USER`S MANUAL - Master Faucet
Contents
1. place themif worn Clean the surface ofthe airproofcavity thoroughly 2 Encase the fix sealing block take a smallball with RTVglued seal tothe brass axis cover push theairproof block into the airproof cavity It s enough to press bythe figure Cleanthe RTV on the surface of the seal thoroughly Put the O shape ring tothe brass axis cover on the fix sealing block the O shape ring mustbe stick close to the flange side Put some rubber lube e g P80 onthe O shapering for easy installation the gasoline type lube is forbidden Take a plasticlining and firmly put it to the flange bound of the brass sealing block Push the total seals to the crust s seal cavity of the motor 3 Clean the hub use water to clean the circumgyrating sealing block Evenly push the hub by the finger The screwdriver and otherhard tools are not al lowed to be used to prevent the sealing block from being damaged 4 According to thepicture push thecentrifugal oil ring 13 from the axis sh oulder tothe suitable position 5 Use 1 16 ball bearing and RTV sealing glue The sealing glue should be 360 degrees in touch withthe axis and the centrifugal oilring Keepthe sealing glue for 15 minutes 6 Install the crust 10 Screw down 4 inserting bolts 7 Screw the impellerdown to the axis The axis cover pushesthe certrifugal oil ring which is sealed tothe impeller by the RTV glue 8 Install O shape ring 9 to the cover 7 8 9 Put the cover 7 8 in positi2. transformer 2 Check the massage motor following the process whenthe motor cannot be started The waterdistri bution pump can not be turned completely The cold and hot water valve can not be inletturned completely The rubber ringin the valveis distorted or wornout The magnetic coreis worn out Replace it Replace it The crystal han dwheel is loose Press the screwson the topof the wheel and screw themclockwise The motor ofthe massage bath tub can not be started The voltage is abnormal or the power is off 2 The fuse is cut off the creepage switch is off 3 The pipe connecting the pneumatic switch to the motor falls off or blows 4 The pneumatic switch is broken 1 a Turn on the power b Insert the motor power plug into the special socket 2 Ask a technician to check wh ether there is something wro ng Ifnothing wrong replace the fuse orturn on the creep age overload protector 3 Get the plastic pipe connect ed or replace it 4 Ask an electrician to replace the pneumatic switch The drainer can notjump up or leaks 1 The screwis loosen oradjusted too low 2 The drainer sdrawing cable is broken 3 The cushionis uneven 1 Put off the drainer s stopper screw it or adjust the screw to suitable position 2 Replace the whole set 3 Dismantle the drainer then adjust itto be even reinstall it The water pump inst
3. USER S MANUAL ERE ACRYLIC MASSAGE BATHEUE CONTENTS Safety statement Installation and operation instruction Trouble shootig Maintenance Water pumpinstallation and operation instruction Please read carefully before using y SAFETY NOTICE The creepage overload protector should beinstalled in thepower supply The crustearth wire of the water pump should be well earthed It is forbidden to use the machine after having alcohol dring orhypnotic medicine The children should be accompanied by their parents when using the machine The parameters of the massage bathtub 1 The steam generator the rated 1 The applicable range of the working voltage is voltage C Ac220V Ac187V 256V O Ac110V Ac100V 115V 2 Frequency is O 50Hz O 60Hz Water pump power750W Transformer transformation9V power20W The pool bottom lamp voltage AC12V power20W The pump flux 20 stere hour Message bathtub water flow control principle illustration cold water hot water 1 e water fau 3 O ES m ASS e 2 KR l l shower i head H 22 4 5 NA hydro massage water regulating switch massage water pump o a pajzzou janno Jajem abesseu oJp y overflow outlet drawinage Illustration of the elect
4. allation w 1 nut 2 connection tube 11 2 tube O 3 connection tube 1 tube 4 amp 9 amp 15 O shape ring Y Ed 7 5 stainless steel bolt ye 6 stopper head s 7 cover the siphon SB type cD i ai siphon SCtype b peller 11 airproof groupware 2 7 12 pump body 13 centrifugal 14 motor Notice The above picture illustrates the name ofeach part If the fittings are needed please specify the name and number of the parts Also please specify the type andspecial number ofthe pump which is indicated on the label of the pump How toinstall and operate the water pump wW I Dismantle The repair of the water pump should be done by professional worker This instruction can help to repair and install the water pump Dismantle of the p ump should follow the instruction supplied by the producer 1 Demount 6 bolts 5 remove the cover 7 8 from the pump body 12 2 Demount the impeller anti clockwise Insertthe screwdriver intothe gap at the axis end ofthe motor to withstand the motor axis to remove the impeller 3 Loosen 4 bolts on the back ofthe motor to removethe pump body 4 Demountthe airproof groupware 11 5 Demountthe O shape ring 6 Push outthe fix sealing block from the back of crust 12 and checkthe ce ntrifugal oilring 13 II Reinstallation 1 Before reinstallation please checkthe centrifugal oil ring 13 theimpel ler 10 the airproof groupware 11 andthe cover O shape ring 9 Re
5. e of plated parts Please use flanneletto rub themgently Don t use rough clothto rub them Maintenance of the bathtub body When scratches appear 1500 sand paper can beused torub it Then polishthe tub by toothpaste andflannelet How to clean thenet Unscrew thenet and removeit Clean thenet tomake the water flow smoothly Do not use strongly corrosive chemicalliquid e g vitriol muriatic acidor lye torub the net 3 Installation First adjust the screws so thatthey reach theground Thenmake the bath tub level andfasten the screws Fixing the fourlegs of the steel stand tored uce the vibration of pump To preventthe pump or steel stand from transloc ation after longtime use rubberor some flexible material can be used as sh ockproof cushion Seal the gap betweenthe bathtub and the wall with glue Please notethat the drainage tube can notbe folded 4 Prepare to use Please make the waterlevel reach normal height usually 10cm higher than the nozzles to preventthe pump from working without water The direction of the nozzles can be adjusted to your mind 5 Special notice When installing thebathtub please makesure the metal parts are well e arthed Thecreepage overload protector should be installedin the power s upply wire 6 Note Before connecting the water pipe tothe water inletvalve of the bathtub pl ease eliminate theimpurities in the pipe such as rust Take care notto dama ge the valve core Trouble shooting
