LZ500 Green Laser User Manual Safety Information
Contents
1. 12500 Green Laser User Manual Thanks for purchasing LZ500 Green Laser Please read this manual carefully and thoroughly as it gives important information regarding safety and operation instruction Keep this manual in order to consult it in the future The quality of every set of the products is guaranteed in the factory before the shipment Please check the accessories as the packing list inside If the carton appears to be damaged please inspect the fixture carefully In case damage has been found or some parts are missing please contact Neo Laser after service department before shipping back the product Safety Information Always ground the fixture electrically properly 2 For indoor use only Keep in cool and dry place with the ambient temperature of 10 35 C Put the fixture in steady place and do not shake 3 Continuous operation of over 4 hours will shorten the life of the laser Please always keep within 4 hours 4 The lens at the aperture will be covered with dirt and dust that will decrease the power output Please clean it with the soft cloths or paper periodically 5 Do not attempt to tear off the warranty paper Such action will avoid the company s warranty 6 Do not attempt to dismantle the fixture if problems happen Please connect with Neo Laser after service department directly 7 Do not throw away the packing material If problems happen please pack the product with the material and send back to Neo2. 351 383 415 447 479 511 Dip Switch Position Address
3. 482 1 1 o 0 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483 o O 1 o 4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484 1 1 o 5 37 69 101 133 165 197 229 261 293 325 357 389 421 453 485 1 1 o 6 38 102 134 166 198 230 262 294 326 358 390 422 454 486 1 1 1 o 7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487 1 0 8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488 1 1 0 9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489 1 o 1 0 10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490 1 1 1 0 11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491 1 0 12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492 1 1 1 0 13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493 o 1 1 1 0 14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494 1 1 1 1 0 15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495 oma 16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496 1 17 49 81 113 1
4. 37 EG Each projector is distributed with 16 DMX channels ADDR 17 ADDR 49 ADDR 1 ADDR 33 Loop2 Loop4 Loop1 Loop3 Address Setting In binary system there are only two number increase by multiplying the previous value by 2 Positions from dipswitch 1 to dip switch 9 signify binary value from lower to high position 0 meaning OFF and 1 meaning EG LOOP ADDR BINARY 1 1 100000000 2 17 100010000 3 33 100001000 DMX control table Channel Function DMX Value Detail 0 30 Laser Off 31 100 DMX CH1 Mode Selection 101 175 Auto 176 255 Sound Active CH2 Pattern Selection 0 255 35 patterns CH3 X Position 0 255 Pan CH4 Y Position 0 255 Tilt Size from small to CH5 Scan Size 0 255 big Speed from fast CH6 Scan Speed 0 255 to slow Operation DMX ADDRES S MATHEM ATICAL RIDDLE ADDR The numbers Note via DMX only CH3 amp 4 are valid in Auto amp Sound Active Mode Genera 1 Mode settings Based on different application different modes are set If in DMX mode bear in mind the correct DMX address assignment 2 Connection connect the projector and DMX 512 console with the DMX signal cable As for Stand Alone there is no need 3 Powered on laser emits the beam in 2 seconds 4 The projector can be controlled to play and edit shows by DMX512 console in DMX mode by default program in auto mode and in sound active mode if soun
5. Laser after service department LASER RADIATION A OID EXPOSURE TO BEAN 1 55 LASER PRODUCT 2 _ Fuse Replacement Note replace the fuse with the same specified If not the potential damage will be avoided of the company s responsibility Replace the fuse Disconnect the power use the screwdriver to unscrew the fuse holder take out the fuse place it with the good one of the same specified and finally screw the fuse tight Technical Specification AC Power AC 110 V 220V 50 60 HZ Fuse 2A Laser Wavelength 532nm Verdure Facula Size 12 Power 10mW Control system high capacity macro processor Scanner step motor X Y scanning Display Mode DMX Sound Active Auto 1 ar WD Laser Safety Level Class IIIB Connector 3 pin DMX Connector XLR Net Weight KG Size 280MM 206MM 163MM LxWxH ON OD Function Introduction 1 SOUND ACTIVE The laser graphic is controlled by with the sound that is the graphic effect changes with the rhythm Turning the sensitivity knob in a clockwise direction will increase the sound sensitivity Turning the sensitivity knob in a counter clockwise direction will decrease the sound sensitivity Only the medium and low frequency that reaches certain sound intensity can control the changing effect of the graphic Without sound activation for 7 seconds the system shuts out the laser 2 AUTO The laser graphics runs automatically by the built in programs Via Auto mod
