Home

Icom IC-2200H - Orchard City Amateur Radio Club

1. While pushing 4 8 turn power ON Wy CIEE s MW CID Push _ to start cloning master transceiver AT POWER ON While pushing M CALL Ge turn power ON to enter cloning mode mas ter transceiver only power on only for sub transceiver CLONE appears and the transceivers enter the clone standby condition Push S MW QWg on the master transceiver CL OUT appears in the master transceiver s display and the S RF indicator shows that data is being transferred to the sub transceiver CL IN appears automati cally in the sub transceiver s display and the S RF indica tor shows that data is being received from the master transceiver When cloning is finished turn power OFF then ON to exit cloning mode 13 OTHER FUNCTIONS Cloning using a personal computer Data can be cloned to and from a personal computer Mi crosoft Windows 98 98SE 2000 Me XP using the optional CS 2200H CLONING soFTwaRE and the optional OPC 478 RS 232C type or OPC 478U USB type CLONING CABLE Consult the CS 2200H cLONING SsoFTWARE HELP file for de tails OPC 478 to RS 232C port _ Or OPC 478U Microsoft and Windows are registered trademarks of Microsoft Corporation in the U S A and other countries Cloning error A NOTE DO NOT push any key o
2. KEY FUNCTION SECONDARY FUNCTION lt key OTHER FUNCTIONS a Switches between opening and closing the In memory mode switches the channel names wont squelch p 13 or number indication ON and OFF p 30 Azo Starts and stops scanning p 38 Starts and stops tone scanning p 51 SCAN2 a Starts and stops priority watch p 44 Turns the one touch PTT function ON and PRIOS OFF p 16 orcs Selects high output power p 16 Turns the DTCS squelch ON p 50 i Wend k 5 After pushin ws cn Turns the DSQL function p 67 an oe issdins mcs Selects mid output power p 16 Turns the DTCS pocket beep function ON p 49 DTMF code pgs 20 46 uss Turns the DSQL pocket beep function When the DTMF memory en amr Selects low output power p 16 Turns the DTMF memory encoder function coder is activated push 0 to Lows ON p 45 9 to transmit the appropriate X Selects minus duplex operation p 18 Turns the subaudible tone encoder ON DTMF memory contents ery p 18 PRE was Selects plus duplex operation p 18 Turns the CTCSS pocket beep function ON p 49 ouP 8 Turns the CSQL pocket beep function zsa Selects simplex operation p 18 Turns the tone squelch function ON p 50 simp9 Turns the CSQL function p 67 sone No primary function Sends a 1750 Hz tone signal while pushing 9 and holding p 20 While in t
3. PWR SET Melek Push SET KAA several times until the RPT display appears as shown above right USING INITIAL SET MODE Rotate DIAL to turn the auto repeater function to R1 R2 or OFF s ee RP Ex Auto repeater function is Auto repeater function is ON turned OFF tone encoder is ON e R1 auto repeater is ON tone encoder is OFF e R2 auto repeater is ON tone encoder is ON Push PWR to exit initial set mode RP Exe SET MONI Frequency range and offset direction Frequency range 145 200 145 495 MHz u 146 610 146 995 MHz 147 000 147 395 MHz appears Duplex direction appears E General description The transceiver has 207 memory channels including 6 scan edge memory channels 3 pairs and 1 call channel Each of these channels can be individually programmed with operat ing frequency pgs 9 10 duplex direction p 17 and offset p 21 subaudible tone encoder or tone squelch and its tone frequency pgs 19 48 50 and skip information p 41 In addition a total of 10 memory banks A to J are available for usage by group etc except for scan edge memory channels E Memory channel selection Using the tuning dial M CALL Gitte Push CO D2 once or twice to select Q Oee eA memory mode 0 indicator appears IDIAL Rotate DIAL to select Appears the desired memory ch
4. 3 beeps may sound and the VFO contents including the subaudible tone frequency etc are programmed Memory channel number increases when continuing to audible tone encoder ON OFF and its frequency if neces sary 2 Push FUNC then cLr A MW momentarily 3 Select the memory channel to be programmed Push A or V to select the memory channel direct nu meral input cannot be used push ctr A MW after programming EXAMPLE Programming 145 870 MHz into memory channel 20 blank channel via the microphone Push 2 Push 9 28 Ea ee Se a a Push then 4 momentarily yo EAN YC A YGF Ara iant i iali iki D uianda alc ep Gu ap op cw am ap Gy G43 GT 7 SET MONI LOW TONE M CALL V MHz SET MONI LOW TONE M CALL V MHz SET MONI LOW TONE M CALL ViMHz Push then 1 sec and continue to push 1mm LA pa u u r u u Pelino ITA l aMi TA se az CE erage IY Ay amp eZ GIJ EY qu ED Gis eA qu ED Ge EW SET MONI Low TONE M CALL ViMHz SET MONI Low TONE M CALL V MHz SET MONI LOW TONE M CALL V MHz 26 5 MEMORY OPERATION E Transferring memory contents This function transfers a memory channel s contents to VFO or another memory call channel This is useful when search ing for signals around a memory channel frequency and for recalling the offset frequency subaudible tone frequency etc Memory
5. Push MONI or SET to set into call sign programming con dition e The 1st digit blinks and channel indication stops blinking Rotate DIAL to set the desired character or code e Push MONI or SET to move the cursor to left or right re spectively Push MONI or SET to select 2nd digit then rotate DIAL to set the desired character or code e 2nd digit blinks 1st digit stop blinking e Repeat this step for programming station repeater call sign v Veet T L S f SET nbn v MHz Push V MHz to fix the call sign Rotate DIAL to select an another channel from C1 to C6 Repeat steps to to program another station repeater call sign channels Y For your information Station and or repeater call sign can be programmed from Received call record when a call is received See page 64 for details Y For your information Repeater call sign can be programmed gateway connection capabilities at step for connecting to the other Area or Zone G appears or disappears at the 8th digit when each pushing LOW DIGITAL MODE OPERATION 12 Push BANK OPTION for 1 sec then push BANK OPTION or MR CALL to select the call sign select mode e YUC appears for station call sign e R1C or R2C appears for repeater call sign Push A or V to select the desired call sign channel then push set B D OFF Push set B D
6. 74 13 OTHER FUNCTIONS Display dimmer Adjust to suit lighting conditions The levels 1 dark to 4 bright default are available Display color The display color can be set to amber default or green 1 Tone squelch tone Sets subaudible tone frequency both encoder and decoder for tone squelch operation Total of 50 tone frequencies 67 0 254 1 Hz are available default 88 5 Hz e Available subaudible tone frequencies 67 0 79 7 94 8 110 9 131 8 156 7 171 3 186 2 203 5 229 1 69 3 82 5 97 4 114 8 136 5 159 8 173 8 189 9 206 5 233 6 71 9 85 4 100 0 118 8 141 3 162 2 177 3 192 8 210 7 241 8 74 4 88 5 103 5 123 0 146 2 165 5 179 9 196 6 218 1 250 3 77 0 91 5 107 2 127 3 151 4 167 9 183 5 199 5 225 7 254 1 NM it I RI INS m SET MONI SET MONI Amber setting default Green setting Repeater tone Sets subaudible tone frequency encoder only for repeater operation Total of 50 tone frequencies 67 0 254 1 Hz are available default 88 5 Hz noys Z ich aan DI LM l el DTCS code and polarity Sets DTCS code both encoder and decoder for DTCS squelch operation Total of 104 codes are available default 023 DTCS polarity Sets DTCS polarity for transmission and reception from NN NR RN RR
7. Push M CALLGGile several times to select the call channel e C appears Push S MW I momentarily then rotate DIAL to se lect the memory channel to transfer the contents to 0 indicator and memory channel number blink To transfer to the VFO push S MW RMY for 1 sec Push S MW Md for 1 sec to transfer when a momen tary push was used in the previous step If channel names have been programmed into the call channel the names are also transferred fy 1 Push MR CALL for 1 sec to select the call MR CALL channel Ney 2 Push FUNC ctr A MW momentarily ae then push A W to select the memory MW channel to transfer the contents to e To transfer to the VFO push FUNC then push EA cLr A MW for 1 sec gt Z w lt lt Push FUNC then ctr A MW for 1 sec to transfer when a momentary push was used in the previous step If channel names have been programmed into the call channel the names are also transferred CALL CHANNEL OPERATION 6 E Programming a call channel Operating frequency duplex information subaudible tone in Push S MW Qi for 1 sec to program formation tone encoder or tone squelch ON OFF and its fre 3 beeps sound and the unit returns to VFO mode automatically quency and alphanumeric channel names can also be programmed into the call channel f 1 Set the desired frequenc
8. 12 DIGITAL MODE OPERATION Your call sign programming continued 1 Push BANK OPTION for 1 sec then push BANK OPTION or MR CALL to select the call sign select mode e MYC appears 2 Push A or V to select the desired call sign channel then push set B D OFF 3 Push set B D OFF to set into call sign programming mode e The 1st digit blinks and channel indication stops blinking 4 Push A or V to set the desired charac ter or code e Push set B D OFF or Ent C T OFF to move the cursor to left or right respectively 5 Push set B D OFF or Ent C T OFF to select 2nd digit then push A or V to set the desired character or code e 2nd digit blinks 1st digit stops blinking e Repeat this step for programming your call sign 6 Push ctr A MW to fix the call sign and exit programming condition eras BANK OPTION Station Repeater1 2 call sign programming Station call sign must be programmed for the specified sta tion call as well as repeater operation in both Digital voice and slow data communications Push BANK A for 1 sec then push BANK A or V MHz several times to select the call sign select mode e YUC appears for station call sign e R1C or R2C appears for repeater call sign SET MONI v MHz Rotate DIAL to select the desired call sign channel then push SET or MONI
9. me O 7 gt to n O o DIGITAL PRIO AO BUS ii ns NAR IWA WWA INA IAL IAL NA a wo JANI TANT WAN WANT JAN Mant EE LOW TONE M CALL T SCAN Gir SCAN V MHz 10 arp OB C SET MONI Sao O POWER KEY PWR Turns power ON and OFF when pushed for 1 sec MEMORY WRITE KEY S MW DIH p 25 Selects a memory channel for programming Programs the selected memory channel when pushed for 1 sec e Continue to hold the key to increment the memory channel automatically Eaj DEE n sankan pEcpcag MICROPHONE CONNECTOR Connects the supplied microphone VOLUME CONTROL VOL p 13 Adjusts the audio level SQUELCH CONTROL SQL p 13 Varies the squelch level The RF attenuator activates and increases the attenuation when rotated clockwise to the center position and further SET LOCK KEY SET KJ Enters set mode when pushed p 74 Keys the lock function ON and OFF when pushed for 1 sec p 12 MONITOReCHANNEL NAME KEY MONIEN Push to switch the monitor function ON and OFF p 13 In memory and call channel mode switches the channel names or number ON and OFF p 29 OUTPUT POWER DUPLEX KEY LOW PIA Each push changes the output power selection p 16 Select DUP DUP and simplex operation when pushed for 1 sec p 17 TONEs TONE SCAN KEY TONE ER Each
10. 1 Push MR CALL to select memory mode Push BANK OPTION to select memory bank condition e Bank initial blinks Push A V to select the desired bank A to J e Only programmed memory bank can be se lected Push cir A MW to set the bank e Initial stops blinking Push A V to select the desired con tents in the bank e No channel numbers are displayed for memory bank operation To return to regular memory condition push BANK OPTION then cLr A MW 5 MEMORY OPERATION E Memory bank setting Push M CALL HE to select memory mode then se lect the desired memory channel via DIAL Push SET KAA enter the set mode 3 Push SET or MONI several times until BAK appears e indication blinks as follows YN AHbexs a SET MONI mm Rotate DIAL to select the desired bank to be set a BAKE Aw Owmpooooo j OSSseqq SET MONI DIAL Push any key other than SET or MONI to set the chan nel into the bank and return to regular memory condition Repeat steps to to set another memory channel into the same or another bank Push MR CALL then select the desired memory channel via A V or keypad Push set B D OFF to enter set mode Push set B D OFF or Ent C T OFF several times until BAK appears Push A or
11. F 2 keys on HM 133V The following conditions can be memorized into F 1 and F 2 keys independently e Operating frequency e Repeater setting offset direction and frequency tone ON OFF and frequency Tone DTCS squelch ON OFF frequency code and polarity e Transmit output power selection e Set mode settings e Initial set mode settings except display type item Programming the condition Set the desired contents of each condition then push F 1 F 2 for 1 sec 3 beeps sound F 1 F 2 Re calling the condition Push F 1 F 2 momentarily OTHER FUNCTIONS 13 UP DN keys on a microphones other than HM 133V ar POWER ON The following functions are assigned to the UP DN keys on the other microphones HM 118N TAN etc when first ap plying power UP channel up push and hold to start scan push again to stop scan DN channel down push and hold to start scan push again to stop scan Assigning a function Turn the power OFF While pushing the desired key on the transceiver and one of either UP DN keys on the microphone turn the power ON e The function is programmed into the key Clearing an assignment Turn the power OFF While pushing the desired UP or DN key on the micro phone turn the power ON 13 OTHER FUNCTIONS E Partial reset If you want to initialize the operating conditions VFO fre quency VFO settings set mode contents without
12. Push PTT to transmit the pager code Wait for an answer back e When the transceiver receives an answer back code the function display shows the other member s ID or group code After confirming a connection push BANK OPTION for 1 sec then push A V to select the code squelch opera tion or repeat the previous key operation again to select non selective calling sys tem Communicate with the other party as nor mal push PTT to transmit release to re ceive Waiting for a call from a specific station Set the operating frequency Push BANK 0 for 1 sec then rotate DIAL to turn Pager mode ON e 100 MHz digit shows P Wait for a call e When receiving a call the caller s ID or group code appears as shown at right Push PTT to send an answer back call and display the operating frequency After confirming a connection push BANK A for 1 sec then rotate DIAL to select code squelch operation or repeat the previous key operation again to select non selective calling system Er Set the operating frequency BANK OPTION 2 Push BANK OPTION for 1 sec then push A V to turn Pager mode ON 100 MHz digit shows P Wait for a call When receiving a call the caller s ID or group code appears as shown at right DO NOT push any digit keys while code chan nels CO to C6 are displayed or code channel contents will be changed 4 Push PTT to send an an
13. default NN Offset frequency Sets the duplex offset frequency within 0 to 20 MHz range During duplex repeater operation transmit frequency or re ceive when reverse function is set to ON shifts the set fre quency default value may differ depending on versions Reverse mode Sets the reverse function ON and OFF default SET MONI SET MONI Reverse function OFF default Reverse function ON Tuning step Selects tuning step from 5 default 10 12 5 15 20 25 30 and 50 kHz for DIAL or 4 operation Lit ar I Ls SET MONI OTHER FUNCTIONS 13 Scan resume timer Selects scan resume timer from SCT 15 default SCT 10 SCT 5 and SCP 2 e SCT 15 10 5 Scan pauses for 15 10 5 sec then re sumes Pause on a signal until signal disap pears then resumes 2 sec after the sig nal disappears e SCP 2 Transmit permission Turns transmission permission ON and OFF This function can be set for each memory call channel and VFO indepen dently SET MONI SET MONI Transmission is permitted Transmission is inhibited default 13 OTHER FUNCTIONS Channel skip setting Sets channel skip setting from ON and OFF for memory skip scan operation This item appears when set mode is accessed from memory mode only DHSMSIE a HSIN ana SET MONI SET MONI c Scans the memory channel does not skip default
14. Call sign programming Push TONE IEAA several times until w or ap pears in the function display Dn for digital code squelch for call sign squelch operation When a signal with the matched digital code call sign is re ceived the squelch opens and the signal can be heard e When the received signal includes an unmatched digital code call sign the squelch does not open However the S RF indicator shows the received signal strength To open the squelch manually rotate SQL counter clockwise Operate the transceiver in the normal way push PTT to transmit release PTT to receive To cancel the digital code call sign squelch push TONE BEST several times until mn or disappears NOTE While in the digital mode operation the monitor Z function pushing MONIEZYQII works as the analog mon Z itor for receiving an FM signal The digital monitor function Z is activate using the Squelch control knob SQL MQ 1 Set the operating frequency TSQL 2 Program the digital code or call sign in setting mode e See p 69 Digital code setting or pgs 59 60 Call CA sign programming DTCS 3 Push FUNC then simp 9 TSQL or HiGH 4 DTCS to turn the digital code or call sign squelch ON 4 When a signal with the matched digital code or call sign is received the squelch opens and the signal can be heard e When the received signal includ