6. on Screwdown 6 bolts 5 10 Let the RTV tobe hard set for 1 hour before the motor can be started ot herwise the RTV glue will be thrown away Ifthe water pump is not usedin the CSA bath series the RTV glue need not to be used TIT Clue on We are not responsible for any faults resulted in the using of water pump and motor without following the operation instructions Please read the sta tement carefully before starting the pump 1 Donot use sealing glue with stone base tothe cannulation screw thread Please usethe RTV silicone sealant which is specially used in the plastic fluorin whorl strap When putting sealant be carefully notto drop intothe pump to preventfrom wrongly stickingto other parts 2 When the water level inthe pumpis lower than the nozzles itis not allow ed tostart the pump 3 Please check ifthe motor circuit diagram the power voltage and the power plug areup tothe standard 4 All the metal parts 1 5 m away from the bath shouldbe earthed withthe m otor The earth line should be copper wire not thinner than 1 5 square milli meters 5 The earthing lines inside the room should be copper wire not thinner than 4 0 square millimeters Notice All lines must be fixed according to standard by the pr ofessional electrician The motor must be earthed Please keep this explanation 4 The following basic preventive measures should be followed when installing and using the electric product 1 Read and follow the inst
7. ric principle of massage bathtub W power plug Q CI a water pump crust ok Qo a G2 M massage waterpump k pneumatic switch Bk transformer D bottom lamp G1 the earth wire of waterpump plug G2 the earth wire ofwater pump crust Fittings explanation y hotwater control valve H bottom lamp B water distribution control valve cool watercontrol valve 1 wateroutlet show head jr J water pump switch K hydro massage switch hydro massage water outlet nozzle drainage switch G water outlet net The operation instruction y 1 A B are cold and hot water control valves They can be turned on at the same time to adjust the water temperature Then B can be used to choose to use shower head D orwater outlet 1 2 Jis pneumatic switch Itturned on offthe water pump and bottom lamp at the sametime When the water pump is turned on hydro massage water comes out fromthe nozzles E Water flows back through thenet thus itb egins to circulate K is regulating switch controlling the power of the hydro massage water 3 F is the drainage switch which is used to drain the water 4 H isthe bottomlamp which makes it more convenientto use at night and beautify the enironment Maintenance YW 1 Temperature Themassage bathtubis suitable for waterbeow 80 C When usingit turn on the cold water before turning on the hot water 2 Maintenance Maintenanc
8. ruction 2 Warning any children without adult accompanying them can notuse this product 3 All installation of motor power lines shouldbe done bythe qualified electr Ician 4 The motorthat drives the pump can workunder high temperature Don tto uch the motor s crustto prevent from scald 5 Make surethat the water level shouldbe higher thanall the nozzles 6 This productcan only connectto the powerthat protected by GFCI the Gr ound Fault Current Interrupter which should be checked and installed by the qualified electrician and operated according to the instructions 7 Donot let anything drop into the gaps between the pump and motor 8 The water pump can notbe refitted added or deleted 9 The airswitch driver the push and press style air cell switch should bein stalled above the highest position of the bath when the pump is used 10 Oneconnection boltinside the connection box should be earthed tothe earthend ofthe powercircuit board using thesame line with the power wire which should notbe thinner than1 5 square millimeters 11 Warning to prevent from getting anelectric shock the earthing typeso cket protected by the GFClshould be used 12 Warning to prevent from getting an electric shock the worn out wires should be changed intime 13 Warning to preventfrom getting anelectric shock donot use the exte nd wire to connect the power The suitable socket position is required Please keep this instruction
9. y phenomenon reason how to solve 1 The steel stand under the bathtub is not hehe E dl on ti balanced The screws are not fastened OOP ane ac e cres 10 make the steel stand level Violent vibration 2 The fastening screw or the shockproof Pastene Seres and too much noise glue of the motor are incomplete or loose 3 The water level does not reach the normal height A There is something with wrong the motor 2 Normally there should be four and four shockproof cushions to fix the motor Fasten the loosen screws 3 The normal height of the water level should be 10cm higher than the metal parts ofthe nozzles The motor works normally but no water comes out from the nozzles or the water pressure is not high enough The not is partly jammed 2 The water level is too low 3 The hydro massage water regulating switch is turned off 4 Other reasons 14 Dismantle the net and clean it to make the water flow smooth 15 Increase the water level to normal height 10cm higher than all the nozzles 16 Turn on the hydro massage water regulating switch phenomenon The bottom lamp does not work reason 1 The water pump works _ b The connection line but the lamp breaks off doesn t broken 2 Neither the pump nor the lamp works a The bulb is broken c The transformer is how to solve 1 a Replace the bulb b Get the line connected c Replace the
Download Pdf Manuals
Related Search