CE EMC TEST REPORT
Contents
1. MODEL PAP2T Adapter TEST MODE Mode 1 2 INPUT POWER 230Vac 50 Hz ENVIRONMENTAL 16 deg C 44 RH CONDITIONS 974 hPa TESTED BY Mitch Jen POWER PORT VOLTAGE TEST POLARITY PERFORMANCE OBSERVATION kV POINT CRITERION L1 L2 NOTE 1 NOTE 1 There was no change compared with the initial operation during the test Report No CE941006H04B 56 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 5 8 IMMUNITY TO CONDUCTED DISTURBANCES INDUCED BY RF FIELDS CS 5 8 1 TEST SPECIFICATION Basic Standard IEC 61000 4 6 Frequency Range 0 15 MHz 80 MHz Field Strength 3 V Modulation 1kHz Sine Wave 8096 AM Modulation Frequency Step 1 of fundamental Coupled Cable Power Mains Unshielded Signal Control Line Coupling Device CDN M2 2 wires CDN T8 CDN T2 Dwell Time 3 seconds 5 8 2 TEST INSTRUMENTS DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL Feb 01 2006 Coupling Decoupling Network Fischer Custom Communications Inc FCC 801 T4 Oct 05 2006 Coupling Decoupling Network Fischer Custom Communications Inc FCC 801 T8 02036 Oct 05 2006 Coupling Decoupling Network NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 The test was performed in Chamber Room No B Report No CE941006H04B 57 Report Format Version 2 0 4 Reference N2. CORP TEST REPORT REPORT NO CE941006H04B MODEL NO PAP2T PAP2T XX RECEIVED Dec 19 2005 TESTED Dec 20 to 27 2005 ISSUED Dec 28 2005 APPLICANT Cisco Linksys LLC ADDRESS 121 Theory Drive Irvine CA 92617 USA ISSUED BY Advance Data Technology Corporation LAB LOCATION 81 1 Lu Liao Keng 9 Ling Wu Lung Tsuen Chiung Lin Hsiang Hsin Chu Hsien Taiwan This test report consists of 83 pages in total It may be duplicated completely for legal use with the approval of the applicant It should not be reproduced except in full without the written approval of our laboratory The client should not use it to claim product endorsement by CNLA NVLAP A2LA or any government agencies The test results in the report only apply to the tested sample The test results in this report are traceable to the national or international standards 8 NVLAD q p 1 0536 Lab Code 200376 0 No 2177 01 ILAC MRA Report No CE941006H04B 1 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP Table of Contents 1 Sodio 5 2 SUMA YOTE SI TTE UI Queens 7 2 1 MEASUREMENT UNCERTAINTY 8 3 GENERAL INFORMATION 9 3 1 GENERAL DESCRIPTION OF EUT uuu siete eoo hp tia aate 9 3 2 DESCRIPTION OF TEST MODE nennen 10 3 3 GENERAL DESCRIPTION OF APPLIED STANDARDS 10 3 4
3. 66 7 APPENDIX INFORMATION ON THE TESTING LABORATORIES 83 Report No CE941006H04B 4 Report Format Version 2 0 4 Reference No 941219H04 CORP 1 CERTIFICATION PRODUCT Internet Phone Adapter BRAND NAME Linksys MODEL NO PAP2T PAP2T XX TESTED Dec 20 to 27 2005 TEST ITEM ENGINEERING SAMPLE APPLICANT Cisco Linksys LLC STANDARDS CISPR 22 1997 1 2000 2 2002 Class B EN 55022 1998 A1 2000 EN 55024 1998 A1 2001 A2 2003 Class B 2 2003 61000 3 2 2000 IEC 61000 4 2 2001 see note below IEC 61000 4 3 2002 A1 2002 EN 61000 3 3 1995 A1 2001 IEC 61000 4 4 2004 IEC 61000 4 5 2001 IEC 61000 4 6 2003 1 2004 IEC 61000 4 8 2001 IEC 61000 4 11 2004 The above equipment Model PAP2T has been tested by Advance Data Technology Corporation and found compliance with the requirement of the above standards Approval signature on next page Report No CE941006H04B 5 Report Format Version 2 0 4 Reference No 941219H04 CORP CERTIFICATION Continued The test record data evaluation amp Equipment Under Test EUT configurations represented herein are true and accurate accounts of the measurements of the sample s EMC characteristics under the conditions specified in this report PREPARED BY Dee 26 2005 Betty Liu TECHNICAL Ivan ns ACCEPTANCE DATE Dec 26 2005 Responsible for EMI Ivan
4. Value 0 15 1 00 10 00 30 00 Report No CE941006H04B 17 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 1 8 TEST RESULTS 2 EUT Internet Phone Adapter MODEL PAP2T INPUT POWER 230Vac 50 Hz 6dB BANDWIDTH ENVIRONMENTAL 25 deg 55 RH CONDITIONS 974 hPa TESTED BY Mike Hsieh ee eee _ Factor AV QP 4 4434 166 00 56 00 21 66 Som os sess sess sess 20m or as 1428172 8600 4600 4342 5 2215 072 3974 40 46 56 00 46 00 15 64 6 23 879 138 36 04 37 42 160 00 50 00 22 58 REMARKS 1 and AV are abbreviations of quasi peak and average individually 2 The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3 The emission levels of other frequencies were very low against the limit 4 Margin value Emission level Limit value 5 Correction factor Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value 110 100 imi ET wo LIU HH 0 15 1 00 10 00 30 00 Report No CE941006H04B 18 Report Format Version 2 0 4 Reference 941219H04 CORP Internet Phone Adapter MODEL PAP2T INPUT POWER
5. mw 4 t TA e 4 gt buic 2 M M oM H L Y xn ca WP pw lt lt lt eg Report No CE941006H04B 46 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP DESCRIPTION OF TEST POINT Mode 2 Report No CE941006H04B 47 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 5 5 RADIATED RADIO FREQUENCY ELECTROMAGNETIC FIELD IMMUNITY TEST RS 5 5 1 TEST SPECIFICATION Basic Standard IEC 61000 4 3 Frequency Range 80 MHz 1000 MHz Field Strength 3 V m Modulation 1kHz Sine Wave 80 AM Modulation Frequency Step 1 of fundamental Polarity of Horizontal and Vertical Antenna Test Distance 3 m Antenna Height 1 5m Dwell Time 3 seconds 5 5 2 TEST INSTRUMENTS DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL AR Power Amplifier 150W1000M3 311567 AR Power Amplifier 60S1G3M1 304334 AR LOG ANTENNA AT5080ANT 309740 Electric Field Probe NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 The test was performed in Chamber Room No B Report No CE941006H04B 48 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 5 3 TEST PROCEDURE The test procedure was in accordance with IEC 61000 4 3 a The testing was
6. Photographs of the Test Configuration NOTE FLOOR STANDING EQUIPMENT The equipment to be tested is placed on an insulating support of 0 1 meters height above a ground reference plane All relevant cables shall be provided with the appropriate coupling and decoupling devices at a distance between 0 1 meters and 0 3 meters from the projected geometry of the EUT on the ground reference plane Report No CE941006H04B 58 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 8 5 TEST RESULTS MODE 1 2 Internet Phone umm ee m _ ENVIRONMENTAL 25 deg C 53 CONDITIONS 974 ed TESTED BY Duke Tseng FOR MAINS POWER Field Frequenc 2 Strength Cable Memes een NN 0 15 80 AC powerline CDN M2 Note 1 A FOR SIGNAL CONTROL LINE The LAN port and WAN port were tested separately Voltage Level Cable Vr m s Frequency MHz Injection Obser Performance Method vation Criterion 3 Noe 3 ren NOTE 1 There was no change compared with the initial operation during the test 2 There were disturbance noises found via phone during the test but self recoverable after the test According to the specification of the manufacturer this phenomena is acceptable The manufacturer agrees to have a clear statement about this in the users manual to avoid misunderstanding
7. Report No CE941006H04B 59 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 9 POWER FREQUENCY MAGNETIC FIELD IMMUNITY TEST 5 9 1 TEST SPECIFICATION Basic Standard IEC 61000 4 8 Frequency Range 50Hz Field Strength 1 A m Observation Time 1 minute Inductance Coil Helmholtz coil diameter 1 5m 5 9 2 TEST INSTRUMENTS DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL BELL Triaxial EIf Magnetic Field Meter MONTENA Helmholt HC150 360 4090 Dec 10 2006 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 The test was performed in EMS room 5 9 3 TEST PROCEDURE The equipment is configured and connected to satisfy its functional requirements The power supply input and output circuits shall be connected to the sources of power supply control and signal c The cables supplied or recommended by the equipment manufacturer shall be used 1 meter of all cables used shall be exposed to the magnetic field Report No CE941006H04B 60 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 9 4 TEST SETUP 1 5m Double induction Coil Test Generator Reference Ground Plane For the actual test configuration please refer to related item Photographs of the Test Configuration NOTE TABLETOP EQUIPMENT The eq
