Installation & User Manual Radio Remote rev1.0.3
Contents
1. and turn off the power to the receiver as well as the thruster mainswitch 1 Open the transmitter case by removing the 3 torque screws 2 Remove the battery by inserting a screwdriver or similar between battery and holder at point A and gently flip the battery out taking care not damaging the battery grips at point B 3 Insert the new battery Type CR2032 3V Brand name recommended Be sure to insert the battery with the positive pole up diagonally into the battery holder ensuring that the edge of the battery is under the battery grips B Press the battery down until secured at point A 4 Close the transmitter Put the cover back in place ensure that the rubber seal between remote upper and lower part is located correctly Place the 3 screws remember sealing washer in their recessed holes and tighten Installation amp User Manual Radio Remote rev 1 0 3 Page 16 Dimensions 36 Installation amp User Manual Radio Remote rev 1 0 3 Page 17 Installation amp User Manual Radio Remote rev 1 0 3 Page 18 Installation amp User Manual Radio Remote rev 1_0 3 Page 19 Worldwide sales and service www sIde power com SEINE es Morot SLEIPNER MOTOR AS P O Box 519 N 1612 Fredrikstad Norway Tel 47 69 30 00 60 Fax 47 69 30 00 70 www side power com sidepower sleipner no The information given in the document was correct at the time it was published2. However Sleipner Motor AS can not accept liability for any inaccuracies or omissions it may contain Continuous product improvement may change the product specifications without notice Therefore Sleipner Motor AS can not accept liability for any pos sible differences between product and document
3. 2 seconds How to use a bow thruster 1 Turn the main power switch for the bow thruster on Turn on main switch so the receiver has power 2 Turn on the transmitter by pushing the transmitter s two ON buttons The remote system is now activated and then turns off automatically appr 4 min after the last usage 3 Please take some time to exercise thruster usage in open water to avoid damages to your boat 4 Turn the bow in the desired direction By pushing the red button for port movement or the green button for starboard movement How to use the windlass 1 Turn the main power switch for the windlass on Turn on the power to the receiver 2 Turn on the transmitter by pushing the transmitter s two ON buttons The remote system is now activated and then turns off automatically appr 4 min after the last usage 3 Please consult your windlass manual for use and precautions Remote Control Deactivation Push the transmitter s OFF button for two seconds the remote control deactivates automati cally after approx 4 minutes after the last usage e If in doubt try in open water first Installation amp User Manual Radio Remote rev 1 0 3 Page 8 RC 22E Remote control ON Windlass 1 Windlass 2 Auto OFF appr 4 min Hold for 2 seconds How to use a bow stern windlass 1 Turn the main power switch for the windlass on Turn on main switch so the receiver has power 2 Turn on the t
4. Confidence by Control 4 gt SIDE POVVER Thruster Systems Installation amp User Manual Radio Remote rev1 0 3 RC 20E RC 21E RC 22E RC 23E Pep SLEIPNER MOTOR AS P O Box 519 N 1612 Fredrikstad Norway id AN Tel 47 69 30 00 60 www side power com Motos Fax 4769 30 00 70 sidepower sleipner no Made in Norway Sleipner Motor AS 2015 Contents ModE A enni 2 Technical SPECINCAlIONSs ira 3 Important PreCaUtiONS aaa 3 Receiver INStall llON illa 4 User precationis eda 6 How ouse RC cr tr geste a E E E e E E 7 Row 0 0SeRC2 Egidi ie 8 How ouse RCE Glen 9 How Ouse RCE cerre a a E O 10 Transmitter LED operation and alarm indication rr rr r rr rr rn r non na 12 ES IC CANN rai 13 Outpitsignalsdiagrtil aclee aaa 14 Programming additional transmitters iii 15 Replacing transmitter Dale ny 16 DINcrsoisll lan 17 Model range The radio remote control can control a single bow thruster windlass or a bow and stern thruster windlass combined The receiver can receive the signals of up to four transmitters Remote control kit RC 20E consists of Receiver Part no RCR 2E Transmitter incl battery Part no RCT 20E Holding bracket for transmitter unit Part no RC HOLDER Remote control kit RC 21E consists of Receiver Part no RCR 2E Transmitter incl battery Part no RCT 21E Holding bracket for transmitter unit Part no RC HOLDER Remote
5. control kit RC 22E consists of Receiver Part no RCR 2E Transmitter incl battery Part no RCT 22E Holding bracket for transmitter unit Part no RC HOLDER Remote control kit RC 23E consists of Receiver Part no RCR 2E Transmitter incl battery Part no RCT 23E Holding bracket for transmitter unit Part no RC HOLDER Additional transmitters can be ordered separately The transmitter and the receiver have the same factory preset code so no programming is neces sary The battery is already inserted in the transmitter When additional transmitters are to be used the new transmitter s must be paired with the re ceiver please see programming section We Sleipner Motor AS declare that this device complies with health and safety requirements according to the Directives EN301 489 3 V1 4 1 2002 EN301 489 1 V1 4 1 2008 IEC 60533 1999 EN300 220 1 V2 3 1 2010 EN300 220 2 V2 3 1 2010 Installation amp User Manual Radio Remote rev 1 0 3 Page 2 Technical specifications Transmitter Receiver ea a sn 10 C 55 C 15 C 55 C Sa 9 Weight g Od Voltage BBO toad max _________M Important precautions e With the boat on land only run the thruster for a fraction of a second as without resistance it will accelerate very fast to a damaging rpm e This manual is intended to support educated experienced staff e When installed in boats approved or classified according to internat
