NPort Z2150 User`s Manual
Contents
1. 2 Click Delete on the main toolbar lol x Z ZigBee Configuration Utility Connect Operation View Help Delete Refresh Config 4 The selected COM ports will be removed from the device list 15 x Z ZigBee Configuration Utility Connect Operation View Help bd kd Ee A H Add Delete Refresh Config Upgrade Configuring NPort Device 1 Once ZigBee Configuration Utility has found NPort device servers on the serial you can modify any unit s configuration Select the desired NPort in the main window and click Config on the main toolbar Z ZigBee Configuration Utility 3 5 NPort Z2150 User s Manual Installing and Configuring the Software 2 In the General tab you can change the device name It acts like a nickname for the target NPort device Config urations 3 In the Serial tab you can configure Baud Rate Parity Stop Bit and Interface Mode Serial Port l Vie ee Baud Rate 50 bps to 230400 bps Data Bits De n Stop Bits RS 232 RS 422 RS 485 Configurations mm i 3 6 NPort Z2150 User s Manual Installing and Configuring the Software 4 Inthe ZigBee tab you can configure ZigBee parameters The details of parameters are in the table below Device type The device can take three different device types Coordinator Router and End Device PAN ID The PAN identifier The range is from 0 to OxFFFD Channel The 2 4GHz channel The range is from 11 to 262. Topology Supports three kinds of topology Star Tree and Mesh Output power Supports 20 16 12 8 4 1 5 1 4 5 dBm Default value is 4 5 Device Type Advanced Description Settings Router End Local The identifier for each ZigBee node The range is from 0 to 99 Device node ID Default value is O for a Coordinator of NPort Z2150 or Z3150 Destination Assign the identifier of desired ZigBee node The range is from O0 to 99 Node ID Coordinator Mode Transmission mode Transparent or Addressable Transparent All data comes in via the serial port Coordinator will broadcast to the desired ZigBee node Addressable All data comes to the Coordinator via the serial port the Coordinator will send to the desired ZigBee node directly Start Byte The head of addressable mode command format on Coordinator Default value is 0x23 Configurations Ei General Serial ZigBee Security End Device e oun 0 OxFFFD Topology 3 7 NPort Z2150 User s Manual Installing and Configuring the Software Configurations 5 On the Security tab you can enable 128 bit AES encryption for Zigbee security After enabling security you must enter the 16 byte key with a combination of 32 HEX codes from 0 9 A F for AES encryption Finally click OK to enable the new configuration Configurations 6 The selected NPort will be restarted by ZigBee Configuration Utility with the new configuration Information E E
3. Power Requirements Input Voltage 12 to 48 VDC Power Consumption 45 mA 12 V Connector Power Jack Regulatory Approvals EMC CE EN55022 Class A EN55024 FCC Part 15 Subpart B Class A Safety UL UL60950 1 LVD EN60950 1 Reliability Automatic Reboot Trigger Built in WDT watchdog timer MTBF meantime between failures 2542774 hrs Warranty Warranty Period 5 years Details See www moxa com warranty Serial Port Pin Assignments heh Pin RS 232 RS 422 RS 485 4W RS 485 2W BEES oaf ww ZIL eD J TB LI O mw om 6789 5 3 DD o4 DTR GND sl es 2 RS si cs Cet 1 4 The following topics are covered in this chapter Overview Panel Layout LED Indicators DIP Switch Pull High Low Resistors for RS 422 485 Function Block Connecting the Hardware Connecting the Power O UD DU DD DUU OA Connecting to a Serial Device 2 Getting Started NPort Z2150 User s Manual Getting Started Overview This chapter presents the hardware features of the NPort Z2150 and explains how to connect the hardware Panel Layout o aa Df warn Reset Console Gd OnO 12 48 VDC 8 5 mm 0 73 in MOXA NPort Serial to ZigBee Converter 25 mm 0 98 in 43 mm 1 69 in 80 mm 3 15 in Ready Fault ZigBee Link 0 16 in serial TwRx 27mm 0 28 in RS 232 422 485 _ 52 mm 2 05 in 22mm 63 mm 2 48 in 0 87 in 75 mm 2 95 in LED Ind
4. Moxa Americas Toll free 1 888 669 2872 Tel 1 714 528 6777 Fax 1 714 528 6778 Moxa Europe Tel 49 89 3 70 03 99 0 Fax 49 89 3 70 03 99 99 www moxa com su ort Moxa China Shanghai office Toll free 800 820 5036 Tel 86 21 5258 9955 Fax 86 21 5258 5505 Moxa Asia Pacific Tel 886 2 8919 1230 Fax 886 2 8919 1231 Table of Contents Di Nd e end Le RE 1 1 Ee 1 2 PACE E E 1 2 Product gg EE 1 2 PFOGUCE SDOCIE CAUION EE 1 3 Seral PORE IP VARS e le an ne 1 4 2 Ce d Tat BR ln CCC EE 2 1 OS ER 2 2 Panel e EE 2 2 LS Dl olel ersiselgceeppeeeeere etree sec ere eee ce N rr rr er creer er er er er er errr er er ercer ere r eee 2 2 DIP SWIC Nieret eere e EEEE EEEE een EEE EEE ESE EA a AEAN AN OAEIAE OA N U EAE 2 3 P Ve te Re e Ee eg RS 422 48 EE 2 3 FP ULI NOE USI VO EE 2 4 COMMeG HIG UNC ar ae 2 4 Connecting The POW EEN 2 4 COMMECtING hee Seral DEVICE EE 2 5 3 Installing and Configuring the Software ek KKK EK KEE KEE KEE EK EE EK KEE KEE EK EE e 3 1 RE aden 3 2 ZIG BES C ONPG Ura CIO UCN CY E a a A 3 2 COPEL Ui Late NPO GW e 3 5 MADOU EXPO sae ce ee NONN cer reer rere rer errr Terre rrr re cre rerrre renee rre 3 9 Upgrading INPORC le UE 3 11 REL CS Eeer ele erdeelt 3 12 OD de EE 3 12 As ZIGBESS INUFOGUCUIOIN NEE A 1 DEVICE Ny DO EE A 1 NetWork TOD OlOOY EE A 1 The following topics are covered in this chapter o n n Overview Package Checklist Product Features Product Spec
