User manual - Jaktbutiken.se
Contents
1. a sufficient intensity to contrast against the target c Remove the windage and elevation adjustment caps NOTE Each click of the adjustment screw corresponds to a 10 mm movement of the point of impact at 80 meters 3 mm at 25 meters 13 mm at 100 meters and 25 mm at 200 meters or 1 4 at 50 yds at 100 yds and 1 at 200 yds d Insert adjustment tool coin screwdriver knife or cartridge casing in adjust ment screw slot and turn as follows To move the point of impact to the right turn windage adjustment screw counterclockwise clockwise if screw located on left side e To move the point of impact to the left turn windage adjustment screw clockwise counterclockwise if screw located on left side To move the point of impact up turn elevation adjustment screw counter clockwise To move the point of impact down turn elevation adjustment screw clock wise e Confirm zeroing by firing at least three shots at a zeroing target Check impact points on zeroing target to confirm accuracy and repeat above procedure if re quired f After initial firing ensure that the mount and sight are secure g Turn rotary switch to OFF position counterclockwise h Close front and rear lens covers CHAPTER III Operation under extreme conditions a Extreme heat moist or dry No special procedures required b Extreme cold Extreme cold might shorten battery life Keep spare batteries in your inner pockets to keep them2. CompM2 and ML2 models CHAPTER II OPERATION UNDER NORMAL CONDITIONS 2 1 Assembly and preparation for use WARNING Insure the weapon is unloaded and the safety selector is in the safe position before attempting to install remove or perform maintenance on the sight 2 1 1 Installing Battery a Remove battery cap by turning it counterclockwise b Insert battery with positive end toward cap Caution while replacing battery not necessary when the sight is unused Before installing battery cap inspect that the O ring is present and not damaged Failure to do so could result in water leakage into the battery compartment c Install battery cap by turning clockwise until snug Hand tighten only Using tools could damage equipment d Verify that red dot is present by turning the rotary switch clockwise 2 1 2 Installing Ring and Sight on the weapon Aimpoint s sights are designed for installation on most types of weapons For mounting certain models come with one or two rings for other models use stan dard rings available on the market If your weapon does not have or support an appropriate base s please consult your dealer gunsmith or other qualified source a When using two separate bases on the weapon ensure that the bases are parallel and aligned b Assemble the ring s on the appropriate weapon base a Weaver or Picatinny base When using 2 rings make sure that the distance between the rings is appropriate to
3. User s Manual for Aimpoint Comp and 7000 series CHAPTER I 1 1 Presentation Aimpoints Reflex Sights are rugged precision electronic optical red dot sights developed for civilian military and law enforcement applications Aimpoint sights are designed for the two eyes open method of sighting which greatly enhances situational awareness and target acquisition speed Thanks to the parallax free design the dot follows the movement of the user s eye while remaining fixed on the target eliminating any need for centering Further the sight allows for unlimited eye relief The CompM2 is compatible with 1 2 and 3 generation night vision devices while the other sights are optimized for applications which do not require night vision compatibility Aimpoint has now introduced the CETechnology a radical advancement in red dot sighting performance with over 30 times longer battery life than the previous XD sights 1 2 Specification 1 2 1 All models Material housing Extruded high strength aluminum anodized Material lens covers Thermoplastic elastomer black non glare Optical magnification 1X for all models except for 2X Eye relief Unlimited no centering required Optical coating Anti Reflex coating all surfaces Multi layer coating for reflection Band Pass coating for NVD compatibility CompM2 Dot size 4 MOA 2 MOA for 2X 7 MOA in CompC SM only Battery One 3 Volt Lithium battery type 2L76 or DL1 3N Batter
4. ameter Switch dot brightness 10 pos 1 Off 9 daylight of which 1 Extra Bright Max temperature range 30 C to 60 C 20 F to 140 F Water resistance Waterproof to 2 m 7 ft water depth 1 2 4 Model CompM2 CompML2 CompM2 2X and CompML2 2X Length incl lens covers CompM2 ML2 130 mm 5 1 CompM2 2X ML2 2X 165 mm 6 5 Width height CompM2 ML2 55 mm 2 2 CompM2 2X ML2 2X 60 mm 2 4 Weight incl lens covers CompM2 ML2 200 gram 7 1 oz CompM2 2X ML2 2X 290 gram 10 2 oz 3 Surface finish Hard Anodized Graphite Grey matte Mounting One wide ring 30 mm diam or Aimpoint QR Ring Switch dot brightness CompM2 M2 2X 10 positions 4 NVD 6 daylight of which 1 Extra Bright CompML2 ML2 2X 10 positions 1 Off 9 daylight of which 1 Extra Bright Max temperature range 45 C to 70 C 50 F to 160 F Water resistance Submersible to 25 m 80 ft water depth Tests performed have shown that sights will stand over 100 meters 330 ft of water depth 1 3 Location and description of major components and functions See fig 1 and 2 1 Battery Lid 7 Rubber Strap 2 Battery for CompM2 and ML2 models DL1 3N or similar 8 Eye Protection 3 Cover for adjustment screw 9 Lens Cover rear 4 Adjustment Screw for CompM2 and ML2 models windage elevation 10 Lens Cover front 5 Rotary Switch for CompM2 and ML2 models 6 Rubber Strap 11 Lens Cover for 2X for 7000 models and CompC for
