User`s Manual
Contents
1. TIT e non NEC Value Series MuiltiSyncXV User s Manual NEC 78131481 1 7 29 98 8 44 AM 78131481 2 TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Ka RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient A magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit This symbol alerts the user that important literature concerning the operation and A maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems Canadian Department of Communications Compliance Statement 2 os FCC Information J Use the attached specified shielded cable with the JC 1571VMA 2 color monitor so as not to interfere with radio and television reception 1 Shielded captive type signal cable Use of other cables and adapters may cause interference with radio and television re2. Stock No 004 000 00345 4 DOC This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouiller du Canada Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to C S A 22 2 950 Ce produit porte la marque C UL et se conforme aux r glements de s rele Canadiens selon CAN CSA 22 2 No 950 C UL 7 29 98 8 44 AM Packaging Quick Start Introduction Screen Technology Plug and Play ErgoDesign Features Power Manager Reduced Emissions e Multiple Frequency Technology Controls Control Panel Specifications Recommended Use Setting Up a Healthy Work Environment MultiSync isa registered trademark of NEC Technologies Inc in the U S and of NEC Home Electronics Ltd in Canada UK Germany France Spain Italy Austria Benelux Switzerland Denmark Finland Norway and Saudi Arabia ErgoDesign and OptiClear are registered trademarks of NEC Technologies Inc in the U S and Canada XVi5 CromaCear Reduced Magnetic Field IPM FastFacts and FullScan are trademarks of NEC Technologies Inc in the U S NEC is a registered trademark of NEC Corporation Copyright 1996 by NEC Technologies Inc Windows and Windows 95 are registered trademarks of Microsoft Corporation All Rights Reserved All other brands and product names are
3. function features and installation of the MultiSync monitor 900203 Names and addresses of other groups involved in standards and features of the MultiSync monitor 900204 Detailed information on connecting the MultiSync monitor to a Macintosh 153006 Detailed information on setting up a healthy work environment 900108 For more information about FastFacts information see page 20 78131481 26 KOR NM TIM Directory of Telephone Numbers Customer Service Direct Sales FastFacts Information Literature amp Sales Information MultiSync Fulfillment To order software and accessories MultiSync Monitor Technical Support Technical Support Fax 800 388 8888 800 374 8000 800 366 0476 800 NEC INFO 800 820 1230 800 632 4662 508 635 4666 NOTE To request the Setting Up a Healthy Work Environment brochure call NEC at 800 820 1230 or NEC FastFacts information at 800 366 0476 and request document 900108 i 7 29 98 8 44 AM PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document including all designs and related materials is the valuable property of NEC and or its licensors as appropriate reserve all patent copyright and other proprietary rights to this document including all design manu facturing reproduction use and sales rights thereto except to the extent said rights are expressly granted to others The NEC product s discussed in t
4. s Energy Star requirements and Europe s TCO NUTEK power management requirements Energy Star products use less than 30 watts when in the main power saving mode The NUTEK specification 803299 requires automatic power down to less than 30 watts in the suspend mode and less than 8 watts in the off mode 78131481 8 When in the maximum power down mode the Multi Sync XV15 monitor will consume approximately 10 of the total power drawn under normal operation which follows the Video Electronics Standard Association VESA approved DPMS power down signaling method This innovation adds up to 90 energy savings longer monitor life environmental protection reduced emissions and reduced air conditioning costs of the work environment Reduced Emissions The MultiSync XV15 monitor incorporates Reduced Magnetic Field technology designed to reduce magnetic and alternating electric field emissions and static electricity NEC MultiSync monitors follow the strictest magnetic field alternating electric field and electro static recommendations of the Swedish Board for Technical Accreditation or SWEDAC previously known as MPR National Board for Measurement and Testing and TCO excluding alternating electric fields which specify maximum recommended values of electric and magnetic fields 7 29 98 8 44 AM Mn ra Multiple Frequency Technology Multiple Frequency Technology automatically adjusts the monitor to th
