Neutron Engineering Inc. - Fu Da Tong Technology Co., Ltd.
Contents
1. 4 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network All other support equipments powered from additional LISN s The LISN provide 50 Ohm 50uH of coupling impedance for the measuring instrument Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long VO cables that are not connected to a peripheral shall be bundled in the center The end of the cable may be terminated if required using the correct terminating impedance The overall length shall not exceed 1 m d LISN at least 80 cm from nearest part of EUT chassis e For the actual test configuration please refer to the related Item EUT Test Photos 4 1 4 DEVIATION FROM TEST STANDARD No deviation 4 1 5 TEST SETUP Vertical Reference Ground Plane Test Receiver Report No NEI I 1 H0712004 Page 12 of 22 4 1 6 EUT OPERATING CONDITIONS The EUT exercise program EMC exe used during radiated and or conducted emission measurement was designed to exercise the various system components in a manner similar to a typical use Report No NEI I 1 H0712004 Page 13 of 22 4 1 7 TEST RESULTS Wii CONTACTLESS 3 SULI S CHARGER Model Name Wii07 Temperature 25 C Relative Humidity 60 Pressure 1008 hPa Test Voltage AC 100V 50 or 60Hz Test Mode charge Freq Terminal2. CF Measured FS Limits QP MHz H V dBuV dB dBuV m dBuV m dB 3400 H 285 795 2060 3000 940 5140 H 285 647 2210 3000 790 7540 H 2825 957 1868 3000 1132 193340 H 2717 584 2133 3000 867 172600 H 2665 542 2123 3000 877 18800 H 2757 726 2031 3000 969 Remark 1 Reading in which marked as QP or Peak means measurements by using are Quasi Peak Mode or Peak Mode with Detector BW 120KHz SPA setting in RBW 120KHz VBW 120KHz Swp Time 0 3 sec MHz 2 All readings are Peak unless otherwise stated QP in column of Note Peak denotes that the Peak reading compliance with the QP Limits and then QP Mode measure ment didn t perform 8 Measuring frequency range from 30MHz to 1000MHz 4 If the peak scan value lower limit more than 20dB then this signal data does not how in table dBuV m Limit Margin 515 000 1000 000 MHz Heport No NEI 1 H0712004 Page 20 of 22 5 EUT TEST PHOTO Conducted Measurement Photos Radiated Measurement Photos
3. DC O P 6 0V 1 0A 6 0W Connecting Port s Please refer to the User s Manual Products Covered AC DC Adapter Model No PA1008 1DU EUT Modification s N A Note 1 For a more detailed features description please refer to the manufacturer s specifications or the User s Manual Report No NEI VCCI 1 H0712004 7 of 22 3 2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT the test system was pre scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level Each of these EUT operation mode s or test configuration mode s mentioned above was evaluated respectively Pretest Test Mode Description Mode 1 charge For Conducted Test Final Test Mode Description Mode 1 charge For Radiated Test Final Test Mode Description Mode 1 charge Report No NEI VCCI 1 H0712004 Page 8 of 22 3 3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED E 2x2 Remote Control C 1 Power Cable Heport No NEI I 1 H0712004 Page 9 of 22 3 4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units The following support units or accessories were used to form a representative test configuration during the tests Equipment Mfr Brand Mod