8. The emission levels of other frequencies were very low against the limit 4 Margin value lt Emission level Limit value 5 Correction factor lt Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value 7 According to Note of Table 4 of CISPR 22 EN 55022 a relaxation of 10 dB over the frequency range of 6MHz to 30MHz is allowed for high speed services having significant spectral density in this band However this relaxation is restricted to the common mode disturbance converted by the cable from the wanted signal There is no relaxation of 10dB 110 EIN a LH L1 LLL Ka Lil DL Pat CE941006H04B 24 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 3 RADIATED EMISSION MEASUREMENT 4 3 1 LIMITS OF RADIATED EMISSION MEASUREMENT TEST STANDARD EN55022 Class A at 10m Class B at 10m FREQUENCY MHz dBuV m dBuV m 30 230 230 1000 NOTE 1 The lower limit shall apply at the transition frequencies 2 Emission level dBuV m 20 log Emission level uV m 3 All emanations from a class A B digital device or system including any network of conductors and apparatus connected thereto shall not exceed the level of field strengths specified above 4 3 2 TEST INSTRUMENTS DESCRIPTION amp CALIBRATED
9. c The correspondent test program of test instrument to measure the current harmonics emanated from EUT is chosen The measure time shall be not less than the time necessary for the EUT to be exercised 4 4 4 TEST SETUP For the actual test configuration please refer to the related item Photographs of the Test Configuration 4 4 5 EUT OPERATING CONDITIONS Same as 4 1 6 Report No CE941006H04B 39 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 4 6 TEST RESULTS MODE 1 EUT Internet Phone MODEL PAP2T Adapter POWER FUNDAMENTAL 229 7 Vrms VOLTAGE AMPERE 0 062 Arms POWER FACTOR POWER ENVIRONMENTAL 16 deg C 50 96 RH CONSUMPTION 9 3 9 W CONDITIONS 974 hPa TESTED BY Mitch Jen 1 Limits are not specified for equipment with a rated power of 5W or less other than lighting equipment 2 According to EN 61000 3 2 2000 the manufacturer shall specify the power of the apparatus This value shall be used for establishing limits The specified power shall be within 10 of the measured power 4 4 7 TEST RESULTS MODE 2 _ Adapter POWER FUNDAMENTAL 229 7 Vrms VOLTAGE AMPERE 0 054 Arms POWER FACTOR POWER ENVIRONMENTAL 16 deg 50 RH CONSUMPTION 5 387 W CONDITIONS 974 hPa TESTED BY Mitch Jen 1 Limits are not specified for equipment with a rated power of 75W or less other than lighting equipment 2 According to EN 61000 3 2 2000
10. network LISN Other support units were connected to the power mains through another LISN b Voltage at the measurement port of the ISN was detected the reading was corrected by adding the voltage division factor of the ISN and was compared to the voltage limits c The disturbance levels and the frequencies of at least six highest disturbances were recorded from each telecommunication port which comprises the EU T 4 2 4 DEVIATION FROM TEST STANDARD No deviation Report No CE941006H04B 21 Report Format Version 2 0 4 Reference No 941219H04 4 2 5 TEST SETUP Vertical Refer ee Ground Plane EUT 40cm ISN Note 1 Supportunits were connected to second LISN ence Em Horizontal Reference CORP TM G G lt lt Ground Plane 2 Both of LISNs AMN and ISN are 80 cm from EUT and atleast 80 cm from other units and other metal planes supportunits For the actual test configuration please refer to the related item Photographs of the Test Configuration NOTE a The methods of conformance testing were selected according to the Alternative 1 EN 55022 1998 A1 2000 A2 2003 section 9 5 1 1 or Alternative 2 EN 55022 1998 A1 2000 A2 2003 section 9 5 1 2 of measurement method using an ISN with a longitudinal conversion loss LCL as defined in rule b When measurements were performed on a single unscreened balanced pair an adequate ISN
11. 230Vac 50 Hz 6dB BANDWIDTH ENVIRONMENTAL 25 deg C 55 RH mmm CONDITIONS 974 hPa TESTED BY Mike Hsieh Emission Margin Level 9 MHz dB A _ QP AV oin 040 asso asso 8489 sae 1600 2 0173 040 4795 48 35 64 83 54 83 1648 3 0248 040 3931 3971 61 84 51 84 2213 5 2119 0 61 4053 4124 56 00 4600 4476 _6 23 066 172 3889 40 61 60 00 50 00 19 39 REMARKS 1 Q P and AV are abbreviations of quasi peak and average individually 2 The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3 The emission levels of other frequencies were very low against the limit 4 Margin value lt Emission level Limit value 9 Correction factor 7 Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value 110 100 0 15 1 00 10 00 30 00 Report No CE941006H04B 19 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 2 CONDUCTED EMISSION MEASUREMENT TELECOMMUNICATION PORTS 4 2 1 LIMIT OF CONDUCTED COMMON MODE DISTURBANCE TELECOMMUNICATION PORTS FOR CLASS A EQUIPMENT FREQUENCY Voltage Limit dBuV Current Limit dBuA MHz Quasi peak Average Quasi peak Average 0 15 0 5 97 87 84 74 53 43 40 30 0 5 30 0 FOR CLASS B EQUI
12. ADT CORP RJ11 cable 1 5m RJ11 cable 1 5m s 1 TELEPHONE 2 TELEPHONE UTP cable 10m gt 3 NOTEBOOK COMPUTER CONTROL ROOM NOTE 1 Support units 3 were kept in the control room during the test 2 Please refer to the photos of test configuration in Item 6 also Report No CE941006H04B 12 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 EMISSION TEST 4 1 CONDUCTED EMISSION MEASUREMENT 4 1 1 LIMITS OF CONDUCTED EMISSION MEASUREMENT TEST STANDARD EN55022 Class B dBuV FREQUENCY MHz Class A dBuV Class B dBuV 0 15 05 79 66 66 56 56 46 050 50 73 60 56 46 50 300 73 6 6 5 NOTE 1 The lower limit shall apply at the transition frequencies 2 The limit decreases in line with the logarithm of the frequency in the range of 0 15 to 0 50 MHz 3 All emanations from a class A B digital device or system including any network of conductors and apparatus connected thereto shall not exceed the level of field strengths specified above 4 1 2 TEST INSTRUMENTS DESCRIPTION amp CALIBRATED MODEL NO SERIAL NO MANUFACTURER UNTIL ROHDE amp SCHWARZ ESCS 30 847124 029 Dec 14 2006 Test Receiver Line Impedance Stabilization ENV 216 100072 Oct 05 2006 Network for EUT NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to
13. Emission Limit TO Antenna Table Correction IMS Level dBuV m Pi Angle Factor dBuV m Degree dBuV 1 6400 1790QP 3000 12 10 400H 294 1030 760 2 111 1940QP 3000 31060 400H 136 72 1220 a 18227 21 00QP 3000 900 400H 155 1050 1050 6 37503 3080QP 37 00 6 20 158H 57 1260 1830 UN ME EN JE 450 21 _ Fem sro 10H 25 10 87500 3010QP 3700 6 90 1 00H 255 210 2790 REMARKS 1 Emission level dBuV m Raw Value dBuV Correction Factor dB m 2 Correction Factor dB m Antenna Factor dB m Cable Factor dB 3 The other emission levels were very low against the limit 4 Margin value Emission level Limit value Level dBuWV T lI 27 100 200 300 400 500 Bu FOO 800 900 1003 Frequency MHz Report No CE941006H04B 30 Report Format Version 2 0 4 Reference No 941219H04 CORP EUT MEMEL PRONE MODEL PAP2T Adapter INPUT POWER DETECTOR Quasi Peak FREQUENCY RANGE 30 1000 MHz FUNCTION amp BANDWIDTH 120kHz ENVIRONMENTAL 16 deg 66 96 RH m CONDITIONS 974 hPa TESTED BY Mike Hsieh ANTENNA POLARITY amp TEST DISTANCE VERTICAL AT 10 M Fre Emission Limit TS Antenna Table Correction MS Level dBuV m s jd Angle Factor dBuV m Degree dBuV 1 6403 21400 3000 860 100v 141 1370
14. Mode 1 0412191104 RS TEST Mode 2 9412191104 Report No CE941006H04B 72 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 1 Report No CE941006H04B 73 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP Report CE941006H04B 74 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 2 T h e Report No CEo41006H04B 75 Report Format Version 2 0 4 Reference NolJo41219H04 T ADT CORP EFT TEST RJ 11 Report No CE941006H04B 76 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP SURGE amp VOLTAGE DIPS AND INTERRUPTIONS TEST Mode 1 941219H04 SURGE amp VOLTAGE DIPS AND INTERRUPTIONS TEST Mode 2 D D Report No CE941006H04B 77 Report Format Version 2 0 4 Reference No 941219H04 CORP CONDUCTED SUSCEPTIBILITY TEST Mode 1 941219H04 MEL 2 Report No CE941006H04B 78 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP CONDUCTED SUSCEPTIBILITY TEST RJ 1 LE Y 4 941219H04 EV Report No CE941006H04B 79 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP CONDUCTED SUSCEPTIBILITY TEST Mode 2 941219H04 941219H04 Report No CE
