Initimidator Scan/Barrel 305 IRC User Manual Rev. 1
Contents
1. D o E o 20 PREV 20 GING REVE SG 20 EE 20 Ric EET P OT O T O de 21 Reset to Factory Defaults nan renan PRE K REO RAK R snis KERR SOPKA KR SS KA KK annis 21 S StS AO ELE 21 dere 22 RE COPO o LE 22 Configuration Master Slave 23 Conngurindhe Slaves arte tee Seed teat eh ouha ede res E a d d Cal eed i a 23 Gong ning ME MASTER zevenen ended deet nado fondo ESA ana tr okolo o houba la ooo Si sad 23 5 Technical IMTONMAUON z zdesikisuuak mekssok soba M 24 Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 2 of 27 Product Maintenance 6 Technical Specifications Returns Contact Us Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 3 of 27 1 BEFORE YOU BEGIN What is Intimidator Scan 305 IRC Power Cord Included or Warranty Card Intimidator Barrel 305 IRC Quick Reference Guide Unpacking Carefully unpack the product immediately and check that all the parts are in the package and are in good condition Instructions Claims the box or any of the contents appear damaged from shipping or show signs of mishandling save all packaging and file a claim with the carrier immediately do not notify Chauvet Failure to report damage to the carr2. or DOWN to highlight the Factory Set option Press ENTER The product will immediately reset to factory default settings MPD System To see the product s current software version running mode DMX address and temperature do Information the following 1 Press MENU repeatedly until 4 icons show on the display 2 Use UP or lt DOWNS to highlight the Sys Info icon 3 Press lt ENTER gt The current information about the product will show on the display Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 21 of 27 IR Mode IR mode allows the product to be controlled with an infrared remote controller The IRC 6 can remotely set the product to various modes adjust the color speed and sensitivity and set the strobe To set the product to IR mode do the following Make sure the product is plugged into a power source and not connected to a DMX cable Press lt MENU gt repeatedly until 4 icons show on the display Use lt UP gt or lt DOWNS to highlight the Run Mode icon Press lt ENTER gt The Run Mode options will show on the display Use lt UP gt or DOWN to highlight the IR option Press lt ENTER gt A green dot will show on the IR option line and the product will begin moving and emitting light oi Se IRC 6 Operation The IRC 6 infrared controller available from Chauvet allows remote control of the Intimidator Scan Barrel 305 IRC Be sure the IRC 6 remote is pointing directly at the product
3. U 076 Synchronized Strobe slow to fast 077 U 145 Pulse Strobe slow to fast 146 U 215 Random Strobe slow to fast 216 255 Open Tilt Scan Tilt Barrel 3 Color 4 Shutter Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 17 of 27 7CH Channel Function Value Percent Setting 2 3 4 5 6 7 000 U 007 Open 008 015 Gobo 1 glass 016 023 Gobo 2 glass 024 U 031 Gobo 3 032 U 039 Gobo 4 040 U 047 Gobo 5 048 U 055 Gobo 6 Gobo Wheel 056 063 Gobo 7 064 U 071 Gobo 7 shake fast to slow 072 U 079 Gobo 6 shake fast to slow 080 U 087 Gobo 5 shake fast to slow 088 U 095 Gobo 4 shake fast to slow 096 U 103 Gobo 3 shake fast to slow 104 U 111 Gobo 2 glass shake fast to slow 112 119 Gobo 1 glass shake fast to slow 120 127 Open 128 191 Gobo scroll counter clockwise rotation 192 255 Gobo scroll clockwise rotation 5 000 063 Gobo indexing l 064 147 Rotate clockwise slow to fast 6 Gobo Rotation z 148 U 231 Rotate counter clockwise slow to fast 232 U 255 Gobo bounce 7 000 U 007 Prism 008 255 Stop static prism effect Prism Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 18 of 27 Configuration Standalone O Sound Mode LA Auto Mode Manual Mode Use standalone configurations to operate the product without a DMX controller Never connect a product operating in a standalone mode
4. and there is nothing in between the remote and the product Some of the buttons on the remote work differently than what is indicated on their labels For example lt MANUAL gt controls the gobo selection lt R gt lt G gt lt B gt lt A gt lt UV gt and lt W gt control the other manual functions Please read the next section carefully I The list below describes which features each button controls lt BLACKOUT gt Turns LEDs on and off AUTO Activates Auto mode Use the lt gt and lt gt buttons to cycle through Auto modes SOUND Activates Sound mode lt STROBE gt Activates the strobe Use the lt gt and lt gt buttons to cycle through strobe speeds lt SPEED gt Adjusts the movement speed Use the lt gt and lt gt buttons to cycle through movement speeds lt SENSITIVITY gt Adjusts sound sensitivity Use the lt gt and lt gt buttons to cycle through sound sensitivity levels lt gt Adjusts the brightness of the LEDs Use the lt gt and lt gt buttons to increase or decrease the brightness of the LEDs lt MANUAL gt Cycle through static gobos lt FADE SNAP gt or lt FADE gt Cycle through static colors lt R gt Sets the color wheel rotation speed Use the lt gt and lt gt buttons to increase or decrease the color wheel rotation speed lt G gt Sets the gobo wheel rotation speed Use the lt gt and lt gt buttons to increase or decrease the
