Pro-Ject Set “Micro-Hifi-System”
Contents
1. BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Set Micro Hifi System Dear music lover thank you for purchasing a Pro Ject Micro Hifi System Set In order to achieve maximum performance and reliability you should study these instructions for use carefully WV Warning of a hazard for the user the units or possible misuse S Important notice Safety instructions AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on the power supply The power cord power supply is used to disconnect the unit from the mains Make sure that the power cord power supply is easily accessible at all times Never handle the device the power WV cord power supply while your hands are wet or damp Avoid letting liquids enter the device or the power supply Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device or the power supply Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions What s in the box Receiver Box S including remote control handset power supply and power cord Dock Box S Fi including remote control handset and power supply CD Box S including remote control handset and power supply2. Control it remote control handset 2 x Speaker Box 5 including wall mount brackets and instruction for use Design Box 4iP Acryl Speaker cable length 2 x 3 meter 8 x banana plugs 4mm Interconnect cables length 20 and 25cm Receiver Box CE RoHS a Ant R power b 20V C eo INT 75 Pro Ject Audio Systems o Austria 0 0 WV Make all connections whilst the receiver is disconnected from the power supply 2 Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Connecting receiver docking station and CD player Connect using the supplied interconnect cables the sockets INT on the receiver to the sockets OUT on the CD Box S The sockets OUT of the Dock Box S Fi have to be connected to the sockets IN2 on the receiver WV Take care to connect the left and right channels correctly The right channel is usually marked red the left channel black or white Antenna input Connects any antenna cable with a co axial DIN plug US model F plug Connecting receiver and speakers The output terminals accept loudspeaker cables terminated with 4mm Banana plugs spades connectors or naked wire Connect the cable terminals on the receiver to the terminals on the speakers The red speaker terminals carry the positive signal the black speaker terminals the negative signal Make sure the polarity of the connection is correct at each end of the cables Only conne
3. for your country s mains supply 300 1 500mA DC 1W in standby Replacement battery remote control 1 x CR2032 or 1 x CR2025 3V Dimensions W x H x D D with sockets 206 x 36 x 150 156 mm Weight 1 260g without power supply Technical specifications Pro Ject Speaker Box 5 Recommended amplifier power 10 150 watts Impedance 8ohms Sensitivity 1W 1m 86dB Dimensions W x H x D weight 160 x 255 x 210mm 4 2kg Technical specifications Pro Ject Control it Batteries Dimensions W x H x D Weight Service 2x AA 1 5 47 x 30 x 210mm 105g Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and or by transportation without the original packaging Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Copyright trademarks PRO JECT is a Registered Trademark of H Lichtenegger The information was correct at the time of going to This guide was produced by Audio Trade GmbH Copyright 2012 All rights reserved press The manufacturer reserves the right to make changes to the te
4. on from standby or to standby turns the iPod into standby To switch on from standby press any key except ON OFF Start Pause Stepping between tracks reverse and forward scanning 2 skips to the previous track skips to the next track restarts the current track in playback mode starts and pauses playback Press and hold the button for reverse scanning or the button to start forward scanning Repeat play EPEA fren starts repeat play for the current track Pressing the button again starts repeat play for all tracks To deactivate repeat play press REPEAT once more Shuffle play activates and deactivates shuffle play Navigating the menu m shows the menu Returns to the previous step in the menu Wy and move the curser up and down to highlight the requested option selects or deselects the highlighted option Shows the next step in the menu Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 5 Remote control Receiver Box S To switch on from standby or to standby ON OFF short press turns the unit on long press takes it back into standby Powered on a short press activates and deactivates mute me Volu and adjust the sound volume Selecting an input INPUT selects the inputs and tuner mode in turns Selecting the tuning mode Pressing min 3 seconds selects the tuning modes manual program search MANUAL automatic prog
5. 9 Saving a program in the memory list Tune to the frequency to be stored Press twice rapid succession CH will select the next memory position up the list selects the next memory position down the list The memory positions 1 8 can be selected directly by e pressing Press once again to store the program at that position Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 CD Box SE and CD Box DS only 1 6 o Tw press e turns the unit on or back into standby starts and pauses playback stops playback accesses specific track directly and start playback Higher track numbers for example to play track 19 press o VOL adjust the sound volume of the pre amplifier integrated amplifier receiver or Juke Box and Juke Box Esprit To step between tracks press e or Co Press and hold the button for fast reverse scanning activates fast forward scanning Pressing the button repeatedly selects the repeat modes in turns Selects random mode Pressing again takes the CD player back to standard playback Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Docking station Docking stations with volume control only No support of volume control with all digital units such as iPhone 5 press tur
