RTS CTS Pin Signal Direction 1 CD Output 2 TxD Output 3 RxD Input 4 DSR Input 5 GND 6 DTR Output 7 CTS Input 8 RTS Output 9 Vcc Input Table 1 7 1 Promi SD 9 PIN Specification Promi SD is designed to operate as DCE Data Communications Equipment To connect to DTE Data Terminal Equipment for example a PC or a laptop a Promi SD User Manual ver 1 7 11 www initium co kr straight cable must be used as in below CD 1 gt CD 1 TxD 2 RxD 2 RxD 3 lt TxD 3 DR 4 lt lt FM DTR 4 GND 5 __ GND 5 DTR 6 _ DSR 6 Promi SD DCE 3 LQ wajshg soH CTS 7 lt RTS 7 RTS 8 7 CTS 8 DTR DSR of Promi SD will be functioned for either Loop back operation or for full transfer Users may select a function of DTR DSR using AT command ATS14 Default value of ATS14 is 1 e ATS14 1 lt cr gt Defaul
22. TAGE 2 2 5 1 Primary to Secondary 3 KV 1 Second 2 2 5 2 Cut Off Current 10mA 2 2 6 EMI 2 2 6 1 Shall be designed to meet CLASS B Limit of FCC part 15 2 2 6 2 Shall be designed to meet EN 55022 2 2 7 SAFETY 2 2 7 1 UL amp cUL UL1950 2 2 7 2 TUV CE EN60950 2 2 7 3 ek mark K60950 2 2 7 4 CB QAS CCIB PSE 2 3 GENERAL CHARACTERISTICS 2 3 1 OPERATING TEMPERATURE RANGE 0 C to 35 C at 100 Load condition 0 C to 40 C at 90 Load condition 2 3 2 OPERATING HUMIDITY 15 to 80 RELATIVE HUMIDITY 2 3 3 STORAGE TEMPERATURE 20 C to 85 C 2 3 4 STORAGE HUMIDITY 90 RELATIVE 2 3 5 BURN IN PROCESS 2 3 5 1 All unit shall be subjected to burn in process of mass production 2 3 5 2 TEMPERATURE 30 5 C 2 3 5 3 LOAD CONDITION 2A Promi SD User Manual ver 1 7 42 www initium co kr 2 3 5 4 INPUT VOLTAGE 110 220 Vac 3 MECHANICAL CHARACTERISTICS 3 1 DIMENSIONAL SIZE LENGTH 66 mm WIDTH 48 5 mm HIGHT 35 mm 3 2 OUTPUT CABLE CABLE LENGTH 1850 50 Promi SD User Manual ver 1 7 43 www initium co kr Appendix B AT command sets The following AT command sets are supported by Promi SD Here lt cr gt represents carriage return of ASCII Code 0x0D and lt If gt represents line feed of ASCII Code 0x0A AT lt cr gt Function Check the presence of your SD Response lt cr gt lt lf gt OK lt cr gt lt lf gt or lt cr gt lt If gt ERROR lt cr gt lt lf gt Descript
23. ax 82 31 347 7019 www anamic co kr Manufacturer s Model Name AP1015 1 STANDARD FEATURES 1 1 1OWATT AC DC SWITCHING MODE ADAPTOR 1 2 WALL MOUNT DESIGN 1 3 100 240Vac UNIVERSAL VOLTAGE INPUT 1 4 5V 2A REGULATED OUTPUT 1 5 SHORT CIRCUIT PROTECTION 1 6 DESIGN TO MEET CLASS B LIMIT OF EN55022 AND FCC PART 15 1 7 VACUUM IMPREGNATED TRANSFORMER 1 8 100 BURN IN PROCESS 2 ELECTRICAL CHARACTERISTCS 2 1 INPUT CHARACTERISTICS 2 1 1 AC INPUT VOLTAGE 2 1 1 1 Nominal input voltage 110 220 Vac 2 1 1 2 Rated input voltage range 100 to 240 Vac 2 1 1 3 Operating input voltage range 90 to 264 Vac 2 1 2 AC INPUT FREQUENCY 2 1 2 1 Nominal input frequency 50 60 Hz 2 1 2 2 Rated input frequency 47 63 Hz 2 1 3 AC INPUT CURRENT MAX 0 3 A RMS at 90 Vac 2 2 OUTPUT CHARACTERISTICS 2 2 1 DC OUTPUT Promi SD User Manual ver 1 7 41 www initium co kr OUTPUT LOAD OUTPUT OUTPUT VOLTAGE 2 2 1 1 Specified output regulation limit includes line regulation and load regulation 2 2 1 2 Continuous output shall not exceed 10 W 2 2 1 3 Ripple and noise is measured at the end of output connector with 2OMHz oscilloscope bandwidth 2 2 1 4 A 22uF Electrolytic capacitor and a 0 22uF Ceramic capacitor should be connected in parallel with output load 2 2 2 EFFICINCY Minimum 70 at 2A load condition 2 2 3 SHORT CIRCUIT PROTECTION CYCLING 2 2 4 NO LOAD OPERATION NO DAMAGE 2 2 5 DI ELECTRIC WITHSTANDING VOL
