Alpha bollard user manual
Contents
1. 04 2006 A11 2009 A1 2010 A12 2011 e ETSI EN 62031 2008 e EN 60529 A1 2000 e EN 60598 2009 e EN 60068 2 75 1998 e EN 62262 2004 3 SAFETY Observe national safety standards when installing and using this light Geoled accepts no liability for inappropriate implementation or installation of the product Any alterations to the bollard are made solely under the responsibility of the person making them The bollard should never operate if not fully assembled The base of the bollard should not be lower than the top of the ground finishing coat Storage conditions excluding outdoor installation Maximum storage period one year Temperature 20 to 25 C Humidity 45 to 75 6 4 WARRANTY Products supplied by Geoled come with a three year warranty starting on the date of delivery covering all hidden defects originating from a defect in materials design flaw or manufacturing defect affecting the supplied products in particular their electronic and electrical components rendering them unfit for purpose The warranty is limited to replacing parts recognized as defective by our technical service The warranty is void in case of misuse failure to observe directions for use negligence or lack of maintenance by the customer Nor does it cover normal wear or cases of force majeure The warranty is also void 3 if the material or faulty design originates from the customer Assembly sketches and s2. you for the password As you don t know it yet press EY again to quit the recovery process After noting the six light sequences send them to Geoled or its approved representative and get the code in return subject to the checks referred to at the beginning of this section 21 14 QUESTIONS amp ANSWERS 1 Ifa bollard fails to light up at nightfall or during the night check that a the window above the photovoltaic cell is not obstructed from sunlight which recharges its batteries b the bollard has not suffered any knocks that may have damaged its light diffusers solar collector or electronics lina c the lighting duration after sunset has not already been exceeded see Settings Timer section page 18 in which case it is normal that it does not come on The bollard will come on again if you change the Timer settings increase the duration or switch to lighting all night long for instance or when night falls again 2 i the III EE EI EPI UCSC excess of 30 Klux for a minimum battery charge e the batteries have been properly inserted as instructed in this manual see 11 BATTERIES 2 If the bollard emits red flashes when you want to adjust its settings the bollard is protected by a security code enter it to be able to adjust its settings 3 If you cannot change the settings of one or more bollards colour brightness sequences periods networking etc check that a the bollards are in Command Mode be
3. Ge lec Alpha Bollard User manual 10 11 12 13 14 Contents PRODUC T ta thea nie dl ace nal iceman s eu a RAA eae telat des ti a 5 DEGEARATION OFIG ONE OFAM remenant a a a E alte tal Settee teats AE E ia ale canini 6 SAFE rd iii edad 6 WARRANTS A A ES a alia 7 PERA 8 ALPHA BOLAR D sl linea 9 REMOTE CONTROLE sutidan dl it 10 INSTAECATIONEAND ACTIVATION smell eta 11 PRECAUTIONS ASA Et ee ahaa as CS EN a aes 14 GENERAKINSTR CHONS cists odat enti tada acta Santa intacta ales Dia sia SRA A did dida 11 FIXING ONA BLOCK een eine oa OE a NS RASA EN dais 12 ACCESSORIES fora vard A ce ta alia ia ASI I a ae Rta acid chee RA nee a entes 13 MAINTENANCE ee es En ee 13 BALTERIES NSERTINGIGHANGING ara ee en EANA TAEA ns iii italiana 14 OPERAN PRINCIPLES apa a a A A O A KSR AAA E AVE AEE 15 SE MN Satriani lbn 16 SETTING INSTRUGTIONSHKEY TO SYMBOLS ed nee 17 SUR EES ES a AIA EA dii NN 18 PIMEC o MAE A dah acetat danesa RA aa ie 18 NERVORENG OR ama 19 DECURIRECORE gati ori N ai il etat iii ii A iii 20 RECOVERING THE SECURITY CODE SS el la dha Sieh iii 21 QUESTIONS A ANSWER S alal Dieli 22 1 PRODUCT Product name Alpha Usage Marking and signage LED lights with built in solar collector Geoled bollards are designed and made for outdoor use in areas where a high degree of resistance is required This process of recovering solar power with a built in photovoltaic collector offers extended operating time The light tur
4. angle 7 Replace the battery covers Screw in the battery covers 8 Put the bollard back on its base and screw in the lateral screw 9 Let the bollard charge for at least two or three days in bright sunlight Caution there is a risk of explosion if the battery is replaced with an incorrect type of battery Dispose of used batteries as instructed 14 12 OPERATING PRINCIPLES The Alpha bollard is a self powered outdoor light Its power is supplied by a photovoltaic collector solar cell located in the upper section of the bollard The energy is stored in built in batteries The bollard turns on and off automatically according to ambient luminosity In order to accumulate enough energy in the daytime to be able to come on at night it should be placed out of any shade in such a way that it receives unobstructed sunlight directly on its top all day long Users can adjust night time lighting to limit energy consumption and provide effective markings at night for the necessary time In winter we therefore recommend setting the number of hours during which the bollard is lit based on sunset times See section 13 Settings Timer A bollard must be installed in accordance with the installation instructions Once fixed to the ground it takes two or three days for the bollard to charge up direct sunlight in clear weather Southern European conditions in order to have enough energy to proceed with the config
