Home

1971.4KB - Axiomtek

1. AK AXIOMTEK SHB110 Series Intel Core 2 Duo Core Duo Core Solo PICMG 1 3 Full Size Single Board Computer User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document AXIOMTEK does not make any commitment to update the information in this manual AXIOMTEK reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd CAUTION If you replace wrong batteries it causes the danger of explosion It is recommended by the manufacturer that you follow the manufacturer s instructions to only replace the same or equivalent type of battery and dispose of used ones Copyright 2008 AXIOMTEK Co Ltd All Rights Reserved May 2008 Version A3 Printed in Taiwan ESD Precautions Computer boards have integrated circuits sensitive to static electricity To prevent chipsets from electrostatic discharg
2. On Chip Secondary PCIIDE Enabled IDE Secondary Master PIO Auto IDE Secondary Slave PIO Auto IDE Secondary Master UMDA Auto IDE Secondary Salve UMDA Auto H your IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support On Chip Serial ATA Auto Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults Fr Optimized Defaults gt IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support gt IDE DMA transfer access Automatic data transfer between system memory and IDE device with minimum CPU intervention This improves data throughput and frees CPU to perform other tasks gt On Chip Primary Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately The default value is Enabled W SA NOTE Choosing Disabled for these options will Phoenix Award BIOS Utility 41 SHB110 Socket M Full Size SBC User s Manual automatically remove the IDE Primary Master Slave PIO and or IDE Secondary Master Slave PIO items on the
3. Port Drive Model Serial Size Type Status Vol ID ST380815AS 60221RYL 74 5GB mber Disk 0 2 ST3808110AS 4LR1S469 74 5GB Press lt CTRL I gt to enter Configuration Utility Select ESC Exit ENTER Select Menu Figure 10 Please press ESC to exit the ICH7MR RAID BIOS utility Now you can proceed to install a SATA controller and the operating system 4 Making a SATA Driver Disk To install the operating system onto a serial ATA hard disk successfully you need to install the SATA controller driver during the OS installation Without the driver the hard disk may not be recognized during the Windows setup process First of all please format a blank floppy disk Secondly follow up these steps below to produce a SATA driver disk 4 1 76 Users can insert the Driver CD and the formatted blank floppy disk in another system And then please execute the f6flpy32 exe file in the folder of the Driver CD Note Please execute the f floy64 exe file if installing 64 bit Windows Operating System totlpy32 exe Configuring SATA for RAID Function SHB110 Socket M Full Size SBC User s Manual 4 2 When this screen pops out please click the CONFIRM button Hatch assistant i J Is floppy to write Configuring SATA for RAID Function 77 SHB110 Socket M Full Size SBC User s Manual 4 3 When the Driver is written to the floppy disk the SATA driver disk is completed Formatting and
4. SHB110 Socket M Full Size SBC User s Manual Intel Chipset Device Software Intel Chipset Device Software Setup Progress Please wait while the Following setup operations are performed Installing Driver Intek R ICHS Family USE Universal Host Controller 2834 Version 8 0 0 1008 Installing Driver Intel R ICHS Family USB Universal Host Controller 2635 Version 5 0 0 10068 Installing Driver Intel R ICHS Family USB2 Enhanced Host Controller 2836 Version 8 0 0 1008 Installing Driver Intel R ICHS Family USB2 Enhanced Host Controller 2634 Version 8 0 0 1008 Glick Next to continue Intel Chipset Device Software Setup Is Complete The setup program successfully installed the Intel Chipset Device Software onto this computer Click Finish to complete the setup process Installation of Drivers St SHB110 Socket M Full Size SBC User s Manual 5 You will be asked to reboot your computer when the installation is completed Please click Yes want to restart my computer now if you don t need to install any other drivers Otherwise please click No will restart my computer later and go on next step 6 2 Installing VGA Driver 1 Run the SETUP EXE program from the driver directory in your driver CD Click Next to next step Intel R Graphics Media Accelerator Driver Life Intel Graphics Media Accelerator Driver Welcome to the setup for the Intel R
5. of devices using the interrupt 1 Legacy ISA Devices compliant with the original PC AT bus specification requiring a specific interrupt such as IRQ4 for serial port 1 2 PCI ISA PnP Devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture The default value is PCIISA PnP e PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This item allows you to set whether MPEG ISA VESA VGA Cards can work with PCI VGA or not When enabled a PCI VGA can work with a MPEG ISA VESA VGA card when disabled a PCI VGA cannot work with a MPEG ISA VESA Card PCI Express relative items e Maximum Payload Size When using DDR SDRAM and Buffer size selection another consideration in designing a payload memory is the size of the buffer for data storage Maximum Payload Size defines the maximum TLP Transaction Layer Packet data payload size for the device Phoenix Award BIOS Utility 49 SHB110 Socket M Full Size SBC User s Manual 5 11 PC Health Status This section supports hardware monitering that lets you monitor those parameters for critical voltages temperatures and fan speed of the board AwardBlOS CMOS Setup Utility PC Health Status Phoenix Item Help Menu Level gt Move Enter Select PU PD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults Fr Optimized Defaults e Current CPU Temper
6. SHB110 Socket M Full Size SBC User s Manual After the creation is completed you can see detailed information about the RAID Array in the DISK VOLUME INFORMATION section including RAID mode disk block size disk name and disk capacity etc Intel R Matrix Storage Manager option ROM v5 7 0 1007 ICH7MR Copyright C 2003 05 Intel Corporation All Rights Reserved MAIN MENU l Bal Ki IUTE 2 Delete RAID Volume 3 Reset Disks to Non RAID 4 Exit DISK VOLUME INFORMATION RAID Volumes ID Name Level Strip Size Status Bootable 0 VolumeO RAIDO Stripe 128KB 149 1GB Yes Physical Disks Port Drive Model Serial Size Type Status Vol ID 0 5138081545 6Q221RYL 74 5GB 2 ST3808110AS 4LR1S469 74 5GB Press lt CTRL I gt to enter Configuration Utility D Select ESC Exit ENTER Select Menu Figure 9 Delete RAID Volume If you want to delete a RAID volume select the Delete RAID Volume option in Main Menu Press ENTER and follow on screen instructions Configuring SATA for RAID Function 75 SHB110 Socket M Full Size SBC User s Manual Intel R Matrix Storage Manager option ROM v5 7 0 1007 ICH7MR Copyright C 2003 05 Inte Corporation All Rights Reserved MAIN MENU 1 Creat RAID Volume 2 Delete RAID Volume 3 Reset Disks to Non RAID A Exit DISK VOLUME INFORMATION RAID Volumes iD Name Level Strip Size Status Bootable A Volume RAIDO Stripe 128KB 149 1GB Norma Yes Physical Disks
7. 35 SHB110 Socket M Full Size SBC User s Manual e Hard Disk Boot Priority Scroll to this item and press lt Enter gt to view the sub menu to decide the disk boot priority Phoenix AwardBlOS CMOS Setup Utility Hard Disk Boot Priori 1 Bootable Add in Cards item Help Menu Level gt Use lt gt or lt gt to select a device then press lt gt to move it up or lt gt to move it down the list Press lt ESC gt to exit this menu kg Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help FS5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Press lt Esc gt to return to the Advanced BIOS Features page e Virus Warning This option flashes on the screen During and after the system boot up any attempt to write to the boot sector or partition table of the hard disk drive will halt the system with the following message You can run an anti virus program to locate the problem The default setting is Disabled WARNING Disk boot sector is to be modified Type Y to accept write or N to abort write Award Software Inc It automatically activates while the system boots up and a warning message appears for an attempt to access the boot sector or hard disk partition table Disabled No warning message will appear for attempts to access the boot sector or hard disk partition table 36 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Man
8. 8 10 2 D defines continuous idle time before the system 0 30 40 entering the SUSPEND mode Min 1 Hr H any item defined in J is enabled and active the SUSPEND timer will be reloaded e HDD Power Down If HDD activity is not detected for a specified length of time in this field the hard disk drive will be powered down while other devices remain active e Soft Off by PWR BTTN This option only works with systems using an ATX power supply It also allows users to define which type of soft power OFF sequence the system will follow The default value is nstant Off This option follows the conventional manner of system performance when turning the power to OFF Instant Off is a software power OFF sequence requiring the power supply button is switched to OFF Upon the system s turning OFF through the power switch this option will delay the complete system power Delay 4 Sec OFF sequence approximately 4 seconds Within this delay period the system will temporarily enter into the Suspend Mode enabling you to restart the system at once Press lt Esc gt to return to the Main Menu page Phoenix Award BIOS Utility 47 SHB110 Socket M Full Size SBC User s Manual 5 10 PnP PCI Configuration Setup This section describes the configuration of PCI Personal Computer Interconnect bus system which allows I O devices to operate at speeds close to the CPU speed while communicating with other important components This s
