ild user manual rev. 1
Contents
1. a IL ILD dimensions 258 mm 10 2 in All dimensions in mm Drawing not to scale ILD USER MANUAL REV 1 2012 SGM Information subject to change without notice SGM and all affiliated com panies disclaim liability for any injury damage direct or indirect loss consequential or economic loss or any other loss occasioned by the use of inability to use or reliance on the information contained in this manual The SGM logo the SGM name and all other trademarks in this document pertaining to services or products by SGM or its affiliates and subsidiaries are trademarks owned or licensed by SGM or its affiliates or subsidiaries English edition Contents Ale ie aa do y APA UU o PO II E 6 E o E E E a R 8 installing o A E A T eee ee 9 Connecting DOWN ii ide tadas 11 Connecting to control Uan ba 12 Configuring Me deis 14 SEIN OO o ersehen ee 16 Safety information WARNING Read the safety precautions in this section before installing powering or operating this product The ILD is intended for professional use only It is not suitable for household use Review the following safety precautions carefully before installing or operating the device Preventing electric shock N DANGER Risk of electric shock Do not open the device Do not open the device there are no user serviceable parts inside Ensure that po2. ofall DOWER Consumption rotor 150 W Specifications subject to change without notice 18 19 SGM A S Soeren Frichs Vej 51 53 DK 8230 Aabyhoej Denmark Tel 45 70 20 74 OO info sgmlisht com www sgmlisht com
3. ain using the Artnet out socket Do not daisy chain more than five ILDs or O other driver devices from a single network port or computer and use an Ethernet switch if more than five ILDs are being configured and controlled PC Laptop Controller For communication to function both the ILD and the PC must be on the same local area network LAN with IP addresses in the 2 x x x range which are IP addresses used and recognised by Artnet The PC can be connected directly to an ILD using a network Ethernet cable and up to ILDs can be daisy chained To connect more than five ILDs use an Ethernet switch but do not connect more than five ILDs to each port Configuring the device Configuring the device using the SGM Artnet Configurator Once pixel luminaries are attached and the ILD is connected to AC power setup the ILD using the SGM Artnet Configurator available from http www sgmlight com See the SGM Artnet Configurator User Manual The SGM Artnet Configurator in a Windows based application for configuring and addressing SGM Artnet pixel drivers such as the ILD The SGM Artnet Configurator can be used to configure the ILD and assign DMX addresses with three DMX channels red green and blue to each pixel The ILD can be configured to address pixels across multiple DMX universes A highlight function enables testing of the configuration and power measurements are shown This is useful for troubleshooting if too
4. er pressure jets of water from any direction Installing the ILD WARNING Always secure an elevated ILD with a safety cable as backup The ILD may be installed in any orientation Before installing ILDs at elevation ensure that the Attachment hardware is in good condition and designed to support at least 10 times the fixture s weight Structure can support at least 10 times the weight of all installed fixtures Work area below is blocked from public access and make sure the work is performed from a stable platform When using more than one ILD to create an LED curtain ensure that the ILDs are installed so that the correct pixel pitch can be achieved A T Bolt Bracket is available to support an ILD when bolted to a surface For other mounting solutions consult your SGM representative T bolt Bracket 146 mm 5 7 in 18 mm 4 6 in Ea 10 gt 76 mm 3 0 in Use two T Bolt Brackets to attach an ILD to a flat surface These brackets are secured to the mounting surface using three pieces of M6 hardware To attach an ILD to a bracket slide the t bolts into the attachment rail in the ILD casing A turn the bolt 90 degrees so that its head is under the rail rim and then secure by tightening the nut B 90 mm 3 5 in C4 Ss O 35 mm 1 4 in 6mm OS G0 2x in 35 mm 1 4 in un o e ho 4 a gt vv Connec
