SPA941 User`s Manual
Contents
1. Do not place in humid and dusty area The device may malfunction cause electric shock and fire Do not place in extremely cold place or place with unstable temperature It may cause explosion Do not place in unstable or shaky place If the device falls it may collapse it may cause injury or explosion Use after checking if foreign matters are attached to the speaker of the handset Thumbtacks pin stapler wires and other metallic object may cling to the magnet of the speaker so please be careful Troubleshooting Before requesting repair please check again the following If the problem persists please contact agile shop at sup agile ne jp SYMPTOM CAUSE TREATMENT General Failure Please disconnect and reconnect the power cable Please do it a few times Please wait at least one minute Until you disconnect and reconnect the power cable If no improvement above is made contact the Name of the manufacturer to shop agile ne jp Please let us know your number and broadband products No ringer sound Ethernet cable is Please check the connection of the Ethernet cable disconnected AC adapter is Please check the connection of the AC adapter Please adjust the volume on the volume button disconnected Do you want to revert the changed settings disconnect the Ethernet cable Please reboot Did you change the settings for volume Did you change the settings on the display Call is interrupted by Are t2. Audio Configuration Preferred Codec Use Pref Codec Only 729a Enable G723 Enable 726 16 Enable G726 24 Enable 726 32 Enable G726 40 Enable Release Unused Codec DTMF Process AVT silence Supp Enable DTMF Tx Method Dial Plan Dial Plan xx 3469 11 0 00 2 9 xxxxxx 1xxx 2 9 xxxxxxSO xxxxXxXxKXxKXXXxX Enable IP Dialing yes Undo All Changes omit All Chang Proxy Enter the VOIP Server Display Name amp Auth ID amp User ID Enter Unique 10 digits Password After registration an email that contains password will be sent to you Enter the password If the Unique password has been changed in Unique Management page enter the new password Use Auth ID Choose YES Audio Configuration Enter and type the settings same as the screen above Dial Plan xx x x x x x x x x x x x x x x Type all the character If the input is incorrect you will not able to connect or make a call If Line Key2 is enabled apply the same setting in EXT 2 3 and 4 tabs Once done click Submit all Changes The device will be restarted and the settings will be applied Safety Precautions This manual contains precautions to assure user s safety while using this product If the precautions are disregarded the extent of consequences is presented below A This indicates that ignoring or mishandling of this notice might result to death or serious injury to the person WA
3. Confirming various settings and contacts phone numbers are possible G Voice mail indicator light Lights up when there is a voicemail message 4 Lines Used for viewing the account information Soft buttons Can select the top item on the screen Navigation button Moving the cursor in the display menu is possible D Mailbox button Use to check voicemail Hold button Hold button Setup button Use to check information stored in your phone Volume adjustment bar Used for adjusting the volume 1 Headset button Use to connect a headset to the device 12 Speaker button Hands free feature It is possible to call without picking up the handset 13 Mute button The partner will not be able to hear your voice while at the middle of the call Dial pad Use to dial phone number Setup Method 1 Confirm SPA941 s IP address Press the Setup button on the console Setup menu is displayed on the LCD screen Navigation buttons Select the Network on the left soft button Press Select 2 From a web browser open the configuration page SPA941 and PC must be connected to the same network Start Internet Explorer web browser etc Enter IP address following the format below http IP address Example If the IP address is 192 168 001 002 it should be entered as http 192 168 1 2 3 Screen Setting will be displayed in the web browser Click the Adminilogin found at the top right corner of the screen Click the Adv
