SineWave 20-480A Installation and user manual 2008ENG
Contents
1. I1 In 12 In 13 In MGE SineWave active conditioner load rates on each of the phases I1 root mean square current supplied by the conditioner on phase 1 In nominal root mean square current 3 Press A and V arrows to display the detailed spectrum of the current supplied by the utility power 11 MAINS SPECTRUM H1 xx H9 XX H3 xx H11 xx H lt 50 xx THDI xx H5 xx H7 Xx H1 H3 H11 detailed spectrum of first 11 harmonic orders THDI total harmonic distortion rate of the current supplied by the utility power 4 Press the function keys F2 and F3 to display phase 2 and phase 3 currents Displaying alarms List of alarms displayed MERY PC board fault 1 the main control and monitoring board is faulty The board must be replaced by the APC by Schneider Electric after sales service Internal fault this message informs the user of an internal conditioner fault which requires intervention by the APC by Schneider Electric after sales service Voltage out of tol the amplitude of the utility network voltage is out of the permitted limits Check the presence and amplitude of the utility power 3 phases and neutral The voltage tolerances permitted are defined in the section on characteristics and Language langue Principle measurements Secondary measurements Configuration JBUS communication Identification Reserved access 1 Choose the Alarms opt2. MAINT position on the CCTY card where the secondary terminals are connected The strap must remain in this position until the MGE SineWave conditioner has been put into service Sensor mechanical and electrical characteristics Closed sensors Important the shape of the sensor may be different depending on the rating and supplier Rating External Primary Secondary dimensions H1 H2 L P B1 B2 Max cable Diameter Cross sectional mm mm diameter of lugs area of wires A twisted 2 core cables mm 300 1 76 106 31 11 23 0 75 min 500 1 76 44 depending 0 75 recommended on supplier 2 5 max 1000 1 90 106 41 11 31 0 75 min 771 44 depending 0 75 recommended on supplier 2 5 max 1500 1 165 194 103 22 rod only 0 75 min 95 40 depending 0 75 recommended on supplier 2 5 max 2000 1 165 194 103 22 rod only 3or5 0 75 min 95 40 depending 0 75 recommended on supplier 2 5 max 3000 1 180 209 103 32 rod only 3or5 0 75 min 115 45 depending 0 75 recommended on supplier 2 5 max 4000 1 180 209 103 32 rod only 3or5 0 75 min 115 45 depending 0 75 recommended on supplier 2 5 max 5000 1 Available in option 6000 1 Available in option Page 24 51027008EN BD Max length of wires not supplied m 20 Installation cont Opening sensors Depending on availability opening sensors are of the OPTELEC or SACI type OPTELEC opening sensors On wiring kit supplied 600 1 sensor 200
3. Http oowerlearning apc com On line catalogue and registration Training center Schneider Critical Power amp cooling services 50 60 Hz United States Training Centre 132 Fairgrounds Road West Kingston RI02892 U S A Tel 1 877 800 4272 51027008EN BD Page 39 Characteristics and performances Technical reference base active conditioner characteristics 07 03 97 version Unless otherwise stipulated the performances given Is the table below are typical values corresponding to use under a nominal utility power voltage of 400 V three phase at 50 Hz at the nominal current Network input Functions Operating mode Technical characteristics Environmental conditions Page 40 51027008EN BD nominal voltage nominal frequency number of phases harmonic compensation power factor compensation cosine compensation single connected in parallel compensation capacity per phase compensation capacity in neutral conductor compensated harmonic orders dynamic capacity in dl dt response time reduction rate overload inrush current losses ventilation acoustic noise according to ISO 3746 ambient temperature rate or relative humidity operating altitude D 400 V 20 15 D 50 Hz 60 Hz 4 Hz gt 3 phases with or without distributed neutral operation possible on single phase or unbalanced loads gt global or ord
4. A p J A A ve ve ip wp 7 wg p p OG ty J p ws iy A V4 min 300 mm clearance for ventilation A min 80 mm 20 to 30 A ratings A min 200 mm 45 to 120 A ratings Page 10 51027008EN BD Installing 2 MGE SineWave conditioners side by side clearances must be provided to allow the circulation of an air flow of 1000 m per hour per cubicle The air is sucked below each conditioner and then expelled out the top the air temperature at the inlet to each conditioner must not exceed 40 degrees 25 C recommended power cables and signal cables arrive via the bottom of each conditioner Connecting power Determining wiring not supplied Wiring cross sectional areas shall be determined in compliance with the standards in force using the information in the table opposite and the protection tables per rating care should be taken with neutral cable sizing when the neutral is distributed owing to the majority presence of third harmonic which may lead to the current tripling in the neutral in relation to the phases Protections not supplied Protections shall be determined in compliance with the standards in force using the information below and in accordance with selectivity requirements These models are for guidance only and do not involve the responsibility of APC by Schneider Electric Installation cont 1 min ntilat 300 nce for Ven cleat The minim
