Installation and User manual – DRCP
Contents
1. FAA aeaee 21 6 6 6 SVEO eT E 22 6 6 7 a C ON aera E 22 Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx Q eleckroiinvent 2 22 Copyright ELECTROINVENT Q electrolnyenk 1 Safety information The present manual contains important instructions for safety operation start running into exploitation and operation with complete units type DRCP This manual has to be kept together or near the equipment any time Used symbols and warning signs A DANGER means risky situation which if it is not avoided can lead to death or to serious injury ATTENTION ATTENTION refers to cases which are not connected with human injury Not conforming to this warning sign can bring to material damages 1 1 Warnings for danger and attention A Read and understand the manual and this installation guide before installing or operating the DRCP Installation exploitation and maintenance of the unit must be performed only by qualified personnel A Regional standards for installation must be observed AN DO NOT connect the DRCP unit to the drive if for some reason the cover of the drive system is removed N DO NOT open the cover of the DRCP units A If some information is not clear please contact with the service center of your distributor Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 3 22 Copyright ELECTROINVENT Q eleekroimve A ATTENTION Warrant2. Function task When you enter the Set Function task the following items appear on the Panel display the Function Name is displayed starting at the left end of the lower Display line the State inscription is displayed to the right of the Drive Status Area on the upper Display line the present Function State 0 or 1 is displayed immediately after the State inscription on the upper Display line the action that can be taken in relation with the displayed function SET or CLR is shown at the right end of the lower Display line The example below shows the Emergency Stop function which is available on most Drive Unit systems SET blinking Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 19 22 Copyright ELECTROINVENT Q electrolnye A The present function state is 0 inactive so the available action to take is activation SET as shown in the right end of the lower Display line The action to take hint appears blinking The available function action SET in this case can be applied by pressing Data Enter Thus the Emergency Stop virtual input is activated and the Drive Unit goes from ready Rdy to disabled Off state The changed Display appearance after Emergency Stop activation by pressing Data Enter is shown below LITT Mer af CLR blinking As seen the new function state is 1 active so the available action to take is de activation CLR Now
3. UP v DOWN and DATA ENTER keys you can browse through the hidden parameters modify them and store the modified values in the way described for ordinary parameters in 6 4 and 6 5 section However doing modifications is not recommended unless they have been suggested by the Drive Unit manufacturer To exit Hidden Param task and return to SPECIAL TASKS state at any moment press ESC Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 21 22 Copyright ELECTROINVENT Q eleeckrolAveant 6 6 6 Save Config When Save Config task is started the Control Panel downloads the entire configuration from the Drive Unit and stores it in the non volatile memory Then the Panel returns to the MAIN operation state 6 6 7 Send Config When Send Config task is started the Control Panel uploads the stored configuration to the Drive Unit and then the Panel returns to the MAIN operation state ATTENTION The stored configuration keeps information about the type of the Drive Unit from which it s been obtained Before sending the stored configuration the Panel checks if this type is the same as the type of the presently connected Drive Unit If the types do not match the following message is displayed for a while Then the Panel returns to the MAIN operation state Contacts Q electroinvent Tel 359 2 862 14 06 868 70 65 43 Cherni Vrah blvd Fax 359 2 962 52 63 1407 Sofia PO Box 74 E Mail office elin
4. screens within this task that can be browsed using the UP and v DOWN keys The upper Display line of any screen contains the Drive Unit identification SPCS4 400 in the example below The lower lines on the 1 st and 2 nd screens show the hardware and software identifiers of the Drive Unit The lower line on the 3 rd screen shows the Control Panel software revision To exit Product Info task and return to SPECIAL TASKS state at any moment press ESC 6 6 5 Hidden Param Hidden Parameters are a special set of Drive Unit configuration entries which are not part of the usual Menu Parameter layout Typically factory settings of the hidden parameters don t need further modification so these parameters are kept aside and they are also protected by a highest access level password There is no Menu Letter corresponding to the Hidden Parameters menu as there is for any explicit parameters menu so the identifier for any hidden parameter contains the character instead of menu letter In all other respects Hidden Parameters are like the ordinary parameters they can be freely observed and they can be changed provided that the needed access level has been granted to the operator Please refer to 4 3 and 4 4 section for details about parameter name value presentation on the Panel Display The example below shows the Vtg Gain hidden parameter used for scaling of the DC link voltage feedback channel Using the