4. RNING A This indicates that ignoring or mishandling of this notice might result to harm to the person CAUTION i O OOOO O OOOO ODO O WARNING Immediately unplug the device from the power supply if there is a strange smell and smoke Don t use the device and immediately contact the dealer for repair This may cause fire or explosion Do not disassemble or modify The device may malfunction cause electric shock and fire Do not insert metal to the opening or drop the product If in case a metal is inserted to the device unplug the device and contact the dealer The device may malfunction cause electric shock and fire Do not pour water or any foreign object inside the device If in case water or any foreign object is poured or inserted to the device unplug the device and contact the dealer Do not touch the device when lightning occurs This may cause electric shock Do not use in bathroom or shower room The device may malfunction cause electric shock and fire Don t place in a damp dusty or direct sunlight The device may malfunction cause electric shock and fire This device is not waterproof If in case water entered the device unplug the device and contact the dealer A CAUTION Do not place near the kitchen table or humidifier or near oil and moisture The device may malfunction cause electric shock and fire Do not place near direct sunlight The internal temperature might do up and may cause fire
5. SPA941 User s Manual Thank you for purchasing the SPA941 Before using the product please read the manual carefully After reading store the manual in an accessible place Check if all the accessories attachments are included in the package e SPA941 Main body e AC adapter e Handset e Curl Handset cord e Ethernet Cable e Base LINKSYS SPA941 OVERVIEW Stylish and functional in design the SPA941 VoIP Phone is ideal for a residence or business that uses hosted IP telephony service an IP PBX or a large scale IP Centrex deployment The SPA941 leverages industry leading VoIP technology from Linksys to deliver an upgradeable high quality IP Phone that is unparalleled in features value and support DISCLAIMER e Features and specifications may be updated without prior notice e The company shall not assume any responsibility for the development of noise and volume interruption and disconnection of calls that arise from the customer and this company s network system Also please be advised that call quality is not guaranteed e The company shall not assume any responsibility for inconsistency in call quality brought about by individual listening skills e The company shall not assume any responsibility for the device damage that occurred outside Japan e Services may stop temporarily without prior notice due to GXP1400 s scheduled maintenance e The company shall not assume any responsibility in the event that the phon
6. ance tab 4 Click on the System tab at the top of the screen Then set the following SIPURA technology inc Sipura Telephone Configuration Provisioning Regional Phone Ext 1 Ext 2 User TET rsonal Direct Cal Histon System Configuration Restricted Access Domains bid Enable Web Server yes bid Enable Web Admin Access yes User Password Internet Connection Type DHCP yes Static IP Gateway Optional Network Configuration HostName Primary DNS DNS Server Order Manual X Syslog Server Debug Level Secondary NTP Server ntp jst mfeed ad jp VLAN Settings Enable VLAN no d gt Web Server Port Admin Passwd NetMask Domain Secondary DNS DNS Query Mode Debug Server Primary NTP Server VLAN ID 80 a Parallel 7 ntp jst mfeed ad jp Undo All Changes User Logn basic advanced Copyright 2003 2005 Sipura Technology All Rights Reserved Primary NTP Server amp Secondary NTP Server Enter ntp jst mfeed ad jp Submit All Changes 5 Click on the Regional tab at the top of the screen Set this by following the screen shot in the next page Miscellaneous Set Local Date mm dd Set Local Time HH mm Time Offset HH mm Time Zone GMT 08 00 4 Daylight Saving Time Rule DTMF Playback Level 16 DTMF Playback Length 1 Inband DTMF Boost 12dB Undo All Changes Submit All Chang