6. The display shows the current track number the elapsed time of the current track and the play icon Pause II pauses playback The display shows the current track number the elapsed time of the current track and the pause icon To resume playback press I gt again Stop short press of the button B stops playback The display shows the total number of tracks on the disc the total duration of the disc and the stop icon Stepping between tracks Press the buttons previous track or next track The display shows the number of the tracks as you step the elapsed time of the current track and the step icon Scanning through the disc Press and hold the button M fast backward or PPI fast forward to scan through the disc The display shows the current track number the elapsed time of the current track and the scan icon Releasing M4 or PPI will take you back to playback Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Control it The six push buttons correspond to each unit Press the appropriate button to select the unit you want to control then press the required function buttons Blanked out buttons do not carry a function for the unit selected D p O ayer Receiver Receiver Box and Tuner Box J ocking Station co tream Box Pre amplifier integrated amplifier Juke Box and Juke Box Esprit Audio Trade GmbH Pro Ject M
7. ations with insufficient signal level while storing Front panel controls Receiver Box S 4 lt x o e o Receiver Box S To switch on from standby or to standby Receiver Box S The push button on the left hand side will toggle the receiver between its fully operational status and standby The blue LED above the stand by push button shows that the unit is switched on In standby the display will show STANDBY While switching off the unit saves the settings for input volume and mute to be set automatically after next power on Input selector After the unit is powered on the push button selects the inputs INT IN2 and the tuner mode in turn The display will show the volume level and the selected input TUNER INT or IN2 The optional input expander Pro Ject Switch Box S provides three more inputs For further details please see the user guide of the Pro Ject Switch Box S Volume 4 and gt adjust the volume 95 steps to the desired level The display will show the volume level set 954 indicates OOdB max Mute While the unit is powered activates and deactivates mute Dimming the display dh di e VOL VOL After pressing or on the remote control S ay set the brightness of the display Available settings DIM MIN DIM 1 DIM 4 and DIM MAX The ris will show the selected setting Audio Trade GmbH Pro Ject Micro Hifi System Set Revisio
8. chnical specification without prior notice as deemed necessary to uphold the ongoing process of technical development Windows XP Windows Vista Windows 77 Windows 8 are trademarks of the Microsoft group of companies iPod and Mac OS are trademarks of Apple Inc registered in the U S and other countries Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15
9. ct one loudspeaker with an impedance not less than 4 ohms per channel Connectors CD Box S S PDIF Power Left Right Co axial RoHS c Pro Ject Audio Systems Vienna Austria Out Out OO WV Make all connections whilst the CD player is disconnected from the power supply Connection to a external A D converter Connect the Co axial out socket to a coaxial digital input on the D A converter or AV processor Doing so allows you to use the signal in its digital for further digital processing Connectors Dock Box S Fi Left Power 18V USB RoHS Out Pro Ject Audio Systems Vienna Austria o WV Make all connections whilst the Dock Box is disconnected from the power supply Connecting to a computer iPod operating system p p g sy Connect the USB output of the Dock Box to a free USB socket on your computer and turn it on make sure it is powered on S When the Dock Box is connected to a computer all functions of the Dock Box are blocked Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 3 Connection to a TV set or a beamer Connect the S VIDEO socket to a s video input of your TV set or beamer Fitting and adjustment of the iPod cradle Use the knurled screw supplied to fix the cradle to the Dock Box chassis Do not fully tighten the screw yet Now place your iPod on the Dock Box contacts Move the c
10. d Dock Box S Fi Proceed as follows e Unlock and slide open the battery case cover Replace the battery Make sure the battery is the right way round e Close the battery case cover Battery type 1 x CR2032 3V or 1 x CR2025 3V Replacing batteries Control it Proceed as follows e Unlock and remove the battery case cover Replace the batteries Make sure the batteries are the right way round Refit the battery case cover nea Do not dispose the batteries as ordinary domestic refuse Please dispose your exhausted batteries at the appropriate collection sites usually located at supermarkets and drugstores Technical specifications Pro Ject Receiver Box S Power output 2 x 25W 30W at 8 ohms 4 ohms both channels driven Tuning range FM band 87 5 108MHz 50kHz steps Programmable presets 99 THD tuner 0 0596 Af 75kHz and f mod 1kHz Stereo separation 30dB Af 75kHz and f mod 1kHz Sensitivity 7dB uV mono 17dB yV stereo 75 ohms Frequency response 20Hz 20kHz 0 2dB Channel separation 404 at 20kHz Noise floor gt 100dB A weighted THD amplifier lt 0 05 at 1OW Gain 22dB Line level inputs pair RCA phono sockets 3 pole 3 5mm co axial jack Input impedance 20kohms Antenna input 1 x co axial DIN socket 75 ohms US model F socket Outboard power supply 20V 3A DC peak 7A DC suitable for your country s mains supply Power consumption DC 1W in standby Replacement battery
