User`s Manual - PLANET Technology Corporation.
Contents
1. 2 2 Rear Panel The rear panel of the FNSW 1600P PoE Fast Ethernet Switch indicates an AC inlet power socket which accepts input power from 100 to 240V AC 50 60Hz 2A Figure 2 2 FNSW 1600P Switch Rear Panel The device is a power required device it means it will not work till it is powered If your networks should active all the time please ga consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime In some area installing a surge suppression device may also help Notice to protect your FNSW 1600P from being damaged by unregulated surge or current to the FNSW 1600P or the power adapter 3 Hardware Installation Start up Please refer to the followings for your cabling 10 100Base TX All 10 100Base TX ports come with Auto Negotiation capability They automatically support 100Base TX and 10Base T networks Users only need to plug a working network device into one of the 10 100Base TX ports and then turn on the FNSW 1600P The port will automatically runs in 10Mbps 20Mbps 100Mbps or 200Mbps after the negotiation with the connected device Cabling Each 10 100Base TX ports use RJ 45 sockets similar to phone jacks for connection of unshielded twisted pair cable UTP The IEEE 802 3 802 3u Fast Ethernet standard requires Category 5 5e UTP for 100Mbps 100Base TX 10Base T networks can use Cat 32. 16 Port 10 100Mbps PoE Fast Ethernet Switch FNSW 1600P User s Manual Trademarks Copyright PLANET Technology Corp 2011 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comply with the limits for a Class A di
3. 2001 A2 2003 IEC 61000 4 2 2008 IEC 61000 4 3 2006 A1 2007 A2 2010 IEC 61000 4 4 2004 A1 2010 IEC 61000 4 5 2005 IEC 61000 4 6 2008 IEC 61000 4 8 2009 IEC 61000 4 11 2004 Responsible for marking this declaration if the Manufacturer O Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang Position Title Product Manager i E fro Taiwan 24 Oct 2011 Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw http www planet com tw 10F No 96 Minquan Rd Xindian Dist New Taipei City Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528
4. 4 5 see table below Maximum distance is 100meters 328 feet Port Type Cable Type Connector 10Base T Cat 3 4 5 2 pair RJ 45 100Base TX Cat 5 5e UTP 2 pair RJ 45 Any Ethernet devices like hubs PCs can connect to the FNSW 1600P by using straight through wires The 16 10 100Mbps ports are auto MDI MDI X can be used on straight through or crossover cable 3 1 Desktop Installation To install the PoE Fast Ethernet Switch on desktop simply follow the next steps Step 1 Attach the rubber feet to the recessed areas on the bottom of the PoE Fast Ethernet Switch as shown in Figure 3 1 Figure 3 1 Attaching the Rubber Feet to the PoE Fast Ethernet Switch Step 2 Place the PoE Fast Ethernet Switch on desktop near an AC power source Step 3 Keep enough ventilation space between the PoE Fast Ethernet Switch and the surrounding objects When choosing a location please keep in mind the environmental restrictions discussed in Chapter 1 Section 4 in Specification Step 4 Connect your PoE Fast Ethernet Switch to 802 3af complied Power Devices PD and other network devices A Connect one end of a standard network cable to the 10 100 RJ 45 ports at front panel of the PoE Fast Ethernet Switch B Connect the other end of the cable to the network devices such as printer servers workstations or routers etc Connection to the Switch requires UTP Category 5 5e 6 network cabling wit
5. 8 to carry power the other four is for data transmit mE End Span End Span device is direct connecting with power device End Span could also tap the wire 1 2 and 3 6 PoE System Architecture The specification of PoE typically requires two devices the Powered Source Equipment PSE and the Powered Device PD The PSE is either an End Span or a Mid Span while the PD is a PoE enabled terminal such as IP Phones Wireless LAN etc Power can be delivered over data pairs or spare pairs of standard CAT 5 cabling How is Power Transferred Through the Cable A standard CAT5 Ethernet cable has four twisted pairs but only two of these are used for 10BASE T and 100BASE T The specification allows two