Quick Operation Guide_Z
Contents
1. For CE countries This scanner is in conformity with CE standards Please note that an approved CE marked power supply unit should be used in order to maintain CE conformance Laser Safety The laser scanner complies with safety standard IEC 60825 1for a Class laser produce It also complies with CDRH as applicable to a Class Ila laser product Avoid long term staring into direct laser light Radiant Energy The laser scanner uses one low power visible laser diodes operating at 650nm in an opto mechanical scanner resulting in less than 3 9uW radiated power as observed through a 7mm aperture and averaged over 10 seconds Do not attempt to remove the protective housing of the scanner as unprotected laser light with a peak output up to 0 8mW would be accessible inside Laser Light Viewing The scan window is the only aperture through which laser light may be observed from this product A failure of the scanner motor while the laser diode continues to emit a laser beam may cause emission levels to exceed those for safe operation The scanner has safeguards to prevent this occurrence If however a stationary laser beam is emitted the failing scanner should be disconnected from its power source immediately Adjustments Do not attempt any adjustments or alteration of this product Do not remove the protective housing of the scanner There are no user serviceable parts inside Caution Use of controls or adjustments or performance of proc2. J 45 connector to cradle cable box until you hear a clear and short click sound then connect the other end to the host 2 When using Keyboard wedge and USB interface for radio communication it is not necessary to have an external power adapter if host has sufficient power But these interfaces need external power adapter when charging batteries Note When external power adapter 9V is available the cradle will disregard the power supply from host 5V 3 If using RS 232 interface it is necessary to plug an external power adapter always Plug the power adapter into the DC Jack of cradle cable box Shown as Below 4 Once cradle powers up its LED lamp lights RED for one second then turns to flashes BLUE light The BLUE LED means the cradle is waiting to be connected If the scanner pairs with this cradle they are connected and BLUE LED light is always on Detach the Interface Cable There is a hole on cradle cable box and use a sharp pin to push down the hole while using another hand gently pull out the interface cable to release it slowly Pairing Scanner and Cradle Host This scanner supports three radio communication types Cradle Host SPP Serial Protocol Profile Slave SPP Serial Protocol Profile Master Refer to User s Manual for detailed description Paging the Scanner Paging the scanner often happens when you have two or more pairs of scanners and communication cradles and can not
3. Radio Notice This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with the instructions in this manual it may cause interference to radio communications The equipment has been tested and found to comply with the limits for a Class A computing device pursuant to EN55022 and 47 CFR Part 2 and Part 15 of the FCC rules These specifications are designed to provide reasonable protection against interference when operated in a commercial environment Radio and Television Interference Operation of this equipment in a residential area can cause interference to radio or television reception This can be determined by turning the equipment off and on The user is encouraged to try to correct the interference by one or more of the following measures Reorient the receiving antenna Relocate the device with respect to the receiver Move the device away from the receiver Plug the device into a different outlet so that the device and the receiver are on different branch circuits If necessary the user may consult the manufacturer and authorized dealer or experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 U S A Stock No 004000003454
4. edures other than those specified herein may result in hazardous laser light exposure Optical The use of optical instruments with this product will increase the eye hazard Optical instruments include binoculars magnifying glasses and microscopes but do not include normal eye glasses worn by the user 593 351 BTE 002 No warranty of any kind is made in regard to this material including but not limited to implied warranties of merchantability or fitness for a particular purpose We are not liable for any errors contained herein or incidental or consequential damages in connection with furnishing performance or use of this material No part of this document may be reproduced transmitted stored in a retrieval system transcribed or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without express written consent and authorization We reserve the right to make changes in product design without reservation and without notification The material in this guide is for information only and is subject to change without notice All trademarks mentioned herein registered or otherwise are the properties of their various respective owners Copyright 2009 All rights reserved Introduction This scanner is well featured with advanced wireless technology enabling working efficiency for simultaneous data transfer when scanning as well as work