5. Ver D on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup Finding NPort Z2150 Series on Serial You can use ZigBee Configuration Utility to look up or set configuration settings of any NPort on the serial All NPort units with SW1 ON in Console mode that are connected to the serial COM port of a PC can be found and configured 1 In ZigBee Configuration Utility click Add on the main toolbar Z ZigBee Configuration Utility Oj x Connect Operation View Help bald Eo BG Refresh Config Upgrade Se Device type Topology Mode PAN ID Localnode ID Channel F W version 3 3 NPort Z2150 User s Manual Installing and Configuring the Software 2 Select the COM port number which is connected to the NPort device and click Connect to find device In addition you can select multiple target COM ports Add Connection Port 3 The utility will search for NPort device servers 1 0 Build 11112915 3 4 NPort Z2150 User s Manual Installing and Configuring the Software Removing target COM port After configuring the NPort device you might want to remove the target COM port from the device list 1 Select the devices which you would like to remove You can select multiple ports lo x z ZigBee Configuration Utility Connect Operation View Help kd kd Ei O Refresh Config Upgrade 1 0 Build 11112915 3
6. allow full peer to peer communication ZigBee routers in mesh networks do not currently emit regular IEEE 802 15 4 2003 beacons This specification describes only intra PAN networks that is networks in which communications begin and terminate within the Same network NPort Z2150 User s Manual ZigBee Introduction NOTE In the star topology every device in the network can communicate only with the PAN coordinator A typical scenario in a star network formation is that an device programmed to be a PAN coordinator is activated and starts establishing its network The first thing this PAN coordinator does is select a unique PAN identifier that is not used by any other network in its radio sphere of influence the region around the device in which its radio can successfully communicate with other radios In other words it ensures that the PAN identifier is not used by any other nearby network Star Network Mesh Network Tree Network Simplest Best Reliability Large Scale Networks CH Coordinator Router ip End Device In a Mesh topology each device can communicate directly with any other device if the devices are placed close enough together to establish a successful communication link Any devices in a peer to peer network can play the role of the PAN coordinator One way to decide which device will be the PAN coordinator is to pick the first device that starts communicating as the PAN coordinator In a peer to peer network all the device
7. I 3 8 NPort Z2150 User s Manual Installing and Configuring the Software Import Export Exporting a Configuration 1 Once ZigBee Configuration Utility has found NPort device servers on the serial port you can export any unit s configuration Right click the desired NPort in the main window and select Export Z ZigBee Configuration Utility 2 Select the export directory and click OK to proceed Export File x Select Export Director Browse OK Cancel 3 A message will pop up confirming a successful export information ES Export configurations successfully 4 The configuration file will be saved in the txt format ER confie bet 3 9 NPort Z2150 User s Manual Installing and Configuring the Software Importing a Configuration 1 Once ZigBee Configuration Utility has found NPort device servers on the serial port you can import a config file to any unit Right click the desired NPort in the main window and select Import z ZigBee Configuration Utility l iol sl Connect Operation View Help kd kd ed oe G Refresh Config Upgrade TO Bua HEEN Import Select the file to import and click OK to proceed Import File x Select Fil E HPZ2150_Config i bt Browse 3 10 NPort Z2150 User s Manual Installing and Configuring the Software Upgrading NPort Firmware Once ZigBee Configuration Utility has found NPort device servers on the serial port you can