5. card computer e Check the connector for bent or pushed in pins Image is scrolling or unstable Signal cable should be completely attached to the computer e Check the pin assignments and signal timings of the monitor and your display card with respect to recommended timings and pin assignments e If the Mac adapter is used check for proper connection or make sure the display card is Mac compatible and that the card is properly seated in the computer LED on the monitor is not lit no green orange or yellow color can be seen e Power Switch Degauss should be in the ON position and the power cord should be connected e Make certain the computer is not in a Power Saver mode touch the keyboard or mouse Picture is fuzzy 78131481 20 e Adjust the Brightness and Contrast Controls e Turn the Power Switch Degauss OFF then ON again CAUTION A minimum interval of 20 minutes should elapse before this procedure is used a second time 7 29 98 8 44 AM Troubleshooting Chart Problem e NM TIM Check These Items Picture bounces or a waving pattern is present in the picture e Move electrical devices that may be causing electrical interference away from the monitor e See inside cover of this manual for FCC information Displ ay image is not centered too small or too large e Use the Vertical and Horizontal Size and Position Controls to adjust the image Color looks blotchy e Turn the Power
6. card you are using and have its manual nearby 78131481 22 If it is more convenient to fax a question to NEC s technical support the fax number is 508 635 4666 The BBS The NEC Remote Bulletin Board System BBS is a great way to keep in touch with NEC It is an A i service accessible with your system and a modem You can tell us things about yourself your experience with the product and leave messages requesting on line hele Also the BBS keeps you up to date on the latest NEC products and lets you download new product information when it s available To contact the BBS using any computer with a modem dial 508 635 4706 Communications parameters are 300 1200 2400 9600 14 4k 28 8k bps no parity 8 data bits 1 stop bit Electronic Channels Additional information and technical support can be obtained by accessing the following electronic channels Internet E mail tech support nectech com Internet ftp site p nectech com CompuServe go NECTECH America Online eyword NECTECH World Wide Web http www nec com 7 29 98 8 44 AM Limited Warranty NEC Technologies Inc hereinafter NECTECH warrants this Product to be free from defects in material and workmanship and agrees to repair or replace any part of the enclosed unit which proves defective under these terms and conditions How Long is the Warranty Parts and labor are warranted for three 3 years from the date of the first consumer purchase Spare p
7. EAR CRT 5 10 Degauss 8 9 18 19 see Power Switch Degauss e Dimensions 11 Display Area 11 Dot Pitch see Mask Pitch 5 10 DPMS 6 Dynamic Beam Focus 5 Electronic Channels 20 Energy Star EPA 6 23 78131481 25 Ka ErgoDesign Features 5 6 FastFacts Information 4 13 17 20 24 FullScan Capability 7 Horizontal Controls 8 9 19 TM IPM Intelligent Power Manager System 5 6 LED 18 Macintosh 3 4 7 18 24 Mask Pitch 5 10 MPR 6 Multiple Frequency Technology II NUTEK 6 OptiClear Screen Surface 5 10 Picture Tube 10 Plug and Play 5 Power Switch Degauss 8 9 18 19 os Reduced Magnetic Field Technology Resolutions Setting Up a Healthy Work Environment Side Pincushion Control Specifications SWEDAC Synchronization Range TCO Technical Support Troubleshooting Vertical Controls VESA Warranty Weight 7 29 98 8 44 AM 6 4 5 7 10 13 17 24 8 9 19 10 11 6 10 6 20 24 18 20 8 9 19 6 7 21 22 11 Ka 24 More Information More reference information regarding your MultiSync monitor is available on NEC s automated facsimile service FastFacts information by dialing 800 366 0476 Information MultiSync XV15 monitor Glossary More Information Macintosh Connection Healthy Work Environment Document Description Detailed MultiSync XV15 monitor information Number 1571201 Definitions of terms related to the
8. MultiSync XV15 monitor and the other end to the power outlet 5 Turn on your MultiSync monitor and computer NOTE If you have any problems please refer to the Troubleshooting section of this manual 7 29 98 8 44 AM Ka Congratulations on your purchase of NEC s MultiSync XV15 color monitor which includes Microsoft s Plug and Play compatibility NEC s ErgoDesign features IPM Intelligent Power Manager System and Multiple Frequency Technology Screen Technology The MultiSync XV15 monitor also features NEC s exclusive CROMACLEAR CRT Cathode Ray Tube the latest advancement in display technology The CromaCLear CRT patented by NEC delivers images with more clarity than found in traditional dot trio or aperture grille CRTs Unlike the conventional shadow mask with phosphor dots CromaCLear CRT phosphors appear elliptical when illuminated resulting in screen images with higher defini tion color saturation and more depth and dimension The CRomaCLEaR CRT has Dynamic Beam Focus which provides precise and continuous focus adjustments of the electron beams Dynamic Beam Focus provides optimum image quality even to the far edges of the screen You will notice the significant differ ence the CromaCLEAR CRT makes through enhanced image clarity depth and definition for realistic text graphics and video 5 78131481 7 Ka The OptiClear Screen Surface of the MultiSync XV15 CRT dramatically
