UC-250L2 BISS DVB-S2 Modulator User Manual
Contents
1. 2 4 Signal Cable Connections The signal cable connections consist of input and output signal cables Descriptions of the possible connection types follow below 2 4 1 ASI input and loop output cable illustration 9 37 Technologies Inc wo UC 250L2 BISS DVB S2 Modulator User s Manual 2 4 2 RF output interface connection The N type RF output interface can be found on the device s rear panel labeled RF OUT Connect this interface to the transmission equipment s RF input using coaxial cables The physical connector is illustrated below Chapter 3 Operation The UC 250L2 Modulator s front panel contains an LCD screen and navigation buttons Users can adjust the device configuration using this local interface Keyboard Function Description MENU Canceling presently entered value resuming previous setting Return to previous menu ENTER Activates the parameters that need modification or confirming the change after modification LEFT RIGHT Menu navigation UP DOWN Menu navigation LOCK Lock the screen cancel the lock state After pressing lock key the system will question the user whether to save present settings to memory If not the LCD will display the current configuration state At the Resume Factory Settings submenu users can press ENTER key to confirm a return to factory settings This will erase all current settings 10 37 e SHE GIVE w Technologies Inc 11 e UC 250L2 BIS2. UC 250L2 BISS DVB S2 Modulator User s Manual Version 2 0 Date 2014 04 26 NMS Version V4 11 E SW V6 11 HW V4 5 DISITRON INDUSTRIES INC DIRECTORY CHAPTERS 1 PRODUCT OUTLINE tedio Eva deme eoe els 1 OUTEINE m 1 l2 FEATURES una ek 1 1 3 SPEGIFIGA IONS 2 20 een 2 tnnt 3 1 5 APPEARANCE AND DESCRIPTION 112222 4 CHAPTER 2 INSTALLATION 6 2 1 ACQUISITION CHECK 2 6 2 2 INSTALLATION PREPARATION 1112 6 2 3 WIRE S CONNECTION ERROR BOOKMARK NOT DEFINED 2 4 SIGNAL CABLE CONNECTION ERROR BOOKMARK NOT DEFINED CHAPTER 3 OPERATION 10 3 1 MAIN INTERFACE 2 u ee 11 3 2 GENERAL SETTING aan 11 CHAPTER 4 NMS SETTING u a ee 24 24 4 2 SOFTWARE OPERATION sea 24 4 3 UC 250L2 BISS DVB S2 MODULATOR 31 CHAPTER 5 TROUBLESHOOTING una 36 CHAPTER 6 PACERING LIST 37 me am NN e BJ gt T Technologies Inc UC 250L2 BISS DVB S2 Modu
3. 26 37 B UC 250L2 BISS DVB S2 Modulator User s Manual Alternatively users can right click on an empty section of the left hand side column to pop up a short cut menu and selecting Add Main Freq Point Network Management System File Edit Operate Setting Help 3 lt Freq Pont Add Main Freq Point ee Add Equipment 18 Modify Property it Delete Name Inio _ Equipment Name ZIP Address FT Equipment Type Em Evorlnformations CD SystemTime 1E qupment Type Pont Address Version Hardware Version Sotware Version mi 27 37 UC 250L2 BISS DVB S2 Modulator User s Manual 4 2 4 Adding Equipment under Given Frequency Point When a Freq Point is selected users can add equipment by right clicking then selecting Add Equipment within the Edit drop down menu ra Network Hanagement Software File Edit Operate Setting Help gt E AddFregPoint CtrltE C N g Local Save g Local Load I Add Equipment Ctrl D Freq Point Sj Edit Equipment Ctrl F x Delete Equipment CtrltG ff Delete 11 Ctrl IPAddess Equipment Type Errorlnformations Hardware Version Software Version User Name admin User s Authority Admin Auto Register P Windo Googl fm 1532 in Gh NDs32 28 Netwo w 28 37 Technologies Inc 29 9e UC 250L2 BISS DVB S2 Modulator User s