8. NPort Z2150 User s Manual Second Edition February 2015 www moxa com product MOXA 2015 Moxa Inc All rights reserved NPort Z2150 User s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice Trademarks 2015 Moxa Inc All rights reserved The MOXA logo is a registered trademark of Moxa Inc All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa Moxa provides this document as is without warranty of any kind either expressed or implied including but not limited to its particular purpose Moxa reserves the right to make improvements and or changes to this manual or to the products and or the programs described in this manual at any time Information provided in this manual is intended to be accurate and reliable However Moxa assumes no responsibility for its use or for any infringements on the rights of third parties that may result from its use This product might include unintentional technical or typographical errors Changes are periodically made to the information herein to correct such errors and these changes are incorporated into new editions of the publication Technical Support Contact Information
9. e A ATTENTION Before connecting the hardware follow these important wiring safety precautions Disconnect power source Do not install or wire this unit or any attached devices with the power connected Disconnect the power before installation by removing the power cord before installing and or wiring your unit Follow maximum current ratings Calculate the maximum possible current in each power wire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat causing serious damage to your equipment Use caution unit may get hot The unit will generate heat during operation and the casing may feel hot to the touch Take care when handling unit Be sure to leave adequate space for ventilation The following guidelines will help ensure trouble free signal communication with the NPort e Use separate paths to route wiring for power and devices to avoid interference Do not run signal or communication wiring and power wiring in the same wire conduit The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together e If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point e Keep input wiring and output wiring separate e Label all wiring to each device in the system for easier testing and troubleshooting Connecting
10. e MOXA ZigBee Configuration Utility Ver1 0 Setup Wizard This will install MOXA igBee Configuration Utility Ver1 0 on your computer tis recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup ie Setup MOXA ZigBee Configuration Utility Ver1 0 Select Destination Location Where should MOXA igBee Configuration Utility Ver1 0 be installed D Setup will install MOXA ZigBee Configuration Utility Ver1 0 into the following folder To continue click Next F you would like to select a different folder click Browse C Program Files Moxa 7igbee Utility Browse At least 0 7 MB of free disk space is required cack Nets Ges 3 2 NPort Z2150 User s Manual Installing and Configuring the Software 4 Verify the installation parameters and click Install to proceed ul Setup MOXA ZigBee Configuration Utility Vert 8 Ready to Install Setup is now ready to begin installing MOXA ZigBee Configuration Utility Ver on your computer Click Install to continue with the installation or click Back if you want to review or 5 The wizard will begin installing the files After the files have been installed click Finish to complete the installation w Setup MOXA ZigBee Configuration Utility Veri Completing the MOXA ZigBee Configuration Utility Ver1 0 Setup Wizard Setup has finished installing MOXA ZigBee Configuration Utility
11. icators There are three LEDs on NPort Z2150 The LED descriptions are as follows Ready Green On System power on Flashing 1 Device locating 2 Reset button pushed down Fault On System power on Flashing 1 If ZigBee LED is off it means Node ID conflict 2 If ZigBee LED is on it means Destination Node ID disappeared ZigBee Green On Initialized ZigBee PAN successfully Coordinator Blinking ZigBee Tx Rx Initialized ZigBee PAN fail Green On Joined ZigBee PAN successfully Router Blinking ZigBee Tx Rx Off Failed to join ZigBee PAN Green On Joined ZigBee PAN successfully End Device Blinking ZigBee Tx Rx Off Failed to join ZigBee PAN Parent node removed Serial data output to serial port Serial data input from serial port 2 2 NPort Z2150 User s Manual DIP Switch ON TT 1 2 Serial Connection Console Mode ON Operation Mode NOTE Reserved 2 for future usage Pull High Low Resistors for RS 422 485 You may need to set the pull high low resistors when termination resistors are used for certain RS 422 or RS 485 environments Getting Started ATTENTION effective communication distance Do not use the 1 KQ setting while in RS 232 mode Doing so will degrade the RS 232 signals and reduce the NPort Z2150 User s Manual Getting Started Function Block SMA Connector RS 232 422 485 Transceiver LED Indicator 12 48V Power jack Connecting the Hardwar
