Home

DNA11xx Series - Dante Security

image

Contents

1. System upgrades red light flashes System resets red light flashes Green light Y Normal working status green light is on Display record status Record green light flashes Yellow light E Detect the wireless device yellow light is on Connect to 3G card Please note it is for 3G series product only Connect to 3G WIFI Antenna port antenna to receive the wireless signal Please note this function is for some series products only Alarm input port I O port Alarm input port 1 To receive the signal from the external alarm device Z O Alarm output port Alarm output port To output alarm signal to the alarm device e NO Normal open alarm output end C Alarm output public end Alarm input ground end RS485 port RS485 A port control external PIZ RS485_B port control external PIZ RS232 port RS232 RX RS232 receive end RS232_ TX RS232 COM send out end IR light port External IR light signal control port RESET RESET button Restore factory default setup When system is running normally press the RESET button for at least 5 seconds system can restore factory default setup AUDIO OUT Audio output port Audio output 3 5mm Output audio signal to JJ A 4 x Z gt JACK port the passive device such as earphone AUDIO IN Audio input port Audio input 3 5mm Input audio signal JACK port from devices such as pick up LANET Net
2. 05 23 16 24 48 52 54 40 fa 35 37 00 12 26 45 23 65 00 1a B6b 90 57 db 00 09 30 ad 00 12 Select one IP address and then right click mouse you can see an interface is shown as in Figure 3 2 ConfigTool Device List SH IF Address 1 10 7 6 47 2 10 7 6 21 5 10 T 10 104 4 LO 7 2 2 5 10 7 1 115 a 10 T 10 91 T 192 168 0 108 o 10 7 2 61 Tip You can click login button directly and then input corresponding information to login Fort STITT STITT JTTTT JTTTT Subnet Mask 255 ada DO 255 255 O 0 Do Do Do 0 0 O 0 O 0 Default Gat Refresh Rj Logout E Figure 3 2 Mac Address 52 54 40 90 52 54 40 d 55 52 54 40 d 55 00 05 23 16 24 falas E A Open Device Web 90 57 J ad 00 15 Select the Open Device Web item you can go to the corresponding web login interface See Figure 3 3 Figure 3 3 If you want to modify the device IP address without logging in the device web interface you can go to the configuration tool main interface to set In the configuration tool search interface Figure 3 1 please select a device IP address and then double click it to open the login interface Or you can select an IP address and then click the Login button to go to the login interface See Figure 3 4 In Figure 3 4 you can view device IP address user name password and port Please modify the corresponding
3. AJ File Edit View Favorites Tools Help x aA A 2 Search Sie Favorites LA A 2 las Address http 10 15 5 243 v Eu E O GO A A TA ATA ive Logout sub steam co HE eie aos NO signal a ion SS javascript Y Local intranet Figure 4 4 Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction 20 Appendix Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Eee CC i et es es Te Device Construction Material O Wire and Cable O AA 1 e Te Le RR Je Accessories O O O O O O O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T 11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes Note e Th
4. DADO O IN A nl Ge A 8 SN E A ete ei 8 2 ce CMV O atibaia sein a ade cas tagcat ren eect asset Sow Sid E a id add eee 9 2 3 IGG E cad dai dada di eo sad RAD T aa ci Ea a 9 Zed MVS Cea ANO aaa O 9 2 Se ROMOVO quitada ld alii 10 2 4 3G WIFI Antenna us a di ds 11 2 AM MVS CATON dc eels 11 242 TRCIMOV Bustillos ci ost dida ness dass casi 12 25 KOPO asa persa tesa arcs O ap OR AR A A RR O ER RR DA haters 12 2 5 1 Install and Remove Cable eae 12 25 2 Alarm INDUL ane QUU sau ess o aaa ds 13 QUICK Contiduration TOO eran aial aladas 15 3 1 OVON IO eee ae A a a EET ORNS AMET Gde RSET 15 3 2 DC AON PAM o IR DRE RR A DRE RR ERROR RE NEED O RR atone 15 NAVE IC DCP AAA led orando ico ni aaa e dal a 18 4 1 Network OnnecUON iii ia ecu Dios 18 4 2 LOG I AAG Logo Ein 18 111 Appendix Toxic or Hazardous Materials or Elements 1V 1 Framework 1 1 Rear Panel This series DNA11xx IP camera real panel is shown as below See Figure 1 1 ERIOONOGIS oy EE O O O C A aerea OY Ac 24V DE 12W e AUDIO OUT AUDIO IN The rear panel with the 100M fiber port Figure 1 1 Please refer to the following sheet for detail information Interface Name Connector Function VIDEO OUT Video output port Output analog video signal Can connect to TV monitor to view video Power port Input 12V DC or AC 24V DC 12V Power port AC 24V STATUS Red light System boot up Indication Light red light is on