5. tasks might use parts of the display area differently Display areas allocation for these special cases is described separately Only the Drive Status area assignment is completely invariable regardless of present Panel task so the Drive Status information is always present on the Panel display 4 1 The Drive Status area Drive Unit status is shown in the upper left corner of the Panel Display Status inscription stays there all the time after Panel lt gt Drive communication is established Normally drive resides in one of the two stable states Rdy ready not operating or Run operating Other normal states are transient Ini Initializing CLd Capacitors Loading Exc Excitation Dex Deexcitation etc Most transient states are quite short lived and are not monitored If some of the Drive fault protections are active the Drive goes to Fault state In that case the Status area displays the active fault inscription OSF over voltage USF under voltage SC short circuit OC over current etc Fault inscriptions are shown blinking so they are distinctly noticeable Examples USF blinking 4 2 The Menu ldentification area Drive configuration parameters are grouped in Configuration Menus Menus are denoted by single lower case Latin letters The Menu Letter uniquely identifies every Drive Configuration Menu So the Menu Letter is also a Menu Identifier Additionally menus are depicted by Menu Names
6. usage is provided here More details will be given in further sections in relation with the specific Panel tasks 5 2 Up and Down buttons The 4 UP and v DOWN pair of buttons generally perform two different tasks depending on the Panel Operation State 5 2 1 Browsing Up Down through the Drive Configuration Menus Example Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 11 22 Copyright ELECTROINVENT Q eleekroinvent or Browsing Up Down through the Parameters within certain Configuration Menu Example 5 2 2 Increasing or Decreasing v a Configuration Parameter value when in Parameter Edit state Example 12 times 2 times Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 12 22 Copyright ELECTROINVENT Q eleekroimve A The parameters in menu dO are password protected You can only browse through the parameters but you cannot edit them To enter a password please refer to 6 6 Brief pressing of UP or v DOWN key increases decreases the edited value by a 1 This way of modification could take a lot of time and effort in case of big difference between the presently set and the desired value The process goes much faster if the 4 UP or v DOWN key is pressed and held for as long as needed While the key is being held the edited value starts slowly increasing or decreasing at small steps ones then the rate of change accelerates as the step be
7. CTROINVENT Q electrolnye Al 6 Control Panel Operation States The set of Control Panel tasks that can be accomplished at any given moment is determined by the Panel Operation state The functions of the Panel Keypad buttons and the information shown on the LCD display are also determined by the Panel Operation state Control Panel Operation States are outlined in the diagram below Keypad actions and transitions between Operation States are also depicted there PoOower Up Or Cable Connection CONNECTING SPECIAL TASKS Hidden Parcan Save Contig Send Config SET PARAMETER VALUE 6 1 The CONNECTING State This is the first state after Panel and Drive Unit are interconnected through the communication cable as depicted in section 3 While trying to establish communication with the Drive Unit the Panel cannot implement any other task Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 16 22 Copyright ELECTROINVENT Q eleekrolavent 6 2 The MAIN State After communication with the Drive is established the Panel enters MAIN state Only Drive Status is displayed in this state refer to section 4 1 From MAIN state the panel can go either to BROWSE MENUS or to SPECIAL TASKS state to enter BROWSE MENUS state press any of the UP v DOWN or Data Enter keys to enter SPECIAL TASKS state press and hold ESC key then without releasing it press Data Enter key 6 3 The BROWS