12. ifications Serial Port Pin Assignments 1 Introduction NPort Z2150 User s Manual Introduction Overview The NPort Z2150 provides a reliable wireless serial converter with support for serial to ZigBee communications The following architecture is the application overview for the NPort Z2150 The Z2150 can act as ZigBee Coordinator ZigBee Router or ZigBee End Device Any serial device can be connected by the Z2150 and exchange data via PAN Computer ZigBee e ZigBee Coordinator Router ZigBee End Device VW Coordinator Vi Router W End Device Package Checklist Before installing the NPort Z2150 verify that the package contains the following items Standard Accessories NPort Z2150 2 4 GHz omni directional antenna Documentation and software CD Warranty card Quick Installation Guide Optional Accessories DK 35A DIN rail mounting kit 35 mm NOTE Please notify your sales representative if any of the above items are missing or damaged Product Features Instant connection of any serial device to a ZigBee network RS 232 422 485 ports supporting baudrates up to 230 4 kbps Friendly configuration with serial console Secure data access with AES Supports End Device Router and Coordinator roles l 2 NPort Z2150 User s Manual Introduction Product Specifications ZigBee Interface RF Standard 802 15 4 Frequency Band 2 4 GHz Interface Immunity DSSS RF Data Rate 250 Kbps Rx se
13. n monitor the status of devices Moreover the monitor items is defined to what you selected in the Option window Options 1 In ZigBee Configuration Utility click View gt Options on the menu bar Z ZigBee Configuration Utility 2 Select or de select items Use the single arrowhead buttons to move highlighted items from one box to the other Use the double arrowhead buttons to move all items in one box to the other options x Device name Device type Topology Mode FAN ID Local node ID Channel Parent addr Short addr Output power AA version Security Default OF Cancel 3 12 A ZigBee Introduction The ZigBee standard is a set of low data rate short range wireless networking communication protocols ZigBee supports a maximum data rate of 250 kb s and works in the 868 MHz 915 MH and 2 4 GHz frequency bands ZigBee is particularly common in battery powered and energy limited applications where those qualities are valued In many ZigBee applications the ZigBee wireless devices spend most of their time in power saving or sleep mode so they can go years between battery replacements Home patient monitoring is a good example of a typical ZigBee application The heart rate and blood pressure sensors worn at home by patients are often connected to a worn ZigBee device that periodically transmit sensor data to a local server such as a home PC for initial analysis The local server can then use an Internet co
14. nnection to forward this medical data on to medical professionals for more detailed analysis Device Type The ZigBee standard uses slightly different terminology ZigBee coordinator An IEEE 802 15 4 2003 PAN coordinator ZigBee end device An IEEE 802 15 4 2003 RFD or FFD participating in a ZigBee network which is neither the ZigBee coordinator nor a ZigBee router ZigBee router An IEEE 802 15 4 2003 FFD participating in a ZigBee network which is not the ZigBee coordinator but may act as an IEEE 802 15 4 2003 coordinator within its personal operating space that is capable of routing messages between devices and supporting associations Network Topology The ZigBee network layer NWK supports star tree and mesh topologies In a star topology the network is controlled by one single device called the ZigBee coordinator The ZigBee coordinator is responsible for initiating and maintaining the devices on the network All other devices known as end devices directly communicate with the ZigBee coordinator In mesh and tree topologies the ZigBee coordinator is responsible for starting the network and for choosing certain key network parameters but the network may be extended through the use of ZigBee routers In tree networks routers move data and control messages through the network using a hierarchical routing strategy Tree networks may employ beacon oriented communication as described in the IEEE 802 15 4 2003 specification Mesh networks