5. chain Once set and connected the slaves will operate identically to and in unison with the master Always put the male DMX connector into the master Do not connect to the DMX In port on the master Never connect more than 31 slaves to the master Never connect a DMX controller to a DMX daisy chain of master and slaves Configure all the slaves before connecting the master to the DMX daisy chain Configure the slaves for Slave mode before or after they are put in position and before they are daisy chained to the master To configure a slave do the following Make sure the product is connected to a power source Press lt MENU gt repeatedly until 4 icons show on the display Use UP or lt DOWNS to highlight the Run Mode icon Press lt ENTER gt The Run Mode options will show on the display Use UP or DOWN to highlight the Slave option Press ENTER The current Slave mode will be highlighted Use UP or DOWN to select the Slave mode Select Slave1 for 10096 synchronized actions Select Slave2 Slave3 or Slave4 for a delayed show creating a wave effect QUOS GIA IMS Configure the master after all the slaves are connected to it and configured To configure the master do the following 1 Make sure the product is connected to a power source and connected to all of the slaves 2 Press lt MENU gt repeatedly until 4 icons show on the display 3 Use UP or DOWN to highlight the Run Mode icon 4 Selec
6. on a properly affixed label DO NOT write the RMA number directly on the box Before sending the product clearly write the following information on a piece of paper and place it inside the box Your name Your address Your phone number RMA number A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be your responsibility FedEx packing or double boxing are recommended Chauvet reserves the right to use its own discretion to repair or replace returned product s Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 26 of 27 CONTACT US WORLD HEADQUARTERS Chauvet General Information Address 5200 NW 108 Avenue Sunrise FL 33351 Voice 954 577 4455 Fax 954 929 5560 Toll free 800 762 1084 Technical Support Voice 954 577 4455 Press 4 Fax 954 756 8015 Email tech chauvetlighting com World Wide Web www chauvetlighting com UNITED KINGDOM AND IRELAND Chauvet Europe Ltd General Information Address Unit 1C Brookhill Road Industrial Estate Pinxton Nottingham UK NG16 6NT Voice 44 0 1773 511115 Fax 44 0 1773 511110 MEXICO Chauvet Mexico General Information Address Av Santa Ana 30 Parque Industrial Lerma Lerma Mexico C P 52000 Voice 52 728 285 5000 CHAUVET EUROPE Chauvet Europe BVBA General Information Address Stokstraat 18 9770 Kruishoutem Belgium Voice 329 388 93 97 Tech
7. recommendations in the Safety Notes section Orientation The Intimidator Scan Barrel 305 IRC can be mounted in any position but make sure the placement allows adequate ventilation for the product and allows for movement of the yoke and head in any direction Rigging Be sure to place the product in a location that allows easy access to it for maintenance and programming and enough space around the product for ventilation Make sure that the structure or surface onto which the product will be mounted can support the product s weight For more information see the Technical Specifications section When mounting the product overhead always use a safety cable and make sure the product is attached securely When mounting the product on a truss or pipe use a mounting clamp with the appropriate weight capacity Chauvet has a full range of mounting clamps See http Awww chauvetlighting com cables clamps main html for the complete selection The rubber feet serve as floor supports When placing the product on the floor make sure that the product and cables are away from people and vehicles Mounting Clamps such as CLP 15 from Chauvet f Safety Cable o such as CH 05 from 4 Chauvet Bracket Secure the safety cable using the pass through on the back of the product Rubber Feet x4 Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 10 of 27 4 OPERATION Control Panel he control panel is used to