9. RWISE 78131481 24 Warranty THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES THEREFORE THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU This warranty gives you specific legal rights and you may also have other rights which vary from state to state For Information Telephone 1 800 632 4662 NOTE All Products returned to NECTECH for service MUST have prior approval this may be obtained by calling the above number This Product is warranted in accordance with the terms of this limited warranty Consumers are cautioned that Product performance is affected by system configuration software the application customer data and operator control of the system among other factors While NEC TECHNOLOGIES INC Products are considered to be compatible with many systems the specific functional implementation by the customers al the Product may vary Therefore the suitability of a Product for a specific purpose or application must be determined by the customer and is not warranted by NECTECH 7 29 98 8 44 AM ANSUHFS 13 17 BBS Remote Bulletin Board System 20 Brightness Control 8 9 18 Contrast Control 8 9 18 CROMACL
10. Switch Degauss OFF then ON again See CAUTION above Left and right edges of the display image are curved either inward or outward 78131481 21 e Adjust the Side Pincushion Control e If possible position the monitor to face east Troubleshooting Support 7 29 98 8 44 AM _Troubleshooting Support FastFacts Information FastFacts information system is an easy to use automated facsimile service that provides you with information whenever you need it 24 hours a day seven days a week You can call the FastFacts information system with your touchtone telephone order a catalog listing the available documents or order the document you need Within minutes your requested information will be sent to your fax machine The information includes product brochures installation procedures quick reference guides troubleshooting information compatibility charts To contact FastFacts information dial 800 366 0476 Technical Support If the problem persists call your authorized NEC dealer or service center or NEC Technologies Inc MultiSync monitor technical support at 800 632 4662 Before you call please follow these instructions to allow for faster service Call from a location at or near your monitor Know the name and model number of your monitor MultiSync XVI5 JC 1571VMA 2 Know the name and model number of the computer you are using and have its manual nearby Know the name of the dispaly
11. a Illinois 60143 1248 Ka 7 29 98 8 44 AM Part No 78131481 Printed in U S A
12. ange between 640 x 480 832 x 624 and 1024 x 768 screen resolutions without restarting your system if the video port supports these modes You will connect your MultiSync XV15 monitor one of two ways to your Macintosh computer On board video port NuBus PDS or PCI display card 78131481 6 Quick Start Both configurations should have the same style video connec tor If you are not sure which port is the video connector please consult your computer or display card manual To obtain the MultiSync XV15 Macintosh cable adapter call NEC at 800 820 1230 For more details on connecting the MultiSync XV15 monitor to a Macintosh call FastFacts information at 800 366 0476 and request document 153006 For more information on FastFacts information please see page 20 To attach the MultiSync XV15 monitor to your system follow these instructions 1 Turn off the power to your computer and MultiSync monitor 2 If necessary install the display card For more information refer to the display card manual 3 For the PC Connect the MultiSync XV15 monitor s signal cable to the display card s connector on the computer Tighten screws on all connectors For the Mac Connect the MultiSync XV15 Macintosh cable adapter to the monitor s connector on your computer Connect the n XV15 monitor s signal cable to the other end of the cable adapter Tighten screws on all connectors A Connect one end of the power cable to the