4. EUT OPERATING CONDITIONS 4 2 7 TEST RESULTS EUT TEST PHOTO CANN oo c0 A rcr RONDNDN rrr o ooco 1 1 0o N Report No NEI VCCI 1 H0712004 Page 3 of 22 1 CERTIFICATION Equipment Wii CONTACTLESS CHARGER Brand PowerHouse Model Wii07 Applicant Fu Da Tong Technology Co Ltd Date of Test Dec 24 2007 Jan 25 2008 Standards VCCI Technical Requirement V 3 2007 04 CISPR 22 2005 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc EMC Laboratory The test data data evaluation and equipment configuration contained in our test report Ref No NEI VCCI 1 R0712004 were obtained utilizing the test procedures test instruments test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO 17025 quality assessment standard and technical standard s Report No NEI 1 H0712004 Page 4 of 22 2 SUMMARY OF TEST RESULTS Test procedures according to the technical standards Emission Standard Test Item Limit Judgment VCCI Technical Requirement V 3 2007 04 CISPR 22 2005 Conducted Emission Class B PASS Radiated Emission Class B PASS NOTE 1 denotes test is not applicable in this Test Report 2 For client s request and manual description the test will not be execut
5. Measured dBuV Limits dBuV MHz LN QP Mode AV Mode GP Mode AV Mode dB Remark 1 Reading in which marked as QP means measurements by using are Quasi Peak Mode with Detector BW 9KHz SPA setting in RBW 10KHz VBW 10KHz Swp Time 0 3 sec MHz Reading in which marked as AV means measurements by using are Average Mode with instrument setting in RBW 1MHz VBW 10Hz Swp Time 20 3 sec MHz 2 All readings QP Mode value unless otherwise stated AVG in column of Note If the QP Mode Measured value compliance with the QP Limits and lower than AVG Limits the EUT shall be deemed to meet both QP amp AVG Limits and then only QP Mode was measured but AVG Mode didn t perform In this case a marked in AVG Mode column of Interference Voltage Measured 3 Measuring frequency range from 150KHz to 30MHz 80 0 dBuV Heport No NEI I 1 H0712004 Page 14 of 22 Wii CONTACTLESS CHARGER Temperature 25 Relative Humidity 160 Pressure 1008 hPa Test Voltage AC 100V 50 or 60Hz Test Mode charge Terminal Measured dBuV Limits dBuV MHz d B EU NIE Model Name Wii07 LN Remark 1 Reading in which marked as QP means measurements by using are Quasi Peak Mode with Detector BW 9KHz SPA setting in RBW 10KHz VBW 10KHz Swp Time 0 3 sec MHz Reading in which marked as AV means measurements by using are Average Mode with
6. Neutron Engineering VCCI Test Report Issued Date Jan 28 2008 Project No R0712004 Equipment Wii CONTACTLESS CHARGER Model Name WiiO7 Applicant Fu Da Tong Technology Co Ltd Address 14F 5 No 872 Zhongzheng Rd Zhonghe City Taipei County 235 Taiwan R O C Tested by Neutron Engineering Inc EMC Laboratory Date of Test Dec 24 2007 Jan 25 2008 Testing Engineer Avew Liu foy Peter Li Technical Manager Authorized Signatory NEUTRON ENGINEERIN No 132 1 Lane 329 Sec 2 Palain Rd Shijr City Taipei Taiwan TEL 02 2646 5426 FAX 02 2646 6815 R 1347 1410 2004 j Page Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory NML of R O C or National Institute of Standards and Technology NIST of U S A Neutron s reports apply only to the specific samples tested under conditions It is manufacture s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components Neutron shall have no liability for any declarations inferences or generalizations drawn by the client or others from Neutron issued reports Neutron s reports must not be used by the client to claim product endorsement by the authorities o