9. Del gt immediately or press the lt Del gt and or lt Ctrl gt lt Alt gt and lt Esc gt keys simultaneously when the following message appears at the bottom of the screen during POST Power on Self Test TOENTER SETUP PRESS DEL KEY If the message disappears before you respond and you still want to enter Setup please restart the system to try it again Turning the system power OFF and ON pressing the RESET button on the system case or simultaneously pressing lt Ctrl gt lt Alt gt and lt Del gt keys can restart the system If you do not press keys at the right time and the system doesn t boot an error message will pop out to prompt you the following information PRESS lt F1 gt TO CONTINUE lt CTRL ALT ESC gt OR lt DEL gt TO ENTER SETUP Phoenix Award BIOS Utility 29 SHB110 Socket M Full Size SBC User s Manual 5 2 Control Keys Main Menu Quit and delete changes into CMOS Esc key Status Page Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu PgUp ke Increase the numeric value or make changes PgDn key Decrease the numeric value or make changes Fik General help only for Status Page Setup Menu and ey Option Page Setup Menu i Change color from total 16 colors F2 to select color Shift F2 key forward Shift F2 to select color backward F3 key Reserved F4 key F5 k Restore the previous CMOS value from CMOS only 2 key for Option Page Setup Menu F6 k
10. ETS Pi H z Jumpers and Connectors 5 SHB110 Socket M Full Size SBC User s Manual 2 2 Board Placement Ee JINY N 9 er 6 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual 2 3 Jumper Settings Proper jumer settings configure the SHB110 to meet your application purpose 2 3 1 COM2 Mode Select Jumpers JP2 JP3 JP4 These jumpers select the COM2 port s communication mode to operate RS 232 or RS 422 485 JP2 RS 232 JP4 Default L up DI up ol eraut erer eles oog SICH dils 8642 WHICH CH 5 0 O Jumpers and Connectors 7 SHB110 Socket M Full Size SBC User s Manual 2 3 2 LVDS Voltage Setting Jumper JP1 This Jumper is to select the voltage for LCD interface 2 3 3 Compact Flash Setting Jumper JP6 Optional Use this jumper to set Master Slave Compact Flash interface Master Default 8 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual 2 3 4 CMOS Clear Jum
11. RAID Function SHB110 Socket M Full Size SBC User s Manual 3 3 After entering the CREAT VOLUME MENU screen you can type the disk array name with 1 16 letters letters cannot be special characters in the item Name When finished press ENTER to select a RAID level as Figure 5 There are two RAID levels RAIDO and RAID1 Select a RAID level and press ENTER o o Intel R Matrix Storage Manager option ROM v5 7 0 1007 ICH7MR Copyright C 2003 05 Intel Corporation All Rights Reserved CREAT VOLUME MENU Name Volume RAID Level RAID Disks Select Disks Stripe Size 128KB Capacity 149 1 GB Creat Volume HELP Choose the RAID level best suited to your usage model RAIDO Data striped accross multiple physical drives for performance RAID Data mirrored across multiple physical drives for redundancy A Change TAB Next ESC Previous Menu IENTERL Select Figure 5 3 4 Set the stripe block size as Figure 6 The KB is the standard unit of stripe block size The stripe block size can be 4KB to 128KB After the setting press ENTER for the array capacity Intel R Matrix Storage Manager option ROM v5 7 0 1007 ICH7MR Copyright C 2003 05 Intel Corporation All Rights Reserved CREAT VOLUME MENU Name Volume RAID Level RAIDO Stripe Disks Select Disks Stripe Size 18KB Capacity 149 1 GB Creat Volume HELP The following are typical values RAID 128KB Change TAB Next ESC Previo
12. Save amp Exit Setup Time Date Hard Disk Type NOTE If your computer can not boot after making and saving system changes with Setup the Award BIOS will reset your system to the CMOS default settings via its built in override feature It is strongly recommended that you should avoid changing the chipset s defaults Both Award and your system manufacturer have carefully set up these defaults that provide the best performance and reliability Phoenix Award BIOS Utility 31 SHB110 Socket M Full Size SBC User s Manual 5 5 Standard CMOS Setup Menu The Standard CMOS Setup Menu displays basic information about your system Use arrow keys to highlight each item and use lt PgUp gt or lt PgDn gt key to select the value you want in each item Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Item Help Date mm dd yy Tue Feb 6 2007 Time hh mm ss 9 3 2 Menu Level Change the day month year and century IDE Channel 0 Master None IDE Channel 0 Slave None FIDE Channel 1 Master None gt IDE Channel 1 Slave None Drive A 1 44M 3 5 in Halt On A1 But Keyboard Move Enter Select PUIPD Value FI0 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults e Date The date format is lt day gt lt date gt lt month gt lt year gt Press lt F3 gt to show the calendar da It is determined by the BIOS and read only from Su
13. quit the Setup utility without saving your modifications Type N to return to the Setup utility Phoenix AwardBlOS CMOS Setup Utility gt Standard CMOS Features Load Fail Safe Defaults gt Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features set Supervisor Password Set User Password Select Item F10 Save amp Exit Setup Time Date Hard Disk Type 54 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual Chapter 6 Installation of Drivers The device drivers are located on the Product Information CD ROM that comes with the SHB110 Series package The auto run function of drivers will guide you to install the utilities and device drivers under a Windows system You can follow the onscreen instructions to install these devices m Chipset m VGA m LAN m Audio 6 1 Installing Chipset Driver 1 Run the SETUP EXE program from the driver directory in your driver CD Click Next to next step Welcome to the Setup Program This setup program will install the Intel Chipset Device Software onto this computer It is strongly recommended that you exit all Windows programs before continuing gd i Cancel Installation of Drivers 55 SHB110 Socket M Full Size SBC User s Manual 2 An Intel License Agreement appears to show you the important information Click Yes to next step Intel Chipset Device Software E EN Intel Chi
14. to continue installing the SATA driver through the floppy disk It will take about one minute to finish the driver installation Windows Setup setup will load support for the following mass storage device s Intel R 82801GHM SATA RAID Controller Mobile ICH7MDH To specify additional SCSI adapters CD ROM drives or special disk controllers for use with Wiindows including those for which you have a device support disk from a mass storage device manufacturer press S If you do not have any device support disks from a mass storage device manufacturer or do not want to specify additional mass storage devices for use with Windows press ENTER S Specify Additional Device ENTER Continue F3 Exit Figure 14 After the SATA controller driver installation is completed you can proceed to install the Windows XP Configuring SATA for RAID Function 81
15. Compact Flash Setting Jumper JP6 Cptponal 8 2 3 4 CMOS Clear Jumper JP7 ascii ciliates ued Mh ees 9 2 4 COMME CONS E 10 2 4 1 Printer Port Connector PRN cee ee 11 2 4 2 Audio Output Connector AUDIO 0 0 0 0 cece cece ee ee eee eeeeeeteeeeeeeees 12 2 4 3 CD AUX IN Connector AUX1 4 pm 12 2 4 4 ATX 4 Pin 12V In Connector CN 12 2 4 5 Serial Port Interface Connectors COM1 COM 13 2 4 6 Floppy Disk Port Connector FDD1 0ceeeeeeeeeeeeeeeeeeeeeeees 14 2 4 7 IDE Interface Connector DEI 14 2 4 8 LVDS Panel ConnectorCONe E 15 2 4 9 LCD Inverter Power Connector CN 17 2 4 10 CRT Connector CN4 EE 17 2411 SATA Gonnectors EC 18 2 4 12 Ethernet Connector LAN1 LAN2 ccccceeceeeeeeeceaeeeseeeeeeeeees 18 2 4 13 USB Port Connectors UG 19 2 4 14 USB Connector USB3 USB4 cc ccceseessseeeeeeeeeeeseseaeeassseeeeeeess 19 2 4 15 Front Panel Connector CND EEN 20 2 4 16 Mouse Keyboard Connectors MIR 21 2 4 17 System Fani Fan 2 Connectors FAN1 FAN2 eseese 21 2 4 18 CPU Fan Connector FANI sedre iana 21 Chapter 3 Hardware Installation ccseeeeessssssesseeeeeeeeeeeeees 23 3 1 Installing the POIrCeSSOM ssw nee eA ee ee 23 3 2 Installing CPUs COOGEE aeai N T NNa 24 3 3 installing tne un ele 26 Chapter 4 Hardware DeSCriptiOn c sssccsseeeeesseeeeeseeeeeseeeeeenees 27 4 1 Vulle gel lte e 27 4 2 Ge 27 4 3 SY SLOT E une EE 27 4 4 Jet ele Map EE 28 Chapter 5 Ph