8. Copyright ELECTROINVENT Q eleetrolmve A DRIVE REMOTE CONTROL PANEL Type DRCP User Manual March 2015 Drive Remote Control Panel_ User_manual Rev 00 Electroinvent docx Copyright ELECTROINVENT A G N Contents Safety Informatii mesis invrnasiniona e air a aa ian i 3 1 1 Warnings for danger and attentiOn ccccccseseceeessseeseeeeeeeeeeeeeseeaeeeeeeeeas 3 Wa AN e E 4 IONE OCU COIN oc E E 5 Connecting the Control Panel ccccccsssssseeeeeeeeeeeceessneeeeeeeeeoeessseeeeesseooenens 6 Allocation of Control Panel display areas ssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 9 4 1 The Drive Status area ccccccccccssceceeececeeeeeseeeeseeeeseueesseeeesseeeseeeeesegeeees 9 4 2 The Menu Identification area ccccccccccsscccccessceeceeseceeceeeeeseeeeeesseeeessaaes 9 4 3 The Parameter Identification area cccccccccsecccceeceeceeeeeeeeeesseeeeseeeeesaeees 10 4 4 The Parameter Presently Set Value area eecccecceeeeeeeeeeeeeeeeeeeneneeeees 10 4 5 The Parameter Edit Value area cccccecccecsseeeeeeeeeeeesaeeeeeeeeeeeeeneaeeeesaees 10 Control Panel Keypad ugescecesecscee nce seme wensteeerveqerateesesniee sovsasuesuesdoosssatoveasuensadedaus 11 51 PAI ANG Stop DUWONS atc aes5cbocaccheeeepasoseayesseatessaseatennsseebgreascieeateeo as 11 5 2 Up and Down DuttONns eee ccccccseeeecceeceeeeeeeeeeeeeeceeeeeeeeeeeesseaeeeeeessaaeeeees 11 5 2 1 Browsing U
9. E MENUS State In BROWSE MENUS state the lower line of the LCD display shows the Menu letter and Menu name refer to section 4 2 The Menu Identification area You can exit the BROWSE MENUS state and return to the MAIN State by pressing ESC Or you can scroll through the menus of the Drive Unit configuration by pressing UP or v DOWN When the needed menu appears you can go inside it to look at its parameters by pressing Data Enter which brings you to the BROWSE PARAMETERS state 6 4 The BROWSE PARAMETERS State In BROWSE PARAMETERS state the lower line of the LCD display shows the Parameter identifier and Parameter name refer to section 4 3 The Parameter Identification area Besides the upper line of the LCD display exhibits the configured value of the shown parameter refer to section 4 4 The Parameter Presently Set Value area You can exit the BROWSE PARAMETERS state and return to the BROWSE MENUS state by pressing ESC Or you can scroll through the parameters of the selected menu by pressing UP or v DOWN When the needed parameter appears you can press Data Enter to go to EDIT PARAMETER state if you need to change the configured parameter value NOTE 1 Modification of some configuration parameters could be restricted to qualified personnel only so it might be password protected If the password needed for the parameter access level has not been provided in advance g
10. Example 4 5 The Parameter Edit Value area When Edit Parameter mode is entered the actual presently set parameter value is still shown in its area as described in section 4 4 But the Parameter Name area refer to section 4 3 is replaced by a Parameter Edit Value area On entering the Edit Parameter mode the Present Parameter Value and Parameter Edit Value are identical Then while modifying the Parameter Edit Value you can still observe the presently set parameter value above it The parameters in menu dO are password protected You can only browse through the parameters but you cannot edit them To enter a password please refer to section 5 6 Example Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 10 22 Copyright ELECTROINVENT Q eleekroimve A 5 Control Panel Keypad 5 1 Run and Stop buttons The Run and Stop button pair provides for Drive Unit Start Stop command independently of the Panel Operation State Panel Operation State definition is provided in section 6 Starting Stopping the Drive from the Control Panel is possible only if Drive I O is appropriately configured Drive Configuration setup is Drive Unit specific and goes beyond the scope of this Manual Please refer to the Configuration manual of the particular Drive Unit for details The functions of the other four Keypad buttons are dependent on Panel Operation State So just basic outline of the buttons
11. a new Data Enter pressing would perform the CLR action Emergency Stop input is de activated the Drive Unit returns to ready Rdy state and the Display restores its initial appearance To exit Set Function task and return to SPECIAL TASKS state press ESC 6 6 3 Faults Log Fault Log task provides for inspection of Fault Activations logged in the Drive Unit memory When the Fault Log task is entered the Fault 1 inscription appears on the lower Display line followed by the name of the 1 st newest fault logged Pressing UP or v DOWN allows browsing through all logged faults Pacii Over Voltage is the 2 nd logged Fault In the above example the first display appears when Fault Log task is entered by pressing DATA ENTER Then pressing UP exhibits the 2 nd logged fault Next UP pressing produces no result as there are not more faults logged Pressing v DOWN restores the Fault 1 display If no faults have been logged in the Drive Unit faults history the following display appears on entering the Fault Log task ee ji Ho P Suits ingen To exit Fault Log task and return to SPECIAL TASKS state at any moment press ESC Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 20 22 Copyright ELECTROINVENT Q eleekrolmve Al 6 6 4 Product Info The Product Info task provides information about both the Drive Unit and the Control Panel There are three
