Precision counting Scale
Contents
1. keys to add or clear accumulated times and total count 1 Press key after total count has been calculated and displayed The display will show the accumulated times in the Total Weight display X X X represents the total accumulated times a maximum of 99 accumulations can be accepted The display will show OL when the accumulated count are more than 999999 and total quantity in the Unit Weight display 2 Press Key to clearthe stored data IX Selection of Filter parameter While the scale is used in a different location changing the response speed could be desired You can change the STABLE time and the stability of the scale by setting the filter parameter Pressand hold key and tum the scale ON untilthe end of self test the display will show the current filter parameter Presh key again to change Pressthe key Poy to confirm 4 Nb X representsa classof filter parameters and the larger X is the fasterrespond speed is X Zero tracking range and Zero display range 1 Selection of Zero tracking range Tum the scale ON then pressand hold 0 until the end of the self test 0 0d or 0 5d 1 0d 1 5d 2 0d 3 0d will be displayed Press gt to change press Pod to confirm 2 Selection of Zero display range Afterselecting Zero tracking range it will display Zero S invalid or Zero L 0 is displayed when the weight is within 3d range Press lt gt2. key to change press od to confirm 3 Select whether 0 will be shown when the weight is within 30d 0 0d Pressley Select 30d OFF or 30d ON press boy to confirm XI Division Selection Tum the scale ON then press and hold key until the end of the self test the display will show the selected division Press key to change and press fog to confirm XII Counting and Auto average Tum the scale ON Press amp hold 3 until the end of self test div will be displayed counting division or Code counting ISN Press key to change press o4 to confim Next the display will show OFF tum auto average off or ON 5
3. Precision counting Scale Model NO CTS5 3000 C T5 6000 Operation Manual CTS 3000 6000 en V5 0 2006 TABLE OF CONTENTS I Overview 1 II Precautions Before Using The Scale 1 III Keypad Functions 2 IV Operations 2 calibration is end Extemal calibration will not work when the enor is outside the range of 10 of Max Capacity XVI Recharging the battery When the battery voltage is low the LOW POWER indicator will be shown Please tum the scale off and then fully recharge it otherwise the scale will automatically tum off When recharging a yellow LED will light up on the panel It will tum RED when fully charged lt takes approximately 12 hours to fully charge the battery To ensure the battery voltage is in full we recommend charging an extra 3 4 hours I Overview The CTS series electronic counting scale uses high precision sensors and the latest Microchip technology It is specially designed and manufactured for accurate weighing and counting functions This manual is a guide and subject to change or corection Please check our website for the most recent operation manual or notes II Precautions Before Using The Scale 1 Do not let the scale get wet and do not place it in an environment with extre me temperature or humidity 2 Do not shock the scale and do not exceed the
4. Press Ss to change and press bos to confirm RS 232 Communication format Baud Rate 2400 4800 9600 Data Bit 8 Parity N None Stop Bit 1 Code ASCII Data Format normal weighing mode Il Power off Push the switch to OFF to tum the scale OFF III Zero function Zero range 2 of max capacity press o4 key to retum the display to zero in case there is any zero drifting with nothing on the tray IV Tare function Place the container on the pan press fe key to subtra ct the containers weight When the displayed number is stable lt gt will be shown Remove the container the display will show the grossweight companied by a negative sign Press the Tare key again to cancel Tare mode V Unit weight setting A known unit weight can be inputed directly by entering the value first then followed by pressing 5 key VI Unit weight by sampling 1 Put the objects intended for sampling on the pan 2 Input the number of the objects this number will blink in the Unit Weight displa y 3 Press Key the calculated unit weight will then be shown in the Unit weight displa y the total quantity will then be displayed VII Counting check Users can set a number for counting check when the numberof objectson the pan islargerthan the preset checking number the alarm will beep repeatedly Set Enterin the desired checking number then press key 4 Clear Press key VIII Accumulation Use ba
5. capacity Permanentdamage can occur 3 If the power is low or the scale automatically power off please charge the battery for a full 12 hours before use Incomplete charging can damage the battery 4 Before using the scale place it on a stable platform and adjust its feet to make the scale level 5 Working conditions 1 The operating temperature should be 0 C 40 C 2 Power supply AC 220V 10 or DC 6V1 5A h NiH battery III Keypad Functions G GROSS N NET 0 9 Numeric keys 1 2 B 4 5 6 7 8 9 joz 12 13 1415 16 117 18 HEAD DATA UNIT CR Decimal point key G N Wil i H K lg CRILF If there isa minor weight displayed without anything on the pan hitthe zero key to clearthe display HELD DATA UNIT CR Use this key to subtract the containers weight Indicate that the current weight reading is net Y QUE i 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 weight HELD DATA UNIT CR gt M gt This key is used fortotal count accumulation Tlo t a l p c s CR LF Use this key to clearthe total count accumulation EXAMPLE G W 1009 UW 0 2g pcs Use this key for checking the number entry Total 500pcs confirmation Use this key to eliminate the count check entries XV External Calibrati
6. on Use this key to clearthe readingsentered When the scale does not read accurately you may calibrate it with weight Tum the scale on pressand hold until the end of self test Used when manually keying in the unit weight Sample Key Used when keying in a sample amount F 0 FEBO It will show CAL Press Poy to show 0 place a weight IV Operations 2 3 of the Max Capacity is recommended on the tra y input 1 Power on the value of the weight via numeric keys The unit is kg Ex The Max Capacity is 3kg the weight should be 2kg then enter 2 Remove all objects from the tra y push the switch to ON to after stable press os to confirm the entered Now the tum the scale ON The scale will self test and then go to 2 7 tum auto average on Press e key to change press pod to confirm XIII Setting backlight Tum the scale ON Press and hold 1 until the end of the self test the display will show AUTO AUTO backlight or OFF disable backlight or ON Backlight is ever lighting Press gt key to altemate press bos to confirm XIV Setting of communication optional Tum the scale ON press and hold 2 unitl the end of the self test it will display the Baud Rate preset select one 2400 4800 or 9600 by pressing confirm it by pressing fog Enter the selection of communication modes select one ST output when the reading isstable Co continue output
Download Pdf Manuals
Related Search