Krystal Clear™ Model 633T Filter Pump
Contents
1. 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English 109 IMPORTANT SAFETY RULES Read understand and follow all instructions carefully before installing and using this product Krystal Clear Model 633T Filter Pump For illustrative purposes only JUNTEX IMPORTANT DO NOT RETURN PRODUCT TO STORE To purchase parts and accessories or to obtain non technical assistance Visit TAWA For technical assistance and missing parts call us toll free for U S and Canadian Residents 1 800 234 6839 Monday through Friday 8 30am to 5 00pm Pacific Time 109 R0 1406 109 MODEL 633T FILTER PUMP ENGLISH 7 5 10 3 PANTONE 295U 06 21 2013 English TABLE OF CONTENTS Warnings Parts Reference Setup Instructions Operating Instructions Operating Time Table Pool Care and Chemicals Long Term Storage Troubleshooting Guide Common Pool Problems General Aquatic Safety Limited Warranty SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English IMPORTANT SAFETY RULES READ AND FOLLOW ALL INSTRUCTIONS A WARNING To reduce the risk of injury do not permit children to use this product Always supervise children and those with disabilities Children must stay away from this product and electrical cord s Assembly and disassembly by adults only Risk of electric shock Connect only to2. MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English TROUBLESHOOTING GUIDE DOM AB AAYE R OOeAR UU A 3 TROUBLE CAUSE SOLUTION FILTER MOTOR The motor is not plugged in Filter cord must be plugged into a 3 wire FAILS TO START The GFCI circuit breaker outlet that is protected by a Class A is tripped Ground Fault Circuit Interrupter Motor too hot and overload Reset circuit breaker If circuit breaker trips protection shut motor off repeatedly your electrical system may have a defect Turn off circuit breaker and call an electrician to correct the problem Let motor cool down FILTER DOESN T Improper chlorine or pH levels Adjust the chlorine and pH level Consult your local CLEAN POOL Filter cartridge is dirty swimming pool supply stores Damaged cartridge Clean or replace cartridge Excessively dirty pool Check the cartridge for holes Replace if damaged The strainer screen is restricting Operate the filter for longer periods the water flow Clean the strainer screen at the inlet FILTER DOESN T Clogged inlet or discharge Clear any obstructions in the intake hose by PUMP WATER OR An air leak on the intake line discharging it inside pool wall THE WATER FLOW IS Scale or buildup on cartridge Tighten hose nuts check hoses for damage check VERY SLOW Excessively dirty pool pool water level Dirty filter cartridge Clean cartridge more of
3. a grounding type receptacle this product is provided with a ground fault circuit interrupter If replacement of the plug or cord is needed use only identical replacement parts Always unplug this product from the electrical outlet before removing cleaning servicing or making any adjustment to the product The unit is provided with a ground fault circuit interrupter GFCI To test the GFCI push the test button The GFCI should interrupt power Push the reset button power should be restored If the GFCI fails to operate in this manner The GFCI is defective If the GFCI interrupts power to the pump without the test button being pushed a ground current is flowing indicating the possibility of an electric shock Do not use this pump Disconnect the pump and have the problem corrected by a qualified service representative before using Do not bury the electrical cord Locate the cord where it will not be damaged by lawn mowers hedge trimmers and other equipment To reduce the risk of electric shock replace damaged cord immediately Use a qualified electrician to replace the cord To reduce the risk of electric shock do not use extension cords timers plug adaptors or converter plugs to connect unit to electric supply provide a properly located outlet Do not attempt to plug in or unplug this product while standing in water or when your hands are wet Do not use an appliance leakage current interrupter ALCI in place of a GFCI
4. since the ALCI will not protect people Position this product away from pool so as to prevent children from climbing on it and access the pool Do not operate this product when pool is occupied This product is intended to be used only for the purposes described in the manual FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE ELECTRIC SHOCK ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH CAUTION This product is for use with storable pools only Do not use with permanently installed pools A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage These product warnings instructions and safety rules provided with the product represent some common risks of water recreation devices and do not cover all instances of risk and danger Please use common sense and good judgement when enjoying any water activity SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English PARTS REFERENCE Before assembling your product please take a few minutes to check the contents and become familiar with all the parts pui KO F w NOTE Drawings for illustration purpose only Actual product may vary Not to scale REF NO DESCRIPTI