6. 45 177 209 241 273 305 337 369 401 433 465 497 o 1 mm o i 18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498 1 1 mm o ii 19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499 iit 1 20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500 1 o 1 i 21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501 o 1 1 1 22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502 1 1 1 1 23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503 ROMI 1 1 24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504 1 lo 1 1 25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505 o 1 o 1 1 26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506 1 1 1 1 27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507 iit 1 1 28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508 1 o i 1 1 29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509 o 1 1 1 1 30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510 1 1 1 1 1 31 63 95 127 159 191 223 255 287 319
7. d sensitivity knob is kept in proper position M S mode 1 Stand Alone Via MASTER_ SOUND or MASTER_ AUTO no console is needed Laser shows only obey sound or default program 2 Mode settings set the dipswitch in corresponding position that is MASTER_ SOUND 10 0 11 0 12 0 MASTER_ AUTO 10 0 11 0 12 1 SLAVE 10 0 11 1 12 1 3 Connection Use XLR XLR cable to connect the Masters DMX output with the DMX Input of the first Slave and then output of the first Slave with input of second Slave till all the Slaves are connected in this way 4 Powered on laser emits the beam in 2 seconds 5 The projector can be controlled to play shows by default program in Auto mode and in MASTER _ SOUND mode if sound sensitivity knob is kept in proper position Note 1 Via Master Slave mode there should be only one Master and no DMX512 controller 2 Power on the Master and the Slaves at the same time or first power on the Slaves then the Master SLAVE 2 51 1 MASTER Sound Auto MASTER SLAVE Connection DMX Mode 1 Use standard DMX512 console in DMX Mode 2 Mode settings set th
8. e the laser cannot be shut off automatically 3 DMX control The system only accepts the DMX 512 control DMX control can control the laser s on off the graphics and its size color direction scan speed and display speed etc Function Settings 4 Work Mode 1 SOUND ACTIVE triggered by sound only 2 AUTO_MODE default program not subject to change with the external effect 3 SLAVE controlled by Master only receive Master s data Note only one master no link with console 4 DMX MODE controlled by DMX 512 console only receive console s data Set the system function with the dipswitch See the function listed below 1 The dipswitches 10 11 and 12 are for the setting of the system function The dipswitches 1 9 are for the setting of the DMX Channel Address in DMX mode If not in DMX mode the dipswitches 1 9 can be set randomly 2 The setting of the projector s address is needed via DMX mode Under control of DMX 512 console the projector takes up 9 channels Dip Switch Setting O OFF 1 ON X OFF or ON DIPSWITCH CHART FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 ND X X X X X X X X X 0 0 0 AUT X X X X X X X X X 0 0 1 MODE DMX SET DMX ADDRESS 0 1 0 MODE X X X X X X X X X 0 1 1 SLAVE X N 1 CH_NUM DMX CHANNEL OF THIS PROJECTOR CH_NUM gt 9 N PROJECTOR CHANNEL NUMBER N 0 1 2
9. e dipswitch in corresponding position that is DMX Mode 10 0 11 1 12 0 3 Connection Use XLR XLR cable to connect DMX 512 console with the DMX Input of first projector and then output of the first projector with input of second projector till all the projectors are connected in this way 4 Powered on laser emits the beam in 2 seconds 5 Console control N DMX 2 DMX 1 DMX DMX Connection Accessories 1 User Manual 1PCS 2 Handle 1PCS 3 DMXcable 1PCS 4 Power cable 1PCS Trouble Shooting Problems Reasons Remedy Power indicator off Check if AC power matchesiMake sure of the specified power or and no laser specified check the power facility Via stand alone mode power indicator on no Set to Slave mode by mistake Set Stand alone Sound Active of Stand alone model abnormally Via DMX mode DMX laser Slave projector works 2 indicator off and laser Stand alone Auto The mode setting only 1 the work mode properly Master with others set asi2 Disconnect with the DMX signal M S mode Slave 3 Make sure of the connection Check if there is DMX console or not Check the connect
10. ion between Master and Slaves Check if the work mode is set to DMX mode Check the XLR XLR cable s connection and quality 4 Make sure of the XLR XLR between Master and Slaves 3 Set the work mode to DMX mode properly cable s connection and quality indicator flicker DMX mode sure the DMX console s channel distribution match with the but out of control of thellaser s Set the channel distribution and the laser s DMX address again console Some patterns Power on again and the system blocked regain normality other problems please contact your distributor or service Dept of Neo Laser DMX Address Quick Reference Chart Dip Switch Position DMX DIP SWITCH SET 0 o o o 0 0 0 0 1 1 1 1 1 1 1 1 810 o o 1 1 1 1 0 0 0 0 1 1 1 1 1 ON 7 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X OFF or ON 6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 2 3 4 5 o jo jo fo 32 64 906 128 160 192 224 256 288 320 352 384 416 448 480 1 ROm o 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481 1 o o 2 34 66 98 130 162 194 226 258 290 322 354 386 418 450
Download Pdf Manuals
Related Search