24. fore to maximize battery life the SD INQUIRY SCAN and PAGE SCAN is set to disabled in manufacture Therefore to make the SD Discoverable INQUIRY SCAN and Connectable PAGE SCAN these operations must be manually activated 1 Check the SD status by entering a AT BTINFO command AT BTINFO 01010 51076101010107 CSI ats 20 0000950 0 OK 2 Enter the AT BTSCAN command The SD will start INQURY SCAN and PAGE SCAN operation During the process the SD will flash twice every 3 seconds until it is connected to another Bluetooth device AT BTSCAN OK 3 Try Bluetooth connection to the SD from the other Bluetooth device Once connected the first SD will return the CONNECT message and the STATUS LED will display a continuous green without flashing AT BTSCAN OK CONNECT 2 2 4 Releasing the existing Bluetooth connection Once connected successfully the SD becomes transparent to any serial applications on hosts Data may be transferred within the radio range of the Promi SD User Manual ver 1 7 23 www initium co kr SD According to SD terminology this operating status is called ONLINE STATUS In ONLINE STATUS all AT commands are treated as characters and are ignored by the command interpreter of the SD Therefore to escape from ONLINE STATUS enter escape string 1 Transition from ONLINE STATUS to STANDBY STATUS by entering string to the SD
25. g DTR DSR version version Promi SD101 PSDv2h 1 0 Manual N A Promi SD102 PSDv2i 2 0 Auto Detection Available for Loop back Promi SD202 PSDv2h 2 0 Auto Detection Available for Loop back Promi SD User Manual ver 1 7 www initium co kr Contents 1 Product Description ss sss serrmearrmearrmearrer D 1 1 About PROMISSD PM loose rorskeirs ora nene rk ker ee ieee ieee KEN SERA NA KA KRA NAR HEK nei ae 5 1 2 External 8 EANA KR ARRANA 9 1 44 Block Die ream seee teed eee AS ade a 9 1 5 Power SUP PlY gsrsiidsbernss une ieee iti Neale ee at nae ares nad Gaeta enna 9 1 6 Interface RS232 BlIUGtOOth ssssmsssssssssrerssseerssseersssrersssre rss sars sr ss r AR RAR KR RASK KR RASK Kn sa 10 1 6 1 RS232 Interface 11 1 6 2 Bluetooth Interface 13 2 Configuration 2 1 Using Promi WIn 14 2 1 1 Let s make SD01 to be discoverable connectable 15 2 1 2 Let s make SD02 to search SD01 and connect to 17 2 1 3 Let s make Auto Connection between SD01 and SD02 19 2 2 Using a Terminal Program sssssssesssssrerssssrersssesrrs sens ss arr sr ass r sr RAR AR RAKA KR RSKR KR RASA KR RR SRK Rn nn 21 2 2 1 Connecting Promi SD to host 21 2 2 2 Making the first Promi SD Bluetooth connection 21 2 2 3 Making Promi SD do INQUIRY SCAN and PAGE SCAN 22 2 2 4 Releasing the existing Bluetooth connection 23 2 2 5 Automatic connection of two Promi SD Units 2
26. gt lt lf gt OK lt cr gt lt lf gt Description This AT command just deletes the info of paired devices stored on SD s Flash memory To delete the same info resides on SD s RAM you have to do software reset or hardware reset Promi SD User Manual ver 1 7 49 www initium co kr AT BTFP n lt cr gt Function Force your SD to generate passkey automatically Response lt cr gt lt lf gt OK lt cr gt lt lf gt Description Once paired your SD uses the stored link key By using this AT command you can make Bluetooth connection with a new link key When n is set to 1 your SD newly generates a link key during connection process AT UARTCONFIG baudrate parity stopbit handshaking lt cr gt Function Configure the serial port of your SD Response lt cr gt lt lf gt OK lt cr gt lt lf gt Description By using this AT command you can reconfigure the serial port of your SD You can set baudrate parity stopbit To make this command result active you should do soft reset or turn off on your SD The following values are permitted for each parameter e Baudrate 1200 2400 9600 19200 38400 57600 or 115200 230400 only for Promi SD102 202 ESD e Parity No parity E Even parity or O Odd parity e Stopbit or 2 e Handshaking or 0 If 1 hardware handshaking will be used If 0 handshaking function of Promi SD will be turned off Full AT commands set Promi SD User Manual ver 1