11. ect the program with the next memory position up the list lt selects the program with the next memory position down the list The program s memory position is shown to the right of MEMORY in the display Saving a program in the memory list The memory of the Pro Ject Receiver Box S can store up to 99 programs Tune to the frequency of the program to be stored Press twice in rapid succession The display will show STORE selects the next memory position up the list lt selects the next memory position down the list Press once on to store the program at that position The display shows STORED To be able to select a tuning modes manual program search automatic program search or i program selection from memory a antenna has to be connected Saving a program fo a particular memory position overwrites any program already stored at that position The memory retains its contents through a power off on cycle 8 Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Remote control CD Box S Q To switch on from standby or to standby ON OFF o e 9 turns the unit on or back into standby Volume control or adjust the sound volume of your Pro Ject Audio amplifier 173 T Q stops playback Play Pause Ado Selecting tracks d gt 10 9 ond accesses specific track directly and start playback 2o For example to play track 19 press To play track 29 pre
12. icro Hifi System Set Revision 2013 1 15 Pre amplifier integrated amplifier Juke Box and Juke Box Esprit press turns the unit on or back into standby VOL C and adjust the sound volume of the pre amplifier integrated amplifier receiver or Juke Box and Juke Box Esprit activates and deactivates mute CH e and select the inputs in turns Pre Box SE Pre Box DS and Stereo Box DS only Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Receiver and Tuner O Tha Sins Receiver only press short press turns the unit on long press takes it back into standby Powered on a short press activates and deactivates mute VOL and adjust the sound volume of the receiver pre amplifier integrated amplifier or Juke Box and Juke Box Esprit INPUT selects the inputs and tuner mode in turns Pressing min 3 seconds selects the tuning modes manual program search automatic program search and Program selection from memory Automatic program search CH starts the automatic frequency scan downwards starts the scan upwards Manual program search ce decreases Co increases the reception frequency in 50kHz steps Program selection from memory activate the memory function Access the presets 1 8 directly CH e and select memory function has to be activated the memory positions 9 9
13. modes in turns A and move the curser up and down to highlight the requested option A displays the play list in playback mode e displays the main menu Selects the highlighted option or modes in menus and submenus Press o or to step between folders OD or Q to step between next previous 5 entries of a folder Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Stream Box FOL lt lt gt il B Play view J FAV del turns the unit on or back into standby activates and deactivates mute cD starts and pauses playback stops playback Co skips to the next track picture or internet radio station e skips to the previous track picture or internet radio station navigate the cursor Calls up submenv Highlights and confirms a highlighted menu item Play view jumps one step back in a menu Play view calls up the root menu activates and deactivates shuffle play Pressing the button repeatedly selects the repeat modes in turns FAV add adds a track or an internet radio station to the favourite list o FAV del removes a track or a internet radio station from the favourite list keys for alphanumeric search and to enter the WLAN code Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Replacing batteries Receiver CD Box S an
14. n 2013 1 15 7 Setting the colour of the des display M3 M6 decreases m increases red m decreases increases green decreases increases blue The changes will be shown in the first line of the display After leaving the set op menu the changes will become valid for the complete display OK m loads the factory settings for brightness and colour To leave the set up menu press Display tuner mode 9 A Signal strength meter B Stereo reception F Mono reception C Fine tuning meter D Tuning mode The rotary selector toggles between the tuning modes E Tuned frequency Manual program search Press approx seconds repeatedly until the display shows MANUAL increases the reception frequency in 50kHz steps lt decreases the reception frequency in 50kHz steps The tuner is correctly adjusted for a stereo broadcast when A the largest number of bars are shown signal strength meter and B two loudspeaker symbols are shown F one loudspeaker symbol shows mono reception C the vertical bar is centred in the fine tuning display Automatic program search Press approx seconds repeatedly until the display shows AUTO gt starts the automatic frequency scan upwards will start it downwards The maximum signal strength will be adjusted automatically for each program found Program selection from memory Press approx seconds repeatedly until the display shows MEMORY will sel
15. ns the iPod iPhone into standby To switch on from standby press any key except ON OFF Dock Box Fi and Dock Box Vi only Turns the unit on or back into standby activates and deactivates mute VOL e and eo adjust the sound volume of the docking station cD starts and pauses playback Skips to the previous track e skips to the next track e restarts the current track in playback mode Press and hold the button for reverse scanning or the button Co to start forward scanning J starts repeat play for the current track Pressing the button again starts repeat play for all tracks To deactivate repeat play press once more J activates and deactivates shuffle play shows the menu Returns to the previous step in the menu A and Y move the curser up and down to highlight the requested option o selects or deselects the highlighted option Shows the next step in the menu Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Media Box press e turns the unit on or back into standby selects between card reader and USB starts and pauses playback Restarts playback from the same position after stopping Co skips to the next track e restarts the current track in playback mode Press and hold the button for reverse scanning or the button Co to start forward scanning Pressing the c button repeatedly selects the repeat