16. Graphics Media Accelerator Driver This program will install the IntellA Graphics Media Accelerator Driver on this computer tis strongly recommended that you exit all Windows programs before continuing Cancel 58 Instalation of Drivers SHB110 Socket M Full Size SBC User s Manual 2 An Intel License Agreement appears to show you the important information Click Yes to next step Intel R Graphics Media Accelerator Driver DoR License Agreement Please read the following license agreement carefully Press the Page Down key to view the rest of the agreement INTEL SOFTWARE LICENSE AGREEMENT OEM IHY 2 15W Distribution amp o Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement IF vou do not wish to so agree do not install or use the Software Please Also Note IF pou are an Original Equipment Manufacturer OEM Independent fou must accept all of the terme of the license agreement in order to continue the setup program Do you accept the terms Back Intel A Installation Framework 3 The message of Readme File Information appears to show you the system requirements and installation information Please click Next Intel R Grap
17. Load the default CMOS value from BIOS default Gi table only for Option Page Setup Menu Load the Setup default only for Option Page Setup F7 key Menu F8key Reseved F9key Reseved Eigkeu Save all the CMOS changes only for Main Menu 5 3 Getting Help e Main Menu The online description of the highlighted setup function is displayed at the bottom of the screen e Status Page Setup Menu Option Page Setup Menu Press lt F1 gt to pop out a small Help window that provides the description of using appropriate keys and possible selections for highlighted items Press lt F1 gt or lt Esc gt to exit the Help Window 30 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual 5 4 The Main Menu Once you enter the Award BIOS CMOS Setup Utility the Main Menu appears on the screen In the Main Menu there are several Setup functions and a couple of Exit options for your selection Use arrow keys to select the Setup Page you intend to configure then press lt Enter gt to accept or enter its sub menu Phoenix AwardBlIOS CMOS Setup Utility Standard CMOS Features Load Fail Safe Defaults Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features set Supervisor Password Integrated Peripherals Set User Password Power Management Setup save amp Exit Setup gt PnP PCI Configurations Exit Without Saving PC Health Status A Esc Quit Select Item F10
18. OST memory testing and before the operating system booting a message Press lt Ctrl gt to enter Configuration Utility as Figure 3 shows up accordingly press lt CTRL I gt to enter the RAID BIOS setup utility Intel R Matrix Storage Manager option ROM v5 7 0 1007 ICH7MR Copyright C 2003 05 Intel Corporation All Rights Reserved RAID Volumes ID Name Level strip Size Bootable d Volumen RAID1 Mirror N A 74 5GB Yes Physical Disks Port Drive Model Serial Size Type Status Vol ID 0 ST380815AS 6Q221RYL 74 5GB 2 51380811045 4LR15469 T4 5GB Press lt CTRL I gt to enter Configuration Utility Figure 3 3 2 After you press lt CTRL I gt the Create RAID Volume screen will appear as Figure 4 If you want to create a RAID array select the Create RAID Volume option in the Main Menu and press ENTER Intel R Matrix Storage Manager option ROM v5 7 0 1007 ICH7MR Copyright C 2003 05 Intel Corporation All Rights Reserved MAIN MENU i at RAID Volun 2 Delete RAID Volume 3 Reset Disks to Non RAID 4 Exit DISK VOLUME INFORMATION RAID Volumes ID Name Level Strip Size Status Bootable Volume RAIDi Mirror N A 74 5GB Yes Physical Disks Port Drive Model Serial size Type Status Vol ID 0 ST380815AS 60221RYL 74 5GB 2 ST3808110AS 4LR1S469 74 5GB Press lt CTRL I gt to enter Configuration Utility J Select ESC Exit IENTERL Select Menu Figure 4 72 Configuring SATA for
19. Timer The integrated Watchdog Timer can be set up in the system reset mode by program Using the Watchdog Function Start 4 Un Lock WDT O 2E 87 Un lock super I O O 2E 87 Un lock super I O 4 Select Logic device O 2E 07 O 2F 08 4 Activate WDT O 2E 30 O 2F 01 Set Second or Minute O 2E F5 O 2F N N 00 or 08 See below table Set base timer O 2E F6 O 2F M 00 01 02 FF Hex Value 0 to 255 A WDT counting re set timer O 2E F6 O 2F M M 00 01 02 FF See below table Watchdog Timer 67 SHB110 Socket M Full Size SBC User s Manual IF to disable WDT O 2E 30 O 2F 00 Can be disable at any time e Timeout Value Range m to 255 Minute Second e Program Sample 2E 87 2E 87 oes Device 8 Set Minute or Second N 08 Min 00 Sec 68 Watchdog Timer SHB110 Socket M Full Size SBC User s Manual AppendixB Configuring SATA for RAID Function Configuring SATA Hard Drive s for RAID Function Controller Intel ICH7 M DH only Please follow up the steps below to configure SATA hard drive s 1 Install SATA hard drive s in your system 2 Enter the BIOS Setup to configure SATA controller mode and boot sequence 3 Configure RAID by the RAID BIOS 4 Create a floppy disk for the SATA controller driver 5 Install the SATA controller driver during the OS installation Before you begin the SATA configuration please prepare a Two SATA hard drives to ensure optimal per
20. arallel Port 378 IRQ7 Parallel Port Mode SPP Menu Level gt PWRON After PWR Fail Former Sts Move Enter Select PU PD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you want to use it If you install and in FDC or the system has no floppy drive select Disabled in this field Options Enabled and Disabled Onboard Serial Port 1 2 Select an address and corresponding interrupt for the serial port Options 3F8 IRQ4 2E8 IRQ3 3E8 IRQ4 2F8 IRQ3 Disabled Auto Onboard Paralellel Port This item allows you to determine the I O address for onboard parallel port Options 378H IRQ7 278H IRQ5 3BC IRQ7 and Disabled Parallel Port Mode Select an operating mode for the onboard parallel printer port Select Normal unless your hardware and software require another mode in this field Options EPP1 9 ECP SPP ECPEPP1 7 EPP1 7 EPP Mode Select Select EPP port type 1 7 or 1 9 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual gt ECP Mode Use DMA Select a DMA channel for the parallel port while using the ECP mode gt PWRON After PWR Fail This item enables your computer to automatically restart or return to its operating status Press lt Esc gt to return to the Integrated Peripherals page and press it agai
21. ature The current system CPU temperature will be automatically detected by the system e Current SYSTEM Temperature Show you the current system1 temperature e Current FAN1 Speed Show you the current system Ton temperature e Current FAN2 Speed Show you the current system fan2 temperature e Current FAN3 Speed Show you the current system fan3 temperature e Vcore 3 3V 5V 12V VBAT V 5VSB Show you the voltage of 3 3V 5V 12V 50 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual 5 12 Load Fail Safe Defaults When you press lt Enter gt on this item a confirmation dialog box pops out to show you such a message Phoenix AwardBlOS CMOS Setup Utility Standard CMOS Features Load Fail Safe Defaults Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password F10 Save amp Exit Setup Time Date Hard Disk Type Please press Y to load default values that will be factory settings for accomplishing the optimal performance of system operations Phoenix Award BIOS Utility 51 SHB110 Socket M Full Size SBC User s Manual 5 13 Load Optimized Defaults This option allows you to load your system configuration with default values These default settings are optimized to enable high performance features Phoenix AwardBlIOS CMOS Setup Utility gt Standard CMOS Features Load Fail Sa
22. computer later Click Finish then remove any installation media from the drives Installation of Drivers 61 SHB110 Socket M Full Size SBC User s Manual 6 3 Installing LAN Driver 1 Run the InstallShield Wizard for Ethernet from the driver directory in your driver CD Click Next to next step AEA TEK GEE B FE Feheracd DCL AEC Drier keeialfheid Brad eee PE Ctheneet PEHI HIC Wired mall motel AGEL TI GH IL Ciheras POH MC Dee onpas cii Mel Thee iraia pampim logona 2 Click Install to start the installation HEAL TER GbE amp FE Hbeornol PCI E HE Driror Inagelf hield Wirard Cisk intall ber the rt dee M ESA i rage or charge eg of peur iaa ipe kk Beck Cheek Leed Lea He pera 62 Instalation of Drivers SHB110 Socket M Full Size SBC User s Manual 3 Please wait while running the following installation operation HEAL TER GbE amp FE tiberrer PCI E HE Drier Inagelf hield Wirard The Ine eek Steed e elaine HEAL TER GHE B PE Evere PCIE MEC Dee Lkei beug Da ML DT 21 BRIEDER Seda Ca DR 4 Click Finish to complete the installation REALTEK GbE amp FE tiberrper PCI E ME Driror Installhield Wirard iratai hici Wird Compkete The neia ia ot peee mised ALALT F DE LI tarat PEH ME Cur Ok frah tice eak thee ad Installation of Drivers 63 SHB110 Socket M Full Size SBC User s Manual 6 4 64 Installing Audio Driver 1 Run the InstallShield Wizard prog