options for using these cables for power shown in Figure 2 and Figure 3 The spare pairs are used Figure 2 shows the pair on pins 4 and 5 connected together and forming the positive negative supply and the pair on pins 7 and 8 connected and forming the positive negative supply In fact a late change to the spec allows either polarity to be used POWER SOURCING POWERED DEVICE EQUIPMENT PSE PD SPARE PAIR 1 1 SIGNAL PAIR SIGNAL PAIR 7 7 SPARE PAIR Figure 1 Power Supplied over the Spare Pins The data pairs are used Since Ethernet pairs are transformer coupled at each end it is possible to apply DC power to the center tap of the isolation transformer without upsetting the data transfer In this mode of opera
6. E 802 3af 17 H _ Appendix A Networking Connection A 1 DATA OUT PoE Switch RJ 45 Port Pin Assignments PIN NO RJ 45 SIGNAL ASSIGNMENT Output Transmit Data Output Transmit Data 12345678 Receive Data Negative Power Negative Power Receive Data Positive Power O NX D UI A U N r o o o o o ojo Oo Positive Power A 2 10 100Mbps 10 100Base TX When connecting Switch to another Fast Ethernet switch a straight or crossover cable might necessary Each port of the Switch supports auto MDI MDI X detection That means you can directly connect the Switch to any Ethernet devices without making a crossover cable The following table and diagram show the standard RJ 45 receptacle connector and their pin assignments RJ 45 Connector pin assignment Contact E RI E oe Media Dependant Interface Media Dependant Interface Cross Tx transmit Rx receive Tx transmit Rx receive Rx receive Tx transmit 4 5 Not used 6 Rx receive Tx transmit 7 8 Not used The standard cable RJ 45 pin assignment MO The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection Straight Cable 12345678 Crossover Cable 12345678 12345678 SIDE 1 1 W
7. e steps 4 and steps 5 of session 3 1 Desktop Installation to connect the network cabling and supply power to your Switch 3 3 Product Application Department Workgroup PoE Switch Providing 16 Port PoE in line power interfaces the FNSW 1600P can easily build a power centrally controlled IP phone system IP Camera system and Wireless AP group for the enterprise Cameras can be installed around the corner in the company or campus for surveillance demands or Wireless AP to build a wireless roaming environment in the office Without the power socket limitation the Switch makes the installation of cameras or Wireless AP more easily and efficiently PoE IP Camera Non PoE Camera PoE Splitter IP Camera PoE IP Camera T PoE IP Camera P Camera Campus Centre of Surveillance PoE IP Camera i 100Base TX UTP H 100Base TX UTP with PoE Power Line DC Figure 3 4 Department Workgroup PoE Switch Connection 3 4 Power over Ethernet Powered Device Voice over IP phones Enterprise can install POE VoIP Phone ATA and other Ethernet non Ethernet end devices to the central where UPS is installed 3 5 Watts for un interrupt power system and power control system Wireless LAN Access Points Museum Sightseeing Airport Hotel Campus Factory Ware house can install the Access Point any where with no hesita 6 12 Watts tion a _ IP Surveillance Te A Enterprise Museum Campus Hosp
8. er ation O Integrates address look up engine supporting 8K absolute MAC addresses O Automatic address learning and address aging Hardware O 19 inch size 1U height O LED indicators for PoE ready and PoE activity O 2 silent FAN to provide stable and efficient power performance 1 4 Specification Model FNSW 1600P 16 Port 10 100Mbps PoE Fast Ethernet Switch Hardware Specification Network Connector PoE Inject Port 16 Port RJ 45 for 10 100Base TX 16 Port with 802 3af PoE injector function LED Display System Power Green Per port PoE Orange LNK ACT Green Switch Architecture Store and Forward switch architecture MAC Address 8K MAC address table with Auto learning function Switch Fabric 3 2Gbps Switch Throughput 2 38Mpps 64Bytes Power Requirement AC 100 240V 50 60Hz 2A max Power Consumption Max 135 Watts 460 BTU Dimension W x D x H Weight 445 x 207 x 45 mm 1U height 2 33kg Power over Ethernet PoE Standard IEEE 802 3af Power over Ethernet PSE PoE Power Supply Type Mid Span PoE Power Output Per Port 48V DC 350mA Max 15 4 Watts Power Pin Assignment 4 5 7 8 PoE Power Budget 125 Watts Standard Conformance EMI Safety FCC Class A CE Standard Compliance IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3x Flow Control IEEE 802 3af Power over Ethernet Env