6. ional or special national rules the installer is responsible for following the demands in accordance with these regula tions classification rules The instructions in this guide can not be guaranteed to comply with all different regulations classification rules e The transmitter and the receiver have the same factory preset code so no programming is nec essary When additional transmitters are to be used follow the instructions in the programming section on page 15 Installation amp User Manual Radio Remote rev 1_0 3 Page 3 Receiver installation Prior to installation it is important that the responsible installer reads this guide to ensure necessary acquaintance with this product WARNING Remote receiver power supply negative lead must be connected to the thrusters s negative lead Power to the thruster s must be switched off during installation Install the receiver minimum 1 meter 3ft from high power cables and data communication cables or other sources of electrical interference i e navigation instruments radio communica tion devices electric motors and generators Install the receiver minimum 1 meter 3ft above sea level e Install the receiver outside of shielded areas for radio signals i e boxes made of metals or other material with shielding properties Install the receiver in a dry environment where no condensation can enter the unit The receiver assembly is not waterproof e Mount the
7. mote middle buttons gives you the opportunity to operate both thrusters in the same direction with one keypress making sidewards movement easier How to use the bow stern windlass i 2 Turn the main power switch for the windlass on Turn on the power to the receiver Turn on the transmitter by pushing the transmitter s two ON buttons The remote system is now activated and then turns off automatically appr 4 min after the last usage Please consult your windlass manual for use and precautions Remote Control Deactivation Push the transmitter s OFF button for two seconds the remote control deactivates automati cally after approx 4 minutes after the last usage Turn off the power switch for the receiver If in doubt try in open water first Installation amp User Manual Radio Remote rev 1_0 3 Page 11 Transmitter LED operation and alarm indication State LED status Alarm status Transmitter ON The yellow LED s No sound blink each second Buttons activated The yellow LED s No sound blink fast AI LED s on Connection lost Red LED is blink 3 beeps from the ing once each buzzer each second second Low battery Red LED blink Receiver LED indicator State LED status Power on the receiver and no transmitter connected Green LED is toggling Power on the receiver and at least one transmitter Green LED lit connected No power to the receiver Both LED is off Receiver in pairing mode Bo
8. ort Bow Stern thruster nail je Oe gt POWER Remote control OFF Turn boat to Starboard Auto OFF appr 4 min Hold for 2 seconds How to use a bow stern thruster 1 Turn the main power switch for the bow stern thruster on Turn on main switch so the receiver has power 2 Turn on the transmitter by pushing the transmitter s two ON buttons The remote system is now activated and then turns off automatically appr 4 min after the last usage 3 Please take some time to exercise thruster usage in open water to avoid damages to your boat 4 Turn the bow stern in the desired directiony by pushing the red button for port movement or the green button for starboard movement How to use a bow amp stern thruster combined The combination of a bow and stern thruster offers total manouverability to the boat and the opportunity to move the bow and the stern separately of each other The remote middle buttons gives you the opportunity to operate both thrusters in the same direction with one keypress making sidewards movement easier Remote Control Deactivation Push the transmitter s OFF button for 2 seconds the remote control deactivates automati cally after approx 4 minutes after the last usage e If in doubt try in open water first Installation amp User Manual Radio Remote rev 1 0 3 Page 7 RC 21E Remote control ON Turn boat to Port Windlass Auto OFF appr 4 min Hold for
9. r Green status LED blinking and that the transmit ter that should be paired is off 2 Push the Pair Button on the receiver to put the receiver in pairing mode as shown above Both red and green led s should start to blink simultaneously 3 Within 10s after the receiver pair button is pushed set the transmitter in pairing mode by holding the off button and pressing both ON buttons at the same time all the transmitter LED s turn on indicating that it is set in pairing mode When a pairing signal is received from the receiver the transmitter LED s while turn off and the system is ready to be used If no pairing signal received within 10s the transmitter will leave the pairing mode 4 Additional transmitters must be programmed according to step 2 3 You can pair up to 4 transmitters 5 To clear all transmitters paired with the receiver hold the pair button on the receiver for approximately 10s until the red and green led stop blinking When the LED s stop blinking re lease the pair button the green led will again start to blink when the receiver has completed the reset process The receiver is then ready to pair with up to four transmitters Installation amp User Manual Radio Remote rev 1 0 3 Page 15 Replacing transmitter battery N UD Ms Da Z lt x JD Ge LLELLE I i I WARNING Before working on the transmitter deactivate the transmitter and the receiver push OFF on the transmitter s