5. er severe weather conditions please refer to chapter III c Keep lens covers closed whenever the sight is not in use d Warehouse storage Remove battery and allow lens surfaces to dry completely if wet before closing the lens covers e To clean lenses refer to CAUTION in chapter III
6. the sight Note make sure that you have space between the bottom front part of the sight and the top of the base weapon c For Comp models Assemble the sight to the weapon by using Aimpoint s wide 30 mm ring or QR mount Ifother standard 30 mm rings are used make sure that the ring s covers a length of minimum 25 mm or 1 two standard rings could pos sibly be used c For 7000 models Assemble the sight to the weapon with any standard 30 mm rings d Ensure that the sight is correctly positioned for right or left hand shooting see fig 3 and 4 e When using lens covers ensure that they are correctly positioned and can be opened f Finally make sure that all screws are firmly tightened around the sight g Complete the zeroing 2 2 1 2 2 OPERATING PROCEDURES 2 2 1 Zeroing Aimpoints sights are delivered in a centered position Normally this means that only small adjustments are necessary providing that the base s are properly alig ned CAUTION Do not continue to adjust windage and elevation mechanisms if you encounter resistance The elevation adjustment screw is located on top of the sight while the windage screw is located on the right or left side depending on how the sight has been mounted on the weapon Aimpoint sights can be installed to support either right hand fig 3 or left hand fig 4 shooters a Open front and rear lens covers b Turn the rotary switch clockwise until the red dot has
7. warm c Salt air No special procedures required d Sea spray water mud and snow Ensure that battery cap and two adjustment screw caps are tight before exposing the sight to sea spray mud snow or before immersing the sight in water Hand tighten only Keep lens covers closed when sight is not being used Clean lenses with lens paper cloth and wipe the sight dry as soon as possible after exposure to water sea spray mud or snow e Dust storms and sand storms Keep lens caps closed when sight is not being used f High altitudes No special procedures required CAUTION The lenses shall never be cleaned with fingers but with lens paper cloth If no lens paper cloth available To clear away debris sand grass etc blow away the dirt To clean lenses mist up the lenses and dry them with a clean and soft piece of cloth CHAPTER IV Trouble shooting procedures 4 1 Red dot does not appear Discharged battery Replace battery Battery installed incorrectly Remove and reinstall battery with toward cap Battery is not making good contact Clean contact surfaces and reinstall battery Defective rotary switch Notify dealer armourer 7 4 2 Impossible to zero Adjustment screw is at its limit Check alignment of mount to barrel Impact point is moving Check mount stability CHAPTER V MAINTENANCE a This reflex sight does not require any particular maintenance while used under normal conditions b Und
8. y life hours 1000 10 000 h typically 10 years at CompM2 NVD position 100 1000 h for CompC SM XD Diode Adjustment Range 2 m at 100 meters in windage and elevation 1 click 10 mm at 80 meters 13 mm at 100 meters at 100 yards Average values depending on brightness setting MOA Minute Of Angle 1MOA 30 mm at 100 meters 1 at 100 yards NVD Night Vision Device 1 2 2 Model 7000SC 7000L 7000SC 2X and 7000L 2X Length 7000SC 160 mm 6 3 7000SC 2X 195 mm 7 7 7000L 200 mm 7 9 7000L 2X 235 mm 9 3 Width height 7000SC L 55 mm 2 2 7000SC L 2X 60 mm 2 4 Weight 7000SC 200 gram 7 0 oz 7000SC 2X 290 gram 10 2 oz 7000L 225 gram 7 9 oz 7000L 2X 315 gram 11 1 oz Surface finish Carbon Black or Silver Metalic SM only 7000SC semi matte Mounting 2 rings 30 mm diameter Distance between rings 7000SC min 50 mm 2 0 max 115 mm 4 5 7000L min 60 mm 2 4 max 155 mm 6 1 Switch dot brightness 10 pos 1 Off 9 daylight of which 1 Extra Bright Max temperature range 30 C to 60 C 20 to 140 F Water resistance Waterproof to 2 m 7 ft water depth 1 2 3 Model CompC and CompC 2X Length CompC 120 mm 4 7 CompC 2X 155 mm 6 1 Width height CompC 55 mm 2 2 CompC 2X 60 mm 2 4 Weight CompC 185 gram 6 5 oz CompC 2X 275 gram 9 7 oz Surface finish Carbon Black or Silver Metallic SM only CompC semi matte Mounting One wide ring 30 mm di
Download Pdf Manuals
Related Search