15. NML ROC and NIST USA 2 The test was performed in ADT Shielded Room No 3 The VCCI Con A Registration No is C 817 Report No CE941006H04B 13 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 1 3 TEST PROCEDURE a The EUT was placed 0 4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network LISN Other support units were connected to the power mains through another LISN The two LISNs provide 50 Ohm 50uH of coupling impedance for the measuring instrument b Both lines of the power mains connected to the EUT were checked for maximum conducted interference c The frequency range from 150 kHz to 30 MHz was searched Emission levels over 10dB under the prescribed limits could not be reported 4 1 4 DEVIATION FROM TEST STANDARD No deviation 4 1 5 TEST SETUP Vertical Reference Ground Plane Test Receiver St a eus FEE 40cm EM 2a 80cm LIS di NN Horizontal Reference Ground Plane Note 1 Support units were connected to second LISN 2 Both of LISNs AMN are 80 cm from EUT and at least 80 from other units and other metal planes For the actual test configuration please refer to the related item Photographs of the Test Configuration Report No CE941006H04B 14 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 1 6 EUT CONDI
16. Note D 8 _ NOTES 1 The EUT found disturbance noises on telephone handset during the test but could be self recoverable after the test Report No CE941006H04B 53 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 7 SURGE IMMUNITY TEST 5 7 1 TEST SPECIFICATION Basic Standard Wave Shape Test Voltage Surge Input Output Generator Source Impedance Polarity Phase Angle degree Pulse Repetition Rate Number of Tests IEC 61000 4 5 Combination Wave 1 2 50 us Open Circuit Voltage 8 20 us Short Circuit Current Power Line 0 5kV 1 kV L1 L2 2 ohm between networks Positive Negative 0 90 180 270 1 time min maximum 5 positive and 5 negative at selected points 5 7 2 TEST INSTRUMENTS DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL KeyTek EMS Simulator EMC Pro 9712339 Feb 22 2006 KeyTek Coupler Decoupler CM I OCD 9908190 KeyTek Coupler Decoupler CM TELCD 9906197 Adapter EMC Pro SU1ADA 001 Dec 24 2006 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 The test was performed in EMS room A Report No CE941006H04B Reference No 941219H04 54 Report Format Version 2 0 4 ADT CORP 5 7 3 TEST PROCEDURE a For EUT power supply The surge is to be applied to the EUT power supply terminals via t
17. Peng TECHNICAL a th Ten ACCEPTANCE DATE Dec 26 2005 Responsible for EMS Mitch Jen My May Chen Deputy Manager APPROVED BY DATE Dee 28 2005 Note The power consumption of EUT is 5 375W 5 387W which is less than 75W and no limits apply Therefore it is deemed to comply with EN 61000 3 2 2000 without any testing Report No CE941006H04B 6 Report Format Version 2 0 4 Reference No 941219H04 2 SUMMARY TEST RESULTS The EUT has been tested according to the following specifications Standard Type Result Remarks Meets Class B Limit Conducted Test PASS Minimum passing margin is 8 56 dB at 0 150 MHz 2000 2 2003 Ports Conducted Test PASS Minimum passing margin is Class B 10 73 dB at 10 000 MHz Meets Class B Limit Radiated Test PASS Minimum passing margin is 2 4 dB at 52 87 MHz The power consumption of PASS EUT is less than 75W and no limits apply en ra LM fluctuations amp PASS Meets the requirements IMMUNITY EN 55024 1998 A1 2001 A2 2003 Standard Type Result 61000 4 2 2001 Electrostatic discharge PASS Meets the requirements of immunity test Performance Criterion A Radiated radio IEC 61000 4 3 2002 frequency Meets the requirements of A1 2002 electromagnetic field Performance Criterion A immunity test IEC 61000 4 4 2004 Electrical fast transient PASS Meets the requirements of
18. Reference Plane by an insulating support of 0 1 meter thickness The GRP consisted of a sheet of aluminum that is at least 0 25mm thick and 2 5 meters square connected to the protective grounding system and extended at least 0 5 meters from the EUT on all sides Report No CE941006H04B 44 Report Format Version 2 0 4 Reference No 941219H04 5 4 5 TEST RESULTS MODE 1 2 Internet Phone MODEL PAP2T Adapter ENVIRONMENTAL 21 deg 60 TEST RESULTS OF DIRECT APPLICATION Discharge Polarity Contact o Performance Note 1 Note No conductive surfaces found therefore no contact discharge was executed Description of test point Please refer to ESD test photo 1 Power connector 2 RJ 45 connector 3 RJ 11 connector 4 LED indicator 5 Opening 6 Reset button TEST RESULTS OF INDIRECT APPLICATION Discharge Polarity Test Point zen m Performance Level KV Criterion 2 4 1 4 Note 1 Note 1 Description of test point 1 Front side 2 Right side 3 Left side 4 Rear side NOTES 1 There was no change compared with the initial operation during the test Report No CE941006H04B 45 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP DESCRIPTION OF TEST POINT Mode 1 941219904 ee De u x am he EANA uz T PII 122 er ee 24 aie CA N K O Fa L
19. USA 2 The test was performed in ESD room A 5 4 3 TEST PROCEDURE The discharges shall be applied in two ways a Contact discharges to the conductive surfaces and coupling planes The EUT shall be exposed to atleast 200 discharges 100 each at negative and positive polarity at a minimum of four test points One of the test points shall be subjected to at least 50 indirect discharges to the center of the front edge of the horizontal coupling plane The remaining three test points shall each receive at least 50 direct contact discharges If no direct contact test points are available then at least 200 indirect discharges shall be applied in the indirect mode Test shall be performed at a maximum repetition rate of one discharge per second b Air discharges at slots and apertures and insulating surfaces On those parts of the EUT where it is not possible to perform contact discharge testing the equipment should be investigated to identify user accessible points where breakdown may occur Such points are tested using the air discharge method This investigation should be restricted to those area normally handled by the user A minimum of 10 single air discharges shall be applied to the selected test point for each such area Report No CE941006H04B 42 Report Format Version 2 0 4 Reference No 941219H04 CORP The basic test was in accordance with 61000 4 2 a Electrostatic discharge
20. for two wires were used when performed on unscreened cables containing two balanced pairs an adequate ISN for four wires were used c The communication function of EUT was executed and ISN was connected between EUT and associated equipment and the ISN was connected directly to reference ground plane 4 2 6 EUT OPERATING CONDITIONS Same as 4 1 6 Report No CE941006H04B Reference No 941219H04 Report Format Version 2 0 4 4 2 7 TEST RESULTS MODE 1 eur Internet Phone Adapter MODEL PAP2T INPUT POWER rest MODE Van 50H TELECOM PORT 10Mbps Current BANDWIDTH BANDWIDTH ENVIRONMENTAL 27 deg C 55 RH CONDITIONS 974 hPa TESTED BY Mike Hsieh dB uV dB E dB AEn MHz dB AV AV EBENE FN AU ERE AUTRE MR 211 441 047 9311 9000 2000 2009 Emission Margin with Corr Reading Value Limit 10dB Level relaxation Factor 6003 063 fri 782 4000 4238 5 10 002 0 71 28 15 2886 40 00130 00 11 14 2114 6 12 105 0 71 264 335 40 00 30 00 36 65 __ 46 65 REMARKS Q P and AV are abbreviations of quasi peak and average individually The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary The emission levels of other frequencies were very low