10. ransmitter by pushing the transmitter s two ON buttons The remote system is now activated and then turns off automatically appr 4 min after the last usage 3 Please consult your windlass manual for use and precautions Remote Control Deactivation Push the transmitter s OFF button for two seconds the remote control deactivates automati cally after approx 4 minutes after the last usage Installation amp User Manual Radio Remote rev 1 0 3 Page 9 RC 23E Remote control ON Turn boat to Port Bow Stern thruster Hold for 2 seconds Windlass 1 Windlass 2 al i lt gt Installation amp User Manual Radio Remote rev 1 0 3 Page 10 How to use a bow stern thruster 1 Turn the main power switch for the bow stern thruster on Turn on main switch so the receiver has power Turn on the transmitter by pushing the transmitter s two ON buttons The remote system is now activated and then turns off automatically appr 4 min after the last usage Please take some time to exercise thruster usage in open water to avoid damages to your boat Turn the bow stern in the desired directiony by pushing the red button for port movement or the green button for starboard movement How to use a bow amp stern thruster combined The combination of a bow and stern thruster offers total manouverability to the boat and the opportunity to move the bow and the stern separately of each other The re
11. receiver using the four holes please see picture on page 5 e The receiver must have a separate power supply fitted with a 5 Amp fuse in the positive lead that has either a separate power switch or is shut of by the thrusters system main power switch The receiver can not be powered by the thrusters windlass control looms even if you find positive and negative lead there e Connect the supplied wiring harnesses to the receiver unit according to the wiring diagram on page 13 Connect thrusters and windalsses to the appropirate connectors according to diagram e For use with other windlass brands connections must be determined by the installer according to output signals diagram on page 14 NB Max load on the windlass signal output is 4A If the windlass requires more than 4A use extra control relay Note Faulty installation will render all warranty given by Sleipner Motor AS void Installation amp User Manual Radio Remote rev 1 0 3 Page 4 Mount the receiver by using the 4 holes Installation amp User Manual Radio Remote rev 1 0 3 Page 5 User precautions Ensure that you know the location of the main battery switch that disonnects the thruster from all power sources batteries so that the thruster windlass can be turned off in case of a mal function The maximum continues usage time of the electrical thruster is approx 3 minutes The electro motor has a built in thermal cut off switch that will shut it off when overhea
12. th the red and green LED blinking Installation amp User Manual Radio Remote rev 1 0 3 Page 12 Electric diagram To Thruster To Thruster Control Panel Control Panel A IN N i IN BOW STERN To Bow To Stern Thruster Thruster BLACK RED Battery 12 24V Remember 8 ngn Power cables must be connected to the battery as shown Remaining wires must be cable tied well To Windlass To Windlass Control Panel Control Panel L Nn a BOW STERN To Bow To Stern Windlass Windlass Installation amp User Manual Radio Remote rev 1 0 3 Page 13 Output signals diagram RED Thruster Positiv BLUE Thruster STBD Thruster Bow GREY Thruster POR YELLOW Automatic Mainswitch Enable I RED Thruster Positiv BLUE Thruster STBD Thruster Stern GREY Thruster PORT YELLOW Automatic Mainswitch Enable I RED COMMON BLUE Windlass IN GREY Windlass OUT Windlass Bow RED COMMON BLUE Windlass IN GREY Windlass OUT Windlass Stern DL Installation amp User Manual Radio Remote rev 1_0_3 Page 14 Programming additional receivers POWE f Pair Button The original transmitter and receiver have the same factory preset code so that no programming is necessary When additional transmitters are to be used the additional transmitters has to be paired with the receiver 1 Be sure that there is power on the receive
13. ting and re engage it when it has cooled down some This should be considered when planning your manouvering Never use a thruster close to somebody in the water as the thruster will draw objects close by into the tunnel and contact with the rotating propellers will cause serious injuries Never use a windlass close to somebody in the water an unexpectedly drop of the anchor can cuse serious injuries If the thruster stops giving thrust while the electric motor is running chances are that there is a problem in the drive system You must then immediately stop trying to run it and turn it off as running the electricmotor for more than a few seconds without resistance from the propeller can cause serious damage to the electricmotor When leaving the boat always turn off the main power switch for the thruster windlass and turn off the power to the receiver We advice to always keep the main engine s running while using a thruster windlass This will keep the batteries in a good charge condition This will also give better performance to the thruster It is the owner captain other responsible party full responsibility to assess the risk of any unexpected incidents on the vessel If the thruster stops giving thrust for some reason while maneuvering you must have considered a plan on how to avoid damage to persons or other objects Installation amp User Manual Radio Remote rev 1 0 3 Page 6 RC 20E Remote control ON Turn boat to P
Download Pdf Manuals
Related Search