5. DNA11xx Series MP IP Box Camera Installation and Operations Manual Model Number DNA1135 1 3MP DNA1145 2MP DNA1165 3MP DNA1185 5MP Description MP IP Box Style Cameras Welcome Thank you for purchasing our IP camera This quick start guide is designed to be a reference tool for your system Please keep this start guide well for future reference 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC or 24V AC in the IEC60950 1 Before you replace the SD card please unplug the power cable and then remove the shell We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modifications or attempted repair 2 Installation Do not apply power to the IP camera before completing installation Do not put object on the IP camera 3 Environment This series IP camera should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc The working temperature ranges from 10 C to 60 C Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the IP CAM Thun
6. Figure 2 18 13 Please refer to the following figure for external IR light information See Figure 2 19 IR synchronization input signal When the external IR light is on the signal cable from the board outputs the 3 3V 1mA It outputs the OV when the IR light is off GND 4 Connection Power Supplying to the IR Light Figure 2 19 14 3 Quick Configuration Tool 3 1 Overview Quick configuration tool can search current IP address modify IP address At the same time you can use it to upgrade the device Please note the tool only applies to the IP addresses in the same segment 3 2 Operation Double click the Config T ools exe icon you can see an interface is shown as in Figure 3 1 In the device list interface you can view device IP address port number subnet mask default gateway MAC address and etc ConfigTool Device List SH IF Address 1 10 7 6 4T 2 10 7 6 el F 10 T 10 104 10 T 2 2 10 T 1 113 10 T 10 91 192 165 0 108 10 T 2 61 Tip You can click login button directly and then input corresponding information to login Fort aTTTT aTTTT ITTTT ITTTT aTTTT aTTTT Subnet Mask 255 250 0 0 255 250 0 0 255 255 0 0 255 255 0 0 255 255 0 0 255 250 0 0 255 250 0 0 255 250 0 0 Default Gat 1 Bt 1 1 1 192 168 0 1 10 7 0 1 Refresh Rj Logout E Figure 3 1 Mac Address 52 54 40 90 5d 52 54 40 fd S56 44 00
7. der proof device is recommended to be adopted to better prevent thunder The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera 4 Daily Maintenance Current series IP CAM has no power button Please unplug all corresponding power cables before your installation Do not touch the CCD or CMOS part you can use the blower to clean the dust on the surface of the lens You can use the dry cloth with some alcohol to clear if necessary Please keep the dustproof cap back to protect the CCD or CMOS part if the IP camera does not work for along time If there is too much dust on the housing please use the water to dilute the mild detergent first and then use it to clean the device with the clear dry cloth Finally use the dry cloth to clean the device 5 Accessories Please open the accessory bag to check the items one by one in accordance with the list below Contact your local retailer ASAP if something is missing or damaged in the bag E O Jen C CS adapter Quick Start Guide 1 2 3 4 Table of Contents PS LA ALS ON sata A A A Se eT ee eer 1 1 1 Rear Fe A lio io ah a E EAR ae 1 1 2 Sae PN A A a e O E do pe qr RR DO 5 1 3 POMC Fe Ne asso ac A EEE 5 Motala OM DE PRP RE RR DE RD RE NR DOR NR A RE abusa 7 2 1 Lens Ansalla ton ta a de e ae a a RA A 7 2l AUTO Aperture LOS anita 7 PE Mand NAS ONG aeea a E A E EA A 7 2 1 3 Remove LOS dci 8 2 2 DE CARO a ceder ERA
8. e lens counter clockwise and then remove it from the camera Unplug the auto lens cable socket from the auto lens connector If you are using the manual aperture lens please skip to the following step e lf there is no lens please put the CCD protection cap back to protect the CCD Figure 2 3 2 2 SD Card 2 2 1 Installation Please follow the steps listed below to install SD card The interface is shown as in Figure 2 4 and Figure 2 5 e Use the screwdriver to loosen the SD card protection screw in the rear panel and then remove the SD card protection cap from the camera e Install the SD card to the camera according to the proper installation position Put the SD card protection cap back Use the screwdriver to fix the SD card protection cap screw firmly to secure the SD card protection cap in the camera Figure 2 5 2 2 2 Remove Please follow the steps listed below to remove SD card The interface is shown as Figure 2 6 Use the screwdriver to loosen the screw of SD card protection cap in the rear panel Remove the cap from the camera Follow the SD card direction to remove the SD card Insert the SD card protection cap e Use the screwdriver to fix the screw to secure the protection cap Figure 2 6 2 3 3G Card 2 3 1 Installation The 3G card installation is the same with the SD card Please follow the steps listed below to install 3G card The interfaces are shown as Figure 2 7 and Figure 2 8 Us
