NK2(DW) 아트지(150x150)-110302
Contents
1. DW BASE INSTALLATIONS Philips 8 32 x 0 75 Surface Mount MOUNTING ON ELECTRICAL JUNCTION BOX NOTE Screws required for electrical junction boxes not supplied These screws are readily available at well stocked electrical supply store DW CONNECTING TO MONITORS DC 12V AC 24V Down 2nd Video Output Monitor 300 0 m Power Connection 12V DC 24V AC Dual Voltage Auto Polarity Detection and Protection m All cameras are equipped with a 2nd video output on the camera Main Board ADJUSTING THE VARI FOCAL DC AUTO IRIS LENS Follow the instructions provided below to make any lens adjustments DWC D4363D DWC D4363TIR DWC D4367WD C gt 2 DWC D4367WTIR DWC D4365T pe D4382TIR Zoom Tele amp Wide Focus Far Near Loosen the Zoom amp Focus screws Using the screw move it RIGHT or LEFT to the desired position Once the desired adjustments have been made tighten the screw to lock in place Adjust the Field of View by2. EXPOSURE DAY amp NIGHT BRIGHTNESS WB MODE D amp N MODE L SHUTTER R Y GAIN L C SUP BLC HME B Y GAIN LA SUP AGC STARLIGHT NIGHT UP FUNCTION MOTION PRIVACY MIRROR MOTION PRIVACY SHARPNESS GAMMA FREEZE NEGATIVE gt D ZOOM 3D DNR DRC SYNC SETUP EXIT SYNC TITLE EDIT EXIT T CONTROL SAVE amp EXIT 1 88485 Control L FACTORY RESET LANGUAGE MONITOR OSD COLOR OMNI LENS DEFECT DW 19 EXPOSURE BRIGHTNESS 0 100 SHUTTER 1 60 FLK 1 250 10000 SENS UP x2 x256 BLC HME OFF BLC HME AGC HIGH MIDDLE LOW OFF AGC Auto Gain Control STARLIGHT AUTO x2 x256 OFF NIGHT UP NORMAL HIGH EXIT JUMP EXIT SAVE amp EXIT FACTORY SET COLOR WB MODE AWC AWT PUSH LOCK MANUAL INDOOR OUTDOOR R Y GAIN 0 100 B Y GAIN 0 100 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 4 DAY amp NIGHT Day amp Night Mode AUTO READ TIME 3 63 S LEVEL 0 100 E LEVEL 0 100 COLOR B amp W Switching from COLOR to BW Ifthe number is higher the camera wil only switch during a super low light condition B amp W COLOR Switching from BW to COLOR This number should be always lower than COLOR to BW Read Time time interval to switch from COLOR to BW COLOR B amp W Mode B
3. FUNCTION MIRROR OFF MIRROR V FLIP ROTATE SHARPNESS 0 31 GAMMA 0 05 1 00 FREEZE OFF ON NEGATIVE OFF ON D ZOOM OFF ON x1 0 x32 PTZ 3D DNR ON 0 100 OFF 3D Digital Noise Reduction DRC OFF INDOOR OUTDOOR Dynamic Range Compressor EXIT JUMP EXIT SAVE amp EXIT FACTORY SET MOTION OMNI Plus Camera Only MOTION OFF ON AREA SELECT AREA 1 4 AREA SET PO a SIZE A 055 0 MOTIO E OFF ON MOTION VIEW OFF ON RETURN EXIT JUMP EXIT SAVE amp EXIT FACTORY SET t PRIVACY PRIVACY OFF ON 7 AREA SE LECT 1 8 AREA SET POSITION SIZE COLOR 0 15 RETUR EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 15 SYNC SYNC INTERNAL LINE EXIT JUMP EXIT SAVE amp EXIT FACTORY SET SETUP TITLE EDIT OFF ON PC CONTROL CAM ID ID DISPLAY OFF ON BAUDRATE 2400 4800 9600 RS485 Control The protocol is fixed pelco D LANGUAGE ENG KOR JPN CHN1 CHN2 RUS FRAN SPAN ITAL MONITOR CRT LCD Select LCD only if the camera is directly connected to the LCD monitor OSD COLOR 0 15 OMNI LENS OFF OMNI Plus Camera Only ON _t ALARM READ TIME ALARM ZOOM STAND BY RETURN DEFECT WHITE DEFECT CANCEL MODE EXIT JUMP EXIT SAVE amp EXIT FACTORY SET EXIT EXIT SAVE amp EXIT FACTORY RESET 16 DW SPECIFICATIONS MODEL DWC D4363D General Spec NTSC PAL CCD Type 1
4. C_SUP Color Suppression Color will be reduced at low illumination if the C SUP Level is higher 0 100 not available when 3D DNR is A_SUP Aperture Suppression Edge sharpness will be reduced at low illumination if A_SUP Level is higher 0 100 not available when 3D DNR is EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 22 DW FUNCTION MIRROR OFF MIRROR V FLIP ROTATE SHARPNESS 0 49 0 45 1 00 USER 2 OFF OFF ON 3D DNR OFF LOW MIDDLE HIGH 3D DNR 3D Digital Noise Reduction D ZOOM OFF ON x1 0 x3 0 Digital PTZ SLC OFF SLC Side Light Compensation HME OFF ON HME Highlight Masking Exposure DIS OFF ON DIS Digital Image Stabilizer EXIT JUMP EXIT SAVE amp EXIT FACTORY SET EMOTION MOTION OFF ON SET WINDOW ALL SET Set the Entire Screen ALL CLEAR Clear the Entire Screen SENSITIVITY 1 120 SHOW INDICATOR OFF ICON TRACE DELAY OUT 1 15 Motion Alarm Zoom In Delay EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 33 t PRIVACY MASK 1 OFF ON MASK 2 OFF ON MASK OFF ON 1 MASK 4 OFF ON 1 MASK 5 OFF ON 1 MASK 6 OFF ON EXIT JUMP EXIT SAVE amp EXIT FACTORY SET SYNC SYNC MODE INTERNAL AUTO V_PHASE 0 199 EXIT JUMP EXIT SAVE amp EXIT
