User Manual - Aarcomm Systems Inc
Contents
1. om Date August 2013 RM1 900MRTR OEM Installation Manual Technical Support Phone 1 604 379 5091 Email support aarcomm com 112 17 Fawcett Rd Coquitlam BC Canada V3K 6V2 Revision 4 Page 1 Ce Model RM1 900MRTR FCC ID 2AAXW900MRM1 IC 11295A 900MRM1 FLBL 11001 01 Made in Canada OEM Installation Manual The Aarcomm model RM1 900MRTR is a frequency hopped spread spectrum FHSS transceiver module designed to be compatible with U S FCC Part 15 247 and Canadian RSS 210 regulations for license free use in the 902 928MHz ISM band The RM1 900MRTR is a high quality system on chip SOC FHSS transceiver design The major elements include a frequency agile SOC transceiver integrated circuit LNA PA T R switch harmonic filter and an embedded microprocessor for frequency hopping sequence generation and data generation Packets of data are transmitted to and received from a mating transceiver The RM1 900MRTR is intended to be used with a host processor with an SPI UART or USB interface We have provided a software stack for the host processor to make it easy to interface with the RM1 900MRTR Date August 2013 112 17 Fawcett Rd Coquitlam BC Canada V3K 6V2 Revision 4 Page 2 O 11Din This information should be referenced when designing the host interface PCB to the RM1 900MRTR Date August 2013 OEM Installation Manual Power requiremen2. with the manufacturer s other labelling requirements IMPORTANT Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement IMPORTANT To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that permitted for successful communication Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit n cessaire l tablissement d une communication satisfaisante IMPORTANT The installer of t
3. 5 declaration of conformity Section 2 925 e This module is to be installed only in mobile or fixed applications Please refer to FCC CFR 47 Part 2 1091 b for a definition of mobile and fixed devices Separate approval is required for all other operating configurations including portable configurations with respect to FCC CFR 47 Part 2 1093 and different antenna configurations The antenna used with this module must be installed to provide a separation distance of at least 20cm from all persons and must not be co located or transmit simultaneously with any other antenna or transmitter except in accordance with FCC multi transmitter product procedures FCC Exposure Requirements To satisfy FCC RF exposure requirements for mobile transmitting devices a separation distance of 20cm or more should be maintained between the antenna of this device and persons during operation To ensure compliance operations at closer distances than this are not recommended Notice This transmitter module has been certified for FCC Part 15 operation when installed in a host device the host manufacturer is responsible for making sure that the host device with the transmitter installed continues to be compliant with Part 15 Subpart B requirements This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfe
4. g two conditions i this device may not cause harmful interference and ii this device must accept any interference received including interference that may cause undesired operation WARNING The Original Equipment Manufacturer OEM must ensure that the OEM modular transmitter must be labeled with its own FCC ID number This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below If the FCC ID is not visible when the equipment is installed inside another device then the outside of the device into which the equipment is installed must also display a label referring to the enclosed equipment IMPORTANT This equipment complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC 15 19 IMPORTANT The RM1 900MRTR Module has been certified by the FCC for use with other products without any further certification as per FCC section 2 1091 Modifications not expressly approved by Aarcomm Systems Inc could void the user s authority to operate the equipment OEM INSTRUCTIONS The RM1 900MRTR Module is limited to OEM installations only OEM ee must ensure that the end user has no manual instructions to remove or install the module OEM s must comply with FCC marking regulation part 1
5. his radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population Consult Safety Code 6 obtainable from Health Canada s website www hc sc gc ca rpb Date August 2013 112 17 Fawcett Rd Coquitlam BC Canada V3K 6V2 Revision 4 Page 5 AARCOMM OEM Installation Manual IMPORTANT This radio transmitter has been approved to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater than the maximum gain indicated for that type are strictly prohibited for use with this device CNE AE a Gain dBi NMOSPEC900 Pulse Electronics 5 8 over 1 4X whip 5 4 NMOMMRDS 2 Q900 Pulse Electronics 1 4 whip 3 5 LMB ANsiciict 9n12 119 Cauarrott RA Cnn klara D Sw Aa VAK C 9 Daician 1 Dapa E August 2013 112 17 Fawcett Rd Coquitlam BC Canada V3K 6V2 evision 4 Page 6
6. rence in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect equipment and receiver to outlets on different circuits or Consult the dealer or an experienced radio TV technician for help Date August 2013 112 17 Fawcett Rd Coquitlam BC Canada V3K 6V2 Revision 4 Page 4 Canada IC Q AARCOMM OEM Installation Manual Equipment is subject to certification under the applicable RSSs shall be permanently labelled on each item or as an inseparable combination The label must contain the following information for full compliance Certification Number IC 11295A 900MRM1 Manufacturer s Name Trade Name or Brand Name AARCOMM SYSTEMS INC Model Name RM1 900MRTR IMPORTANT This equipment for which a certificate has been issued is not considered certified if it is not properly labelled The information on the Canadian label can be combined
7. ts RF connector Host connector 112 17 Fawcett Rd Coquitlam BC Canada V3K 6V2 Pinout 1 USB_P 2 USB_N 3 GND 4 VBUS 5 SPI_SOMI 6 SPI_CLK 7 SPI SIMO 8 TX 9 ISPI TE 10 RX 11 4V output 12 4V output 13 TX2 14 Vrtc 15 Vin 16 Vin 17 RX2 18 GPIO1 19 GND 20 Link 21 GND 22 RSSI 23 GPIO2 24 DAC GPIO3 25 GND 26 nPOR Vin range 7 to 40 VDC 24 VDC 250mA Height RM1 900MRTR S straight MCX RM1 900MRTR L right angle MCX RM1 900MRTR R right angle MCX 0 05 x 0 05 pitch female 2x13 26 position RM1 900MRTR S 0 45 RM1 900MRTR L 0 16 RM1 900MRTR R right angle Revision 4 Page 3 AARCOMM OEM Installation Manual United States FCC This equipment complies with Part 15 of the FCC rules and regulations To fulfill FCC Certification requirements an OEM manufacturer must comply with the following regulations 1 The modular transmitter must be labelled with its own FCC ID number and if the FCC ID is not visible when the module is installed inside another device then the outside of the device into which the module is installed must also display a label referring to the enclosed module 2 The module may only be used with antennas that have been tested and approved for use Example of label required for OEM product containing RM1 900MRTR module Contains FCC ID 2AAXW900MRM1 The enclosed device complies with Part 15 of the FCC Rules Operation is subject to the followin
Download Pdf Manuals
Related Search