5. cial functions A ite OK O Confirmation Geoled CANCEL Cancellation A A A A COLOR BRIGHT DURATION PERIOD CANCEL 10 8 INSTALLATION AND ACTIVATION The bollard should be installed on a hard flat surface paving stones concrete block decking etc Fix the base to a foundation block or a buried accessory you can order separately see section 9 Accessories Precautions If you plan to network a number of bollards check that each bollard is no more than 70 metres away from another bollard on the same network it is advisable to test networking before final installation to make sure the bollards communicate with one another for bollards installed along a path make sure the bases of each bollard face in the same direction as indicated by an arrow on the base so that you can then select the lighting side uniformly for all the bollards see section 13 ADJUSTMENTS Simple adjustments Side General instructions Unscrew the screws fixing the base to the housing The bollard comes packed with two batteries Insert the batteries into the bollard see section 11 BATTERIES Install the base using your chosen fixing method fix to the ground with 3 M12 bolts or onto a block with the embedding accessory When the base is firmly secured to its bearing element and the batteries are inserted into the bollard place the bollard on its base Screw in the lateral screw retaining the housing to its base 11 n Fixing on a b
6. etwork when you press the confirm key on the remote control The network should only be controlled from one bollard at a time 16 Settings confirmation and timeout e Networked bollards Press OK O io save all changes made since the previous save and communicates them to the other bollards on the same network The bollard emits a green flash to confirm it has sent its settings to the other bollards If you do not press any settings for 30 second the bollard reverts to its previous settings e Standalone bollards simple changes in settings colour brightness side choice of sequence cycle are saved without the need to confirm by pressing Security code If the bollard has a particular security code enter it with the remote control before adjusting the settings n Setting instructions key to symbols short press on the remote control long press gt 6 seconds on a key on the remote control ED press OR ix press Cancel 1 15 enter a number between 1 and 15 1 999 enter a number between 1 and 999 1 999999 enter a number between 000001 and 999999 0 enter digit O 0000000 enter the number 000000 E the bollard emits a colour flash ein the bollard emits colour flashes 17 Simple settings Colours or COLOR White Q Brightness Q or BRIGHT Side Q selected the lighting side on the bollard Sequences a Or o to choose one of two colour brightness and lighting side settings Scroll amp scrolls cyclical
7. fore attempting to change any settings or network configuration b that a security code has been set and that you have entered it before changing any settings c if a bollard fails to follow the settings of a network check that it has been duly assigned to the said network A If one or more bollards cannot be networked check that a they all satisfy the necessary conditions for charging their batteries see point 1 above b that each bollard is no more than 70 metres away from another bollard on the same network 5 At dawn or nightfall not all the bollards on the same network come on or go off simultaneous is that normal Yes each bollard activates its LEDs solely according to the luminosity received by its solar collector which may be slightly different from bollard to the next 22 Colour cycle scrolling is not synchronized for the same network is that normal Yes this function primarily serves to show the palette of colours displayed by the Alpha bollard Real time synchronization of bollards on the same network is unnecessary for marking or guidance applications Bollards are networked solely to share identical settings to avoid the user having to move to each bollard to change its settings Can networks with different albeit similar identifiers have their own settings without any risk of interference Yes each bollard communicates only with its network identified by its network number and the security c
8. hs 5 FEATURES 1 Materials Extruded aluminium housing thermo lacquered with polyester powder Diffuser in transparent UV absorbing polycarbonate PC Other plastic parts in PP polypropylene Fixing base in injected aluminium for mounting on a foundation block or buried base accessory 2 Features Dimensions 376 mm H x 157 mm Weight 3 7 kg Protection rating IP 66 Protection rating IK 10 Appliance Class III extra low voltage power source 3 Built in light sources 4 red green blue LEDs 4 white LEDs 6200 K 4 Built in batteries LiFePO4 technology Lithium metal 2 per bollard Capacity per unit 3 000 mAh typical Dimensions 64 5 mm H x 26 mm 9 weight 90 gr IFR26650 model Caution there is a risk of explosion if the battery is replaced with an incorrect type of battery Dispose of used batteries as instructed lt i gt CE A 6 ALPHA BOLLARD Upper window built in solar cell Lateral diffuser Built in LED sources Housing 7 REMOTE CONTROL e Powered by a 3V CR2025 battery e Minimum range 5 metres Label Keys Functions COLOR oo Variation of colours BRIGHT O O Increase decrease brightness O White colour shortcut key Scrolls through the colours DURATION 00 Colour scrolling speed Selects lighting side Selects Sequence 1 or Sequence 2 Timer and Timer controlled brightness functions Q Security code SET Network configuration Spe