5. R Y GAIN C SUP BLC B Y GAIN A SUP AGC MAX DR STARLIGHT FUNCTION MOTION PRIVACY r MIRROR MOTION r MASK 1 SHARPNESS MASK 2 GAMMA MASK 3 FREEZE MASK 4 NEGATIVE __MASK 5 3D DNR MASK 6 D ZOOM SLC HME DIS SYNC SETUP EXIT SYNC r CAMERA ID m EXIT TZ TITLE SAVE amp EXIT BET DPC FACTORY SET MONITOR LANGUAGE BAUDRATE OMNI LENS DW 31 EXPOSURE BRIGHTNESS 0 99 SHUTTER 1 60 1 100 FLC 1 250 100000 SENS UP x2 x256 BLC OFF BLC Back Light Compensation AGC HIGH MIDDLE LOW OFF AGC AUTO GAIN CONTROL MAX_DR OFF ON 0 20 Electronic Wide Dynamic Range STARLIGHT AUTO x2 x256 OFF x32 is recommended for low light application EXIT JUMP EXIT SAVE amp EXIT FACTORY RESET COLOR WB MODE AWC ATW MANUAL AWC is recommended R Y GAIN 0 255 B Y GAIN 0 255 EXIT JUMP EXIT SAVE amp EXIT FACTORY RESET 4DAY amp NIGHT Day amp Night Mode AUTO COLOR BW EX CONT COLOR BW Switching from COLOR to BW Ifthe number is higher the camera will only switch during a super low light condition BW COLOR Switching from BW to COLOR This number should be always lower than COLOR to BW Read Time time interval to switch from COLOR to BW COLOR B amp W BURST OFF ON When the burst is OFF the picture will have less noise
6. SAVE amp EXIT FACTORY RESET COLOR WB MODE AWC ATW MANUAL AWC is recommended R Y GAIN 0 255 B Y GAIN 0 255 EXIT JUMP EXIT SAVE amp EXIT FACTORY RESET 4DAY amp NIGHT Day amp Night Mode AUTO COLOR BW EX CONT COLOR BW Switching from COLOR to BW Ifthe number is higher the camera will only switch during a super low light condition BW COLOR Switching from BW to COLOR This number should be always lower than COLOR to BW Read Time time interval to switch from COLOR to BW COLOR B amp W BURST OFF ON When the burst is OFF the picture will have less noise C_SUP Color Suppression Color will be reduced at low illumination if the C SUP Level is higher 0 100 not available when 3D DNR is A_SUP Aperture Suppression Edge sharpness will be reduced at low illumination if A_SUP Level is higher 0 100 not available when 3D DNR is EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 26 DW FUNCTION MIRROR OFF MIRROR V FLIP ROTATE SHARPNESS 0 49 0 45 1 00 USER FREEZE OFF ON NEGATIVE OFF ON 3D DNR OFF LOW MIDDLE HIGH 3D DNR 3D Digital Noise Reduction D ZOOM OFF ON x1 0 x3 0 Digital PTZ SLC OFF ON SLC Side Light Compensation HME OFF ON HME Highlight Masking Exposure DIS OFF ON DIS Digital Image Stabilizer EXIT JUMP EXIT SAVE amp EXIT FACTORY SET MOT
7. x256 BLC OFF ON BLC Back Light Compensation AGC HIGH MIDDLE LOW OFF AGC AUTO GAIN CONTROL MAX_DR OFF ON 0 20 Electronic Wide Dynamic Range STARLIGHT AUTO x2 x256 OFF x32 is recommended for low light application EXIT JUMP EXIT SAVE amp EXIT FACTORY RESET COLOR WB MODE AWC ATW MANUAL AWC is recommended R Y GAIN 0 255 B Y GAIN 0 255 EXIT JUMP EXIT SAVE amp EXIT FACTORY RESET DAY amp NIGHT Day amp Night Mode AUTO COLOR BW COLOR BW Switching from COLOR to BW ffthe number is higher the camera wil only switch during a super low light condition BW COLOR Switching from BW to COLOR This number should be always lower than COLOR to BW Read Time time interval to switch from COLOR to BW COLOR B amp W BURST OFF ON When the burst is OFF the picture will have less noise C_SUP Color Suppression Color will be reduced at low illumination if the C_SUP Level is higher 0 100 not available when 3D DNR is A_SUP Aperture Suppression Edge sharpness will be reduced at low illumination if A_SUP Level is higher 0 100 not available when 3D DNR is EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 38 DW FUNCTION MIRROR OFF MIRROR V FLIP ROTATE SHARPNESS 0 49 0 45 1 00 USER FREEZE OFF ON NEGATIVE OFF ON 3D DNR OFF LOW MIDDLE H