5. to prevent suction entrapment The vacuum release valve will reset once the blockage is removed and the pump is switched off To restart the system the air must be removed from the filter pump per previous step To operate the filter pump on TIMER mode A Set the timer dial to the desired operating hours See operation time table See Fig 10 B Turn on the pump by pressing the switch to position the filter pump is now filtering the water and will stop after the operating hours are completed The built in timer will now operate for the number of hours selected at the same time each day C Operating hours can be re adjusted if necessary Follow step A B To operate the filter pump manually without the TIMER mode A Turn on the pump by pressing the switch to I position the filter pump is now filtering the water B To turn off the pump press the switch to O position P ea il P SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 10 3 PANTONE 295U 06 21 2013 English OPERATING TIME TABLE This table shows the required operating time for average use of the filter pump with AGP s The filter pump running time should be 1 hour longer than the required operating time of the Saltwater System Water Capacity Calculated at 90 for Frame Recommend Pool Size Pool and 80 for Easy Set amp Oval Pool Gals Liters Hours INTEX ABO
6. water from flowing out of the pool Gently turn the top air release valve once or twice in a counter clockwise direction The housing cover can now be easily removed In a counter clockwise direction remove the filter housing collar 1 Place it in a safe location Remove the housing cover 4 Now remove the used filter cartridge SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English CLEANING OR REPLACING FILTER CARTRIDGES continued Examine the inside of the filter housing If dirt or sediment is located on the bottom of the housing then A In a counter clockwise motion gently unscrew and remove the sediment valve 2 located at the bottom of the housing Place it in a safe place B With a bucket of water or a garden hose pour water into the housing flushing out the sediment C Screw back the sediment valve 2 in a gentle clockwise motion Do not over tighten Place a new cartridge filter in the housing Return the housing cover 4 to its position and in a clockwise direction rescrew the housing collar 1 onto the filter housing Turn both plunger valve handles fully counter clockwise until they stop This opens the valve allowing water to flow into the filter pump When the trapped air has escaped through the air release valve gently retighten the valve 2 in a clockwise direction Reconnect the power cord Turn on the pump LONG TERM STORAGE Befor
7. ND IN NO EVENT SHALL INTEX THEIR AUTHORIZED AGENTS OR EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL DAMAGES OR LIABILITIES Some states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This Limited Warranty does not apply if the products are subject to negligence abnormal use or operation accident improper operation improper voltage or current contrary to operating instructions or to damage by circumstances beyond Intex s control including but not limited to ordinary wear and tear and damage caused by exposure to fire flood freezing rain or other external environmental forces This Limited Warranty applies only to those parts and components sold by Intex The Limited Warranty does not cover unauthorized alterations repairs or disassembly by anyone other than Intex Service Center personnel DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN OR REPLACEMENT IF YOU ARE MISSING PARTS OR NEED ASSISTANCE PLEASE CALL US tA pede OR Ire U S AND CANADIAN RESIDENTS 1 800 234 6839 OR VISIT OUR WEBSITE WWW INTEXSTORE COM Proof of Purchase must accompany all returns or the warranty claim will be invalid SAVE THESE INSTRUCTIONS