8. 23 Automatic 1 024 U 039 Automatic 2 040 U 055 Automatic 3 056 071 Automatic 4 072 U 087 Automatic 5 088 103 Automatic 6 104 119 Automatic 7 120 U 135 Automatic 8 136 U 151 Sound 1 152 167 Sound 2 168 U 183 Sound 3 184 199 Sound 4 200 215 Sound 5 216 231 Sound 6 232 247 Sound 7 248 U 255 Sound 8 048 055 10 Operating Mode Movement Macros 11 Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 16 of 27 7CH Channel Function Value Percent Setting 1 000 255 Oto 180 000 U 255 0 to 90 000 020 Stop 021 U 135 Clockwise rotation slow to fast 136 U 140 Stop 141 255 Counter clockwise rotation slow to fast 000 U 006 Open white 007 U 013 Yellow 014 U 020 Purple 021 U 027 Green 028 U 034 Red 035 U 041 Light Blue 042 U 048 Kelly Green 049 U 055 Orange 056 U 063 Dark Blue 064 U 070 White Yellow split colors 071 U 077 Yellow Purple split colors 078 U 084 Purple Green split colors 085 U 091 Green Red split colors 092 U 098 Red Blue split colors 099 U 105 Light Blue Kelly Green split colors 106 112 Kelly Green Orange split colors 113 119 Orange Dark Blue split colors 120 U 127 Dark Blue White split colors 128 U 191 Rotate counter clockwise slow to fast 192 U 127 Rotate clockwise slow to fast 000 U 003 Closed 004 U 007 Open 008
9. 5 048 U 055 Gobo 6 7 Gobo Wheel 056 U 063 Gobo 7 064 U 071 Gobo 7 shake fast to slow 072 079 Gobo 6 shake fast to slow 080 087 Gobo 5 shake fast to slow 088 095 Gobo 4 shake fast to slow 096 U 103 Gobo 3 shake fast to slow 104 111 Gobo 2 glass shake fast to slow 112 119 Gobo 1 glass shake fast to slow 120 127 Open 128 191 Gobo scroll counter clockwise rotation 192 255 Gobo scroll clockwise rotation 000 U 063 Gobo indexing l 064 147 Rotate clockwise slow to fast 8 Gobo Rotation gt 148 231 Rotate counter clockwise slow to fast 232 255 Gobo bounce 9 000 007 Prism 008 U 255 Stop static prism effect Prism Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 15 of 27 11 CH Channel Function Value Percent Setting 000 007 No function 008 015 Pan tilt move in black 016 023 Pan tilt move in black disable 024 U 031 Color wheel move in black 032 U 047 Gobo wheel move in black Color wheel and Gobo wheel move in black disable 056 U 063 Fast movement 064 U 087 Fast movement disable 088 U 095 All movement move in black disable 096 103 Reset pan tilt 104 111 No function 112 119 Reset color wheel 120 U 127 Reset gobo wheel 128 U 135 No function 136 U 143 Reset prism 144 U 151 Reset focus 152 159 Reset all 160 U 255 No function 000 U 007 No function 008 U 0
10. INTIMIDATOR SCAN 305 IRL INTIMIDATOR BARREL 305 IRC User Manual UE TABLE OF CONTENTS 1 Before YOU BEGIN pensen 0S EAn NEa 4 Ven e tele 4 WIT AC ING STS OR NR ER TET o PT 4 Qiu TR 4 RE E NETTE T EE 4 See 4 Bies Fag ec OBORA n neti niet TEE EIL TEE 4 Produc gt qe a RETE 5 SATO NOTE 5 AM Tat ge e e de gE 6 451 MH M HM O O Lc TH 6 WOMANS DIIS En 7 De DOCU o o 8 AC foc E pe 8 FUSE TREDIAC SINS gite e cM E 8 POW ML ador rere 9 POWER LINKING ele avira vise o er vele Dod uer aden a a LU PL DN ga t dle ht n 9 Mesleuigem erc EE 10 OE a ie EE 10 IGE P eeen EE 10 10 nM Ger SPS RN SPS M M a A 11 Control Panel RT dee E 11 Menmi Map WEE aa brenda aaa ds dobu O0 11 13 RK Tale Le feel 13 DMX ulis IR EE DO ETE 13 DMX Channel Assignments and Values 14 TAS Dl ete state aed ciet pud heet beraden ota att uta n OE O R etna 14 T i ny cre E O ee EE A 17 COniguration StandalOne 19 SOUNA 19 AWO MOO ER tesa ho bo i 19 viai Mode zaten eeen e M eee ee a 19 COnmiGuratlon Se WINGS
11. NU gt repeatedly until 4 icons show on the display Use UP or lt DOWNo gt to highlight Address Press ENTER and a number from 001 512 will show on the display Use UP or lt DOWN gt to change the number to the desired DMX starting address Press ENTER to select the DMX starting address The Intimidator Scan Barrel 305 IRC has 2 DMX personalities a 7 channel personality and an 11 channel personality To set the DMX personality do the following Press lt MENU gt repeatedly until 4 icons show on the display Use UP or lt DOWNS to highlight the Run Mode icon Press lt ENTER gt and the Run Mode options will show on the display Use UP or DOWN to highlight DMX Press ENTER A green dot will show on the DMX option line and the characters 7CH or 11CH will show in green 6 Use UP or DOWN to switch between 7CH and 11CH 7 Press ENTER to select the DMX personality shown a l gt ot um ou o s After the DMX starting address and personality have been set there will be a delay of 30 seconds before the display automatically returns to showing the current DMX address and the DMX personality Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 13 of 27 DMX Channel The following table outlines all the capabilities of the Intimidator Scan Barrel 305 IRC and Assignments and the channels that control them when the light is used with a lighting controller Values 11 CH Channel Fu