15. L DIGITAL MODE OPERATION 12 Auto RxCall Write When an individual station call is received the calling station call sign can be stored automatically The stored call sign can be re called when selecting a station call sign default OFF Auto Rx RepeaterCall Write When an individual station call via the repeater is received the repeater call sign can be stored automatically The stored repeater s call sign can be re called when selecting a re peater call sign default OFF Hp 12 DIGITAL MODE OPERATION Message Transmission Select the Message transmission function ON and OFF When ON is selected transceiver transmits a text message pre programmed default OFF After the manual transmission pushing PTT the Message Transmission setting is return to OFF automatically TX message TX messages are available up to 6 channels and each chan nel can be programmed up to 20 characters message Avail able characters are 0 to 9 A to Z capital letters only some symbols and space shown at right table DIGITAL TX message programming ATX message channel C1 must be programmed if you want to use the GPS message The GPS message is transmitted from channel C1 only Push MONI or SET to edit for 1 sec then rotate DIAL to select the message channel One of either C1 to C6 flashes Push MONI or SET to set into message pro
16. ee Push BANK OPTION then select the de wy sired memory bank via A V Push ctr A MW to select the bank then i eae select the desired contents via A V Push set B D OFF to enter set mode 3 Push set B D OFF or Ent C T OFF sev eral times until BAK appears 4 Push A V to select the desired bank initial to transfer or erase e Select indication when erasing the contents from the bank 5 Push ctr A MW to set the bank and exit set mode 6 Repeat steps 1 to 5 for transferring or eras ing an another banks contents lt O 6 CALL CHANNEL OPERATION E Call channel selection E Call channel transferring Push M CALL Gaile once or twice to select the call channel C appears instead of mem ory channel number indication Appears Push M CALL all to re ee turn to memory mode or push LIE PATATA 1 V MHz RAN to select VFO BE PEA AVATA L mode qu SCAN cio EZD Push MR CALL for 1 sec to select the call MR CALL channel Push MR CALL to select memory mode or push VFO LOCK to select VFO mode Y INFORMATION Small c shows VEO was When the VFO mode is se selected from the call channel lected from the call channel a small c appears instead H E DADANA ne of memory channel number MONI oe brant V MHz 35
17. respectively After checking a received position and message push any key other than indicated function keys to return to normal operating mode E Set mode e Set mode operation Push SET HeJei4 to enter the set mode Push SET or MONI to select the desired item Rotate DIAL to select the condition or value Push any key other than SET or MONI to exit set mode e Set mode items e Display dimmer JIM 4 e Weather alert HL i OR h H F FM e Wide Nar setting A IIN I Ws INT IN N e Bank link function LK HOF Ee e AM FM mode select OTHER FUNCTIONS 13 EE Push set B D OFF to enter set mode o m A N Push set B D OFF or Ent C T OFF to select the desired item w Push A or V to select the condition or value gt Push ctr A MW to exit set mode Repeater tone frequency gt Push 4 cer front panel or gt Push 4 wom front panel or e Tone squelch E a Available for USA version only tAppears when accessing set mode from VFO mode only Appears when accessing set mode from memory mode only e Tuning step T55 e Channel skip setting e Scan resume timer 4 A Bank setting LHS rs HF ang e Transmit permission aL qT bp be S JAK aS oe Ne microphone microphone dt e DTCS polarity SITP NN Orsel frequency Movi e Reverse mode y A yee OF
18. to select the J Memory call gt call memory Select the memory call channel to be transferred Push M CALLGjile to select memory mode then ro tate DIAL to select the desired memory channel Push M CALL A0 for 1 sec to select the call channel Push S MW QWg momentarily D Mi O gt cr m JCJ bape beens r Il channel e D indicator and indication blink and shows VFO condi A ca i tions I we 2 Push FUNC then cLr A MW momentarily 0 indicator and indication blink and shows Rotate DIAL to select the target memory channel VEO conditions e C blinks when the call channel is selected 3 Push A V to select the target memory e Scan edge channels 1A 1b 2A 2b 3A 3b can also be selected chann l Push S MW M for 1 sec to transfer the selected mem DAIIRA ory call channel contents to the target memory Or blinks when th call channel is Selected ae e Scan edge channels can also be selected The targeted memory and transferred contents are indicated The keypad cannot be used for the selection 4 Push FUNC then push ctr A MW for 1 sec to transfer the selected memory call channel contents to the target memory The targeted memory and transferred contents are indicated EXAMPLE Transferring memory channel 30 contents to channel 31 Front panel operation s MwW OD s MwW OD Select the
19. to select the blank channel or erasable channel Push BANK egg three times to select the received call in dication To confirm the received call push SET or MONI to enter the received call sign indication mode DIGITAL N AN KEB YF S SET MONI E tu k Push S MW QW for 1 sec to store the call sign into the selected station call sign channel Push and hold PTT to reply a call en BANK OPTION N w gt o DIGITAL MODE OPERATION 12 Push BANK OPTION or MR CALL to select the call sign select mode e YUC appears for station call sign e R1C or R2C appears for repeater call sign Push A or V to select the blank chan nel or erasable channel Push BANK OPTION three times to select the received call indication To confirm the received call push set B D OFF or Ent C T OFF to enter the received call sign indication mode Push FUNC then cir A MW for 1 sec to store the call sign into the selected sta tion call sign channel Push and hold PTT to reply a call 12 DIGITAL MODE OPERATION E Break in communication The break in function allows you to break into an another sta tions communications in both Digital voice and slow data op eration While receiving an another stations communication push BANK e 34g for 1 sec to enter the option set mode then set the either station repeate
20. weather channel is checked periodically during standby or while scanning U S A versions only Select the desired weather channel Turn the weather alert function ON in set mode Push SET eJe to enter set mode Push SETKA or S MW WY to select the weather alert item then rotate DIAL to set ON Push TONE BERYe WN to exit set mode Sets the desired stand by condition e Selects VFO memory or call channel e Scan or priority watch operation can also be selected When the alert is detected a beep sounds and the follow ing indication will be displayed AT ee Se co en qs eg T SCAN SCAN SET MONI LOW TONE M CALL V MHz SET MONI LOW TONE M CALL V MHz Shows above indications alternately Turn the weather alert function OFF in set mode Y NOTE While receiving a signal on a frequency other than Z the weather alert ON frequency the receiving signal or A audio will be interrupted momentarily every 5 sec approx Y in case the alert function is turned ON This symptom is Y caused by the WX alert function To cancel these symp 7 toms set the weather alert item OFF in set mode E Microphone keys The supplied HM 133V s optional for some versions F 1 and F 2 keys memorize the transceiver conditions The UP DN keys of the standard or an optional micro phone other than the HM 133V can be assigned functions like the function keys on the transceiver s front panel F 1
21. 2 allen socket bolts from the front panel using with an allen wrench 2 5 mm 40 Allen socket Attach the insulation sheet supplied as accessory to IC on the Front unit Remove the protective paper attached to the bottom of the optional unit to expose the adhesive strip Install the unit as illustrated below Insert tightly to avoid bad contact Flat cable Insulation sheet Return the front panel and the allen socket bolts to their original position NOTE When attaching the front panel to the main unit ZG make sure the flat cable are running in the groove to ZY prevent catching between front panel and main unit BP X cE 16 DECLARATION O ICOM OF CONFORMITY We Icom Inc Japan 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive 1999 5 EC and that any applicable Essential Test Suite measurements have been performed Kind of equipment FM TRANSCEIVER Type designation l C 2200H Version where applicable This compliance is based on conformity with the following harmonised standards specifications or documents i EN 301 489 1 v 1 3 1 2001 09 ii EN 301 489 15 v 1 1 1 2000 09 iii EN 301 783 v 1 1 1 2000 09 CEO D sseldorf 8th Dec 2003 Place and date of issue Icom Europe
22. 233 6 71 9 85 4 100 0 118 8 141 3 162 2 177 3 192 8 210 7 241 8 74 4 88 5 103 5 123 0 146 2 165 5 179 9 196 6 218 1 250 3 77 0 91 5 107 2 127 3 151 4 167 9 183 5 199 5 225 7 254 1 DTMF tones DTMF S Push DTMF S then push the keys of the de sired DTMF digits e The function indicator lights green 0 9 A D E and F are available When d is displayed in place of the 100 MHz digit cancel the DTMF memory encoder in advance p 46 e Push DTMF S again to return the keypad to nor mal function control e The transceiver has 10 DTMF memory channels for autopatch operation See p 45 for details Da Push ones i then push desired keys REPEATER OPERATION 4 1750 Hz tone The microphone has 1750 Hz tone capability used for ring tone when calling etc TONE 1 N F TONE 2 Push FUNC e The function indicator lights orange Push TONE 1 to transmit a 1750 Hz tone call signal for 0 5 sec push and hold 0 TONE 2 to transmit a 1750 Hz tone call signal for an arbitrary period e The function indicator goes out automatically 4 REPEATER OPERATION USING SET MODE E Offset frequency When communicating thorough a repeater the transmit fre quency is shifted from the receive frequency by an amount determined by the offset frequency Push
23. A ctr A MW B set B D OFF C Ent C T OFF D sa_a D MUTE E TONE 1 F sacv 16KEY L e Automatically transmits without pushing PTT e The first code one of A to F is not transmitted DTMF code transmission starts from the 2nd code Push DTMF S again to deactivate the DTMF direct selection Q DTMF MEMORY ENCODER E DTMF speed USING INITIAL SET MODE The rate at which DTMF memories send individual DTMF characters can be set to accommodate operating needs Sane nce The display shows the my T fastest DTMF speed is Ah ges l selected BSmeo OL Push PWR for 1 sec to turn power OFF While pushing SET KIX push PWR for 1 sec to turn power ON and enter initial set mode Push SET or MONI several times until DTD appears as shown above Rotate DIAL to select the desired speed as shown in the table below Push PWR to exit initial set mode DISPLAY INTERVAL SPEED DTD 1 100 msec 5 0 cps DTD 2 200 msec 2 5 cps DTD 3 300 msec 1 6 cps DTD 5 500 msec 1 0 cps cps characters sec POCKET BEEP AND TONE SQUELCH 0 E Pocket beep operation This function uses subaudible tones for calling and can be used as a common pager to inform you that someone has called while you were away from the transceiver Waiting for a call from a specific station Set the operating frequency Push SE
24. Connect a microphone to the eight pin modular socket on the front panel of the transceiver HM 133V A different microphone may be supplied with some versions of the IC 2200H E Your first contact Now that you have your IC 2200H installed in your car or shack you are probably excited to get on the air We would like to take you through a few basic operation steps to make your first On The Air an enjoyable experience 1 Turning ON the transceiver Before powering up your IC 2200H you may want to make sure the audio volume and squelch level controls are set in 9 10 o clock positions OOOO Set both VOL and SQL controls to 9 10 o clock positions Although you have purchased a brand new transceiver some settings may be changed from the factory defaults because of the QC process Resetting the CPU is necessary to start from factory default LG PWR SETIROGN SMW i While pushing SET IKA and S MW MMM push PWR for 1 sec to reset the CPU OoOO QUICK REFERENCE GUIDE 2 Tune the desired frequency DIAL will allow you to dial in the frequency you want to op erate Pages 9 and 11 will instruct you on how to set the tun ing speed O f LJOS DIAL Using the HM 133V You can directly enter the frequency with the HM 133V keypad EXAMPLE Setting f
25. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury DO NOT push the PTT when not actually desiring to transmit DO NOT allow children to play with any radio equipment con taining a transmitter During mobile operation DO NOT operate the transceiver without running the vehicle s engine When the transceiver s power is ON and your vehicle s engine is OFF the vehicle s bat tery will soon become exhausted BE CAREFUL the transceiver will become hot when op erating it continuously for long periods AVOID placing the transceiver against walls or putting any thing on the top of the transceiver This will obstruct heat dissi pation AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below 10 C 14 F or above 60 C 140 F AVOID the use of chemical agents such as benzine or alcohol when cleaning as they can damage the transceiver s surfaces USE icom microphones only supplied or optional Other man ufacturer s microphones have different pin assignments and may damage the transceiver if attached SUPPLIED ACCESSORIES AND OPTIONS E Supplied Accessories E Options Microphone HM 133V 0 0 eee eee 1 UT 108 DTMF DECODER UNIT Fuse 20 A ocean bane a een dee res 1 UT 115 DIGITAL UNIT DC power cable SM wie Atay Din hed Rone pecited ead 1 HM 118TAN TN DTMF MICROPHONES Mobile mounting br
26. Programming memory channels The IC 2200H has a total of 207 memory channels including 6 scan edges and 1 call channel for storing often used oper ating frequency repeater settings etc 1 Setting a frequency In VFO mode set the desired operating frequency with re peater tone and tuning steps etc 2 Selecting a memory channel Momentarily push S MW DIMA then rotate DIAL to select the desired memory channel 0 indicator and memory channel number blink f C Waa Gut Gast eg 0 Ir AN m a Oeae P oo oF SP r w S MW DIAL 3 Writing a memory channel Push and hold S MW DA for 1 sec to program 3 beeps sound e Memory channel number automatically increases when continuing to push S MW RAM after programming QUICK REFERENCE GUIDE Using the HM 133V In VFO mode set the desired operating frequency includ ing offset direction tone settings etc Push FUNC then cir A MW QQ indicator and memory channel number blink B22 Push Gro ee mw w BBDO then a gD aBa uy T SET MONI LOW TONE M CALL V MHz 3 Push A V to select the desired memory channel Push FUNC then push ctr A MW for 1 sec to pro gram 3 beeps sound e Memory channel number automatically increases when continu ing to push cLR A MW after programming Vi 1 e E Front panel PANEL DESCRIPTION Function eee O o O p 3
27. call record automatically See page 63 for details 12 DIGITAL MODE OPERATION E When receiving a Digital call When an individual station call is received the calling station call sign can be stored into the received call record The record is cleared once turning power OFF Received call record Push BANK jg for 1 sec then push BANK egg or V MHz several times to select the received call indication RXCALL R1CALL and R2CALL are available for the re ceived station call sign repeater 1 2 call signs respectively DIGITAL gt A X r _ 1 m aad j i SET MONI V MHz To confirm the received call push SET or MONI to enter the received call sign indication mode EG TEA See SET MONI is vim rn BANK OPTION z N Push BANK OPTION for 1 sec then push BANK OPTION or MR CALL to select the received call indication e RXCALL R1CALL and R2CALL are avail able for the received station call sign repeater 1 2 call signs respectively To confirm the received call push ser B D OFF or ent C T OFF to enter the received call sign indication mode To reply a call Push BANK gqgi or V MHz several times to select the call sign select mode e YUC appears for station call sign e R1C or R2C appears for repeater call sign DIGITAL Rotate DIAL
28. clock and fully clockwise position When setting the squelch from the microphone a level greater than 19 activates the squelch attenuator Noise squelch Squelch threshold Squelch is Y Squelch open attenuator Shallow Deep NOTE The squelch attenuator functions even when the monitor function is in use Thus set the SQL within 10 to 12 o clock position 12 to 19 level when setting with the HM 133V is recommended when using the monitor func tion WA 14 3 BASIC OPERATION E S meter squelch USING INITIAL SET MODE The transceiver has an S meter squelch The S meter squelch allows you to set minimum signal level needed to open the squelch Turn the transceiver power OFF While pushing SET KIIA push PWR for 1 sec to enter initial set mode PWR SET elena Push SET or MONI to select SSQ S meter squelch item Rotate DIAL to set the S meter level or OFF it 4 ats Lures 0 OPES SSRF AAFAA S meter squelch OFF default S2 level 2 indicator level Push PWR to exit initial set mode E Transmitting CAUTION Transmitting without an antenna will damage the transceiver Y NOTE To prevent interference listen on the channel be G tore transmitting by pushing MONIY or moni 1 ANM on the microphone Set the operating frequency pgs 9 10 e Select output power if desired See section at right for d