8. ON QTY SPARE PART NO THREADED FILTER HOUSING COLLAR AIR RELEASE VALVE SEDIMENT RELEASE VALV VALVE O RING 4 19 5 FILTER Housing O RING Jif ma 6 FILTER CARTRIDGE 59905 8 j PUMPHOSEWTHNUTS 1 1 2 1mo When ordering parts be sure to quote the model number and part numbers SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English PARTS REFERENCE continued Before assembling your product please take a few minutes to check the contents and become familiar with all the parts REF NO DESCRIPTION PART v rosorna o 1 O 15 ADJUSTABLE POOL INLET Nozze 1 smawmomo Ooo y Optional When ordering parts be sure to quote the model number and part numbers SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 10 3 PANTONE 295U 06 21 2013 English POOL OUTLET STRAINER amp PLUNGER VALVE SETUP optional The strainer grid prevents large objects from jamming and or damaging the filter pump The plunger valve assembly prevents water from flowing into the filter pump while the filter cartridge is being placed or cleaned If your pool has inflatable top ring install the strainer nozzle and plunger valve before inflating the pool liner top ring The parts numbers here o
9. OT TO SCALE SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English OPERATING INSTRUCTIONS Make sure the filter pump is switched off The switch is located on the motor housing Connect the power cord to a GFCI protected electrical outlet A WARNING Risk of electric shock Connect this product only to a grounding type receptacle protected by a ground fault circuit interrupter GFCI Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI IMPORTANT To prevent air lock open the lower plunger valve connected inlet hose first and then the upper plunger valve connected outlet hose Open the air release valve wait until water starts to flow out of the air release valve close air release valve Turn both plunger valve handles fully counter clockwise until they stop This opens the valve allowing water to flow into the filter pump With water flowing into filter pump the water pressure will allow the air trapped inside to escape from the air release valves 2 amp 7 When all the air has escaped water will flow out of the valves 2 amp 7 When this occurs gently finger tighten the valves 2 amp 7 in a clockwise direction NOTE The plunger valve is equipped with a vacuum release valve that will automatically activate to minimize the suction at the pool outlet if the outlet is blocked This is an additional safety feature
10. VE GROUND P OOLS AGP s 18 x 42 549cm x 107cm 4 786 18 115 EASY SET POOL 18 x 48 549cm x 122cm 5 455 20 647 CIRCULAR 18 x 48 549cm x 122cm 6 423 24 311 I METAL FRAME POOL 24 x 52 732cm x 132cm 12 481 47 241 p 16 x 48 488cm x 122cm 5 061 19 156 18 x 48 549cm x 122cm 6 423 mw 4 18 x 52 549 x 132 6 981 26 423 ULTRA FRAME 20 x 48 7 947 30 079 POOL 22 x 52 671cm x 132cm 10 472 39 637 26 x 52 792cm x 132cm 14 667 55 515 08 was 4 SEQUOIA SPIRIT nee 168 x 4 124 1 19 1 4 18 8 x 53 569cm x 135cm 6 981 26 423 OVAL FRAME 20 x12 x 48 610cm x 366cm x 122cm 4 393 16 628 POOL 15 x 9 x 48 3 484 13 187 18 x 9 x 52 549cm x 274cm x 132cm 4 545 17 203 RECT ULTRA 24 x 12 x 52 732cm x 366cm 132cm 8 403 31 805 32 x 16 x 52 975cm x 488cm x 132cm 14 364 54 368 p SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English POOL CARE AND CHEMICALS All pools require care to keep the water clear and hygienically clean With proper chemical control your filter will help attain this objective Consult your pool supply dealer for instructions regarding the proper use of chlorine algaecide and other chemical agents required for sparkling clear water Keep pool chemicals away from children Do not replenish chemicals in pool while pool is occupied Skin or eye irritations could oc
11. cur Daily pH checking and chemical treatment of the water is very important and can not be overemphasized Chlorine algaecide and maintenance of proper pH levels are required when filling the pool as well as during the season Consult your local swimming pool supply store for instructions The season s first filling of the pool may have brackish water requiring extra water additives and extra filter changes Do not allow swimming in pool until the pH level is balanced Consult your local swimming pool supply store for instructions Keep spare filter cartridges on hand Replace cartridges every two weeks Chlorinated water may damage lawns gardens or shrubbery as children play in the pool and splash water outside the pool Lawn areas underneath the pool liner will be destroyed Note that some types of grass may grow through the liner Filter run time depends on pool size weather and usage level Experiment with various run times so as to produce clean clear water CAUTION Concentrated chlorine solutions may damage the pool liner Always follow the chemical manufacturer s directions and the health and hazard warnings CLEANING OR REPLACING FILTER CARTRIDGES It is recommended that the filter cartridge be replaced at least every 2 weeks Make sure the filter pump is turned off then disconnect the power cord from the electrical outlet Turn both plunger valve handles fully clockwise until they stop This closes the valve prevents the