16. radle so that it supports the iPod and tighten the screw S Suitable for iPods with 30 pole connector only WV Use without the cradle breaks the 30 pole connector of the Dock Box and the socket of the iPod Before connecting the iPod any sort of cover has to be removed Mains power connection Receiver Box S Connect the low voltage plug from the power supply to the Power 20V socket before connecting the power supply to the mains CD Box S Connect the low voltage plug from the power supply to the Power 9V socket before connecting the power supply to the mains Dock Box S Fi Connect the low voltage plug from the power supply to the Power 18V 7 socket before connecting the power supply to the mains WV Never use any other power supply than the one supplied with the particular unit To switch on and off loading the battery Dock Box S Fi The push button on the front panel turns the Dock Box on and off The blue LED above the push button shows that the unit is switched on When the Dock Box is connected to the mains supply and switched the iPod will start recharging as soon as it is placed on the contacts Recharging will continue even if the iPod is on standby Recharging is not possible when the Dock Box is switched off Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Remote control Dock Box S Fi ON OFF o Blanked out buttons do not carry a function e To switch
17. ram search AUTO and program selection from memory MEMORY in turns Manual program search the display shows MANUAL MM decreases increases the reception frequency in 5OkHz steps Automatic program search the display shows AUTO CH CH starts the automatic frequency scan downwards starts the scan upwards Program selection from memory the display shows MEMORY M1 M8 M8 activate the memory function Pressing Ww Ww access the presets 1 8 directly i select memory function has to be activated the memory positions 9 99 Saving a program in the memory list 3 Tune to the frequency to be stored Press E twice in rapid succession The display will show STORE will select the next memory position up the list selects the next memory position down the list M1 M8 The memory positions 1 8 can be selected directly by pressing OK Press once again to store the program at that position The display shows STORED Saving a program fo a particular memory position overwrites any program already stored at that position The memory retains its contents through a power off on cycle Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Auto store function Long press starts m confirms the auto store function m clears the complete memory while storing d keeps stations with good signal strength in the memory and overwrites st
18. remote control 1 x CR2032 or 1 x 2025 3V Dimensions W x H x D D with sockets 103 x 36 x 104 122 mm Weight 670g without power supply Technical specifications Pro Ject Dock Box S Fi Frequency response 20Hz 20kHz Line level output 1 pair RCA phono sockets Output impedance 15 ohms Output voltage 1Vrms USB output 5 pole mini B jack USB signal digital serial data protocol USB 1 1 Operating systems Windows Windows VISTA Windows 7 Windows 8 Mac OS Video output S video socket Outboard power supply 18V 500mA DC suitable for your country s mains supply Power consumption 300mA DC max Power consumption is not constant It depends on the charging needs of the battery lt 1W in standby Replacement battery remote control 1 x CR2032 or 1 x CR2025 3V Dimensions W x H x D D with sockets 103 x 36 x 104 109 mm height plus height of iPod or iPhone Weight 585g without power supply Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 Technical specifications Pro Ject CD Box S Supports Frequency response Noise floor THD Line level output Output voltage Digital output D A converter Outboard power supply Power consumption CD CD R CD RW and Hybrid SACD 20Hz 20kHz 0 3dB 96dB 1V 0 01 1 pair RCA phono sockets Vrms 1 x co axial S PDIF Texas Instruments TLV320DAC23 24Bit 9 6kHz 8 times oversampling 9V 2 000mA DC suitable
19. ss P and 9 starts and pauses playback Stepping between tracks scanning through the disc Press or The display shows the number of the tracks as you step o E Press and hold the button for fast reverse scanning P activates fast forward scanning Repeat and random play 9 Pressing the button repeatedly selects the repeat modes in turns The display shows repeat play for the current track repeat play for all tracks Pressing 0 again takes the CD player back to standard playback Audio Trade GmbH Pro Ject Micro Hifi System Set Revision 2013 1 15 9 Front panel controls CD Box S g i BH e e CD Box S 1 0 lh To switch on from standby or to standby CD Box S short press of the push button on the left hand side switches the player to its fully operational status To return to standby press the button for more than four seconds The display shows STANDBY when the unit is in standby To switch to standby playback must be stopped Inserting and ejecting a disc Switch the unit on from standby Insert the disc into the slot with the label side facing upwards The slot loading mechanism will load the disc automatically The display shows the total number of tracks on the disc and the total duration of the disc short press of the button stops playback Pressing B again ejects the disc Play l gt starts playback of the first track
Download Pdf Manuals
Related Search