21. is a kind of IT equipment and according to the specifications of the manufacturers must comply with the requirements of the following standards CISPR 22 1997 A1 2000 A2 2002 Class B EN 55022 1998 1 2000 EN 55024 1998 A1 2001 2 2003 Class B A2 2003 EN 61000 3 2 2000 Class A IEC 61000 4 2 2001 EN 61000 3 3 1995 A1 2001 IEC 61000 4 3 2002 1 2002 IEC 61000 4 4 2004 IEC 61000 4 5 2001 IEC 61000 4 6 2003 A1 2004 IEC 61000 4 8 2001 IEC 61000 4 11 2004 All tests have been performed and recorded as per the above standards Report No CE941006H04B 10 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 3 4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units The following support units or accessories were used to form a representative test configuration during the tests Model No 2 D is WE 97286141 Fr TELEPHONE Romeo TE 812 97280926 j NOTEBOOK Latitude B COMPUTER PEL C600 C500 _ 00891 No Signal cable description 1 5 m nonshielded telephone terminated with RJ11 connector w o core 1 5 m nonshielded telephone terminated with RJ11 connector w o core 3 NA Note 1 All power cords of the above support units are unshielded 1 8m Report No CE941006H04B 11 Report Format Version 2 0 4 Reference No 941219H04
22. the manufacturer shall specify the power of the apparatus This value shall be used for establishing limits The specified power shall be within 10 of the measured power Report No CE941006H04B 34 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 5 VOLTAGE FLUCTUATION AND MEASUREMENT 4 5 1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKER MEASUREMENT TEST STANDARD EN61000 3 3 TEST ITEM LIMIT NOTE P4 means short term flicker indicator P means long term flicker indicator Tu ms means maximum time that dt 2 exceeds 3 3 4 dmax means maximum relative voltage Cmax dc 96 3 3 dc means relative steady state i change 4 5 2 TEST INSTRUMENTS Description amp Manufacturer ____ Serial No Calibrated Until EMC PARTNER HAR1000 086 Jan 12 2006 EMC Emission Tester NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 The test was performed in EMS room 4 5 3 TEST PROCEDURE a The EUT was placed on the top of a wooden table 0 8 meters above the ground and operated to produce the most unfavorable sequence of voltage changes under normal operating conditions b During the flick measurement the measure time shall include that part of whole operation cycle in which the EUT produce the most unfavorable sequence of
23. used as intended The performance level may be replaced by a permissible loss of performance During the test degradation of performance is allowed However no change of operating state if stored data is allowed to persist after the test If the minimum performance level or the permissible performance loss is not specified by the manufacturer then either of these may be derived from the product description and documentation and by what the user may reasonably expect from the equipment if used as intended Loss of function is allowed provided the function is self recoverable or can be restored by the operation of the controls by the user in accordance with the manufacturer s instructions Functions and or information stored in non volatile memory or protected by a battery backup shall not be lost Report No CE941006H04B Reference No 941219H04 40 Report Format Version 2 0 4 CORP 5 3 PARTICULAR CRITERIA DESCRIPTION FOR LAN FUNCTION OF EUT During and after the test the EUT shall operate without error rate beyond the figure defined by the manufacturer requests for retry beyond the figure defined by the manufacturer speed of data transmission rate beyond figure defined the manufacturer protocol failure loss of link Error rate request for retry and speed of data transmission rate may be degraded during the application of the test Degradation of
24. voltage changes The observation period for short term flicker indicator is 10 minutes and the observation period for long term flicker indicator is 2 hours Report No CE941006H04B 35 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 5 4 TEST SETUP For the actual test configuration please refer to the related item Photographs of the Test Configuration 4 5 5 EUT OPERATING CONDITIONS Same as 4 1 6 Report No CE941006H04B 36 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 5 6 TEST RESULTS MODE 1 EUT Internet Phone MODEL PAP2T Adapter POWER VOLTAGE AMPERE 0 062 Arms POWER FACTOR OBSERVATION 10 mins ENVIRONMENTAL 16 deg C 50 RH PERIOD TP CONDITIONS 974 hPa FUNDAMENTAL 229 7 Vrms TESTED BY Mitch Jen TEST PARAMETER ae ERI LIMIT REMARKS 00 80 pe _ dap 000 4 Pas _ 00 3 Pes _ NOTE 1 P means short term flicker indicator 2 P means long term flicker indicator 3 T4 means maximum time that dt exceeds 3 3 4 dmax means maximum relative voltage change 5 dc means relative steady state voltage change Report No CE941006H04B 37 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 5 7 TEST RESULTS MODE 2 EUT Internet Phone MODEL PAP2T Adapter POWER VOLTAGE AMPERE 0 054 Arms POWER FACTOR OBSERVATION 10 mins ENVIRONMENTAL 16 d
25. 760 2 111 23200 3000 680 100 12 noo 1220 3 12500 21300 3000 870 100v 0 890 1240 6 37500 2790QP 3700 910 100v 286 960 1830 8 6250 37 00 5 20 279v 239 800 2380 2 50 QP REMARKS 1 Emission level dBuV m Raw Value dBuV Correction Factor dB m 2 Correction Factor dB m Antenna Factor dB m Cable Factor dB 3 The other emission levels were very low against the limit 4 Margin value Emission level Limit value Level dBuWV T 50 40 30 40 27 100 200 300 400 500 Bu FOO 800 900 1003 Frequency MHz Report No CE941006H04B 31 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 4 HARMONICS CURRENT MEASUREMENT 4 4 1 LIMITS OF HARMONICS CURRENT MEASUREMENT TEST STANDARD EN61000 3 2 Limits for Class D equipment Harmonics Max permissible Harmonics Max permissible Max permissible harmonics current Order harmonics current per harmonics current n n mA W A Odd Harmonics onl 2 30 3 3 4 2 30 5 1 14 5 707 7 9 040 9 11 033 11 13 10 21 13 15 lt lt 39 0 15 15 15 lt lt 39 2 11 08 4 4 043 4 67030 242 8 lt lt 40 0 23 8 4 NOTE 1 classifications of equipment are defined in Section 5 of EN 61000 3 2 2000 2 The above limits for all equipment except for lighting equipment are fo
26. 941006H04B 80 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP CONDUCTED SUSCEPTIBILITY TEST RJ 11 x 941219H04 Report No CE941006H04B 81 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP POWER FREQUENCY MAGNETIC FIELDS TEST Mode 1 POWER FREQUENCY MAGNETIC FIELDS TEST Mode 2 Report No CE941006H04B 82 Report Format Version 2 0 4 Reference No 941219H04 CORP 7 APPENDIX INFORMATION ON THE TESTING LABORATORIES We ADT Corp were founded in 1988 to provide our best service in EMC Radio Telecom and Safety consultation Our laboratories are accredited and approved by the following approval agencies according to ISO IEC 17025 USA FCC NVLAP UL A2LA Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA CSA R O C CNLA BSMI DGT Netherlands Telefication Singapore PSB GOST ASIA MOU Russia CERTIS MOU Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site www adt com tw index 5 phtml If you have any comments please feel free to contact us at the following Linko EMC RF Lab Hsin Chu EMC RF Lab Tel 886 2 26052180 Tel 886 3 5935343 Fax 886 2 26052943 Fax 886 3 5935342 Hwa Ya EMC RF Safety Telecom Lab Tel 886 3 3183232 Fax 886 3 3185050 Email service adt com tw Web Site www adt com tw The address and roa
27. ADVANTEST Spectrum Analyzer R3271A 85060311 July 07 2006 amp SCHWARZ ESVS 30 841977 002 Oct 08 2006 Test Receiver CHASE Broadband Antenna CBL6111C 2730 Jun 08 2006 Schwarzbeck Horn Antenna BBHA9120 D1 D123 oep 23 2006 ochwarzbeck Horn Antenna BBHA 9170 BBHA9170153 Jan 31 2006 SCHWARZBECK VHBA9123 459 Jun 26 2006 Biconical Antenna SCHWARZBECK UPA6108 1148 Jun 26 2006 Periodic Antenna Switches 6100175593 Jul 19 2006 Cable CHASE 9913 30 STBCAB 30M Jul 19 2006 Cable 1GHz 021 5 14 Note 1 The calibration interval of the above test instruments is 12 months 36 months for Periodic Antenna and the calibrations are traceable to NML ROC and NIST USA 2 These equipment are used for the final measurement 3 The horn antenna and HP preamplifier model 8449B are used only for the measurement of emission frequency above 1GHz if tested The test was performed in ADT Open Site No B The VCCI Site Registration No is R 847 The FCC Site Registration No is 92753 The CANADA Site Registration No is IC 4824 2 Report No CE941006H04B 25 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 3 3 TEST PROCEDURE a The EUT was placed on the top of a rotating table 0 8 meters above the ground at a 10 meter open field site The table was rotated 360 degrees to determine the position of the highest radiation The E