15. nsitivity 96 dBm Tx Power 4 5 dBm Max Transmission Distance Up to 100m in open areas Antenna 2dB PAN ID 0x0000 OxFFFD Node ID 00 99 RF Channel 11 26 16 channels Device Type Coordinator Router End Device Network Topology Star Mesh Tree Security 128 bit AES encryption algorithms Serial Interface Number of Port 1 Serial Standards RS 232 422 485 Connector DB9 male RS 485 Data Direction Control ADDC Automatic Data Direction Control Serial Communication Parameters Data Bits 8 Stop Bits 1 2 Parity None Even Odd Flow Control RTS CTS XON XOFF Baudrate 50 bps to 230 4Kbps Serial Signals RS 232 TxD RxD RTS CTS DTR DSR DCD GND RS 422 TxD TxD RxD RxD GND RS 485 4w TxD TxD RxD RxD GND RS 485 2w Data Data GND Software ZigBee Configuration Utility Hardware DIP Switch on the box Console Operation Mode Reserved DIP Switch inside the box SW1 2 Pull high low resistor SW3 Termination for RS 422 485 Reset Button Reset to default Physical Characteristics Weight 340g Dimension Without ears 52 x 80 x 22 mm 2 05 x 3 15 x 0 87 in With ears 75 x 80 x 22 mm 2 95 x 3 15 x 0 87 in 1 3 NPort Z2150 User s Manual Introduction Environmental Limits Operating Temperature Standard Models O to 55 C 32 to 131 F Wide Temp Models 40 to 75 C 40 to 167 F Operating Humidity 5 to 95 RH Storage Temperature 40 to 85 C 40 to 185 F
16. s that participate in relaying the messages are devices because devices are not capable of relaying the messages However an device can be part of the network and communicate only with one particular device a coordinator or a router in the network ZigBee supports a tree topology In this case a ZigBee coordinator PAN coordinator establishes the initial network ZigBee routers form the branches and relay the messages ZigBee end devices act as leaves of the tree and do not participate in message routing ZigBee routers can grow the network beyond the initial network established by the ZigBee coordinator Please refer to the book ZigBee Wireless Networks and Transceivers A 2
17. the Power m Connect the VDC power line 12 to 48 V to the NPort s power jack If power is properly connected the Ready LED will initially glow red When the system is ready the Ready LED will turn green 2 4 NPort Z2150 User s Manual Getting Started Connecting to a Serial Device Use a serial cable to connect your serial device to the serial port on the NPort 2 5 3 Installing and Configuring the Software The following topics are covered in this chapter Overview ZigBee Configuration Utility Configuring NPort Device Import Export Upgrading NPort Firmware Refresh OUUQAQQA A Options NPort Z2150 User s Manual Installing and Configuring the Software Overview This chapter describes how to install and use the ZigBee Configuration Utility These items are located on the Documentation amp Software CD that is provided with the NPort Z2150 ZigBee Configuration Utility is a utility for the management of NPort device servers over serial ports You may also use ZigBee Configuration Utility to upgrade the firmware ZigBee Configuration Utility Installing ZigBee Configuration Utility 1 The main installation window will open when you insert the Document amp Software CD Click INSTALL UTILITY to proceed Once the program starts running click Yes to proceed 2 The installation wizard will open Click Next to proceed ie Setup MOXA ZigBee Configuration Utility Ver1 0 Welcome to th
18. upgrade any unit s firmware 1 Select the desired NPort in the main window and click Upgrade firmware CH ZigBee Configuration Utility Connect Operation View Help e Refresh Config Upgrade Device type Topology PANID Channel 26 1 device s selected Select the new firmware file and click OK to proceed To obtain the latest firmware for the NPort Z2150 visit www moxa com Upgrade Firmware X Select File Browse OK Cancel The utility will begin upgrading the firmware for the selected unit Do not disconnect or power off the unit while the firmware is being upgraded Waiting for device complete Total ports 4 14336 239645 E Firmware upgrading 2 When the displayed status is OK E E Upgrade firmware successfully ATTENTION ZigBee Configuration Utility supports upgrading the firmware of multiple units simultaneously 3 11 NPort Z2150 User s Manual Installing and Configuring the Software Refresh 1 Once ZigBee Configuration Utility has found NPort device servers on the serial port you can monitor all unit statuses manually Right click the desired NPort in the main window and select Refresh Z ZigBee Configuration Utility II x Connect Operation View Help TE Refresh Config Upgrade 1 0 Build 11112915 Refresh 2 After clicking the Refresh button the desired NPort device will update its information This way you ca
Download Pdf Manuals
Related Search