7. R Model Name Wii07 Temperature 13 C Relative Humidity 84 Pressure 1029 hPa Test Voltage AC 100V 50 or 60Hz Test Mode charge Reading RA Corr Factor CF Measured FS Limits QP MHz H V dBuV dB dBuV m dBuV m dB 4140 V 3205 697 2508 3000 492 4970 V 3132 642 2490 3000 510 1110 V 3160 721 2439 300 561 12030 V 2925 641 2284 3000 716 12800 V 2847 609 2238 30 00 762 17690 v 2762 572 2190 3000 810 Remark 1 Reading in which marked as QP or Peak means measurements by using are Quasi Peak Mode or Peak Mode with Detector BW 120KHz SPA setting in RBW 120KHz VBW 120KHz Swp Time 0 3 sec MHz 2 All readings are Peak unless otherwise stated QP in column of Note Peak denotes that the Peak reading compliance with the QP Limits and then QP Mode measure ment didn t perform 3 Measuring frequency range from 30MHz to 1000MHz 4 If the peak scan value lower limit more than 20dB then this signal data does not how in table dBu m Limit Margin 515 000 1000 000 MHz Report No NEI 1 H0712004 Page 19 of 22 Wii CONTACTLESS i EUT CHARGER Model Name Wii07 Temperature 13 C Relative Humidity 84 Pressure 1029 hPa Test Voltage AC 100V 50 or 60Hz Test Mode charge Reading RA Corr Factor
8. ed Page 5 of 22 2 1 TEST FACILITY The test facilities used to collect the test data in this report is C01 OS01 at the location of No 132 1 Lane 329 Sec 2 Palain Road Shijr City Taipei Taiwan 2 2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y expended uncertainty is based on a standard uncertainty multiplied by a coverage factor of kz2 gt providing a level of confidence of approximately 95 Conducted Measurement Test Site Method Measurement Frequency Range C01 ANSI 150 KHz 30MHz B Radiated Measurement Test Site Method Measurement Frequency Range 30MHz 200MHz 30MHz 200MHz Mid A 200MHz 1 000MHz 200MHz 1 000MHz 30MHz 200MHz 30MHz 200MHz 200MHz 1 000MHz 200MHz 1 000MHz Report No NEI VCCI 1 H0712004 Page 6 of 22 3 GENERAL INFORMATION 3 1 GENERAL DESCRIPTION OF EUT Equipment Wii CONTACTLESS CHARGER Brand Name PowerHouse Model Name Wii07 OEM Brand Model Name N A Model Difference N A The EUT is a Wii CONTACTLESS CHARGER Based on the application features or specification Product Description exhibited in User s Manual the EUT is considered as an ITE Computing Device More details of EUT technical specification please refer to the User s Manual Power Source DC Voltage supplied from AC DC adapter Power Rating AC I P 100 240V 50 60Hz 0 3A
9. el Type No FCC ID Wii E 1 CONTACTLESS PowerHouse Wii07 VXDWIIO7 N A EUT CHARGER E2 Remote control RVL 003 POO WC45 N A Shielded Type Ferrite Core NO NO 1 The support equipment was authorized by Declaration of Conformity 2 For detachable type I O cable should be specified the length in cm in Length column Report No NEI I 1 H0712004 Page 10 of 22 4 EMISSION TEST 4 1 CONDUCTED EMISSION MEASUREMENT 4 1 1 POWER LINE CONDUCTED EMISSION FREQUENCY RANGE 150KHZ 30MHZ Class A dBuV Class B dBuV Quasi peak Average Quasi peak Average 0 15 0 5 79 00 66 00 66 56 56 46 0 50 5 0 73 00 60 00 56 00 46 00 5 0 30 0 73 00 60 00 60 00 50 00 Note 1 The tighter limit applies at the band edges 2 The limit of marked band means the limitation decreases linearly with the logarithm of the frequency in the range FREQUENCY MHz 4 1 2 MEASUREMENT INSTRUMENTS LIST Item Kind of Equipment Manufacturer Type No Serial No Calibrated until 1 LISN EMCO 3816 2 00042990 Jan 25 2008 2 Pulse Limiter Electro Metrics EM 7600 112644 Nov 27 2008 3 Test Cable N A C01 N A Oct 10 2008 4 EMI Test Receiver R amp S ESCI 100082 Mar 08 2008 Remark N A denotes No Model Name Serial No or No Calibration specified Heport No NEI VCCI 1 H0712004 Page 11 of 22 4 1 3 TEST PROCEDURE a The EUT was placed 0