12. Sound Auto or IR to a DMX chain that includes a DMX controller Products in standalone mode can transmit DMX signals that interfere with the DMX signals from the controller oound mode sets the product to respond to sounds and music To set the product to Sound mode do the following 1 Make sure the product is connected to a power source and not connected to a DMX controller Press MENU repeatedly until 4 icons show on the display Use UP or DOWN to highlight the Run Mode icon Press ENTER and the Run Mode options will show on the display Use UP or lt DOWNS to highlight the Sound option Press ENTER A green dot will show on the Sound option line and the product will begin reacting to sound ol I B9 IM The product will respond only to low frequencies of music bass and drums If the product is not responding to sound increase the sensitivity For more information see the Sensitivity Setting below Auto mode sets the product to 1 of 16 preset movement patterns and color changes To set the product to Auto mode do the following 1 Make sure the product is connected to a power source and not connected to a DMX controller Press MENU repeatedly until 4 icons show on the display Use UP or DOWN to highlight the Run Mode icon Press ENTER and the Run Mode options will show on the display Use UP or DOWN to highlight the Auto option Press ENTER A green dot will show on the Auto op
13. acing each other and they both need to turn toward the same direction To reverse the pan movement do the following QUII UM ue I Press lt MENU gt repeatedly until 4 icons show on the display Use UP or DOWN to highlight the Setup icon Press ENTER The Setup options will show on the display Use UP or DOWN to highlight the Pan Reverse option Press ENTER The words ON or OFF will show in green Use UP or DOWN to switch between ON and OFF Press ENTER to select the setting Tilt Reverse Reversing the tilt movement is useful when 2 lights are facing each other and they need to point towards the same space between them To reverse the tilt movement do the following Press MENU repeatedly until 4 icons show on the display 1 Or She SED Use UP or lt DOWNS to highlight the Setup icon Press ENTER The Setup options will show on the display Use UP or lt DOWNS to highlight the Tilt Reverse option Press ENTER The words ON or OFF will show in green Use UP or DOWN to switch between ON and OFF Press ENTER to select the setting Screen Reverse The display can show the screen in two directions one for when the fixture is standing and one for when it is mounted upside down To set the display orientation do the following 1 Press MENU repeatedly until 4 icons show on the display 2 Use UP or DOWN to highlight the Setup icon DO OW N Press
14. e R Isenstadt 04 08 15 A Leon 05 08 15 Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 4 of 27 Product ata Glance Safety Notes A Use on Dimmer Outdoor Use Sound Activated DMX Master Slave Auto Programs Replaceable Fuse P Auto ranging Power Supply P p User Serviceable X These notes include important information about the mounting use and maintenance of this product Read these notes before using the product Always connect the product to a grounded circuit to avoid the risk of electrocution Make sure the power cord is not crimped or damaged Always disconnect the product from the power source before cleaning it or replacing the fuse Never disconnect the product from the power source by pulling or tugging on the cord If mounting the product overhead always secure it using a safety cable Make sure there are no flammable materials close to the product when it is operating Avoid direct eye exposure to the light source while the product is on Do not touch the product s housing when the product is operating because the housing can be very hot This product is not intended for permanent installation The product is for indoor use only It is rated at IP20 To prevent risk of fire or shock do not expose the product to rain or moisture Always make sure that the voltage of the power source to which the product is connected is within the range stated on the sticker or rear panel of the produc
