Home

Software Quick Start Guide Manual

1. Is the Mass Storage Driver running B amp Intel 92371SB PCI to USB Univd E USB Mass Storage amp USB Root Hub Double click System in the Control Panel select the Device Manager tab and check the Mass Storage Driver If the driver is marked with a yellow or a red x Mass Storage Driver is not running Uninstall and then re install Mass Storage Driver see P 16 49 If you are using Windows 2000 Professional are you logged on as an Administrator group Log on as an Administrator group Refer to the User s Manual for your PC for more information on Administrators E The PC hangs when access the SmartMedia Possible cause Solution When opening the Device Manager there is a yellow mark next to the driver in Universal Serial Bus controllers You are using a driver or camera that prevents the driver for the Universal Serial Bus controllers from operating Refer to the User s Manual for your PC and check your hardware and software setup When opening the Device Manager there is a yellow mark next to Mass Storage Driver You are using a driver or camera that prevents the Mass Storage Driver from operating Uninstall and then re install Mass Storage Driver see P 16 49 Gems ineen neimen Pt etenas amp USB Mass Storage Driver software installed Is an older version o
2. Thumbnail When you double click a thumbnail the image is displayed in a new image window To close the image window click the Close box in the top left corner of the window You can copy an image and save it to the hard disk of your PC by dragging its thumbnail and dropping it onto the desktop or into a folder To Disconnect the Camera 1 To exit FinePixViewer select Quit from the File menu or click the Close box in the main window 2 Drag the Removable disk icon on the desktop to the Trash Alternatively select the icon and then select Eject from the Special menu in the menu bar along the top of the screen 3 When a message appears indicating that it is OK to remove the card or cable from the camera disconnect the camera Switching off the camera or removing the SmartMedia without using the eject procedure described above could damage the SmartMedia or cause your Macintosh to malfunction Macintosh Attaching Images to E mail Messages in FinePixViewer FinePixViewer provides a simple procedure for attaching images to an e mail message This feature can only be used when Outlook Express is selected as your default e mail application Contact your ISP Internet Service Provider for information on setting up Outlook Express E Check the following Check that Outlook Express is registered as your default e mail application o Internet i Active Set untitied v ta
3. 1 Drag the 100 FUJI folder from the folder tree display area and 74 FinePixViewer 100_FUJI File Edit View Go Bookmarks Settings Videt es oe S E drop it into the My Documents aa S308 2 folder H A My Documents EAS My Computer a 3 Floppy A x Copying begins Local Disk C HQ 0 B Removable Disk E 4 pcm amom 2 When copying is completed 22 FinePinviewer 100_Fu double click My Documents to File Edit View Go Bookmarks Settings Videt open the folder and then click the SEKRO 100_FUJI folder inside My Documents T Documents Sih Las My Computer 31 Floppy 4 5 6 Local Disk C 3 Click the 100_FUuI folder again 3 H 0 and rename it Removable Disk E B a DECIM LJ 100_FUJI TIP Including the date in the name can make it easier to identify the folder later NOTE Do not rename folders on the SmartMedia as this could make it impossible to play back the images on the camera e If there is already a folder with the same name in the My Documents folder a message appears saying The folder with the same name as XXXXXX already exists Overwrite If this occurs click the Rename button and rename the folder before copying warni xl The folder with the same name as 100_FUJI already exists Overwrite 5 Cancel Skip i ee Checking saved images on your P
4. button Add New Hardware Wizard What do you rani Windorrs to do Reames Hina eitri i e iver you What do you want Windows to do Search for the best driver for your devi Recommended nn a Black Conca 8 When the next window opens tick the CD ROM drive checkbox and then click the Next gt button If any checkboxes other than CD Add New Hardware Wizard ROM drive are ticked clear the ticks so that CD ROM drive is the Windas val search lor new divers in te diner dababace following selected on your hed dive and in any of the locations Click Next to start the search only checkbox ticked I Bloppy disk dives r I Specily a location I E T Floppy disk drives Back Cancel The dialog shown may differ slightly on some types of PC 23 9 Check that VC4CB104 INF Add New Hardware Wizard has been detected and then WEE EINE click the Next gt button The Windows 98 CD ROM may also be required during installation In this event switch CD ROMs as directed by the on screen instructions USB PC Camera TOR ATON SOHN MANARE to contie Location of divar Se EAVCACBIOAINF 10 When driver installation is Ada How HatONU WICEN completed the dialog shown a hiiia at right is appears Click the Finish button 11 FinePixViewer starts up and the PictureHello window automatically opens Check that the live video i
5. 3 Place a tick in the File Format Conversion checkbox and select the format compression ratio for converted files TIP To prevent image resizing remove the tick from the Resize and File Format Conversion checkboxes 34 Windows Using the FinePix Internet Service If you use the FinePixViewer you can also access the FinePix Internet Service via the Internet When you register you will be able to use the various services provided in the country where you are registered The services provided vary depending on the country e The services are frequently updated so we recommend that you access them regularly In order to access the service you need to have an internet connection provided by an ISP Internet Service Provider x You must have the hardware and software required for connecting to the Internet The FinePix Internet Service does not include any connection fees charged by your service provider or the normal telephone charges for dialing your service provider s access number User Registration To use the FinePix Internet services users must first register Follow the steps below to register Users can be registered for free 1 Select Programs FinePixViewer FinePixViewer in the Start menu to launch FinePixViewer 2 Click the User s Registration button The operation selection dialog box appears lt User s Reg
6. e In addition to MPEG you can choose from a wide range of formats for saved files Capturing Live Images If you are using a camera with the PC Camera function in the USB settings you can import live images from the camera It is strongly recommended that you connect the AC power adapter when you are using a USB connection to avoid loss of power while you are using the camera Refer to PC Connection in the Owner s Manual for your camera for more information on camera operation and the USB settings 1 Select PC Camera in the camera s USB settings 2 Using the special USB cable connect the camera cradle to the USB port on your computer and then switch the camera on If you have launched FinePixViewer exit the program 3 Double click the Videolmpression icon in the folder in which Videolmpression was installed 4 When the startup screen appears click the new button ms video _ Impression 5 When the album window opens click the capture button 79 6 The Capture window appears and the live image is displayed Recording has not yet started 7 Click the Capture Video button to begin recording the movie t The name of the button changes to Stop Capture During recording only the Stop Capture button can be pressed lt Standby gt lt Movie recording in progress gt Video Setting Stop Live J Video Setting Stop Live Vid
7. not listed under Other Devices in the Device Manager The driver is not installed correctly Uninstall see P 49 and then re install driver Are the USB functions active Double click System in the Control Panel select Device Manager and check Universal Serial Bus controllers e If Universal Serial Bus controllers is not displayed the USB functions is disabled Refer to the User s Manuals supplied with your PC for details of how to enable the USB functions e USB functions are disabled when the item is marked with a yellow exclamation mark or red cross x Refer to the User s Manuals supplied with your PC for details of how to enable the USB functions Universal Serial Bus controllers ED Intel 82371SB PCI to USB Universal Host Controller amp USB Root Hub Is an older version of the PC Camera Driver installed Use the CD ROM provided to uninstall any older versions of the PC Camera Driver Then install the new PC Camera Driver provided on the CD ROM 53 E was asked for a disk labeled FINEPIX during Mass Storage Driver installation Solution Click the Browse button in the Copy files dialog box ln the dialog box that then appears select the CD ROM icon in the drive display area refer to the information in the table below and specify the appropriate folder and then click the OK button ln th
8. save destination and click the OK button 2 When the album storage confirmation dialog box appears click the OK button e You must have a sound card installed and speakers and a microphone connected to your PC to input and output sound The time required for playing and saving images varies depending on the performance of your PC Do not perform any of the following while live camera images are being displayed as this could cause your PC to freeze see P 62 Switch off the camera Touch any of the control buttons on the camera Disconnect the USB cable Remove the SmartMedia Open the SmartMedia cover Remove the camera battery Remove the camera from the cradle For Mass Storage Driver Open My Computer right click the CD ROM icon and select Open to display the contents of the CD ROM Double click UNIN_MAS EXE to remove the installed driver For PC Camera Driver Open My Computer right click the CD ROM icon and select Open to display the contents of the CD ROM Double click UNIN_PCC EXE to remove the installed driver The way file names are displayed differs as described below depending on your computer settings e File extensions 3 letter suffixes indicating the file type may be shown or hidden e Text may be shown normally or all in uppercase e g Setup or SETUP Reboot your PC to complete the uninstallation process Uninstalling FinePixViewer DP
9. 24 S0 hide aac ed etree Sea es hae oS Customizing the Camera 00 c eects Using Videolmpression 0 0 0 0 0000 c cece eee Uninstalling the Software on a Macintosh Uninstalling Mass Storage Driver and PC Camera Driver 81 Uninstalling Exif Launcher FinePixViewer and DP Editor 81 Troubleshooting eeeeeeseeeeseneneeeeeeenseeeeeneneeesseeeeaseeeeeneneeeneeeneaseeees 82 Symbols Used in This Guide The symbols listed below are used throughout this guide Indicates important precautions to follow when using the software Indicates important information t Indicates notes or additional information Indicates useful tips Introduction Glossary of Terms This section provides explanations of the minimum basic operations you must be familiar with in order to use your personal computer along with an introduction to some other operations that will help you to use your computer more efficiently For more detailed information on using your computer refer to the user manuals supplied with the computer Application software Software used for a specific purpose such as word processing spreadsheets or image editing E Browser Software used for viewing web pages on the Internet Examples include Internet Explorer and Netscape Navigator E Click Double click Click Pressing the left mouse button Windows or the mouse button Macintosh once and then releasing it Used to select f
10. D Windows Troubleshooting Connection and Image Viewing Problems E When I connect the camera to my PC the Add New Hardware Wizard appears Possible cause Is the USB Driver installed Solution Use the enclosed CD ROM to install the driver See P 16 22 E When double click the removable disk icon The device is not ready error message appears Possible cause Is the SmartMedia loaded in the camera Solution Load a SmartMedia into the camera Refer to the Owner s Manual for your camera for details E A warning message appeared when I removed the SmartMedia from the camera Possible cause Did you eject the SmartMedia while data access to the camera was still in progress Solution This action can damage the SmartMedia and destroy data on the SmartMedia Always close all the files on the camera the removable disk and wait until the camera display indicates that data access is no longer in progress before removing the SmartMedia Device disconnection warning appears when disconnect the special USB cable Possible cause Solution Are you using Windows 2000 Before disconnecting the special USB Professional or Windows Me cable click the Eject icon in the Taskbar and disconnect the camera 55 E When disconnect the special USB cable and double click the removable disk icon a message appears an
11. Driver active Enable USBO4CB_StorageShim and USBO4CB_StorageDriver in the Extensions Manager and restart your Macintosh E A warning message appears when I remove the SmartMedia or disconnect the USB cable from the camera Possible cause Solution Did you eject the SmartMedia or This action can damage the SmartMedia disconnect the USB cable while the and destroy data on the SmartMedia camera was still mounted as a disk Before ejecting the SmartMedia or drive disconnecting the USB cable always select the drive and then choose Eject from the Special menu Alternatively you can drag the drive icon to the Trash 83 Troubleshooting Internet Problems E can t log in to the FinePix Internet Service Possible cause Solution Are you able to connect to the Check your PC hardware and software Internet setup Is the FinePix Internet Service Log in after the maintenance is undergoing maintenance completed Click the FinePixViewer user registration button and sign on as a FinePix Internet Service user See P 73 Have you completed the user registration process E can t sign on as a FinePix Internet Service user Possible cause Solution Have you already signed on under the You cannot sign on twice with the same same e mail address user ID or e mail address E can t update the Internet menu properly The bu
12. PC Connection in the Owner s Manual for your camera for details Is the special USB cable connected to the camera cradle and to the computer Are you using a compatible operating system Check that one end of the special USB cable is connected to the camera cradle and the other end is connected to the computer The Mass Storage Driver should be used with Windows 98 98SE Windows Me or Windows 2000 Professional If you are using Windows 2000 Professional are you logged on as an Administrator group Log on as an Administrator group Refer to the User s Manual for your PC for more information on Administrators Is USB Mass Storage not listed under Other Devices in the Device Manager The driver is not installed correctly Uninstall see P 49 and then re install driver Are the USB functions active Double click System in the Control Panel select Device Manager and check Universal Serial Bus controllers Tag Universal Serial Bus controllers ED Intel 82371SB PCI to USB Universal Host Controller amp USB Root Hub If Universal Serial Bus controllers is not displayed the USB functions is disabled Refer to the User s Manuals supplied with your PC for details of how to enable the USB functions e USB functions are disabled when the item is marked with a yellow exclamation mark or red cross x Refer to the User s Manuals supplied