9. e the screwdriver to loosen the 3G card protection cap screw in the side panel and then remove the 3G card protection cap from the camera Install the 3G card to the camera according to the proper installation position Put the 3G card protection cap back Use the screwdriver to fix the 3G card protection cap screw firmly to secure the 3G card protection cap Figure 2 8 2 3 2 Remove Please follow the steps listed below to remove 3G card The interface is shown as Figure 2 9 Use the screwdriver to loosen the screw of 3G card protection cap in the rear panel Remove the cap from the camera Follow the 3G card direction to remove the 3G card Insert the 3G card protection cap Use the screwdriver to fix the screw to secure the protection cap Figure 2 9 10 2 4 3G WIFI Antenna 2 4 1 Installation Line up the thread of the screw of the 3G WIFI antenna to the thread of the rear panel See Figure 2 10 Please turn according to the direction in the following figure until antenna is secure firmly See Figure 2 11 Figure 2 11 After you fix the 3G WIFI antenna to the WIFI port of the rear panel you can adjust the antenna direction See Figure 2 12 Figure 2 12 11 2 4 2 Remove Use your hands to hold the 3G WIFI thread end and then turn according to the following figure See Figure 2 13 Now you can see the antenna is away from the thread See Figure 2 14 Figure 2 14 Remove the 3G WIFI a
10. information to login Please note the port information here shall be identical with the port value you set in TCP port in Web Network interface Otherwise you cannot login the device If you are use device background upgrade port 3800 to login other setups are all invalid IF Address 10 10 35 16 User Name admin OOK Fassword Port atri Figure 3 4 After you logged in the configuration tool main interface is shown as below See Figure 3 5 16 ConfigTool HetWork Parameter General Parameter DHCP Enable PPPOE TF Address 10 10 3 16 System Information Subnet Mask 255 255 0 0 System Upgrade Gateway 10 10 0 1 Mac Address 52 54 40 fa 43 Bd Figure 3 5 For detailed information and operation instruction of the quick configuration tool please refer to the Quick Configuration Tool User s Manual included in the resources CD 4 Web Operation This series IP CAM product support the Web access and management via PC Web includes several modules monitor channel preview PTZ control system configuration alarm and etc 4 1 Network Connection Please follow the steps listed below for network connection e Make sure the IP CAM has connected to the network properly e Please set the IP address subnet mask and gateway of the PC and the IP CAM respectively IP CAM default IP address is 192 168 1 108 Subnet mask is 255 255 255 0 Gateway is 192 168 1 1 U
11. is quick start guide is for reference only Slight difference may be found in user interface All the designs and software here are subject to change without prior written notice If there is any uncertainty or controversy please refer to the final explanation of us Please visit our website or contact your local service engineer for more information 21
12. nstall C type lens Remove the CCD protection cap from the device Install the C CS adapter to the camera Turn clockwise to secure against the focusing ring firmly Line up the C lens to the installation position of the C CS adapter Turn clockwise to fix the lens Use slotted screwdriver to fasten the screw near the focusing ring and then turn counter clockwise to move the focusing ring out for several millimeters Now you can focus manually and check the video is clear or not If you can not see the clear video you can adjust via the flange back After you completed the focus setup use the slotted screwdriver to fix the screw firmly Fasten the focusing ring Now the installation completed Install CS type lens Remove the CCD protection cap from the device Line up the CS lens to the lens installation position of camera focusing ring Turn clockwise to fix the lens Use slotted screwdriver to fasten the screw near the focusing ring and then turn counter clockwise to move the focusing ring out for several millimeters Now you can focus manually and check the video is clear or not If you can not see the clear video you can adjust via the flange back After you completed the focus setup use the slotted screwdriver to fix the screw firmly Fasten the focusing ring Now the installation completed Figure 2 2 2 1 3 Remove Lens Please follow the steps listed below to remove lens The interface is shown as in Figure 2 3 e Turn th
13. ntenna from the port of the rear panel See Figure 2 15 Figure 2 15 2 5 I O Port 2 5 1 Install and Remove Cable Install Cable 12 Please follow the steps listed below to install the cable See Figure 2 16 Use the small slotted screwdriver to press the corresponding button of cable groove Insert the cable into the groove and then release the screwdriver Remove Cable Please follow the steps listed below to remove the cable Use the small slotted screwdriver to press the corresponding button of cable groove Remove the cable out of the groove and then release the screwdriver Slotted Screwdriver Figure 2 16 2 5 2 Alarm Input and Output Please refer to the following figure for alarm input information See Figure 2 17 Alarm input When the input signal is idle or grounded the device can collect the different statuses of the alarm input port When the input signal is connected to the 5V or is idle the device collects the logic 1 When the input signal is grounded the device collects the logic 0 Alarm Input _ Collecting Figure 2 17 Please refer to the following figure for alarm output information See Figure 2 18 Port NO and Port C composes an on off button to provide the alarm output If the type is NO this button is normal open The button becomes on when there is an alarm output If the type is NC this button is normal off The button becomes off when there is an alarm output