4. 3 2 3 Output setting Navigating to Output Setting Menu will display the following submenus 3 1 RF Frequency 3 2 RF Level ATT 3 3 Spec Invert 3 4 RF Output 3 2 3 1 RF setting This submenu will allow users to set the RF output frequency The RF output frequency ranges from 950 to 2150MHz 3 1 RF Frequency 1000 00MHz 3 2 3 2 RF ATT Setting This submenu will allow users to set the RF output attenuation The RF attenuation ranges from 0 31 5db adjusted in 0 5db steps 3 2 RF Level ATT 305 db T 3 2 3 3 Spectrum Invert This submenu will allow users to invert the RF spectrum output 20 37 UC 250L2 BISS DVB S2 Modulator User s Manual 3 3 Spec Invert normal 3 3 Spec Invert normal 3 2 3 4 RF Output 3 4 RF Output single tone 3 4 RF Output single tone modulation This submenu will allow users to set the RF output mode for different applications Single tone The RF output is an un modulated carrier Modulation A modulated output carrier 21 37 UC 250L2 BISS DVB S2 Modulator User s Manual Spectrum Anote 3 2 4 Network setting Navigating to the Network Setting menu will display the following submenus gt 4 1 IP Address 4 2 Subnet Mask 4 3 Gateway 4 4 Console Address gt 4 5 MAC Address Note The unique MAC address is set at the factory 22 37 7 B UC 250L2 BISS DVB S2 Modulator User s Manual 4 1 IP
5. single tone Spectrum Invert Get Set 4 3 1 Modulation Mode User can select the modulators working mode and relevant constellation drop down list at this 31 37 m uem amp rn HH e lt J E U GIVE Technologies Inc e 32 e UC 250L2 BISS DVB S2 Modulator User s Manual DVB S DVB S Modulation QPSK DVB S2 QPSK DVB S Modulation QPSK DVB S2 8PSK DVB S Modulation QPSK 4 3 2 Reference Clock Internal The modulator uses internal 10MHz crystal oscillator as reference clock External The modulator uses external 10 MHz input as reference clock Auto The device will prioritize any detected external reference clock If none is present system will default to internal clock 4 3 3 Input Select ASI The input TS sourced from port 511 ASI2 The input TS sourced from port ASI2 Auto ASI1 The modulator will preferably select the input TS from if it exists otherwise it will select the input TS from ASI 2 Auto ASI2 The modulator will preferably select the input TS from ASI2 if it exists otherwise it will select the input TS from ASI 1 4 3 4 Roll off factor This submenu will allow users to select the transmission Roll Off Factor There are 3 possible options 0 35 0 25 and 0 20 4 2 5 Conv Rate When set to DVB S broadcasting the convolutional code value can be set in this sub menu The possible options are 1 2 2 3 3 4 5 6 7 8 4 2 6 FEC C
6. 250L2 BISS DVB S2 Modulator User s Manual Auto The device will prioritize any detected external reference clock If none is present system will default to internal clock 3 2 2 3 Input select 2 3 InputS elect ASI1 2 3 Input S elect 1A ASI1 ASI2 Auto ASI 1 _ Auto ASI 2 This submenu will allow users to select the input interface ASI The input TS sourced from port 511 ASI2 The input TS sourced from port ASI2 Auto ASI1 The modulator will preferably select the input TS from if it exists otherwise it will select the input TS from ASI 2 Auto ASI2 The modulator will preferably select the input TS from ASI2 if it exists otherwise it will select the input TS from ASI 1 3 2 2 4 Symbol rate 2 4 Symbol Rate 27 500M Range 0 1 45M QPSK Constellation 0 1 30M 8PSK Constellation 3 2 2 5 Roll off factor 2 5 Roll Off 0 35 2 5 Roll Off 0 35 14 37 ame EN GB e Technologies Inc i5 9 UC 250L2 BISS DVB S2 Modulator User s Manual This submenu will allow users to select the transmission Roll Off Factor There are 3 possible options 0 35 0 25 and 0 20 3 2 2 6 FEC rate Convolutional code rate 2 6 Conv Code Rate 3 A 2 6 Conv Code Rate 1 2 2 3 3 4 5 6 7 8 When set to DVB S broadcasting the convolutional code value can be set in this sub menu The possible options are 1 2 2 3 3 4 5 6 7 8 2 6 FEC Rate 1 2 2 6 FEC