28. DESCRIP HON OF SUPPORT NS 11 4 EMISSION TEST 13 4 1 CONDUCTED EMISSION MEASUREMENT 13 4 1 1 LIMITS OF CONDUCTED EMISSION MEASUREMENTT 13 41 2 TEST INSIRUNIE NIP uu E 13 4 15 TEST PROCEDURE cett nme UM ETIN IEEE EMEN 14 4 1 4 DEVIATION FROM TEST STANDARD Se aaa 14 SO ee 14 41 65 FUTOPERATINSOGCONDIIIDNS uuu ee 15 4 1 7 TEST RESULTS MODE 1 sees 16 TESI RE ULIS 18 4 2 CONDUCTED EMISSION MEASUREMENT TELECOMMUNICATION 20 4 2 1 LIMIT OF CONDUCTED COMMON MODE DISTURBANCE AT TELECOMMUNICATION PORTS 20 222 WEST INSTIRUMEN TS ass ae een 20 4 2 3 ATEST PROCEDURE en 21 4 2 4 DEVIATION FROM TEST STANDARD 21 eee eee 22 4 26 OPERATING CONDITIONS uuu mann 22 4 2 7 TEST RESULTS MODE 1 23 420 TE RESULT MODE Denen essen 24 4 3 RADIATED EMISSION MEASUREMENT 25 4 3 1 LIMITS OF RADIATED EMISSION MEASUREMENI 25 4 3 2 5 25 OA 26 4 34 DEVIATION FROM TEST STANDARD 26 4 TES SE TOP emm 27 4 3 6 EUT OPERATING CONDITIONS 4 27 NEST RE SULIS WODE Li usa mar nn 28 4 3 8 TEST RESULTS MODE 2 30 4 4 HARMONICS CURRENT MEASUREMENT 32 4 4 1 LIMITS OF HARMONICS CURRENT MEASUREMENT 32 Report No CE941006H04B 2 Report Format
29. L PAP2T Adapter INPUT POWER DETECTOR Quasi Peak FREQUENCY RANGE 30 1000 MHz FUNCTION amp BANDWIDTH 120kHz ENVIRONMENTAL 16 deg 66 96 RH m CONDITIONS 974 hPa TESTED BY Mike Hsieh ANTENNA POLARITY amp TEST DISTANCE VERTICAL AT 10 M Fre Emission Limit TS Antenna Table Correction M Level dBuV m s jd Angle Factor dBuV m PM 1 12151 2300QP 3000 7 00 100v 1090 1220 UN MS SN SE 5 25002 3010QP 3700 690 100v 186 15 90 14 20 6 35000 2790QP 3700 910 100v 3 10 70 17 20 UM CNN EE NE NEN 2420 _ mes wear sro 24 inv xu am ma _ 81007 2800QP 37 00 900 233V 214 120 2680 REMARKS 1 Emission level dBuV m Raw Value dBuV Correction Factor dB m 2 Correction Factor dB m Antenna Factor dB m Cable Factor dB 3 The other emission levels were very low against the limit 4 Margin value Emission level Limit value Level dBuWV T I 27 100 200 300 400 500 Bu FOO 800 900 1003 Frequency MHz Report No CE941006H04B 29 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 3 8 TEST RESULTS MODE 2 Adapter INPUT POWER DETECTOR Quasi Peak FREQUENCY RANGE 30 1000 MHz FUNCTION amp BANDWIDTH 120kHz ENVIRONMENTAL 16 deg 66 RH m CONDITIONS 974 hPa TESTED BY Mike Hsieh ANTENNA POLARITY amp TEST DISTANCE AT 10 M
30. PMENT FREQUENCY Voltage Limit dBuV Current Limit dBuA MHz Quasi peak Average Quasi peak Average 0 15 0 5 84 74 74 64 40 30 30 20 0 5 30 0 NOTE 1 The limits decrease linearly with logarithm of the frequency in the range 0 15 MHz to 0 5 MHz 4 2 2 TEST INSTRUMENTS DESCRIPTION CALIBRATED M ONS MODEL NO SERIAL NO MANUFACTURER UNTIL ROHDE amp SCHWARZ ESCS 30 847124 029 Dec 14 2006 Test Receiver ROHDE amp SCHWARZ LISN ESHS Z5 848773 004 Oct 05 2006 for EUT KYORITSU LISN for peripheral KNW 407 8 1395 12 Jul 19 2006 ROHDE amp SCHWARZ ISN ENY 41 838119 024 Jan 10 2006 w 60dB LCL Type Adapter ROHDE amp SCHWARZ ISN ENY 22 837497 019 Jan 10 2006 RF Cable JETBAO RG233 U Cable 01 Jul 02 2006 SMZ 11 18001 Jul 13 2006 Capacitive Voltage Probe CVP 2200 18312 Jul 13 2006 RF ABSORBING CLAMP KEMA 801 16617 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 4 The test was performed in ADT Shielded Room No 5 The Con A Registration No is C 817 Report No CE941006H04B 20 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 2 3 TEST PROCEDURE a The EUT was placed 0 4 meters from the conducting wall of the shielded room and connected to the power mains through a line Impedance stabilization
31. TEETH 49 99 TET RESULT OMODE T 50 5 6 ELECTRICAL FAST TRANSIENT BURST IMMUNITY TEST EFT 51 OO 51 3062 JES STTNO OIPUNENI u uu u uu uu ua ea 51 DOTE PROCEDURE EE E 51 52 9 5 5 TEST RE GETO MODE Te 53 5 7 SURBGEIIWIMUNIIY TEST terc 54 een 54 94 2 TESI EE 54 Report No CE941006H04B 3 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 97 5 TESI PROCEDUR E era E 55 EE er 95 TEST RESUL MODE mim 56 5 8 IMMUNITY TO CONDUCTED DISTURBANCES INDUCED BY RF FIELDS CS 57 EGR AN 57 EN 57 90 2 TEST PROCEDURE sahen 58 984 58 TES BE MODE TZ o9 5 9 POWER FREQUENCY MAGNETIC FIELD IMMUNITY TEST 60 994 EST O PECIPI ATI Nuu u EERE OEE EEES EE ETENE EEE ERRE 60 992 TE TIN TIP nassen ee 60 59 9 TEST PROCEDURE 60 SU TESTI 61 595 TES PRESS T 2 eo ass ENEE 62 5 10 VOLTAGE DIP SHORT INTERRUPTIONS VOLTAGE VARIATIONS DIP hus A TE G 63 5 10 1 TEST 63 TESTIN gt se ee er 63 5 10 9 TEST PROCEDURE 63 DATES RS ee ee een 64 5 10 5 TEST RESULTS 1 2 65 6 PHOTOGRAPHS OF THE TEST
32. TIONS 1 Turn power of all equipment 2 Support unit 3 notebook runs a test program ping exe to link of EU T 3 Support unit 1 telephone and support unit 2 telephone communicates with each other EU T 4 Repeat steps 2 3 Report No CE941006H04B 15 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 1 7 TEST RESULTS 1 Er Internet Phone Adapter MODEL PAP2T INPUT POWER 230Vac 50 Hz 6dB BANDWIDTH ENVIRONMENTAL 25 deg C 55 RH mmm CONDITIONS 974 hPa TESTED BY Mike Hsieh m Z EZ Em NE Level Factor EN dB AV AV 0 60 56 84 56 84 33 36 57 44 33 96 66 00 56 00 856 2204 2 016 060 5567 28 71 5627 29 31 65 18 55 18 891 25 87 oasa os 3939 4000 5625 4635 1685 5 0 535 062 36 94 37 56 5600 46 00 18 44 6 7203 101 3581 36 82 60 00 50 00 23 18 REMARKS 1 Q P and AV are abbreviations of quasi peak and average individually 2 The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3 The emission levels of other frequencies were very low against the limit 4 Margin value Emission level Limit value 9 Correction factor 7 Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value er
33. UT PRODUCT Internet Phone Adapter MODEL NO PAP2T PAP2T XX OWER SUPPLY Power Adapter Class 11 P DATA CABLE NA SUPPLIED Ethernet port x 1 I O PORT Phone port x 2 Power port x 1 Note 1 The EUT has two different model names which are identical to each other in all aspects except for the followings Brand Model No PAP2T Linksys PAP2T XX X could be 0 9 or A Z for different marketing From the above models model PAP2T was selected as representative model for the test and its data was recorded in this report 2 The EUT must be supplied with a power adapter and there were two models could be chosen as following Adapter 1 Input AC100 240V 0 50 60Hz Linksys PSM11R 050 Output DC5V 2 0A Max Cable 1 8m unshielded without core Adapter 2 Input AC100 240V 0 3A 50 60Hz Cable 0 4m unshielded without core Output DC5V 2 0 Cable 1 8m unshielded without core Linksys LS50V20A Report No CE941006H04B 9 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 3 For a more detailed features description please refer to the manufacturer s specifications or the User s Manual 3 2 DESCRIPTION OF TEST MODE The EUT was tested under the following test modes and its data were recorded in this report TestMode Adapter Ethernet 10Mbps Phone 1 amp 2 Ethernet 10Mbps Phone 1 amp 2 3 3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT
34. UT was set 10 meters away from the interference receiving antenna which was mounted on the top of a variable height antenna tower The antenna is a broadband antenna and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength Both horizontal and vertical polarization of the antenna are set to make the measurement For each suspected emission the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the turn table was turned from O degrees to 360 degrees to find the maximum reading The test receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode If the emission level of the EUT in peak mode was 10 dB lower than the limit specified then testing could be stopped and the peak values of the EUT would be reported Otherwise the emissions that did not have 10 dB margin would be re tested one by one using the quasi peak method or average method as specified and then reported In Data sheet peak mode and QP mode 4 3 4 DEVIATION FROM TEST STANDARD No deviation Report No CE941006H04B 26 Report Format Version 2 0 4 Reference No 941219H04 CORP 4 3 5 TEST SETUP Ant Tower 1 4m Variable EUT amp zum Support Units Ground Plane Test Receiver 0000 O O O 6 For the actual test configuration please refer to the related ite