5. current active harmonics conditioner Case of a 90 or 120 A unit MGE SineWave conditioner Er low voltage distribution switchboard Ul current network sensor harmonic current to be compensated load to be compensated MGET SineWave active harmonics conditioner 51027008EN BD Page 7 Installation cont each conditioner independently uses current measurements from three sensors whatever the state of the other conditioner running stopped de energized two cables between the conditioners allow each to know the other s state and thus determine the share of harmonics that it has to supply half or all if the other conditioner is not running each power circuit remains independent and has its own protection it is possible to connect up to 4 conditioners with the same rating in parallel to compensate the same load or the same group of loads Page 8 51027008EN BD Case of 2 parallel 20 A 30 A 45 A 60 A 90 A or 120 A MGE SineWave conditioners Example of 2 parallel 20 30 45 or 60 A MGE SineWave conditioners switchboard utility network lo low voltage distribution switchboard utility network harmonic current current sensor to be compensated load to be compensated MGE SineWave active harmonics conditioner harmonic compensating MGE sinewave current active harmonics conditione
6. provides access to the level 1 diagnosis and the F3 Reset key allows memorised faults to be acknowledged defined in the paragraph on characteristics and performances Harm current gt I nom the harmonic root mean square current absorbed by the load exceeds the MGE SineWave conditioner nominal current making it operate in current limiting mode the conditioner limits its compensating current to its nominal current rating e g 30 A root mean square fora 30 A MGE SineWave conditioner the load is not entirely compensated the harmonic current difference load harmonic compensating I remains on the utility power problems may occur in your installation depending on the rate of harmonics remaining on the utility power consult the APC by Schneider Electric after sales service 51027008EN BD Page 35 Operation cont Configuring The configuration of the conditioner carried out in the J factory will be checked when the conditioner is first energized and must not be further modified Only qualified APC by Schneider Electric personnel are allowed access gt Configuration The screen opposite is displayed after pressing F2 to confirm memorisation of the new parameters Page 36 51027008EN BD CONFIGURATION Enter Language langue Principle measurements Secondary measurements Alarms k k kkk password 8 Enter the password 4 characters the
7. reactive energy and harmonics Choice of compensated harmonic orders if this option is selected the harmonic orders to be compensated in order to optimise conditioner performance can be chosen Language langue Principle measurements Secondary measurements Alarms Configuration JBUS communication gt Identification Reserved access 1 Choose the Identification option using the A and V keys 2 Confirm the Identification option by pressing the ENT key 1 Press RUN to start the device or STOP to stop the device START UP Confirmation ENT Escape ESC This screen allows the command to be confirmed by pressing ENT or cancelled by pressing ESC only so that they may carry outa detailed survey of the conditioner s internal operation Operation cont Choice of application type the choice of application type is a parameter which is set in the factory It is defined in relation to the customers installation configuration Number of parallel connected devices Utility power voltage load supply voltage Derating depending on altitude IDENTIFICATION mo XXXXXXXXXXXX IS XXXA Un xxxV Fn xxHz With neutral Versions Xx Xx This screen displays the device serial number the nominal current in amps the nominal voltage in volts the nominal frequency in Hz the type of network with or without distributed neutral and the software versions built into th
8. system STR22SE 100 A 4p 3d magnetic threshold set at 2 x nom neutral protection via Vigi sensitivity 10 A TT earthing system C60 3x63 A curve B with Vigi C60 moduleTT earthing system Vigi Compact NS160 STR22SE 100 A 4p 3d magnetic threshold set at 2 x nom sensitivity depending on the installation TNC earthing system C60 3x63 A curve B TNS earthing system Important upstream breaking devices should be set in such a way as to guarantee good discrimination with the circuit breakers recommended on this page Is 150A PE Key Is sizing current Pcu breaking capacity Isc short circuit current NS160 STR22SE 160 A 4p 3d magnetic threshold set at 2 x nom Page 14 51027008EN BD Installation cont 60 A MGE SineWave Table of recommended protections per rating Connection to the SineWave TM terminal block where Pcu function of Isc Non distributed neutral Distributed neutral IT earthing system IT earthing system NC120H 3x80 A curve B Vigi Compact NS250 STR22SE 250 A 4p 3d magnetic threshold set at 2 x nom neutral protection via Vigi sensitivity 10 A TT earthing system NC120H 3x80 A curve B with Vigi C60 module TT earthing system Vigi Compact NS250 STR22SE 250 A 4p 3d magnetic threshold set at 2 x nom sensitivity depending on the installation TNC earthing system NC120H 3x80 A curve B TNS earthing system Important upstream breaking devices should be s