9. lard reverts to its initial light settings e If the security code is more than six digits long only the first three are taken into account e For networked bollards the same security code must be entered for each bollard of the same network 20 Recovering the security code If you lose the security code it can be recovered in the form of six light sequences emitted by the bollard You communicate these six light sequences to Geoled or an approved representative who will communicate the code in return This procedure presupposes than Geoled can check that the user wishing to recover the password is duly authorized to do so Recovering light sequences 1 2 3 Switch to Command Mode The bollard emits red flashes Enter the sequence 0 1 2 3 4 5 6 7 8 9 on the remote control then confirm with E The bollards flashes red and yellow alternately to indicate it has switched to Recovery Mode To recover one of the six light sequences press a number between 1 and 6 Note the number of blue red and green flashes The sequence ends with a long white flash Repeat from step 5 until you have noted down the flashes of all the light sequences 1 to 6 If a sequence of flashes has not been noted just press the corresponding key 1 to 6 to repeat it and note it down When you have noted down the flashes of all the sequence 1 to 6 enter to exit the security code recovery procedure The bollard then flashes red prompting
10. lock 1 Cast the embedding accessory in the concrete the fastening flange should be level with the concrete surface 2 Fit the base flush with the ground over the threaded rods Fix the base with a washer and bolt screwed onto each rod 3 Fix the bollard housing onto the base and fix with the lateral screws 12 9 ACCESSORIES e Part to embed with flange and support rods in zinc coated steel e Overall length 250 mm e 3 threaded M12 fastening rods on threaded flange e 3 M12 bolts and washers 10 MAINTENANCE Clean the light regularly removing dust and dirt especially on the optical parts e upper window of the photovoltaic collector e lateral diffusers Only use cleaning products that do not contain solvents Never use a high pressure washer closer than one metre away Any damaged optical parts of the bollard must be repaired immediately 13 11 BATTERIES INSERTING CHANGING 1 Remove the lateral screws 2 Remove the bollard from its base 3 Place the bollard upside down taking care not to damage the solar collector 4 Loosen the 4 screws on the battery covers and remove the covers 5 To remove the batteries place the bollard the right way up and tap it gently on the ground so that the batteries drop out 6 Check the polarities marked on the bottom of each battery compartment when inserting the new batteries Insert each contact at the same time avoid inserting them at an
11. ly through the colours Q or DURATION reduces or increases scrolling speed Scrolling is not synchronized for networked bollards Stop scrolling and return to a Or amp Timer Lighting duration From 1t0 15h long press 1 15 3 flashes purple SK flash green All night long press 101 E 262 flashes purple JE flash green Automatic brightness O short press limits brightness according to the duration of Timer to reduce energy consumption the shorter lighting time is the brighter the lighting will automatically be and vice versa 18 x Networking Alpha bollards can be networked which allows you to adjust all their settings without needing to move from one bollard to the next Each bollard should be between 1 5 m and 70 m from another bollard on the same network A network is a set of bollards that communicate by radio link and that share the following identifiers a security code and a network number For bollards to be part of the same network they therefore need to be assigned the same network number and the same security code Assigning different network numbers lets one user group bollards into separate networks according to location while retaining for instance the same security for all the bollards A network can have no security code in which case settings can be accessed directly For a bollard you have just added to a network to have the same settings as this network just go to a