12. dislodged when Put the o ring back into the groove connecting the hose Replacea new hose Hose broken AIR LOCK There s air trapped in the Open air release valve wait until water starts to flow pump housing and inlet hose out of the valves then close it The inlet and outlet hoses The lower position of pool outlet connects to filter connection are reversed pump water inlet The upper position of pool inlet connects to filter pump water outlet IMPORTANT If you continue to experience difficulty please contact our Consumer Service Department for assistance See separate Authorized Service Centers sheet SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 10 3 PANTONE 295U 06 21 2013 English COMMON POOL PROBLEMS PROBLEM DESCRIPTION SOLUTION ALGAE Greenish water Chlorine and pH levels Super chlorinate with shock Green or black need adjustment treatment Correct pH to your spots on pool liner pool store s recommended Pool liner is level slippery and or has Vacuum pool bottom a bad odor Maintain proper chlorine level COLORED Water turns blue Copper iron or maganese Adjust pH level to the WATER brown or black in water being oxidized by recommended level when first treated the added chlorine Run filter until water is clear with chlorine This is common Clean cartridge frequently FLOATING Water is cloudy or Hard water caused Correct the pH level Ch
13. e 17 unless it is damaged or leaking Replace the vacuum release valve immediately INSIDE LINER WALL SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 10 3 PANTONE 2951 06 21 2013 English POOL INLET NOZZLE amp PLUNGER VALVE SETUP optional In a counter clockwise motion unscrew plunger valve union from the threaded strainer connector 14 see drawing 5 Be careful not to lose the step rubber washer 11 Place the plunger valve on the ground in a safe place In a counter clockwise motion unscrew the strainer nut 12 from the threaded connector 14 Leave the flat washer 13 on the connector 14 Install the nozzle and plunger valve at the upper position of the pool inlet From the inside of the pool liner insert the connector 14 into one of the pre cut holes with the washer remaining on the connector to be placed against the inside of the liner wall Before assembly lubricate the threads with a petroleum jelly Then with the flat side of the strainer nut 12 facing the outside wall of the liner in a clockwise motion screw the strainer nut 12 back onto the threaded connector 14 see drawing 6 Finger tighten the adjustable pool inlet nozzle 15 and the strainer nut 12 onto the threaded connector 14 Grasp the plunger valve assembly Make sure the step washer 11 is in place In a clockwise motion screw the plunger valve union back onto the threaded conn
14. e emptying your pool for long term storage or relocation be sure the water is directed towards an acceptable drain water receptacle away from the house Check local regulations for specific directions regarding disposal of swimming pool water Disconnect power cord from electrical outlet Now drain the pool When the pool is empty disconnect all hoses from pump and plunger valves and remove the strainers from the pool wall Drain all water from the filter pump Leave filter pump pieces amp hoses outside to thoroughly air dry Remove both plunger valves from the threaded strainer connector 14 Be careful not to lose the step rubber washer 11 Coat the following O rings and washers with petroleum jelly for long term storage Air release valve amp sediment O rings 3 Filter housing cover O ring 5 Pump hose O rings 10 Strainer valve assembly step washers 11 Flat strainer rubber washers 13 Discard the used filter cartridge Put aside 1 or 2 new cartridges for next season s use Itis best to place all dry pieces in the original packaging for storage or placethem in an airtight plastic bag Store the unit and accessories in a dry place The storage s temperature should be controlled between 32 degrees Fahrenheit 0 degrees Celsius and 104 degrees Fahrenheit 40 degrees Celsius storage location IMPORTANT It is best to store away your poolsystem in its original packaging SAVE THESE INSTRUCTIONS 109