9. to be clearly displayed the MGE SineWave configuration to be modified to better meet specific applications conditioner operation to be controlled Use ENT key gt move to following menu gt confirmation of a choice ESC key gt return to previous menu gt cancellation of parameter setting in process and return to original values and V keys gt scrolling and selection from menu D choice of parameter General menu A menu is a screen offering a list of options and possible choices to select something from the menu gt use the A and V keys to choose the required option gt press ENT to confirm the chosen option Page 32 51027008EN BD Front view of terminal 1 Liquid crystal graphic display with back lighting 128 x 64 points i e 6 lines of 21 characters allowing information to be displayed 2 20 key keyboard 1 ENT key enter 1 ESC key escape 2 Aand W keys 11 number keys 0 to 9 and decimal point 3 function keys F1 F2 F3 2 command keys RUN and STOP protected by a removable protective cover gt setting of value use in or number keys from 0 to 9 and decimal point gt entering of passwords gt entering of numerical values function keys F1 F2 F3 gt F1 provides access to the help menu gt the functions of F2 and F3 depend on the menu displayed When a menu offers more
10. 0 1 sensor S1 blue S2 brown The sensors must be closed and screwed on both sides 600 1 sensor it is advisable to fix the sensor onto the cable Fixing lugs are provided for this purpose Important the shape of the sensor may be different depending on the rating and supplier Rating extemal Primary Secondary Dimensions Fixing centre Diameter of Max cable Fine wire Cross sectional Max length distance C screws diameter connection area of wires of wires 2 core cables mm m 600 1 wiring kit supplied 0 75 min 20 5 m 0 75 recommended 2 5 max 2000 1 D2 137 5 D1 69 wiring kit supplied 0 75 min L 298 or rod D1 69 5m 0 75 recommended D3 206 2 5 max SACI opening sensors 600 1 2000 1 sensors Wiring kit not supplied we The sensors must be closed and screwed on both sides 600 1 and 2000 1 sensors it is advisable you fix the sensor to the bar Fixing lugs are provided for this purpose Important the shape of the sensor may be different depending on the rating and supplier Dimensions Max cable Diameter of Cross sectional area of wires Max length of wires mm diameter screws mm 2 core cables mm m 600 1 5 0 75 min 20 0 75 recommended 2 5 max 2000 1 5 0 75 min 20 0 75 recommended 2 5 max 51027008EN BD Page 25 Installation cont Mounting direction of sensors The current sensors must be mounted on each of the e phase
11. 00 1 Current sensor 5000 1 1 Current sensor 6000 1 5 Choose the sensor rating using the arrows and press ENT MEMORIZATION Confirmation ENT Escape ESC MEMORIZATION Memorization in progress WARNING Memorization STOP of SineWave T Confirm memorization by pressing ENT or cancel modifications in progress by pressing ESC This screen is displayed while the parameters are being saved wait a few seconds for the general menu to be displayed before starting the MGE SineWave up again Configuration parameter lists Sensor rating choose the rating of the sensors used to measure the load currents Type of utility power utility power with or without distributed neutral RUN STOP authorisation via JBUS communication port authorisation or non authorisation of remote RUN and STOP commands via the JBUS communication port J BUS communication Parameter setting of the communication port is described Is the specific J BUS communication port manual Identification RUN STOP commands Reserved access This command provides access to the centre of the system and is for APC by Schneider Electric personnel Reactive compensation or no reactive compensation compensation or no compensation of the reactive energy Reactive energy compensation is carried out to the detriment of harmonic compensation and it is therefore necessary to oversize the conditioner if it is required to compensate both
12. 120 A ratings The air is sucked in below the conditioner and expelled via the top Z min min the air temperature at the inlet of each P 150 mm 50mm clearance clearance conditioner must not exceed 40 degrees 25 C recommended the power cables and fine wires arrive via the bottom of the conditioner To installa 90 Aor120A conditioner refer to how to ad install 2 conditioners on top of each other or side by side 300 mm clearance for wiring and ventilation Installing 2 MGE SineWave Side view conditioners on top of each other in a re T a cubicle min 300 mm clearance AN Installing 2 for ventilation MGE SineWave conditioners on top of each other must only be done inside a cubicle Openings must be provided at the top and bottom of the cubicle to help the conditioners to cool down a ventilation deflector must be used so that the thermal characteristics of the 2 conditioners are respected The distance between the two cubicles is determined by the height the air is sucked below each conditioner and then expelled gt out the top for the top conditioner gt to the rear for the bottom conditioner the air flow required for cooling the cubicle is 2000 m per hour the air temperature at the inlet to each conditioner must not exceed 40 degrees 25 C recommended power cables and signal cables arrive via the bottom of the conditioner AA a Ve Uy