7. Address 192 168 000 136 S ubnet Mask 255 255 255 000 Gateway 192 168 000 001 Console Address 192 168 000 221 MAC Address ffffffffffff 3 2 5 Saving config User can choose to save the current configured parameters by pressing ENTER key S aving please wait erasing 3 2 6 Load config gt 6 1 Load Saved CFG 6 2 Load Default CFG User can restore the device to the last saved configuration by choosing 6 1 or restore the device to factory configuration by choosing 6 2 3 2 Version User can check the hardware and software versions of the equipment in this submenu UPCOM SW 6 01 HW 4 1 23 37 Technologies Inc 9 UC 250L2 BISS DVB S2 Modulator User s Manual 3 2 8 Language Settings This submenu will allow users to set the system language 8 Language English Chapter 4 NMS Setting Network Management System Profile A Network Management System enables the remote control and monitoring of Digital TV equipment through a computer network 4 1 Installation NMS software does not require installation Extract NMS files to desired directory on local drives Two files will be generated once NMS client has been executed Network management software X XXY log preserves the log file Info Bin user configuration data 4 2 Software Operation 4 2 1 Login Interface A login interface will pop up when the software is running and give user p
8. Port After parsing input programming will display in this sub menu Users can navigate to individual programs to enable BISS scrambling 18 37 97 B UC 250L2 BISS DVB S2 Modulator User s Manual 2 01 CCTV 1 2 02 CCTV 2 2 03 CCTV 7 2 04 CCTV 10 2 05 CCTV 11 2 06 CCTV 12 2 07 CCTV MUSIC 0 01 CCTV 1 INO 3 2 2 9 2 3 ID Select This submenu will allow users to enter the encrypted session word 9 3 ID Select Device 9 3 ID Select Device 9 5 Input Data OX 00000000000000 If Device is selected enter a 14 character number to be set as one part of an encrypted session word An ESW encrypted session word is also necessary Refer to menu 3 2 2 8 2 4 for more details If Input is selected fixed data from the device will be used to encrypt programs 3 2 2 9 2 4 ESW Data 9 4 ESW Data 0X 0000000000000000 19 37 m 2 2 EH e lt J E U GIVE Technologies Inc 20 e UC 250L2 BISS DVB S2 Modulator User s Manual ESW Encrypted Session Word a 16 character number This submenu will not be visible if device is set to Device mode Users can set an ESW value together with the Input ID to complete encryption Note Once the ESW has been entered by the front panel or by the NMS client it shall become impossible to read it back through any unit interface The manual entry of the ESW shall also be in hexadecimal form the 16 digits are entered with the most significant digit first
9. their configuration file destination SaveFile tet EE 73 5620c5 ee2 6 69172 8489 4 1 c2c back coreldraw Files of type bin d Cancel Local Load oimilarly users can click the button to popup the Read File dialog box User can then choose which configuration file to load unto the device 30 37 Technologies Inc 31 UC 250L2 BISS DVB S2 Modulator User s Manual _ 3j xi Look m D gt 2 Trash root 2005 4 19 1102 flash Documents 22005 6 2 2005 6 2 test Desktop My Document er My Compute E Aoo e rU Pisces Files of type tx Cancel 4 3 UC 250L2 BISS DVB S2 Modulator Operation Users can configure the UC 250L2 Modulator in this interface Set Applies configuration to device Get Reads current device configuration Network Management Software Fie Edit Operate Setting Help G Remote Loader Remote Save Factory Setting N Restat 8 Local Save f Local Load ra UC 25012 BISS DVB S2 Modulator ip scrambling Parameters Biss Biss Program Select 32 1 H p 3204 4 DVB 52 Modulator Modulate Mode IDVB 5 Clock Input Select Roll off factor 1035 pe Conv Code Rate 172 res Pilot Insert FEC Rate gt Symbol Rate Mbaud RF RF Level ATT IF Output xi