27. information please contact support initium co kr 4 4 Hardware Reset For Hardware reset press the button on the right side of the Promi SD unit with a narrow tool such as a ball point pen HARD RESET SWITCH 4 5 How to get Bluetooth CF cards connected to Promi SD If you are using Bluetooth CF cards or USB adaptors from other manufacturers please use PromiWIN software of latest version which will be more familiar to consumers PromiWIN can be downloaded from our website at http www initium co kr english download htm 1 In PromiWIN version3 start and go to the Device Setting menu 2 Select MODE3 to allow any Bluetooth device can discover and connect to this Promi SD Promi SD User Manual ver 1 7 32 www initium co kr PromiWIN PromiWIN s7 Information P Device Setting Connection out 2 Connection in Default To see default configuration of Promi SD Operation Mode MODED Standby status for Bluetooth connection MODE1 This Promi SD shall connect to the last connected device only MODE2 This Promi SD shall be connected from the last connected device only You must be in Pending status in MODES to be discoverable connectable To be in Pending status please click MODES and press Apply button Uart Baud Rate 9600 Parity No Parity StopBit 1 Md Device Name PSDv3a 120296 F Authentication P Encryption Signal Password
28. ion In standard mode you can check whether your SD is connected to a host correctly by using this AT command ATZ lt cr gt Function Do soft reset Response lt cr gt lt lf gt OK lt cr gt lt lf gt or lt cr gt lt If gt ERROR lt cr gt lt lf gt Description You can do soft reset by using this AT command When your SD is already connected to the other device it disconnects the connected device You can halt the current ongoing operation by using this command AT amp F lt cr gt Function Restore the default configuration of your SD Response lt cr gt lt lf gt OK lt cr gt lt lf gt or lt cr gt lt If gt ERROR lt cr gt lt lf gt Description You can restore the default configuration of your SD by executing this AT command AT BTINQ lt cr gt Function Search INQUIRY other Bluetooth devices nearby Response lt cr gt lt lf gt BD_ADDR Device Name Class of Device lt cr gt lt lf gt lt cr gt lt If gt BD_ADDR Device Name Class of Device lt cr gt lt lf gt lt cr gt lt If gt BD_ADDR Device Name Class of Device lt cr gt lt lf gt lt cr gt lt lf gt OK lt cr gt lt lf gt Description This command is used to inquiry other Bluetooth devices nearby The INQUIRY process is carried out during the predefined time duration 30 Promi SD User Manual ver 1 7 44 www initium co kr seconds The maximum number of INQUIRY result is 10 ATD BD ADDR lt cr gt Function Make connection with the given BD
29. lt 1 ATS10 1 lt cr gt Enabling all of the response messages OK CONNECT DISCONNECT and ERROR ATS10 0 lt cr gt Disabling all of the response messages OK CONNECT DISCONNECT and ERROR ATS10 lt cr gt To see current status of ATS10 Enable Escape default 1 Escape sequence character enable change from on line mode to command mode If set to 0 transmission speed can be improved Clear UART buffer at Disconnect default 0 If set to 1 when disconnected data stored in Promi SD will be removed Enable CDC accept default 0 If set to 0 Promi SD will use CDC signal to let Host know Bluetooth connection status Promi SD User Manual ver 1 7 54 www initium co kr If set to 1 Promi SD will accept CDC signal from other peer DCE configured Bluetooth device ATS14 1 lt cr gt Users may use DTR DSR lines for communications ATS14 0 lt cr gt Users may use DTR DSR lines for Loop back only Default value of ATS14 is 0 ATS15 1 lt cr gt If users set ATS15 1 users may use DTR signal to disconnect Bluetooth connection If ATS15 1 and DTR signal is changed from state ON to OFF your connection will be disconnected ATS15 0 lt cr gt If ATS15 0 users may NOT use DTR signal to disconnect the Bluetooth connection Maximum number of inquiry result default 10 Error Code for last occurred error Users can not change this value Page Timeout default 300 Unit