13. Service user registration and store the other party s e mail address in your PictureHello address book see P 43 2 Select PC Camera in the camera s USB settings Use the special USB cable to connect the camera to the USB port on your PC and then switch the camera on Check that FinePixViewer has started up and the PictureHello window has opened automatically To open the PictureHello window manually select Open Window from the Videoconference menu in FinePixViewer If a video input device other than the camera is connected to your PC disconnect the video input device and then reconnect the camera You cannot use PictureHello and NetMeeting concurrently If you are using PictureHello do not launch NetMeeting Refer to PC Connection in the Owner s Manual for your camera for more information on camera operation and the USB settings Do not switch off the camera or disconnect the USB cable during live image display as this may cause your PC to hang e It is strongly recommended that you connect the AC power adapter during videoconferencing to prevent the camera from switching off e If the PictureHello window does not open check the following 1 Is PC Camera selected in the USB settings on the camera 2 Is the USB cable connected correctly If the problem is not caused by either of these refer to Troubleshooting P 59 e If no live image is displayed right click in the
14. buttons do not line up correctly Solution Quit FinePixViewer the FinePixViewer icon in the FinePix was installed The menu data is corrupted Use the procedure below to update the menu From the Start menu select FinePixViewer in Programs Then right click on Click the Find link destination button to display the folder in which FinePixViewer Delete the FinePixinternetFiles folder in the FinePixViewer installation folder Launch FinePixViewer and click the Update button Viewer folder and select Properties Installation on a Macintosh Pre installation Checklist E Hardware and software requirements To run this software you must have the hardware and software described below Check your system before you begin the installation Compatible Mac Power Macintosh G3 1 PowerBook G3 1 Power Macintosh G4 iMac iBook Power Macintosh G4 Cube or PowerBook G4 Operating System Mac OS 8 6 to 9 1 RAM 64 MB minimum 2 Display 800 x 600 pixels or better at least 32 000 colors Hard disk space Amount required for installation 70 MB minimum Amount required for operation 300 MB minimum Supported cameras Fujifilm digital cameras equipped with a USB interface Internet connection 3 56 kbps modem connection recommended or better or an ISDN connection Sound functions 4 Speakers microphone and sound card 1 Models with a USB port as a standa
15. conditions of the license granted for you to use the software provided by Fuji The CD ROM contains third party software In case a separate agreement is provided by a third party supplier for its software the provisions of such separate agreement shall apply to the use of such third party software prevailing over those of this Agreement 1 Definitions a Media means the CD ROM titled Software for FinePix EX which is provided to you together with this Agreement b Software means the software which is recorded on Media c Documentation means the operation manuals of Software and other related written materials which are provided to you together with Media d Product means Media including Software and Documentation collectively Use of Software Fuji grants to you a nontransferable nonexclusive license a to install one copy of Software onto one computer in binary machine executable form b to use Software on the computer onto which Software is installed and c to make one backup copy of Software Restrictions 3 1 You shall not distribute rent lease or otherwise transfer all or any part of Software Media or Documentation to any third party without Fuji s prior written consent You also shall not sublicense assign or otherwise transfer all or any part of the rights granted to you by Fuji under this Agreement without Fuji s prior written consent 3 2 Except as expressly granted by Fuji
16. images video and sound you first have to import them into the album window 1 Double click the Videolmpression in the folder in which Videolmpression was installed to launch Videolmpression 2 Click the new button to open an album window 3 Drag the thumbnails from FinePixViewer and drop them into the album window lt FinePixViewer gt 77 78 E Add a storyboard In the storyboard you select the files to be used in the movie and set the order in which the files are played Drop images into here a Drop sounds fi into here 1 Add files to the movie by dragging them from the album window and dropping them onto the storyboard 2 If necessary you can drag items around in the storyboard to change the playback sequence E Add text 1 Click the edit movie button to switch to the editing window 2 Click the text button and enter the text 1 You can use the drag handle to adjust the position 3 Use the buttons below the image to specify settings such as the typeface and the time for which the text appears E Play back the movie 1 Click the play movie button to switch to the playback window 2 Click the Play button and check the movie Macintosh TIP e If you leave the mouse pointer positioned over a button or image for a few seconds information about that button or image is displayed e In any window you can access the online help by clicking
17. in to the FinePix Internet Service can t sign on as a FinePix Internet Service user can t update the Internet menu properly The buttons do not line up correctly 84 Internet The FinePixViewer Upload dialog box does not appear The Process aborted because error occurred during communication message appears while you are using the FinePixViewer Upload dialog box Live images do not appear in the Videolmpression Capture window My camera will no longer play back image files 85 want to stop the FinePixViewer from launching automatically Troubleshooting Connection and Image Viewing Problems E When I connected the camera to my PC the Required software not found message or Required driver cannot be used message appears f The software needed to use the USB device USB Mass Drivers needed for the USB device USB PC Storage cannot be found Please refer to the device H Camera are not available Would you like to look documentation to install the necessary software for these drivers over the Internet Coma CJ Possible cause Solution Is the software installed Install the software on your PC Macintosh E When I connected the USB cable Mac OS displayed the Initialize disk message Possible cause Solution Is the SmartMedia formatted Disconnect the USB cable from the camera insert the Smart
18. it in the DSCSETUP folder in the FinePixViewer folder on your Macintosh computer http home fujifilm com products digital 2 When you click the camera customization button on the FinePixViewer the customization software starts up and the settings dialog box appears Refer to the downloading web page for information on installing the customization software Refer to PC Connection in the Owner s Manual for your camera for more information on transferring data from your PC to the camera 76 Macintosh Using Videolmpression You can use Videolmpression to make your own movies For more information on Videolmpression refer to the contact information provided on the back cover of this manual Main Functions Allows you to create and save movies that include both still and moving images and sound Allows you to edit your movies so you can cut unwanted scenes or add captions e Provides effective ways of switching from one scene to another transitions More information on these functions and how to use them is available as follows Open the English pdf file in the Manual folder inside Vimpress on the enclosed CD ROM e Check on the Internet by clicking the link in the bottom right corner of the screen Use the contact details printed on the back cover to contact FUJIFILM Making Your Own Movies E Store the movie in an album To work with still
19. not show video of me 58 59 clicked the Login button in PictureHello videoconferencing but can t log in The live image of the other party in videoconferencing is very jerky There is no live image of the other party during videoconferencing Videoconferencing call notifications are not displayed 60 can make calls but cannot use videoconferencing can t hear the other party in the videoconference The other party can t hear me Live images do not appear in the Videolmpression Capture window 61 62 can t log in to the FinePix Internet Service I can t sign on as a FinePix Internet Service user My PC does not shut down correctly Other My camera will no longer play back image files can t play AVI files on Windows Media Player can t update the Internet menu properly The buttons do not line up correctly 63 Troubleshooting Installation Problems E The camera is connected to my PC but the Mass Storage Driver installation will not start Possible cause Solution Is the camera cradle switched on Switch the camera on If you are using the cradle connect the AC power adapter to the cradle and press the button Refer to the Owner s Manual for your camera for details Is DSC selected as the camera s USB setting Change the camera s USB setting to DSC Refer to
20. service provider s web site or an upload dialog box may open The actual Internet menu may differ slightly in appearance from the sample shown here TIP Move the mouse cursor over an Internet menu button to view information about the service 2 When you have finished using the Internet services disconnect from the Internet for dial up connections The connection speed will vary significantly depending on the quality of your phone line and the amount of traffic on the server to which you are connected E Updating the Menu 1 Select Menu Update from the View menu 2 The User Verification dialog box appears Enter the user ID and password set during user registration and then click the OK button to update the Internet menu Enter Network Password User ID fujifilm Password ex f you are not already connected to the Internet the software automatically attempts to connect for dial up connections TIP As well as the Internet menu being updated related information pages may also be opened Because these pages may contain good news or useful information you should update the Internet menu frequently 75 Customizing the Camera Cameras with a customization function can be customized using special customization software downloaded from the FinePix Internet Service 1 Download the special customization software from the FinePix Internet Service or from the following web site and install
21. B a warning message appears when you click Mail Sending If this occurs reduce the number or size of the images until the message no longer appears Open Ctrl O Delete Mail Sending Automatic Save Automatic Rename Batch Resize Batch Rotation Information Batch Edit The Outlook Express or Wf New Message Outlook2000 mail transmission Eile Edit view Insert Format I window opens and the images are 3 amp Ae Gut Copy Paste Und automatically attached to your e mail message Type in the To address title and your message ace Subject and then send the message in the usual way Attach E7 D5cF0004 3PG 260 KB Do not quit FinePixViewer until mail transmission is complete as this will prevent the e mail with the images attached from being sent 33 E Setting the file size for attached images When FinePixViewer attaches an image file to an e mail message it adjusts the size of the image file in accordance with the Mail Transmission Settings The file size is preset to an appropriate size for e mailing immediately following installation but this setting can also be revised When an image is resized the original image is not affected 1 Click Mail Transmission Settings in the Settings menu 2 Place a tick in the Resize a zi checkbox and specify the pe number of pixels height and Pressed Me width for resized images eg
22. C 1 When you click the folder you copied to the folder tree display area thumbnail versions of the images in the folder are displayed 2 If you then double click one of the thumbnail images the image appears in its own image window Click the EJ Close button in the top right corner of the window to close the image window Windows To Disconnect the Camera 1 To exit FinePixViewer select Exit from the File menu or click the Close button in the main window 2 Check that the camera display indicates that data access is no longer in progress On Windows 2000 Professional and Windows Me click the eject icon on the taskbar when the camera display indicates that data access is no longer in progress and remove USB Mass Storage or USB Disk 3 Switch the camera off and then disconnect it e You must first close all the camera removable disk files and check that the camera access indicator is no longer lit e When the Copying message disappears from your PC screen wait a few moments before removing the camera from the cradle disconnecting the USB cable or removing the SmartMedia If a large amount of data is being copied camera access continues for a short time after the message displayed on the PC has gone off e Refer to the Owner s Manual for your camera for more information on the access display on the camera e In Windows 2000 Professional or Windows Me yo
23. E Selected Set My Settings s F Energy Saver EJ File Exchange E File Sharing Duplicate Set D Show Item Information z amp iE E E The following applications and USB driver are installed by the Installer USB driver FinePixViewer DP Editor Exif Launcher Videolmpression QuickTime Acrobat Reader x When you install the USB driver the following files are installed in the Extensions folder USBO4CB_StorageShim USBO4CB_StorageDriver USBO4CB_VcShim and USB04CB_VcDriver Installation Procedure 1 When you load the enclosed CD ROM into the CD ROM drive the FinePix window automatically opens and the Installer appears If the FinePix window does not open automatically double click the CD ROM icon O FinePix E B a 6 items 51 3 MB ava a A l Installer ha 2 Double click Installer to launch the Installer 3 The Installer setup screen appears Click the Install FinePixViewer button FUJIFILM FinePixViewer Click to select an installation option ED Install FinePixViewer Ra Install Acrobat Reader v 4 A list of the applications to be installed appears Check the list and then click the OK button Installing the following After they are installed Macintosh will be restarted USB Driver e FinePixViewer DP Editor Exif Launc