29. formatters 1 GLL 6 GLL GGA 11 GGA GSA 16 GLL GGA RMC 21 GLL GSA VTG 2 GGA 7 GLL RMC 12 GGA VTG 17 GLL GGA GSA 22 GGA RMC GSA 3 RMC 8 GLL GSA 13 RMC GSA 18 GLL GGA VTG 23 GGA RMC VTG 4 GSA 9 GLL VTG 14 RMC VTG 19 GLL RMC GSA 24 GGA GSA VTG 5 VTG 10 GGA RMC 15 GSA VTG 20 GLL RMC VTG 25 RMC GSA VTG DIGITAL MODE OPERATION 12 Push BANK AF twice to select the position indication MV TE MY PES SET MONI V MHz Push MONI or SET to enter the position indication e Latitude and longitude date appear in order as below SET f MONI North or South Degrees Minutes Seconds Push 4 s gt Push 4 nom DIGITAL DIGITAL bse NE aa ran t ta gt J viMHz SET A MONI East or West Degrees at Ly SET MON Minutes Seconds After checking the current position push any key other than indicated function keys to return to normal operating mode IMPORTANT When set the sentence formatter at step for connecting GPS receiver and already programmed your call sign GPS automatic transmission is activate every 3 minutes The automatic transmission can be changed inter val time or deactivated if desired see next page RB QW 72 12 DIGITAL MODE OPERATION GPS Automatic transmission While connecting a GPS receiver push BANK 0A for 1 sec to enter the option set mode Push BANK gag or V M
30. is activated default RP The repeater lockout is turned ON BU _ The busy lockout is turned ON RL LHP SET MONI SET MONI Busy lock out setting Repeater lock out setting Squelch delay Selects squelch delay from short and long to prevent re peated opening and closing of the squelch during reception of the same signal S Short squelch delay default eL Long squelch delay ie Tr TMT TENS _l I SET MONI SET MONI nt L Na cre aN lz Short squelch delay setting Long squelch delay setting S meter squelch Selects S meter squelch threshold level from OFF and 1 S7 This setting allows you to set a minimum signal level needs to open the squelch 5569F S meter squelch OFF default m VI SET MONI S2 level 2 indicator level DTMF speed The rate at which DTMF memories send individual DTMF characters can be set to accommodate operating needs 1 100 msec interval 5 0 cps speed default 2 200 msec interval 2 5 cps speed 3 300 msec interval 1 6 cps speed 05 500 msec interval 1 0 cos speed TT Te l Ui drS l Display type Selects LCD indication type from frequency channel number and channel names FR Shows frequency default CH _ Shows channel number NM _ Shows channel names Programmed memory channels only can be selected Frequency indication setting Memory channel name indication
31. p 12 PTT SWITCH Push and hold to transmit release to receive Switches between transmitting and receiving while the one touch PTT function is in use p 16 PANEL DESCRIPTION 1 UP DOWN KEYS A V Push either key to change operating frequency mem ory channel set mode setting etc pgs 10 24 Push either key for 1 sec to start scanning p 38 O ACTIVITY INDICATOR Lights red while any key except FUNC and DTMF S is pushed or while transmitting Lights orange while the microphone keypad lock func tion is activated Lights green while the one touch PTT function is in use OKEYPAD pgs 7 8 FUNCTION INDICATOR Lights orange while FUNC is activated indicates the secondary function of keys can be accessed Lights green when DTMF S is activated DTMF sig nals can be transmitted with the keypad FUNCTION KEY FUNC pgs 7 8 DTMF MEMORY SELECT KEY DTMF S p 46 O FUNCTION KEYS F 1 F 2 p 84 Program and re call your desired transceiver conditions BANK OPTION KEY BANK OPTION Push to selects memory bank condition during memory mode p 32 Push for 1 sec to enter the DTMF or option set mode MEMORY CALL KEY MR CALL Push to select memory mode p 24 Push for 1 sec to select call channel p 35 6 N 1 PANEL DESCRIPTION E Microphone keypad
32. push selects a tone function pgs 17 48 Tone encoder pocket beep tone squelch or tone function OFF can be selected Push for 1 sec to start stop the tone scan function p 51 O While in the digital mode operation with the installing an optional Digital unit UT 115 Each push select the digital code CSQL squelch func tion call sign DSQL squelch pocket beep function CSQL or DSQL p 67 O MEMORY CALL PRIORITY KEY M CALLGGie Push to select and toggle memory call and weather channel modes pgs 24 35 83 Weather channels available for USA versions only Starts priority watch when pushed for 1 sec p 44 PANEL DESCRIPTION 1 VFO MHz TUNING SCAN KEY V MHz KA AN Selects and toggles VFO mode and 1 MHz or 10 MHz for some versions tuning when pushed p 9 Starts scan when pushed for 1 sec p 38 Cancels a scan when pushed during a scan BANK OPTION KEY BANKKA Push to select memory bank condition during memory mode p 32 Push for 1 sec to enter the DTMF or option set mode TUNING DIAL DIAL Selects the operating frequency p 9 memory channel p 24 the setting of the set mode item and the scanning direction p 38 Microphone connector front panel view 8 V DC output Max 10 mA Channel up down 8 V control IN PTT GND microphone ground MIC microphone input GND Data IN i w 1 PANEL DESCRIPTI
33. receiving ue fy HI 4g a a signal on the memory or l A i by pat Sua a eg Call channel PRIO blinks SET MONI Low TONE M CALL V MHz v 3 O e N gt PRIORITY WATCH 8 Select VFO mode then set an operating fre quency Set the watching channel s For memory channel watch Push MR CALL then A or V to select the desired memory channel For memory scan watch Push MR CALL then push scan 2 to start the memory scan For call channel watch Push MR CALL for 1 sec to select the call channel Push PRIo 3 PTT M to start the watch e The transceiver checks the memory or call channel every 5 sec e The watch resumes according to the selected scan re sume condition p 42 e To resume the watch manually when paused push PRIo 3 PTT M or ctr A MW To stop the watch push cLr A MW 44 9 E Programming a DTMF code DTMF codes are used for autopatching controlling other equipment etc The transceiver has 16 DTMF memory chan nels d0 dF for storage of often used DTMF codes of up to 24 digits Push BANK for 1 sec to enter the DTMF setting Rotate DIAL to turn the DTMF encoder ON Push SET or MONI to enter the DTMF programming condition e Push V MHzZ to return to the DTMF setting Rotate DIAL to select the desired DTMF memory chan nel The DTMF memory channel indi
34. setting OTHER FUNCTIONS 13 Squelch attenuator Turns the squelch attenuator function ON and OFF ON The squelch attenuator activates when SQL control is set between 12 o clock and fully clockwise position default OF The squelch attenuator does not function H T TZIN H T TaI 1 isiti 1 PE ALC function Sets the ALC Automatic Level Control function ON and OFF default The ALC function reduces the microphone gain automatically when the transmission audio is distorted HL Lei SET MONI ALC function OFF default ALC function ON 13 OTHER FUNCTIONS E Weather channel operation Weather channel selection Push M CALL QEA sev eral times to select weather channel group Rotate DIAL to select the desired weather channel W Push M CALLEGHI to ca select memory mode or push V MHz A A to se LOCK qn SCAN SET MONI LOW TONE M CALL V MHz lect VFO mode UUU ST O es S Osscoec Weather alert function NOAA broadcast stations transmit weather alert tones before important weather announcements When the weather alert function is turned ON the selected weather channel is moni tored each 5 sec for the announcement When the alert sig nal is detected the AL T and the WX channel are displayed alternately and sounds a beep tone until the transceiver is op erated The previously selected used
35. the desired item 2 Rotate DIAL to select the desired value or condition Push BANK OPTION for 1 sec then push BANK OPTION or MR CALL sev eral times to select the desired item Push A or V to select the desired value or condition E BANK OPTION N Auto Reply During Digital mode operation auto reply function is avail able This function replys to an individual station call even you are away from the transceiver default OFF After the manual transmission pushing PTT the Auto Reply setting is return to OFF automatically Digital Code Sets the desired digital code for digital code squelch opera tion Total of 100 codes 00 99 are available default 00 Auto data Transmission During slow data operation auto data transmission function is available This function transmits when data are input from PC via the DATA jack default OFF After the manual transmission pushing PTT the Auto Transmission setting is return to OFF automatically DIGI AT x ETF ss An NZ Data Speed Select the communication speed between the transceiver and PC from 4800 baud or 9600 baud default 9600 Standby Beep Turns the beep emission capability when the communicating station finishes transmitting or the receive signal disappears default OFF ITAL Te 7 lr is iy Li j T Bf I ING A Va D e ll
36. the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury NEVER place the transceiver where air bag deployment may be obstructed DO NOT place the transceiver where hot or cold air blows di rectly onto it AVOID placing the transceiver in direct sunlight Using the mounting bracket Drill 4 holes where the mounting bracket is to be installed e Approx 5 5 6 mm 14 when using nuts approx 2 3 mm when using self tapping screws Insert the supplied screws nuts and washers through the mounting bracket and tighten Adjust the angle for the clearest view of the function dis play Mounting When using an self tapping a screws Mounting Spring washer IMPORTANT Detailed installation notes for Icom mobile transceivers to be fitted into vehicles are available Contact your Icom dealer or distributor RA A Battery connection t NEVER connect the transceiver directly to a 24 V battery DO NOT use the cigarette lighter socket for power con nections See p 5 for details Attach a rubber grommet when passing the DC power cable through a metal plate to prevent short circuiting e CONNECTING TO A DC POWER SOURCE e See p 90 for fuse replacement IC 2200H red black Fuses 20A Supplied DC power cable NOTE Crimp J 2 Qiier Use terminals for the G P cable c
37. to locate new stations for contact or listening purposes operating needs FULL SCAN p 38 Repeatedly scans all frequen PROGRAMMED SCAN Repeatedly scans between cies over the entire band p 38 two user programmed fre Band Band Used as the simplest scan quencies Used for checking edge ede without any preliminary set for frequencies within a speci Band Scan edges Band E tings necessary edge a RN edge fied range such as repeater swx gt LAH output frequencies etc 3 nuuste pairs of scan edges are avail Jump able eee Repeatedly scans memory SCAN RESUME 4 resume conditions are avail channels except those set as CONDITION p 42 able 3 timer scans and pause skip channels Used for often scan When receiving a sig called channels and for by Receiving nal pause scan pauses until passing normally busy ZTA the signal disappears timer channels such as repeater scan W YW scans pause for 5 10 or sKIP frequencies Beet 15 sec sean Wie YW Pausing Y NOTE A tone scan function is available to search for subaudible tones e g when you want to find a subaudible tone fre Z quency necessary to open a repeater See p 51 for details E Scan start stop Preparation Scan resume condition p 42 program the scan edges pgs 39 40 program 2 or more memory channels pgs 25 26 set skip settings if desired p 41 Operation Select VFO mode for f
38. 1 E Function display we E Rear Panel ireid aansacasnlevstsagdathcsansaccateusesprastasenseaseadiantatantes E Microphone HM 133V 0 ec ccc cece cece ce see seer eeeeeeeeae 6 E Microphone keypad acl 2 SETTING A FREQUENCY 9 12 MM Preparations iiiaae aT A E alia ore darted let 9 E Using the tuning dial 169 E Using the keypad 10 E Using the A V keys 10 E Tuning step Selection 0 0 eee cece cece cee te eee eeeeeeeeeeeeeneeenanee 11 M Lock fUNCHONS orison EEA N reaa AN AEA NEA NE TNS 3 BASIC OPERATION E Receiving Ara aA une etd niin eh dds E Monitor funtion siriani seca ceca a AeA A E E Audio mute function E Squelch attenuator E S meter squelch sseseesesrserserrersenresrsrnenriornentarisenenrarrsenrurrereenean E Transmitting 15 E Selecting output power 16 E One touch PTT function cee eeeeeeceeeeeeeeeeeeeeeeeeeesenetereeneeeeeeaeeenes 16 REPEATER OPERATION 17 23 E Accessing a repeater ooo eee eeeeeeeeeteeeeesereeeeeeeeeeeeseneeereeeeeaeeeaeeaes 17 W Subaudible tones sesssssseneisisinenersisenrisisinrnrinrnrnrinrnrntnrnnrnrnneen 19 E Offset frequency E Repeater lockout E Reversed duplex mode E Auto fepeaten nicotianae aat i E aa i tod MEMORY OPERATION E General descriptio M sarokra riar aiar e aineena noie e in iet DEEE M Memory channel selection s ssesesssensisisinensisrsrnrnsrnrnensnnrnrnrnnes Programming a memory channel a E Tra
39. 1 Set the desired frequency in VFO mode e Select output power if desired p 15 2 Push BANK OPTION for 1 sec then push BANK OPTION or MR CALL to select the digital select mode e DG appears 3 Push A to turn the digital mode ON 4 Push BANK OPTION to select the your call sign select mode e MYC appears 5 Push A or V to select the desired your call sign channel if you have programmed several call signs E BANK OPTION When sending a CQ Select CQ as the call sign Push BANK J AH twice to select the call sign select mode e YUC appears Rotate DIAL to select the desired channel then push SET or MONI Push S MW IAM for 1 sec to edit CQCQCQ DIGITAL for Select CQ as the call sign Push BANK OPTION twice to select the call sign select mode e YUC appears Push A or V to select the desired channel then push ser B D OFF or ENT C T OFF Push FUNC then ctr A MW for 1 sec to edit CQCQCQ E BANK OPTION When calling the desired station Select the desired call sign Push BANK o A twice to select the call sign select mode e YUC appears Rotate DIAL to select the desired call sign pre pro grammed or set the desired call sign see pgs 59 60 l URAUR 265 z SET MONI N Push any key other than i
40. 128 Push te ia ta ie Ges C C Push 6 then cit momentarily YO BH 3 Yo As HSBS a MONI LOW M CALL V MHz SET MONI Low ae a V MHz SET MONI ea ONE pia w Push then 1 sec Push E and continue to push 1mp J Beep Eo AN E IL HA ea Beep gt LIT CITATA Tee a az pua a pais zap ad a O gt Beep Uad 2A ane am T SCAN Gia ON aqua DuP J T SCAN aw SCAN qu apm T SCAN ae em SET MONI LOW TONE M CALL VIMHZz J SET MONI LOW TONE M CALL V MHz J SET MONI LOW TONE M CALL V MHz 40 7 SCAN OPERATION E Skip channel setting The memory skip function speeds up scanning by checking only those memory channels not set as skip channels Set skip channels as follows The display shows that z u memory channel 15 is HE i NS N I setas a skip channel Select a memory channel Push M CALL Giiile to select memory mode Rotate DIAL to select the desired channel to be a skip channel Push SET KIZA to enter set mode Push SET or MONI several times until CHS appears as shown above Rotate DIAL to turn the skip function ON or OFF for the selected channel xP appears The channel is skipped during scan CHS ON GxrP disappears The channel is scanned during scan CHS OFF Push any key other than SET or MONI to exit set mode USING SET MODE Select a m
41. 5 97 4 114 8 136 5 159 8 173 8 189 9 206 5 233 6 71 9 85 4 100 0 118 8 141 3 162 2 177 3 192 8 210 7 241 8 74 4 88 5 103 5 123 0 146 2 165 5 179 9 196 6 218 1 250 3 77 0 91 5 107 2 127 3 151 4 167 9 183 5 199 5 225 7 254 1 NOTE The transceiver has 50 tone frequencies and con sequently their spacing is narrow compared to units having 38 tones Therefore some tone frequencies may receive interference from adjacent tone frequencies 4 To prevent interference from adjacent tone frequencies Y using the frequencies as in the following table is recom mended e Recommended tone frequencies MMA 67 0 77 0 88 5 100 0 114 8 131 8 151 4 173 8 203 5 233 6 69 3 79 7 91 5 103 5 118 8 136 5 156 7 179 9 210 7 241 8 71 9 82 5 94 8 107 2 123 0 141 3 162 2 186 2 218 1 250 3 74 4 85 4 97 4 110 9 127 3 146 2 167 9 192 8 225 7 Calling a waiting station using pocket beep A subaudible tone matched with the station s CTCSS tone fre quency or 3 digit DTCS code with polarity is necessary Use the tone squelch on the next page or a subaudible tone en coder pgs 19 50 E Tone DTCS squelch operation The tone or DTCS squelch opens only when receiving a sig nal with the same pre programmed subaudible tone or DTCS code respectively Set the op