15. e of protective devices such as locked doors barriers etc Teach children what to do in case of an emergency Always use common sense and good judgement when enjoying any water activity Supervise supervise supervise For additional information on safety please visit The Association of Pool and Spa Professionals The Sensible Way to Enjoy Your Aboveground Onground Swimming Pool www nspi org American Academy of Pediatrics Pool Safety for Children www aap org Red Cross www redcross org Safe Kids www safekids org Home Safety Council Safety Guide www homesafetycouncil org Toy Industry Association Toy Safety www toy tia org SAFETY IN YOUR POOL Safe swimming depends on constant attention to the rules The NO DIVING sign within this manual can be posted near your pool to help keep everyone alert to the danger You may also wish to copy and laminate the sign for protection from the elements SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English LIMITED WARRANTY Your Krystal Clear Filter Pump has been manutactured using the highest quality materials and workmanship All Intex products have been inspected and found free of defects prior to leaving the factory This Limited Warranty applies only to the Krystal Clear Filter Pump and accessories listed below The provisions of this Limited Warranty apply only to the original purchaser and is not
16. e place The Filter Pump is an airtight system In a counter clockwise motion turn both air release valves 2 amp 7 1 2 turns to open DO NOT remove air release valves as water will expel with force if the motor is turned on and injury may occur Grasp and remove the filter housing cover 4 Check to see if a cartridge is inside the housing If yes replace the cover finger tighten the housing collar 1 back onto the filter housing Gently finger tighten the sediment release valve located at the bottom of the housing to be sure that water does not leak out When the pool is filled connect the hose from the bottom of the filter housing to the highest strainer assembly You will find the hose connection at the bottom of the plunger valve assembly Use the hose nut to attach the hose Connect the second hose which is fixed to the middle of the motor housing to the remaining liner connection A WARNING Position this product away from the pool so as to prevent children from climbing on it and accessing the pool WATER LEVEL PLUNGER VALVE E ASSEMBLY Sc FILTER HOUSING HOSE NUT ADJUSTABLE POOL COVER INLET NOZZLE AIR RELEASE VALVE FILTER HOUSING COLLAR THREADED MOTOR 4 STRAINER FILTER CARTRIDGE A HOUSING INSIBE HOSE O RING 7 INSIDE LINER OUTSIDE LINER WALL HOSE O RING INLET HOSE POWER CORD ILLUSTRATION N
17. eck MATTER IN milky by a too high pH level with your pool dealer for WATER Chlorine content is low advice Foreign matter in Adjust the chlorine level water Clean or replace your filter CHRONIC LOW Level is lower than Rip or hole in pool Repair with a patch kit WATER LEVEL on previous day liner or hoses Finger tighten all caps The drain valves are loose SEDIMENT Dirt or sand on Heavy use getting in Use Intex pool vacuum to ON POOL pool floor and out of pool clean bottom of pool BOTTOM SURFACE Pool too close to trees Use Intex pool skimmer DEBRIS Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will n
18. ector 14 see drawing 7 In a clockwise motion turn the plunger valve handle to close position Ensure the plunger valve is securely closed This will prevent water from flowing out during filling of the pool see drawing 8 NOTE Never cover the vacuum release valve 17 unless it is damaged or leaking Replace the vacuum release valve immediately Adjust the direction of the nozzle head pointing away from the pool outlet for a better circulation result see drawing 9 The pool liner is now ready to be filled with water Consult the above ground pool owner s manual for the filling instructions SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English FILTER PUMP HOSE CONNECTION SETUP Remove the Krystal Clear filter pump and hoses from the packaging Place the filter pump in such a manner that you can easily assemble the hose 8 connections to the plunger valve Note Some regional regulations may require the filter pump to be mounted stationary platform There are two mounting holes located in the pump base for this reason Consult your local authorities for filter pump mounting requirements Grasp the two pump hoses 8 and connect the hose nuts to the filter pump In a counter clockwise motion unscrew the threaded filter housing collar 1 from the filter housing Place it in a saf