13. Care must be taken to ensure that the phase order and polarity of the sensors are respected Once the connections have been made refit the CCTY card to the PARY card the connection leads supplied with the conditioners will allow the MGE SineWave conditioners to operate in parallel via loop communication Captor used if neutral connected Page 28 51027008EN BD For 90 A or 120 A parallel units Ri Gi phase 1 to load phase 2 phase 3 ID gt WW Fig 1 PARY board NORMAL MAINT CCTY board copper side Strap X1 for short short circuiting the current sensors phase 1 phase 2 phase 3 CCTY board component side once removed and turned over phase 3 phase 2 phase 1 The secondary terminals of AN the current sensors must be short circuited as soon as they are installed by placing the strap X1 in the MAINT position on the CCTY card The strap X1 will remain in the MAINT position until the MGE SineWave conditioner has been put into service see adjacent diagrams Connection Remove the CCTY card that is plugged into the PARY card via the XR4 connector Turn the CCTY card over to connect the secondary terminals of the current sensors to the screw terminals XR1 XR2 and XR3 of this card Care must be taken to ensure that the phase order and polarity of the sensors are respected Onc
14. MGE SineWave 20 480 A Active harmonics conditioner QU V S m i V manual by Schneider Electric To the user We would like to thank you for choosing the MGET SineWave active harmonics conditioner and welcome you to the ever increasing world wide family of satisfied APC by Schneider Electric product users This manual has been written to provide you with all the information necessary to install and operate your MGET SineWave active harmonics conditioner We remain at your entire disposal should you require any further details Advice for safety Danger dangerous voltages A N are present inside the conditioner Any intervention requiring the door or protection panels to be opened must be carried out by qualified personnel Pictograms Important instructions that must be followed Information advice help Action ajoe Page 2 51027008EN BD the conditioner must be earthed do not place the conditioner near liquid or in an excessively damp environment do not obstruct the air vents do not place the conditioner in direct sunlight or near a source of heat APC by Schneider Electric if the conditioner in stored before use it must be kept in a dry place Storage temperature between 20 C and 45 C do not store horizontally dispose of packing waste in compliance with legal provisions in force Contents dENI
15. NCAN ON seerne 5 SANTA se mania te toaetenee at 5 Principle Improvements offered by MGE SineWave rrrnnnrnrnrrnrnrvrrnnrrernrnnnnnen 6 Operating TINT Se cre are eta aed ela 6 Device functional features cc cccccccecccceeeeeeeeeeeeeeeeaeeeeeseeeeseeeeeeseeeeees 6 Installation Standard arrangements ccccccecceeceeeeeeeceeeeeeeseeeeeeeseeeeeeseaeeeeeeseeseeesaaess 7 Installing device s cece ceeeeeeeeeeeeeeceeeeeeeeseeeeeeeseeeeeeseaceeeesaeseeesseneeeeeeas 9 Mechanical characteristics ua aserd poser dee bes catieeendeepeasel enka 9 Install tion TEQUIFEIMEINS sracte anae ae eee eee ee 10 COMME CUING DOW CF saa Aves seere 11 Connecting dry contacts and communication port optional 08 21 Connecting ribbon cables for 120 A and parallel installation 0008 22 Moving the graphic terminales siasii a a 23 Installing current sensors rrrrnnnrrrnnrrrrnnrrrrnnrennnrrnrnnrrnnnrennnsnennnnrennnnsennnsne 23 Sensor mechanical and electrical characteristics rrrrnrrnrrrnrrrrrrnnrrrrnrnnnnren 23 Mounting direction Of sensors ccccceseeecccceseececeeeeeeccesececsesseeessuseeesssaaaees 26 HAS TANNING SENS ONS HR E 26 COMME CUNOG SCMSONS arsen ee eee 29 Energization and de energization EnErgIZINO r er 30 General auv2stsserr ee Sata obese aa ee aas eau nese 30 Starting the MGE SineWave conditioner rrnrrnnnnnnnnnnnrrnrnnnnnrnnn
16. No Reactive compensation gt YES or NO gt Hn YES or NO gt speed format parity nb stop bits address gt 0t05 gt 11t04 D O to 100 D 208 V 220 V 240 V 400 V 460 V 500 V 575 V 700 V D O to 9000 seconds D green led normal operation D red led conditioner OFF D orange led inverter in limitation D display of measurements and alarms D implementation guide diagnosis D entry of customer parameters D conditioner RUN push button D conditioner STOP push button D 2 x conditioner running stopped D 1 x limiting operation gt 680 mm 20 A 30 A gt 780 mm 45 A 60 A gt 2x 780 mm 250 mm 90 A 120A gt 620 mm 20 A 30 A gt 720 mm 45 A 60 A D 2 x720 mm 250 mm 90 A 120A gt 540 mm 20 A 30 A gt 590 mm 45 A 60 A gt 590 mm 90 A 120A gt 280 mm 20 A 30 A gt 325 mm 45 A 60 A gt 325 mm 90 A 120A D 65 kg 20 A 30 A gt 110 kg 45 A 60 A gt 220 kg 90 A 120A RAL 9002 light grey EN 60950 1 IEC 60146 IEC 60529 NFEN 60529 IP205 EN 55011 level A IEC 61000 4 1 IEC 61000 4 2 level 3 IEC 61000 4 3 level 3 10 V m IEC 61000 4 4 level 4 IEC 61000 4 5 level 3 in differential mode level 4 in common mode IEC 61000 4 6 level 3 10 V 51027008EN BD Page 41 Page 42 51027008EN BD