8. 3 410K Pixels Color 1 3 470K Pixels Color Total number of pixels 811 H X 508 V 795 H X 596 V Minimum Illumination 0 14Lux F1 2 30IRE COLOR OLux LED ON Resolution 560 TV Lines COLOR 580 TV Lines BW Electric Spec Voltage DC 12 V 11 0 V 20 0 V AC 24 V 20 0 V 30 0 V Power Consumption DC 12V 2 3W AC 24V 2 5W COMMON General Spec NTSC PAL Shutter speed 1 60s 1 100 000s 1 50s 1 100 000s SIN Ratio 52dB or More AGC OFF Gamma 0 45 Sync System Internal Line Lock Mechanical Spec Operation Temperature 10 C 50 14 F 131 F Storage Temperature 20 C 70 Operation Humidity Under 90 Non condensing 17 FEATURES D4363TIR m 1 3 Sony Super HAD CCD 560 TV Lines m 3 3 12mm Varifocal Auto Iris Lens 100ft Range IR with Intelligent Camera Sync m TDN True Day and Night TDN5 m Star Light Super Low Light Technology m DRC Dynamic Range Compressor m 3D DNR 3D Digital Noise Reduction HME Highlight Masking Exposure m AGC BLC AWB m 32X Digital Zoom Negative Imaging m UTP RS485 Built In m Programmable Privacy Zone 8 amp Motion Detection 4 Easy Icon Driven OSD Menu with Built In Joystick Auto Sensing 12VDC or 24VAC with Line Lock Secondary Video BNC Output 18 MODULE OSD MENU
9. FACTORY SET SETUP CAMERA ID 0 254 RS485 ID TITLE OFF ON DPC OFF AUTO DPC Dead Pixel Cancellation MONITOR CRT LCD Select LCD only if the camera is directly connected to LCD monitor LANGUAGE English Chinese BAUDRATE 2400 4800 9600 14400 19200 38400 The protocol is Pelco D Fixed and cannot be changed Hardcoded onto the DSP OMNI LENS OFF 1 10 OMNI Plus Camera Only EXIT JUMP EXIT SAVE amp EXIT FACTORY SET EXIT EXIT Exit the menu SAVE amp EXIT Exit the menu and save the setting FACTORY SET Reset the menu setting to factory default 34 DW SPECIFICATIONS MODEL DWC D4367WTIR General Spec NTSC PAL CCD Type 1 3 410K Pixels Color 1 3 470K Pixels Color Total number of pixels 811 H X 508 V 795 H X 596 V Minimum Illumination 0 14Lux F1 2 30IRE COLOR OLux LED ON Resolution 580 TV Lines COLOR 600 TV Lines BW Spec Voltage DC 12 V 11 0 V 20 0 V AC 24 V 20 0 V 30 0 V Power Consumption LED OFF DC12V 2 1W AC24V 2 2W LED ON DC12V 4 5W AC24V 4 6W COMMON General Spec NTSC PAL Shutter speed 1 60s 1 100 000s 1 50s 1 100 000s S N Ratio 50dB or More AGC OFF Gamma 0 45 Sync System Internal Line Lock Mechanical Spec Operation Temperature 10 C 50C 14 F 131 F Storage Temperature 20 C 70 C Operation Humidity Und
10. SPAN ITAL MONITOR CRT LCD Select LCD only if the camera is directly connected to the LCD monitor OSD COLOR 0 15 OMNI LENS OFF OMNI Plus Camera Only ON ALARM READ TIME ALARM ZOOM STAND BY RETURN DEFECT WHITE DEFECT CANCEL MODE EXIT JUMP EXIT SAVE amp EXIT FACTORY SET EXIT EXIT SAVE amp EXIT FACTORY RESET 22 DW SPECIFICATIONS MODEL DWC D4363TIR General Spec NTSC PAL CCD Type 1 3 410K Pixels Color 1 3 470K Pixels Color Total number of pixels 811 H X 508 V 795 H X 596 V Minimum Illumination 0 14Lux F1 2 30IRE COLOR OLux LED ON Resolution 560 TV Lines COLOR 580 TV Lines BW Electric Spec Voltage DC 12 V 11 0 V 20 0 V AC 24 V 20 0 V 30 0 V Power Consumption LED OFF DC12V 2 3W AC24V 2 5W LED ON DC12V 4 8W AC24V 4 9W COMMON General Spec NTSC PAL Shutter speed 1 60s 1 100 000s 1 50s 1 100 000s S N Ratio 52dB or More AGC OFF Gamma 0 45 Sync System Internal Line Lock Mechanical Spec Operation Temperature 10 C 50C 14 F 131 F Storage Temperature 20 C 70 C Operation Humidity Under 90 Non condensing 23 DSNOwnO FEATURES D4367WD 1 3 Sony Super HAD CCD 580 TV Lines m 3 3 12mm Varifocal Auto Iris Lens Electronic Day and Night Star Light Super Low Light Technology EWDR Electron