10. Manual 4 2 5 Edit Equipment Interface Mdd Equipment 192 168 0 136 quipment Name 52 Modulatad quuipment JC 250I 2 BISS DVB S2 Modulator v Users should follow the steps as below e Enter the device IP Address Enter the device Port Number Default 2007 e Enter the desired Equipment Name Choose the correct equipment type in the drop down list of Equipment Type by clicking the Y or click symbol to automatically determine the equipment type 4 2 6 Delete Equipment Users can remove equipment from device chains by right clicking the intended target and selecting Delete in the pop up menu 29 37 UC 250L2 BISS DVB S2 Modulator User s Manual 0 Network Management sottware File Edit Operate Setting Help gt gt Remote Load Remote Save EX Factory Set lt mux scrambling Par 3211H 32041 amp Add Main Point T Add Equipment Modify Property ee 0707 4 2 7 Save Configuration Once satisfied with configured settings users can commit the changes to memory by Remote Save clicking the button on the toolbar Previous settings can be reloaded from gt gt Remote Load memory by clicking the button Users can also save and load setting configurations to their computer s hard drive e Local Save Clicking the button will pop up a Save File dialog box which will allow users to choose
11. Rate 1 2 2 6 FEC Rate 89 9 10 When set to DVB S2 QPSK broadcasting the FEC Forward Error Correction ratio can be set in this sub menu The possible rates are 1 4 1 3 2 5 1 2 3 5 2 3 3 4 4 5 5 6 8 9 9 10 2 6 FEC Rate 3 5 2 6 FEC Rate 3 5 2 3 3 4 15 37 m 2 2 EH e lt J E U GIVE Technologies Inc 16 UC 250L2 BISS DVB S2 Modulator User s Manual When set to DVB S2 8PSK broadcasting the FEC Forward Error Correction ratio can be set in this sub menu The possible rates are 3 5 2 3 3 4 5 6 8 9 9 10 3 2 2 7 Constellation This menu item only shows when MODULATOR STATE is set to DVB S2 2 7 Constellation QPSK 2 7 Constellation QPSK Users can choose between QPSK or 8PSK constellations 3 2 2 8 Pilot Insert This menu item only shows when MODULATOR STATE is set to DVB S2 2 8 Pilot Insert Off 2 8 Pilot Insert User can choose whether to insert the Pilot block 3 2 2 9 BISS Setting BISS Basic Interoperable Scrambling System There are three available BISS Scrambling modes 0 1 amp E Sub menus will vary depending on mode selection Mode 0 is equivalent to OFF or unscrambled Free to Air programming 9 1 Biss Mode Mode O 16 37 NM NE amm HEN e JE U Technologies Inc 5 9 UC 250L2 BISS DVB S2 Modulator User s Manual 9 1 Biss Mode Modes 1 and E will enable BISS scramblin
12. S DVB S2 Modulator User s Manual 3 1 Main Interface The front panel LCD first row will display Company Name Device Type and real time input bit rate in the The second will display output RF frequency Symbol Rate and FEC ratio Forward Error Correction UPCOM UC 250L2 BISS TS 05 654Mbps R F 1000 00MHz Symb Rate 27 500M Conv 3 4 UPCOM UC 250L2 BISS TS 05 654Mbps 1000 00 Symb Ratez27 500M FEC 3 4 3 2 General setting Pressing the LOCK key will unlock the front panel and display the following menus 1 Alarm Status 2 System Setting 3 Output Setting 4 Network S etting 5 Saving Config 6 Loading Config 7 Version 8 Language By pressing UP or DOWN key to the specified menu item then pressing ENTER to enter the submenu as following pages Users can navigate to the desired menus by using the UP DOWN LEFT RIGHT and ENTER control buttons 3 2 1 Alarm Status Temperature 34 Centidegree Alarm Count 0 11 37 m 2 2 EH e lt J E U GIVE Technologies Inc 2 UC 250L2 55 DVB S2 Modulator User s Manual 3 2 1 1 Temperature The figure displayed in the first row shows the real time device housing temperature 3 2 1 2 Alarm count The Alarm count in the second row indicates the number of alarms Whenever an abnormal event happens the number will increase 3 2 1 3 Alarm descriptions Users can navigate to this submenu to check alarm details The alarm types are describ