42. Does not scan the memory channel skips Memory bank setting Sets the desired memory bank A to J and OFF to assign the regular memory channels This item appears when set mode is accessed from memory mode only AH xs PHHH g SET MONI SET MONI Memory bank link function Sets the memory bank link function ON and OFF default The link function provides continuous banks scan that scans all contents in the selected banks during bank scan This item appears when set mode is accessed from memory mode only ILko HL SET MONI SET MONI Bank link setting Rotate DIAL to select the memory bank link function ON Push SET or MONI to select the desired bank to be linked e BLA Bank A BLB Bank B BLC Bank C BLD Bank D BLE Bank E BLF Bank F BLG Bank G BLH Bank H BLI Bank BLJ Bank J Rotate DIAL to select ON to linking the bank Repeat steps and to set the link condition Wide Narrow setting Sets both the transmission and reception passband width from wide and narrow When narrow is set the transmission deviation and reception passband width become half of the wide setting approx This setting can be set for each memory call and VFO inde pendently Y NOTE This item MUST be set W WIDE when operating Z the digital mode Pt ANS l f Pf ANS Nf WNC INN N WAUA ING ON Wide setting default Narrow setting AM FM mode sele
43. GmbH Himmelgeister strake 100 D 40225 D sseldorf Authorized representative name T Maebayashi General Manager ache iv EN 60950 1992 08 A11 1997 Signature Icom Inc mm MODE ARRANGEMENT VFO mode p 9 SET FA fo lt memory encoder is eam i ViMHz V MHz activated 4 BANK D M CALL V MHz TONE A When the DTMF DTMF MEMORY LANM J SCAN MONI Low TONE M CALL V MHz CALL CHANNEL p 35 A anu ean SET MONI Low TONE M CALL V MHz for 1 sec WEATHER CHANNEL p 83 Jeanke MONI 1 5 9 A for 1 sec qs eam am SCAN MONI Low TONE M CALL V MHz lt gt set See p 86 for details qu Le an MONI Low TONE M CALL V MHz Appears when accessing from memory mode only CHANNEL NAME BANK CHANNEL p 32 Available for USA versions only INDICATION p 29 Appears in some version only 1 I I I I I I I I I I 1 I I I I I I I I I I I 1 I I I I I I I I I I i E S 4 Display dimmer p 75 Scan resume timer p 76 AM Ty _TIN LA LUM color p 75 Transmit permission p 76 HAS LHS UF Repeater tone p 75 Skip setting p 77 BAK Memory bank selection p 77 PLH 0F z Bank link func
44. Hz several times to select the GPS automatic transmission e GTX appears Rotate DIAL to set the interval time for the GPS auto matic transmission Interval time is selectable from 0 5 30 sec 1 3 5 10 30 min TA ae IL 1 cn TW AN AA aN Vv MHz Push SET or MONI several times to edit transmit mes sage if desired see page 71 e When TX message channel C1 is programmed GPS transmis sion automatically transmits TX message C1 Push any key other than indicated function keys to exit op tion set mode IMPORTANT GPS Automatic transmission transmits at fe very setting interval even while receiving an another sta ions communication To prevent interfere the another sta A Gt ions set the GPS transmission together with the Repeater A lockout item RLO set to BU busy lockout in initial set Y mode p 84 N N VY Receiving a GPS transmission Push BANK for 1 sec to enter the option set mode Push BANK egal or V MHZz several times to select the received position e RX POS appears Re PIs Push MONI or MONI to enter the position indication Latitude data and longitude date appear alternately Push BANK gaal twice to select the received GPS mes sage Push MONI or SET to enter the message e Received message is indicated push MONI or SET to move the cursor to left or right
45. IAL to set the desired timer e SCT 15 Scan pauses 15 sec while receiving a signal e SCT 10 Scan pauses 10 sec while receiving a signal SCT 5 _ Scan pauses 5 sec while receiving a signal e SCP 2 Scan pauses until the signal disappears and then resumes 2 sec later Push any keys than SET or MONI to exit set mode SCAN OPERATION 7 USING SET MODE Push set B D OFF to enter set mode Push set B D OFF or Ent C T OFF several times until SCT or SCP appears as shown at left Push A or V to select the scan resume condi tion See item at left for scan resume condition details 4 Push ctr A MW to exit set mode o m A N q w NOTE G Set mode cannot be accessed when memory names are Z displayed To set the scan resume condition return to fre GY quency indication by pushing MONI ENIH on the front panel for 1 sec or push FUNC then mon 1 ANM HM 133V to cancel the channel name indication then set as 7 described on this page Qs OOOH 42 PRIORITY WATCH 8 E Priority watch types Priority watch checks for signals on a VFO frequency every 5 sec while operating on a memory channel The transceiver has 3 priority watch types to suit your needs You can transmit on the VFO frequency while the priority watch operates The watch resumes according to the selected scan resume c
46. Inc and the com logo are registered trademarks of Icom Incorporated Japan in the United States the United Kingdom Ger many France Spain Russia and or other countries PRECAUTION Z WARNING RF EXPOSURE This device emits Radio Frequency RF energy Extreme caution should be ob served when operating this device If you have any questions re garding RF exposure and safety standards please refer to the Federal Communications Commission Office of Engineering and Technology s report on Evaluating Compliance with FCC Guide lines for Human Radio frequency Electromagnetic Fields OET Bulletin 65 Z AWARNING NEVER connect the transceiver to an AC outlet This may pose a fire hazard or result in an electric shock Z WARNING NEVER operate the transceiver while dri ving a vehicle Safe driving requires your full attention anything less may result in an accident NEVER connect the transceiver to a power source of more than 16 V DC This will ruin the transceiver NEVER connect the transceiver to a power source using re verse polarity This will ruin the transceiver NEVER cut the DC power cable between the DC plug and fuse holder If an incorrect connection is made after cutting the transceiver may be damaged NEVER expose the transceiver to rain snow or any liquids The transceiver may be damaged NEVER operate or touch the transceiver with wet hands This may result in an electric shock or ruin the transceiver
47. K SET MONI Time out timer To prevent accidental prolonged transmission etc the trans ceiver has a time out timer This function cuts a transmission OFF after 1 30 min of continuous transmission This timer can be cancelled TOT OF The time out timer is turned OFF default e TOT 1 30 The transmission is cut OFF after the set period elapses OTHER FUNCTIONS 13 Auto repeater U S A version only The auto repeater function automatically turns ON or OFF the duplex operation with a specified shift direction and tone en coder when the operating frequency falls within or outside of 145 200 145 495 MHz 146 610 146 995 MHz and 147 000 147 395 MHz range The offset and repeater tone frequencies are not changed by the auto repeater function reset these frequencies if necessary OF The auto repeater function is turned OFF R1 Activates for duplex only default e R2 Activates for duplex and tone 13 OTHER FUNCTIONS Auto power OFF The transceiver can be set to automatically turn OFF after a specified period with a beep when no key operations are per formed 30 min 1 hour 2 hours and OFF default can be specified The specified period is retained even when the transceiver is turned OFF by the auto power OFF function To cancel the function select OF in this set mode Repeater lockout Selects lockout type from repeater busy and OFF OF No lockout
48. KEY L to deactivate the p 12 e Priority watch is paused on the watching fre microphone keypad lock function quency e Push M CALL ile to cancel the watch p 44 MAINTENANCE 15 PROBLEM POSSIBLE CAUSE SOLUTION REF Some memory channels The input channel number has not yet been pro e Rotate DIAL to check whether the channel has cannot be selected via the grammed been programmed or not microphone keypad Scan does not operate e The squelch is open Set the squelch to the threshold point p 13 e Only 1 memory channel is programmed or other e Program other memory channels or cancel the pgs 25 channels are set as skip channels memory skip function in the desired channels 26 41 e Priority watch is activated Cancel the watch p 44 erroneous information Transmission is automati Time out timer is activated e Set the timer to OFF p 80 cally cut off Transmission continues One touch PTT function is activated e Turn the function OFF p 16 even when the PTT is re leased The function display shows The CPU is malfunctioning e Reset the CPU p 85 E Fuse replacement If the fuse blows or the transceiver stops functioning find the source of the problem if possible and replace the damaged fuse with a new rated one FGB 20 A as shown at right 15 MAINTENANCE E Optional unit installation Remove DIAL and unscrew the
49. MONI or SET to set into code programming condi tion e The 1st digit blinks and CO indication stops blinking Rotate DIAL to set the desired code Push MONI or SET to select 2nd digit then rotate DIAL to set the desired code 2nd digit blinks 1st digit stop blinking e Repeat this step for 3rd digit programming 1 4 1 s 2 t gt L T _ LU os V MHz ry l A Lit SET MONI Push MONI or SET to program the ID code e Long beep sounds and the CO indication blinks Rotate DIAL to select a transmit code channel from C1 to C6 Repeat steps to to set transmit code channel Push S MW Qj to set the channel for receive inhibit or receive accept e When receive inhibit is set SKIP appears as follows e Code channel CO cannot be set as receive inhibit e See p 54 for receive accept and receive inhibit details an SET MONI V MHz J Appears when receive inhibit is set to the code channel Push any key other than indicated function keys to exit code set mode N Push BANK OPTION for 1 sec then push A or V to turn Pager mode ON Push ser B D OFF to enter to the code set mode One of either CP or CO to C6 blinks e CO is the ID code and C1 to C6 are the transmit
50. NG SET MODE When the reversed duplex mode is selected the receive fre quency shifts Transmit frequency shifts in normal duplex mode Each receive and transmit frequency is shown in the table below with the following conditions R m 4 Input frequency 145 30 MHz Direction negative Offset frequency 0 6 MHz Reversed OFF ON Rx frequency 145 30 MHz 144 70 MHz Tx frequency 144 70 MHz 145 30 MHz Push SET IKAN to enter set mode Push SET or MONI several times until the REV dis play appears as shown below Rotate DIAL to turn the reversed duplex mode ON or OFF Push any key other than SET or MONI to exit set mode N w REPEATER OPERATION 4 Push set B D OFF to enter set mode Push set B D OFF or Ent C T OFF until REV appears Push A or V to set the reversed duplex mode ON and OFF Push c_r A MW to exit set mode 22 4 REPEATER OPERATION Auto repeater U S A version only The USA version automatically activate the repeater settings DUP or DUP and tone encoder ON OFF when the operating frequency falls within the general repeater output frequency range and deactivate them when outside of the range Setting the auto repeater function ON OFF Push PWR to turn power OFF While pushing SET KIA turn power ON to enter initial set mode
51. O o 010 INSTRUCTION MANUAL VHF TRANSCEIVER IC gt 2200H eg fe g U lt BANK ap Icom Inc FOREWORD IMPORTANT Thank you for purchasing this Icom product The IC 2200H VHF TRANSCEIVER is designed and built with Icom s superior technology and craftsmanship With proper care this product should provide you with years of trouble free operation We want to take a couple of moments of your time to thank you for making your IC 2200H your radio of choice and hope you agree with Icom s philosophy of technology first Many hours of research and development went into the design of your IC 2200H FEATURES O 65 W of high transmit output power except Korea Taiwan versions O Tone squelch DTCS squelch standard O Dual color amber amp green LCD backlight O Remote control microphone available optional for some versions O Optional Digital modulator demodulator O Optional DTMF decoder READ ALL INSTRUCTIONS carefully and completely before using the transceiver SAVE THIS INSTRUCTION MANUAL This in struction manual contains important operating instructions for the IC 2200H EXPLICIT DEFINITIONS WORD DEFINITION P linj i i A WARNING ersonal injury fire hazard or electric shock may occur CAUTION Equipment damage may occur Recommended for optimum use No risk of NOTE ae personal injury fire or electric shock Icom Icom
52. OFF to set into call sign programming mode e The 1st digit blinks and channel indication stops blinking Push A or V to set the desired charac ter or code e Push set B D OFF or Ent C T OFF to move the cursor to left or right respectively 5 Push set B D OFF or Ent C T OFF to select 2nd digit then push A or V to set the desired character or code e 2nd digit blinks 1st digit stops blinking e Repeat this step for programming your call sign 6 Push ctr A MW to fix the call sign and exit programming condition ow gt Z A Cg v pn O Zz N w gt N Y NOTE The digital repeater for an amateur radio operation is Z not available at present of December 2003 It will be de 7 signed in the future S 12 DIGITAL MODE OPERATION E Digital voice mode operation Set the desired frequency in VFO mode pgs 9 10 e Select output power if desired p 15 Push BANK JA for 1 sec then push BANK A or V MHz several times to select the digital select mode DG appears 3 Rotate DIAL to turn the digital mode ON Appears fot a IT Push BANK 0i to select the your call sign select mode e MYC appears Rotate DIAL to select the desired your call sign channel if you have programmed several call signs mat Th x T TN Zi NIN TI 2 Ath D HN D D L V MHz
53. ON E Function display Peta pL E ANT FANT FAN o EE 0D 0 o DIGITAL PRIO AO BUS ofnar A INA INA IA INA Mt JANI JAN ny e ntl T Me ANM J DUP a ean aah SET MONI LOW _ TONE M CALL___V MHz FREQUENCY READOUT Shows the operating frequency channel names set mode contents etc e Frequency decimal point flashes while scanning p 38 d appears in place of the 1st digit while the DTMF memory function is in use p 45 TRANSMIT INDICATOR Appears while transmitting p 15 Flashes while transmitting with the one touch PTT func tion p 16 AUDIO MUTE INDICATOR p 14 Appears when the audio mute function is activated via mi crophone control Q NARROW MODE INDICATOR p 78 Appears when the narrow mode is selected Narrow mode is not available with some versions OUTPUT POWER INDICATORS p 16 LOW appears when low output power MID and LOW appear when mid low output power MID appears when middle output power is selected e Mid low power is not available with some versions KEY INDICATORS Indicate the function s of the front panel keys directly below the function display Q SKIP INDICATOR p 41 Appears when the selected memory channel is specified as a skip channel MEMORY CHANNEL NUMBER INDICATORS Shows the selected memory channel number p 24 C appears when the call chann
54. SET KIA to enter set mode Push SET or MONI until and offset frequency appear DA Se IIa 3 Rotate DIAL to set the desired offset frequency e Push V MHz to select the 1 MHz tuning steps Push any key other than indicated function keys to exit set mode Push set B D OFF to enter set mode Push set B D OFF or Ent C T OFF until 8 and offset frequency appear n m 4 N 2000 D OFF 200S Push COON w Push A or V to set the desired offset e Direct frequency entry from the keypad is not possi ble Push cir A MW to exit set mode E Repeater lockout USING INITIAL SET MODE This function helps prevent interference to other stations by inhibiting your transmission when a signal is received The transceiver has two inhibiting conditions repeater and busy Push PWR to turn power OFF While pushing SET exeh4 turn power ON to enter ini tial set mode PWR SET M00 Push SET or MONI several times until the RLO dis play appears as shown below Rotate DIAL to turn the repeater lockout function to RP BU or OFF RP Transmit is inhibited when a signal with un matched sub audible tone is received e BU Transmit is inhibited when a signal is received Push PWR to exit initial set mode E Reversed duplex mode USI
55. T IKIN to enter set mode Push SET or MONI several times until Ct for tone squelch or dt for DTCS squelch appears SET SET MONI DTCS code setting Tone squelch frequency setting Rotate DIAL to select the desired tone squelch frequency or DTCS code When operating the pocket beep function with DTCS squelch push SET once then rotate DIAL to select the DTCS polarity DTCS polarity setting Push any key other than SET or MONI to exit set mode Push TONE IEAA several times until ups or m are displayed to turn ON the pocket beep with tone squelch or DTCS squelch respectively O O f po Y oopo0pmwmooo0 E r E ET lt a d aus w coa EW aus w SET MONI M CALL V MHz SET MONI Appears when the pocket beep with tone squelch is activated Appears when the pocket beep with DTCS squelch is activated 8 When a signal with the matched tone is received the transceiver emits beep tones and blinks m Beep tones sound for 30 sec and n blinks To stop the beeps and blinking manually push any key When the beep tones are not stopped manually m continues flashing until step is operated Push PTT to answer It disappears and cancels the pocket beep function automati cally Push TONE A several times until pp or dis appears to cancel the ton