35. Version 2 0 4 Reference No 941219H04 CORP Aka TEST INSTRUMENT 32 443 PROCEDURE u na 33 TEST ee ee ee ee 33 445 EUT OPERATING CONDITIONS eser 33 4 4 6 TEST RESULTS MODE 34 447 TEST RESULTS MODE 2 0 4 34 4 5 VOLTAGE FLUCTUATION AND FLICKER MEASUREMENT 35 4 5 1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKER MEASUREMENT 35 ES INSTRUMENT cm 35 455 WES PROCEDURE nn ed 35 ES SEE ee 36 4 5 5 EUT OPERATING CONDITIONS eee 36 490 37 4 5 7 TEST RESULTS MODE 2 38 5 IMMUNITY TEST nen ess center 39 5 1 GENERAL DESCRIPTION 39 5 2 GENERAL PERFORMANCE CRITERIA DESCRIPTION 40 5 3 PARTICULAR CRITERIA DESCRIPTION FOR LAN FUNCTION Or EU lu 41 CONDITIONS ote 41 5 4 ELECTROSTATIC DISCHARGE IMMUNITY 42 42 42 TEST INSERUMENIS u u u u u ee 42 DRE PROCEDURE 42 9 44 SET 44 94 9 TESI RESULISIMODE T 45 5 5 RADIATED RADIO FREQUENCY ELECTROMAGNETIC FIELD IMMUNITY TEST RS 48 9o TESI SPEOGIEIOATION uu 48 5 9 2 5 48 EP ROC EURE ne Ce ee 49 904 TESI SEIUP
36. against the limit Margin value Emission level Limit value Correction factor Insertion loss Cable loss Emission Level Correction Factor Reading Value According to Note 3 of Table 4 of CISPR 22 EN 55022 a relaxation of 10 dB over the frequency range of 6MHz to 30MHz is allowed for high speed services having significant spectral density in this band However this relaxation is restricted to the common mode disturbance converted by the cable from the wanted signal There is no relaxation of 10dB N gt ct ht S ft E j j ML 1 SH 111111 et ti jj tt L e ba ma Report No CE941006H04B 23 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 2 8 TEST RESULTS MODE 2 EUT Internet Phone Adapter MODEL PAP2T INPUT POWER 10Mbps Current 6dB BANDWIDTH ENVIRONMENTAL 25 deg C 50 RH m CONDITIONS 974 hPa TESTED BY Mike Hsieh AV 1 0470 1000 WS Margin with Corr 10dB relaxation Factor MHz QP AV 10 2 7 89 REMARKS 1 Q P and AV are abbreviations of quasi peak and average individually 2 The Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3
37. and NIST USA 2 The test was performed in EMS room 5 10 3 TEST PROCEDURE The EUT shall be tested for each selected combination of test levels and duration with a sequence of tree dips interruptions with intervals of 10 s minimum between each test event Each representative mode of operation shall be tested Abrupt changes in supply voltage shall occur at zero crossings of the voltage waveform Report No CE941006H04B 63 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 10 4 TEST SETUP Voltage Dips Generator For the actual test configuration please refer to the related item Photographs of the Test Configuration Report No CE941006H04B 64 Report Format Version 2 0 4 Reference No 941219H04 5 10 5 TEST RESULTS MODE 1 2 Internet Phone MODEL PAP2T Adapter TEST MODE Mode 1 2 INPUT POWER 230Vac 100Vac 50 Hz ENVIRONMENTAL 16 deg C 44 96 RH CONDITIONS ie TESTED BY Input Power for testing 230Vac 50 Hz Normal Voltage VOLTAGE PERFORMANCE PERIODS RESULTS OBSERVATION pem vam Cie CRE gt 95 PASS Note E A m A x 20 pass 6 Input Power for testing 100Vac 50 Hz Minimum Voltage VOLTAGE PERFORMANCE PERIODS RESULTS OBSERVATION 95 PASS Note 0 os mes seo le NOTES 1 There was change compared with initial operation during test 2 The EUT shut down during the
38. burst immunity test Performance Criterion B 61000 4 5 2001 Surge immunity test PASS Meets the requirements of Performance Criterion A Immunity to conducted IEC 61000 4 6 2003 disturbances induced Meets the requirements of by radio frequency Performance Criterion A fields Power frequency Meets the requirements of IEC 61000 4 8 2001 magnetic field PASS an Performance Criterion Immunity test EN61000 3 2 2000 Harmonic current Class emissions Meets the requirements of Voltage Dips 1 gt 95 reduction inter Done and Performance Criterion A IEC 61000 4 11 2004 P PASS 2 30 reduction Voltage dips short voltage variations Performance Criterion immunity tests Voltage Interruptions 1 gt 95 reduction Performance Criterion C Report No CE941006H04B 7 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 2 1 MEASUREMENT UNCERTAINTY Where relevant the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16 4 This uncertainty represents an expanded uncertainty expressed at approximately the 95 confidence level using a coverage factor of k 2 Conducted emissions 2 53 dB Radiated emissions 30MHz 1GHz 3 46 dB Report No CE941006H04B 8 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 3 GENERAL INFORMATION 3 1 GENERAL DESCRIPTION OF E
39. d al 100 Limit I LT LEE ol MR EE NES A 1o value 0 0 15 1 00 10 00 30 00 Report No CE941006H04B 16 Report Format Version 2 0 4 Reference No 941219H04 CORP Internet Phone Adapter MODEL PAP2T INPUT POWER 230Vac 50 Hz 6dB BANDWIDTH ENVIRONMENTAL 25 deg C 55 RH mmm CONDITIONS 974 hPa TESTED BY Mike Hsieh Emission Margin Level 9 tz dm OR _ SE LA 117015417040 5051 31 55 5691 3195 0579 5579 886 2354 2 0177 040 55 03 29 20 55 43 29 60 64 61 54 61 9 18 25 01 0350 040 asso 4420 5897 4897 14 68 5 0541 045 3656 56 00 4600 1944 6 7535 104 3976 4080 60 00 50 00 19 20 REMARKS 1 Q P and AV are abbreviations of quasi peak and average individually 2 Quasi peak reading value also meets average limit and measurement with the average detector is unnecessary 3 The emission levels of other frequencies were very low against the limit 4 Margin value lt Emission level Limit value 9 Correction factor 7 Insertion loss Cable loss 6 Emission Level Correction Factor Reading Value rr d LLIIL DELIS EZ 100 Limit ne a LOL LT 7 a U ER of Se AR a LT TT Y al LL LLL III x
40. d map of all our labs can be found in our web site also Report No CE941006H04B 83 Report Format Version 2 0 4 Reference No 941219H04
41. eg C 50 RH PERIOD TP CONDITIONS 974 hPa FUNDAMENTAL 229 7 Vrms TESTED BY Mitch Jen TEST PARAMETER ae ERI LIMIT REMARKS 00 80 pe _ dap 000 4 Pas _ 00 3 Pes _ NOTE 1 P means short term flicker indicator 2 P means long term flicker indicator 3 T4 means maximum time that dt exceeds 3 3 4 dmax means maximum relative voltage change 6 dc means relative steady state voltage change Report No CE941006H04B 38 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 5 IMMUNITY TEST 5 1 GENERAL DESCRIPTION Product Product Standard EN 55024 1998 1 2001 2 2003 1998 1 2001 2 2003 o 61000 4 2 Electrostatic Discharge ESD 8kV air discharge 4kV Contact discharge Performance Criterion B IEC 61000 4 3 Radio Frequency Electromagnetic Field Susceptibility Test RS 80 1000 MHz 3V m 80 AM 1kHz Performance Criterion A IEC 61000 4 4 Electrical Fast Transient Burst EFT Power line 1kV Signal line 0 5 Performance Criterion B IEC 61000 4 5 Surge Immunity Test a 1 2 50 us Open Circuit Voltage 8 20 us Short Circuit Current Power Line 1 kV line Basic Standard Specification and Performance Criterion B IEC 61000 4 6 Conducted Radio Frequency Disturbances Criteria Test CS 0 15 80 MHz 3V 8096 AM 1kHz Performance Criterion A IEC 61000 4 8 Power Frequency Magnetic Fi
42. eld Test 50 Hz 1A m Performance Criterion A IEC 61000 4 11 Voltage Dips gt 95 reduction 0 5 period Performance Criteria B li 30 reduction 25 period Performance Criterion C Voltage Interruptions gt 95 reduction 250 period Performance Criterion C Report No CE941006H04B 39 Report Format Version 2 0 4 Reference No 941219H04 5 2 GENERAL CORP PERFORMANCE CRITERIA DESCRIPTION According to Clause 7 1 of EN 55024 standard the following describes the general performance criteria CRITERION A CRITERION B CRITERION C The equipment shall continue to operate as intended without operator intervention No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the equipment is used as intended The performance level may be replaced by a permissible loss of performance If the minimum performance level or the permissible performance loss is not specified by the manufacturer then either of these may be derived from the product description and documentation and by what the user may reasonably expect from the equipment if used as intended After the test the equipment shall continue to operate as intended without operator intervention No degradation of performance or loss of function is allowed after the application of the phenomenon below a performance level specified by the manufacturer when the equipment is