24. Editor and Exif Launcher You can automatically uninstall these application programs using Add Remove Programs in the Control Panel Use this procedure only when the installed software is no longer required or when software installation fails Always quit FinePixViewer DP Editor and Exif Launcher before beginning uninstallation For information on shutting down Exif Launcher refer to the lower half of P 29 Uninstall Exif Launcher before uninstalling FinePixViewer Connecting the camera to your PC with only Exif Launcher left installed could cause problems Switch on your PC and start up Windows Open the My Computer window and double click Add Remove Programs in the Control Panel Select the application to be uninstalled The Add Remove Programs Properties window appears Select the program to be deleted FinePixViewer Exif Launcher or DP Editor and click the Add Remove button Confirm the deletion A confirmation dialog box appears Uninstallation cannot be cancelled once it has been confirmed in this dialog box Check the details carefully UninstallShield starts up When uninstallation ends click the OK button Windows Troubleshooting If the software does not operate correctly but the problem does not match any of those listed below check that you are using the correct hardware and software See P 10 If the problem persists even though you are using the correct hardware
25. FinePix Internet Service and videoconferencing The software can still be installed even if you do not have an Internet connection 3 Cameras that feature the PC Camera option in the USB settings allow you to use the videoconferencing functions and the Videolmpression capture function Sound functions are required for audio input output in Videolmpression and videoconferencing e Connect the camera cradle directly to the computer using the special USB cable The software may not operate correctly if you use an extension cable or connect the camera cradle via a USB hub If your computer has more than one USB port the camera can be connected to either port e Push the USB connector fully into the socket to ensure that it is securely connected The software may not operate correctly if the connection is faulty e Additional USB interface board is not guaranteed e Windows 95 cannot be used e Operation is not guaranteed on home built computers or on computers running updated operating system software e Use the drivers the Mass Storage Driver and PC Camera Driver provided on the enclosed CD ROM When older drivers are already installed on your PC uninstall the old versions and then re install the drivers provided on the enclosed CD ROM e If your Internet connection is via a router or via a LAN connecting machines on the LAN to the Internet you cannot use videoconferencing in conjunction with these instructions Switch o
26. Media into the camera and format the SmartMedia Refer to the Owner s Manual for your camera for details Enable File Exchange See P 65 for details Use a different SmartMedia t SmartMedia of this size are not recognized by File Exchange and cannot be used with a Mac OS E The PC hangs when access the SmartMedia Possible cause Solution Is the software installed Install the software on your PC E The camera and PC are connected but no removable disk icon is displayed Possible cause Solution Is the camera cradle switched on Switch the camera on If you are using the cradle connect the AC power adapter to the cradle and press the 6 button Refer to the Owner s Manual for your camera for details Is the SmartMedia loaded in the Load a SmartMedia into the camera camera Refer to the Owner s Manual for your camera for details Is DSC selected as the camera s USB Change the camera s USB setting to setting DSC Refer to PC Connection in the Owner s Manual for your camera for details Is the special USB cable connected to Check that one end of the special USB the camera cradle and to the cable is connected to the camera cradle computer and the other end is connected to the computer Are you using a compatible operating The USB Driver should be used with Mac system OS 8 6 to 9 1 It is not compatible with Mac OS X Is the Mass Storage
27. RASPENA nia To nat ha saue a ia nage ag ROM hive nl Opona sesch locahons Dee cc 12 FinePixViewer starts up and the PictureHello window ne jae eC 3 automatically opens Check that the live video image is 1 rives Dp 9 s eo eee aa E displayed in the PictureHello window If live images are not displayed installation was not completed successfully The screen shown may differ slightly depending on the type of computer Refer to Troubleshooting P 59 26 27 28 Using the Software on Windows Connecting the Camera and PC and Viewing Images Have the Owner s Manual for your camera handy and read it in conjunction with these instructions To View Images Using FinePixViewer TIP For detailed information on using the FinePixViewer and DP Editor refer to English pdf in FinePixViewer in Programs in the Start menu Do not perform the operations listed below when a camera removable disk file is open and the camera display indicates that data access is in progress Performing any of these operations could corrupt the data on the SmartMedia or damage the SmartMedia itself Switch the camera off Touch any of the camera control buttons Disconnect the USB cable Remove the SmartMedia Open the SmartMedia cover Remove the camera batteries Remove the camera from the cradle Do not use your computer to format the SmartMedia in the camera as this ma
28. SB Mass Storage is detected e If the dialog box does not appear uninstall and then re install the Mass Storage Driver See P 16 49 8 Select USB Mass Storage on the same line as A USBDRV WINME UFLT04C B INF on the CD ROM and then click the OK button The Windows Me CD ROM may also be required during installation In this event switch CD ROMs as directed by the on screen instructions 9 When you click the Finish button the New Hardware dialog box appears Wait until the dialog box disappears 10 Installation is completed when a new removable drive icon the connected camera appears in the My Computer window Add New Hardware Wizard Windorre hss bound the following new harden USB Mats Storage Windows can automatically search for ard install software that supports your hardware If your hardware came with wdallabon media nett ron and dick Need What would you like to do Bunce snatch for a bones deves Recommended Specly the locaton of the diner ubvanced peo eae aoa Select Other Driver x Windows han lound more han one driver that may woad for your hardware Please select the diver that matches you language and device Lee Deserte T osre puie gt 1135300 Check the file name Click here Coe eu Add New Hardware Wizard rad USB Mass Storage Windows hiss breched instalirg thre zofirrare you selected th
29. TY EXPRESS IMPLIED OR STATUTORY AS TO ANY OTHER MATTERS INCLUDING BUT NOT LIMITED TO NON INFRINGEMENT OF ANY COPYRIGHT PATENT TRADE SECRET OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY MARCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE 7 LIMITATION OF LIABILITY IN NO EVENT SHALL FUJI HAVE ANY LIABILITY FOR ANY GENERAL SPECIAL DIRECT INDIRECT CONSEQUENTIAL INCIDENTAL OR OTHER DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFITS OR LOST SAVINGS INCURRED FROM THE USE OF OR INABILITY TO USE PRODUCT EVEN IF FUJI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 8 No export You acknowledge that neither Software nor any part thereof will be transferred or exported to any country or used in any manner in violation of any export control laws and regulations to which Software is subject 9 Termination In case you breach any of the terms and conditions hereof Fuji may immediately terminate this Agreement without any notice 10 Term This Agreement is effective until the date when you cease to use Software unless earlier terminated in accordance with Section 9 hereof 11 Obligation upon termination Upon termination or expiration of this Agreement you shall at your own responsibility and expense delete or destroy immediately all Software including its copies Media and Documentation 12 Governing Law This Agreement shall be governed by and construed in accordance with laws of Japan Do not attempt to play t
30. The User s Guide PDF and How to Read It To read the FinePixViewer User s Guide PDF you must have Adobe Systems Acrobat Reader installed on your computer See P 67 for information on installing Acrobat Reader E Reading the User s Guide 1 Double click English pdf in the folder in which FinePixViewer was installed Acrobat Reader starts up and displays the User s Guide 2 To jump to the relevant page click the desired topic listed in the Contents or Bookmarks To view the bookmarks click Show Bookmarks in the Window menu For more information on how to use Acrobat Reader refer to the Online Guide in the Acrobat Reader Help menu E Printing the User s Guide 1 Click Page Setup in the File menu and specify the required settings Paper Layout etc es f you print the manual at the original dimensions each page fits on one sheet of A4 paper in Portrait layout 2 Click the Print button or select Print in the File menu 3 Specify the range of pages to be printed and the number of copies etc and then click the OK button The available options vary depending on your printer and printer driver software Refer to your printer driver manual for details For more information refer to the Online Guide in the Acrobat Reader Help menu Macintosh Using the Software on a Macintosh Connecting the Camera and Macintosh and Viewing Images Have the Owner s M
31. The Windows CD ROM may also be required in some cases Have the CD ROM ready beforehand 1 Switch on your PC and start up Windows 2 Double click the My Computer icon When installation is completed a new removable disk icon the connected camera 3 is added 3 Insert the enclosed CD ROM into the CD ROM drive If the installation screen for the applications provided on the CD ROM appears click the Exit button to exit the screen 4 Select the camera settings If your camera has DSC Mass Storage and PC Camera functions in the USB setting such as FinePix6800 ZOOM Load a SmartMedia containing images you have shot into the camera Select DSC in the camera s USB setting If your camera has only the DSC Mass Storage function in the USB setting Load a SmartMedia containing images you have shot into the camera e Refer to PC Connection in the Owner s Manual for your camera for more information on camera operation and the USB setting e Use only SmartMedia containing images shot on a FUJIFILM digital camera It is strongly recommended that you connect the AC power adapter when you are using a USB connection to avoid loss of power while you are using the camera 5 Using the enclosed USB cable connect the camera or the cradle to the USB port on your computer and then switch the camera on 6 A message appears in the New Hardware d
32. a to be used as Allows a digital camera to be used USB Mass Storage removable disk as a PC Camera Some cameras drive do not support this function Videolmpression Launches the FinePixViewer i Used to download and edit Exif Launcher software when a camera is connected movies you have shot FinePixViewer Allows you to display thumbnail lists of the images stored on your PC or in the camera print the images individually or as an index display the images at full size and perform some basic image processing PictureHello Used for videoconferencing Windows only You can use this software to generate the information you will need to print your images using a printer that supports DPOF Digital Print Order Format QuickTime DP Editor Software needed for playing back movies etc Software used to read PDF format documents on a Acrobat Reader personal computer This software is needed to read the User s Guides for FinePixViewer and Videolmpression FinePix Internet Service Users can sign up to get access to a wide range of services To sign on as a user refer to the following pages Windows users P 35 Macintosh users P 73 Transmission Via the Internet Taking Part in a Videoconference FinePixViewer PictureHello Requirements e A FUJIFILM camera that has the PC Camera function e A connection to the Internet e A Windows PC with a sound card and a microphone and speaker
33. ae fox the fclloweng device 4 USB Mass Storage Windows found a driver for thir device To install the diver Windows found click Next D outono TRANSA AAA TS AE el ee To witws a iat ot 3 of enitall one a hese drames select thn folowang chock box ard then chek nee FF Intal one of the other divers lt Back Cancel Found New Hardware Wizard Completing the Found New Hardware Wizard USD Mate Storage Windows hat trashed neti the scltraee ka thes device T the vaoaed cick Fi a alaini Che ia ye rss ph ye ero ot herd m Gren O XO agren hea z ee g 3 gt x My Computer nm e bon _ z 4 J in corer 21 Installing the PC Camera Driver If your camera has a PC Camera function in the USB setting installing PC Camera Driver allows you to import live images from the camera Use PictureHello see P 38 or Videolmpression see P 45 to actually view live images Here live images refers to the video images shown on the LCD monitor when the camera is set to photography mode If you use a camera that does not have the PC Camera function in the USB settings live images cannot be transmitted The Windows CD ROM may also be required in some cases Have the CD ROM ready beforehand 1 Switch on your PC and start up Windows Do not connect other video capture equipment to your PC 2 Insert the enclosed CD ROM into the CD ROM drive If the installation scr
34. ager and check USB PC Camera in Imaging or Other Devices If USB PC Camera is marked with a yellow exclamation mark or ared cross x it is not running Uninstall and then re install PC Camera Driver see P 22 49 E PictureHello videoconferencing does not show video of me Possible cause Solution Is another video input device connected to your PC Disconnect all other video input devices Is another application displaying the live images from the camera Quit any other application that is displaying live images Did you disconnect the special USB cable or switch off the camera cradle during live image display Quit PictureHello and then restart your PC Check that the special USB cable is connected correctly to the camera and your PC and then switch the camera cradle on E clicked the Login button in PictureHello videoconferencing but can t log in Possible cause Solution Are you able to connect to the Internet Check your PC hardware and software setup Is the FinePix Internet Service undergoing maintenance Log in after the maintenance is completed Have you completed the user registration process Sign on as a FinePix Internet Service user See P 35 E The live image of the other party in videoconferencing is very jerky Solution Use a high speed line with a connection speed
35. alog box appears Enter the user ID and password set during user registration and then click the OK button to update the Internet menu Enter Network Password x a User ID fujifilm Password N Cancel ex f you are not already connected to the Internet the software automatically attempts to connect for dial up connections TIP As well as the Internet menu being updated related information pages may also be opened Because these pages may contain good news or useful information you should update the Internet menu frequently 37 38 Videoconferencing Using PictureHello E What is videoconferencing Videoconferencing is a form of communication in which you can see a live image of the person you are calling as you converse in realtime This explanation describes the use of the FinePixViewer PictureHello software in which specific PCs communicate with each other one to one communication via the Internet E Hardware and software required for videoconferencing A FUJIFILM camera equipped with the PC Camera function A PC with an Internet connection yx 56kbps modem connection or better or an ISDN connection yx An established service contract with an Internet service provider ISP Depending on your type of Internet connection and or your modem connection speed video quality may deteriorate and some frames may be lost yx A sound card installed and speakers and a microphone connected to your PC PCs