17. aced on each of the 120A SineWaves 51027008EN BD Page 19 Installation cont Connection operations Connection operations must be carried out without the conditioners being energized For the protection of persons remember that the PE or PEN protective conductor must always be connected first Earthing system MGE SineWave is suited to all types of earthing system Procedure check that the lifting sling has been removed check that the MGE SineWave supply circuit breaker placed in your low voltage switch cubicle is in open position O wiring is connected via the bottom in front of the conditioner to access the connection terminal block remove the front and lower protection plates power connections are made on the bolted terminal block the lower protection plate of the power terminal block must be fitted with bushings for cable feedthrough If several holes are made to feed the cables through cut a slot common to all the holes to prevent eddy currents from being generated connect the PE or PEN conductor first connect the other conductors so that they comply with the rotation direction of the phases and the indications in the figures opposite The connecting cables must AN be mechanically fixed near the terminal block so that any mechanical stress on the conductors is prevented Note If there is traction on the cables the PE or PEN must be the la
18. ate conditioner stopped red indicator Q lamp lit The conditioner has stopped following a manual STOP command or an operating anomaly Consult the user interface to know what the fault is due to and what action to undertake in order to correct the anomaly current limiting operation green indicator lamp lit and orange indicator lamp flashing The harmonic RMS current absorbed by the load exceeds the MGE SineWave nominal current The conditioner thus operates in current limiting mode gt the conditioner limits its compensating current to its nominal current rating e g 30 A RMS for a 30 A MGE SineWave conditioner gt the load is not entirely compensated gt the harmonic current difference load harmonic compensating remains on the utility power gt consult the chapter on what to do in case of an alarm red indicator conditioner stopped 51027008EN BD Page 31 Operation cont Control and monitoring interface Presentation The MGE SineWave active harmonics conditioner has a highly user friendly graphic terminal on the front panel which makes the product easy to use This terminal may optionally be moved to the front panel of a switch board from the conditioner using a separate supply cable This terminal allows the language of the displayed messages to be chosen from a selection of 7 languages the conditioner identification and operating parameters
19. e compensation introduced by MGE SineWaveT in relation to harmonic and reactive currents Is continuously recalculated the MGE SineWave active harmonics conditioner continuously measures current absorbed by the load and immediately modifies the current that it reinjects onto the utility power to match this value the MGE SineWave active harmonics conditioner is suitable for all installation load and harmonic spectrum variations thus guaranteeing optimum operation at any instant Standard arrangements Depending on the type of problem to be solved the position of the sensors and that of the The MGET SineWave harmonics conditioner connection point may be different from one installation to another The audit carried out before installation enables the optimum respective positions to be determined The MGET SineWave conditioner is connected in parallel with the load The MGE SineWave harmonics conditioner will be fed from a specific outgoing feeder This line must be protected by a circuit breaker The MGE SineWave conditioner uses this line to send harmonics destined to compensate the load harmonics back onto the utility power Installation Case of a 20 A 30 A 45 A or 60 A unit MGE SineWave conditioner low voltage distribution switchboard utility t network curren sensor harmonic current to be compensated load to be compensated
20. e control and monitoring board 3 Press ESC to return to the general menu 51027008EN BD Page 37 Maintenance Maintenance Before any intervention in the MGE SineWave conditioner switch off the power supply and wait for the capacitors to discharge 5 min on the current sensor connection short circuit the sensor secondaries The MGE SineWave harmonics conditioner does not require any preventive maintenance It is nevertheless advisable to carry out the following at regular intervals check the state and tightness of connections make sure that the temperature of the air at the MGE SineWave conditioner inlet is below 40 degrees clean the air vents and check that ventilation is efficient What to do Is case of an alarm Symptoms Terminal and indicator lamps off Terminal OFF MERY PC board fault 1 MERY PC board fault 2 Internal fault Voltage out of tol Frequency out of tol Internal overtemp Orange indicator lamp flashing Page 38 51027008EN BD Corrective actions check the voltage at the MGE SineWave conditioner input The voltage tolerances permitted are defined in the section on characteristics and performances check that the graphic terminal is plugged in ask the APC by Schneider Electric after ales service to intervene ask the APC by Schneider Electric after ales service to intervene ask the APC by Schneider Electric after ales