12. can retry entering the correct password or press ESC to exit the Set Password task and return to SPECIAL TASKS state NOTES 1 When you commence the Set Password task end press Data Enter the result of this operation overwrites any previous Access Level state For instance if you have been granted the highest Access Level 3 by entering the corresponding password and then you repeat the Set Password task and enter the password corresponding to a lower Access Level 1 then you lose the Access Level 3 permissions and acquire Access Level 1 ones If you have acquired some any Access Level rights and then repeat the Set Password task and enter an invalid password you lose your access permissions 2 Any Access Level permissions are automatically cancelled if no keypad activity has been observed for sufficiently long period of time 5 minutes is adopted as duration of this keypad idle interval 6 6 2 Set Function Various Digital Input Functions can be assigned to the Drive Unit multi functional digital inputs Reviewing the functions goes beyond the scope of this manual as they are Drive Unit specific The essential principle is that a Digital Input Function which is not assigned to any physical input on the Drive Unit Terminal Board may be provided via the serial communication port through the ConfigMaster PC software tool or via the Drive Remote Control Panel which is the object of the manual This is done through the Set
13. comes 10 further it keeps on accelerating as the step grows to 100 then 1000 Releasing the held button returns the modification step to the smallest value of 1 so if the edited parameter has gone beyond the desired value while the UP or v DOWN key has been held you just release the button for an instant then trim the value using a smaller increment 5 3 DATA ENTER button The DATA ENTER button is used for 5 3 1 Entering the present Configuration Menu Entering the present Configuration Menu shown in the Menu Identification area refer to section 4 2 Thus the Panel Operation State moves one level down refer to section 6 for Panel Operation States description Example Ki la o gF ad G erara EtL 5 3 2 Entering the Parameter Edit state for the Configuration Parameter Entering the Parameter Edit state for the Configuration Parameter shown in the Parameter Identification area refer to section 4 3 Thus the Panel Operation State moves one level down refer to section 6 for Control Panel Operation States description The parameters in menu dO are password protected You can only browse through the parameters but you cannot edit them To enter a password please refer to 6 6 Example Aid 228 CEI PSs Wig L Mop ck TES Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 13 22 Copyright ELECTROINVENT Q eleelkrolamve A 5 3 3 Accepting confirming the new value
14. for the Parameter Accepting confirming the new value for the Parameter when in Parameter Edit Operation State In this case the Parameter value from the Parameter Edit Value area refer to section 4 5 becomes the new actual Parameter value and appears in the Parameter Presently Set Value area refer to section 4 4 The parameters in menu dO are password protected You can only browse through the parameters but you cannot edit them To enter a password please refer to 6 6 Example pm at 2 2 Maaa Ja Pag e l a a H Hia anag fesse Suess so 10 times Mains Ung h In this example the second DATA ENTER pressing confirms parameter modification The modified parameter value 230 from the Edit area appears in the Presently Set Value area Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 14 22 Copyright ELECTROINVENT Q eleeckrolavent 5 4 ESC button The ESC button is used for moving returning to the upper level of the Panel Operation State refer to section 6 for Control Panel Operation States description The parameters in menu dO are password protected You can only browse through the parameters but you cannot edit them To enter a password please refer to 6 6 Example beii j AIENeEr al ae Tum Any modifications done in Parameter Edit state are canceled by pressing the ESC Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 15 22 Copyright ELE
15. fore or after applying power to the latter The 9 pin D sub connector on the Panel is connected to the RJ45 connector of the Drive via provided serial communication cable Please see the Fig 3 7 below Fig 3 1 Connecting the Control Panel to a Drive Unit in the picture above is shown example of connection with SPCS 4 400 When the cable is plugged at both ends and the Drive is powered the Panel commences auto tuning procedure to detect the Node Id and the communication parameters set in the Drive In the common case when the Node ld is set to 1 auto tuning lasts a couple of seconds For bigger Node Id values it may take longer approximately 4 5 seconds per node For instance if the Drive Node Id has been set to 10 the tuning would take about 45 seconds to complete During this procedure the Panel displays the tried connection parameters Example Trying Mode 12 When tuning is completed and connection with the Drive is established the Panel displays the Drive Status Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 6 22 Copyright ELECTROINVENT Q elecltrolnye Al The base version of Control Panel uses RS232 communication MODBUS RTU There is a possibility for optional RS485 communication For choosing RS232 or RS485 communication must be used the 4 position DIP switch next to the communication port of the panel On the base model of the Control Panel the DIP switch is properly factory set to RS232 a