11. TITLE EDIT EXIT T CONTROL SAVE amp EXIT 1 88485 Control L FACTORY RESET LANGUAGE MONITOR OSD COLOR OMNI LENS DEFECT DW 13 EXPOSURE BRIGHTNESS 0 100 SHUTTER 1 60 FLK 1 250 10000 SENS UP x2 x256 BLC HME OFF BLC HME AGC HIGH MIDDLE LOW OFF AGC Auto Gain Control STARLIGHT AUTO x2 x256 OFF NIGHT UP NORMAL HIGH EXIT JUMP EXIT SAVE amp EXIT FACTORY SET COLOR WB MODE AWC AWT PUSH LOCK MANUAL INDOOR OUTDOOR R Y GAIN 0 100 B Y GAIN 0 100 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 4 DAY amp NIGHT Day amp Night Mode AUTO READ TIME 3 63 S LEVEL 0 100 E LEVEL 0 100 COLOR B amp W Switching from COLOR to BW Ifthe number is higher the camera wil only switch during a super low light condition B amp W COLOR Switching from BW to COLOR This number should be always lower than COLOR to BW Read Time time interval to switch from COLOR to BW COLOR B amp W Mode BURST OFF ON There is less noise when the BURST is OFF SMART IR OFF ON C_SUP Color Suppression Color will be reduced at low illumination if the C SUP Level is set higher 0 63 A_SUP Aperture Suppression The sharpness of the edges will be reduced at low illumination if A SUP level is set higher 0 15 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 14 DW
12. ALARM OFF ALARM ON READ TIME 5 15 ALARM ZOOM 4 214 STAND BY 0 214 RETURN FLUORESCENT OFF CRR Manual Lens Color Rolling Flickerless Mode CRR2 DC Lens Color Rolling Mode DIGITAL VIDEO DIGITAL OUT OFF ON OUTPUT FIELD ORDER NORMAL REVERSE FRAME RPT OFF 2 FREEZE RETURN EXIT JUMP EXIT SAVE amp EXIT FACTORY SET EXIT EXIT SAVE amp EXIT FACTORY RESET 47 SPECIFICATIONS 48 MODEL DWC D4365T General Spec NTSC PAL CCD Type 1 3 420K Pixels Color Total number of pixels 768 H X 548 V Minimum Illumination 0 22Lux F1 2 30IRE COLOR OLux LED ON Resolution H 690 TV Lines Effective Electric Spec Voltage DC 12 V 11 0 V 20 0 V AC 24 V 20 0 V 30 0 V Power Consumption DC12V 3 1W AC24V 3 2W COMMON General Spec NTSC PAL Shutter speed 1 25 1 30 720 sec S N Ratio 53dB or More AGC OFF Gamma 0 45 Sync System Internal Line Lock Mechanical Spec Operation Temperature 10 C 50 14 F 131 F Storage Temperature 20C 70 Operation Humidity Under 90 Non condensing DW WARRANTY INFORMATION Digital Watchdog referred to as the Warrantor warrants the Digital Watchdog Camera against defects in materials or workmanship as follows LABOR For the initial two 2 years and one 1 year on IR LED from the original purchase date if the camera
13. CATIONS MODEL DWC D4382TIR General Spec NTSC PAL CCD Type 1 3 410K Pixels Color 1 3 470K Pixels Color Total number of pixels 811 H X 508 V 795 H X 596 V Minimum Illumination 0 14Lux F1 2 30IRE COLOR OLux LED ON Resolution 580 TV Lines COLOR 600 TV Lines BW Spec Voltage DC 12 V 11 0 V 20 0 V AC 24 V 20 0 V 30 0 V Power Consumption LED OFF DC12V 2 1W AC24V 2 2W LED ON DC12V 4 5W AC24V 4 6W COMMON General Spec NTSC PAL Shutter speed 1 60s 1 100 000s 1 50s 1 100 000s S N Ratio 50dB or More AGC OFF Gamma 0 45 Sync System Internal Line Lock Mechanical Spec Operation Temperature 10 C 50C 14 F 131 F Storage Temperature 20 C 70 C Operation Humidity Under 90 Non condensing 41 REMOTE CONTROL m REMOTE CONTROL Instructions 1 Set the camera ID in OSD menu The default setting is 001 Menu Access and Control NOTE If the camera ID is modified the new camera ID must be set and the power must be turned ON and OFF Then the yoo Function Control camera is able to recognize the new ID A 2 Press the KEY and the camera turns into the standby image I The LED flickers for 20 seconds 3 Input ID number of CAMERA to Remote Controller ID number I After you input the ID number LED light is turned on and the remote controller is
14. DA esos Everything s Digital SNAP IT Indoor Dome Camera DWC D4363D DWC D4363TIR DWC D4367WD DWC D4367WTIR DWC D4382TIR DWC D4365T ABOUT MANUAL Before installing and using the camera please read this manual carefully Be sure to keep it handy for future reference 03022011 PRECAUTIONS m Do not open or modify m Do not open the case except during maintenence and installation for it may be dangerous and can cause damages m Do not put objects into the unit Keep metal objects and flammable substances from entering the camera It can cause fire short circuits or other damages Be careful when handling the unit To prevent damages do not drop the camera or subject it to shock or vibration Do