56. V to select the desired bank to be set Push cir A MW to set the channel into the bank and exit set mode Repeat steps 1 to 5 to set an another memory channel into the same or another bank E Transferring bank contents Contents of programmed memory banks can be cleared or transferred to another bank Y INFORMATION Even if the memory bank contents are Z cleared the memory channel contents still remain pro GZ grammed Select the desired bank contents to be transferred or erased Push M CALL iiile to select memory mode Push BANK g4g then rotate DIAL to select the de sired memory bank e Bank initial blinks Push BANK egg to select the bank then rotate DIAL to select the desired contents e Bank initial stops blinking Push SET Heel enter the set mode Push SET or MONI several times until BAK appears e Bank initial appears bad fe TT wS L ar Rotate DIAL to select the desired bank initial to transfer or erase e Select indication when erasing the contents from the bank Push any key other than SET or MONI to transfer or erase and return to regular memory condition MEMORY OPERATION 5 Repeat steps to for transferring or erasing an an other banks contents f L Select the desired bank contents to be trans BANK ferred or erased 7 Push MR CALL to select memory mode
57. a dodanie E Code squelch pisitari iranieni apada lena 12 DIGITAL MODE OPERATION Required Optional UT 115 E Digital mode operation E Call sign programming E Digital voice mode operation E When receiving a Digital call E Break in communication E Emergency communication cc cece e eee eeeeeeeeeeeaee E Digital code Call sign squelch operation 0 eee E Slow data communication oy E Other setting items ee cee eee see eeeeeeneaneanenseaeenaaae MM GPS operation ei eoe a ari aR y T dines a Aia 13 OTHER FUNCTIONS ME Seb modei A Ge Le RE ION AC E A E Initial S tMOde ana R AR Geos E Weather channel operation 83 E Microphone keys E Partial reset MAI TOS6t e norena need enced wives EE SAE SEAS E Data cloning as 14 SPECIFICATIONS essseessecseeseeesenenseeseneeeeseeeseeeseeseeeseneneneneeeneess 15 MAINTENANCE jciescccnecenweccrsdececevecceevecsccecenteadsatescenvercoceecevtdedes E Troubleshooting E Fuse replacement E Optional unit installation 00 0 0 eee eee 91 16CE 17 MODE ARRANGEMENT sccsscceeesseeseeseseeseeeneeesenseeeseeneeeees 93 94 N A N MM QUICK REFERENCE GUIDE E Installation Location Select a location which can support the weight of the trans ceiver and does not interfere with driving in any way We rec ommend the locations shown in the diagram below NEVER place
58. acket 2 20 1 HM T18N HAND MICROPHONE Mounting screws nuts and washers 1 set HM 133V REMOTE CONTROL MICROPHONE Microphone hanger 00 ccc eee eee eee 1 SP 10 Insulation sheet eseti nesa ee eee ee 1 EXTERNAL SPEAKER HM 118TN DTMF MICROPHONE supplied versions are also available OPC 440 OPC 647 mic EXTENSION CABLES tDepending on version OPC 441 SPEAKER EXTENSION CABLE Used for optional unit installation see p 91 for details OPC 1132 OPC 347 Dc POWER CABLES OPC 589 ADAPTER CABLE CS 2200H CLONING SOFTWARE OPC 478 OPC 478U CLONING CABLE OPC 474 CLONING CABLE a TETT j eee TITT cis Ed TABLE OF CONTENTS FOREWORD IMPORTANT onosaia EXPLICIT DEFINITIONS sixes ceccpecesepuiceasizetessecsusvccevoteueaccciisesinvactecpuaes i PRECAUTION issccetasscitvecuepecinevasossarseasaespepteesatevipsixdrsasvanwesavesedsttenyes ii SUPPLIED ACCESSORIES AND OPTIONS iij TABLE OF GONTENTS aet ianed en eaaa aaea at aaiae l aaie i QUICK REFERENCE GUIDE cccccssscsssseseeseeseeseeseeseeseesoeeneans E Installation l Your fifSt contact mann o a a AA IV E Repeater operation s eesesroeseeisrsessererrsrnrnrerirtnrnrrsesrararesenrnrese V E Programming memory 1 PANEL DESCRIPTION ccccssssssssssesseesssssesseseseesenseseeenseneenenanee 1 8 E Erontpanelk iatna denrea AEN Eat LETIA ENESE EAEE
59. annel e Programmed memory channels only can be se lected ge ea M CALL V MHz MEMORY OPERATION Using the A V keys 1 Push MR CALL to select memory mode MR CALL 2 Push A or V to select and set the desired memory channel e Pushing AJ V for 1 sec activates a scan e If scan is activated push A V again or push ctr A MW to stop it CA av Using the keypad f_ 1 Push MR CALL to select memory mode MR CALL 2 Push ent C T OFF to activate the keypad for numeral input Cw 3 Push 3 appropriate digit keys to input a chan nel number When inputting non programmed channel num bers the previous memory channel appears e Push only 1 appropriate digit key Moni 1 ANM scan 2 T SCAN or PRIo 3 PTT M then push TONE 1 or saLv 16KEY L to select scan edge channels and can be used for A and b respectively J 5 24 5 MEMORY OPERATION E Programming a memory channel VFO settings including the set mode contents such as sub audible tone frequency etc can be programmed into a mem ory channel Set the desired frequency in VFO mode Push V MHzE eZ X to select VFO mode Set the frequency using DIAL Set other data e g tone frequency duplex information etc if required Push S MW RA momentarily M indicator and the
60. any other keys than indicated function keys to exit code set mode e 100 MHz digit shows C TATA ae LHA MAI ro eC am M CALL V MHz Operate the transceiver in the normal way push PTT to transmit release PTT to receive To cancel the code squelch push BANK 0i for 1 sec then rotate DIAL 100 MHz digit shows 1 when the function is cancelled E o BANK OPTION 2 1 Set the operating frequency Push BANK OPTION for 1 sec then push A V to select code squelch mode e CS appears Select the desired transmit code channel Push SET or MONI Push AJ V Push ctr A MW to return to previous condition Communicate with the other party as nor mal push PTT to transmit release to re ceive To cancel the code squelch push BANK OPTION for 1 sec then rotate DIAL Required Optional UT 115 E Digital mode operation The IC 2200H with optional digital unit UT 115 can be oper ated for digital voice mode and slow data operation for both transmit and receive Also available for connecting GPS re ceiver compatible with an RS 232C output NMEA for mat 4800 bps and transmit receive position data Y NOTE Digital mode operation MUST be set AM FM mode g selection to FM and Wide Narrow setting to Wide in set Y mode pgs 74 78 MQ E Call sign programming 4 kind of call sign memo
61. c to return to frequency indi cation if desired MPORTANT Once channel name indication mode is Z selected always access the channel name programming A condition when SET KA is pushed G When set mode accessing is necessary cancel the chan Z nel name indication by pushing MONIEN for 1 sec G then access to set mode EXAMPLE Programming CLUB into memory channel 1 Select memory channel 15 Rotate Or select the Push 2 ser or 4 uon Push any other keys than then push for 1 sec eharacton to move the cursor Banas CE ser or 2 wom epea vw vt 25 Sp previous T g E Ga USE Ug g A in Yo SET 24 on Re eyesore as ee ea mo cm m OUOU Tem EIES E MEMORY OPERATION 5 crophone 0 Channel names can also be programmed via the mi 1 Select the memory call channel to be assigned memory 5 Push set B D OFF or Ent C T OFF to move the cur names sor to left or right respectively Push MR CALL to select memory mode then select 6 Repeat steps 4 and 5 until the desired channel names the desired memory channel via A V or keypad are displayed Scan edge channels can also be selected 7 Push cLR A MW to program the name and exit the Push MR CALL for 1 sec to select the call channel channel name programming condition 2 Push FUNC then mont 1 ANM m
62. call gt VFO Select the memory call channel to be transferred Push M CALLGGile to select memory mode then ro tate DIAL to select the desired memory channel Push M CALLGqile for 1 sec to select the call chan nel Push S MW g for 1 sec to transfer the selected mem ory call channel contents to the VFO e VFO mode is selected automatically A 5 gt Z a Ko gt 4 Select the memory call channel to be transferred Push MR CALL to select memory mode then select the desired memory channel via A V or keypad Push MR CALL for 1 sec to select the call channel Push FUNC then ctr A MW for 1 sec to transfer the selected memory call channel contents to the VFO e VFO mode is selected automatically Front panel operation Push 4 2 to select memory mode EXAMPLE Transferring memory channel 30 contents to VFO f a r Rotate for setting memory channel LOCK SET MONI LOW M CALL V MHz SET MONI TSCA co ex LOCK amp om MB ABD 46 16 OVU HM 133V operation Push wi to select memory mode Select memory channel S MW OD Push _ for 1 sec Push une then push for 1 sec 27 MEMORY OPERATION 5 Select the memory call channel to be trans ferred Push MR CALL to select memory mode then select the desired memory channel via A V or keypad Push MR CALL for 1 sec
63. cation blinks DTMF MEMORY ENCODER Push SET or MONI e The first digit blinks Rotate DIAL to select the desired code Push MONI to select the next digit e Push SET to move the cursor backward Repeat the steps and to set the desired DTMF tone sequence e The S RF indicator shows the digit group The indication in creases every 6 digit Push V MHz then push any key other than indicated function keys to exit DTMF memory programming condi tion Push eae for 1 sec EXAMPLE Programming 5428AB453 into DTMF memory channel d4 Push LE ser or C uon INe zx T NAS 21 LIE F ee o V MHz SET MONI Rotate to turn the DTMF encoder ON N M TIT WAS S T l pow 1 SET MONI vmi J Repeat the previous step until the desired code is entered Push 2 vam then any other keys than indicated function keys E Transmitting a DTMF code Automatic transmission DTMF memory 1 GaN DTMF Push FUNC then Low 6 DTMF to turn the DTMF memory encoder ON d appears in place of the 100 MHz digit Push BANK OPTION for 1 sec then ser B D OFF to enter the DTMF memory pro gramming condition Push A or V to select the desired channel Push PTT to transmit the selected memory e Exit the programming condition automatically Each pus
64. ck function ON and OFF SETTING A FREQUENCY 2 Microphone keypad lock This function locks the microphone keypad Push FUNC then sacv 16KEY L to switch the microphone keypad lock function ON and OFF e Lights orange while the microphone keypad lock function is activated PTT VFO LOCK MR CALL BANK OP TION 4 V F 1 F 2 DTMF S and FUNC on the microphone can be used All keys on the transceiver can be used e The keypad lock function is released when the power is turned OFF then ON again 16KEY L 12 3 BASIC OPERATION E Receiving Push PWR for 1 sec to turn power ON Set the audio level Push MONIEN to open the squelch Rotate the VOL control to adjust the audio output level Push MONIEN again to close the squelch 3 Set the squelch level Rotate SQL fully counterclockwise in advance Rotate SQL clockwise until the noise just disappears When interference is received rotate SQL clockwise again for attenuator operation p 14 Set the operating frequency pgs 9 10 When receiving a signal on the set frequency squelch opens and the transceiver emits audio Appears when receiving a signal BUSY appears and the S RF indicator shows the relative signal strength for the re LIC CIA annutill A i fy Hwi ceived signal iah as com SET MONI Low a M CALL V MHz CONVENIENT f_ The squelch level can al
65. clearing the memory contents a partial resetting function is available for the transceiver Turn power OFF if transceiver is powered ON While pushing V MHzE eZij turn the power ON to par tially reset the transceiver asap D a Ga am SET MONI Low TONE M CALL V MHz PWR V L a AT POWER ON E All reset The function display may occasionally display erroneous in formation e g when first applying power This may be caused externally by static electricity or by other factors AT POWER ON If this problem occurs turn power OFF After waiting a few seconds turn power ON again If the problem persists per form the following procedure e Partial resetting is also available See left for details Y MPORTANT A Resetting the transceiver CLEARS all memory information Z and initializes all values in the transceiver While pushing SET IKA and S MW Ig turn the power ON to reset the CPU S W fii PWR o I JLICIC E Data cloning Cloning allows you to quickly and easily transfer the pro grammed contents from one transceiver to another or data from a personal computer to a transceiver using the optional CS 2200H CLONING SOFTWARE Cloning between transceivers Connect the OPC 474 cloning cable to the SP jack of the master and sub transceivers The master transceiver is used to send data to the sub trans ceiver OTHER FUNCTIONS 13
66. code Push A or V to select the desired code channel Enter the desired 3 digit code via the key pad Push set B D OFF to set the channel for receive inhibit or receive accept e When receive inhibit is set SKIP appears Code channel CO cannot be set as receive in hibit e See right above for receive accept and re ceive inhibit details Repeat steps 3 to 5 to set additional code channels if desired Push ctr A MW to exit code set mode PAGER CODE SQUELCH 11 e Receive accept receive inhibit Receive accept SKIP indicator does not appear ac cepts pager calls when the transceiver receives a signal with a code the same as that in the code channel Receive inhibit SKIP indicator appears rejects calls even when the transceiver receives a code the same as that in the code channel Transmit codes should therefore be programmed for receive inhibit otherwise the trans ceiver will not reject unnecessary calls e Pager code squelch operation during channel indication To use these functions in channel indication the pager code squelch setting must be programmed with other memory con tents before selecting channel number indication 11 PAGER CODE SQUELCH E Pager operation Calling a specific station Program the desired code channel in advance p 53 Set the operating frequency Set the VOL a
67. code These codes are 3 digit DTMF codes and must be written into the code channels before operation Decide the ID code of each transceiver and a group code for your group Decide whether you want to return to normal operation or code squelch operation after a connection is made Q Program the ID code group code and transmit codes other station s codes as below Code channel assignment IDOR CODE CHANNEL RECEIVE ACCEPT OR GROUP CODE NUMBER RECEIVE INHIBIT Your ID code 0 Receive accept only Other parties 1 6 Receive inhibit should be ID code S programmed in each channel Receive accept must be Group code One of 1 6 programmed Memory space P Receive inhibit only Channel CP automatically memorizes an ID code when receiving a pager call The contents in channel CP cannot be changed manually 11 PAGER CODE SQUELCH Code programming An ID code MUST be programmed into code channel CO Up to 6 transmit codes are programmable into code channels C1 to C6 if required Push BANK Gag for 1 sec then rotate DIAL to turn Pager mode ON e PG appears Push SET or MONI One of either CP or CO to C6 flashes e CO is the ID code and C1 to C6 are transmit codes 3 Rotate DIAL to select code channel Co A different ID code must be programmed into each transceiver Push
68. ction Sets the operating mode for receiving from AM or FM mode default Y NOTE This item MUST be set FM when operating the Z digital mode APSE A RAM SET MONI SET MONI FM mode selection default AM mode selection OTHER FUNCTIONS 13 Weather alert function U S A versions only Turns weather alert function ON and OFF Weather alert OFF default Weather alert ON 13 OTHER FUNCTIONS E Initial set mode at POWER ON The initial set mode is accessed at power ON and al Entering initial set mode lows you to set seldom changed settings In this way While pushing SET IKA push PWR for 1 sec to you can customize transceiver operations to suit your enter initial set mode preference and operating style Push SET or MONI to select the desired item Rotate DIAL to select the condition or value initial setanode Heme Push PWR to exit initial set mode e Time out timer e Auto repeater e Auto power OFF TOT OF E iJi LU lt Le e Key touch beep gt gt Push 4 ser front panel or microphone gt Push 4 uon front panel or microphone i Available in USA version only e Squelch attenuator Hy TT TIN ii LUN Display type DTMF speed 79 Key touch beep The key touch beep can be turned OFF for silent operation default ON inf a vr IN HE
69. e HBS a CILA MONI Rotate DIAL to select and set the desired subaudible fre quency Push any key other than SET or MONI to exit set mode GY NOTE The subaudible tone encoder frequency can be set Z in a memory call channel temporarily However the set fre ZY quency is cleared once another memory channel or VFO mode is selected To store the tone frequency permanently Z overwrite the channel information D Set the mode channel you wish to set the sub audible tones to such as VFO mode or mem ory call channel e The subaudible tone frequency is independently pro grammed into each mode or channel 2 Push ser B D OFF to enter set mode 3 Push ser B D OFF or Ent C T OFF several n m 4 lt times until s and rt appears or until tw and Ct appears for tone squelch or pocket beep use e When dg is displayed in place of the 100 MHz digit cancel the DTMF memory encoder in advance p 46 SET MONI 4 Push A or W to select and set the desired subaudible tone frequency e Push and hold 4 to change the above tones continuously Push cir A MW to exit set mode oa e Subaudible tone frequency list unit Hz 67 0 79 7 94 8 110 9 131 8 156 7 171 3 186 2 203 5 229 1 69 3 82 5 97 4 114 8 136 5 159 8 173 8 189 9 206 5