7. e Enable NAT Keep Alive Msg SNOTIFY NAT Keep Alive Dest Network Settings SIP TOS DiffServ Value 0x68 SIP CoS Value 3 9 RTP TOS DiffServ Value Oxb8 RTP CoS Value 6 3 Network Jitter Level high 7 Jitter Buffer Adjustment up and down SIP Settings SIP Port 5060 SIP 100REL Enable no EXT SIP Port Auth Resync Reboot yes SIP Proxy Require SIP Remote Party ID no s Referor Bye Delay 4 Refer To Target Contact yes Referee Bye Delay 0 SIP Debug Option none Refer Target Bye Delay 0 Sticky 183 no F Call Feature Settings Blind Attn Xfer Enable MOH Server a gt Message Waiting Default Ring Auth Page no Auth Page Realm Conference Bridge URL Mailbox ID State Agent n CFWD Notify Serv no CFWD Notifier Auth Page Password Voice Mail Server q gt NAT Keep Alive Enable Choose YES Mailbox ID Choose 999 When recording a voicemail LED function will blink Function MWI The message waiting is set ON d gt Proxy and Registration Proxy VOIP Server se Outbound Proxy no Outbound Proxy Use OB Proxy In Dialog yes Register yes Make Call Without Reg no Register Expires 3600 Ans Call Without Reg no Use DNS SRV no F DNS SRV Auto Prefix no Proxy Fallback Intvl 3600 Proxy Redundancy Method Normal Subscriber Information Display Name UID ser ID Password Password se Auth ID Auth ID UID Mini Certificate SRTP Private Key
8. e can no longer be used for calling due to damage or malfunction MAINTENANCE Please wipe it with a soft dry cloth Do not use wet rag Volatile chemicals such as benzene or thinner as they may damage the main body please do not use When using rag chemicals make sure that you read and understand the directions completely Connection Method 1 Connect the 1 end of the cord to the handset and the other end to the body handset port 2 Plugged the Ethernet cable LAN to the rear body of the GXP 280 285 LAN port then plugged into the network or broadband router 3 Plug in the AC adapter into the electrical outlet 4 Insert the AC adapter to the body Be sure to observe the order of the connection Make sure that the adaptor is plugged in properly It will take some time to call after connecting so please wait for a moment SPA941 The SPA941 is a phone that can be used at Agile Phone It cannot be used as a typical subscriber phone The customer must subscribe to an Internet Service Provider to be able to use the device Customer with no broadband router fe dsa anced i 2 Q DOOOOG s s o 4 14 1 Handset 8 Hold button 2 LCD screen 9 Setup button 3 Voice moal indicofor ign 10 Voume ocjustment bor 4 Lines SPAS41 amp SPAS42 11 Heoctset button 5 Soft buttons 12 Speaker Dutton 6 Navigation button 13 Mute button 7 Mailbox button 14 Dial pod Handset Handset D LCD screen Display
9. es Time zone Select GMT 09 00 or your preferred location a a i Phone User Logn basic advanced Info System SIP Provisioning Regional Ext 1 Ext 2 User Seanad ar Col tebe General Station Name Voice Mail Number Text Logo Line Key 1 Extension 1 Short Name Share Call Appearance private Line Key 2 Extension Disabled Short Name Share Call Appearance private Line Key 3 Extension Disabled Short Name Share Call Appearance private Line Key 4 Extension Disabled Short Name Share Call Appearance private Short Name Enter the extension number appear on the display screen Ex 200 Extension Select Disable if the line key is not in use Voice Mail Number Enter 999 In the SPA941 using a separate extension number from Line key 1 to Line key 4 is possible When using a separate extension numbers in Extension set the extension number on the previously configured extension line If one extension number is used set the Line Key 2 to Disabled At the upper part of the page click Ext 1 Follow the setup in the screenshot in next page SIPURA technology inc Sipura Telephone Configuration ii User Login advanced Info System SIP Provisioning Regional Pho GO t2 User mana araa farger General Line Enable yes Share Line Appearance Share Ext private Shared User ID Subscription Expires 3600 NAT Settings NAT Mapping Enable no F NAT Keep Aliv
10. here any abnormalities in Please check your network the noise the network environment environment to repair the problem Initialization Method Clears all data initialization process s Information must be set to initialize the service again 1 Note the OQOOB8200XXXX MAC address located on the bottom of the unit 2 Press the Console MENU button y several times press display Restore Factory Setting and in the Config 3 Enter the MAC address Check the website FAQ and for more information on the features and settings visit http www agile ne jo support We accept inquiries by telephone and email mailto sup agile ne jp Telephone number 636 5 150603 Weekdays 10 00 19 00
Download Pdf Manuals
Related Search