not install near electric or magnetic fields Protect from humidity and dust Protect from high temperature Be careful when installing near the ceiling of kitchen or a boiler room as the temperature may rise to high levels m Cleaning To remove dirt from the case moisten a soft cloth with a soft detergent solution and wipe m Mounting Surface The material of the mounting surface must be strong enough to support the camera COMPLIANCE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to Provide reasonable protection against harmful interference when the equipment is operated in a residential environment This equipmen
15. IGH 3D DNR 3D Digital Noise Reduction D ZOOM OFF ON x1 0 x3 0 Digital PTZ SLC OFF ON SLC Side Light Compensation HME OFF HME Highlight Masking Exposure DIS OFF ON DIS Digital Image Stabilizer EXIT JUMP EXIT SAVE amp EXIT FACTORY SET EMOTION MOTION OFF ON SET WINDOW ALL SET Set the Entire Screen ALL CLEAR Clear the Entire Screen SENSITIVITY 1 120 SHOW INDICATOR OFF ICON TRACE DELAY OUT 1 15 Motion Alarm Zoom In Delay EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 39 PRIVACY MASK 1 OFF ON MASK 2 OFF ON MASK 3 OFF ON MASK 4 OFF ON MASK 5 OFF ON MASK 6 OFF ON 1 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET SYNC SYNC MODE INTERNAL AUTO V_PHASE 0 199 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET SETUP CAMERA ID 0 254 RS485 ID TITLE OFF ON DPC OFF AUTO DPC Dead Pixel Cancellation MONITOR CRT LCD Select LCD only if the camera is directly connected to LCD monitor LANGUAGE English Chinese BAUDRATE 2400 4800 9600 14400 19200 38400 The protocol is Pelco D Fixed and cannot be changed Hardcoded onto the DSP OMNI LENS OFF 1 10 OMNI Plus Camera Only EXIT JUMP EXIT SAVE amp EXIT FACTORY SET EXIT EXIT Exit the menu SAVE amp EXIT Exit the menu and save the setting FACTORY SET Reset the menu setting to factory default 40 DW SPECIFI
16. ION MOTION OFF ON SET WINDOW ALL SET Set the Entire Screen ALL CLEAR Clear the Entire Screen SENSITIVITY 1 120 SHOW INDICATOR OFF ICON TRACE DELAY OUT 1 15 Motion Alarm Zoom In Delay EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 27 PRIVACY MASK 1 OFF ON MASK 2 OFF ON MASK OFF ON MASK 4 OFF ON MASK 5 OFF ON 1 MASK 6 OFF ON EXIT JUMP EXIT SAVE amp EXIT FACTORY SET SYNC SYNC MODE INTERNAL AUTO V_PHASE 0 199 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET SETUP CAMERA ID 0 254 RS485 ID TITLE OFF DPC OFF AUTO DPC Dead Pixel Cancellation MONITOR CRT LCD Select LCD only if the camera is directly connected to LCD monitor LANGUAGE English Chinese BAUDRATE 2400 4800 9600 14400 19200 38400 The protocol is Pelco D Fixed and cannot be changed Hardcoded onto the DSP OMNI LENS OFF 1 10 OMNI Plus Camera Only EXIT JUMP EXIT SAVE amp EXIT FACTORY SET EXIT EXIT Exit the menu SAVE amp EXIT Exit the menu and save the setting FACTORY SET Reset the menu setting to factory default 28 DW SPECIFICATIONS MODEL DWC D4367WD General Spec NTSC PAL CCD Type 1 3 410K Pixels Color 1 3 470K Pixels Color Total number of pixels 811 H X 508 V 795 H X 596 V Minimum Illumination 0 14Lux F1 2 30IRE COLOR OLux LED ON Resolut
17. MIRROR OFF MIRROR V FLIP ROTATE SHARPNESS 8 8 GAMMA 25 0 25 100 1 0 3D DNR MOVIE INFO D ZOOM ZOOM 1 x1 0 12 x8 PAN 100 100 TILT 100 100 Digital Zoom Pan using the camera mini joystick EXIT JUMP EXIT SAVE amp EXIT FACTORY SET MOTION MOTION OFF ON ACTIVITY THR 0 255 SET MOTION ZONES 1 ZONE 1 2 ZONE 1 ZONE 1 4 ZONE ADJUST ZONE 1 MOVE MAKES WIDE MAKES NARROW ADJUST ZONE 2 MOVE MAKES WIDE MAKES NARROW ADJUST ZONE 3 MOVE MAKES WIDE MAKES NARROW ADJUST ZONE 4 MOVE MAKES WIDE MAKES NARROW RETURN EXIT JUMP EXIT SAVE amp EXIT FACTORY SET PRIVACY PRIVACY OFF ON _t AREA 1 OFF ON MOVE MAKES WIDE MAKES NARROW AREA 2 OFF ON MOVE MAKES WIDE MAKES NARROW AREA 3 OFF ON MOVE MAKES WIDE MAKES NARROW AREA 4 OFF ON MOVE MAKES WIDE MAKES NARROW AREA 5 OFF ON MOVE MAKES WIDE MAKES NARROW AREA 6 OFF ON MOVE MAKES WIDE MAKES NARROW RETURN EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 46 DW SYNC SYNC INT1 SYNC to 59 94Hz INT2 SYNC to 60 01Hz LL LL LIMIT V PHASE RETURN EXIT JUMP EXIT SAVE amp EXIT FACTORY SET SETUP PC CONTROL CAM ID 1 255 ID DISPLAY OFF ON PROTOCOL PELCO D BAUDRATE 2400 4800 9600 19200 RETURN TITLE OFF ON f TIILE D POSITION UP LEFT UP CENTER UP RIGHT DOWN LEFT DOWN CENTER DOWN RIGHT LANGUAGE ENGLISH MONITOR CRT LCD OMNI LENS OFF ON _t