13. ed below 1 Ref Clock Lose The modulator cannot detect external 10MHZ reference clock input No input TS There is no detected ASI signal input Input TS Overflow Input TS bit rate over transmission bandwidth limit Internal error Internal device error ec om p N Temperature Alarm When the modulators housing temperature exceeds normal range Temperature 34 Centidegree Alarm Count 4 1 Ref Clock Lose 2 No input TS 4 Internal Error 5 Temperature Alarm 12 37 m NEU amp Bas e SEE Technologies Inc 13 e UC 250L2 BISS DVB S2 Modulator User s Manual 3 2 2 System setting Navigating to the System Setting Menu will display the following submenus Alarm S tatus 2 2 REF Clock Sel Input S elect 2 4 Symbol Rate R oll O ff 2 6 Conv Code Rate Constellation 2 8 Pilot Insert gt 2 9 Biss Setting 3 2 2 1 Modulation Mode 2 1 Modulate Mode DVB S 2 1 Modulate Mode DVB S This submenu will allow user to choose between DVB S and DVB S2 broadcasting DVB S QPSK DVB S Modulation DVB S2 8PSK or QPSK BISS DVB S2 Modulation 3 2 2 2 Reference Clock Select 2 2 REF Clock Sel internal 2 2 REF Clock Sel internal external Internal The modulator uses internal 10MHz crystal oscillator as reference clock External The modulator uses external 10 MHz input as reference clock 13 37 m 2 2 EH e lt J E U GIVE Technologies Inc 14 e UC
14. g Mode 1 will require a session word Mode E will require an encrypted session word 3 2 2 9 1 Mode 1 The following sub menus will be available under Mode 1 scrambling 9 1 Biss Mode 9 2 Input P ort 00 9 3 SW Data 3 2 2 9 1 1 Biss Mode 9 1 Biss Mode Mode 1 This submenu will display the currently selected BISS mode 3 2 2 9 1 2 Input Port After parsing input programming will display in this sub menu Users can navigate to individual programs to enable BISS scrambling 2 01 CCTV 1 2 02 CCTV 2 2 03 7 2 04 CCTV 10 2 05 CCTV 11 2 06 CCTV 12 2 07 CCTV MUSIC 0 01 CCTV 1 INO 17 37 m NEU amp Bas e SEE T Technologies Inc 18 e UC 250L2 BISS DVB S2 Modulator User s Manual 3 2 2 9 1 3 SW Data 9 3 SW Data OX 000000000000 9 3 SW Data OX 000000000000 SW Session Word a fixed 12 character number User can set a session word for scrambling control Once the SW Session Word has been set a 64 bit CW Control Word will be derived from the SW according to the DVB CSA common scrambling algorithm specification Note Enter hexadecimal values 3 2 2 9 2 Mode E When the modulator is set to Mode E the display will show the following 9 1 Biss Mode 9 2 Input P ort 00 9 3 ID Select 9 4 ESW Data 3 2 2 9 2 1 Biss Mode 9 1 Biss Mode Mode E This sub menu will show the currently selected BISS scrambling mode Press ENTER to change mode 3 2 2 9 2 2 Input
15. her with the Input ID to complete encryption Note Once the ESW has been entered by the front panel or by the NMS client it shall become impossible to read it back through any unit interface The manual entry of the ESW shall also be in hexadecimal form the 16 digits are entered with the most significant digit first 4 2 12 1 SW Data 3 2 2 8 1 3 SW Session Word a fixed 12 character number User can set a session word for scrambling control Once the SW Session Word has been set a 64 bit CW Control Word will be derived 34 37 ame EN GB e Technologies Inc e 35 0 UC 250L2 BISS DVB S2 Modulator User s Manual from the SW according to the DVB CSA common scrambling algorithm specification Note Enter hexadecimal values 4 2 12 3 Input ID 3 2 2 8 2 3 In this interface user can set the