70. e pocket beep function CSQL or DSQL is in use p 67 DUPLEX INDICATORS p 17 appears when plus duplex duplex operation is selected oy appears when minus ol 1 PANEL DESCRIPTION E Rear panel SPEAKER JACK SP Accepts an 8 Q speaker Audio output power is more than 2 4 W DATA JACK DATA Connects to a PC or GPS receiver via an RS 232C cable D sub 9 pin for data communication in the RS 232C for mat RS 232C DB 9 female to DATA jack z i TxD GND ic i I EOR E Eo 7 TE o000 RxD 2 5 d mm 9 6 Pin 2 RxD Pin 3 TxD Pin 5 GND POWER RECEPTACLE DC13 8V Accepts 13 8 V DC 15 with the supplied DC power cable 51 Y NOTE DO NOT use a cigarette lighter socket as a G power source when operating in a vehicle The plug g may cause voltage drops and ignition noise may be su perimposed onto transmit or receive audio ANTENNA CONNECTOR ANT Connects a 50 Q antenna with a PL 259 connector and a 50 Q coaxial cable Make sure the connection between transceiver and PC oth erwise misreading may occur for data communication E Microphone HM 133V 0 Cake ss a an 2E Jae JOES SU Mic element fe ICOM HM 133V A different microphone may be supplied de pending on version QVFO LOCK KEY VFO LOCK Push to select VFO mode p 9 Push for 1 sec to switch the lock function ON and OFF
71. e squelch or DTCS squelch func tion 10 POCKET BEEP AND TONE SQUELCH Waiting for a call from a specific station continued fo TSQL ae DTCS AZ 1 2 Set the operating frequency Program the CTCSS tone frequency or DTCS code in set mode Push ser B D OFF to enter set mode Push set B D OFF or Ent C T OFF several times until Ct for tone squelch or dt for DTCS squelch appears Dn blinks when tone squelch Ct or blinks when DTCS squelch dt is selected Push A V to select the desired tone frequency or DTCS code Push set B D OFF to select DTP then push AJ V to select the DTCS polarity Push ctr A MW to exit set mode Push FUNC then push pup 8 TSQL or mip 5 DTCS to turn ON the pocket beep with tone squelch or DTCS squelch re spectively When a signal with the matched tone is re ceived the transceiver emits beep tones for 30 sec and blinks m Push PTT to answer or push ctr A MW to stop the beeps and flashing tn disappears and cancels the pocket beep func tion automatically To cancel the tone squelch or DTCS squelch function push FUNC then Ent C T OFF mn or disappears Available tone frequency list 67 0 79 7 94 8 110 9 131 8 156 7 171 3 186 2 203 5 229 1 69 3 82
72. el is selected p 35 MEMORY INDICATOR p 24 Appears when memory mode is selected S RF INDICATORS Shows the relative signal strength while receiving sig nals p 13 Shows the output power level while transmitting p 16 BUSY INDICATOR p 13 Appears when a signal is being received or the squelch is open Flashes while the monitor function is activated AUTO POWER OFF INDICATOR p 81 Appears while the auto power off function is in use PRIORITY WATCH INDICATOR p 44 Appears while the priority watch is activated blinks while the watch is paused PANEL DESCRIPTION 1 DIGITAL INDICATOR p 61 Appears when digital mode is selected LOCK INDICATOR p 12 Appears when the lock function is activated TONE INDICATORS appears while the subaudible tone encoder is in use p 17 m appears while the tone CTCSS squelch function is in use p 48 appears while the tone DTCS squelch function is in use p 48 in appears with the fm or indicator while the pocket beep function CTCSS or DTCS is in use p 48 O While in the digital mode operation with the installing an optional Digital unit UT 115 mm appears while the digital code CSQL squelch func tion is in use p 67 appears while the call sign DSQL squelch function is in use p 67 m appears with the pm or indicator while th
73. elect plus duplex Push con cee ees Lif H J 4 ice HH TOW Kl g ANM J Dup T SCAN am SET MONI LOW TONE M CALL V MHz Push hip 8 ee Lif H J A a o OWE Li qs a T SCAN co ean SET MONI LOW TONE M CALL V MHz Push FUNC then pup 7 TONE to turn ON the subaudible tone encoder according to re peater requirements e Refer to p 19 for the tone frequency setting When the repeater requires a different tone system see p 20 A Push and hold PTT to transmit oa Release PTT to receive for Push mont 1 ANM to check whether the other station s transmit signal can be received directly 9 J e N o REPEATER OPERATION 4 Push simp 9 TSQL to return to simplex oper ation e or indicator disappears To turn OFF the subaudible tone encoder push FUNC then ent C T OFF 4 REPEATER OPERATION E Subaudible tones Encoder function Subaudible tones Select the mode channel you wish to set the subaudible tones to such as VFO mode or memory call channel Push SET KIA to enter set mode Push SET or MONI several times until and rt ap pears or until m and Ct appears for tone squelch or pocket beep use When d is displayed in place of the 100 MHz digit cancel the DTMF memory encoder in advance p 46 USING SET MODE d
74. elected tone condition or type in step No indication Cannot be used for operation p CTCSS tone encoder Do CTCSS tone encoder decoder e DTCS tone encoder decoder Push V MHz eM to stop the scan 1 Set the channel to be checked for a tone fre T SCAN quency 2 Selects the tone condition or type to be scanned e Push FUNC then push pup 7 TONE for re peater tone simp 9 TSQL for tone squelch HiGH 4 DTCS for DTCS squelch 3 Push FUNC then scan 2 T SCAN to start the tone scan 4 When the tone frequency is matched the squelch opens and the tone frequency is pro grammed into the selected mode such as memory or call channel 5 Push cLr A MW to stop the scan Required Optional UT 108 E Pager function This function uses DTMF codes for paging and can be used as a message pager to inform you of a caller s identification even when you leave the transceiver temporarily unattended Pager selective code push PTT CoA ea _ Do 2000000 CoA Set both transceivers to either code squelch or non coded operation w Communication C NAN ae gt bs Q i S PAGER CODE SQUELCH 11 E Code programming Before programming The pager and code squelch functions require ID codes and a group
75. emory channel E Select memory mode by pushing MR CALL B Push A or V to select the desired channel to be a skip channel 2 Push ser B D OFF to enter set mode 3 Push set B D OFF or ent C T OFF several times until CHS appears as shown at left 4 Push A or V to set or cancel the skip setting See item at left for skip indicator details 5 Push ctr A MW to exit set mode L n 4 Y NOTES Y NOTES Z Even though scan edge channels cannot be set as skip ZZ channels they ARE skipped during memory scan Z SET mode cannot be accessed when memory names are Z displayed To set the scan resume condition return to fre ZY quency indication by pushing MONIEN on the front G panel for 1 sec or push FUNC then moni 1 ANM HM Y 133V to cancel the channel name indication then set as described on this page E Scan resume condition The scan resume condition can be selected as timer or pause scan The selected resume condition is also used for priority watch p 44 Raptr x The display shows that VP Tazz E the scan will resume AL ivv 15 sec after it stops F IE Push SET IKIN to enter set mode Push SET or MONI several times until SCT or SCP appears as shown above e When d is displayed in place of the 100 MHz digit cancel the DTMF memory encoder in advance p 46 Rotate D
76. erating frequency Program the CTCSS tone frequency or DTCS code in set mode e See p 48 for programming details Push TONE IEAA several times until fn or ap pears in the function display tn for tone squelch for DTCS squelch operation When a signal with the matched tone is received the squelch opens and the signal can be heard e When the received signal includes an unmatched tone the squelch does not open However the S RF indicator shows the received signal strength To open the squelch manually push MONI LQ Operate the transceiver in the normal way push PTT to transmit release PTT to receive To cancel the tone squelch push TONE BSI sev eral times until or disappears POCKET BEEP AND TONE SQUELCH 10 4 n 8 Da lt Set the operating frequency Program the CTCSS tone frequency or DTCS code in set mode e See p 49 for programming details Push FUNC then simp 9 TSQL or HiGH 4 DTCS to turn the tone squelch or DTCS squelch ON When a signal with the matched tone is received the squelch opens and the signal can be heard e When the received signal includes an unmatched tone the squelch does not open However the S RF indicator shows the received signal strength To open the squelch manually push moni 1 ANM Operate the transceiver in the normal way push PTT to t
77. es an unmatched digital code or call sign the squelch does not open However the S RF indicator shows the received signal strength e To open the squelch manually push saL V 16KEY L several times until less than squelch level 7 asa D EB Em SCAN SET MONI Low TONE M CALL V MHz 5 Operate the transceiver in the normal way push PTT to transmit release PTT to receive 6 To cancel the digital code or call sign squelch push FUNC then Ent C T OFF Dn or disappears V While scanning in digital mode e The call sign squelch function deactivate then after can celling the scan it will activate again e Scan stops near channel in a 5 kHz tuning steps and then no sound comes out E Slow data communication In addition to the digital voice communication a slow data communication is available Refer p 5 about the transceiver PC connection details Set the desired frequency Set another settings such as repeater call digital code squelch transmit output power Push BANK ea for 1 sec then push BANK A or V MHz several times to select the automatic data trans mission setting see p 69 e ATX appears e Skip this setting if you want to transmit manually _ a mir HT eet OO AT eI v MHz V MHz i iN u A lg Push BANK Ggg once to select the data communica tion speed setting
78. etails Push and hold PTT to transmit EE appears e The S RF indicator shows the output power selection e A one touch PTT function is available See p 16 for details Speak into the microphone using your normal voice level DO NOT hold the microphone too close to your mouth or speak too loudly This may distort the signal Release PTT to return to receive IMPORTANT for 65 W transmission The IC 2200H is equipped with current detector circuit to protect the power amplifier circuit from high current flowing When a high SWR Standing Wave Ratio antenna or no antenna is connected or when the connected power sup ply s voltage includes the transceiver reduces transmit out put power to 10 20 W approx automatically E Selecting output power The transceiver has 4 output power levels to suit your oper ating requirements Low output powers during short distance communications may reduce the possibility of interference to other stations and will reduce current consumption The Taiwan version has only 3 levels Push LOW PIIA several times to select the output power S RF INDICATOR ane er High court 65 W 50 W 24W Mid cnn 25 W 10 W Mid Low aog O 10 W NA Low gm 5w 5w approx Korea version The output power can be changed while transmitting The microphone can also be used to select output power f_ Push HicH 4 DTCS for high outp
79. frequency can be directly set via numeral keys on the mi crophone 1 Push VFO LOCK to VFO mode if necessary ENT 2 Push ent C T OFF to activate the keypad for c digit input 3 Push 6 keys to input a frequency When a digit is mistakenly input push Ent C T OFF to clear the input then repeat input from the 1st digit e Pushing cLR A MW clears input digits and retrieves the frequency EXAMPLE Setting frequency to 145 3625 MHz Push t ba 3 ma ANM J cD Gi 1 5s 9 T OFF Push ENT C A g eg SET MONI Low TONE M CALL V MHz Push ion fava ues YO FE i H PTT M DTMF D cl 1 Li PRIO3 Low6 gp ap ow C E amp W SET MONI LOW TONE M CALL VIMHZz T SCAN Lf tC l L J Push canz maaac L que gm T SCAN aa SCAN SET MONI LOW TONE M CALL V MHz SETTINGAFREQUENCY 2 E Using the A V keys r Push A or V to select the desired frequency 2 AV e Pushing A V for 1 sec activates a scan If scan starts push A V again or push ctr A MW to cancel it 2 SETTING A FREQUENCY E Tuning step selection Tuning steps are the minimum frequency change increments when you rotate DIAL or push A V on the microphone The following tuning steps are available e 5 kHz e 10 kHz 12 5kHz 15 kHz e 20 kHz e 25 kHz 30 kHz e 50 kHz Y NOTE For convenience select a tuning step that ma
80. gramming condition e The 1st digit blinks and channel indication stops blinking Rotate DIAL to set the desired character Push MONI or SET to select 2nd digit then rotate DIAL to set the desired character 2nd digit blinks 1st digit stop blinking e Repeat this step for programming Push V MHz to set the message Repeat steps to to set another message channels Push any key other than indicated function keys to exit the option set mode Te sco 70 O OIE Rew space tol O O ol oio fn pe fo Ya Go holfole Yo ol olol 0 cole Aa FoTo Jo ES FaRoHa Tol oHe LOMO Nol oHa flo Fee yo To ov Wm Kool Yoo Fo Of 0 Fo E GPS operation The IC 2200H can indicate the current position Latitude and Lon gitude when a GPS receiver compatible with an RS 232C out put NMEA format 4800 bps is connected to DATA jack And also can transmit the position data and message to other stations Position indication While connecting a GPS receiver push BANK A for 1 sec to enter the option set mode Push BANK gagj or V MHz several times to select the GPS setting e GPS appears I TE Sege wy W Rotate DIAL to set the suitable sentence formatter for the connecting GPS receiver e For your position indication is necessary to select GGA or RMC e Sentence
81. h of PTT transmits the DTMF code Push FUNC then set B D OFF to cancel the DTMF memory encoder e When the DTMF encoder is turned ON continuously each push of the PTT transmits the previously se lected DTMF code Transmitting a DTMF memory directly DTMF S Push FUNC then Low 6 DTMF to turn the DTMF memory encoder ON d appears in place of the 100 MHz digit N Push DTMF S to turn the DTMF memory di rect selection ON e The function indicator microphone lights green w Push the desired DTMF channel number 0 to 9 are available for channel numbers The selected DTMF code is automatically transmit ted without pushing PTT DTMF MEMORY ENCODER 9 Transmitting a DTMF memory directly continued DTMF S gt o Z NOTE When no DTMF code programmed chan Z nel number is pushed it transmits previously Y transmitted DTMF memory code Push DTMF S again to deactivate the DTMF memory direct selection Push FUNC then ser B D OFF to cancel the DTMF memory encoder Manual transmission CA DIMF S Deactivate the DTMF memory encoder by LQ pushing FUNC then set B D OFF Push DTMF S to turn the DTMF direct selec tion ON e The function indicator microphone lights green Push one of A to F keys momentarily then push the desired DTMF keys 0 9 and A to F
82. hannel 20 Push _ momentarily then push _ again for 1 sec S MW OD Push 4 32 to select VFO Push _ momentarily Rotate C for selecting memory channel j LiCl C CITA ILSE CA Aa 7 ILIE C TAAas YO AB HSH ea YO Se ag MONI Low M CALL V MHz SET MONI LOW ONE MICALL VIH enra pa ie VvV sS MWwW s Mw OD s MW T Bah eee e TATA Ly ae Beep LG ALA s 9 an gt Beep mm ALA 2G oo ANM oB G23 ED a OF ED EO EW SET MONI Low TONE M CALL Viz J F SET MONI LOW TONE M CALL V MHz 31 E Memory bank selection The IC 2200H has a total of 10 banks A to J Regular mem ory channels 0 to 199 are assigned into the desired bank for easy memory management Push M CALL REA to select memory mode Push BANK A to select memory bank condition e Bank initial blinks DIAL V IE AT he SHV 0 H3 oom T TEI TI nE M CALL va Banke JC JCJICJI BC Rotate DIAL to select the desired bank A to J Banks that have no programmed contents are skipped Push BANK A to set the bank e Initial stops blinking Rotate DIAL to select the contents in the bank No channel numbers are displayed for memory bank operation To return to regular memory condition push BANK 34g twice E BANK OPTION 2 MEMORY OPERATION 5
83. hannels band A1 AA or programmed e P1 stands for 1A 1b scan P1 P2 and P3 in se e P1 to P3 are available when quence Depends on versions they are programmed and A1 FM band 136 1 74 MHz switches with 4 J ee AA AM band 118 136 MHz When AM and FM frequencies are programmed into memory channel disorderly memory scan takes a lot of time very slow Because changing mode takes a time In this case assign AM and FM frequencies into the separate bank respectively And using the bank scan is helpful 7 SCAN OPERATION E Scan edges programming Scan edges can be programmed in the same manner as memory channels Scan edges are programmed into scan edges 1A 1b to 3A 3b in memory channels Set the edge frequency of the desired frequency range in VFO mode Set the frequency using DIAL Set other data e g repeater settings etc if desired Push S MW DM momentarily M indicator and channel number blink Rotate DIAL to select one of scan edge channel 1A 2A or 3A Push S MW DM for 1 sec to program 3 beeps sound and VFO is automatically selected e Scan edge 1b 2b or 3b is automatically selected when continu ing to push S MW RMM after programming To program a frequency for the other pair of scan edges 1b 2b or 3b repeat steps and If the same frequency is programmed into a pair of scan edges programmed scan will not function EXAMPLE Pr