36. and software refer to the table below and then see the reference page listed for your problem Page The camera is connected to my PC but the Mass Storage Driver installation will not start 52 The camera is connected to my PC but the PC Camera Driver installation will not start was asked for a disk labeled FINEPIX during Mass Storage Driver installation AEEA was asked for a disk labeled FINEPIX during PC Camera Driver installation was asked for the WINDOWS CD ROM during Mass Storage Driver PC Camera Driver installation When connect the camera to my PC the Add New Hardware Wizard appears When double click the removable disk icon The device is not ready error message appears A warning message appeared when removed the SmartMedia from the camera Device disconnection warning appears when disconnect the special USB cable 53 54 55 When disconnect the special USB cable and double click the removable disk icon a message appears and the window does not open FinePixViewer automatic startup is slow want to stop the FinePixViewer from launching automatically 56 Connection e Image Viewing The camera and PC are connected but no removable disk icon is displayed 57 The PC hangs when access the SmartMedia The PictureHello videoconferencing window does not open PictureHello videoconferencing does
37. anual for your camera handy and read it in conjunction with these instructions To View Images Using FinePixViewer TIP For detailed information on how to use the FinePixViewer and DP Editor software refer to English pdf in the folder in which FinePixViewer and DP Editor were installed Do not perform any of the following operations during camera access as this could result in damage to the data on the SmartMedia or damage to the SmartMedia itself Switch the camera off Touch any of the camera control buttons Disconnect the USB cable Remove the SmartMedia Open the SmartMedia cover Remove the camera batteries Remove the camera from the cradle Do not use your computer to format the SmartMedia in the camera as this may make the card unusable for taking pictures e If you use a SmartMedia that was formatted on the camera and replace a folder on the SmartMedia with a folder with the same name on your hard disk the files may be corrupted Delete the folder on the SmartMedia or rename the folder before copying it to the SmartMedia 1 Start up your Macintosh 2 Select the camera settings If your camera has DSC Mass Storage and PC Camera functions in the USB setting such as FinePix6800 ZOOM Load a SmartMedia containing images you have shot into the camera Select DSC in the camera s USB setting If your camera has only the DSC Mass Storage function in the USB setti
38. ary depending on the country e The services are frequently updated so we recommend that you access them regularly In order to access the service you need to have an internet connection provided by an ISP Internet Service Provider You must have the hardware and software required for connecting to the Internet The FinePix Internet Service does not include any connection fees charged by your service provider or the normal telephone charges for dialing your service provider s access number User Registration To use the FinePix Internet services users must first register Follow the steps below to register Users can be registered for free 1 Double click the FinePixViewer icon in the installed folder 2 Click the User s Registration button The operation selection dialog box appears lt User s Registration button gt 3 Select User s registration and click the OK button f you are not already connected to the Internet connect at this point A dial up dialog box may be displayed Q Menu acquisition if you have already registered Only select menu acquisition if you have already completed the user registration process and you have re installed FinePixViewer etc Operation Selection User s registration for first time registration 73 4 The User s Registration dialog box r opens Select the country or area where you ar
39. at your new hardware device renses m zigiz flo Eat yew Fyverter Joos Hep e m gt G Seh Fees iay A OF X wp P Agden led My Corpse 2 es mr s a amp Fi Poppy A Local Disk IC PHOTODE My Computer 0 Saer ergh 5 tamala E w Corpse When 5 does not appear S First uninstall Mass Storage Driver See P 49 Re install Mass Storage Driver See P 16 J 19 Windows 2000 Professional 7 The Found New Hardware und new tardmare Wizard Wizard dialog opens Click the Next gt button If the dialog box does not appear uninstall and then re install the Mass Storage Driver See P 16 49 Welcome to the Found New Hardware Wizard Ther wra hepi you install a device chives tor a hasaan dence 8 Select Search for a suitable driver for my device yak recommended and then w click the Next gt button G ase evice Drivers em Thet mand wll compete the intallsion for this derce a araa Daa teuean a hardware device work Windows reeds Covet rae Gereice To locate dier fee ard compita the Tolosonckh Hed What do you want the wizard to do Display a list of the known drivers for this device so that car Ainme prog sen thst anistia a hardana rece to wath wah E Bearch ior a vatable diver kor my device ecommended LE C aplay a kit of the known Givers for tia device 10 that can choose a specitic reve lt Back Can
40. d How to Read It 05 15 Installing the Mass Storage Driver 0 0 0 eee eee eee eee 16 Installing the PC Camera Driver 0 0 e eee ee eee 22 Using the Software on WINCOWS ccseceeeeesseeeeseseeeeeseeneeeeeeeenes 28 Connecting the Camera and PC and Viewing Images 28 Attaching Images to E mail Messages in FinePixViewer 32 Using the FinePix Internet Service 0 0 00000 c eee eee 35 User Registration 0 0 0 cc eee 35 Videoconferencing Using PictureHello 000000 38 Customizing the Camera 0 0 c cece ete 44 Using Videolmpression 0 000 c eee tees 45 Uninstalling Software from a Windows PC ccseseeeeseeeeeeeeeeees 49 Uninstalling the Driver 0 0 0 eee 49 Uninstalling FinePixViewer DP Editor and Exif Launcher 50 Troubleshooting weceiiee cicceiesiecscseeeteeetenseanccwtecsssesteteedesnteeevesseteneeiecess Installation on a Macintosh Pre installation Checklist 0 00 0 0000 cece eee eee Installing the Software 2 2 eee The User s Guide PDF and How to Read It 2 000 68 Using the Software on a Macintosh ccssecssecesseeeeeeeeseeneeeeeeeenes 69 Connecting the Camera and Macintosh and Viewing Images 69 Attaching Images to E mail Messages in FinePixViewer 71 Using the FinePix Internet Service 00 0 c eee eee User Registration 4
41. d How to Read It To read the FinePixViewer User s Guide PDF you must have Adobe Systems Acrobat Reader installed on your computer See P 14 for information on installing Acrobat Reader E Reading the User s Guide 1 Select Start Programs FinePixViewer and click English pdf Acrobat Reader starts up and displays the User s Guide 2 To jump to the relevant page click the desired topic listed in the Contents or Bookmarks To view the bookmarks click Show Bookmarks in the Window menu For more information on how to use Acrobat Reader refer to the Online Guide in the Acrobat Reader Help menu E Printing the User s Guide 1 Click Page Setup in the File menu and specify the required settings Paper Layout etc f you print the manual at the original dimensions each page fits on one sheet of A4 paper in Portrait layout 2 Click the Print button or select Print in the File menu 3 Specify the range of pages to be printed and the number of copies etc and then click the OK button The available options vary depending on your printer and printer driver software Refer to your printer driver manual for details For more information refer to the Online Guide in the Acrobat Reader Help menu 15 Installing the Mass Storage Driver Installing Mass Storage Driver allows you to transfer files recorded on the camera to your PC
42. d in the PictureHello window If live images are not displayed installation was not completed successfully Refer to Troubleshooting P 59 Windows 2000 Professional 6 The Found New Hardware Found New Hardware Wizard Wizard dialog opens Click the Next gt button If the dialog box does not appear uninstall and then re install the PC Camera Driver See P 22 49 Welcome to the Found New Hardware Wizard To continue cick Nat 2 Ca cow 7 Select Search for a suitable Install Hardware Device Drivers driver for my device A devon dheis eae popen ha ondis a hodao Soviet mok wth recommended and then click the Next gt button Gp we recom A device chives it a software progam that makes a hardware device work Windows raedt ve fies fox your nme device To locate dives Sime arid complet the ratahahon cich Newt That wand wll complet the inutallion for thee dewcm What do you want the wizard to do T Bearch tor a stable dver for my device lrecemmended Le apia a kit of the known divers for tha device 10 that can choose a pectic Give i What do you want the wizard to do R C Display a list of the known drivers for this device so that car 9 Check that VC4CB104 INF has been detected and then click the Next gt button 10 When the Digital Signature Not Found message appears click the Yes button The Windows 2000 Prof
43. d the window does not open Possible cause Solution Is another USB removable drive Some USB removable drives do not connected operate correctly if other USB removable drives are being used at the same time Disconnect all the connected USB removable drives and then connect the camera However with some USB storage devices computer operation may become unstable when the Exit Launcher is resident See I want to stop the FinePixViewer from launching automatically below and try removing the Exit Launcher E FinePixViewer automatic startup is slow Possible cause Solution Are you running too many background Click the Start button and select applications Programs Startup from the Start menu Click the right mouse button on any shortcuts for infrequently used applications from the Startup window Click Delete from the pop up menu and then restart your PC E want to stop the FinePixViewer from launching automatically Solution Either of the two methods below can be used to prevent FinePixViewer from launching automatically e Change the Exif Launcher settings Click the right mouse button on the Exif Launcher icon in the taskbar and select Settings from the pop up menu Uncheck the Automatic startup Media insertion checkbox To restore the original setting use the same procedure to re tick the checkbox e Remove Exif Launcher C
44. ding the Videoconference on P 42 E When a call comes in A confirmation dialog box appears click the Yes button to peg eee If you click the No button the call ae does not begin The caller sees a Add masakazu den fujifilm co jp to address book message stating The other party cannot receive calls TIP If you tick the Automatically accept incoming calls checkbox no confirmation message is displayed and the call begins automatically IV Automatically accept incoming calls Bandwidth ison x E Saving a Caller s Image 1 When you click the Capture button during a call the Remote party information image is updated REE a f 41 42 Windows 2 A dialog box to confirm the save destination appears When Using the Address Book you select Paste to address book and click the OK button g the image in the address book is updated You can use the address book to check the status of other parties and to store If you accept a call you can only ETEEN m addresses To view the address book click the R Address Book button select Copy to Clipboard during the Picturcl ollo Ver 1 0 Take ae E Checking the status call A Paste to address book Click the Update Status button to check the latest status details Copy to Clipboard Pictuettebo Ver 1 0 Addens Book Click the Capture button t
45. dure begins again automatically from step Information lt gt FinePixViewer setup completed successfully 4 Finally the restart window appears Click the Restart button FinePixViewer installation is not completed until you restart your computer 5 After you restart your computer follow the procedure on P 12 to start up the Installer manually Use the same procedure to install Acrobat Reader To read the FinePixViewer User s Guide PDF you must have Acrobat Reader from Adobe Systems Inc installed Acrobat Reader installation does not require a restart FUJIFILM Fi inePi X Viewer Installing the following Acrobat Reader instali lt b Install FinePixViewer 22 install Acrobat Reader 2 Install PhotoDeluxe and ActiveShare Cancel 6 Use the same procedure to install PhotoDeluxe and ActiveShare When you have finished installing ActiveShare you may be asked to restart your computer In this case begin installing PhotoDeluxe without restarting your computer If a dll file not found message appears during installation there is another application running in the background a screen saver or similar application that could not be shut down in step 1 Forcibly shut down the application Refer to your Windows manuals for information on how to forcibly shut down an application 14 Windows The User s Guide PDF an
46. e button Refer to the Owner s Manual for your camera for details Is PC Camera selected as the camera s USB setting Is the special USB cable connected to the camera cradle and to the computer Change the camera s USB setting to PC Camera Refer to PC Connection in the Owner s Manual for your camera for details Check that one end of the special USB cable is connected to the camera cradle and the other end is connected to the computer Are you using a compatible operating system Is PC Camera Driver enabled The USB Driver should be used with Mac OS 8 6 to 9 1 It is not compatible with Mac OS X Enable USB04CB_VcShim and USBO4CB_VcDriver in the Extensions Manager and restart your Macintosh Is another video input device selected Select USB PC Camera Refer to the Videolmpression User s Guide for information on how to select the video input device Is another application displaying the live images from the camera Quit any other application that is displaying live images Did you disconnect the special USB cable or switch off the camera cradle during live image display Quit Videolmpression and then restart your PC Check that the special USB cable is connected correctly to the camera and your PC and then switch the camera cradle on E My camera will no longer play back image files Possible cause Solution Did you re
47. e Copy files dialog box click the OK button to install the driver Then click the Finish button OS Type Name of Folder Windows 98 DA Windows Me D Usbdrv Winme Windows 2000 Professional DA When using CD ROM Drive D E was asked for a disk labeled FINEPIX during PC Camera Driver installation Solution Click the Browse button in the Copy files dialog box ln the dialog box that then appears select the CD ROM icon in the drive display area and then click the OK button ln the Copy files dialog box click the OK button to install the driver Then click the Finish button E was asked for the WINDOWS CD ROM during Mass Storage Driver PC Camera Driver installation Solution Load the Windows CD ROM into the CD ROM drive Click the Browse button in the Copy files dialog box ln the dialog box that then appears select the CD ROM icon in the drive display area refer to the information in the table below and specify the appropriate folder and then click the OK button In the Copy files dialog box click the OK button to install the driver Then click the Finish button OS Type Name of Folder Windows 98 D win98 Windows Me D win9x Windows 2000 Professional D i386 If no Windows CD ROM was supplied with your PC contact your PC manufacturer When using CD ROM Drive