23. e damage please take care of the following jobs with precautions Do not remove boards or integrated circuits from their anti static packaging until you are ready to install them Before holding the board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds It discharges static electricity from your body m Wear a wrist grounding strap available from most electronic component stores when handling boards and components Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co Ltd Windows is a trademark of Microsoft Corporation Phoenix amp AWARD are trademarks of Phoenix Technology Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel Core 2 Duo Core Duo Core Solo are trademarks of Intel Corporation Winbond is a trademark of Winbond Electronics Corp Other brand names and trademarks are the properties and registered brands of their respective owners Table of Contents Rain E ii ESD Precautions eones eaae a eE Aa A eaS iii KepterJptrogd Heft eegener 1 1 1 SPECINCAUON E 2 1 2 Utnes Suppored eare 3 1 3 Block Diagrami eissi ai aa a aa e 4 1 4 VO iere 4 Chapter 2 Jumpers and Connectors sssssssssssussnnnnnnnnnnnnnnnnnnnnnnnnnn 5 2 1 Board DiImensiOns sserniia e aa a a a Ata aS 5 2 2 Gre ET EE 6 2 3 SEIN ee 7 2 3 1 COM2 Mode Select Jumpers JP2 JP3 JPp4 7 2 3 2 LVDS Voltage Setting Jumper JP 8 2 3 3
24. ection covers very technical items that only experienced users could change default settings Phoenix AwardBlOS CMOS Setup Utility PnP PCI Confi Jurations Init Display First PCI Slot Item Help Menu Level gt Reset Configuration Data Disabled Resources Controlled By Auto ESCD PCI VGA Palette Snoop Disabled Maximum Payload Size 128 Move Enter Select PU PD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults Fr Optimized Defaults e Init Display First This item allows you to decide whether PCI Slot or AGP to be the first primary display card e Reset Configuration Data Normally you leave this item Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup or if installing a new add on cause the system reconfiguration a serious conflict that the operating system can not boot Options Enabled Disabled e Resources Controlled By The Award Plug and Play BIOS can automatically configure all boot and Plug and Play compatible devices If you select Auto all interrupt request IRQ DMA assignment and Used DMA fields disappear as the BIOS automatically assigns them The default value is Manual 48 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual e IRQ Resources When resources are controlled manually assign each system interrupt to one of the following types in accordance with the type
25. ector to support the audio interface e 4 6 8 10 C in 6 len Ca ao o E e de Out 10 GND el ele oa ID D o ID 2 4 3 CD AUXIN Connector AUX1 4 pin 110 a lega lela 2 0 IN Left 3 0 EC An 2 4 4 ATX 4 Pin 12V In Connector CN1 You can connect it to the ATX12V power supply for CPU Core Voltage 12 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual 2 4 5 Serial Port Interface Connectors COM1 COM2 The serial interface for the board consists of COM1 port COM1 and COM2 COM2 supports RS 232 RS422 RS485 RS232 Pin Assignment Pin Signal Pin TT Data Carrier Detect Data Set Ready DSR 1 DCD 2 a ol 2 1 Receive Data RXD Request to Send RTS 3 0 O 4 5 Transmit Data TXD 6 Clear to Send CTS 5 jo o 6 Data Terminal Ready Ring Indicator RI 7 j0 O78 DTR 9 0 Of10 COM limo 2 310 OF 4 510 o 6 7 0 oF 8 91 0 O710 COM lipo 2 3 0 O14 5 io o 6 710 DIS 9 0 oO710 re ereuna eno oe Jumpers and Connectors 13 SHB110 Socket M Full Size SBC User s Manual 2 4 6 Floppy Disk Port Connector FDD1 The board provides a 34 pin header type connector FDD1 supporting up to two floppy drives The floppy drives may be any one of the following types 5 25 360KB 1 2MB and 3 5 720KB 1 44MB 2 88MB Pin asi Pin Signal Pin Signal NWO 4 iwc JL Jeno NC zleo index ND Motor enable A 11 Drive select B Drive select A 16 Motor
26. enableB 17 GND 22 Write data Write gate GND 29 34 Diskchanget d FDD1 O O O 034 O O O 033 2 4 7 IDE interface Connector IDE1 The board provided one IDE Port to support maximum up to two IDE devices ee ee ee 14 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual rin Bescripion Pin Descapton Pin pesonpnon IOW 24 GND 22 IGND C HDC CSO HDC CSI 4 IDE1 z 28 N C I 34 N C i 0 T 000040 000039 _ 2 4 8 LVDS Panel Connector CN3 CN3 is a JST 40 pin connector for the LVDS flat panel connection LVDSB_D3 12 LVDSB_Do LVDSB_D3 14 LVDSB_DO GND LVDSB_CLK LVDSB_D1 Jumpers and Connectors 15 SHB110 Socket M Full Size SBC User s Manual Pin Signal Pin Signal 24 GND GND 30 GND CN3 2 fel ae cts Le C C CJ CJ C C C C C Cc Cc CJ C C C C C C C C Cc Cc C C C C C C C C Cc ech 40 UC 39 16 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual 2 4 9 LCD Inverter Power Connector CN2 CN2 UUUDDUI 2 4 10 CRT Connector CNA CN14 is D SUB 15 Pin connector commonly used for the CRT Monitor 2 Green La ra va 5 enn Le z aaxo Lalaen NA CN4 Jumpers and Connectors 17 SHB110 Socket M Full Size SBC User s Manual 2 4 11 SATA Connectors SATA1 2 These SATA connectors are for high speed SATA interface p
27. fe Defaults Advanced BIOS Features Load Optimized Defaults gt Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password A Esc Quit Select Item F10 Save amp Exit Setup Time Date Hard Disk Type To load CMOS SRAM with SETUP default values please enter Y If not please enter N 5 14 Set Supervisor User Password You can set a supervisor or user password or both of them The differences between them are 1 Supervisor password You can enter and change the options on the setup menu 2 User password You can just enter but have no right to change the options on the setup menu When you select this function the following message will appear at the center of the screen to assist you in creating a password ENTER PASSWORD Type a maximum eight character password and press lt Enter gt This typed password will clear previously entered password from the CMOS memory You will be asked to confirm this password Type this password again and press lt Enter gt You may also press lt Esc gt to 52 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual abort this selection and not enter a password To disable the password just press lt Enter gt when you are prompted to enter a password A message will confirm the password is getting disabled Once the password is disabled the system will boot and you can enter Setup free
28. formance it is recommended that you use two hard drives with identical model and capacity b An empty formatted floppy disk c Windows XP setup disk 1 Installing SATA hard drive s in your system Connect one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port s on the board Then connect the power connector of power supply to the hard drive 2 Configuring SATA controller mode and boot sequence by the BIOS Setup You have to make sure whether the SATA controller is configured correctly by system BIOS Setup and set up BIOS boot sequence for the SATA hard drive s Configuring SATA for RAID Function 69 SHB110 Socket M Full Size SBC User s Manual 2 1 Turn on your system and press the Del button to enter BIOS Setup during running POST Power On Self Test If you want to create RAID just select RAID for SATA Mode default IDE under the Integrated Peripherals menu Phoenix AwardBlOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode IDE DMA transfer access On Chip Primary PCI IDE IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UMDA IDE Primary Slave UMDA On Chip Secondary PCI IDE IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UMDA IDE Secondary Salve UMDA SATA Mode SATA PORT Speed Settings Item Help Menu Level gt gt Enabled Enabled Enabled Auto Auto Auto Auto Enabled Au
29. he board eS e AE i Step 2 Connect the housing to the Power Socket Removing the CPU 1 Before removing the CPU turn off the system power waiting for about 3 minutes until the heat radiation plate of the cooling fan and the CPU cooled down DI Note Hot CPU and heat radiation plate might cause burns 2 To remove the CPU lift the releasing lever of the socket 3 To remove the CPU reverse the installation steps Hardware Installation 25 SHB110 Socket M Full Size SBC User s Manual 3 3 Installing the Memory The board supports two 240 pin DDR2 DIMM memory sockets with maximum memory capacity up to 4GB Please follow steps below to install the memory modules 1 Push down latches on each side of the DIMM socket 2 Align the memory module with the socket that notches of memory module must match the socket keys for a correct intallation 3 Install the memory module into the socket and push it firmly down until it is fully seated The socket latches are levered upwards and clipped on to the edges of the DIMM 4 Install any remaining DIMM modules Memory Socket 26 Hardware Installation SHB110 Socket M Full Size SBC User s Manual Chapter 4 Hardware Description 4 1 Microprocessors i TM TM TM The SHB110 Series supports Intel Core 2 Duo Core Duo Core Solo processors which make your system operated under Windows 2000 XP and Linux environments The system performance depends on the microp