18. URST OFF ON There is less noise when the BURST is OFF SMART IR OFF ON C_SUP Color Suppression Color will be reduced at low illumination if the C SUP Level is set higher 0 63 A_SUP Aperture Suppression The sharpness of the edges will be reduced at low illumination if A SUP level is set higher 0 15 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 20 DW FUNCTION MIRROR OFF MIRROR V FLIP ROTATE SHARPNESS 0 31 0 05 1 00 FREEZE OFF ON NEGATIVE OFF D ZOOM OFF ON x1 0 x32 PTZ 3D DNR ON 0 100 OFF 3D Digital Noise Reduction DRC OFF INDOOR OUTDOOR Dynamic Range Compressor EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 8 MOTION OMNI Plus Camera Only MOTION OFF ON AREA SELECT AREA Ta AREA SET POSITION SIZE SENSITIVITY 0 40 MOTION TRACE OFF ON MOTION VIEW OFF ON RETURN EXIT JUMP EXIT SAVE amp EXIT FACTORY SET t PRIVACY PRIVACY OFF ON 1 AREA SELECT L178 AREA SET POSITION SIZE GOLOR 0 15 RETUR EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 21 5 SYNC INTERNAL LINE EXIT JUMP EXIT SAVE amp EXIT FACTORY SET SETUP TITLE EDIT OFF ON PC CONTROL CAM ID ID DISPLAY OFF ON BAUDRATE 2400 4800 9600 RS485 Control The protocol is fixed pelco D LANGUAGE ENG KOR JPN CHN1 CHN2 RUS FRAN
19. Video BNC Output 43 MODULE OSD MENU 44 EXPOSURE COLOR DAY amp NIGHT r BRIGHTNESS r WB MODE D amp N MODE AE PREFERENCE COLOR GAIN r BLC r WDR AGC STARLIGHT METER ZONE FUNCTION MOTION PRIVACY MIRROR MOTION PRIVACY SHARPNESS GAMMA r 3D DNR D ZOOM SYNC SETUP EXIT SYNC r PC CONTROL r EXIT TITLE SAVE amp EXIT LANGUAGE FACTORY RESET MONITOR OMNI LENS FLUORESCENT DIGITAL VIDEO OUT DW EXPOSURE BRIGHTNESS 48 60 AE PREFERENCE OUTDOOR INDOOR BLC OFF BLC PERCENTILE 10 50 WDR LOW NORMAL MEDIUM HIGH CUSTOM AGC LOW MEDIUM HIGH CUSTOM STARLIGHT 2 x64 OFF METER ZONE ADJUST ZONE 1 ADJUST ZONE 2 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET COLOR WB MODE AWC ATVV 2 000K 11 000K PUSH LOCK MANUAL KELVIN 2 000K 11 000K R B RED 20 20 BLUE 20 20 COLOR GAIN 8 8 EXIT JUMP EXIT SAVE amp EXIT FACTORY SET DAY amp NIGHT D amp N MODE AUTO AUTO EXT COLOR B amp W AUTO Mode READ TIME 0 255 S LEVEL 0 60 E LEVEL 0 60 BW AGC 0 60 AUTO EXT Mode Option IR LED Mode COLOR Mode B amp W Mode BW BURST OFF ON EXIT JUMP EXIT SAVE amp EXIT FACTORY SET 45 FUNCTION
20. er 90 Non condensing 35 IN co FEATURES D4382TIR m 1 3 Sony Super HAD CCD 580 TV Lines OMNI Focus 2 9 8 5mm 3X Motorized Zoom Auto Iris m 70ft Range IR with Intelligent Camera Sync TDN True Day and Night TDN5 Star Light Super Low Light Technology EWDR Electronic Wide Dynamic Range m 3D DNR 3D Digital Noise Reduction HME Highlight Masking Exposure m AGC BLC AWB m Negative Imaging m 3X Digital Zoom m UTP RS485 Built In m Programmable Privacy Zone 6 amp Motion Detection m Easy Icon Driven OSD Menu with Built In Joystick m Auto Sensing 12VDC or 24VAC with Line Lock m Secondary Video BNC Output 36 MODULE OSD MENU EXPOSURE DAY amp NIGHT BRIGHTNESS r WB MODE r D amp N MODE H SHUTTER R Y GAIN C SUP BLC B Y GAIN A SUP AGC MAX DR STARLIGHT FUNCTION MOTION PRIVACY r MIRROR MOTION r MASK 1 SHARPNESS MASK 2 GAMMA MASK 3 FREEZE MASK 4 NEGATIVE __MASK 5 3D DNR MASK 6 D ZOOM SLC HME DIS SYNC SETUP EXIT SYNC r CAMERA ID m EXIT T TITLE SAVE amp EXIT BET DPC FACTORY SET MONITOR LANGUAGE BAUDRATE OMNI LENS DW 37 EXPOSURE BRIGHTNESS 0 99 SHUTTER 1 60 1 100 FLC 1 250 100000 SENS UP x2