30. lt cr gt lt lf gt OK lt cr gt lt lf gt Description Your SD has 4 different operating mode According to the current operating mode you set your SD behavior differently n 0 This means your SD is in MODE 0 MODE 0 is the default configuration n 1 In MODE 1 your SD will try to make connection to most recently connected Bluetooth device n 2 In MODE 2 your SD will wait connection from most recently connected Bluetooth device n 3 IN MODE 3 your SD does INQUIRY SCAN and PAGE SCAN alternately AT BTNAME FriendlyName lt cr gt Function Assign user friendly device name to your SD Response lt cr gt lt lf gt OK lt cr gt lt lf gt Description You can assign your SD user friendly name by using this AT command With the assigned name you can distinguish your SD easily from other Bluetooth devices Up to 32 characters are permitted as user friendly name AT BTKEY nnnn lt cr gt Function Change the passkey Response lt cr gt lt lf gt OK lt cr gt lt lf gt Description When the authentication is enabled in your SD you should assign passkey Two Bluetooth devices which are to be connected should have the same passkey The default passkey of your SD is 1234 You can assign maximum 16 alphanumeric characters as a passkey Promi SD User Manual ver 1 7 48 www initium co kr AT BTINFO lt cr gt Function Return the internal status of your SD Response lt cr gt lt If gt BD A
31. mes transparent to any host applications which use serial ports ATH lt cr gt Function Release the current Bluetooth connection Response lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt lf gt DISCONNECT lt cr gt lt lf gt Description This AT command can be used for disconnecting the existing Bluetooth connection AT BTSEC Authentication Encryption lt cr gt Function Set Bluetooth authentication or encryption features selectively Response lt cr gt lt If gt OK lt cr gt lt If gt Description By using this AT command you can set authentication or encryption feature of your SD during Bluetooth connection process Once you set authentication or encryption features your SD stores its status To release authentication or encryption features you set you should use this AT commands or do soft reset To enable authentication or encryption set authentication or encryption parameter as 1 Otherwise set either of them as 0 Promi SD User Manual ver 1 7 47 www initium co kr AT BTLAST lt cr gt Function Return BD ADDR of the Bluetooth device to your host which your SD is connected most recently Response lt cr gt lt If gt BD ADDR lt cr gt lt If gt lt cr gt lt lf gt OK lt cr gt lt If gt Description You can use this AT command if you need to refer the BD ADDR of most recently connected Bluetooth device AT BTMODE n lt cr gt Function Set the operating mode of your SD Response
32. ndlyName lt cr gt lt cr gt lt If gt OK lt cr gt lt lf gt Sets the friendly name of this unit AT BTKEY nnnn lt cr gt lt cr gt lt lf gt OK lt cr gt lt lf gt Sets the Passkey of this unit e Up to 16 characters AT BTINFO lt cr gt lt cr gt lt lf gt 112233445 Retrieve local device information 566 FriendlyName including BD address Friendly name Mode State Authent mode of device internal operation ication Encryption lt cr gt lt lf gt lt cr gt lt lf gt OK lt cr gt lt lf gt state and status of authentication and encryption features Promi SD User Manual ver 1 7 www initium co kr 52 AT BTLPM n lt cr gt lt cr gt lt lf gt OK lt cr gt lt lf gt Enable or disable the low power mode of dongle n 1or0 AT amp V lt cr gt lt cr gt lt lf gt S0 m0 S1 m1 Sn mn lt cr gt lt lf gt lt cr gt lt lf gt OK lt cr gt lt lf gt View all the values of internal S registers AT BTSD lt cr gt lt cr gt lt lf gt bdaddr of secured device 1 lt cr gt lt lf gt lt cr gt lt lf gt bdaddr of secured device 1 lt cr gt lt lf gt lt cr gt lt lf gt OK lt cr gt lt lf gt Query the bd addresses of secured devices AT BTCSD lt cr gt lt cr gt lt lf gt OK lt cr gt lt lf gt Clear the list of secured devices AT BTFP n lt cr gt lt cr gt lt lf gt OK lt cr gt lt lf gt Force paring when connecting as master AT UARTCON