48. e living and click the OK button The browser starts up and opens the user registration page Use this page to register as a user ia internet oe fee LAP AIH Poche hmmm pn aeaiaioe See be pr mee After you register a confirmation e mail message is sent to you Be sure to enter a valid e mail address at which you can receive the message The actual user registration page may differ slightly in appearance from the sample shown here If the country or area where you are living does not appear in the pull down list select OTHERS A button linking to the English home page for FUJI PHOTO FILM CO LTD TOKYO JAPAN will be displayed Important Information for Internet Users Viruses A virus infecting your PC can result in the loss of important data or the sending of unwanted e mail messages to the people stored in your address book Do not open downloaded files or files received as e mail attachments unless you are certain of their content 74 Macintosh Using the Services Once user registration is completed you can use the FinePix Internet services E Selecting services 1 Click the menu button for the service you want to use ex If you are not already connected to the Internet the software automatically attempts to connect for dial up connections Operation after you click the menu button differs depending on the button you click For instance you may jump to your
49. eel ie a D e 9 In Optional search locations tick the CD ROM drives checkbox and then click the Next gt button If any checkboxes other than CD ROM drives are ticked clear the a aeien nt todos soak te os et ticks so that CD ROM drives is the only checkbox ticked Saach or dhive fins fx the towang hundare devs USB Mass Storage The witaed searches tor salable divers in s diver ditabaee on your computer and in any ol the lolowang eptenal search locabons that you specty To stat the samch cick Newt If you aie samching on a Repgy dik ce CD AOM dive wet the thopey dik or CD betore chohing Newt Optional sesch locations er go n I Speciy alecation E v CD ROM drives I Specify a location a C Yes The screen shown may differ slightly depending on the type of computer 20 10 Check that USBS04CB INF has been detected and then click the Next gt button 11 When driver installation is completed the screen shown at right appears Click the Finish button 12 Installation is completed when a new removable drive icon the connected camera appears in the My Computer window First uninstall Mass Storage Driver See P 49 Re install Mass Storage Driver See P 16 When does not appear Windows Driver Fides Search Results The ezanit hant fraza cmmechareg bor chr lie toe yous hardware device Thm vazad bourad a di
50. een for the applications provided on the CD ROM appears click the Exit button to exit the screen 3 Select PC Camera in the camera s USB setting Refer to PC Connection in the Owner s Manual for your camera for more information on camera operation and the USB setting e It is strongly recommended that you connect the AC power adapter when you are using a USB connection to avoid loss of power while you are using the camera 4 Using the enclosed USB cable connect the camera or the cradle to the USB port on your computer and then switch the camera on 5 A message appears in the New Hardware dialog box indicating that USB PC Camera has been detected See P 25 if you are using Windows Millennium Edition See P 26 if you are using Windows 2000 Professional 22 Windows Windows 98 98SE If you are asked for a disk labeled FINEPIX during installation refer to Troubleshooting see P 54 6 The Add New Hardware Wizard dialog appears Click the Next gt button Add New Hardware Wizard NOTE Thee vezard se ches for new divers lor If the dialog box does not appear uninstall and then re install the PC Camera Driver See P 22 49 USB PC Camera A device diver is a software progam that maker hardware dence work C Neas Cancel C J 7 Select Search for the best driver for your device Recommended and click the Next gt
51. en restart your Macintosh and select Empty Trash from the Special menu Uninstalling Exif Launcher FinePixViewer and DP Editor 1 After you have quit Exif Launcher in Exif Launcher Settings in the FinePixViewer Settings menu move the Exif Launcher file from the Startup Items folder in the System folder to the Trash Then select Empty Trash in the Special menu 2 Quit FinePixViewer and DP Editor and move the FinePixViewer and DP Editor files to the Trash Then select Empty Trash from the Special menu 82 Troubleshooting If the software does not operate correctly but the problem does not match any of those listed below check that you are using the correct hardware and software See P 64 If the problem persists even though you are using the correct hardware and software refer to the table below and then see the reference page listed for your problem with Page When I connected the camera to my PC the Required software not found message or Required driver cannot be used message appears 82 When I connected the USB cable Mac OS displayed the Initialize disk message The PC hangs when access the SmartMedia The camera and PC are connected but no removable disk icon is displayed 83 Connection e Image Viewing A warning message appears when remove the SmartMedia or disconnect the USB cable from the camera can t log
52. en the English pdf file in the Manual folder inside Vimpress on the enclosed CD ROM e Check on the Internet by clicking the link in the bottom right corner of the screen Use the contact details printed on the back cover to contact FUJIFILM Making Your Own Movies E Store the movie in an album To work with still images video and sound you first have to import them into the album window 1 Inthe Start menu select Programs ArcSoft Videolmpression ArcSoft Videolmpression 1 6 to launch Videolmpression 2 Click the new button to open an album window video Impress msa video _ mpression 3 Drag the thumbnails from FinePixViewer and drop them into the album window lt FinePixViewer gt 45 Windows E Add a storyboard 3 When you click the save button the Save dialog box In the storyboard you select the files to be used in the movie and set the appears Specify the save location file name etc and save order in which the files are played the movie file Drop images into here TIP If you leave the mouse pointer positioned over a button or image for a few es Drop Sounds m into here seconds information about that button or image is displayed In any window you can access the online help by clicking e In addition to MPEG you can choose from a wide range of formats for saved files Capturing Live Images If you are u
53. eo Size C Capture Video Video Size stop Capture D gt Sound Setting Capture Photo 8 Click the Stop Capture button to stop recording The movie data will be automatically saved to a file and imported to the Album 9 Click the Done button to return to the Album window Video Setting Stop Live J Video Size J Capture Video Sound Setting Capture Photo You must have a sound card installed and speakers and a microphone connected to your PC to input and output sound The time required for playing and saving images varies depending on the performance of your PC Do not perform any of the following while live camera images are being displayed as this could cause your PC to freeze see P 85 Switch off the camera Touch any of the control buttons on the camera Disconnect the USB cable Remove the SmartMedia Open the SmartMedia cover Remove the camera battery Remove the camera from the cradle e Macintosh Uninstalling the Software on a Macintosh Use this procedure only when the installed software is no longer required or when software installation fails Uninstalling Mass Storage Driver and PC Camera Driver First check that the digital camera is no longer connected Then open the Extensions folder on the hard disk and move the following four files to the Trash USB0O4CB_StorageShim USB04CB_StorageDriver USB04CB_VcShim USBO4CB_VcDriver Th
54. es the other party that the call has begun End Call button Close button Ends a call Exits PictureHello Address Book button Address input field Opens the address book Used for specifying the party to be called You can use this field to directly type in the other party s e mail address Capture button Pauses the video image of the other party and saves the paused frame as a still image O Remote party information Reflects the information in the address book Own information E mail address used at user registration Message to other party Message entered during login Answer automatically checkbox Tick this checkbox to begin videoconferencing automatically Bandwidth network speed Select the network connection speed used for calls from this list If you change the bandwidth you must then restart FinePixViewer Pause If you uncheck this item the live image on your screen begins to move When you want to check whether the live image is displayed correctly uncheck this item Pause is unchecked automatically during calls Items other than Pause and Copy PictureHello automatically selects the optimum setting Ordinarily these settings can be ignored 39 E Preparations for videoconferencing to be followed by both parties 1 Exchange e mail address the address used at FinePix Internet
55. essional CD ROM may also be required during installation In this event switch CD ROMs as directed by the on screen instructions Windows Driver Files Search Results The ward huss rected saach fox covet fine hoe your hardware devin Tha wizard fourd a chive fox the folowing devien o USB PC Camera Windows found a diver for fis device To inital the diver Windows found click Next DE owotcbiotni lt Back Caneel Digtal Signature Not found J The Microsoll digkal signature allama thal sollware has bann tested with Windows and that the softwinen has not been stered since it war tested The softrrare you are abou to install doss not conlan a Micioselt digital signature Theseion theen is ro that thes cottwrare works comectly with Werrdoves USB PC Canna i you wart to snach foe Microsoft cigtaly signed software wish the Windows Update Web site at Ntg_ endowsupdete exctocui com lo vee d one availble Do you want to continu the installation driver a GD e 11 When driver installation is fandim tarian aa completed the screen prion iy ed E 8 In Optional search locations tick the CD ROM drives shown at right appears e checkbox and then click the Next gt button Click the Finish button BERETTE ERRE EA If any checkboxes other than CD ROM drives are ticked clear the pag eo hip E ticks so that CD ROM drives is the only checkbox ticked pe sare aca Gy atia E
56. et If you have finished using the Internet disconnect manually 43 Customizing the Camera Cameras with a customization function can be customized using special customization software downloaded from the FinePix Internet Service 1 Download the special customization software from the FinePix Internet Service or from the following web site and install it in the DSCSETUP folder in the FinePixViewer folder on your PC http home fujifilm com products digital 2 When you click the camera customization button on the FinePixViewer the customization software starts up and the settings dialog box appears Refer to the downloading web page for information on installing the customization software Refer to PC Connection in the Owner s Manual for your camera for more information on transferring data from your PC to the camera 44 Windows Using Videolmpression You can use Videolmpression to make your own movies For more information on Videolmpression refer to the contact information provided on the back cover of this manual Main Functions Allows you to create and save movies that include both still and moving images and sound Allows you to edit your movies so you can cut unwanted scenes or add captions e Provides effective ways of switching from one scene to another transitions More information on these functions and how to use them is available as follows Op
57. f the Mass Storage Use the CD ROM provided to uninstall any older versions of the Mass Storage Driver Then install the new Mass Storage Driver provided on the CD ROM Windows Troubleshooting Videoconferencing Problems E The PictureHello videoconferencing window does not open Possible cause Solution Are FinePixViewer and NetMeeting 3 01 installed Install FinePixViewer and NetMeeting 3 01 from the enclosed CD ROM See P 13 Is FinePixViewer running In the Start menu select Programs gt FinePixViewer and click FinePixViewer Is the camera cradle switched on Switch the camera on If you are using the cradle connect the AC power adapter to the cradle and press the button Refer to the Owner s Manual for your camera for details Is PC Camera selected as the USB setting on the camera Change the camera s USB setting to PC Camera Refer to PC Connection in the Owner s Manual for your camera for details Is the special USB cable connected to the camera cradle and PC Check that one end of the special USB cable is connected to the camera cradle and the other end is connected to your PC Are you using a compatible operating system Use Windows 98 Windows 98SE Windows Me or Windows 2000 Professional Is the PC Camera Driver running Double click System in the Control Panel select the Device Man
58. he CD ROM enclosed with this product on an audio CD player Doing so could damage your hearing or could damage your speakers or headphones Please note that this Guide is written on the assumption that you already have a basic understanding of how to use your PC personal computer Windows and Macintosh For basic information on using your PC Windows and Macintosh refer to the respective manuals supplied with your PC e Microsoft and Windows are trademarks of the Microsoft Corporation of the U S registered in the U S and other countries Windows is an abbreviated term referring to the Microsoft Windows Operating System e Macintosh iMac Mac OS and QuickTime are registered trademarks of Apple Computer Inc Adobe Acrobat Reader ActiveShare and PhotoDeluxe are trademarks of Adobe Systems Incorporated of the U S e Videolmpression is a registered trademark of ArcSoft Inc SmartMedia is a trademark of Toshiba Corporation All other company or product names are trademarks or registered trademarks of the respective companies Windows IMPORTANT eeaeee A E AT A E A A 2 Contents Introduction Glossary of TerMS 6 uana 6 About the Software 2 0 0 eee ete eens 8 Installation ON a Windows PC cccssecceeseeeesseeeeseeeeesseeeeseeeeesenee 10 Pre installation Checklist n nnana 0000 cece cece eee eee 10 Installing the Software 0 eee eee 11 The User s Guide PDF an