30. hics Media Accelerator Driver Readme File Information Refer to the Readme file below to view the system requirements and installation information Press the Page Down key to view the rest of the file Ec arc cee eee DEE Production wersion Releases Microsoft Windows 2000 Microsoft windows FP Driver Revision Production version 14 29 Package 35162 Graphics 6 14 10 4820 HOM Audio 5 10 0 1026 Intel A Installation Framework Installation of Drivers 59 SHB110 Socket M Full Size SBC User s Manual 4 Please wait while running the following setup operations Intel R Graphics Media Accelerator Driver setup Progress Please wait while the following components are installed Copying file ig pun exe Copying file dtvap dl Copying file Ich B bmp Copying file Ich BA bp Copying file HDMIENU dll Creating key HELM System CurrentControlS et ControhindowsSystemD irecte Creating key HELMS System CurrentControlS et ervices Valm D evicel SystemL Creating key HELMS System CurrentControlS et Services ValmD evicel SystemL Creating key HELMASOFT WARE SMicrosofth indows Curent ersion Uningtall Creating key HELMASOFT WARE SMicrosotth indows Curent ersion Uninstall Installing Driver Intel A 0965 0963 Express Chipset Famil Version 6 14 10 4020 gt Hent IntellA Installation Framework 5 When this message appears please click Next Intel R Graphics Media Accelerator Dri
31. lect Type 1 If the HDD interface controller supports SCSI select None If the HDD interface controller supports CD ROM select None CYLS number of cylinders LANDZONE HEADS numberof heads _ SECTORS PRECOMP write precom Jong HDD access mode lf there is no hard disk drive installed select NONE and press lt Enter gt Dive A type Drive B type The item identifies the types of floppy disk installed in the computer as drive A or drive B None No floppy drive installed 360K 3 5in 3 5 inch PC type standard drive 360Kb Mini ITXcit 3 5 inch AT type high density drive 1 2MB Mini IT Xcity 1 44M 3 5 in_ 3 5 inch double sided drive 1 44MB Mini ITXcity Phoenix Award BIOS Utility 33 SHB110 Socket M Full Size SBC User s Manual e Halt On This ttem determines whether the system will halt or not if an error is detected while powering up The system booting will halt on any errors detected default Whenever BIOS detects a non fatal error the system will stop and you will be prompted The system booting will not stop for a keyboard All But ieee Keyboard error it will stop for other errors The system booting will not stop for a disk error it dech ill stop for oth Diskette will stop for other errors The system booting will not stop for a keyboard or Geh disk it will stop for oth Disk Key isk error it will stop for other errors Press lt Esc gt to return to the Mai
32. ly PASSWORD DISABLED When a password is enabled you have to type it every time you enter the Setup It prevents any unauthorized persons from changing your system configuration Additionally when a password is enabled you can also require the BIOS to request a password every time the system reboots This would prevent unauthorized use of your computer You decide when the password is required for the BIOS Features Setup Menu and its Security option If the Security option is set to System the password is required during booting up and entry into the Setup if it is set as Setup a prompt will only appear before entering the Setup 5 15 Save amp Exit Setup This section allows you to determine whether or not to accept your modifications Type Y to quit the setup utility and save all changes into the CMOS memory Type N to bring you back to the Setup utility Phoenix AwardBlOS CMOS Setup Utility Standard CMOS Features Load Fail Safe Defaults Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Esc Quit F10 Save amp Exit Setup Time Date Hard Disk Type Phoenix Award BIOS Utility 53 SHB110 Socket M Full Size SBC User s Manual 5 16 Exit Without Saving Select this option to exit the Setup utility without saving changes you have made in this session Type Y and it will
33. menu gt IDE Primary Secondary Master Slave PIO The four IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes 0 to 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device gt IDE Primary Secondary Master Slave UDMA Select the mode of operation for the IDE drive Ultra DMA 33 66 100 133 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver If your hard drive and system software both support Ultra DMA 33 66 100 133 select Auto to enable UDMA mode by BIOS On Chip Serial ATA Setting SATA Mode There are these options for you to set up SATA mode IDE RAID or AHCI On Chip Serial ATA Use this item to enable or disable the built in on chip serial ATA SATA PORT Speed Settings Use this item to select SATA or SATA II device support forcedly PATA IDE Mode Use this item to set the PATA IDE mode When set to Primary P1 and P3 are Secondary on the other hand when set to Secondary PO and P2 are Primary SATA Port If the PATA IDE Mode is Primary it will show P1 P3 is Secondary which means SATA 2 and SATA 4 are Secondary If the PATA IDE Mode is Secondary it will show PO P2 is Primary which means SATA 1 and SATA 8 are Primary Press lt Esc gt to return to the In
34. mory over 64MB in OS 2 Press lt Esc gt to return to the Main Menu page 38 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual 5 7 Advanced Chipset Features This section contains completely optimized chipse s features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your system hardware Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features PCI Express Port 1 PCI Express Port 2 PCI Express Port 3 PCI Express Port 4 PCI Express Port 5 PCI Express Port 6 PCI E Compliancy Mode PEG Onchip VGA Control On Chip Frame Buffer Size DVMT Mode DVMT FIXED Memory Size Boot Display Panel Scaling Panel Number Enabled Enabled Enabled Enabled Enabled Enabled v1 0a Auto 8MB DVMT 128MB CRT Auto 640 X 480 item Help Menu Level rz Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults e PCI Express Port 1 6 There are several PCI Express Ports for your selection e PCI E Compliancy Mode This item allows you to set the version of the PCI Express base specifications VGA Setting e PEG Onchip VGA Control Use this item to choose the primary display card e On Chip Frame Buffer Size Use this item to set the VGA frame buffe
35. n Before installing the processor please access Intel website for more detailed information http Avww intel com 3 1 Installing the Porcessor Before installing the CPU please make sure that your CPU belongs to Intel Core2 Duo Core Duo Core Solo Mobile Processor Core Core Duo anette Solo Jnsteie al a ae see EECH Peers FREE WAAT EIER Soe eee eee ees HELLER ECTS SIS R TnzannERstRRIRREERREEKKKN e e e KE KA me e s gaea a CR e e me KE l i Carefully follow up these steps below to install the CPU Step 1 Before installing your CPU please check and confirm all jumpers are correctly set Step 2 Lift the releasing lever of the socket Hardware Installation 23 SHB110 Socket M Full Size SBC User s Manual Step 3 Align pins of the CPU with pin holes of the socket Be careful of the CPU s orientation t rer P ee Nice See E E Socket fy Step 5 Push down the releasing lever and lock it onto the key hook Step 6 Hook the hole in ZIF clip for the CPU cooling fan orientation onto the notch on the socket 3 2 Installing CPU Cooler DY 4 Note1 To install the CPU cooler first time please follow the procedure step by step AJ Note2 For the second or later installation please start the procedure from the step 2 24 Hardware Installation SHB110 Socket M Full Size SBC User s Manual Step 1 Install the Back Plate at the backside of t
36. n Menu page 34 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual 5 6 Advanced BIOS Features This section allows you to configure and improve your system to set up some system features according to your preference Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features CPU Feature Hard Disk Boot Priority Virus Warning CPU L1 amp L2 Cache Quick Power On Shelf Test First Boot Device second Boot Device Third Boot Device Boot Other Device Boot Up NumLock Status Security Option APIC Mode MPS Version Control For OS OS Select For DRAM gt 64MB Press Enter Item Help Press Enter Disabled Enabled Enabled Floppy Hard Disk CDROM Enabled On Setup Enabled 1 4 Non OS2 Menu Level gt rz Move Enter Select PUIPD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults e CPU Feature Scroll to this item and press lt Enter gt to view the CPU Feature sub menu Phoenix AwardBlOS CMOS Setup Utility CPU Features Delay Prior to Thermal Thermal Management C1E Function Execute Disable Bit Virtual ization Technology 16 Min Item Help Thermal Monitor 2 Auto Enabled Enabled Menu Level gt rz Move Enter Select PU PD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Phoenix Award BIOS Utility