5. many pixels are attached performance issues can occur as an ILD may not supply more than 150 W AdvancedControl e 4 Enable advanced control 2 16 3 222 SGMILD Board temperature N A c Power consumption 6 8 W Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Fixture LT 100 m00 Y LT 200 y LT 100 Y 11 100 y 11 100 y DMX Address 1 827 163 7 244 3257 406 Universe 3 7 3 9 B 9 7 8 8 Y Highlight 4 Highlight 4 Highlight Highlight Highlight Highlight Upload Firmware Close 14 Configuring the device using an Android telephone via RFID As an alternative to connecting the device to power and using the SGM Artnet Configurator one or more ILD devices can also be configured wirelessly via RFID using the SGM Tool app available from the Google Play Store installed on an Android smart phone that has NFC support ISO 15693 and ISO 18000 3 mode 1 compatible operating on 13 56 MHz 7k Hz carrier frequency 15 Service There are no user serviceable components inside the device Do not open the ILD as doing so is likely to damage its ingress protection Consult your SGM dealer if the device operates abnormally is defective or otherwise in need of service or repair Upgrading the firmware We recommend that you to keep your device s firmware current Visit http www sgmlight com to obtain the most up to date firmware To perform firmware updates you need a Windows personal computer and the SGM Artne
6. t Configurator available from http www sgmlight com 16 Specifications PHYSICAL Length x Width X height 2s lt lt sccsccescaceescencescreas ers 299 x 116 x 65 mm 11 8 x 4 6 x 2 6 in CONSTRUCTION PIOUS ING NN Steel a A A A caiaaaies paunassiesaccaisnie a ceuceeeaacapoqesissteastuabsa ceteenus Black INSTALLATION Orientation euere ads Any AMBIENT OPERATING CONDITIONS Maximum ambient temperature T ococoocononconanonoonononnononnanononnononnonononnonnnnononnnnnn nono nnnnnnnn nens non nnnrnnennnnnnnno 40 C 104 F Minimum ambient temperature T Jesas EKNE Eaua KNEA 10 C 14 F Operating humidity oran ia EE E ETEN 100 IP rating are A E e EE a E IP 65 17 PROGRAMMING AND CONTROL CONTQUIAION sgte trotar irneda via PC running SGM Artnet Configurator Control of attached LED pixelS 220u0424400nnnnnnnnnnnnnnnnnannnn via Artnet with three DMX channels per LED pixel Software upgrade u 22400nn24snnnnnnnnnnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnannn via PC running SGM Artnet Configurator Wireless interface via RFID using an Android telephone that has NFC support and SGM Tools app CONNECTIONS Armetdata Input sons d ralla RJ 45 female socket Arinet datavoutput id RJ 45 female socket Pixel luminaire connections Six threaded screws compatible with SGM LT 100 LT 200 and LED Balls ELECTRICAL AC POW odos 100 240 V 50 60 Hz Maximum
7. ting AC power The ILD can operate on any 100 240 V 50 60 Hz AC mains power supply For temporary installations install a grounding type earthed industrial 3 pronged type B plug that complies with IEC 60309 or a comparable national standard and is rated 16 A minimum and use corresponding power outlet sockets Follow the connector manufacturer s instructions and all locally applicable laws and electrical safety codes For permanent installations have a qualified electrician hard wire the ILD to the AC mains supply The device must be grounded earthed and be able to be isolated from AC power The AC power supply must incorporate a fuse or circuit breaker for fault protection Connecting LED pixels The ILD is able to drive six SGM LT 100s three SGM LT 200 or 168 6 x 28 SGM LED Ball pixel luminaires These can be attached in any arrangement to the six connectors on the ILD The six LED pixel connectors on the ILD are not design to bear loads Always ensure that any attached LT 100s LT 200s and LED Balls are supported by other means than attachment to an ILD connector 11 Connecting to control data eg Artnet out The device complies with the Artnet communications protocol lt must be connected to an Artnet compliant LAN IP addresses in the 2 x x x range Connect the Artnet in socket to the Artnet E ek compliant LAN using an Ethernet cable with an RJ 45 connector The ILD can feed control signals to another device in a daisy ch
8. wer is cut off when wiring the device to the AC mains supply Ensure that the device is electrically connected to earth ground Do not apply power if the device is in any way damaged Do not immerse the fixture in water or liquid WARNING Take measures to prevent personal injury Install only in a well ventilated space Do not paint cover or modify the device Take precautions to prevent injury due to falls when working at height Ensure that the device is always securely fastened with suitable hardware For elevated installations always comply with relevant load dimensioning and safety standards and requirements Overview The ILD is an Artnet pixel driver that can be used to drive six SGM LT 100s three SGM LT 200 or 168 SGM LED Ball pixel luminaires Up to five ILDs can be configured and controlled when daisy chained together and connected to a computer using an Ethernet cable and up to five ILD s per port can be daisy chained when one or more Ethernet switches are used ILDs can be configured using the SGM Artnet Configurator available from http www sgmlight com and controlled using a lighting controller or computer based Artnet controller Unpack the device and inspect it to ensure that it has not been damaged in transport The fixture is not designed for permanent outdoor installation but it is IP65 rated This means that it is protected from Dust to the degree that there is no ingress of dust Low
Download Pdf Manuals
Related Search