15. gobo wheel rotation speed lt B gt Sets CG AUTO mode Colors and gobos will cycle automatically lt A gt Seis R T PAN TILT Press lt A gt to toggle PAN and TILT Use the lt gt and lt gt buttons to increase or decrease the selected value lt W gt Sets the prism value Use the lt gt and lt gt buttons to increase or decrease the prism value lt gt Increases values for controls as described above lt gt Decreases values for controls as described above lt 0 gt lt 9 gt Activates specific Auto modes Can be used as a shortcut for the combination of the lt AUTO gt button and the lt gt and lt gt buttons lt UV gt or lt P gt Has no function with this product D I OOOO OOODOOO OOOO 5 90000004 mg gg ee mg me m Z ek Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 22 of 27 Configuration Master Slave D Configuring the Slaves Configuring the Master Master Slave mode allows a single Intimidator Scan Barrel 305 IRC the master to control the actions of one or more Intimidator Scan Barrel 305 IRCs the slaves without a DMX controller In Master Slave mode the master is set to operate in Auto mode Sound mode or IR mode and the slaves are set to operate in Slave mode The master and slaves are daisy chained though the DMX input and output ports with the master at the beginning of the
16. ier immediately or failure to have all packaging available for inspection may invalidate your claim For other issues such as missing components or parts damage not related to shipping or concealed damage file a claim with Chauvet within 7 days of delivery For information on contacting Chauvet see the Contact Us section of this manual Text Convention Meaning Conventions 1 512 A range of values 50 60 A set of values Settings A menu option Menu gt Settings A sequence of menu options lt ENTER gt A button to be pressed ON A value to be entered or selected Sym bols Symbol Meaning AN Critical installation configuration or operation information Not following these instructions can make the product not work cause damage to the product or cause harm to the operator Important installation or configuration information The product might not function correctly if this information is not used Useful information JC Disclaimer he information and specifications contained in this User Manual are subject to change without notice Chauvet assumes no responsibility or liability for any errors or omissions and reserves the right to revise or recreate this manual at any time The latest version of this manual should be downloaded from http Awww chauvetlighting com product manuals literature Copyright 2015 Chauvet All rights reserved Electronically published by Chauvet in the United States of America Author Date Editor Dat
17. ing compressed air into them Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 24 of 27 6 TECHNICAL SPECIFICATIONS Dimensions and Weight Power Light Source Photo Optic Thermal DMX Ordering 16 9 in 480 mm Length Barrel Length Scan 18 9 in 480 mm Power Supply Type Switching internal Parameter Consumption Operating current Fuse Power UO Power input connector Power output connector Power cord plug Power linking current units Type LED Color White Parameter Illuminance 2 m Beam angle otrobe rate Pan Tilt Maximum External Temp 104 F 40 C VO Connectors 3 pin XLR Product Name Intimidator Scan 305 IRC Intimidator Barrel 305 IRC Intimidator Scan Barrel 305 IRC User Manual Rev 1 Width Scan 10 in 255 mm Width Barrel 10 in 255 mm Note Dimensions in inches are rounded to the nearest decimal digit Height Scan 5 7 in 147 mm Height Barrel 6 7 in 171 mm Range 100 to 240 VAC 50 60 Hz 120 V 60 Hz 104 W 1 5 A F 3 A 250 V US Canada IEC Edison US Edison US 13 6 A 5 units Power 60 W Quantity 1 Scan 9 110 lux 15 0 35 Hz 180 90 Cooling System Fan cooled Connector Type Sockets Item Code 08021029 08021047 Weight Scan 10 Ib 4 6 kg Weight Barrel 10 4 Ib 4 8 kg Voltage Selection Auto ranging 230 V 50 Hz 102 W 0 8 A F 3 A 250 V UK Worldwide IEC N A Local plug 13 6 A 10 units Lifes