21. e the connections have been made refit the CCTY card to the PARY card the connection leads supplied with the conditioners will allow the MGE SineWave conditioners to operate in parallel via a loop communication other leads supplied with the conditioners will ensure connections between the two cubicles which make up each 120 A Captor used if neutral connected Connecting sensors Connection operations The signal cables connecting 9 the current sensors to the g MGET SineWave conditioner must be moved away from the power cables so that any disturbance is avoided For 90 A or 120 A parallel units PARY board NORMAL MAINT CCTY board copper side phase 1 phase2 phase 3 Procedure wiring is connected via the bottom in front of the conditioner the signal cables connections are made on 3 screw terminals The signal cables must be mechanically fixed near the e terminals so that any mechanical stress on the conductors is avoided Installation cont Strap X1 for short short circuiting the current sensors CCTY board component side once removed and turned over phase 3 phase 2 phase 1 put back the protection panels and close the door close the MGE SineWave conditioner protection circuit breaker 51027008EN BD Page 29 Energization and de energization The conditioner must be energized for the first time by e j qualified APC by Schne
22. ed neutral IT earthing system Vigi Compact NS160 LAS STR22E 100 A 4p 3d Vigi Compact NS160 magnetic threshold set at 2 x nom STR22E 100 A 4p 3d neutral protection via Vigi magnetic threshold set at 2 x nom sensitivity 10 A neutral protection via Vigi sensitivity 10 A TT earthing system Vigi Compact NS160 Is lt 50A STR22E 100 A 4p 3d Vigi Compact NS160 magnetic threshold set at 2 x nom STR22E 100 A 4p 3d sensitivity depending on installation magnetic threshold set at 2 x nom sensitivity depending on installation TNC earthing system C60 3x63 A curve B C60 3x63 A curve B Is lt 50 A TNS earthing system P 2 3 N Is 150 A Is 150 A PE PE NS160 STR22E 160 A 4p 3d Is lt 50 A magnetic threshold set at 2 x nom NS160 STR22E 160 A 4p 3d magnetic threshold set at 2 x I nom Al Important upstream breaking devices should be set in such a way as to guarantee good discrimination with the circuit breakers recommended on this page 2 vigi compacts placed on each of the 90A SineWaves 51027008EN BD Page 17 Installation cont 120 A MGE SineWave with non distributed neutral Table of recommended protections per rating Connection to the MGE SineWave terminal block where Pcu function of Isc Non distributed neutral IT earthing system NC120 3x80 A NC120 3x80 A curve B curve B TT earthing system NC120 3x80 A NC120 3x80 A curve B curve B with Vigi C60 module f
23. er by order gt possible to set parameters D up to 4 D20 Ar m s D 30 Ar m s gt 45 Ar m s gt 60 Ar m s gt 90Ar m s gt 120 Ar m s note the compensation capacity decreases with the frequency of the harmonic orders to be compensated D 60 Ar m s D 90 A r m s D 135 Ar m s D 180 Ar m s D 270 Ar m s D 360 Ar m s D H2 to H50 parameter setting possible D global or selective compensation D gt 100 kA s for 20 A and 30 A D gt 200 kA s for 45 A and 60 A D gt 400 kA s for 90 A and 120 A D 40 ms D load THDI network THDI gt 10 at the conditioner nominal current if D load THDI gt 40 D network THDI gt 4 at the conditioner nominal current if load THDI lt 40 Global compensation reduction rate THDI _harmonic I basic D limiting to nominal current continuous limiting operation possible D lt nominal current without matching transformer D lt 1000 W at 20 A lt 1200 W at 30 A D lt 1900 W at 45 A lt 2400 W at 60 A D lt 3800 W at 90 A lt 4800 W at 120 A D forced air inlet via bottom and outlet via top D 1000 m h for 20 to 60 A ratings D 2000 m h for 90 to 120 A ratings D lt 58 dBA at 20 A D lt 59 dBA at 30 A D lt 62 dBA at 45 A D lt 64 dBA at 60 A D lt 65 dBA at 90 A D lt 67 dBA at 120 A At the nominal current on computer load according to ISO 3746 D 0 a 40 C permanently 0 to 95 relative humidity without condensation D lt 1000 m without derating above
24. et in AN such a way as to guarantee good discrimination with the circuit breakers recommended on this page If the 250A rating of the STR22SE trip unit does not make it possible to ensure discrimination with the existing upstream protection devices it is possible to replace it with a circuit breaker with a 160A rating for applications in which the neutral current for harmonics elimination does not exceed 160A Key Is sizing current NS250 STR22SE 250 A 4p 3d Pcu breaking capacity rd magnetic threshold set at 2 x nom 51027008EN BD Page 15 Installation cont 90 A MGE SineWave with non distributed neutral Table of recommended protections per rating Connection to the MGE SineWave terminal block where Pcu function of Isc Non distributed neutral IT earthing system C60 3x63 A curve B C60 3x63 A curve B Is lt 50A TT earthing system C60 3x63 A curve B C60 3x63 A curve B with Vigi C60 module with Vigi C60 module Is lt 50 A Important upstream breaking AN devices should be set in such a way as to guarantee good discrimination with the circuit breakers recommended on this page Key Is sizing current Pcu breaking capacity Isc short circuit current Page 16 51027008EN BD Installation cont 90 A MGE SineWaveT with distributed neutral Table of recommended protections per rating Connection to the SineWave terminal block where Pcu function of Isc Distribut