13. arts are warranted for ninety 90 days e Who is Protected This warranty may be enforced only by the first consumer purchaser and is not transferable What is Covered and What is Not Covered Except as specified below this warranty covers all defects in material or workmanship in this Product The following are not covered by this warranty 1 Any Product which is not distributed in the U S A or Canada by NECTECH or which is not purchased in the U S A or Canada by the first consumer purchaser 2 Any Product on which the serial number has been defaced 3 Damage deterioration or malfunction resulting from but not limited to a Accident misuse abuse neglect fire water lightning or other acts of nature improper storage unauthorized Product modification or failure to Elev instructions supplied with the Product b Alteration repair or attempted repair by anyone not authorized by NECTECH c Any shipment of the Product claims must be presented to the carrier d Removal or installation of the Product e Any other cause which does not relate to a Product defect 4 Cartons carrying cases batteries external cabinets magnetic tapes or any accessories used in connection with the product 5 This warranty covers only NECTECH supplied components Service required as a result of third party components is not covered under this warranty What NECTECH Will Pay For and What We Will Not Pay For NECTECH will pay labor and mate
14. away from the screen e Is your monitor no closer than 12 inches and no further away than 28 inches from your eyes 18 inches is recommended e Do you use a document holder placed close to the screen For a detailed explanation on your monitor setup see page 14 78131481 18 7 29 98 8 44 AM TIT Checking You e Is your work area set up to promote a natural and relaxing working position with frequently used work items within close reach2 e Do you take frequent short breaks2 e Do you stretch and walk during your breaks e Do you vary your tasks during the day 78131481 19 i e Do you have regular eye checkups e Do you contact your doctor if you feel any sustained discomfort For more detailed information on workstation setup call NEC at 800 820 1230 NEC FastFacts information at 800 366 0476 and request document 900108 or write the American National Standard for Human Factors Engineering of Visual Display Terminal Workstations ANSI HFS Standard No 100 1988 The Human Factors Society Inc P O Box 1369 Santa Monica California 90406 Environment 7 29 98 8 44 AM Troubleshooting Support Troubleshooting Chart Problem m I KOR Check These Items No picture e The display card should be completely seated in its slot e Power Switch Degauss and computer power switch should be in the ON position e The signal cable should be completely connected to the display
15. ception This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult your dealer or an experienced radio TV technician for help If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402
16. e display card s scanning frequency displaying the resolution you desire The MultiSync XV15 monitor also supports multiple operating platforms such as PC compatible Macintosh family and workstation systems Increased refresh rates at all resolutions provide a flicker free image which is easier on your eyes and extends your viewing time Depending on the system used a wide range of graphics standards including VESA standards is supported by the MultiSyne XV15 color monitor for PC amp Mac including 640 x 480 60 to 120 Hz vertical refresh 800 x 600 55 to 103 Hz vertical refresh 832 x 624 55 to 97 Hz vertical refresh 1024 x 768 55 to 81 Hz vertical refresh 1280 x 1024 55 to 60 Hz vertical refresh Maximum resolution based on horizontal and vertical frequencies only NOTE Some systems may not support all modes listed Horizontal and vertical FullScan capability can increase the display size of a variety of video modes to the edges of the monitor bezel The FullScan capability allows you to use the entire screen area in most resolutions significantly expanding image size Introduction 78131481 9 7 29 98 8 44 AM Ka Controls Control Panel O O O O O GO 09 8 DO O Power SELECT RESET Q X Switch Degauss Brightness control SELECT Contrast control RESET Horizontal Adjustment controls position control Side pincushion control Vertical position contro