59. heck the speaker setup Check that the speakers are connected correctly to your PC In the Start menu select Programs Accessories Entertainment and click Volume Control Then adjust the volume Possible cause Solution Is the Automatically accept incoming calls checkbox ticked Uncheck the Automatically accept incoming calls checkbox Are you logged in to the server Log in to the server Is the microphone operating normally You and the other party should use the following procedure to check the microphone setup Check that the microphone is connected correctly to your PC In the Start menu select Programs Accessories gt Entertainment and click Sound Recorder Then adjust the microphone input level Troubleshooting Other Problems Live images do not appear in the Videolmpression Capture window Possible cause Solution Do you have Windows Media Player Install Windows Media Player from the installed enclosed CD ROM See P 13 Is the camera cradle switched on Switch the camera on If you are using the cradle connect the AC power adapter to the cradle and press the 6 button Refer to the Owner s Manual for your camera for details Is PC Camera selected as the USB Change the camera s USB setting to PC setting on the camera Camera Refer to PC Con
60. her e Videolmpression QuickTime ED 5 Proceed with the installation as directed by the on screen instructions See Selecting the installation destination on the next page for information on how to specify the installation destination 66 E Selecting the installation destination Macintosh Click the Open button to open the installation destination folder FUJIFILM gt Q Acrobat Distiller 3 0 Q Adobe Acrobat 3 0 Ci Adobe Acrobat 3 0 Oy Adobe Illustrator 8 0 Adobe PageMaker 6 5 Oy Apple Extra Q Apple Extras Q Applications FUJIFILM Eject _ onen J poma To install the software in the displayed folder click the Save button amp Apple Video Player 3 ApplecCD Audio Player Q Movie Player 8 SimpleText FUJIFILM Eject 3 Q Cancel 6 Use the same procedure to install Acrobat Reader eee To read the FinePixViewer User s Guide PDF you must have Acrobat Reader from Adobe Systems Inc installed Installing the following Acrobat Reader Notes on Installing QuickTime When the User Registration window opens during installation you can complete the installation without entering any data If the Connection speed window appears set the correct speed for your type of connection and proceed with the installation 67
61. hereunder you shall not copy or reproduce all or any part of Software or Documentation 3 3 You shall not modify adapt or translate Software or Documentation You also shall not alter or remove copyright and other proprietary notices that appear on or in Software or Documentation 3 4 You shall not or shall not have any third party reverse engineer decompile or disassemble Software Ownership All copyrights and other proprietary rights to Software and Documentation are owned and retained by Fuji or the third party suppliers as indicated on or in Software or Documentation Nothing contained herein shall be construed expressly or implicitly as transferring or granting any right license or title to you other than those explicitly granted under this Agreement Limited Warranty Fuji warrants to you that Media is free from any defect in material and workmanship under normal use for ninety 90 days from the date of your receipt of Media Should Media not meet the foregoing warranty Fuji shall replace such defective Media with other Media bearing no defect Fuji s entire liability and your sole and exclusive remedy with regard to any defect in Media shall be expressly limited to such Fuji s replacement of Media as provided herein N wo A oa 6 DISCLAIMER OF WARRANTY EXCEPT AS PROVIDED IN SECTION 5 HEREIN FUJI PROVIDES PRODUCT AS IS AND WITHOUT WARRANTIES OF ANY KIND EXPRESS OR IMPLIED FUJI SHALL MAKE NO WARRAN
62. ialog box indicating that USB Mass Storage has been detected See P 19 if you are using Windows Millennium Edition See P 20 if you are using Windows 2000 Professional Windows Windows 98 98SE If you are asked for a disk labeled FINEPIX during installation refer to Troubleshooting See P 54 7 The Add New Hardware Wizard dialog appears Click the Next gt button NOTE Add New Hardware Wizard This wizard searches for new drivers for If the dialog box does not appear uninstall and then re install the Mass Storage Driver See P 16 49 USB Mass Storage A device driver is a software program that makes a hardware device work 8 Select Search for the best driver for your device Recommended and click the Next gt button Add New Hardware Wizard What do you want Windows to do Display a list of all the drivers in a specific location so you can select the driver you want What do you want Windows to do _ sacs Cie coe 9 When the next window opens tick the CD ROM drive checkbox and then click the Next gt button If any checkboxes other than CD Add New Hardware Wizard ROM drive are ticked clear the ticks so that CD ROM drive is the only checkbox ticked Windows will search for new drivers in its driver database on your hard drive and in any of the following selected location
63. iles folders windows buttons etc Double click Clicking the left mouse button Windows or the mouse button Macintosh twice ts Used to open files folders etc 7 t 4 Double i click Click i Windows Macintosh E DPOF A format used for recording information on SmartMedia that specifies which images are to be printed _ Images Specifications for the images to be printed SmartMedia trimming data etc E Drag amp drop An operation used to move copy or store files and folders O Sample B Oo Gj Sample2 B Picture Picture Drag Drop 1 Position the mouse pointer over the When you reach the desired location file or folder icon you want to drag release the mouse button 2 With the mouse button held down move the mouse to another location E Drive A peripheral device used by a personal computer to store and access files A disk drive into which removable media can be loaded is referred to as a removable disk drive Typical examples include CD ROM drives and floppy disk drives Digital cameras are also handled as disk drives s JS as 8 ma a Drive icons for Macintosh Drive icons in Windows E Driver Software used by a personal computer to operate a peripheral device E Folder A location in which related files are stored Other folders can also be stored inside a folder E I
64. istration button gt 3 Select User s registration and click the OK button f you are not already connected to the Internet connect at this point A dial up dialog box may be displayed Only select menu acquisition if you have already completed the user registration process and you have re installed FinePixViewer etc Operation Selection x User s registration for first time registration Menu acquisition if you have already registered 35 4 The User s Registration dialog box opens Select the country or area where you are living and click the OK button The browser starts up and opens x internet Service EE Prete TPH EIA fn aad demelantard erected the user registration page Use this page to register as a user After you register a confirmation e mail message is sent to you Be sure to enter a valid e mail address at which you can receive the message The actual user registration page may differ slightly in appearance from the sample shown here If the country or area where you are living does not appear in the pull down list select OTHERS A button linking to the English home page for FUJI PHOTO FILM CO LTD TOKYO JAPAN will be displayed eee ypn peemenrper penne p sete a Important Information for Internet Users S H Viruses A virus infecting your PC can result in the loss of important data or the sending of unwanted e mail message
65. lick the right mouse button on the Exif Launcher icon in the taskbar and click Quit from the pop up menu Click the Start button and select Programs gt Startup Exif Launcher from the Start menu Right click the Exif Launcher icon and click Remove from the pop up menu To restore Exif Launcher create an Exif Launcher shortcut in the Startup window Windows E The camera and PC are connected but no removable disk icon is displayed Possible cause Solution Is the camera cradle switched on Switch the camera on If you are using the cradle connect the AC power adapter to the cradle and press the 6 button Refer to the Owner s Manual for your camera for details Is the SmartMedia loaded in the camera Load a SmartMedia into the camera Refer to the Owner s Manual for your camera for details Is DSC selected as the camera s USB setting Change the camera s USB setting to DSC Refer to PC Connection in the Owner s Manual for your camera for details Is the special USB cable connected to the camera cradle and to the computer Check that one end of the special USB cable is connected to the camera cradle and the other end is connected to the computer Are you using a compatible operating system The Mass Storage Driver should be used with Windows 98 98SE Windows Me or Windows 2000 Professional
66. live image display area and uncheck Pause in the menu see P 39 3 Log in If your system is set up to automatically connect to the Internet Click the 2 Login button If your system is set up for manual connection to the Internet Connect to the Internet and then click the 2 Login button 4 A message input dialog box opens Type in a message to the other party and click the OK button t When you are successfully logged in EETAS x the connection icon changes to indicate a call in progress My message can be input Hellow Messages are sent without being encoded Do not include sensitive information in your message To change the message you must log out and then log in again 40 Windows E Starting the call 1 Click the Address gt A Book button to open the ou Address Book a T 2 Click the Update Status button in the Address Book to check the status of the party you are calling If the other party is available Click the information column for the other party to select him or her and then click the Start Call button x The call begins when the other party replies If the other party is unavailable Stay logged on and wait a few minutes Click the Update Status button in the Address Book to check the status of the other party Repeat steps O and until the other party becomes available If you decide not to call see En
67. mage is displayed in the PictureHello window If live images are not displayed installation was not completed successfully Refer to Troubleshooting P 59 Wi device Chck Back bo select a diferent diver o cick Ned Windows has ineched inctaling the coftrrare thal your new idware devion sequins Windows Windows Millennium Edition Windows Me 6 The Add New Hardware Wizard dialog opens Click the Next gt button NOTE Add New Hardware Wizard e It may take a few minutes for the eo eee dialog box shown at right to appear ach hed after USB PC Camera is detected e If the dialog box does not appear uninstall and then re install the PC Camera Driver See P 22 49 The Windows Me CD ROM may also be required during installation In this event switch CD ROMs as directed by the on screen instructions ED 7 When driver installation is ace nen completed the screen ee shown at right appears Click RW ot See et ee the Finish button An Wa Windows can automaticaly search for and instal software that supports your hardware If your hardware came with malalsion meda nserl row and cick Nei What would pou like to do Butomalic somh ko a better daver Recommended Specly the location ol the dirver Advanced m 8 FinePixViewer starts up and the PictureHello window automatically opens Check that the live video image is displaye
68. mi balore anring his Setup pog Rans o p eneg turning Cicek New to contres wath the Setup progam WARNING tie progam ia protected by ooops ar end rrenan beste Unadhonzad improducton or dilrbuhers of thes progam ot ary partion of may rend in senese cord and cmn panales orad wl be prosncided to the myamum mieri postin under Lae aa ew When the User Registration window opens during installation you can complete the installation without entering any data If the Connection speed window appears set the correct speed for your type of connection and proceed with the installation 13 Select the installation destination Choose Destination Location E An installation destination window is displayed You can change the installation destination by clicking the Browse button Check the destination and then click the Next gt button Setup wi inital FinePeViewer n the tofowang holder To install to this folder click Next To install to a diferent folder cick Browse and select another Folder You can chosen not to instal FinPo by clicking Cancel to ent Soha Orstinaton Folder C Progan Fies FineP Viewer Brie c C oa Installation The installation copying files changing settings etc begins automatically Complete the installation When installation ends a confirmation window appears Click the OK button to proceed to the next installation This proce
69. n your PC and start up Windows Quit all other active applications until no applications are shown in the taskbar lt Taskbar gt aiaosa Game gee O Applications to be shut down the icons shown vary depending on the applications that are running Click the right mouse button on the application icon in the taskbar Click Close in the menu that appears to quit the application Refer to the instructions provided with your PC and applications antivirus software etc for details If the following applications are installed on your PC use Add Remove Programs in the Control Panel to uninstall the applications See P 50 Exif Viewer Exif Launcher Uninstallation cannot proceed unless you shut down all resident programs DP Editor Load the enclosed CD ROM into the CD ROM drive The installer starts up automatically If the installer does not start up automatically see Launching the Installer Manually on the next page Windows Launching the Installer Manually 1 Double click the My Computer icon 2 Double click PHOTODELUXE D in the My Computer windows Here D is the designation for the CD ROM drive 3 Double click Setup or Setup exe in the CD ROM window 7 Bo Ea Yow Go Faron Ink tie i t i aja gt Bow Up A Coy Parte Undo Ags E 0 J a a o Acrormad Actreeh Common Doniad Erg Et
70. name any files or folders inside the DCIM folder Change the file or folder names in the DCIM folder back to the original names Did you replace an image file inside the DCIM folder Do not replace image files in the DCIM folder E want to stop the FinePixViewer from launching automatically Solution automatically e Change the Exif Launcher settings not run Exif Launcher at restart Restart your computer Launcher at restart option Remove Exif Launcher Exif Launcher immediately You can use either of the two methods below to prevent FinePixViewer from launching Select Exif Launcher Settings in the FinePixViewer Settings menu and click Do To restore the original setting use the same procedure and tick the Run Exif Select Exif Launcher Settings in the FinePixViewer Settings menu and tick Quit Move Exif Launcher from the Startup Items folder in the System folder to the Trash Select Empty Trash in the Special menu To restore Exif Launcher re install the software For inquiries regarding Videolmpression North America and others 46601 Fremont Blvd Fremont CA 94538 U S A Tel 1 510 440 9901 Fax 1 510 440 1270 Web site www arcsoft com E Mail support arcsoft com Europe Unit 14 Shannon Industrial Estate Shannon Co Clare Ireland Tel 353 0 61 702087 Fax 353 0 61 702001 E Mail europe a