84. he digital mode operation with the installing an optional Digital unit UT 115 PANEL DESCRIPTION 1 KEY FUNCTION SECONDARY FUNCTION gt key OTHER FUNCTIONS Cancels frequency entry p 10 Cancels the scan or priority watch pgs 38 44 Selects a memory channel for program ming p 26 Advances the memory channel number Exit set mode p 74 when continuously pushed after pro gramming is completed p 26 Enters set mode p 74 DTMF memory OFF p 46 Advances the set mode selection order after entering set mode p 74 _____ Sets the keypad for numeral input Turns the subaudible tone encoder pocket Tore p 10 beep or CTCSS DTCS tone squelch OFF S Reverses the set mode selection order pgs 18 49 50 after entering set mode p 74 Turns the pocket beep or CSQL DSQL OFF p 63 s Adjusts the squelch level increments Mutes the audio p 14 LAD 13 e Mute function is released when any operation saLaD p is performed zonen No primary function Sends a 1750 Hz tone signal for 0 5 sec p 20 16KEY L sav Adjusts the squelch level decrement p 13 lt Locks the digit keys on the keypad includ ing the A to D and keys p 12 e Lights orange while the microphone keypad lock function is activated After pushing ens Transmits the appropriate DTMF code pg
85. memory channel then push CD Select the target channel Push _ for 1 sec i TA TA e TEE me i CC MAA Hh Ae 39 a sa giz Hi AA E ser owt Tow TONE meau Wane mica Viie Ss Sow oe reat Vinz Se Sow Tow Sone McAL Vine HM 133V operation Select the memory channel push une then push E Push une then push for 1 sec 28 5 MEMORY OPERATION E Programming channel names Each memory channel and the call channel can be pro grammed with an alphanumeric channel name for easy recognition and can be indicated independently by channel Names can be a maximum of 6 characters see the table below for available characters Meryl 0 HOE space wi yool Push M CALLGGile to select memory mode Rotate DIAL to select the desired memory channel 3 Push MONIEN for 1 sec to select channel name indi cation mode 1 short and 1 long beep sound Push SET KIX4 to select the channel name program ming condition e Frequency readouts disappear Rotate DIAL to select the desired character The selected character blinks Push SET or MONI to move the cursor to left or right respectively Repeat steps and until the desired channel names are displayed Push any key other than SET or MONI to program the name and exit the channel name programming condition Push MONIN for 1 se
86. memory channel number blink Rotate DIAL to select the memory channel to be pro grammed e Memory channels not yet programmed are blank Push S MW QW for 1 sec to program 3 beeps sound Memory channel number automatically increases when contin uing to push S MW QW after programming V CONVENIENT Memory programming can be performed in versatile ways e g memory channel to the same or different memory chan nel memory channel to the call channel etc EXAMPLE Programming 145 870 MHz into memory channel 20 blank channel via the front panel Push ED ae Rotate for setting frequency etc Push ee momentarily p LIC C CI A _ ILIC CII T LIT C TATA gt a I 1obAY ui I 15H DA Li l to bw g Sion o Weal ime ser Wout Tow TONE MONL Vine er e a D 7 oppooo o a f N Rotate N f cae eee oo am SET MONI Low TONE s nw OD B Dy MICALL ViMHz Push _ for 1 sec and continue to push 11 11E 25 MEMORY OPERATION 5 Programming a memory channel via the microphone f __ The microphone can also be used to program mem MW ory channels 1 Set the desired frequency in VFO mode Push VFO LOCK to select VFO mode Set the frequency using the keypad Set other data e g offset frequency duplex direction sub gt Push FUNC then ctr A MW for 1 sec to program
87. n the auto repeater function is turned ON available for the USA version only steps and are not necessary p 23 n Either or appears ap oD w aw SET MONI LOW TONE i EDEDED Push TONE BSN several times to turn ON the sub audible tone encoder according to repeater requirements A appears 88 5 Hz is set as the default refer to p 19 for tone frequency set tings When the repeater requires a different tone system see p 20 Appears JBOD REPEATER OPERATION Push and hold PTT to transmit The displayed frequency automatically changes to the transmit frequency repeater input frequency If OFF appears confirm that the offset frequency p 21 is set correctly Release PTT to receive SET While receiving While transmitting Push MONIEN to check whether the other station s transmit signal can be received directly To return to simplex operation push LOW PIA for 1 sec once or twice to clear the or indicator To turn OFF the subaudible tone encoder push TONE I AN several times until no tone indicators ap pear J g S amp l N w Set the receive frequency repeater output fre quency pgs 9 10 Push pup 7 TONE to select minus duplex push pup 8 TSQL to s
88. n the sub transceiver dur Z ing cloning This will cause a cloning error When the display at left ap pears a cloning error has oc curred In such a case both trans ceivers automatically return to the clone standby condition and cloning must be repeated GENERAL e Frequency coverage USA Asia Australia unit MHz Tx 144 148 Rx 118 174 Europe Tx 144 146 Rx 118 174 Europe 1 Taiwan Korea Tx Rx 144 146 Guaranteed 144 148 MHz range only e Type of emission FM AM Receive only Number of memory channels 207 incl 6 scan edges and 1 call e Frequency resolution 5 10 12 5 15 20 25 30 50 kHz e Operating temperature range 10 C to 60 C 14 F to 140 F e Frequency stability 10 ppm 10 C to 60 C e Power supply requirement 13 8 V DC 15 e Current drain at 13 8 V DC approx Transmit at 65 W 15A Receive standby 0 8 A max audio 1 0 A e Antenna connector SO 239 50 9 e Dimensions proj not included 140 W x 40 H x 146 D mm 5 2 W x1 6 H x534 D in e Weight approx 1 25 kg 2 Ib 12 oz TRANSMITTER e Modulation system Output power approx Korea version Variable reactance frequency mod Power output eee i 1 Power Selection Taiwan High 65 W 50 Wi 24 W Midde 25W 10W Mid low 10W N A Low 5W 1 5 W SPECIFICATIONS 14 EE e Max frequency deviation e Spurious emissions e Microphone c
89. ncy communication mode is available for Digital modes operation In the emergency call no call sign setting is necessary Set the desired frequency then push BANK A for 1 sec to enter the option set mode Push BANK f gaal or V MHz several times to select the emergency setting then turns the emergency setting ON e EMG appears Operate the transceiver normal way To cancel the emergency communication mode push BANK ag for 1 sec then rotate DIAL to turn OFF E BANK OPTION N w gt DIGITAL MODE OPERATION 12 Set the desired frequency then BANK OPTION for 1 sec to enter the op tion set mode Push BANK OPTION or MR CALL sev eral times to select the emergency setting then turns the emergency setting ON e EMG appears Operate the transceiver normal way To cancel the emergency communication mode push BANK OPTION for 1 sec then push A or V to turn OFF 12 DIGITAL MODE OPERATION E Digital code Call sign squelch operation The digital code CSQL or call sign DSQL squelch opens only when receiving a voice signal with the same pre pro grammed digital code or call sign respectively The digital code or call sign squelch does not function while in a slow data communication Set the operating frequency Program the digital code or call sign in setting mode See p 69 Digital code setting or pgs 59 60
90. nd SQL to the desired level as in normal opera tion QG Push BANK Gag for 1 sec then rotate DIAL to turn Pager mode ON Select the desired transmit code channel Push SET or MONI Rotate DIAL to select the code channel Push any key other than indicated function keys to return to the pager operating condition 100 MHz digit shows P PYS td ao am SCA SET MONI Low ONT A s m or SCAN M CALL V MHz Fa me Fr ah Push PTT to transmit the pager code e Transmits the selected transmit codes and your ID automatically Wait for an answer back e When the transceiver receives an answer back code the func tion display shows the other member s ID or group code After confirming a connection push BANK i for 1 sec then turn the DIAL to select the code squelch op eration or repeat the previous key operation again to se lect non selective calling system Communicate with the other party as normal push PTT to transmit release to receive BA BANK OPTION Program the desired code channel in ad vance p 54 Set the operating frequency Push BANK OPTION for 1 sec then push A V to turn Pager mode ON Select the desired transmit code channel Push set B D OFF Push A V to select the code chan nel Push cLR A MW to return to the pager operating condition
91. ndicated function keys to exit option set mode TATA ha be A g Push and hold PTT to transmit and speak into the micro phone at normal voice level e Transmit indicator appears and the RF meter shows the output power Release PTT to return to receive e The other station call sign will be received e Received call signs can be stored into the received call record automatically See page 63 for details NOTE The digital mode operation is vastly different than FM mode One of the differences is in the digital mode the squelch does not function as FM mode changing the squelch setting will not open to hear the hiss of White Noise only activate for digital squelch function as CSQL Digital code squelch DSQL Call sign squelch or S meter squelch LLL BANK OPTION DIGITAL MODE OPERATION 12 Select the desired call sign Push BANK OPTION twice to select the call sign select mode e YUC appears Push A or V to select the desired call sign pre programmed or set the desired call sign see p 60 Push ctr A MW to exit option set mode Push and hold PTT to transmit and speak into the microphone at normal voice level e Transmit indicator appears and the RF meter shows the output power Release PTT to return to receive e The other station call sign will be received e Received call signs can be stored into the re ceived
92. nsferring memory Contents eee eee eee teenies E Programming channel names c c cece eee eect eeeteee E Memory clearing E Memory bank selection E Memory bank setting E Transferring bank contents CALL CHANNEL OPERATION E Call channel selection E Call channel transferring 1 0 0 0 eee eee eeeeeeeeeeeeteete E Programming a call channel ou eee eeeeeeteee SCAN OPERATION E Scatitypess 3 he Meith e r E A E a ti N Bi Scan start stop soa ainar ii L e NEA ATEA E Scan edges programming As E Skip channel setting 0 0 0 0 eee eee teeteeteeneteee M Scan resume Condition 000 0 eee teeter eee teen teeeeee 8 PRIORITY WATCH 43 44 E Priority watch types oo cece eee eeeeeeeeeeeeeeeeeeeeaeeaneaeeae 43 E Priority watch operation 0 eee eee e eee e teen eeeeeae 44 9 DTMF MEMORY ENCODER i E Programming a DTMF Code ou eee eee eee ee ee eeeeeeeeeaee 45 E Transmitting a DTMF Code 0 0 eee eee eee cece sees eee eeeeeaeeaee 46 MM DIME Speed arinira AEN PEE OE NEOS satausged tent 47 10 POCKET BEEP AND TONE SQUELCH E Pocket beep operation oo eee eee eee e cece eeee eee eeeeeeeaeeae E Tone DTCS squelch operation 0 0 cece eee ee eee E Tone scan 11 PAGER CODE SQUELCH Required Optional UT 108 52 57 E Pager function ccsiccndic ccna Ayin aN Eea bende AEE E Code programming a E Pager Operation si s ipicenniainyer raene iisa iani
93. ogramming 145 300 MHz into scan edges 1A Push 2 _ EA f z N Rotate for setting frequency etc s Mw OD n Push _ momentarily eee A aA 7s ILJU Lt IATA Te ea ed Ty een a a sb s aadd ae SET MONI LOW TONE M CALL V MHz SET MONI LOW TONE M CALL V MHz SET MONI LOW TONE M CALL ViMHz J COOCOO CO BB s Mw CD Rotate M Push _ for 1 sec and continue to push 11E l i va Beep oe ae Same LYS APA wel Oe Lgl AAA a A iaaa Si I Beep IAA tb am GJ Eu ap op ow O aw w o aw gm SET MONI Low TONE M CALL VIMHZz J SET MONI Low TONE M CALL V MHz SET MONI Low TONE M CALL V MHz 39 SCAN OPERATION 7 Programming scan edges via microphone f 1 Set the desired frequency in VFO mode To program a frequency for the other scan edge channels MW Push VFO LOCK to select VFO mode repeat steps 1 to 4 Ay Set the frequency via the keypad or A V Push FUNC then ctr A MW momentarily Push A or V to select scan edge channels 1A 2A or 3A Push FUNC then push ctr A MW for 1 sec to program 3 beeps sound and VFO is automatically selected e Memory channel number advances to the next scan edge channel 1b 2b or 3b when continuing to push cLR A MW after programming o N w A EXAMPLE Programming 145 800 MHZ into scan edges 1b Push
94. omentarily 8 Push FUNC then push moni 1 ANM to return to fre 3 Push set B D OFF quency indication if desired e Frequency readouts disappear 4 Push AJ to select the desired character e The selected character blinks EXAMPLE Programming CLUB into memory channel 15 Select memory channel 15 ay Push 22 or Ese to move aracter ERY push Gue then push a Pl to select the character o cursor ion Push epea previous _ steps l j H a ive a ee a ge ee a Cann a que SET MONI am MONI LOW TONE M CALL V MHz 30 5 MEMORY OPERATION E Memory clearing Contents of programmed memories can be cleared blanked if desired Push V MHzB eZNNI to select VFO mode Push S MW RA momentarily 0M indicator and the memory channel number blink Rotate DIAL to select the memory channel to be cleared e Memory channels not yet programmed are blank Push S MW QW momentarily then push S MW QW again for 1 sec t This operation must be performed within 1 5 sec 3 beeps sound then the frequency is cleared QQ indicator blinks continuously e When clearing the call channel the current VFO conditions are re programmed into the call channel automatically Push any key except S MW DMM to return to VFO mode Y NOTE Be careful the contents of cleared memories CANNOT be recalled EXAMPLE Clearing memory c
95. ondition See previous page for details Y NOTE If the pocket beep function is activated the trans G ceiver automatically selects the tone squelch function when priority watch starts MEMORY CHANNEL WATCH While operating on a VFO fre quency priority watch checks for a signal on the selected memory channel every 5 sec MEMORY SCAN WATCH While operating on a VFO fre quency priority watch checks for signals on each memory chan nel in sequence e The memory skip function is useful to speed up the scan Mch 1 SKIP frequency Meh 3_ CALL CHANNEL WATCH While operating on a VFO fre quency priority watch checks for signals on the call channel every 5 sec 5 sec 50 msec E Priority watch operation Select VFO mode then set an operating frequency Set the watching channel s For memory channel watch Select the desired memory channel For memory scan watch Select memory mode then push V IMHz RANN for 1 sec to start memory scan For call channel watch Select the call channel by pushing M CALL AAA once or twice Push M CALLGiille for 1 sec to start the watch e The transceiver checks the memory or call channel every 5 sec e The watch resumes according to the selected scan resume con dition p 42 e While the watch is pausing pushing M CALL Jie resumes the watch manually Push M CALL GGile to stop the watch prio Leus While pausing or
96. onnections Sa E QUICK REFERENCE GUIDE DC power supply connection Use a 13 8 V DC power supply with at least 15 A capacity Make sure the ground terminal of the DC power supply is grounded CONNECTING TO A DC POWER SUPPLY e See p 90 for fuse replacement IC 2200H DC power supply 13 8 V to an AC outlet Fuses 20 A QUICK REFERENCE GUIDE Antenna installation Antenna location To obtain maximum performance from the transceiver select a high quality antenna and mount it in a good location A non radial antenna should be used when using a magnetic mount Trunk mount Roof mount antenna antenna Drill a hole or use a magnetic mount Gutter mount antenna LS S N o O to antenna Antenna connector The antenna uses a PL 259 connector e PL 259 CONNECTOR oom Slide the coupling ring aj mmn down Strip the cable H gt jacket and soft solder Coupling ring 10 mm soft solder TOMM Soft Strip the cable as shown solder at left Soft solder the cen fe ter conductor 1 2 mm Slide the connector body solder solder X on and solder it o mil I Screw the coupling ring onto the connector body 10 mm in YX NY NOTE There are many publications covering proper an ZG tennas and their installation Check with your local dealer for more information and recommendations Connecting a microphone
97. onnector RECEIVER e Receive system e Intermediate frequencies e Sensitivity at 12 dB SINAD e Squelch sensitivity threshold e Selectivity Wide Narrow e Spurious and image rejection e AF output power at 13 8 V DC e Ext speaker connector Ext Data connector Some version only All stated specifications are subject to change without notice or obligation 5 0 kHz Wide 2 5 kHz Narrow Less than 60 dBc 8 pin modular 600 Q Double conversion superheterodyne 1st 21 7 MHz 2nd 450 kHz 0 14 uV typical 0 1 pV typical More than 6 kHz 6 dB Less than 14 kHz 60 dB More than 3 kHz 6 dB Less than 9 kHz 55 dB 75 dB typical More than 2 4 W at 10 distortion with an 8 Q load 3 conductor 3 5 d mm 8 Q 3 conductor 2 5 d mm 1 15 MAINTENANCE Troubleshooting If your transceiver seems to be malfunctioning please check the following points before sending it to a service center PROBLEM POSSIBLE CAUSE SOLUTION REF No power comes on Power connector has a poor contact e Check the connector pins e Polarity of the power connection is reversed e Re connect the power cable observing the proper pgs Il polarity Replace the fuse if damaged 90 Blown fuse e Check the cause then replace the fuse p 90 No sound comes from the Volume is too low e Rotate VOL clockwise p 13 speaker e The audio mute function is activated e Push any