17. eaner to minimize dust e Adjust the monitor s brightness and contrast controls to en hance readability Use a document holder placed close to the screen Position whatever you are looking at most of the time the screen or reference material directly in front of you to mini mize turning your head while you are typing e Get regular eye checkups 7 29 98 8 44 AM m I eo Checking Your Comfort Checking Your Keyboard How Do You Measure Up e Is your keyboard angled so your wrists are straight when Use this checklist to see if you are setting up your work environ you type ment to fit your physical needs e Is your keyboard directly in front of you Checking Your Chair e Do you sit in an upright position with the backrest support s r ing your lower back BESET ist e When sitting are your feet flat on the floor e Do you avoid resting your wrists on sharp edges e Do you periodically adjust your chair and your posture e Do you press the keys gently and not bang on them 15 Environment 78131481 17 7 29 98 8 44 AM TIT KOR Be TIM Checking Your Mouse Checking Your Monitor e Is your mouse at the same height as the keyboard and next e Did you adjust your monitor so that the top of the screen is to the keyboard at or slightly below eye level e Are your wrists straight and your touch light when moving e Do you periodically rest your eyes by blinking often or the mouse looking
18. his document are warranted in accordance with the terms of the Warranty Statement accompa nying each product However actual performance of each such product is dependent upon factors such as system configuration customer data and operator control Since implementation by customers of each product may vary the suitability of specific product configurations and applications must be determined by the customer and is not warranted by NEC To allow for design and specification improvements the informa tion in this document is subject to change at any time without notice Reproduction of this document or portions thereof without prior approval of NEC is prohibited 78131481 27 i 7 29 98 8 44 AM TIT e non NEC Value Series NEC NEC Technologies Inc 1250 North Arlington Heights Road Part No 78131481 MultiSync is a registered trademark of NEC Technologies Inc Itasca Illinois 60143 1248 Printed in Singapore 78131481 28 7 29 98 8 44 AM TIT e non NEC Value Series NEC NEC Technologies Inc 1250 North Arlington Heights Road Part No 78131481 MultiSync is a registered trademark of NEC Technologies Inc Itasca Illinois 60143 1248 Printed in Malaysia 78131481 29 7 29 98 8 44 AM LA a av Printed on Recycled Paper MultiSync is a registered trademark of NEC Technologies Inc 78131481 30 Ka NEC Value Series NEC NEC Technologies Inc 1250 North Arlington Heights Road Itasc
19. in a natural and relaxed position Place items that you use frequently within easy reach Adjust your workstation setup to the proper height by lowering the table or stand that holds your computer equipment or raising the seat height of your chair To create more desk space you can put your computer base on the floor 13 Adjust your keyboard and mouse Na Adjust your monitor 78131481 15 7 29 98 8 44 AM Mi IEEE ie TIM Adjust Your Monitor Correct placement and adjustment of the monitor can reduce eye shoulder and neck fatigue Check the following when you position the monitor e Adjust the monitor height so that the top of the screen is at or slightly below eye level Your eyes should look slightly down ward when viewing the middle of the screen 78131481 16 e Position your monitor no closer than 12 inches and no further away than 28 inches from your eyes The optimal distance is 18 inches Rest your eyes periodically by focusing on an object at least 20 feet away Blink often Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections Adjust the monitor tilt so that ceiling lights do not reflect on your screen If reflected light makes it hard for you to see your screen use an anti glare filter Clean your monitor regularly Use a lint free non abrasive cloth and a non alcohol neutral non abrasive cleaning solution or glass cl
20. l Vertical Horizontal size control size control 78131481 10 7 29 98 8 44 AM Monitor Adjustment Controls SELECT Proceeds to the next control selection Moves the LED indicator light across the adjustment controls from left to right Horizontal position control left to right Adjusts the horizontal position of the image from left to right Vertical position control up and down Adjusts the vertical position of the image up and down Horizontal size control increase and decrease Adjusts the horizontal size of the image from wider to narrower Vertical size control increase and decrease Adjusts the vertical size of the image from taller to shorter Side pincushion control Adjusts the curvature of the edges of the left and right side of the display image either inward or outward The image should be adjusted to attain a straight line on the left and right sides Control Increases or decreases the adjustment of the selected control function RESET Resets image back to factory setting Contrast control Adjusts the image brightness in relation to the background Brightness control Adjusts the overall image and background screen brightness Power Switch Degauss Turns the power ON or OFF When the power is ON the LED power indicator above the Power Switch is lit This switch also acts as a Degauss Switch On power up the degauss circuitry eliminates stray magnetic fields that alter the correct scan of the e