16. ion permissions only to skilled personnel protects the drive unit from unreasonable configuration changes that may affect its correct operation There are 3 access levels used by the Drive Unit configuration management system Correspondingly there are 3 passwords defined one for each access level Passwords are given to the drive operating personnel according to its qualification and job characteristics When Set Password task is entered the Password inscription appears on the lower LCD line followed by the Password Entering Area containing the initial Password value 0 Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 18 22 Copyright ELECTROINVENT Q electrolnye Al Using the UP and v DOWN keys you modify this value to set the correct password and then press Data Enter to confirm it If the provided value is correct the Panel exits the Set Password task as well as the SPECIAL TASKS State and goes to BROWSE MENUS state from where you can navigate to the needed Menu and modify the needed Parameter using the acquired modification rights In case that the provided number password does not match any of the three access level passwords the value in the Password Entering Area is reset to zero and a Pls Retry message starts flashing on the upper display line Pacii Ris metrii scce ccce s e off e A e Pa we os PEGE GE OE GOS esse esse oa es a a m aes Then you
17. nd there is no need to change the positions of the DIP switch Please see Fig 3 2 DIP Switch a je Fig 3 2 Positions of the DIP switch The positions of the DIP switch must be as shown in the table below Table 3 1 Positions of the DIP switch oP Switch key number Rs RSS 1 Bown pestion OF Up poson 2 onoono OF Un positon 8 mp positon on Down poston on Down positon ATTENTION In the base model of the Control Panel is applicable only RS232 combination of the DIP switch Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 7 22 Copyright ELECTROINVENT Q eleekroimve A The label with serial number of the Drive Remote Control Panel is on the back of the device see Fig 3 3 Hon ce r r r t T v lt Pes ee i r ne Aad PE hl a uF y te ge 4 Wag 90 Pi i Fig 3 3 Label with serial number The dimensions of DRCP device are shown on Fig 3 4 94 mm 26 mm 162 mm Fig 3 4 Dimensions of DRCP device Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 8 22 Copyright ELECTROINVENT Q eleekroimve A 4 Allocation of Control Panel display areas The Panel Display is 2 x 16 2 lines x 16 characters Display space allocation is described below Note display area allocation scheme depicted here concerns the most common Control Panel tasks browsing through menus and parameters and modifying parameter values Other Panel
18. oing to EDIT PARAMETER by pressing Data Enter will not be possible NOTE 2 Browsing the parameters of Menu b the Display menu represents a particular case When Menu b is entered scrolling up or down the parameters by the UP or v DOWN keys selects internal drive variables for continuous monitoring As an example three different values of Menu b parameters shown below enable continuous monitoring of the DC link voltage in V bO selected the drive unit phase current in A b1 selected the drive unit output frequency in Hz b3 selected Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 17 22 Copyright ELECTROINVENT Q eleekrolimve Al Generally correspondence between the Menu b parameter values and the monitored variables is Drive Unit dependent but the selections in this example are common and valid for all Drive Unit types 6 5 The EDIT PARAMETER State In EDIT PARAMETER state the lower line of the LCD display contains the Parameter Identifier and the Parameter Edit Area refer to section 4 3 The Parameter Identification area and section 4 5 The Parameter Edit Value area Besides the upper line of the LCD display still exhibits the configured value of the shown parameter refer to 2 4 The Parameter Presently Set Value area You can increase or decrease the configured parameter value using UP or v DOWN keys The value in the Parameter Edit Area changes re