98. r call sign into MYC YUC R1C and R2C Push BANK Ggag or V MHz several times to select the break in setting then turns the break in setting ON e BRK appears Vv MHz V MHz When both stations are in standby transmit to send a break in call Programmed call sign station receives the break in call as well as your call sign wWait for the reply call from the station who receive the break in call Atter receive the reply call communicate normal way To cancel the break in push BANK gg for 1 sec then rotate DIAL to turn OFF rn BANK OPTION While receiving an another stations com munication push BANK OPTION for 1 sec to enter the option set mode then set the either station repeater call sign into MYC YUC R1C and R2C Push BANK OPTION or MR CALL sev eral times to select the break in setting then turns the break in setting ON BRK appears When both stations are in standby trans mit to send a break in call Programmed call sign station receives the break in call as well as your call sign Wait for the reply call from the station who receive the break in call After receive the reply call communicate normal way To cancel the break in push BANK OP TION for 1 sec then push A or W to turn OFF E Emergency communication The emerge
99. ransmit release PTT to receive To cancel the tone squelch push FUNC then ENT C T OFF or disappears 10 POCKET BEEP AND TONE SQUELCH E Tone scan By monitoring a signal that is being operated with pocket beep tone or DTCS squelch function you can determine the tone frequency or DTCS code necessary to open a squelch Set the channel to be checked for a tone frequency or code Push TONE IEAA several times to select the tone condition or type to be scanned One of A n or appears Q Push TONE BS MN for 1 sec to start the tone scan To change the scanning direction rotate DIAL VAY co en ANM J w co ezm TONE M CALL V MHz SET MONI LOW TONE M CALL V MHz During CTCSS tone scan During DTCS code scan 4 NOTE The decoded tone frequency is programmed tem Z g porarily when a memory or call channel is selected How G ever this will be cleared when the memory call channel is 7 re selected MQ 51 When the CTCSS tone frequency or 3 digit DTCS code is matched the squelch opens and the tone frequency is temporarily programmed into the selected condition such as memory or call channel The tone scan pauses when a CTCSS tone frequency or 3 digit DTCS code is detected e The decoded CTCSS tone frequency or 3 digit DTCS code is used for the tone encoder or tone encoder decoder depending on the s
100. requency to 145 3625 MHz Push EA LOCK qn T SC PRIO SCAN SET MONI LOW TONE M CALL V MHz T oFF oe Push ire H o aD PRIO SET MONI Low TONE M CALL V MHz ana PUSH wont wena mo 5 Cc 7 x a Lf 3 DTM ae pa pe A g PRIO3 Low6 an oO oP G amp D CO EW SET MONI Low TONE M CALL V MHz T SCAN L im J Bi J 1 5 s Push ad YU these as D Op GD GM EW SET MONI Low TONE M CALL V MHz We hope these pointers have been helpful Now you are ready to call CQ lt QUICK REFERENCE GUIDE E Repeater operation 1 Setting duplex Push LOW JUG for 1 sec once or twice to select minus duplex or plus duplex e The USA version has an auto repeater function therefore setting duplex is not required 2 Repeater tone Push TONE IRAAN several times until s appears if the repeater requires a subaudible to be accessed j EDIS Using the HM 133V Plus or minus duplex selection and the repeater tone setting can be made easily via HM 133V Push pup 7 TONE for minus duplex pup 8 TSQL for plus duplex selection push FUNC then pup 7 TONE to turn the repeater tone ON Push 2 Ly h H fA My Taa 7 Push 3 Yb AV a MONI oo M CALL t eae ERNAS Push rue then cit Yb Ho am T SCAN co SCAN E
101. ries are available for your own call sign MYC other station call sign YUC and nearest re peater call sign R1C and another zone s repeater call sign R2C Each call sign memory can be stored up to 6 call signs and each call sign programmed up to 8 characters Your call sign programming Your call sign must be programmed for both Digital voice and slow data communications including GPS transmission Push BANK A for 1 sec then push BANK A or V MHz several times to select the call sign select mode e MYC appears DIGITAL MODE OPERATION 1 2 a NA aE pl SET MONI v MHz Rotate DIAL to select the desired call sign channel then push SET or MONI tal s Kd ilz SET MONI E Push MONI or SET to set into call sign programming condition e The 1st digit blinks and channel indication stops blinking Rotate DIAL to set the desired character or code e Push MONI or SET to move the cursor to left or right re spectively Push MONI or SET to select 2nd digit then rotate DIAL to set the desired character or code 2nd digit blinks 1st digit stop blinking e Repeat this step for programming your call sign r vi 1 ons SET non gt V MHz Push V MHz to fix the call sign Rotate DIAL to select an another channel from C1 to C6 Repeat steps to to program your call sign channels sine r
102. s 20 46 While in the digital mode operation with the installing an optional Digital unit UT 115 8 Ko 2 E Preparation Turning power ON OFF AA Push PWR for 1 sec to BL turn power ON and OFF Push PWR for 1 sec Osobu05050n00 VFO mode selection The transceiver has 2 basic operating modes VFO mode and memory mode Push V MHz Ke to select VFO mode JOC HH am SET MONI Low TONE VOVO co m M CALL V MHz Push VFO LOCK to select VFO mode j VFO LOCK SETTING A FREQUENCY E Using the tuning dial iD Rotate DIAL to set the frequency 9 HEBD TaS sr Ep Em DIAL oO If VFO mode is not selected push eat to select VFO mode The frequency changes according to the selected tuning steps p 11 To change the frequency in 1 MHz 10 MHz for some ver sions steps push V MHzEfef NN then rotate DIAL e Pushing V MHzEYeZNN for 1 sec starts scan function fc Wal ine G If scan starts push V MHz RJ again to cancel it am SET MONI Low TONE M CALL V MHz The display shows that the 1 MHz tuning step is selected Note that in this manual sections beginning with a micro phone icon as above designate operation via the HM 133V microphone E Using the keypad The
103. see p 70 e SPD appears e Select suitable data speed for your PC or application DIGITAL DIGITAL H THH wh eer co Do LA lz a DIGITAL MODE OPERATION 12 Start up the slow data communication application Set the application as follows e Port The same COM port number as IC 2200H s e Baud rate 4800 bps or 9600 bps same as step e Data 8 bit Parity None Stop 1 bit e Flow control Xon Xoff Transceiver automatically transmits or receive the data when you sending data to transceiver Or push and hold PTT to transmit release to receive the data manually e Refer to the instruction of the application that how to send or re ceive data Set the desired frequency BANK OPTION 2 Set another settings such as repeater dig ital code squelch transmit output power 3 Push BANK OPTION for 1 sec then push BANK OPTION or MR CALL to select the automatic transmission setting e ATX appears e Skip this setting if you want to transmit manually 4 Push BANK OPTION to select the data communication speed e SPD appears e Select suitable data speed for your PC or ap plication 5 Start up the slow data communication ap plication then follow step at above 12 DIGITAL MODE OPERATION E Other setting items Push BANK ag for 1 sec then push BANK egg or V MHz several times to select
104. so be adjusted with SQL4 sa_a D MUTE and sacw 16KEY L p C gm m SQLY LNI i4 e ee go ep E Monitor function This function is used to listen to weak signals without disturb ing the squelch setting or to open the squelch manually even when mute functions such as the tone squelch are in use the squelch e BUSY blinks Push MONIEN again to cancel the function 35 Push MONIEN to open Push moni 1 ANM to open the squelch MONI e Push mont 1 ANM again to cancel the function 1 X Y NOTE When SQL adjustment is set too far clockwise Z 12 17 o clock position the squelch attenuator is acti Y vated To monitor weak signals on the operating frequency Y deactivate the squelch attenuator function See p 82 for details WA E Audio mute function This function temporarily mutes the audio without disturbing the volume setting Push FUNC then sa_ amp D MUTE to mute MUTE audio signals e MUTE appears e Push ctr A MW or any other key to cancel the function Appears BASIC OPERATION 3 E Squelch attenuator The transceiver has an RF attenuator related to the squelch level setting Approx 10 dB attenuation is obtained at maxi mum setting Rotate SQL clockwise past the 12 o clock position to ac tivate the squelch attenuator e Attenuation level can be adjusted up to 10 dB approx between 12 o
105. swer back call and display the operating frequency 5 After confirming a connection push BANK OPTION for 1 sec to select code squelch operation or repeat the previous key operation again to select non selective calling system w PAGER CODE SQUELCH 11 e PERSONAL CALLS A GX L HeH re EPE TF blink a e GROUP CALLS a C HA te Code channel ERROR INFORMATION Previously received code This display appears when you are called with your ID code and the calling station s ID code is 424 This display appears when you are called with the group code 888 and 888 has been programmed into code chan nel C6 When the transceiver re ceives an incomplete signal E and previously received code appear 11 PAGER CODE SQUELCH E Code squelch Code squelch provides communications with quiet standby since you will only receive calls from stations which know your ID or group code Each push of PTT sends a 3 digit code in order to open the receiving station s code squelch prior to voice transmission Set the operating frequency e Set the AF and squelch to the desired level as in normal opera tion Push BANK 0 for 1 sec then rotate DIAL to select code squelch mode CS appears Select the desired transmit code channel Push SET or MONI Rotate DIAL to select the code channel Push
106. switch or key to deactivate it p 14 e Squelch is set too tight e Set the squelch level to the threshold p 13 A selective call or squelch function is activated e Turn the appropriate function OFF pgs 48 such as pocket beep or tone squelch 49 50 Sensitivity is low and only Antenna feedline or the antenna connector solder Check and if necessary replace the feedline or sol p III strong signals are audible has a poor contact or is short circuited der the antenna connector again e Squelch attenuator function is activated e Set SQL between 10 12 o clock position p 14 No contact possible with The other station is using tone squelch e Turn the tone squelch function ON p 50 another station The transceiver is set to duplex e Set to simplex p 17 Repeater cannot be ac Wrong offset frequency is programmed e Correct the offset frequency p 21 cessed e Wrong subaudible tone frequency is programmed Correct the subaudible tone frequency p 19 Frequency cannot be set The frequency lock function is activated e Turn the function OFF p 12 e Priority watch is paused on the watching frequency e Push M CALL REI to cancel the watch p 44 Frequency cannot be set The frequency lock function is activated e Push SET KA for 1 sec to deactivate the fre p 12 via the microphone quency lock function e The microphone keypad lock function is activated e Push FUNC then 16
107. tches ZG the frequency intervals of repeaters in your area Push V MHzE eXiq to se lect VFO mode if neces sary Push SET Hee to enter set mode Push SET or MONI sev 23S eral times until TS appears Ly 224 as shown at left hee Sara Rotate DIAL to select the desired tuning step i Push any key other than in dicated function keys to exit set mode DIAL 15 kHz tuning step USING SET MODE o Push VFO LOCK to select VFO mode if 2 Push set B D OFF to enter set mode 3 Push set B D OFF or ent C T OFF several times until TS appears Push A or V to select the desired tun Push ctr A MW to exit set mode E Lock functions To prevent accidental channel changes and unnecessary function access use the lock function The transceiver has 2 different lock functions Frequency lock This function locks DIAL and keys electronically and can be used together with the microphone lock function Push SET for 1 sec to turn the lock func tion ON and OFF PTT MONIEN VOL and SQL can be used while the channel lock function is in use Also TONE 1 TONE 2 DTMF tones or DTMF mem ory contents can be transmit ano ea SCAN SET MONI LOW TONE M CALL V MHz ted from the microphone Boop c Push VFO LOCK for 1 sec to switch the l VFO LOCK lo
108. tion p 77 gt eae re Bank link setting p 7 Pt eng Wis IM Wide Nar selection p 78 R F FM AM FM mode select p 78 0F Tuning step p 76 Weather alert p 78 MODE ARRANGEMENT 17 INITIAL SET MODE Turn power ON while pushing gt HER LN Beep tone on off p 80 Time out timer T 80 TEN 1IL S meter ehe T T i sam Auto repeater p 80 POE DF Auto power off p 81 DTMF speed p 82 Display type p 82 Z gt e E ATT ON PLO OF Squelch attenuator p 82 Repeater lockout p 81 ALE OF ALC function p 82 Count on us 02 Europe lt Intended Country of Use gt 12 Europe 1 GER mFRA ESP mm SWE HAUT WENED EPOR DEN E GBR BEL WITA E FIN MIRL ELUX GRE SUI E NOR A 6329H 1EX Printed in Japan Icom Inc 2003 Icom Inc 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan
109. ull programmed scan with V MHz ExefNX or memory mode for memory scan with M CALLGiaile e Select the desired bank with BANK egg for bank scan Set the squelch to the point where noise is just muted Push V MHz RAN for 1 sec to start the scan e To change the scanning direction rotate DIAL The memory channel readout blinks the scan type as follows Push SET KA to switch full and programmed scan P1 P2 and P3 To stop the scan push SET KIAJ or V MHz Rey e During full scan e During programmed scan HSARA al WANs E eu AS TONE Pratt ns LOCK SET oot one LON TONE frit e During memory scan HS SAB Pi T gt Em SGAN NS GZA T Sion LUN TONE MCAL fate SCAN OPERATION 7 SJ 1 Push VFO LOCK to select VFO mode for full programmed scan push MR CALL to se lect memory mode for memory scan Push BANK OPTION to select a bank for bank Bc SET scan 8 2 Set the squelch to the point where noise is just muted 3 Push scan 2 T SCAN to start the scan e Push A or V for 1 sec also starts the scan 4 Push set B D OFF to switch full and pro grammed scan P1 P2 and P3 5 To stop the scan push scan 2 T SCAN or ctr A MW e During Bank scan HA sap TNS GSE Sion LUN TONE MCRL fae BAM ap T gt Em BLO OV VUV BLUON Push J C to select full Indicates scan edge c
110. ut power HIGH mip 5 DTCS _ for middle output power push again for mid low output power and Low 6 DTMF for low output power e The output power can be changed via the microphone during receive only 2 Jes JE R BASIC OPERATION 3 E One touch PTT function The PTT switch can be operated as a one touch PTT switch each push switches between transmit receive Using this function you can transmit without pushing and holding the PTT switch To prevent accidental continuous transmissions with this function the transceiver has a time out timer See p 80 for details a Push FUNC then prio 3 PTT M to turn the PTT M one touch PTT function ON e The activity indicator lights green Push PTT to transmit and push again to re ceive Two beeps sound when transmission is started and a long beep sounds when returning to receive S flashes when transmitting with the one touch N PTT function ziz F lt E a ry alld Ht haki g MONI Low D Ta ae 3 Push FUNC then prio 3 PTT M to turn the one touch PTT function OFF e The activity indicator goes out 4 E Accessing a repeater Set the receive frequency repeater output frequency pgs 9 10 2 Push LOW JG for 1 sec once or twice to select minus duplex or plus duplex or appears to indicate the transmit frequency for minus shift or plus shift respectively e Whe
111. y in VFO mode VFO CALL Push VFO LOCK to select VFO mode Set the desired frequency in VFO mode Ay Set the frequency Push V MHzEXeZAN to select VFO mode Th Set other data as desired Set the frequency using DIAL 2 Push FUNC then ctr A MW momentarily Set other data as desired 3 Select the call channel via A or V Push S MW QW momentarily fori 4 Push FUNC then ctr A MW for 1 sec to Rotate DIAL to select the call channel M indicator and C blink program 3 beeps sound and the unit returns to VFO mode automatically 4 EXAMPLE Programming 145 120 MHZ into the call channel via the microphone Push to select VFO mode oe thie frequency T Push 0 then 4 momentarily care uu aa G s Gaia Geaa 3 LIE COA MIE ITA LIE AA Hektik f Hh id B Yo Wie gi Gon Tow Sone monL Vinin2 Siow tow wean Vine Sion Tow mea SMa Push until large C appears Push then for 1 sec gt D yc mes h JE JIA o ia LIC IIA ass 4 OLLI T JUA Bee 7 TILJL FLITA s Uaa Tz 12 EC Ll p Beep Hh ie fr S Sor Tow mae Se Go Don Tom MoAL Vaie i Sow Cow Saxe ican Slane 36 O A SCAN OPERATION E Scan types Scanning searches for signals automatically and makes it There are 3 scan types and 4 resume conditions to suit your easier

Icom IC-2200H - Orchard City Amateur Radio Club

Contents

Download Pdf Manuals

Related Search

Related Contents