33. off The SD pair will connect automatically when they are powered up again 7 release this paring set them to MODE 0 by entering AT BTMODE 0 or reset the units by pressing the RESET button aleas B n OK Promi SD User Manual ver 1 7 25 www initium co kr 2 2 6 AT command vs Operational Status The AT command sets listed above can be executed per Promi SD operational status The following table shows the operational status and executable AT command sets AT Command Standby Pending Online AT lt cr gt y y ATZ lt cr gt V V AT BTINQ lt cr gt y ATD112233445566 lt cr gt Vy ATD lt cr gt y AT BTSCAN n lt cr gt y AT BTSCAN 112233445566 lt cr gt y AT BTCANCEL lt cr gt V ATO lt cr gt y ATH lt cr gt 2 AT BTAUTH Auth Encr lt cr gt y AT BTMODE n lt cr gt VI AT BTNAME Name lt cr gt a AT BTKEY nnnn lt cr gt y ATS10 0 or ATS10 1 AT BTINFO lt cr gt V V AT UARTCONFIG b p s lt cr gt 1 Effective when Promi SD is not in connection with Bluetooth 2 Effective when Promi SD is in connection status with Bluetooth 3 Recommend to be used when Promi SD is not in connections status with Bluetooth 4 To apply new values to Promi SD software reset requires by ATZ command or restart Promi SD NOTE Full AT commands set can be found in Appendix B Promi SD User Manual ver 1 7 26 www initium co kr 3 Technical Specifica
34. orrectly and react inappropriately To avoid these possible errors users may disable the response signals via PromiWIN or AT commands at Terminal 1 By Promi WIN check OFF at Signal pane at Device Setting panel to disable 4 response signals from Promi SD PromiWin PromiWIN 1 Default To see default configuration of Promi SD Information Operation Mode MODEO Standby status for Bluetooth connection C MODE1 This Promi SD shall connect to the last connected device only C MODE2 This Promi SD shall be connected from the last connected device only C MODES Allow any Bluetooth devices discoverfconnect to this Promi SD You must be in Pending status in MODES to be discoverable connectable evice setting To be in Pending status please click MODES and press Apply button Connection out Uart Baud Rate 9600 y Parity No Parity StopBit 1 B a Security Option Connectiontin Authentication Encryption Password 77 C OFF PSDy3a 120296 2 By AT commands at your Terminal program ATS10 1 Enabling ON 4 signals ATS10 0 Disabling OFF 4 signals ATS10 To see current status Promi SD User Manual ver 1 7 31 www initium co kr 4 3 For DCE connection Promi SD is twisted Rx Tx ready for direct DTE connection For connection to DCE equipment such as modem etc customers need to use a gender changer which twisted Tx Rx CTS RTS DTR DSR for right operation For more
35. rial port for configuring Promi SD Serial Port COM BaudRate 9600 Parity None StopBit 1 v Cancel lt Fig 1 1 gt 1 3 Select the number of the Serial port where SD01 is attached as in the Fig 1 1 above 1 4 Users need to select exactly same Baud Parity StopBit as real settings of attached SD01 9600 No OneStopBit are default initial settings of all of Promi SDs 1 5 Press OK button when finished Promi SD User Manual ver 1 7 15 www initium co kr 1 6 Open Promi WIN gt Start Configuration on the upper left menu Promi WIN will bring the information on the attached SD01 as in Fig 1 2 PromiWin Device Name PSDv3a 120296 Device Hardware Address 000853120296 2 Current Mode MODEO Current Status STANDBY