10. instrument setting in RBW 1MHz VBW 10Hz Swp Time 20 3 sec MHz 2 All readings QP Mode value unless otherwise stated AVG in column of Note If the QP Mode Measured value compliance with the QP Limits and lower than AVG Limits the EUT shall be deemed to meet both QP amp AVG Limits and then only QP Mode was measured but AVG Mode didn t perform In this case a marked in AVG Mode column of Interference Voltage Measured 3 Measuring frequency range from 150KHz to 30MHz 80 0 dBu Heport No NEI VCCI 1 H0712004 Page 15 of 22 4 2 RADIATED EMISSION MEASUREMENT 4 2 1 LIMITS OF RADIATED EMISSION MEASUREMENT Class A at 10m Class B at 10m dBuV m dBuV m 30 230 40 30 230 1000 47 37 Notes 1 The limit for radiated test was performed according to as following CISPR 22 FCC PART 15B ICES 003 2 The tighter limit applies at the band edges 3 Emission level dBuV m 20log Emission level uV m FREQUENCY MHz Report No NEI I 1 H0712004 Page 16 of 22 4 2 2 MEASUREMENT INSTRUMENTS LIST Kind of Equipment Type No Calibrated until Log Bicon Antenna Schwarzbeck VULB 9160 3176 Feb 05 2008 o Antenna Mast Chance Most GWTBXS NA Remark N A denotes No Model Name Serial No and No Calibration specified 4 2 3 TEST PROCEDURE The measuring distance of at 10 m shall be used for measurements at frequency up to 1GHz For frequencie
11. r any agency of the Government This report is the confidential property of the client As a mutual protection to the clients the public and Neutron self extracts from the test report shall not be reproduced except in full with Neutron s authorized written approval Neutron s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements and accredited by the conformity assessment authorities listed in this test report Limitation For the use of the authority s logo is limited unless the Test Standard s Scope s Item s mentioned in this test report is are included in the conformity assessment authorities acceptance respective Report No NEI 1 H0712004 Page 2 of 22 Table of Contents CERTIFICATION SUMMARY OF TEST RESULTS 2 1 TEST FACILITY 2 2 MEASUREMENT UNCERTAINTY GENERAL INFORMATION 3 1 GENERAL DESCRIPTION OF EUT 3 2 DESCRIPTION OF TEST MODES 3 3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 3 4 DESCRIPTION OF SUPPORT UNITS EMC EMISSION TEST 4 1 CONDUCTED EMISSION MEASUREMENT 4 1 1 POWER LINE CONDUCTED EMISSION 4 1 2 MEASUREMENT INSTRUMENTS LIST 4 1 3 TEST PROCEDURE 4 1 4 DEVIATION FROM TEST STANDARD 4 1 5 TEST SETUP 4 1 6 EUT OPERATING CONDITIONS 4 1 7 TEST RESULTS 4 2 RADIATED EMISSION MEASUREMENT 4 2 1 LIMITS OF RADIATED EMISSION MEASUREMENT 4 2 2 MEASUREMENT INSTRUMENTS LIST 4 2 3 TEST PROCEDURE 4 2 4 DEVIATION FROM TEST STANDARD 4 2 5 TEST SETUP 4 2 6
12. s above 1GHz any suitable measuring distance may be used The EUT was placed on the top of a rotating table 0 8 meters above the ground at a 3m or 10 meter open area test site The table was rotated 360 degrees to determine the position of the highest radiation height of the equipment or of the substitution antenna shall be 0 8 m the height of the test antenna shall vary between 1 m to 4 m Both horizontal and vertical polarizations of the antenna are set to make the measurement The initial step in collecting radiated emission data is a spectrum analyzer peak detector mode pre scanning the measurement frequency range Significant peaks are then marked and then Quasi Peak detector mode re measured If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed f For the actual test configuration please refer to the related Item EUT Test Photos 4 2 4 DEVIATION FROM TEST STANDARD No deviation Report No NEI I 1 H0712004 Page 17 of 22 4 2 5 TEST SETUP _ Ground Plane Test Receiver Amp 4 2 6 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 4 1 6 Unless otherwise a special operating condition is specified in the follows during the testing Report No NEI VCCI 1 H0712004 Page 18 of 22 4 2 7 TEST RESULTS Wii CONTACTLESS E U T CHARGE
Download Pdf Manuals
Related Search