43. four faces of the EUT were completely illuminated The VCP dimensions 0 5m x 0 5m was placed vertically to and 0 1 meters from the EUT Report No CE941006H04B 43 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 4 4 TEST SETUP gt 1m x x Vertical coupling plane 0 5mm Isolation Support EUT ESD DA s Nearest Wall P 80cm coupling plane Reference Ground Plane For the actual test configuration please refer to the related item Photographs of the Test Configuration NOTE TABLE TOP EQUIPMENT The configuration consisted of a wooden table 0 8 meters high standing on the Ground Reference Plane The GRP consisted of a sheet of aluminum at least 0 25mm thick and 2 5 meters square connected to the protective grounding system A Horizontal Coupling Plane 1 6m x 0 8m was placed on the table and attached to the GRP by means of a cable with 940 total impedance The equipment under test was installed in a representative system as described in section 7 of IEC 61000 4 2 and its cables were placed on the HCP and isolated by an insulating support of 0 5mm thickness A distance of 1 meter minimum was provided between the EUT and the walls of the laboratory and any other metallic structure FLOOR STANDING EQUIPMENT The equipment under test was installed in a representative system as described in section 7 of IEC 61000 4 2 and its cables were isolated from the Ground
44. he capacitive coupling network Decoupling networks are required in order to avoid possible adverse effects on equipment not under test that may be powered by the same lines and to provide sufficient decoupling impedance to the surge wave The power cord between the EUT and the coupling decoupling networks shall be 2 meters in length or shorter b Fortest applied to unshielded unsymmetrically operated interconnection lines of EUT The surge is applied to the lines via the capacitive coupling The coupling decoupling networks shall not influence the specified functional conditions of the EUT The interconnection line between the EUT and the coupling decoupling networks shall be 2 meters in length or shorter c Fortest applied to unshielded symmetrically operated interconnection telecommunication lines of EUT The surge is applied to the lines via gas arrestors coupling Test levels below the ignition point of the coupling arrestor cannot be specified The interconnection line between the EUT and the coupling decoupling networks shall be 2 meters in length or shorter 5 7 4 TEST SETUP Combination Wave Generator Coupling amp DecouplingNetwork Lx2m For the actual test configuration please refer to the related item Photographs of the Test Configuration Report No CE941006H04B 95 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 7 5 TEST RESULTS MODE 1 2 EUT
45. ion instructions Report No CE941006H04B 49 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 5 5 5 TEST RESULTS MODE 1 2 EUT phone MODEL PAP2T Adapter TEST MODE Mode 1 2 INPUT POWER 230Vac 50 Hz ENVIRONMENTAL 23 deg C 50 RH CONDITIONS 974 sa TESTED BY Anderson Chen Field Frequency Obser Performanc 80 1000 PASS VH 0 3 80 1000 NOTE There was no change compared with the initial operation during the test Report No CE941006H04B 50 Report Format Version 2 0 4 Reference No 941219H04 5 6 ELECTRICAL FAST TRANSIENT BURST IMMUNITY TEST EFT 5 6 1 TEST SPECIFICATION Basic Standard IEC 61000 4 4 Test Voltage Power Line 1 kV Signal Control Line 0 5kV Polarity Positive Negative Impulse o kHz Frequency Impulse 5 50 ns Waveshape Burst Duration 15 ms Burst Period 300 ms Test Duration Not less than 1 min 5 6 2 TEST INSTRUMENTS DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL EMC PARTNER TRANSIENT TRA1Z332N 683 Oct 13 2006 EMS Simulator MX 15 EC 9906323 Feb 28 2006 EMC PARTNER CDN UTP8 CDN UTP8 Oct 22 2006 Adapter EMCPartner SU1ADA 002 Dec 24 2006 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 The test was performed in EMS room B 5 6 3 TEST PROCEDURE Both positive and
46. m Photographs of the Test Configuration 4 3 6 EUT OPERATING CONDITIONS Same as 4 1 6 Report No CE941006H04B 27 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 3 7 TEST RESULTS MODE 1 Adapter INPUT POWER DETECTOR Quasi Peak FREQUENCY RANGE 30 1000 MHz FUNCTION amp BANDWIDTH 120kHz ENVIRONMENTAL 16 deg 66 RH m CONDITIONS 974 hPa TESTED BY Mike Hsieh ANTENNA POLARITY amp TEST DISTANCE AT 10 M Emission Antenna Table Correction Freq Limit Margin MHz Level dBuV m dB Pi Angle T Factor dBuV m Degree dBuV 1 12151 2050QP 3000 950 400H 220 830 1220 2 123501 26900 3000 310 400H 57 1450 1240 6 35003 2860QP 3700 840 373H 123 1140 1720 UN 50002 GNE eso 2150 _ Fe mee a sro ium so 250 2580 10 90000 3000QP 3700 700 101H 134 230 2770 REMARKS 1 Emission level dBuV m Raw Value dBuV Correction Factor dB m 2 Correction Factor dB m Antenna Factor dB m Cable Factor dB 3 The other emission levels were very low against the limit 4 Margin value Emission level Limit value Level dBuWV T lI 27 100 200 300 400 500 Bu FOO 800 900 1003 Frequency MHz Report No CE941006H04B 28 Report Format Version 2 0 4 Reference No 941219H04 CORP EUT MEMEL PRONE MODE
47. negative polarity discharges were applied The length of the hot wire from the coaxial output of the EFT generator to the terminals on the EUT should not exceed 1 meter The duration time of each test sequential was 1 minute The transient burst waveform was in accordance with IEC 61000 4 4 5 50ns Report No CE941006H04B 51 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 5 6 4 TEST SETUP Direct Coupling Test Setup inane xS 9 1 m 0 4 Contat io the greens uppt reference part an support EFT AB Grounding conrector ba d pererater ihe manufacturer s epecificatian RER Length to be sperilier in the test phan pane Grounding Cable tegi oferanta plane For the actual test configuration please refer to the related item Photographs of the Test Configuration Report No CE941006H04B 52 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 6 5 TEST RESULTS MODE 1 2 Internet Phone MODEL PAP2T Adapter EUT TEST MODE Mode 1 2 INPUT POWER 230Vac 50 Hz ENVIRONMENTAL 20 deg C 51 RH CONDITIONS 974 hPa TESTED BY la POWER PORT VOLTAGE POLARITY PERFORMANCE kV TEST POINT OBSERVATION CRITERION Note B Note B 0 Bo L1 L2 SIGNAL PORTS AND CONTROL PORTS VOLTAGE POLARITY PERFORMANCE TEST POINT BSERVATION kV gt gt CRITERION 50 45 Need 0080 RET
48. o 941219H04 ADT CORP 5 8 3 TEST PROCEDURE The EUT shall be tested within its intended operating and climatic conditions The test shall be performed with the test generator connected to each of the coupling and decoupling devices in turn while the other non excited RF input ports of the coupling devices are terminated by a 50 ohm load resistor c The frequency range is swept from 150 kHz to 80 MHz using the signal level established during the setting process and with a disturbance signal of 80 96 amplitude The signal is modulated with a 1 kHz sine wave pausing to adjust the RF signal level or the switch coupling devices as necessary The sweep rate shall not exceed 1 5 x 10 decades s The step size shall not exceed 1 96 of the start and thereafter 1 9o of the preceding frequency value where the frequency is swept incrementally d The dwell time at each frequency shall not be less than the time necessary for the EUT to be exercised and able to respond Sensitive frequencies such as clock frequency ies and harmonics or frequencies of dominant interest shall be analyzed separately e Attempts should be made to fully exercise the EUT during testing and to fully interrogate all exercise modes selected for susceptibility 0 1m L 0 3m x AC Powerline 0 1m wooden support Reference Ground Plane 5 8 4 TEST SETUP RF Generator For the actual test configuration please refer to the related item