37. n to the Main Menu page 5 9 Power Management Setup The Power Management Setup allows you to save energy of your system effectively It will shut down the hard disk and turn OFF video display after a period of inactivity Phoenix AwardBlOS CMOS Setup Utility Power Manaa ement Setup item Help ACPI Function Menu Level Enabled ACPI Suspend Type Power Management Video Off Method Video Off In Suspend Suspend Type Suspend Mode HDD Power Down Soft Off by PWR BTTN alle User Define DPMS Yes Stop Grant Disabled Disabled Instant Off Move Enter Select PU PD Value Fi0 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults Fr Optimized Defaults e ACPI Function This item allows you to enable disable the Advanced Configuration and Power Management ACPI The function is always Enablea e ACPI Suspend Type This item specifies the power saving modes for ACPI function If your operating system supports ACPI such as Windows 98SE Phoenix Award BIOS Utility 45 SHB110 Socket M Full Size SBC User s Manual Windows ME and Windows 2000 you can choose to enter the Standby mode in S1 POS or S3 STR fashion through the setting of this field Options are S1 POS The S1 sleep mode is a low power state In this state no system context is lost CPU or chipset and hardware maintains all system contexts S3 STR The S3 sleep mode is a lower p
38. nday y to Saturday date It can be keyed with the numerical function key from 1 to 31 month It is from January to December It shows the current year of BIOS e Time This item shows current time of your system with the format lt hour gt lt minute gt lt second gt The time is calculated based on the 24 hour military time clock For example 1 p m is 13 00 00 32 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave These items identify the types of each IDE channel installed in the computer There are 45 predefined types Type 1 to Type 45 and 2 user s definable types Type User for Enhanced IDE BIOS Press lt PgUp gt lt gt or lt PgDn gt lt gt to select a numbered hard disk type or directly type the number and press lt Enter gt Please be noted your drive s specifications must match the drive table The hard disk will not work properly if you enter improper information If your hard disk drive type does not match or is not listed you can use Type User to manually define your own drive type If selecting Type User you will be asked to enter related information in the following items Directly key in the information and press lt Enter gt This information should be provided in the documentation from your hard disk vendor or the system manufacturer If the HDD interface controller supports ESDI se
39. oenix Award BIOS Utility cccesssssssseeeeeseeeeeeees 29 5 1 Entenono SCUD EE 29 5 2 CONTOLKEVS resoan T A a a 30 5 3 Gening He EE 30 5 4 THe MaN Mei esasa Ee 31 5 5 Standard CMOS Setup Men 32 5 6 Advanced BIOS Features EEN 35 5 7 Advanced Chipset Features AANEREN 39 5 8 Integrated Peripherals awk ei esha Ges 40 5 9 Power Management Geiup 45 5 10 PnP PCI Configuration Getup 48 5 11 PCARICAIIA Slats EE 50 5 12 Load Fail Safe Defaults vssseisssecsesadssccasacigisaindcacaatiaraevariuatsvaneianseceaninevd 51 5 13 Load Optimized Defaults EE 52 5 14 Set Supervisor User Password 52 5 15 Save amp Exit SCUD EE 53 5 16 Exit Without Saving ennie onera e EE 54 Chapter 6 Installation of Drivers ccecessssssessseeeeeeseeeeeeeees 55 6 1 Installing Chipset Driver ccccccceccceeceeeeeeeeeeeeeeeeeseeeaeaaeneeeeeeeeeeeeeees 55 6 2 Installitag VGA DIV TEE 58 6 3 Installing LAN Diver Eeer 62 6 4 lnstalling Audio Driver EEN 64 Appendix A Watchdog Timer cccccccssssseeeseeeesseeeseeeenseeeseeees 67 Appendix B Configuring SATA for RAID Function 69 MEMO yi SHB110 Socket M Full Size SBC User s Manual Chapter 1 Introduction The SHB110 PICMG 1 3 full size Single Board Computer supports Intel Core 2Duo Core Duo Core Solo processors with FSB 533 667 MHz The board integrates chipsets Intel 945GME and ICH7M DH that deliver outstanding system performance thro
40. orts and they can be connected to hard disk devices Sol Signal sta d K DOOU OOD e sarana JI 2 4 12 Ethernet Connector LAN1 LAN2 The RJ 45 connectors LAN1 and LAN2 are for Ethernet To connect the board to 100 Base T or 1000 Base T hub just plug one end of the cable into LAN1 and connect the other end phone jack to a 100 Base T hub or 1000 Base T hub Pt te ata a MDs Te tata La we Ts Rea 3 MDs langen 4 we lagen s we Te Re Data Lal wc Te Rufo s we alima B Du 18 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual 2 4 13 USB Port Connectors USB1 2 The Universal Serial Bus USB port connector on the board is for the installation of peripherals supporting the USB interface Each USB port consists of two 4 pin standard USB ports USB1 USB2 2 4 14 USB Connector USB3 USB4 The Universal Serial Bus USB connector on this board is for installing versatile USB interface peripherals This is a 10 pin standard USB connector 1 USB 2 USB POWER POWER 5 USB Po 6 USBP1 7 USBGND 8 USBGND 2M to end Jumpers and Connectors 19 SHB110 Socket M Full Size SBC User s Manual 2 4 15 Front Panel Connector CN5 HDDLED HWRST PWRSW EXT SPK NC Buzzer EXT SPK 14 12 10 8 6 4 2 13 11 9 7 5 3 1 HDDLED HW RST PWRSW Nc PWRLED NC PWRLED Power LED Pins 1 3 5 connect the system power LED indicator to its respective
41. ower state where the information of system configuration and open applications files is saved to main memory that remains powered while most other hardware components turn off to save energy The information stored in memory will be used to restore the system when a wake up event occurs e Power Management This option allows you to select the type of power Management Options APM ACPI e Video Off Method This setting determines the manner in which the monitor is blanked V H It turns OFF vertical and horizontal synchronization ports SYNC Blank and writes blanks to the video buffer Select this option if your monitor supports the Display Power Management Signaling DPMS standard of the Video Electronics Standards Association VESA Use the supplied software for your video subsystem to select video power management values Blank Screen The System only writes blanks to the video buffer e Video Off In Suspend This ttem defines if the video is powered down when the system is put into suspend mode e Suspend Type If this item is set to the default Stop Grant the CPU will go into Idle Mode during power saving mode e Suspend Mode After a selected period of system inactivity 1 minute to 1 hour all devices except the CPU shut off The default value is Disabled 46 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual Disabled The System will never enter the SUSPEND mode 1 2 4 6
42. per JP7 You may need to use this jumper is to clear the CMOS memory if incorrect BIOS settings CMOS Clear Normal Default Jumpers and Connectors 9 SHB110 Socket M Full Size SBC User s Manual 2 4 Connectors Connectors connect this board with other parts of the system Loose or improper connection might cause problems Make sure all connectors are properly and firmly connected Here is a Summary table shows you all connectors on the board See Lesen Function connector SE 4P 12V IN EE RJ 45 LANI Option LCD Inverter Power LCD Inverter Power Power ONS Laus RJ 45 LAN2 o mm es w CRT Comectr ona ep mm eso o ooo 10 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual 2 4 1 Printer Port Connector PRN1 Print Port Connector Default This board has a multi mode parallel port to support 1 Standard Mode IBM PC XT PC AT and PS 2 are compatible with bi directional parallel port 2 Enhanced Mode Enhance parallel port EPP is compatible with EPP 1 7 and EPP 1 9 IEEE 1284 compliant 3 High Speed Mode Microsoft and Hewlett Packard extended capabilities port ECP is IEEE 1284 compliant pin ged Pn Sei Cs paas Lk Cr paas Jefas Co paar roficroweaes oo0o0co00odcono0nnndononn00 O amp OU DD DDDDDD DUDU DU Jumpers and Connectors 11 SHB110 Socket M Full Size SBC User s Manual 2 4 2 Audio Output Connector AUDIO1 AUDIO is a 10 pin conn
43. pport disks from a mass storage device manufacturer or do not want to specify additional mass storage devices for use with Windows press ENTER S Specify Additional Device ENTER Continue F3 Exit Figure 12 Configuring SATA for RAID Function 79 SHB110 Socket M Full Size SBC User s Manual 5 3 If the Setup correctly recognizes the driver of the floppy disk a controller menu as Figure 13 will appear below Use the ARROW keys to select Intel R 82801 GHM SATA RAID Controller Mobile ICH7MDH and press ENTER Then it will begin to load the SATA driver from the floppy disk Windows Setup You have chosen to configure a SCSI Adapter for use with Windows using a device support disk provided by an adapter manufacturer Select the SCSI Adapter you want from the following list or press ESC to return to the previous screen Intel R 631xESB 632xESB SATA RAID Controller Server Workstation ESB2 Intel R 631xESB 632xESB SATA AHCI Controller Server Workstation ESB2 Intel R 82801GHM SATA RAID Controller Mobile ICH7MDH Intel R 82801GR GH SATA RAID Controller Desktop ICH7R DH ENTER Continue F3 Exit Figure 13 Note f a message on the screen saying that one or some file s cannot be found please check the floppy disk or copy the correct SATA driver again from the driver CD 80 Configuring SATA for RAID Function 5 4 SHB110 Socket M Full Size SBC User s Manual When the screen appears as below press ENTER