input ID 4 2 12 4 Word Mode 3 2 2 8 There are three possible options provided to be selected ModeO Mode 1 and Mode E User can refer to 3 2 2 8 for more details 4 2 12 5 Select ID 3 2 2 8 2 3 There are two possible options provided to be selected Input and Device User can refer to 3 2 2 8 2 3 for more details 4 2 13 BISS Program Select lt lt UC 250L2 BISS DVB S2 Modulator Parameters Biss Biss Program Select Refresh Input Refresh Output Dasein Timeout sec In this interface user can decide the programs need to be scrambled by selecting the items in the left col
16. ir grounding cables are properly secured Current pass through should be tested Anti rust should be applied on all relevant connections Do not include any other devices in this unit s grounding circuit The minimum contact patch area between the grounding wire and the device s frame should be no less than 25mm 2 2 4 Frame Grounding All the machine frames should be connected with protective copper strip The grounding wire should be as short as possible and avoid circling The minimum contact patch area between the grounding wire and the device s frame should be no less than 25mm 2 2 2 5 Device Grounding Connect the device s grounding point to the rack s grounding pole with copper wire 8 37 e 2 2 EDEN e SEE Technologies Inc Pe UC 250L2 BISS DVB S2 Modulator User s Manual 2 3 Grounding Wire Connection The grounding wire conductive screw is located on the device s rear panel adjacent to the AC Plug connector Connecting Power Cord User should insert one end into power supply socket and the other end into device s AC power source Connecting Grounding Wire If possible connect the device s grounding wire in an unshared circuit If the grounding circuit is to be shared with other devices the grounding resistance should be equal to or less than 10 Caution Before connecting power cord to UC 250L2 BISS DVB S2 Modulator user should set the power switch to OFF
17. lation is QPSK Up Down Left Up Down Left RightiConfirmation ey 000000000000 key Locking key 4 37 Rear Panel Illustration RF OUT 100V 240V 50 60Hz 1A 10MHz IN 10MHz OUT am ASI2 LOOP OUT LOOP our Ethernet 5 37 e SEE Technologies Inc e 602 UC 250L2 55 DVB S2 Modulator User s Manual Chapter 2 Installation Guide 2 1 Initial Check When first opening the device packaging please check contents against the following list e UC 250L2 BISS DVB S2 Modulator ASI Cable e Power Cord If any item is missing please contact your point of purchase 2 2 Installation Please follow all installation instructions included in this chapter Users can refer to the rear panel chart during installation The main content of this chapter include Checking the device for shipping damage Preparing relevant environment for installation Installing UC 250L2 Modulator Connecting signal cables Connecting communication port optional 6 37 amp e B UC 250L2 BISS DVB S2 Modulator User s Manual 2 2 1 Device Installation Flow Chart Illustration Connecting G rouding Acquisition Fixing Wire and Connecting S etting Running Check Device S ignal Wire Parameter Device Power C ord 2 2 2 Environmental Requirements The distance between any 2 devices should be 1 2 1 5m Walls Datacenter should be no closer than 0 8m Electric Is