21. ic Wide Dynamic Range 3D DNR 3D Digital Noise Reduction HME Highlight Masking Exposure SLC Side Light Compensation m AGC BLC AWB m Negative Imaging m 3X Digital Zoom Mirror Image Control m UTP RS485 Built In m Programmable Privacy Zone 6 amp Motion Detection m Easy Icon Driven OSD Menu with Built In Joystick m Auto Sensing 12VDC or 24VAC with Line Lock m Secondary Video BNC Output 24 MODULE OSD MENU EXPOSURE DAY amp NIGHT m BRIGHTNESS r WB MODE m D amp N MODE SHUTTER R Y GAIN C SUP BLC B Y GAIN A SUP AGC MAX DR STARLIGHT FUNCTION MOTION PRIVACY r MIRROR MOTION r MASK 1 SHARPNESS MASK 2 GAMMA MASK 3 FREEZE MASK 4 NEGATIVE __MASK 5 3D DNR MASK 6 D ZOOM SLC HME DIS SYNC SETUP EXIT SYNC r CAMERA ID m EXIT T TITLE SAVE amp EXIT BET DPC FACTORY SET MONITOR LANGUAGE BAUDRATE OMNI LENS DW 25 EXPOSURE BRIGHTNESS 0 99 SHUTTER 1 60 1 100 FLC 1 250 100000 SENS UP x2 x256 BLC OFF ON BLC Back Light Compensation AGC HIGH MIDDLE LOW OFF AGC AUTO GAIN CONTROL MAX_DR OFF ON 0 20 Electronic Wide Dynamic Range STARLIGHT AUTO x2 256 OFF x32 is recommended for low light application EXIT JUMP EXIT
22. ion 580 TV Lines COLOR 600 TV Lines BW Spec Voltage DC 12 V 11 0 V 20 0 V AC 24 V 20 0 V 30 0 V Power Consumption DC12V 2 1W AC24V 2 2W COMMON General Spec NTSC PAL Shutter speed 1 60s 1 100 000s 1 50s 1 100 000s SIN Ratio 50dB or More AGC OFF Gamma 0 45 Sync System Internal Line Lock Mechanical Spec Operation Temperature 10 C 50 14 F 131 F Storage Temperature 20 C 70 Operation Humidity Under 90 Non condensing 29 A ASNOwWARO FEATURES D4367WTIR 1 3 Sony Super HAD CCD 580 TV Lines m 3 3 12mm Varifocal Auto Iris Lens 100ft Range IR with Intelligent Camera Sync m TDN True Day and Night TDN5 Star Light Super Low Light Technology EWDR Electronic Wide Dynamic Range m 3D DNR 3D Digital Noise Reduction HME Highlight Masking Exposure SLC Side Light Compensation m AGC BLC AWB m Negative Imaging 3X Digital Zoom m UTP RS485 Built In m Programmable Privacy Zone 6 amp Motion Detection m Easy Icon Driven OSD Menu with Built In Joystick m Auto Sensing 12VDC or 24VAC with Line Lock m Secondary Video BNC Output 30 MODULE OSD MENU EXPOSURE DAY amp NIGHT m BRIGHTNESS r WB MODE m D amp N MODE SHUTTER
23. is determined to be defective the Warrantor will repair or replace the unit with a new or refurbished product at its option at no charge PARTS In addition the Warrantor will supply replacement parts for the initial two 2 years and one 1 year on IR LED To obtain warranty or out of warranty service please contact a Technical Support Representative at 1 866 446 3595 Monday through Friday from 8 30AM to 8 00PM Eastern Standard Time A purchase receipt or other proof of the original purchase date is required before warranty service is rendered This warranty only covers failures due to defects in materials and workmanship which arise during normal use This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident misuse abuse neglect mishandling misapplication alteration modification faulty installation set up adjustments improper antenna inadequate signal pickup maladjustment of consumer controls improper operation power line surge improper voltage supply lightning damage rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God 49 LIMITS AND EXCLUSIONS There are no express warranties except as listed above The Warrantor will not be liable for incidental or consequential damages including without limitation or damage to rec
24. moving the screw towards the RIGHT Tele to zoom in or towards the LEFT Wide to zoom out Adjust the Focus the same way as described above after the desired zoom position is estabilished 10 DW ADJUSTING 3 AXIS GIMBAL The Gimbal mechanism yields maximum rotation and placement ad show below Tilting 90 Q Tilting 82 11 9 FEATURES D4363D m 1 3 Sony Super HAD CCD 560 TV Lines m 3 3 12mm Varifocal Auto Iris Lens Electronic Day and Night Star Light Super Low Light Technology 3D DNR 3D Digital Noise Reduction DRC Dynamic Range Compressor HME Highlight Masking Exposure m AGC BLC AWB m 32X Digital Zoom Negative Imaging m UTP RS485 Built In m Programmable Privacy Zone 8 amp Motion Detection 4 m Easy Icon Driven OSD Menu with Built In Joystick m Auto Sensing 12VDC or 24VAC with Line Lock m Secondary Video BNC Output 12 MODULE OSD MENU EXPOSURE DAY amp NIGHT BRIGHTNESS WB MODE D amp N MODE L SHUTTER R Y GAIN L C SUP BLC HME B Y GAIN LA SUP AGC STARLIGHT NIGHT UP FUNCTION MOTION PRIVACY MIRROR MOTION PRIVACY SHARPNESS GAMMA FREEZE NEGATIVE gt D ZOOM 3D DNR DRC SYNC SETUP EXIT SYNC