21. lectron beams and affect the purity of the screen colors the focus and misconvergence Controls 78131481 11 7 29 98 8 44 AM m tTTT 10 Monitor Specifications Ka MultiSync XV15 Notes Picture Tube Diagonal 15 0 inch 90 deflection 0 25 mask pitch medium short Viewable Image Size 13 8 inch persistence phosphor CROMACLEAR CRT Radius 1080 mm anti static screen coating semi tint screen and OptiClear screen surface Input Signal Video ANALOG 0 7 Vp p 75 Ohms Positive Sync Separate sync TTL Level Horizontal sync Positive Negative Vertical sync Positive Negative Composite sync Positive Negative TTL Level Display Colors Analog input Unlimited Number of Colors Dependent upon display card used Synchronization Horizontal 31 kHz to 65 kHz Automatically Range Vertical 55 Hz to 120 Hz Automatically Maximum Resolution 1280 x 1024 60 Hz Maximum resolution based on horizontal and vertical frequencies only Resolutions Supported 78131481 12 640 x 480 60 to 120 Hz 800 x 600 55 to 103 Hz 832 x 624 55 to 97 Hz 1024 768 55 4018 HZ vi ormene 1280 x 1024 55 to 60 Hz Ka Some systems may not support all modes listed NEC cites recommended resolution at 75 Hz for optimal display performance Ka Be TIM Monitor Specifications MultiSync XV15 Notes Active Display Area Factory Setting 260 x 195 mm Dependent upo
22. n signal timing used and does not 10 2 x 7 7 inches include border area Active Display Area Full Scan 280 x 210 mm Dependent upon signal timing used and does not 11 0 x 8 3 inches include border area Power Supply AC 100 120 V 50 60 Hz Current Rating 1 8 Amps Dimensions 372 mm W x 389 mm H x 414 mm D 14 6 inches W x 15 3 inches H x 16 3 inches D Weight 15 6 kg 34 4 Ibs Environmental Operating Temperature 0 C to 35 C 32 F to 95 F Considerations Humidity 30 to 80 Feet 0 to 10 000 Feet e Storage Temperature 20 C to 60 C 4 F to 140 F Humidity 10 to 90 Feet 0 to 45 000 Feet NOTE Technical specifications are subject to change without notice 11 Specifications 13 78131481 7 29 98 8 44 AM Fa RECO ended Use For optimum performance please note the following when e The power cable connector is the primary means of detaching the setting up and using the MultiSync XV15 color monitor system from the power supply The monitor should be installed close to a power outlet which is easily accessible e If possible position the monitor so that it is facing east to minimize the effects of the earth s magnetic field e Clean the monitor with a lint free non abrasive cloth and a non alochol neutral non abrasive cleaning solution or glass cleaner e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not put a
23. nything on top of the monitor e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Changing the direction the monitor is facing while it is powered on may cause image discoloration To correct this turn the monitor off for 20 minutes before powering it back on e Keep the monitor away from high capacity transformers electric motors and other devices such as external speakers or fans which may create strong magnetic fields e Use the monitor in a clean and dry area e Handle with care when transporting Save packaging for transporting 78131481 14 7 29 98 8 44 AM m I eo Be TIM Setting Up a Healthy Work Environment Making Your Computer Work For You Computers are everywhere More and more people sit at computers for longer periods of time This section explains in detail how to set up your monitor to fit your physical needs along with a general explanation on setting up your workstation For a complete detailed explanation on setting up a healthy work environment call NEC at 800 820 1230 NEC FastFacts information at 800 366 0476 and request document 900108 or write the American National Standard for Human Factors Engineering of Visual Display Terminal adjust gt Workstations ANSI HFS Standard No 100 1988 your char The Human Factors Society Inc P O Box 1369 Santa Monica CA 90406 Arrange Your Equipment Arrange your equipment so that you can work