12. nother bollard on the same network switch to Command Mode then press OK This bollard s settings will be applied to all the bollards on the same network including those newly added to the network To assign a network number to a bollard Add to a network long press Set flashes yellow 1 999 O enter the network number Remove from the network long press 3 flashes yellow 0 Z the bollard reverts to standalone mode If the security code is more than three digits long only the first three are taken into account 19 a Security code You can protect remote control access to the bollards with a user defined code Entering the code long press 1 999999 O enter the new code 2 flashes green als 793 flashes blue 1 999999 O repeat the new code otherwise return to Changing the code long press 1 999999 A enter the current code J flashes red dl flashes green 1 999999 A enter the new code aly 5 flashes blue 1 999999 A repeat the new code otherwise return to e Cancelling the code in the above sequence of instructions enter 000000 twice e AAAAAA or ABA BAB combinations are not accepted If either of these combinations is entered the bollard emits a red flash when QD IS pressed So you need to repeat the current step to enter a valid number After 3 unsuccessful attempts remote control access to the bollard is locked for 2 minutes and the bol
13. ns on and off automatically according to ambient luminosity Each bollard features a radio communications system enabling it to communicate with other identical bollards thereby forming a wireless network in which all the bollards have the same settings The Alpha bollard is controlled by an infrared remove control Remote access to the bollard can be protected by a user defined code 2 DECLARATION OF CONFORMITY Geoled declares that the product named Alpha bollard complies with the regulatory provisions set forth in the following essential European health and safety directives e Directive 2002 96 EC on waste electrical and electronic equipment WEEE e Directive 1999 5 EC on Radio Equipment and Telecommunications Terminal Equipment R amp TTE e Directive 2006 66 EC on batteries and accumulators and waste batteries and accumulators e Directive 2008 12 EC amending Directive 2006 66 EC on batteries and accumulators and waste batteries and accumulators e Directive 2008 103 EC amending Directive 2006 66 EC on batteries and accumulators and waste batteries and accumulators e Directive 2011 65 EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment ROHS The product has been tested according to the following standards e ETSI EN 301 489 3 2002 V1 4 1 in reference to ETSI EN 301 489 1 2011 V1 9 2 e ETSI EN 300 220 2 V2 4 1 in reference to ET SI EN 300 220 1 V2 4 1 e ETSI EN 60950 1
14. ode if one has been set 23 www geoled com
15. uggestions in Geoled s promotional catalogues are provided solely as a rough guide in other words products are installed and embedded under the sole responsibility of the customer if batteries other than those supplied or specifically recommended by Geoled are used in the products if the defect results from any unauthorized work on the products sold or if it results from an installation carried out by an unauthorized third party if the defect results from a cause unrelated to the equipment for instance a knock an act of vandalism or installation outdoors in a particularly inhospitable environment for such equipment The warranty is void if the equipment has been exposed to fire or flooding lightning or electrical damage In order to exercise their rights and on pain of forfeiture of any relevant action customers should inform Geoled in writing of the existence of defects within no more than 5 days of discovering them Under the warranty Geoled will replace electrical or electronic components recognized as defective by the technical service at no charge The warranty does not cover labour costs or any costs incurred in the following operations dismantling reassembly transport on site etc The replacement of parts does not extend the above period of warranty Furthermore if shipment of the item is delayed for any reason beyond Geoled s control the warranty period is extended accordingly such extension being limited to 3 mont
16. uration and settings 15 13 SETTINGS You control and adjust the Alpha bollard s settings with an infrared remote control supplied separately Settings should be made in sufficiently dark conditions to enable the bollard to come on automatically While adjusting settings users should pay close attention to the light signals emitted by the bollards When first brought into service bollards are standalone and thus not networked network code 0 At nightfall the bollard comes on and you can adjust the settings which will be memorized until you next adjust them Command Mode To adjust settings you first need to switch the bollard to Command Mode e Press and hold down any key for 6 seconds pointing the remote control at the bollard which should be no more than 5 metres away e The bollard will emit a short flash indicating it is now in Command Mode and ready to receive orders e lf the remote control is not used for 90 seconds the bollard emits another flash indicating it is no longer in Command Mode Sequences The bollard features two independent sequences S1 and S2 which are sets of brightness colour and other user definable parameters Networking The bollards can work in standalone mode or be networked If several bollards are networked you can control any of them with the remote control for the entire network The bollard receiving orders from the remote control transmits them to the other bollards on the same n
Download Pdf Manuals
Related Search