49. performed in a fully anechoic chamber The transmit antenna was located at a distance of 3 meters from the EUT b The frequency range is swept from 80 MHz to 1000 MHz with the signal 80 amplitude modulated with a 1kHz sine wave The rate of sweep did not exceed 1 5 x 10 3 decade s Where the frequency range is swept incrementally the step size was 1 of fundamental c The dwell time at each frequency shall be not less than the time necessary for the EUT to be able to respond The field strength level was 3V m e The test was performed with the EUT exposed to both vertically and horizontally polarized fields on each of the four sides 5 5 4 TEST SETUP 3m measurement distance in a Full Anechoic Chamber RF Generator TEC Monitoring a system control system y For the actual test configuration please refer to the related item Photographs of the Test Configuration NOTE TABLETOP EQUIPMENT The EUT installed in a representative system as described in section of IEC 61000 4 3 was placed on a non conductive table 0 8 meters in height The system under test was connected to the power and signal wire according to relevant installation instructions FLOOR STANDING EQUIPMENT The EUT installed in a representative system as described in section of IEC 61000 4 3 was placed on a non conductive wood support 0 1 meters in height The system under test was connected to the power and signal wire according to relevant installat
50. r all applications having an active input power 75 W No limits apply for equipment with an active input power up to and including 75 W 4 4 2 TEST INSTRUMENTS Description amp Manufacturer Model No Serial No Calibrated Until EMC PARTNER HAR1000 086 Jan 12 2006 EMC Emission Tester NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 The test was performed in EMS room Report No CE941006H04B 32 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 4 4 3 TEST PROCEDURE a The EUT was placed on the top of a wooden table 0 8 meters above the ground and operated to produce the maximum harmonic components under normal operating conditions for each successive harmonic component in turn b The classification of EUT is according to section 5 of EN 61000 3 2 2000 The EUT is classified as follows Class A Balanced three phase equipment Household appliances excluding equipment as Class D Tools excluding portable tools Dimmers for incandescent lamps audio equipment equipment not specified in one of the three other classes Class B Portable tools Arc welding equipment which is not professional equipment Class C Lighting equipment Class D Equipment having a specified power less than or equal to 600 W of the following types Personal computers and personal computer monitors and television receivers
51. s were applied only to those points and surfaces of the EUT that are accessible to users during normal operation b The test was performed with at least ten single discharges on the pre selected points in the most sensitive polarity The time interval between two successive single discharges was at least 1 second d The ESD generator was held perpendicularly to the surface to which the discharge was applied and the return cable was at least 0 2 meters from the EUT e Contact discharges were applied to the non insulating coating with the pointed tip of the generator penetrating the coating and contacting the conducting substrate f Air discharges were applied with the round discharge tip of the discharge electrode approaching the EUT as fast as possible without causing mechanical damage to touch the EUT After each discharge the ESD generator was removed from the EUT and re triggered for a new single discharge The test was repeated until all discharges were complete g Atleast ten single discharges in the most sensitive polarity were applied to the Horizontal Coupling Plane at points on each side of the EUT The ESD generator was positioned vertically at a distance of 0 1 meters from the EUT with the discharge electrode touching the HCP h Atleast ten single discharges in the most sensitive polarity were applied to the center of one vertical edge of the Vertical Coupling Plane in sufficiently different positions that the
52. test but could be recovered by reset after the test Report No CE941006H04B 65 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 6 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Mode 1 941219H04 Report No CE941006H04B 66 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP CONDUCTED EMISSION TEST Mode 2 e a 9412191104 De 7 OON 941219H04 MB rn L 9 Report No CE941006H04B 67 Report Format Version 2 0 4 Reference No 941219H04 8 m gt RADIATED EMISSION TEST Mode 1 941219H04 ADI CORP Report No CE941006H04B Reference No 941219H04 68 Report Format Version 2 0 4 ADT CORP RADIATED EMISSION TEST Mode 2 9411198004 Report No CE941006H04B 69 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP HARMONICS EMISSION TEST amp VOLTAGE FLUCTUATIONS AND FLICKER TEST Mode 1 941219904 HARMONICS EMISSION TEST 8 VOLTAGE FLUCTUATIONS AND FLICKER TEST Mode 2 941219H04 Report No CE941006H04B 70 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP ESD TEST Mode 1 ESD TEST Mode 2 Report No CE941006H04B 71 Report Format Version 2 0 4 Reference No 941219H04 CORP RS TEST
53. the performance as described in criteria A is CRITERION B permitted provided that the normal operation of the EUT is self recoverable to the condition immediately before the application of the test In these cases operator response is permitted to re initiate an operation Degradation of the performance as described in criteria A and B is permitted provided that the normal operation of the EUT is CRITERION C self recoverable to the condition immediately before the application of the test or can be restored after the test by the operator 5 3 1 EUT OPERATING CONDITIONS Same as the 4 1 6 Report No CE941006H04B 41 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 4 ELECTROSTATIC DISCHARGE IMMUNITY TEST ESD 5 4 1 TEST SPECIFICATION Basic Standard IEC 61000 4 2 Discharge Impedance 330 ohm 150 pF Discharge Voltage Air Discharge 2 4 8 kV Direct Contact Discharge 2 4 kV Indirect Polarity Positive Negative Number of Discharge Air Discharge min 20 times at each test point Contact Discharge min 50 times at each test point Discharge Mode Single Discharge Discharge Period 1 second minimum 5 4 2 TEST INSTRUMENTS DESCRIPTION amp MANUFACTURER MODEL NO SERIAL NO CALIBRATED UNTIL Key Tek ESD Simulator MZ 15 EC 9906323 Feb 20 2006 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST
54. uipment shall be subjected to the test magnetic field by using the induction coil of standard dimension diameter 1 5m The EUT placement shall then be rotated by 90 degrees in order to expose to the test field with different orientations Report No CE941006H04B 61 Report Format Version 2 0 4 Reference No 941219H04 CORP 5 9 5 TEST RESULTS 1 2 Internet Phone MODEL PAP2T Adapter TEST MODE Mode 1 2 INPUT POWER 230Vac 50 Hz ENVIRONMENTAL 16 deg 44 CONDITIONS 974 hPa TESTED BY Miten den DIRECTION RESULTS OBSERVATION PERFORMANCE CRITERION O PASS Y PAS Nte PASS NOTE There was no change compared with the initial operation during the test Report No CE941006H04B 62 Report Format Version 2 0 4 Reference No 941219H04 ADT CORP 5 10 VOLTAGE DIP SHORT INTERRUPTIONS VOLTAGE VARIATIONS DIP IMMUNITY TEST 5 10 1 TEST SPECIFICATION Basic Standard IEC 61000 4 11 Test Duration Time Minimum three test events in sequence Interval between Event Minimum ten seconds Phase Angle degree 0 90 180 270 Test Cycle 3 times 5 10 2 TEST INSTRUMENTS DESCRIPTION amp MODEL NO SERIAL NO CALIBRATED UNTIL EMS Simulator Simulator EMC Pro 9712339 Feb 22 2006 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC
Download Pdf Manuals
Related Search