Device Setting Security Authentication A No Encryption 5 No Connection out Uart Setting al Baud Rate 9600 Connection in StopBit s One Stop Bit Parity None Refresh lt Fig 1 2 gt 1 7 Click the Device Setting icon in the list control box Users may change the Baud rate Parity StopBit to meet their individual needs PromivIN PromiWIN i To see default configuration of Promi SD Operation Mode MODEO Standby status for Bluetooth connection MODE1 This Promi SD shall connect to the last connected device only MODE2 This Promi SD shall be connected from the last connected device only MODES Allow any Blue
36. scoverable and Connectable In this case refer to section 3 3 before following the instructions below 1 First check the status of the SD by entering AT BTINFO The SD response is comprised of BD_ADDR Device Name Operating Mode Operating Status Authentication and Encryption flags To make connection to other Bluetooth devices the operating status of the first SD should be Promi SD User Manual ver 1 7 21 www initium co kr STANDBY A PENDING operating status of the first SD indicates the unit is busy with another operation In this case cancel the ongoing operation by entering the AT BTCANCEL command AT BTINFO 0010 51576101010107 SN ads D o 010007 202 VO BD O Roa ID AOR OK 2 Search other local Bluetooth devices by entering the AT BTINQ command AT BTINQ 000B53000080 PSDv2g 000080 001F00 000483005205 02002 1 0 OK 3 Check the search list Enter ATD command in the BD_ADDR of any Bluetooth device for connection During the connection process the STATUS LED will flash green every second 4 Connection is indicated by the SD returning a CONNECT message and displaying a green STATUS LED ATD000B53000080 OK CONNECT 2 2 3 Making Promi SD do INQUIRY SCAN and PAGE SCAN Unlike many Bluetooth serial dongles the SD has an internal rechargeable Promi SD User Manual ver 1 7 22 www initium co kr battery As stated be
37. t If gt CONNECT lt cr gt lt lf gt or lt cr gt lt lf gt OK lt cr gt lt lf gt lt cr gt lt If gt ERROR lt cr gt lt lf gt Description Once you enter this AT command your SD does PAGE SCAN However it waits a connection from a Bluetooth device with the given BD_ADDR This process lasts during to time interval Especially when to has value of 0 your SD waits connection infinitely AT BTCANCEL lt cr gt Function Cancel currently ongoing operation of your SD Response lt cr gt lt lf gt OK lt cr gt lt lf gt Description This AT command works only when your SD is busy in doing AT BTSCAN ATD or AT BTINQ Once canceled successfully your SD will become Promi SD User Manual ver 1 7 46 www initium co kr STANBY STATUS Function Make transition from ONLINE STATUS to STANDBY STATUS Response lt cr gt lt lf gt OK lt cr gt lt lf gt Description If you input string to your SD in ONLINE STATUS your SD goes into STANBY STATUS Once SD enters into STANDBY STATUS you can use any AT command sets supported by Promi SD ATO lt cr gt Function Make transition from STANBY STATUS to ONLINE STATUS Response None Description This AT command is the counter operation of You can change the operating status to ONLINE STATUS again by using this command In ONLINE STATUS the data can be transferred between two hosts The existence of your SD beco