71. nection in the Owner s Manual for your camera for details Is the special USB cable connected to Check that one end of the special USB the camera cradle and PC cable is connected to the camera cradle and the other end is connected to your PC Are you using a compatible operating Use Windows 98 Windows 98SE system Windows Me or Windows 2000 Professional Is the PC Camera Driver running Double click System in the Control Panel select the Device Manager and check USB PC Camera in Imaging or Other Devices If USB PC Camera is marked with a yellow exclamation mark or a red cross x it is not running Uninstall and then re install PC Camera Driver see P 22 49 Is another video input device selected Select USB PC Camera Refer to the Videolmpression User s Guide for information on how to select the video input device Is another application displaying the Quit any other application that is live images displaying live images Did you disconnect the special USB Quit Videolmpression and then restart cable or switch off the camera cradle your PC Check that the special USB during live image display cable is connected correctly to the camera and your PC and then switch the camera cradle on Windows E can t log in to the FinePix Internet Service Possible cause Solution Are you able to connect to the Inter
72. net Check your PC hardware and software setup Is the FinePix Internet Service undergoing maintenance Have you completed the user registration process Log in after the maintenance is completed Click the FinePixViewer user registration button and sign on as a FinePix Internet Service user See P 35 E can t sign on as a FinePix Intern et Service user Possible cause Solution Have you already signed on under the same e mail address You cannot sign on twice with the same user ID or e mail address E My PC does not shut down correctly Solution Windows Disconnect the PC and the camera using the correct procedure and then exit Some types of PC may not shut down correctly while the camera is still connected E My camera will no longer play back image files Possible cause Solution Did you rename any files or folders inside the DCIM folder Change the file or folder names in the DCIM folder back to the original names Did you replace an image file inside the DCIM folder Do not replace image files in the DCIM folder E can t play AVI files on Windows Media Player DirectX 8 0 Solution If you want to use Windows Media Player you must install DirectX 8 0 See the Microsoft homepage or industry related magazines for information on how to acquire E can t update the Internet menu properly The
73. ng Load a SmartMedia containing images you have shot into the camera e It is strongly recommended that you connect the AC power adapter when you are using a USB connection to avoid loss of power while you are using the camera e Use only SmartMedia containing images shot on a FUJIFILM digital camera 3 Using the enclosed USB cable connect the camera or the cradle to the USB port on your computer and then switch the camera on En If a removable disk icon appears on the desktop the Untitled camera and Macintosh are correctly connected 69 70 4 Launch FinePixViewer If you are running Exif Launcher When you connect the camera or the cradle to the USB port on your PC Exif Launcher starts up FinePixViewer If you changed the Exif Launcher settings FinePixViewer will not start up If you are not running Exif Launcher Double click the FinePixViewer icon in the installed folder Exif Launcher e Exif Launcher starts up automatically when you start up your Macintosh e To quit Exif Launcher select Exif Launcher Settings in the Settings menu in FinePixViewer and then select Quit Exif Launcher immediately lt FinePixViewer startup window gt Folder tree display area Thumbnail display area e Thumbnail images for the image data recorded on the SmartMedia are displayed in the thumbnail display area This thumbnail indicates an audio file
74. nstall The process of setting up software on a personal computer E Menu A list of functions displayed at the edge of the screen Typical examples include the File and Edit menus When you click on a menu name a list of the available functions appears and you can then execute a function by moving the mouse to the desired function name lt Windows gt lt Macintosh gt file RNY view special Help File Edit View Go Bookmarks Settings Video Undo Open Ctr0 Delete Del a Slide Show oR Mail Sending Paste a Clear ae cas SelectAll HA Tint t i bai Show Clipboard Index Print p Preferences Exit E Server A computer used on a computer network such as the Internet that provides services and data to connected network users E Thumbnail A reduced image created when images are displayed as a list In FinePixViewer double clicking on a thumbnail image displays the original image E Uninstall The process of removing software from your PC and restoring your PC s settings to their original status before the software was installed lt About the Software gt Digital camera Depending on the particular camera model you purchased what you actually see may differ from the illustrations shown here If the camera s USB USB connection If the camera s USB setting is DSC setting is PC Camera Personal computer Mass Storage Driver PC Camera Driver Allows a digital camer
75. o w store or update Edt 0 Dsete E Ending a Call Click the 54 End Call button Other party s name BZ ort Other party s E mail address fan 58 Bee ae Comment not seen by the other party Message written when the other party TIP logged in If you call someone who is not already listed in the Address Book a dialog box Update Status button appears when the call ends asking you whether you would like to store the other 9 party s details in the Address Book Click the Yes button to store the kean cem be galled Status of other party information in the Address Book SA i PictureHello Ver 1 0 No Not logged in Add s Sette oe to address book E Yes Logged in ee No Logged in but busy with another call E Ending the Videoconference Unclear Unclear Click the Update Status button 1 When you click the F Logout button the connection to E Storing addresses To add a new address or edit an existing address click the New or Edit the server is ended lt a Ae ws u button Enter or modify each item and then click the OK button 2 To exit PictureHello click the 40 Close button PictureHello Ver 1 0 Address Book New Edit x Other party s name aS oo Other party s E mail address ison o 7 Comment not seen by the other party Comment cnca If you are using a dial up connection logging out does not disconnect you from the Intern
76. of 56 kbps or better E There is no live image of the other party during videoconferencing Possible cause Solution Are you or the other party trying to call outside from an in house LAN Calls cannot be made in either direction between a LAN and an external line Use a dial up connection Are you or the other party trying to call outside from a home office LAN Calls cannot be made in either direction between a LAN and an external line Use a dial up connection E Videoconferencing call notifications are not displayed Windows E can make calls but cannot use videoconferencing Possible cause Solution Is the other party able to make or accept calls Open the address book and click the Update Status button If the other party cannot accept calls try again later See P 41 Are you or the other party trying to call outside from an in house LAN Calls cannot be made in either direction between a LAN and an external line Use a dial up connection Are you or the other party trying to call outside from a home office LAN Calls cannot be made in either direction between a LAN and an external line Use a dial up connection E can t hear the other party in the videoconference The other party can t hear me Possible cause Solution Are the speakers set to playback mode You and the other party should use the following procedure to c
77. rcsoft com Taiwan 1 5th Floor 164 North Fu Shin Road Taipei Taiwan Tel 886 2 2719 0225 Fax 886 2 2719 0256 ArcSoft Taiwan Representative Office China ArcSoft Beijing Representative Office No 6 South Capital Gym Rd Beijing New Century Hotel 1910 Beijing 100044 P R China Tel 86 10 6849 1368 Fax 86 10 6849 1367 E Mail China arcsoft com Australia Marketing Results Prop Ltd P O Box 6246 BHBC Baulkham Hills New South Wales 2153 Australia Tel 61 2 9899 5888 Fax 61 2 9899 5728 E Mail david mresults ba aust com Web site www marketingresults com au W FUJIFILM FUJI PHOTO FILM CO LTD 26 30 Nishiazabu 2 chome Minato ku Tokyo 106 8620 Japan Printed in Japan This brochure uses recycled paper FGS 103103 FG
78. rd feature 2 Turn virtual memory on if necessary 3 Required to use the FinePix Internet Service The software can still be installed even if you do not have an Internet connection 4 Sound functions are required for audio input output in Videolmpression e Connect the camera cradle directly to the Macintosh using the special USB cable The software may not operate correctly if you use an extension cable or connect the camera cradle via a USB hub e Push the USB connector fully into the socket to ensure that it is securely connected The software may not operate correctly if the connection is faulty e Additional USB interface board is not guaranteed e Use the drivers the Mass Storage Driver and PC Camera Driver provided on the enclosed CD ROM When older drivers are already installed on your PC uninstall the old versions and then re install the drivers provided on the enclosed CD ROM This software is not compatible with Mac OS X Macintosh Installing the Software Before You Install the Software 1 Switch on your Macintosh and start up Mac OS 2 Check whether File Exchange is active To use a SmartMedia that is supported by the camera the File Exchange utility supplied with Mac OS must be running Select the Extensions Manager in the Control Panels and check that the File Exchange check box is ticked If not click in the box so that an X appears and then restart your Macintosh a Extensions Manager
79. re can be used only when Outlook Express is selected as your default e mail application Quit any e mail applications other than Outlook Express 4 that are currently running Click Options in the Tools menu to open the Options window Click the General tab and click the Make Outlook Express my default e mail program checkbox so that it is ticked Click the Make Outlook Express my default Simple MAPI client checkbox so that it is ticked When the confirmation message for the changed settings appears click Yes message appears The Simple MAPI client has been changed You may need to restart your machine for this change to take effect Exit Outlook Express and restart your computer Internet Properties 2 x Click OK to close the Options window and click OK again when the following Windows E Attaching Images 1 A Launch FinePixViewer In the Start menu select Programs gt FinePixViewer FinePixViewer Click the folder containing the images you want to attach Click the thumbnails for the images to select them Up to 10 images can be sent with one e mail message 4 FinePix iewer 100_FUJI File Edit View Go Bookmarks Set With the images selected click Mail Sending in the File menu You can send a total of up to 1 MB of image data at one time If the total exceeds 1 M
80. s Click Next to start the search I Floppy disk drives I CD ROM drive I Microsoft Windows Update IV CD ROM drive T Microsoft Windows Update The dialog shown may differ slightly on some types of PC 17 18 10 Check that USBS04CB INF has been detected and then click the Next gt button The Windows 98 CD ROM may also be required during installation In this event switch CD ROMs as directed by the on screen instructions 11 When the window shown at right appears click the Finish button Add New Hardware Wizard to Locabon of dives a OVUSRSOCRINE Windorrs diver bie search bor the device USB Mass Storage Windows is now ready to install the best drives for this device Ch Back to select a diferert diver or cick Ned Windows has finished installing the software that your new hardware device requires 12 Installation is completed when a new removable drive e2 icon the connected camera z E appears in the My Computer window My Computer L My Conga First uninstall Mass Storage Driver See P 49 When does not appear Re install Mass Storage Driver See P 16 Windows Windows Millennium Edition Windows Me 7 The Add New Hardware Wizard dialog opens Click the Next gt button e It may take a few minutes for the dialog box shown at right to appear after U
81. s connected Windows Installing the Software Installation on a Windows PC Pre installation Checklist E The following applications are installed by the Installer FinePixViewer E Hardware and software requirements DP Editor To run this software you must have the hardware and software described Exif Launcher below Check your system before you begin the installation QuickTime Compatible PCs IBM PC AT or compatible NetMeeting 3 01 Windows 98 computers must upgrade to this version Operating System Windows 98 including the second edition Videolmpression Windows Millennium Edition Windows Me Windows Media Player Windows 2000 Professional Acrobat Reader For installation log in using the Administrator group ActiveShare CPU Pentium 200 MHz or better PhotoDeluxe RAM 64 MB minimum Hard disk space Amount required for installation 140 MB minimum Installation Preparations Amount required for operation 300 MB minimum Display 800 x 600 pixels or better 16 bit color or better Have the Owner s Manual for your camera handy and read it Supported cameras Fujifilm digital cameras equipped with a USB interface Internet connection 2 56 kbps modem connection recommended or better or an ISDN connection Sound functions 3 Speakers microphone and sound card 1 Models with a USB interface as a standard feature and one of the above operating systems preinstalled 2 Required to use the
82. s to the people stored in your address book Do not open downloaded files or files received as e mail attachments unless you are certain of their content E Private Information If you send a message to the other party during a videoconference the message is not encoded Take care not to send important information such as telephone or credit card numbers 36 Windows Using the Services Once user registration is completed you can use the FinePix Internet services E Selecting services 1 Click the menu button for the service you want to use ex If you are not already connected to the Internet the software automatically attempts to connect for dial up connections Operation after you click the menu button differs depending on the button you click For instance you may jump to your service provider s web site or an upload dialog box may open The actual Internet menu may differ slightly in appearance from the sample shown here TIP Move the mouse cursor over an Internet menu button to view information about the service 2 When you have finished using the Internet services disconnect from the Internet for dial up connections The connection speed will vary significantly depending on the quality of your phone line and the amount of traffic on the server to which you are connected E Updating the Menu 1 Select Menu Update from the View menu 2 The User Verification di