18. ivity Resets the product Factory Set Loads factory defaults Ver VX X Running Mode XXXX Shows the current software version Sys Info running mode DMX address and DMX Address XXX product s temperature Temperature XXX Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 12 of 27 Configuration DMX DMX Starting Address DMX Personalities To set the product in DMX mode for control with a DMX controller do the following 1 Make sure the product is plugged into a power source 2 Connect the male end of a DMX cable to the DMX out socket of the DMX controller and the female end of the same cable to the DMX in socket on the product 3 Set the DMX starting address and personality by following the directions below When selecting a starting DMX address always consider the number of DMX channels needed for the selected DMX personality Choosing a starting address that is too high can restrict access to some of the product s channels The Intimidator Scan Barrel 305 IRC uses either 7 or 11 channels depending on the personality The highest configurable DMX address in 7 channel mode is 506 The highest configurable DMX address in 11 channel mode is 502 For more information about DMX download the Chauvet DMX Primer from the Chauvet web site http www chauvetlighting com download To set the DMX starting address do the following If the display shows a number from 001 512 go to step 5 Press lt ME
19. lt ENTER gt The Setup options will show on the display Use lt UP gt or lt DOWNS to highlight the Screen Reverse option Press lt ENTER gt The words ON or OFF will show in green Use UP or DOWN to switch between ON upside down display and OFF normal display Press ENTER to select the setting Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 20 of 27 Reset Resetting will restart the product It does not change any settings Resetting is a helpful troubleshooting tool and can be used if the product has stopped responding to control or if the control system has suffered a failure To reset the product do the following Press lt MENU gt repeatedly until 4 icons show on the display Use UP or lt DOWNS to highlight the Setup icon Press ENTER The Setup options will show on the display Use UP or lt DOWN gt to highlight the Reset option Press ENTER The product will immediately reset CN des m Reset to Factory Resetting to factory defaults will clear out all customized settings and return thee settings to the Defaults factory defaults Resetting to factory defaults can be used if the product is behaving inconsistently To reset the product to factory default settings do the following Press lt MENU gt repeatedly until 4 icons show on the display Use UP or DOWN to highlight the Setup icon Press ENTER The Setup options will show on the display Use UP
20. nction Value Percent Setting 1 000 U 255 0 180 000 U 255 0 90 000 U 020 Stop 021 U 135 Clockwise rotation slow to fast 136 140 Stop 141 U 255 Counter clockwise rotation slow to fast 000 U 255 Fast to slow 000 U 006 Open white 007 U 013 Yellow 014 020 Purple 021 U 027 Green 028 U 034 Red 035 U 041 Light Blue 042 U 048 Kelly Green 049 U 055 Orange 056 U 063 Dark Blue 064 U 070 White Yellow split colors 071 U 077 Yellow Purple split colors 078 U 084 Purple Green split colors 085 U 091 Green Red split colors 092 U 098 Red Blue split colors 099 U 105 Light Blue Kelly Green split colors 106 112 Kelly Green Orange split colors 113 119 Orange Dark Blue split colors 120 U 127 Dark Blue White split colors 128 U 191 Rotate counter clockwise slow to fast 192 U 255 Rotate clockwise slow to fast 000 U 003 Closed 004 U 007 Open 008 U 076 Synchronized Strobe slow to fast 077 U 145 Pulse Strobe slow to fast 146 U 215 Random Strobe slow to fast 216 255 Open Tilt Scan Tilt Barrel 3 Pan Tilt Speed 4 Color 5 Shutter Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 14 of 27 11 CH Channel Function Value Percent Setting 6 Dimmer 000 U 255 0 to 100 000 007 Open 008 U 015 Gobo 1 glass 016 023 Gobo 2 glass 024 U 031 Gobo 3 032 U 039 Gobo 4 040 U 047 Gobo
21. nical Support Email uktech chauvetlighting com World Wide Web www chauvetlighting co uk Technical Support Email servicio chauvet com mx World Wide Web www chauvet com mx Technical Support Email Eutech chauvetlighting eu World Wide Web www chauvetlighting eu Outside the U S United Kingdom Ireland Mexico or Benelux contact your dealer Follow their instructions to request support or to return a product Visit our website for contact details Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 27 of 27