44. pset Device Software ee inte License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHW j IM Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the ZGoftware until you have carefully read the Following terms and conditions By loading or using the Software You agree to the terms of this Agreement IF you do not wish to so agree do nok install or use the Software Please Also Note TF you are an Original Equipment Manufacturer OEM Independent Hardware vendor THY or Independent Software Vendor ON this complete LICENSE AGREEMENT applies 3 Intel Chipset Device Software Intel Chipset Device Software Setup Progress Please wait while the Following setup operations are performed Installing Driver Intel R 9635 0965 PCI Express Root Port 2991 Version 6 3 0 1011 Installing Driver Intel R ICHBDO LPC InterFace Controller 2614 Version amp 3 0 1013 Installing Driver Intel F ICHS Family PCI Express Root Port 1 283F Version amp 3 0 1013 Installing Driver Intel R ICHS Family PCI Express Root Port 4 2845 Wersion 3 3 0 1013 Installing Driver Intel R ICHS Family PCI Express Rook Port 5 2847 Version 630 1013 56 Instalation of Drivers
45. r USB ports compliant with USB Spec Rev 2 0 e VGA Controller H Intel Graphic Media Accelerator 950 integrated on Intel D Introduction SHB110 Socket M Full Size SBC User s Manual 945GME Ethernet m The LAN1 LANZ2 is 82573L Ethernet controller support 10 100 1000 Mb Dual PCI Express LAN Serial ATA Support Serial ATA Serial ATA II Two Serial ATA channels for a total of two Serial ATA hard drives Maximum transfer rate could up to 3Gb s Audio m Realtek ALC203 Audio Codec onboard Hardware Monitoring m Detection of CPU temperature System temperature Power failure and Fan speed Watchdog Timer Reset Support 1 255 level Dimensions 338x 126mm 8 layer wy NOTE All specifications and images are subject to change without notice 1 2 Utilities Supported Intel 945GME Utility and Drivers VGA Drivers Ethernet Utility and Drivers Audio Utility and Drivers Introduction 3 SHB110 Socket M Full Size SBC User s Manual 1 3 Block Diagram Intel Core Duo ore Que fCore Solo Mobile Processor 329667 Mhz Mobile Processor DORI 333 667 PCI Ext for LON mii PCI Ex for LAN ICH M OH udio CodeciACaT 4 P I Slot Bultin on Backplane Super K O Notice 4 USB 2 0 Port built in on Backplane 1 4 UO Bracket 4 Introduction SHB110 Socket M Full Size SBC User s Manual Chapter 2 Jumpers and Connectors 2 1 Board Dimensions GG a v d aas b i Een
46. r size Phoenix Award BIOS Utility 39 SHB110 Socket M Full Size SBC User s Manual DVMT Mode DVMT Dynamic Video Memory Technology helps you select the video mode DVMT Fixed Memory Size DVMT Dynamic Video Memory Technology allows you to select a maximum size of dynamic amount usage of the video memory The system would configure the video memory dependent on your application Boot Display This item is for Intel define ADD card only Press lt Esc gt to return to the Main Menu page 5 8 Integrated Peripherals This section allows you to configure your SuperlO Device IDE Function and Onboard Device Phoenix AwardBIOS CMOS Setup Utility _Integrated Peripherals OnChip IDE Device Press Enter Rom neip Onboard Device Press Enter Super IO Device Press Enter Menu Level gt Move Enter Select PUIPD Value Fid Save ESC Exit Fi General Help FS Previous Values F6 Fail Safe Defaults Fr Optimized Defaults 40 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual e OnChip IDE Device Scroll to this item and press lt Enter gt to view the sub menu OnChip IDE Device Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode Enabled mem Herp IDE DMA transfer access Enabled Menu Level gt On Chip Primary PCI IDE Enabled IDE Primary Master PIO Auto IDE Primary Slave PIO Auto IDE Primary Master UMDA Auto IDE Primary Slave UMDA Auto
47. ram from the driver directory in your driver CD Please wait while running the following operation et Realtek HD Audio InstallShield Wizard Extracting Files The contents of this package are being extracted Please wait while the Installshield Wizard extracts the Files needed to install Realtek HD Audio on your computer This may take a few moments Reading contents of package aaa lt Back Net Cancel 2 When this message appears please click Next Balok High hni an kr katzctegr Setup ft 1 HT SN Realtek High Definition Audio Driver RI op Bria jji feline baii Bri heja UL RT ert gea t Phe Ire eed eed ja Nip gs i iy Leds Fee el de ee ie ee ee ag Instalation of Drivers SHB110 Socket M Full Size SBC User s Manual 3 You will be asked to reboot your computer when the InstallShield Wizard is installed Please click Yes want to restart my computer now or No will restart my computer later and next click Finish to complete the installation aet ihigh lalmi pap Aeda Realtek Hig h Definition Audio Driver RI op e ee eee fie OO DI AA ee ee ee Installation of Drivers 65 SHB110 Socket M Full Size SBC User s Manual MEMO 66 Instalation of Drivers SHB110 Socket M Full Size SBC User s Manual AppendixA Watchdog Timer Watchdog Timer Setting After the system stops working for a while it can be auto reset by the Watchdog
48. rch for the type of floppy disk drive by Disabled track number There will be no warning message displayed if the installed drive is 360K Phoenix Award BIOS Utility 37 SHB110 Socket M Full Size SBC User s Manual System lf a wrong password is entered at the prompt the system will not boot the access to Setup will be denied either lf a wrong password is entered at the prompt the system will boot but the access to Setup will be denied W Boot Up NumLock Status Set the the Num Lock status when the system is powered on The default value is On Security Option This item allows you to limit access to the system and Setup or just to Setup The default value is Setup A NOTE To disable the security select PASSWORD SETTING at Main Menu and then you will be asked to enter a password Do not type anything just press lt Enter gt and it will disable the security Once the security is disabled the system will boot and you can enter Setup freely APIC Mode Use this item to enable or disable APIC Advanced Programmable Interrupt Controller mode that provides symmetric multi processing SMP for systems MPS Version Control For OS This item specifies the version of the Multiprocessor Specification MPS Version 1 4 has extended configuration tables to improve support for multiple PCI bus configurations and provide future expandability OS Select for DRAM gt 64MB This item allows you to access the me
49. rocessor Make sure all correct settings are arranged for your installed microprocessor to prevent the CPU from damages 4 2 BIOS The SHB110 Series uses Award Plug and Play BIOS with a single 4Mbit Flash EPROM 4 3 System Memory The SHB110 Series supports two 240 pin DDR2 DIMM sockets for a maximum memory of 4GB DDR2 SDRAMs The memory module can come in sizes of 64MB 128MB 256MB 512MB 1GB and 2GB Hardware Description 27 SHB110 Socket M Full Size SBC User s Manual 4 4 O Port Address Map TM TM TM The Intel Core 2 Duo Core Duo Core Solo CPUs can communicate via I O ports There are total 1KB port addresses available for assignment to other devices via I O expansion cards Address Devices DMA controller 2 OF 1 Reset math coprocessor OF8 OFF Math processor Disable watchdog timer operation read 121 Enable watchdog timer operation read Prototype card 360 36F Reserved 3F8 3FF Serial port 1 COM1 2F8 2FF Serial port 2 COM2 28 Hardware Description SHB110 Socket M Full Size SBC User s Manual Chapter 5 Phoenix Award BIOS Utility The Phoenix Award BIOS provides users with a built in Setup program to modify basic system configuration All configured parameters are stored in a battery backed up RAM CMOS RAM to save the Setup information whenever the power is turned off 5 1 Entering Setup There are two ways to enter the Setup program You may either turn ON the computer and press lt
50. switch on the case Pin 1 is and pin 5 assigned to Pin 3 is defined as NC External Speaker and Internal Buzzer Connector Short Pin 4 6 for Internal Buzzer Hardware Reset Pins 11 and 12 are designed for Hardware Reset m HDD Activity LED This connector extends to the hard drive activity LED on the control panel This LED will flash when the HDD is being accessed Pins 13 and 14 can be connected to the hard disk drive and front panel HDD LED Power Botton Pins 9 and 10 connect the front panel s ATX power button to the card which allows users to control ATX power supply on or off 20 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual 2 4 16 Mouse Keyboard Connectors MS1 KB1 The board provides a keyboard KB1 and Mouse M 1 interface with two 5 pin connectors Clock 1 Data 200 No Connecton 3 O GNDI 40 Power 50 2 4 17 System Fan1 Fan 2 Connectors FAN1 FAN2 You can connect the system cooling fan cable to FAN1 FAN2 for system cooling fan power Pin Signal cant FAN2 TA Jo at oe SENSOR 2 4 18 CPU Fan Connector FAN3 A CPU fan is always needed for cooling CPU heat The CPU fan connector FANS provides power to the CPU fan Pin Signal ran CS F at oe SENSOR Jumpers and Connectors 21 SHB110 Socket M Full Size SBC User s Manual MEMO 22 Jumpers and Connectors SHB110 Socket M Full Size SBC User s Manual Chapter 3 Hardware Installatio