5. find which scanner pairs with its cradle Press any key on cradle and it sends out a signal to its paired scanner this scanner beeps 3 beeps and lights BLUE LED 3 times But if the scanner is out of its receiving range then it won t react to the cradle Scanning There are two ways to scan with this device Handheld scanning Hands free scanning Handheld Scannin In the handheld scanning hand held the scanner and simply aim at a barcode label and push the scanner trigger to scan Avoid aim vertically to the barcode label as a total reflection might effect the scanning performance Hands free Scannin Put the scanner into the cradle for hands free scanning and move the barcode label approach the scanner scanning zone Maintenance This device provides reliable and efficient operation with a minimum of care Any visibly dirty or scratch on the scanner window will degrade reading performance therefore do not use abrasive wipes or tissues on the window When the scanner is not operating use a soft cloth or lens tissue and gently wipe the scanning window lens Do not spread liquid or submerge into liquid in any circumstance To know more about Pairing or Programming of this scanner please refer to User s Manual or contact your sales distributor for detail set up procedures
6. ing portability as not being constrained by short of cable length Working places as shipping industry Cargo warehouses superstores pharmacies and many more open space or large scale manufacturing sites are delighted to enjoy this move around freedom The cradle a dongle or any device with wireless technology can be the host of this scanner All scanned data are instantly transferred to the connected host in a 100 meter connection range in open space or 75 meter range in indoor environments the actual communication range may vary due to indoor placement As if out of connection range the embedded 32KB flash memory provides sufficient data space to store up to 500 sets of data Either scanning in the handheld or stand mode this scanner always offers a high accuracy and reliable scanning ability This scanner would be your trusted tool scanning partner Unpacking This scanner package contains 1 ea Wireless Single Line Laser Scanner 1 ea Charging Cradle or Cradle with Radio Communication 1 ea DC 9V Power Adapter 2 ea Ni MH AA Recharge Battery 1 ea Interface Cable only for the cradle with radio communication 1 ea Hand stripe 1 ea User s Manual If any contents are damaged or missing please contact your dealer immediately Please leave this user s manual within easy access of person using the scanner Wireless Handheld Laser CCD Scanner Scanner Outline Exit Window LED Lamp Buzzer Logo Scan Trigger Ba
7. is Smart Charge as battery life is well depended on the charging number of times so only charge the batteries when necessary by following the abovementioned procedures to prolong your battery life You may also set up auto charging as every time the scanner is placed into the cradle Follow and scan the appropriate barcode symbols to set up from programming section of this booklet Note For first charging always charge the batteries over 5 hours continuously to prolong your battery life After every full charge you may use the scanner for 8 hours continuously Recommended charging environment is temperature in 0C 35 32 F 95 F Connecting the Cradle There are two types of cradle to select for this scanner Charging Cradle Cradle Host Charging Cradle This cradle designs for battery charging only it does not support radio communication Simply connect the external DC 9V9W power adapter into it and place scanner into cradle to start charging Cradle Host The cradle host features with advanced wireless technology and designs to support radio communication to the scanner It the same has charging functionality Connection on Cradle Host The scanner pairs with the cradle when the scanner scans barcode data and passes to cradle via radio communication the cradle sends data to host by its interface cable Steps to connect the cradle to host as follows 1 Take the desirable interface cable and insert the R
8. ttery Cabinet Cradle Detecting Point Cradle Host Outline Scanner Detecting Point DC Jack Scanner Holder Cable Release Hole Cable Socket LED Lamp Function Triggers Installing and Charging Scanner Batteries Installing Batteries The rechargeable batteries are packed individually for shipping safety Please follow the steps below to install the batteries Caution Always use the rechargeable batteries provided by the manufacturer to avoid any non compatible danger or void the warranty 1 Loose the two screws enough to remove the battery cover It would not be necessary to remove the screws otherwise may result in losing them 2 Insert the batteries into the scanner one by one positive pole to positive pole negative pole to negative pole Charging Batteries For users with the charging cradle you can connect the charging cradle with power adapter and the scanner is now in charging For cradle host users you can connect the cradle with the power adapter first then place the scanner into the cradle in a 30 angle and press down to make it seat tight into the cradle a clear and short beep is heard when position correctly into the cradle Press Down Here Once the scanner is well situated in the cradle press down any one of the small buttons at the side of LED lamp to start charging Shown as Below The LED light in RED as in charge and light in BLUE when full charged We call th
Download Pdf Manuals
Related Search