22. pan 50 000 hours Current 2 3A Barrel 1 630 lux per beam 12 0 35 Hz 180 360 continuous Channel Range 7 or 11 UPC Number 781462213770 781462213954 RoHS Page 25 of 27 RETURNS In case you need to get support or return a product If you are located in the U S contact Chauvet World Headquarters If you are located in the UK or Ireland contact Chauvet Europe Ltd If you are located in Mexico contact Chauvet Mexico If you are located in Benelux contact Chauvet Europe BVBA If you are located in any other country DO NOT contact Chauvet Instead contact your local distributor See www chauvetlighting com for distributors outside the U S UK Ireland Mexico or Benelux If you are located outside the U S UK Ireland Mexico or Benelux contact your distributor of record and follow their instructions on how to return Chauvet products to them Visit our website www chauvetlighting com for contact details Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization RMA number before shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return Send the merchandise prepaid in its original box and with its original packing and accessories Chauvet will not issue call tags Clearly label the package with the RMA number Chauvet will refuse any product returned without an RMA number _ Write the RMA number
23. set the operating mode and the configuration settings of the D ae product Use the 4 buttons underneath the LCD display to access the control panel and escription navigate the menu map For specific instructions see the Configurations sections below Button Function lt MENU gt Enters into or backs out of the current menu option lt UP gt Scrolls up the list of options or selects a higher value lt DOWN gt Scrolls down the list of options or selects a lower value lt ENTER gt Activates a selected menu or value Menu Map The Menu Map presents all the options in the menu system and the values to set them Menu Value Description Address 001 512 Sets the DMX starting address DMX 24 Sets DMX personality Sets Slave mode Sond J oets Sound mode Sets infrared control Pan 0 to 180 0 to 90 Pan Tilt soeed fast to slow Run Mode Selects color options Sets dimmer value Strobe effect with increasing speed Manual 000 255 selects Gobo options Gobo Rotation effect with increasing Rotate speed Selects 3 facet prism Special Function Selects control functions P T Macro Selects pan tilt movement macros Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 11 of 27 Menu Value Description Normal pan operation Pan Reverse Reverse pan operation Normal tilt operation Tilt Reverse Reverse tilt operation Setup Screen Normal display Reverse Upside down display Sensitivity 001 100 sets sound sensit
24. t Never connect the product to a dimmer or rheostat Make sure to replace the fuse with another of the same type and rating Always install the product in a location with adequate ventilation and leave at least 20 in 50 cm between the product and adjacent surfaces Always use the handles to carry this product The maximum ambient temperature Ta in which the product can be used is 104 F 40 C Do not operate the product at higher temperatures Be sure that no ventilation slots on the product s housing are blocked Never carry the product by the power cord or any moving part In the event of a serious operating problem stop using the product immediately Never try to repair the product Repairs carried out by unskilled people can lead to damage or malfunction Contact the nearest authorized technical assistance center To eliminate wear and improve its lifespan during periods of non use completely disconnect from power via breaker or by unplugging it Keep this User Manual for future reference If you sell the product to another user be sure to give this manual to the next owner Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 5 of 27 2 INTRODUCTION Overview Safety Cable Pass Through Fuse Holder DMX In Out Power In Power Out Back Panel View Mirror d Adjustable T Lens E Lun Display p JL IR Senso LED Indicator LJ Menu Buttons Front View Scan Front Vie
25. t any of the Standalone modes as described in Configuration Standalone Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 23 of 27 5 TECHNICAL INFORMATION Product Dust build up on the lens reduces light output Dust build up on the body and fans can Maintenance cause overheating and mechanical wear which can reduce the usable life of the product To maintain optimum performance and minimal wear in a normal environment clean the product at least twice a month If the environment is particularly dusty clean the product more often For best results follow the suggestions listed below 1 2 3 Never clean the product when it is plugged into a power source Only clean the product when it is at room temperature Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external surfaces and in the vents Use a mild soap solution ammonia free glass cleaner or isopropyl alcohol to clean all the external optics and glass or transparent surfaces Apply the cleaning solution directly to a soft lint free cotton cloth or a lens cleaning tissue Gently wipe dirt and grime to the outside edges of the external optics and glass or transparent surfaces Gently polish the external optics and glass or transparent surfaces until they are free of haze and lint them i Always dry the external optics and glass transparent surfaces carefully after cleaning Do not spin the cooling fans while blow