18. lator User s Manual Chapter 1 product outline 1 1 Outline The Upcom UC 250L2 BISS DVB S2 Modulator is a professional grade modulation device developed according to EN302307 DVB S2 second generation European broadcast standard It adopts advanced framing structure channel coding and modulation methods which increases the device s transmission ability by more than 5096 over previous generation DVB S modulators under the same broadcast conditions It will also provide better reception ability in the same spectral efficiency The device is backwards compatible with DVB S EN300421 modulation standards The device can be controlled locally through front panel a LCD screen and navigation buttons or remotely through a NMS client 1 2 Features Fully complies with DVB S2 EN302307 modulation standard Backwards compatible with DVB S EN300421 modulation standard Two ASI inputs supporting automatic switchover in case of signal loss Supports BISS scrambling modes 0 1 amp E Supports local and remote control Output level attenuation control 10MHz outer reference clock input Output frequency range 950 2150MHz Full size front panel LCD display and navigation buttons 1 37 1 3 Specifications Supports both packet and byte mode TS inputs MPEG TS Input RF Output Channel Coding and Modulation Miscellaneous UC 250L2 BISS DVB S2 Modulator User s Manual Supports 188 204Byte transmission stream packets Two ASI inpu
19. ode Rate When set to DVB S2 QPSK broadcasting the FEC Forward Error Correction ratio can be set in this sub menu The possible rates are 1 4 1 3 2 5 1 2 3 5 2 3 3 4 4 5 5 6 8 9 9 10 32 37 m uem amp rn HH e lt J E U GIVE Technologies Inc 37 UC 250L2 55 DVB S2 Modulator User s Manual 4 2 7 Pilot Insert User can choose whether to insert the Pilot block in the check box 4 2 8 Symbol Rate Range 0 45M QPSK Constellation 0 30M 28PSK Constellation 4 2 9 RF ATT User can set the attenuation of the RF output The RF attenuation range is from 0 31 5db in 0 5db steps 4 2 10 Modulation On Optional User can set the RF output mode for different applications Single tone the RF output is an un modulated carrier Modulation The RF output is a modulated carrier Off Turn off the RF output 4 2 11 RF User can set RF output frequency The RF output frequency ranges from 950 to 2150MHz 33 37 e BWI U uJ rE Technologies Inc e 34 UC 250L2 BISS DVB S2 Modulator User s Manual 4 2 12 BISS lt lt UC 250L2 BISS DVB S2 Modulator Parameters Biss Biss Program Select ESW Data Ox SW Data x Input ID Word 0 Mode 0 Select ID Device v Get Set 4 2 12 1 ESW Data 3 2 2 8 2 4 ESW Encrypted Session Word a 16 character number This submenu will not be visible if device is set to Device mode Users can set an ESW value toget
20. olation Dust Free Volume resistivity of ground anti static material 1X10 1X10 9 Grounding current limiting resistance 1M Floor bearing should be greater than 450Kg m Datacenter Floor Environment 5 40 sustainable 0 45 short term Temperature Installing air conditioning is recommended Relative Humidity 2096 8096 sustainable 1096 9096 short time Installing rubber strips for sealing door gaps and dual pane Door amp Window glasses for windows is recommended Fire Protection Fire alarm system and extinguishers are required Ensure air conditioning lighting and device power sources are on Power different circuits Device requires AC power 100 240V 50 60Hz Please carefully check before running 7 37 3 mE amm ge ee e BJ gt Technologies Inc 9 UC 250L2 BISS DVB S2 Modulator User s Manual 2 2 3 Grounding Requirement Good grounding practices will ensure the proper function and long term reliability of the device This will provide protection from power surges and interference It is imperative the unit is used only when properly grounded Coaxial cable s outer conductor and isolation layers should keep proper electric conduction with the device s metal housing Grounding wires must contain copper conductors in order to reduce high frequency impedance The grounding wire must also be as thick and as short as possible Users should make sure the two terminations of the