38. t setting Users may use DTR DSR lines for communications e ATS14 0 lt cr gt Users may use DTR DSR lines for Loop back only e ATS14 To see current status of ATS14 Default setting of CD line in Promi SD is to show the status of Bluetooth connection If users want to use CD line to send CDC signal to the other side such as for connection between Promi SD and DCE device users need to configure ATS13 ATS13 0 lt cr gt Default setting Users may use CDC line for checking Bluetooth connection ATS13 1 lt cr gt Users may receive CDC signal from other Promi SD This function will be available from future version of Promi SD for DCE devices ATS13 To see current status of ATS13 Promi SD User Manual ver 1 7 12 www initium co kr 1 6 2 Bluetooth Interface Bluetooth Specification V 1 1 Level 4 dBm Promi SD101 18 dBm Promi SD202 Range 30m Promi SD101 100m Promi SD202 Bluetooth protocols RFCOMM L2CAP SDP Supported Profiles General Access Profile Serial Port Profile Promi SD User Manual ver 1 7 www initium co kr 13 2 Configuration 2 1 Using Promi WIN With Promi SD Bluetooth wireless connections can be made to any Bluetooth device supporting SPP Serial Port Profile Especially when using the Promi SD as a cable replacement take advantage of the Promi SD automatic connection feature Once a pair of Promi SDs is set for this feature
39. they automatically connect whenever powered up A pair of Promi SD units within their radio range may be used as a virtual RS 232 cable To make wireless connections between two Bluetooth devices one device should be in Discoverable INQUIRY SCAN and Connectable PAGE SCAN as well Most Bluetooth devices are set to Discoverable and Connectable in manufacture However to maximize internal battery life Promi SD INQUIRY SCAN and PAGE SCAN are disabled To make Promi SD respond to the INQUIRY and PAGE operations of other Bluetooth devices activate INQUIRY SCAN and PAGE SCAN Before making the first Bluetooth connection with SD units be prepared with a pair of SD units and also install the PromiWIN program on the CD enclosed in the Promi SD product package Promi SD User Manual ver 1 7 14 www initium co kr Configuration By Promi WIN Please prepare two of the Promi SDs to make connection Let s say 1st unit as SD01 and 2nd unit as SD02 in this guide book Make sure that power to both SD01 and SD02 are ALWAYS supplied even when you detach from your computer 21 1 Let s make SD01 to be discoverable connectable In this procedure SD01 will become discoverable connectable to be able to receive connection from SD02 1 1 Attach SD01 to your PC and start Promi WIN 1 2 Start PromiWIN then you will see a pop up window for configuration of PromiWIN Application Setting Please setup se
40. tional Antennas Users may extend wireless link distance up to 1 2Km via Promi SD202 with Patch Antennas for both sides Model no Antennas for two Promi SD units Max Distance Promi SD101 Default Antenna Default Antenna 30 meters Default Antenna Dipole Antenna 50 meters Dipole Antenna Dipole Antenna 80 meters Patch Antenna Dipole Antenna 150 meters Patch Antenna Patch Antenna 300 meters Promi SD202 Default Antenna Default Antenna 120 meters Default Antenna Dipole Antenna 150 meters Dipole Antenna Dipole Antenna 200 meters Patch Antenna Dipole Antenna 400 meters Patch Antenna Patch Antenna 1 200 meters For information on optional Antennas refer to Chapter 5 Optional Antennas Promi SD User Manual ver 1 7 29 www initium co kr 4 Troubleshooting 4 1 ON OFF of Hardware Flow control Promi SD101 of version v2g amp v2h are designed to use CTS RTS for handshaking For equipment which is not using Hardware flow control for serial communications Promi SD101 s firmware should be set to turn OFF hardware flow control CTS RTS Customers may indicate preferences when ordering or turn off the handshaking by bridging CTS and RTS no 7 and no 8 lines using a Gender changer Version v3a has automatic detection feature of hardware flow control but in certain environment such as with PC this function may not operate well Starting from Promi SD version v3b cus