19. nward refer to the parts depicted in the Parts List section of this manual To install do the following 1 Grasp the strainer and plunger valve mechanism 2 Ina counter clockwise motion unscrew plunger valve union from the threaded strainer connector 14 see drawing 1 Be careful not to lose the step rubber washer 11 Place the plunger valve on the ground in a safe place In a counter clockwise motion unscrew the strainer nut 12 from the threaded connector 14 Leave the flat washer 13 on the connector 14 Install the strainer and plunger valve at the lower position of pool outlet marked From the inside of the pool liner insert the connector 14 into one of the pre cut holes with the washer remaining on the connector to be placed against the inside of the liner wall Before assembly lubricate the threads with a petroleum jelly Then with the flat side of the strainer nut 12 facing the outside wall of the liner in a clockwise motion screw the strainer nut 12 back onto the threaded connector 14 see drawing 2 Finger tighten the strainer nut 12 onto the threaded connector 14 Grasp the plunger valve assembly Make sure the step washer 11 is in place In a clockwise motion turn the plunger valve handle to close position Ensure the plunger valve is securely closed This will prevent water from flowing out during filling of the pool see drawing 4 1 NOTE Never cover the vacuum release valv
20. ot occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help SAVE THESE INSTRUCTIONS 109 MODEL 633T FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 21 2013 English GENERAL AQUATIC SAFETY Water recreation is both fun and therapeutic However it involves inherent risks of injury and death To reduce your risk of injury read and follow all product package and package insert warnings and instructions Remember however that product warnings instructions and safety guidelines cover some common risks of water recreation but do not cover all instances or risk and or danger For additional safeguards also familiarize yourself with the following general guidelines as well as guidelines provided by nationally recognized Safety Organizations Demand constant supervision Learn to swim Take the time to learn CPR and first aid Instruct anyone who is watching your children about potential pool hazards and about the us
21. ten The nozzle and strainer Clean inside the plunger valve connection are reversed Pull valve handle to full upright position The vacuum release valve Install the nozzle at the upper position of pool inlet on the plunger valve is and the strainer at the lower position of pool outlet activated Turn off pump clear any debris or obstruction in the The vacuum release valve outlet remove all air from the filter pump and turn on the plunger valve is pump on again leaking Turn off pump if water leaking from the vacuum release valve then release valve needs to be replaced Contact Intex Service Center immediately to order replacement You may cover release valve with the cap temporarily if you ensure that the strainer cover strainer grid is installed and you Do Not run the pump while pool is occupied PUMP DOESN T Low water level Fill pool to correct water level WORK Strainer screen plugged up Clean strainer screens at pool inlet An air leak on the intake hose Tighten hose nuts check hose for damage Faulty motor or the impeller is jammed Clear any sticks or leaves in the intake hose An air lock inside the cartridge chamber Turn and pull valve handle to full upright position TOP COVER O ring missing Remove cover amp check for O ring LEAKING Cover or air release valve are not tight Tighten cover or valve Manually HOSE LEAKING Hose nuts are not well fitted Tighten or reinstall hose nut Hose o ring
22. transferable This Limited Warranty is valid for the period noted below from the date of the initial retail purchase Keep your original sales receipt with this manual as proof of purchase will be required and must accompany warranty claims or the Limited Warranty is invalid Krystal Clear Filter Pump Warranty 2 Years Hoses Plunger Valves amp Fittings Warranty 180 days If a manufacturing defect is found within the periods noted above please contact the appropriate Intex Service Center listed in the separate Authorized Service Centers sheet The Service Center will determine the validity of the claim If the Service Center directs you to return the product please carefully package the product and send with shipping and insurance prepaid to the Service Center Upon receipt of the returned product the Intex Service Center will inspect the item and determine the validity of the claim If the provisions of this warranty cover the item the item will be repaired or replaced at no charge Any and all disputes regarding the provisions of this Limited Warranty shall be brought before an informal dispute settlement board and unless and until the provisions of these paragraphs are carried forth no civil action may be instituted The methods and procedures of this settlement board shall be subject to the rules and regulations set forth by the Federal Trade Commission F T C IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY A
Download Pdf Manuals
Related Search