21. rompts to input user name and password User Sign In UserName admin Password Auto Register 24 37 e User can login the NMS by pressing Confirm key after inputting user name and password Default username and password is admin 4 2 2 Main Interface 3 Network Hanagement Software File Edit Operate Setting Help gt mi NN gj LocalSave f Local Load lt Point IPAddress fa Equipment Type Emorinfomations SystemTime Hardware Version Software Version lt E User Name admin User s Authority Admin Auto Register no P This software will allow the user to edit various parameters in the device tree for management and classification 25 37 UC 250L2 BISS DVB S2 Modulator User s Manual 4 2 3 Adding Frequency Point Eek 71 Network Management Software Help File Operate Setting iy Setting 9 Restat 8 LocalSave Local Load 1 Undo gt Redo Add Equipment Ctrl D lt Freq Point Edit Equipment Ctrl F X Delete Equipment CtrltG ff Delete all Ctrl H lPAddess Equipment Type Emodnfomation SystemTime Ez3HardWw are Version E Software Version ei User Name admin User s Authority Admin Auto Register no a To begin add a Frequency Point This can be done by clicking Add Freq Point within the Edit drop down menu AddFregPoint
22. ts supporting auto switchover ASI input connector BNC impedance 750 Frequency is adjustable from 950 to 2150MHz Output Level attenuation is adjustable from 0 to 31 5 dB in steps of 0 5 dB Maximum Output level OdBm MER232dB Connector N type impedance 500 DVB S DVB S2 Outer coding RS coding BCH coding Inner coding Convolutional LDPC coding 1 2 3 5 2 3 3 4 4 5 5 6 8 9 Code Rat 1 2 2 3 3 4 5 6 7 8 9 10 Constellation QPSK QPSK 8PSK Roll off Factor 0 2 0 25 0 35 0 2 0 25 0 35 0 1 30M 8PSK 0 1 45 M QPSK BISS Scramble pe ModeO Mode1 Mode E Dimension 44mmx482mmx410mm Environmental 0 45 operation 20 80 storage Power 100 240VAC 10 50Hz 60Hz Symbol Rate 0 1 45MBaud 2 37 e e Technologies Inc 75 UC 250L2 BISS DVB S2 Modulator User s Manual 1 4 Principle chart 1OMHz 10MHz hr Modulating ASI interface ASI interface CPU control LCD KEY RJ45 3 37 UC 250L2 BISS DVB S2 Modulator User s Manual 1 5 Appearance and description Front Panel Illustration UC 250L2 BISS DVB S2 Modulator LCD LCD display 005050500000 10M 10MHZ Ext40M 10MHZOuterRefereneClok Reference Clock ASI1 512 512 E TS Overflow ER TS bit rate over the Transmission bandwidth Indicators Alarm ELI Indicator DVB Current Modulation is DVB S2 DVB EDS Current Modulation is DVB S EE Current constellation is 8PSK EE Current constel
23. umn and then clicking the button to put them in the right column User can also remove the selected programs to left column by clicking 35 37 mm 2 2 RH e lt J E U GIVE Technologies Inc 57 UC 250L2 55 DVB S2 Modulator User s Manual button It is necessary to set a timeout value for parsing program here bigger values are recommended so that more programs have enough time to be parsed After finished the selection use can click Parse In to confirm Chapter 5 Troubleshooting Our 1509001 quality assurance program has been approved by the All Upcom products pass testing and inspection before shipment Please follow all instructions in this manual for proper device operation Immediately Unplug the device if Power cord or socket damage occurs Any liquid flowed into the device Any dust causes a short circuit Device is present in a damp environment Device suffers from physical damage Long term idle periods are planned Maintenance is needed Longtime idle After switching on and restoring to factory setting device still cannot work properly e Maintenance needed 36 37 e Technologies Inc 37 0 UC 250L2 BISS DVB S2 Modulator User s Manual Chapter 6 Packing List e UC 250L2 BISS DVB S2 Modulator 1pcs Power cord 1pcs ASI Cable 1pcs 37 37
Download Pdf Manuals
Related Search