19. p Down through the Drive Configuration Menus 11 5 2 2 Increasing or Decreasing v a Configuration Parameter value when in Parameter Edit state cccceseceeeeeeeeeeeeeeeeees 12 53 DATAS ENTER DUTTON cdsnnsiscntcudssntemtevactiadinwadsadssvmadentsnndeaussinntsosanadeauhaensends 13 5 3 1 Entering the present Configuration Menu ccccsseeeeeeeees 13 5 3 2 Entering the Parameter Edit state for the Configuration PEIO eee nee ene eee ee 13 5 3 0 Accepting confirming the new value for the Parameter 14 wA ESC DUN ON eennee ee oe eee eee eer eee ee aan 15 Control Panel Operation States ccccccssssssseeeeeeeeeeeceesneeeeeeeseeeeeseseeeeeseeees 16 6 1 ThE CONNECTING Slate isiiccsvascesinsnassuyduussvesdsnawestinasesnavansqacsubestseusannaansdaes 16 62 The MAIN Stale aaa cree cnressusterenicectesten sestenars ch visa ANETE NOKTAN KARANANE EKEN ENEAN TREE 17 63 The BROWSE MENUS State voce siccscccteacicersdcelecnntocdeacssaesccsbindsiaxsdgeiiaesiendes 17 6 4 The BROWSE PARAMETERS State cccceccceeeeeeeeeeeeeeeeeeeeeeeeseeees 17 65 The EDIT PARAMETER Stale anne Pn ee ee ee 18 66 The SPECIAL TASKS State ene en ee ee 18 6 6 1 PG F OWO a sat acs biaevheneacdce vee wenger 18 6 6 2 O FUNCION sur arn a aienebaseetnees aseooateeeecoeat ees 19 6 6 3 FAU E e yanshed eietosatnianes betensodertaata nen 20 6 6 4 POUCES aeenoaceexeroese ese 21 6 6 5 POEN
20. spectively but the configured value displayed on the upper line stays unaltered until you press Data Enter Pressing Data Enter confirms the modified value and it appears in the upper line as a new Presently Set Value While any parameter value modification is not confirmed through Data Enter you can cancel it by pressing the ESC key which brings you back to BROWSE PARAMETERS state Pressing Data Enter also returns the Panel to BROWSE PARAMETERS state but with parameter modification accepted Please see also section 5 2 2 for additional details and tips concerning usage of and v keys for parameter value editing 6 6 The SPECIAL TASKS State As described in 6 2 the SPECIAL TASKS state is entered from MAIN state by pressing first ESC then Data Enter keys and holding them pressed together for an instant From the SPECIAL TASKS state you have a choice of various tasks related to Drive Unit monitoring control Browsing through the available tasks is done by pressing UP or v DOWN task names appear in the lower LCD display line To start the needed task you press Data Enter To exit SPECIAL TASKS state and go back to MAIN state you press ESC 6 6 1 Set Password As described in the note 1 in section 6 4 providing a password may be needed in order to obtain permission to modify some parameters that require higher access level Restricting access to some parameters and granting modificat
21. such as General Setup Current Limit Communication etc When browsing through the configuration menus the Menu Identifier followed by the Menu Name occupy the entire 2 lower display line Example Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx Copyright ELECTROINVENT Q eleekrolmve Al 4 3 The Parameter Identification area Parameters within a menu are denoted by an index parameter number A Menu Letter Parameter Index pair such as a1 or e11 uniquely identifies every Drive configuration parameter So the Menu Letter Parameter Index pair is also a Parameter Identifier Additionally parameters are depicted by parameter names like Mains Vig V flnvert kHz Node ID etc When browsing through the parameters within any configuration menu the Parameter Identifier followed by the Parameter Name occupy the entire ane lower display line Example 4 4 The Parameter Presently Set Value area While browsing through the parameters within any configuration menu you can look over parameter values that are currently set in the Drive configuration Currently set parameter values are displayed to the right of the Drive Status area refer to section 4 1 So as described in section 4 3 during parameter browsing you observe the Parameter ldentifier Parameter Name on the bottom display line and you monitor the present Parameter Value on the top display line above the Parameter name
22. vent com Bulgaria Web site http www electroinvent com Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 22 22
23. y void The unit must not be damaged as well as it is forbidden to make holes on it Any transport damage has to be established and reported to supplier before unit installation 1 2 Warranty The data and installation instructions given in this guide are revised regularly and all corrections are included in next issues In case of avoiding the installation instructions the warranty claims will not be accepted We cannot bear any responsibility also in cases of incidents and material damages due to improper use as well as from actions of not authorized persons with resulting from these consequences Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 4 22 Copyright ELECTROINVENT Q electrolnye Ale 2 Introduction Drive Remote Control Panel DRCP device is intended for monitoring and adjustment of different type drive systems It implements user friendly plug amp play design for quick connection and service activities DRCP is a compact pocket size and lightweight device which eliminates the need for a PC or laptop You can easily connect with the drive to adjust and monitor different parameters or maintain the drive system This device is with class of protection degree IP20 Drive Remote Control Panel_User_manual Rev 00 Electroinvent docx 5 22 Copyright ELECTROINVENT Q eleekroliave A 3 Connecting the Control Panel Connection of the Control Panel The Panel to the Drive Unit The Drive can be done either be
Download Pdf Manuals
Related Search