14. se order ping IP camera address to check connection is OK or not 4 2 Login and Logout Open IE and input IP camera address in the address bar For example if your camera IP is 192 168 1 108 then please input http 192 168 1 108 in IE address bar See Figure 4 1 Input your IP DD dire Grs gt address here Blank Page Windows Internet Explorer y E v El about blank amp x w dr Blank Page Internet R 100 Figure 4 1 The login interface is shown as below See Figure 4 2 Please input your user name and password Default factory name is admin and password is admin Note For security reasons please modify your password after you first login 18 A http 110 15 5 243 Windows Internet Explorer File Edit View Favorites Tools Help y 2 x E pe Search Sie Favorites A 2 LA address http 10 15 5 243 DRE e WEB SERVICEszo Username jadmin Password ss Local intranet Figure 4 2 If it is your first time to login in system pops up warning information to ask you whether install control webrec cab or not after you logged in for one minute Please click OK button system can automatically install the control When system is upgrading it can overwrite the previous Web too If you can t download the ActiveX file please check whether you have installed the plug in to disable the control download Or you can lower
15. the IE security level See Figure 4 3 Internet Options dle Security Settings Internet Zone General Security Privacy Content Connections Programs Advanced Settings Disable Enable Download signed Actives controls not secure Disable Enable not secure Prompt recommended 9 Download unsigned Actives controls not secure Disable recommended Enable not secure O Prompt 9 Initialize and script Actives controls not marked as safe for s Disable recommended Enable not secure Prompt 4 Run Activex controls and plug ins Li mo Adrainiche akar somes A sa jil Takes effect after vou restart Internet Explorer Select a zone to view or change security settings tod e Y i Internet Local intranet Trusted sites gt Internet This zone is for Internet websites except those listed in trusted and restricted zones Security level For this zone Allowed levels For this zone Medium to High Medium high Appropriate For most websites Prompts before downloading potentially unsafe content Unsigned Actives controls will not be downloaded Reset custom settings Reset to medium high default v Custom level Default level Reset all zones to default level o Figure 4 3 After you logged in you can see the main window See Figure 4 4 19 A http 10 15 5 2439 Windows Internet Explorer N
16. work port Ethernet port Connect to standard Ethernet cable Support PoE function OPT 100M fiber port 155M single fiber Transmit 100M dual direction SFP fiber module SD SD card port Ethernet data Connect to SD card Note e When you install the SD card please make sure current card is not in write mode and then you can install it to the camera When you remove the SD card please make sure current card is not in write mode Otherwise it may result in data loss or card damage Before hot swap please stop record operation Please make sure the device is securely earthed to prevent the thunderstorm strike 1 2 Side Panel Please refer to the following interface for side panel dimension information The unit is mm See Figure 1 2 A O pm 4 a Ps us o Qd Figure 1 2 1 3 Front Panel Please refer to the following interface for the front panel information The unit is mm See Figure 1 3 Figure 1 3 2 Installation 2 1 Lens Installation 2 1 1 Auto Aperture Lens Please follow the steps listed below for auto aperture lens installation The interface is shown as in Figure 2 1 and Figure 2 2 Remove the CCD protection cap of the device and then line up the lens to the proper installation position Turn clockwise until the lens is fixed firmly Insert the lens cable socket to the auto lens connector in the side panel 2 1 2 Manual Lens I

Download Pdf Manuals

image

Related Search

Related Contents

Dell PowerVault NX300 User's Manual  CARREGADOR DE VIAGEM 4 PORTAS USB  Connecting a Magelis XBTG/XBTGT Operator Terminal to an Allen  ASUS P8Z77-V User's Manual  S246 Service Manual - Mobility Scooters Direct  Sopar New Spring  G4218-90001 - Agilent Technologies  Nº MODELO WV-SFV631L/WV-SFV611L WV - Psn  Tripp Lite DisplayPort to HDMI Converter, 1920x1200/1080p (M/F) 6-in.  Nr.: 01019  

Copyright © All rights reserved.
Failed to retrieve file