83. se amp e a a B Setup Setup exe J a2 2 8 amp XN Unn_poc Uibo 27 obyocals lotus 3 hedden 13 2 My Compuso The way file names are displayed differs as described below depending on your computer settings e File extensions 3 letter suffixes indicating the file type may be shown or hidden e Text may be shown normally or all in uppercase e g Setup or SETUP Starting the Installation 12 1 The Setup screen appears Click the Install FinePixViewer button FUJIFILM FinePixViewer Fa Install Acrobat Reader T9 Install PhotoDeluxe and ActiveShare aaas oeces et Qu 2 A list of the applications to be installed appears Check the list and then click the OK button Installing the following After they are installed PC will be restarted lt FinePixViewer DP Editor lt Exif Launcher QuickTime NetMeeting Videolmpression Windows Media Player 3 Use the procedure given below to install each of the listed applications When installation of an application is completed installation of the next application begins automatically Check the notes and warnings Notes and warnings are displayed relating to the applications being installed Check the details and then click the Next gt button Notes on Installing QuickTime nimi aa re The pogan vl intal FnaPaViewer on Wis wordy veconeanded that you we al Window progra
84. send the message in the usual way 2 orny ies Do not quit FinePixViewer until mail transmission is complete as this will prevent the e mail with the images attached from being sent E Setting the file size for attached images When FinePixViewer attaches an image file to an e mail message it adjusts the size of the image file in accordance with the Mail Transmission Settings The file size is preset to an appropriate size for e mailing immediately following installation but this setting can also be revised When an image is resized the original image is not affected 1 Click Mail Transmission Settings in the Settings menu Mail Transmission Settings 2 Place a tick in the Resize ae checkbox and specify the emen es he number of pixels height and gt a2 ove width for resized images A File Format Conversion Cut mtGiine 3 Place a tick in the File Format Conversion checkbox and select the format compression ratio for converted files TIP To prevent image resizing remove the tick from the Resize and File Format Conversion checkboxes Macintosh Using the FinePix Internet Service If you use the FinePixViewer you can also access the FinePix Internet Service via the Internet When you register you will be able to use the various services provided in the country where you are registered The services provided v
85. sing a camera with the PC Camera function in the USB settings you can import live images from the camera It is strongly recommended that you connect the AC power adapter when you are using a USB connection to avoid loss of power while you are using the camera Refer to PC Connection in the Owner s Manual for your camera for more information on camera operation and the USB settings 1 Add files to the movie by dragging them from the album window and dropping them onto the storyboard 2 If necessary you can drag items around in the storyboard to change the playback sequence ee 1 Select PC C in th s USB setti 1 Click the edit movie button to O i ere de AN E CEMAS at eee switch to the editing window 2 Using the special USB cable connect the camera cradle to the USB port on your computer and then switch the camera 2 Click the text button and enter the text on If you have launched FinePixViewer exit the program 1 You can use the drag handle to adjust the position 3 In the Start menu select Programs ArcSoft Videolmpression ArcSoft Videolmpression 1 6 4 When the startup screen appears click the new button 3 Use the buttons below the image to specify settings such as the typeface and the time for which the text appears E Play back and save the movie 1 Click the play movie button to switch to the playback window 5 When the alb
86. that do not have a sound card installed and speakers and a microphone connected can only be used to transmit images For the best results use headphones with an attached microphone yx If your Internet connection is via a router or via a LAN connecting machines on the LAN to the Internet you cannot use videoconferencing FinePixViewer and NetMeeting 3 01 installed A completed FinePix Internet Service user registration When the user registration button 4 4 is displayed on the right side of the FinePixViewer window you must complete the user registration procedure See P 35 Important Notes on E mail Addresses for Videoconferencing Take care when using your own e mail address Disclosing your e mail address to people other than those you wish to call could result in unintentional and unnecessary videoconferencing calls from third parties Windows E PictureHello Nomenclature PictureHello Ver 1 0 Video New Window 16 Window Size Get a Camera Properties Menu displayed when you Click the right 14 Bandwidth SDN x mouse button on your IV Automatically accept incoming calls image Portrait images are inset composite images Name Explanation Connection icon Indicates whether you are logged in to the server Login button Logs in to the server Logout button Logs out from the server O Start Call button Notifi
87. tt Fditset untitied Duplicate Set arson Emon We Tews E mail Account efor mation 1 Click Control Panels Internet and then click the E mail tab 2 Check that Outlook Express is shown in Default E mail Application Ovipritg SMTP Mail Server E meil Notification Os Hew E mail C Flesh kon C Oiopioy Dialog C Piny Sount Droplet z Default E mail imie a US E Attaching Images 1 Launch FinePixViewer Double click FinePixViewer in the folder in which you installed FinePixViewer 2 Click the folder containing the images you want to attach 3 Click the thumbnails for the images to select them Up to 10 images can be sent with one e mail message 71 4 With the images selected click Mail Sending in the File menu You can send a total of up to 1 MB of image data at one time If the total exceeds 1 MB a warning message appears when you click Mail Sending If this occurs reduce the number or size of the images until the message no longer appears Open 30 Save As Close 36W Delete 0 Mail Sending p Page Setup Print 3P Index Print Print Order Q 5 The Outlook Express mail 5 amea transmission window opens and en eee the images are automatically attached to your e mail message Type in the address title and your message and then
88. ttons do not line up correctly Solution The menu data is corrupted Use the procedure below to update the menu Quit FinePixViewer Double click System Folder and then Preferences to open the Preferences folder Trash the FinePixInternetFiles folder in Preferences Start up FinePixViewer and click the Update button E The FinePixViewer Upload dialog box does not appear Possible cause Solution Do you have enough memory in your Quit any other applications that are system running Open Memory in Control Panels and increase the amount of virtual memory allocated Then restart your Macintosh E The Process aborted because error occurred during communication message appears while you are using the FinePixViewer Upload dialog box Solution Use the following procedure to increase the allocated memory Close the Upload dialog box and select the Upload file in the folder in which FinePixViewer was installed Select Get Info in the File menu The Upload Info window opens In Memory increase the Preferred Size allocation Macintosh Troubleshooting Other Problems E Live images do not appear in the Videolmpression Capture window Possible cause Solution Is the cradle camera switched on Switch the camera on If you are using the cradle connect the AC power adapter to the cradle and press th
89. um window opens click the capture button 2 Click the Play button and check the movie 46 47 Windows Uninstalling Software from a Windows PC 6 Display switches to the capture window and the live image is displayed If the live image does not appear click the Live button Recording has not yet started lesson Uninstalling the Driver E Uninstall the USB Driver in the following situations When you have installed Mass Storage Driver but the camera still does not appear as a removable disk icon 7 Use the Drives button to select USB PC Camera 8 Click the Record button to start recording 9 Click the Record button again to end recording When you want to remove an unwanted driver When you are upgrading the driver When you have installed the driver but it does not work Uninstall the driver and then re install it e Disconnect the camera beforehand e Close all files when removing drivers 1 Switch on your PC and launch Windows The recorded images are not saved to a file 2 Insert the enclosed CD ROM into the CD ROM drive E To check the images If the installation screen for the applications provided on the Click the Play button CD ROM appears click the Exit button to exit the screen 3 Launch the Uninstaller E To save the images to a file and return to the Album window 1 When you click the album button the Save dialog box opens Specify the
90. ur PC may malfunction if you remove the camera from the cradle or disconnect the USB cable without first using the Eject hardware procedure 31 32 Attaching Images to E mail Messages in FinePixViewer FinePixViewer provides a simple procedure for attaching images to an e mail message This feature can only be used when Outlook Express or Outlook2000 is selected as your default e mail application Contact your ISP Internet Service Provider for information on setting up Outlook Express or Outlook2000 E Check the following Check that Outlook Express or Outlook2000 is registered as your default e mail application 1 Click Control Panel Internet Properties and General Security Content Connections Gowan advarced then click Programs A Yoran ina AAR ENE a for each Internet service 2 Check that Outlook Express EEE al or Outlook2000 is shown in ae a X 2 lewsgroups JOuwlockExpess GG the E mail field Inlemetcatt Microsoft NeMecing id Calendar X Contact list Address Book X You can reset Internet Explorer defaults for home and search pages When Using Outlook Express 4 on Windows 98 Follow the procedure below to set up Outlook Express to attach images to e mail messages in FinePixViewer To check the Outlook Express version click About Microsoft Outlook Express in the Outlook Express Help menu This featu
91. w FUJIFILM USB Mass Storage Driver USB PC Camera Driver FinePixViewer DP Editor Exif Launcher Software Quick Start Guide Please read this guide carefully before using this software with a PC Thank you for purchasing these FUJIFILM products This Software Quick Start Guide describes how to connect the camera to the USB port on your PC and how to install the enclosed software on your PC It also provides a quick guide to using the software and a section on troubleshooting any problems that may arise Read this manual carefully to ensure that you make the best possible use of the software The functions described in this guide are available on FinePixViewer Ver 1 1 or later However some functions are not available on FinePixViewer Ver 1 0 For detailed information on using FinePixViewer and DP Editor refer to the User s Guide PDF BLoooo2 201 1 H IMPORTANT Be sure to read this page before using the Software NOTICE BEFORE OPENING THE PACKAGE OF CD ROM PROVIDED BY FUJI PHOTO FILM CO LTD PLEASE READ THIS END USER LICENSE AGREEMENT CAREFULLY ONLY IF YOU DO AGREE TO THIS AGREEMENT YOU WILL BE ABLE TO USE THE SOFTWARE RECORDED ON THE CD ROM BY OPENING THE PACKAGE YOU ACCEPT AND AGREE TO BE BOUND BY THIS AGREEMENT End User License Agreement This End User License Agreement Agreement is an agreement between Fuji Photo Film Co Ltd Fuji and you which sets forth the terms and
92. with your PC for details of how to enable the USB functions Is an older version of the Mass Storage Driver installed Use the CD ROM provided to uninstall any older versions of the Mass Storage Driver Then install the new Mass Storage Driver provided on the CD ROM Windows E The camera is connected to my PC but the PC Camera Driver installation will not start Possible cause Solution Is the camera cradle switched on Switch the camera on If you are using the cradle connect the AC power adapter to the cradle and press the 6 button Refer to the Owner s Manual for your camera for details Is PC Camera selected as the camera s USB setting Change the camera s USB setting to PC Camera Refer to PC Connection in the Owner s Manual for your camera for details Is the special USB cable connected to the camera cradle and to the computer Check that one end of the special USB cable is connected to the camera cradle and the other end is connected to the computer Are you using a compatible operating system The PC Camera Driver should be used with Windows 98 98SE Windows Me or Windows 2000 Professional If you are using Windows 2000 Professional are you logged on as an Administrator group Log on as an Administrator group Refer to the User s Manual for your PC for more information on Administrators Is PC Camera Driver
93. xViewer If you are running Exif Launcher When you connect the camera or the cradle to the USB port on your PC Exif Launcher starts up FinePixViewer If you have altered the Exif Launcher settings FinePixViewer will not start up If you are not running Exif Launcher Select Programs FinePixViewer FinePixViewer in the Start menu FinePixViewer then starts up If FinePixViewer is slow to start up refer to Troubleshooting P 56 lt FinePixViewer startup window gt Folder tree display area Thumbnail display area e Thumbnail images for the image data recorded on the SmartMedia are displayed in the thumbnail display area This thumbnail indicates an audio file Thumbnail Exif Launcher gt e When you install Exif Launcher it is registered in the startup menu and is launched automatically when Windows starts up If the icon in the figure is shown in the taskbar Exif Launcher is running To quit Exif Launcher click the right mouse button on the icon in the taskbar and select Exit from the menu that appears C vs When you quit Exif Launcher the icon will disappear from the taskbar J 29 30 Saving images on your PC The camera is connected as a removable disk drive The images on the SmartMedia are stored in folders such as the 100_FUuI folder in the DCIM folder on the removable disk drive
94. y make the card unusable for taking pictures 1 Start up your PC and double TT a click the My Computer icon eo ae TEFA a If you are running Windows 2000 eT Professional log on using the user ati account you normally use F iu is Jiro 2 Select the camera settings If your camera has DSC Mass Storage and PC Camera functions in the USB setting such as FinePix6800 ZOOM Load a SmartMedia containing images you have shot into the camera Select DSC in the camera s USB setting If your camera has only the DSC Mass Storage function in the USB setting Load a SmartMedia containing images you have shot into the camera e It is strongly recommended that you connect the AC power adapter when you are using a USB connection to avoid loss of power while you are using the camera e Refer to PC Connection in the Owner s Manual for your camera for more information on camera operation and the USB setting e Use only SmartMedia containing images shot on a FUJIFILM digital camera Windows 3 Using the enclosed USB cable connect the camera or the cradle to the USB port on your computer and then switch the camera on ts When the Removable Drive icon appears in the My Computer window the camera and PC are correctly connected The window actually shown on your PC may differ from that shown in the figure 4 Launch FinePi

Software Quick Start Guide Manual

Contents

Download Pdf Manuals

Related Search

Related Contents