25. ider Electric personnel who will carry out the necessary checks to make sure that operation of the installation is optimum Energization close the conditioner supply circuit breaker on your low voltage supply switchboard General if the load harmonic current is higher than the MGE SineWave s capacity to eliminate harmonics the orange indicator lamp will flash whether the conditioner is running or stopped to access the RUN and STOP keys remove the protection cover located at the bottom of the terminal MGET SineWave starting and stopping can be controlled manually using the terminal keyboard or via the communication link if MGE SineWave conditioners are connected in parallel each conditioner can be started or stopped independently of the others Important to enable the MGE SineWave conditioner to operate remove the short circuit from the current sensors secondary windings by moving the strap X1 on the CCTY card from the MAINT position to the NORMAL position gt the conditioner stopped red indicator lamp lights up gt the terminal screen lights up protection cover Starting the MGE SineWave conditioner Press the RUN key on the terminal to start the MGE SineWave conditioner and then confirm the command displayed on the terminal by pressing the ENT key the MGE SineWave conditioner starts and is then operational The red i
26. iguration of parallel conditioners 00000000 00000000 00000000 00000000 00000000 00000000 Moving graphic terminal The MGE SineWave harmonics Cutting and fixing template for the conditioner graphic terminal can be moved terminal moved to the front panel of a switch cubicle where a MGE SineWave is installed To do this use the optional kit reference n 5102726400 which contains gt a cover plate replacing the terminal located on the MGE SineWave door D a 2 5 metre long extension lead This lead cannot be lengthened without this causing a risk of abnormal operation Moving the graphic terminal gt disconnect the terminal ribbon cable on the back of the door gt remove the terminal by unscrewing the 4 fixing screws gt use these 4 screws to fix the cover plate in place of the terminal gt connect the ribbon cable onto the extension lead gt feed the extension lead through the rectangular bushing at the bottom of the MGET SineWave conditioner gt fix the terminal at the required location gt connect the extension lead to the graphic terminal 51027008EN BD Page 23 Installation cont Installing current sensors supplied Once installed the current sensor secondaries must be short circuited The secondary terminals of the current sensors must be short circuited as soon as they are installed This short circuit is achieved by moving a strap X1 to the
27. ion using the A and V keys The choice must be displayed on the screen in reverse video 2 Confirm the Alarms option by pressing the ENT key The following screen is displayed during normal operation conditioner running and no anomaly present ALARMS No Alarm SineWave Keeps your electrical AC network clean performances Frequency out of tol the utility power frequency is out of the permitted limits Check the utility power frequency The frequency tolerances permitted are defined in the section on characteristics and performances MERY PC board fault 2 the main control and monitoring board is faulty The board must be replaced by the APC by Schneider Electric after sales service Internal overtemp the conditioner has been stopped by the thermal protection thus avoiding damage to the equipment Check that the 3 ventilators are operating correctly that the air vents are clean and check the temperature of the room The temperature tolerances permitted are Operation cont In the event of an operating anomaly the following screen is displayed with the active alarms only ALARMS Start up inhibited MERY PC board fault 1 Internal fault Voltage out of tol Diag Reset AV Frequency out of tol MERY PC board fault 2 Phase rotation WRONG Internal overtemp Harm current gt Inom Conditioner OFF The A and V keys allow 2 pages of faults to be displayed The F2 Diag key
28. ity power as a globally linear load which absorbs sinusoidal current Thus the cabling and generator impedances will not introduce any voltage distortion Device functional features The MGE SineWave active harmonics conditioner allows determination of the harmonic orders to be compensated gt by configuring the breadth of the spectrum to be compensated gt or by concentrating the capacity of the MGE SineWave compensation on specific harmonic orders during installation and thus carrying out selective compensation reactive energy compensation to be carried out so as to increase the load cosine and return to the cosine range applied by the energy utility Page 6 51027008EN BD well as device operating problems due to over heavily disturbed supply voltages an installation s characteristics to be improved so that devices can operate in conditions specified by the manufacturer reactive energy to be compensated when this type of operation is possible and the cosine to be converted to a value higher than or equal to 0 94 as recommended by electricity utilities MGE SineWave measurements and other variables calculated by the device voltage current distortion rates etc to be displayed optional communication with an external controller via a J BUS protocol RS422 485 link for gt transmitting display information gt receiving RUN and STOP orders Th