9. gital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Energy Saving Note of the Device This power required device does not support Standby mode operation For energy saving please remove the power cable to disconnect the device from the power circuit Without removing power cable the device will still consuming power from the power source In the view of Saving the Energy and reduce the unnecessary power consuming it is strongly suggested to remove the power connection for the device if this device is not intended to be active WEEE Warning To avoid the potential effects on the environment and human health as a K result of the presence of hazardous substances in electrical and electronic m quipment end users of electrical and electronic equ
10. h RJ 45 tips For more information please see the Cabling Specification in Appendix A Step 5 Supply power to the PoE Fast Ethernet Switch A Connect one end of the power cable to the PoE Fast Ethernet Switch B Connect the power plug of the power cable to a standard wall outlet When the PoE Fast Ethernet Switch receives power the Power LED should remain solid Green 3 2 Rack Mounting To install the PoE Fast Ethernet Switch in a 19 inch standard rack follow the instructions described below Step 1 Place your PoE Fast Ethernet Switch on a hard flat surface with the front panel positioned towards your front side Step 2 Attach a rack mount bracket to each side of the PoE Fast Ethernet Switch with supplied screws attached to the package Figure 3 2 shows how to attach brackets to one side of the PoE Fast Ethernet Switch Figure 3 2 Attaching the Brackets to the PoE Fast Ethernet Switch You must use the screws supplied with the mounting brackets Damage caused to the parts by using incorrect screws would invali date the warranty Step 3 Secure the brackets tightly Step 4 Follow the same steps to attach the second bracket to the opposite side Step 5 After the brackets are attached to the Switch use suitable screws to securely attach the brackets to the rack as shown in Figure 3 3 at 00880000 Figure 3 3 Mounting the PoE Fast Ethernet Switch in a Rack Step 6 Proceeds with th
11. hite Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Green 2 Green 3 White Orange 4 Blue 5 White Blue 6 Orange 7 White Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 19 H _ Q PLANET Networking amp Communication EC Declaration of Conformit For the following equipment Type of Product FNSW 1600P Model Number 16 Port 10 100Base TX PoE Fast Ethernet Switch Produced by Manufacturers Name Planet Technology Corp Manufacturer s Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied EN 55022 2006 A1 2007 Class A EN 61000 3 2 2006 A2 2009 EN 61000 3 3 2008 EN 55024 1998 A1
12. ides the 802 3x Full Duplex flow control function of the FNSW 1600P enables PD devices and servers directly connect to the Switch for wire speed packet transfer performance without risk of packet loss Easy Cable Connection With data and power over Ethernet from one unit the FNSW 1600P shall reduce cables and eliminates the need for dedicated electrical outlets on the wall ceiling or any unreachable place A wire carries both data and power lowering the installation costs simplifying the installation effort and eliminating the need for electricians or extension cords With 125Watts Power Budget the FNSW 1600P is ideal for small business and workgroups requiring to deploy the PoE for the wireless access points IP based surveillance camera or IP phones in any places easily efficiently and cost effective 1 3 Features RJ 45 Interface O 16 Port 10 100Mbps Fast Ethernet ports O Each Ethernet port supports 48V DC power to PoE Powered Device Power over Ethernet O Comply with IEEE 802 3af Power over Ethernet Mid Span PSE O Up to 16 IEEE 802 3af devices powered O PoE Power Budget 125 Watts O Supports PoE Power up to 15 4 Watts for each PoE port O Auto detect powered device PD O Circuit protection prevents power interference between ports O Remote power feeding up to 100m Switching O Hardware based 10 100Mbps Auto Negotiation and Auto MDI MDI X O Flow control for Full Duplex operation and back pressure for Half Duplex op
13. ipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET 16 Port 10 100Mbps PoE Fast Ethernet Switch User s Manual For Model FNSW 1600P Revision 1 1 November 2011 Part No 2351 A50170 001 Table of Contents 1 o arene eE Oa EREA 5 dl Enel i 5 1 2 Product Descrip ii 5 1 3 EAU as 6 Sl nine aa E a O aE EE A E Aaa 7 2 Hardware DESGHIPUON sseni anA EA PEE NEES i 8 2l Front Paheli A EN 8 2 AA LED Ain A pana AaS 8 2 2 Rear Palais 9 3 Hardware Installation iaa sala 10 3 1 Desktop installation 10 3 2 Rack MOUNN inicia A a 11 3 3 PFOQUCE APPlNGatlOM ii taa 12 3 4 Power over Ethernet Powered Device oconcoccononnononcnnnnnonconenconionenconanannns 13 4 Power over Ethernet OVEFVIEW sieaiciesssesencesdondecianusndesicciants ext hurneseavvardseendendera ds 14 5 MPOUDICSHOOUING ii cdc ssecscecnantacciedteanaisetedsoecadavecaiadcasananecansesaie ida aaa 17 Appendix A Networking CONNECTION soci indi a dadas 18 A 1 DATA OUT PoE Switch RJ 45 Port Pin AssignhMentS ccococcnccnnoncncnnnoninnnnns 18 A 2 10 100Mbps 10 100Base TX issii srisrsisisio ninas ne a anda e sai e 18 1 Introduction 1 1 Checklist Check the contents of your package for following parts FNSW 1600P x 1 User s Manual x 1 e Power Cord x 1 Rubber Feet x 4 e Two Rack mounting Brackets with Attachme
14. ironment Operating environment 0 50 Degree C Storage environment 40 70 Degree C Operating Humidity 5 95 relative humidity non condensing Storage Humidity 5 95 relative humidity non condensing 2 Hardware Description This product provides two different running speeds 10Mbps and 100Mbps in the same switch and automatically distinguishes the speed of incoming connection This section describes the hardware features of FNSW 1600P For easier management and control of the Switch familiarize yourself with its display indicators and ports Front panel illustrations in this chapter display the unit LED indicators Before connecting any network device to the FNSW 1600P please read this chapter carefully 2 1 Front Panel The Front Panel of the FNSW 1600P PoE Fast Ethernet Switch consists of 16 x Auto Sensing 10 100Mbps Ethernet RJ 45 Ports The LED Indicators are also located on the front panel of the FNSW 1600P Figure 2 1 FNSW 1600P Switch Front Panel 2 1 1 LED Indicators System LED Color Function PWR Green Light Indicate the Switch has power Per 10 100Mbps Port LED Color Function Light Indicate the port is providing 48V DC in line power PoE In Use Orange Light Indicate the link through that port is successfully established Blink Indicate that the Switch is actively sending or receiving data over that port LNK ACT Green
15. ital Bank can install IP Camera without limits of install location no need electrician 10 12 Watts to install AC sockets PoE Splitter i PoE Splitter split the PoE 48V DC over the Ethernet cable into 5 12V DC power output It frees the device deployment from restrictions due to power outlet locations which eliminate the 312 Watts costs for additional AC wiring and reduces the installation time 13i 4 Power over Ethernet Overview What is PoE Based on the global standard IEEE 802 3af PoE is a technology for wired Ethernet the most widely installed local area network technology adopted today PoE allows the electrical power necessary for the operation of each end device to be carried by data cables rather than by separate power cords New network applications such as IP Cameras VoIP Phones and Wireless Networking can help enterprises improve productivity It minimizes wires that must be used to install the network for offering lower cost and less power failures IEEE 802 3af also called Data Terminal equipment DTE power via Media dependent interface MDI is an international standard to define the transmission for power over Ethernet The 802 3af is delivering 48V power over RJ 45 wiring Besides 802 3af also define two types of source equipment Mid Span and End Span m Mid Span Mid Span device is placed between legacy switch and the powered device Mid Span is tap the unused wire pairs 4 5 and 7