25. ording media resulting from the use of these products or arising out of any breach of the warranty All express and implied warranties including the warranties of merchantability and fitness for particular purpose are limited to the applicable warranty period set forth above Some States do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the exclusions or limitations listed above may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state If the problem is not handled to your satisfaction then write to the Address listed on the next page Service calls which do not involve defective materials or workmanship as determined by the Warrantor in its sole discretion are not covered Costs of such service calls are the responsibility of the purchaser 50 DAZ IGITAL WATCHDOG Everything s Digital 5436 W Crenshaw St Tampa FL 33634 Tel 866 446 3595 813 888 9555 Fax 813 888 9262 www Digital Watchdog com technicalsupport dwcc tv Technical Support Hours Monday Friday 8 30am to 8 00pm Eastern Time
26. ready to set the camera NOTE The ID number must be 3 digit ID Buttons 4 ZOOM IN ZOOM IN Key These are for controlling lens zoom and selecting the zooming area of alarm function 5 Select the desired area where you wish to observe the movement of objects And then select the zooming range by pressing 7 wide key 6 Please save alarm generating zooming range by 8 tele key If ALARM generating zoom range is smaller than ALARM standby range ALARM Zoom range setting will not be saved Remote Control Picture 7 If select 9 ON OFF key product operates automatically from tele to wide 1 time and then the alarm function starts 8 Please press 9 key to cancel the alarm function or to reselect the alarm zooming area Key Button Motion Alarm ON amp OFF NOTE Press KEY ID Default is 001 for ID 1 Press ENT to access the Menu Note The camera ID is a 3 digit number 42 DW FEATURES D4365T 1 3 Pixim Seawolf CMOS Sensor m 690 Horizontal TV Lines 3 3 12mm Varifocal Auto Iris Lens TDN True Day and Night TDN5 Powerful Wide Dynamic Range 3D DNR 3D Digital Noise Reduction m Ultra Low Light Sensitivity Smear Canceling Circuit Low Power Consumption m UTP RS485 Built In m Programmable Privacy Zone 6 amp Motion Detection 4 m Easy Driven OSD Menu with Built In Joystick m Auto Sensing 12VDC or 24VAC with Line Lock m Secondary
27. t generates uses and radiates radio frequency energy and if it is not installed and used in accordance with the instruction manual it may cause harmful interference to radio communications WARNING Changes or modifications are not expressly approved by the manufacture 2 DW TROUBLESHOOTING Before sending your camera for repair check the following or contact our technical specialist No VIDEO Check the coaxial cable and make sure it is connected securely Check the lens iris adjustment at the menu setup of the camera Check the power supply and make sure the camera has the proper voltage and current Out of Focus VIDEO Check the clear dome cover and the lens for dirt or fingerprints Use a soft cloth and gently clean Check the lens manual focal and zoom adjustment Field test monitor is recommended Zz 0O 2 2 amp 0 O PART amp DESCRIPTIONS Lens Power Input Connctor 12VDC 24VAC Dual Voltage UTP RS 485 Video Output Connector BNC Bubble Upper Case Camera Control Board 2nd Video Connector Mounting Screws NOTE These assembly screws located on the dome cover and not with mounting hardware DW INSTALLATION Included with DW Indoor Dome Camera 1 User Manual 2 Mounting Template 3 Two 2 Screw and Two 2 Dry Wall Anchors 4 2nd Video Jack 5 IR Remote Controller DIMENSIONS IN MILLIMETERS Surface Mount Indoor 108
Download Pdf Manuals
Related Search