51. tegrated Peripherals page 42 Phoenix Award BIOS Utility SHB110 Socket M Full Size SBC User s Manual e Onboard Device Scroll to this item and press lt Enter gt to view the sub menu Onboard Device Phoenix AwardBlOS CMOS Setup Utility Onboard Device USB Controller Enabled USB 2 0 Controller Enabled USB Keyboard Support Enabled ACST Audio Auto Item Help Menu Level gt Move Enter Select PU PD Value Fi0 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults Fr Optimized Defaults gt USB Controller Enable this item if you are using the USB in the system You should disable this item if a higher level controller is added gt USB 2 0 Controller Enable this item if you are using the EHCI USB2 0 controller in the system gt USB Keyboard Support Enable this item if the system has a Universal Serial Bus USB controller and you have a USB keyboard gt AC 97 Audio Use this item to enable or disable the onboard AC 97 Audio function Press lt Esc gt to return to the Integrated Peripherals page Phoenix Award BIOS Utility 43 SHB110 Socket M Full Size SBC User s Manual e Super IO Device Scroll to this item and press lt Enter gt to view the sub menu Super lO Device 44 Phoenix AwardBIOS CMOS Setup Utility super IO Device item Help Onboard FDC Controller Enabled Onboard Serial Port 1 SFB IRQ4 Onboard Serial Port 2 2F8ARQ3 Onboard P
52. to Auto Auto Auto RAID Disabled Move Enter Select PU PD Value Fi0 Save ESC Exit F1 General Help F5 Previous Values Ff Optimized Defaults Figure 1 70 Configuring SATA for RAID Function SHB110 Socket M Full Size SBC User s Manual 2 2 Set CDROM for First Boot Device under the Advanced BIOS Features menu to boot CD ROM after system restarts Figure 2 Phoenix AwardBlOS CMOS Setup Utility Advanced BIOS Features gt CPU Feature Hard Disk Boot Priority CPU L1 amp L2 Cache Quick Power On Shelf Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Onboard Lan Boot ROM Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Security Option APIC Mode MPS Version Control For OS item Help Menu Level gt Press Enter Press Enter Enabled Enabled CDROM Hard Disk LS120 Enabled Disabled Disabled Disabled On Fast Disabled Select Your Boot Device Priority Setup Enabled 1 4 Move Enter Select PU PD Value F10 S5ave ESC Exit F1 General Help F5 Previous Values 2 3 F7 Optimized Defaults Figure 2 Save and exit the BIOS Setup 3 Configuring RAID by the RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array Configuring SATA for RAID Function 71 SHB110 Socket M Full Size SBC User s Manual 3 1 After the P
53. ual NOTE This function is only available with DOS and other operating systems that do not trap INT13 CPU L1 amp L2 Cache These two options speed up memory access However it depends on the CPU chipset design The default setting is Enabled CPUs without built in internal cache will not provide the CPU Internal Cache item on the menu Enabled Enable cache Disabled Disable cache Quick Power On Self Test This option speeds up Power on Self Test POST after you turn on the system power If set as Enabled BIOS will shorten or skip some check items during POST The default setting is Enabled First Second Third Boot Device These items let you select the 17 2 and 3 devices that the system will search for during its boot up sequence The wide range of selection includes Floppy LS120 ZIP 100 HDDO 3 SCSI and CDROM Boot Other Device This item allows users to enable or disable the boot device not listed in the First Second Third boot devices option above The default setting is Enabled Boot Up Floppy Seek During POST BIOS will determine the floppy disk drive type 40 or 80 tracks The 360Kb type is 40 tracks while 720Kb 1 2MB and 1 44MB are all 80 tracks The default value is Enablea BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks Please be noted BIOS can not differentiate 720K 1 2M or 1 44M drive type as they all are 80 tracks Enabled BIOS will not sea
54. ugh high bandwidth interfaces multiple I O functions for interactive applications and various embedded computing solutions There are two DDR2 DIMM sockets for dual channel DDR2 533 667 maximum memory capacity up to 4GB The board also features Ethernet 10 100 1000Mb dual PCI Express LAN and two serial ATA channels for a tatal of two serial ATA hard drives at maximum transfer rate up to 3Gb s Four USB 2 0 Port and built in high definition audio codec can achieve the best stability and reliability for industrial applications Introduction 1 SHB110 Socket M Full Size SBC User s Manual 1 1 Specifications TM TM TM e CPU Intel Core 2 Duo Core Duo Core Solo processors e System Chipset Intel 945GME and ICH7M DH e CPU Socket Socket M e Front Side Bus 533 667 MHz e BIOS Award PnP Flash BIOS e System Memory m Two x 240 pin DDR2 DIMM sockets m Maximum up to 4GB DDR2 memory Y Note The actual maximum capacity will be less depending on system configuration m Support DDR533 667 memory e L2 Cache integrated in CPU e IDE Interface m One IDE connector and up to two IDE devices Ultra DMA ATA33 66 100 supported e FDD Interface Supports up to two drives e Compact Flash Socket optional m One Compact Flash Type II Socket e Onboard Multi I O Parallel Port one bi directional with ECP EPP SPP support Genial Port one for RS 232 COM1 and one port for RS 232 422 485 COM2 e USB Interface Fou
55. us Menu ENTER Select Figure 6 Configuring SATA for RAID Function 73 SHB110 Socket M Full Size SBC User s Manual 3 5 After setting all the items on the menu select Create Volume and press ENTER as Figure 7 to start creating the RAID array o E Intel R Matrix Storage Manager option ROM v5 7 0 1007 ICH7MR Copyright C 2003 05 Intel Corporation All Rights Reserved CREAT VOLUME MENU Name Volume RAID Level RAIDO Stripe Disks Select Disks Stripe Size 128KB Capacity 1487GB Creat Volume HELF Enter the volume capacity The default value indicates the maximum volume capacity using the selected disks If less than the maximum capacity is chosen creation of a second volume is needed to utilize the remaining space Change TAB Next ESC Previous Menu ENTER Select Figure 7 3 6 When prompting the confirmation press Y to create this volume or N to cancel the creation 8 Intel R Matrix Storage Manager option ROM v5 7 0 1007 ICH7MR Copyright C 2003 05 Intel Corporation All Rights Reserved CREAT VOLUME MENU Name Volume RAID Level RAIDO Stripe Disks Select Disks Stripe Size 128KB Capacity 149 1 GB WARNING ALL DATA ON SELECTED DISKS WILL BE LOST Are you sure you want to creat this volume Y N Press Enter to Creat the specified volume Change TAB Next ESC Previous Menu ENTER Select Figure 8 74 Configuring SATA for RAID Function
56. ver setup Progress Please wait while the following components are installed Copying file ig pun exe Copying file dfvap dl Copying file 15 cr B bmp Copying file Ich BA bmp Copying file HDMIENU dll Creating key HELMS System CurentControls et Controla mdouwzh SystemD irecte Creating key HELMS System CurrentControlSet Senvices ValmD eviceO SystemL Creating key HELM System CurrentControlS et Services ValmD evice SystemL Creating key HELMASOFT WARE SMicrosotthh Wwindows Curent ersion Uninstall Creating key HELMASOFT WARE SMicrosotth Windows Curent ersion Uninstall Installing Driver Intel A 0965 0963 Express Chipset Family Version 6 14 70 4020 Installation has completed Click Mest to continue Intel A Installation Framework 60 Instalation of Drivers SHB110 Socket M Full Size SBC User s Manual 6 You will be asked to reboot your computer when the installation is completed Please click Yes want to restart my computer now if you don t need to install any other drivers Otherwise please click No will restart my computer later and click Finish to complete the installation Intel R Graphics Media Accelerator Driver The setup of the Intel R Graphics Media Accelerator Driver is complete Tou must restart this computer for the changes to take effect Would you like to restart the computer now f Yes want to restart this computer now No wil restart this
57. writing disk Drive A Formatting Wpmg Verity 5 Installing the SATA controller driver during the OS installation Now the SATA driver disk is ready and BIOS settings configured you can proceed to install Windows XP onto your SATA hard drive using the SATA driver Here is an example for Windows XP installation 78 Configuring SATA for RAID Function 5 1 5 2 Windows Setup SHB110 Socket M Full Size SBC User s Manual Restart your system to boot the Windows XP Setup disk and press F6 button as soon as you see the message Press F6 if you need to install a 3rd party SCSI or RAID driver as Figure 11 After pressing the F6 button there will be a few moments for some files being loaded before next screen appears Press F6 if you need to install a third party SCSI or RAID driver Figure 11 When you see the screen below insert the floppy disk containing the SATA driver and press S as Figure 12 Windows Setup setup could not determine the type of one or more mass storage devices installed in your system or you have chosen to manually specify an adapter Currently Setup will load support for the following mass storage devices s lt none gt To specify additional SCSI adapters CD ROM drives or special disk controllers for use with Wiindows including those for which you have a device support disk from a mass storage device manufacturer press 5 If you do not have any device su

1971.4KB - Axiomtek

Contents

Download Pdf Manuals

Related Search

Related Contents