24. reduces the reflection and glare of ambient lighting resulting in greatly improved user comfort and productivity This multilayered screen coating increases the contrast without sacrificing the focus level clarity or brightness A high contrast screen with a 0 25 mm mask pitch sharpens image clarity and enhances detail On screen information is easier to read The flat square CRT technology reduces image distortion and glare Plug and Play Plug and Play is the new Microsoft solution with the Windows 95 operating system to provide automatic peripheral connections without confusing and time consuming setup When used with a Plug and Play compatible system and display card the MultiSync XV15 monitor automatically tells the system its identification and capabilities The system will then select its highest resolution and refresh rate to take advantage of your MultiSync monitor 7 29 98 8 44 AM ErgoDesign Features ErgoDesign features enhance human ergonomics human and earth conditions which will improve the working environment protect the health of the user and save money ErgoDesign features parallel the strict European standards of power management and reduced emissions and the requirements laid down in the TCO Swedish Confederation of Professional Employees Agreement on Environmental Labeling 1992 Power Manager IPM Intelligent Power Manager System is an innovative power saving feature that complies with both the EPA
25. rial expenses for covered items but we will not pay for the following 1 Removal or installation charges modified or removed 21 78131481 23 7 29 98 8 44 AM 22 2 Costs of initial technical adjustments setup including adjust ment of user controls 3 Payment of shipping and related charges incurred in returning the Product for warranty repair How You Can Get Warranty Service You have the option of returning this Product to a NECTECH authorized service center or directly to a NECTECH factory for repair It shall be your obligation and expense to ship the Product freight prepaid or to deliver it to a NECTECH authorized service center or other facility authorized by NECTECH to render the warranty services in either the original package or a similar package affording an equal degree of protection NECTECH may require that you provide the original bill of sale or receipt as proof of purchase in order to obtain warranty service Please retain such proof of purchase with your records Limitation of Damages and Implied Warranties NECTECH S SOLE LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR OPTION NECTECH SHALL NOT BE LIABLE FOR 1 DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THIS PRODUCT DAMAGES BASED UPON INCONVENIENCE LOSS OF USE OF THE PRODUCT LOSS OF TIME OR DATA COMMERCIAL LOSS OR 2 ANY OTHER DAMAGES WHETHER INCIDENTAL CONSEQUENTIAL OR OTHE
26. tor and the other end to a power outlet Turn on the monitor Turn on the computer y If necessary use the front panel controls to adjust the image to personal preference 7 29 98 8 44 AM Quick Start See the Troubleshooting section No A Is the image correct The installation of your MultiSync XV15 monitor is finished Enjoy your monitor Connection To Your Personal Computer The MultiSync XV15 color monitor complements NEC computers PC compatibles Macintosh and Macintosh compatibles For the PC Your system has one of two configurations the video controller is built into the computer the video controller is in the form of a display card sometimes referred to as the graphics card video adapter or graphics board Both configurations have a video connector or a CRT PORT on laptop computers If you are not sure which port is the video KOR connector please consult your computer or display card manual For the Mac With the MultiSync XV15 Macintosh cable adapter the MultiSync XV15 color monitor is compatible with Macintosh computers as well as Macintosh clones NOTE Power Macintosh 6100 60 and 66 users need to use the Apple HDI 45 cable adapter and Powerbook users need to use the VID 14 cable adapter in conjunction with the appropriate MultiSync ae adapter when connecting a MultiSync monitor The MultiSync XV15 Macintosh cable adapter allows you to ch
27. trademarks or registered trademarks of their respective owners The Energy Star emblem does not represent EPA endorsement of any product or service 78131481 3 Ka Contents Troubleshooting Support Troubleshooting Chart FastFacts Information Technical Support The BBS Electronic Channels Warranty References Directory of Telephone Numbers 7 29 98 8 44 AM TIT Contents of Package Congratulations on your purchase of a MultiSync XV15 color monitor 2 The following lists all of the items included with your MultiSync color monitor package 1 MultiSync XV15 color monitor JC 1571VMA 2 with tilt swivel base Power cord Captive signal cable User s manual Registration card Please fill out and return this card as soon as possible aAkWN Remember to save the original box and packing materials to transport or ship this monitor 78131481 4 7 29 98 8 44 AM Yes Is the monitor a MultiSync XV15 monitor 78131481 ls the computer a Macintosh computer Call NEC at 800 820 1230 to receive your MultiSync XV15 Macintosh cable adapter NA adapter to the monitor connector on the Macintosh Attach the Mac Tighten the screws Ka Attach the monitor5 signal cable to the display card or adapter on your computer Ka Connect one end of the power cable to the MultiSync moni
Download Pdf Manuals
Related Search