16. nt Screws x 8 If any of these pieces are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair In the following section the term PoE Fast Ethernet Switch means the Switch device ie FNSW 1600P term of switch can be any third switches 1 2 Product Description Centralized Power Distribution for Ethernet Networking To fulfill the demand of sufficient PoE power for network applications with Gigabit speed transmission PLANET introduces a new member in the 802 3af PoE Fast Ethernet Switch family FNSW 1600P the 16 Port 10 100Mbps 802 3af Power over Ethernet Switch with 125 Watts PoE budget The 16 x 802 3af PoE ports provide PoE power injector function which is able to drive at least 9 x IEEE 802 3af 12 95 Watts Class 3 compliant powered devices The FNSW 1600P also provides a simple cost effective and non blocking wire speed performance with 19 inch metal shape for deployment in compact housing SOHO office or department network application Great Ethernet Traffic Transmission Ability The FNSW 1600P features high performance switch architecture capable of providing the non blocking 3 2Gbps switch fabric and wire speed throughput as high as 2 38Mpps which greatly simplifies the tasks of upgrading the LAN for catering to increasing bandwidth demands Bes
17. olution Check the cable connection and remove duplex mode of the PoE Fast Ethernet Switch Performance is bad Solution Check the full duplex status of the Switch If the PoE Fast Ethernet Switch is set to full duplex and the partner is set to half duplex then the performance will be poor 100Base TX port link LED is light but the traffic is irregular Solution Check that the attached device is not set to dedicate full duplex Some devices use a physical or software switch to change duplex modes Auto negotiation may not recognize this type of full duplex setting Why the Switch doesn t connect to the network Solution Check the LNK ACT LED on the switch Try another port on the PoE Fast Ethernet Switch Make sure the cable is installed properly Make sure the cable is the right type Turn off the power After a while turn on power again Why connects PoE device to FNSW 1600P and it cannot power on Solution Please check the cable type of the connection from FNSW 1600P to the other end The cable should be an 8 wire UTP Category 5 or above EIA568 cable within 100 meters A cable with only 4 wire short loop or over 100 meters all will affect the power supply Please check and assure the device that fully complied with IEEE 802 3af standard What is the power output of each IEEE 802 af PoE port Solution Each PoE port supports 48V DC 350mA max 15 4 Watts power output Detect and inject by the standard of IEE
18. tion the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity POWER SOURCING POWERED DEVICE EQUIPMENT PSE PD SPARE PAIR 1 A SIGNAL PAIR SIGNAL PAIR 7 SPARE PAIR Figure 2 Power Supplied over the Data Pins When to install PoE Consider the following scenarios e You re planning to install the latest VoIP Phone system to minimize cabling building costs when your company moves into new offices next month e The company staff has been clamoring for a wireless access point in the picnic area behind the building so they can work on their laptops through lunch but the cost of electrical power to the outside is not affordable e Management asks for IP Surveillance Cameras and business access systems throughout the facility but they would rather avoid another electrician s payment References IEEE Std 802 3af 2003 Amendment to IEEE Std 802 3 2002 including IEEE Std 802 3ae 2002 2003 Page s 0_1 121 White Paper on Power over Ethernet IEEE 802 3af http www poweroverethernet com articles php article_id 52 Microsemi PowerDsine http www microsemi com PowerDsine Linear Tech http www linear com 5 Troubleshooting This chapter contains information to help you solve issues If the PoE Fast Ethernet Switch is not functioning properly make sure the PoE Fast Ethernet Switch was set up according to instructions in this manual The Link LED is not light S
Download Pdf Manuals
Related Search