41. tions 3 1 Default Serial Settings e 9600 Baud 8 data bits no parity 1 stop bit hardware flow control 3 2 Power Consumption Condition Current Consumption Battery Life 180mA Li Poly Battery Promi SD101 Promi SD202 Promi SD101 If NOT connected to Host 3 5 mA 19 mA 49 hrs 30 min If connected to Host 13 5 mA 24 mA 13 hrs 10 min For data communications 26 5 mA 27 mA 6 hrs 50 min with Host only During INQUIRY mode 62 mA 96 mA 3 hrs 20 min For Master connection 63 mA 96 mA 3 hrs 10 min During SCAN page amp 27 mA 25 mA 6 hrs 30 min inquiry mode Park mode 13 8 mA 34 mA 12 hrs 40 min Non Park mode 17 8 mA 40 mA 10 hrs Promi SD User Manual ver 1 7 27 www initium co kr 3 3 Environmental Model No Promi SD101 Recommended operating conditions 10 C 70 C Humidity 90 Non condensing Model No Promi SD202 Recommended operating conditions 20 C 70 C Humidity 90 Non condensing 3 4 Serial Interface Model No Promi SD101 RS232 Female DSUB 9 1200 115200 baud CTS RTS flow control or no flow control Model No Promi SD202 RS232 Female DSUB 9 1200 230400 baud Automatic Detection Feature of Hardware flow control DTR DSR for loop back amp communications CDC to check Bluetooth connection Promi SD User Manual ver 1 7 28 www initium co kr 3 5 Maximum distance between Promi SD s In open space maximum distances between two Promi SD units were tested using different types of Op
42. tomers may choose the usage of hardware flow control using PromiWIN software PromiWiIN Config COM Port 1 BaudRate 9600 Parity Bit No Parity StopBit 1 Promi WIN i Default To see default configuration of Promi SD Information Operation Mode MODED Standby status for Bluetooth connection MODET This Promi SD shall connect to the last connected device only C MODE2 This Promi SD shall be connected from the last connected device only C MODES Allow any Bluetooth devices discover connect to this Promi SD You must be in Pending status in MODES to be discoverable connectable To be in Pending status please click MODES and press Apply button Connection out Uart Baud Rate 9600 Device Name PSDv3b 160085 Parity No Parity Security Option Signal Connection in Authentication Encryption ON HAW Flow control peers OFF If checked Promi SD will use hardware flow control If you do not want to use the function please uncheck and press Apply button Promi SD User Manual ver 1 7 30 www initium co kr 4 2 Enabling Disabling of Response Signals OK CONNECT DISCONNECT amp ERROR Promi SD will respond to users on the current status success amp failure of connections and error mode Both PromiWIN and Terminal Programs will receive related response signals from Promi SD In some cases various equipment may regard these four response signals inc
43. tooth devices discover connect to this Promi SD You must be in Pending Lit MODE to be discoverable connectable Information B fg Connectiontin I Authentication Encryption cee Password lt Fig 1 3 gt 1 8 Click the Connection in icon in list control box Check both options and then click the START button as shown in Fig 1 5 Promi SD User Manual ver 1 7 16 www initium co kr PromivIN PromiWIN 1 Option Information Other Bluetooth Devices can discover this Promi SD Enable inquiry scan 2 Allow other Bluetooth Devices to Connect Enable page scan Device Setting Seconds for waiting connection If you set the time for waiting connection to 0 it will wait infinitely 4 second Connection out Please let the other Bluetooth device 21 discover connect to this Promi SD during Waiting time Connectionin omea lt Fig 1 5 gt 1 9 SD01 now became Discoverable Connectable so it can receive Bluetooth connection from SD02 The STATUS LED of SD01 will blink green twice every 3 seconds 1 10 Detach SD01 from your computer making sure its status LED is blinking green 1 11 Close Promi WIN 21 2 Let s make SD02 to search SD01 and connect to 2 1 Attach SD02 to your PC and start Promi WIN 2 2 Select the number of the Serial port where SDO2 2 3 Users need to select exactly same
Download Pdf Manuals
Related Search