26. tion line and the product will begin moving and emitting light O Ve GOE Manual mode allows the user to control every function of the Intimidator Scan Barrel 305 IRC through the LCD display To run the product in Manual mode follow the instructions below 1 Make sure the product is connected to a power source and not connected to a DMX controller Press MENU repeatedly until 4 icons show on the display Use UP or DOWN to highlight the Run Mode icon Press ENTER and the Run Mode options will show on the display Use UP or lt DOWNS to highlight the Manual option Press ENTER and the Manual options will show on the display Use UP or DOWN to select Pan Tilt P T Speed Color Dimmer Shutter Gobo Gobo Rotate Prism Special Function or P T Macro 8 Press ENTER and the current value 000 255 of the selected function will be highlighted 9 Use UP or lt DOWN gt to increase or decrease the value of the selected function 10 Press ENTER 11 Repeat steps 7 10 until the product is set as desired eee 19 I9 Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 19 of 27 Configuration The Intimidator Scan Barrel 305 IRC can be customized with settings such as pan direction Setti screen orientation and sound sensitivity Below are instructions for configuring all the settings ettings available Pan Reverse Reversing the pan movement is useful when 2 lights are f
27. w Barrel Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 6 of 27 Dimensions Di Barrel Scan Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 7 of 27 3 SETUP AC Power he Intimidator Scan Barrel 305 IRC have auto ranging power supplies that work with an A Fuse Replacement Intimidator Scan Barrel 305 IRC User Manual Rev 1 input voltage range of 100 to 240 VAC 50 60 Hz To determine the product s power requirements circuit breaker power outlet and wiring use the values listed on the label affixed to the product s back panel or refer to the product s Specifications The listed current rating indicates the products average current draw under normal conditions The Intimidator Scan Barrel 305 IRC can be power linked via the IEC and Edison outlets in its base Always connect the product to a protected circuit circuit breaker or fuse Make sure circuit has an appropriate electrical ground to avoid the risk of electrocution or fire Never connect the product to a rheostat variable resistor or dimmer even if the rheostat or dimmer serves only as a 0 to 100 switch To eliminate wear and improve its lifespan during periods of non use completely disconnect from power via breaker or by unplugging it Make sure product is not connected to a power source Oe ee eS Place the tip of a flat head screwdriver into the slot in the fuse holder Turn the scre
28. wdriver counterclockwise and the fuse holder will come loose Pull the fuse holder out of the product Pull the blown fuse out of the fuse holder Place a new fuse of the exact same type and rating into the fuse holder Insert the fuse holder into the product Place the tip of a flat head screwdriver into the slot in the fuse holder Turn the screwdriver clockwise and the fuse holder will tighten into place Disconnect the product from power before replacing the fuse Use only the fuse listed in the Technical Specifications section or on the specifications sticker on the product A spare fuse is not included Page 8 of 27 Power Linking The product provides power linking via the Edison IEC outlet located in the back of the unit Power Linking Diagram l Product ane Product gie Product Additional Products Up to 5 Intimidator Scan Barrel 305 IRC units can be linked on 120 V or up to 12 Intimidator Scan Barrel 305 IRC units on 230 V The power linking diagram shown above corresponds to the North American version i of the product ONLY If using this product anywhere other than North America consult with the local Chauvet distributor because power linking connectors and requirements differ from country to country and region to region Intimidator Scan Barrel 305 IRC User Manual Rev 1 Page 9 of 27 Rigging Diagram Mounting xis mounting the product read and follow the safety
Download Pdf Manuals
Related Search