29. lel connection board using the indications in the table below Signal cables connections AN must be mechanically fixed near the connectors so that any stress on the conductors or conductor shielding earthing is prevented Page 22 51027008EN BD shielded strand supplied 5 m 20 A or 60 A parallel conditioner connection 90 A or 120 A parallel conditioner connection Type of conductors Remark shielded strand supplied 3 m connection between the 2 cubicles which make up the 90 or 120 MGE Sinewave loop connection allows parallel operation of the MGE Sinewave even if it is interrupted for the number of devices to be modified 90 A or 120 A parallel conditioner connection 1 cable for controlling the 2nd 90 Aor 120A cubicle 2 strands for 2 strands for parallel parallel connection connection 2nd 90 or 120 A conditioner cubicle connection cable coming from the 1st 1 cable for controlling the 2nd 90 A or 120 A cubicle 90 A or 120 A cubicle Close up of connectors MERY board inter cubicle connector connection between two boards PARY board configuration straps and switches for parallel connection parallel installation connectors Sd Lo Ca EN 2 equivalent connectors Installation cont Table of strap configurations for each parallel conditioner MGET SineWave n 1 MGE SineWave n 2 MGE SineWave n 3 MGE SineWave n 4 00000000 conf
30. n by pressing the ENT key MAINS LOAD 11 xxxA 12 xxxA I3 xxxA IN xxxA l1 xxxA 12 XxxA I3 xxxA IN xxxA 11 12 13 IN actual root mean square values in amps of the 3 phases and neutral of the current supplied by the utility power current absorbed by the non linear load Displaying secondary measurements Page 34 51027008EN BD Language langue Principle measurements Secondary measurements Alarms Configuration JBUS communication Identification Reserved access 1 Choose the Secondary measurements option using the A and V keys 2 Confirm the Secondary measurements option by pressing the ENT key 11 LOAD SPECTRUM H1 xx H9 XX H3 xx H11 xx H lt 50 xx THDI xx H5 xx H7 Xx H1 H3 H11 detailed spectrum of first 11 harmonic orders THDI total harmonic distortion rate of the current absorbed by the load 9 Press the A and V keys to run over the main measurement screens circular loop display MAINS LOAD THDI1 xx THDI1 xx THDI2 xx THDI2 xx THDI3 xx THDI3 xx Umains xxxV THDI1 THDI2 THDI3 distortion rates of the 3 phases THDI I harmonic I basic of the current supplied by the utility power current absorbed by the non linear load Umains average value of the 3 utility network phase to phase voltages LOAD LEVEL SINEWAVE 11 In XXX 12 In XXX I3 In XXX
31. n press ENT The password characters are displayed by an JBUS communication Identification Reserved access 1 Choose the Configuration option using the A and V keys 2 Confirm the Configuration option by pressing the ENT key The Configuration Menu screen is again displayed for modification of other parameters if required CONFIGURATION MENU Current sensor 1000 1 Neutral connected ON OFF JBUS validated Reactive compensated CONFIGURATION MENU Current sensor 1000 1 Neutral connected ON OFF JBUS validated Reactive compensated Harmonics choice Application 0005 Nb of units 2 Mains voltage 400 V Harmonics choice Application 0005 Nb of units 2 Derating 10 Mains voltage 400 V Sensor connected Startup delay s 20 Derating 10 Sensor connected Startup delay s 20 Choose the parameter to be modified using the A and W keys and press ENT 6 Press F2 Mem key to memorise the new parameters COMPENSATION CHOICE Inductive reactive Capacitive reactive Ind amp Cap reactive Reactive uncompensa For example modification of the rating of the sensors used to measure load currents SENSOR SIZE CHOICE Current sensor 300 1 Current sensor 500 1 Current sensor 600 1 Current sensor 1000 1 Current sensor 1500 1 Current sensor 2000 1 i Current sensor 3000 1 Current sensor 40
32. ndicator lamp goes off and the green lamp lights up The MGE SineWave 9 conditioner will be automatically restarted when energized following disappearance of the utility voltage during operation of the MGE SineWave conditioner If it is not energized following the disappearance of the utility voltage the MGE SineWave conditioner will remain stopped Stopping the MGE SineWave conditioner to stop the MGE SineWave conditioner manually press the STOP key and confirm the displayed command be pressing the ENT key on De energization The MGE SineWave conditioner can be de energized whatever its state running or stopped Page 30 51027008EN BD the terminal the MGE SineWave conditioner stops and no longer carries out compensation The green indicator lamp goes off and the red indicator lamp lights up gt after several seconds the general menu is displayed on the terminal screen Operation Signification of indicator lamps The conditioner s operating state is given by common indications User interface simple indications Common indications User friendly interface green indicator conditioner running These clearly indicate Q normal operation green indicator lamp lit The MGE SineWave conditioner is Q orange indicator conditioner limiting current eliminating harmonics on the utility power This is its normal operating st
33. nnnnen 30 Stopping the MGE SineWave conditioner rrrrrnnrnnrnnnnnrnnnerrnnnennnnrr 30 De enerqIZ2nguvrsa 4Gedsraau See 30 Operation Signification of indicator lights rrrrrrnnrrorrrnnnrrrrnnnrrrrrrnnrrrnrnnnrrrnrnnrrrnnnnn 31 USE INE DEE 31 User friendly interface rrrnnrrnnnnnnnnrnnnnnrvnnnnnrernrnnnnrnnnnsnnennnnnsrennnnnsnnnnrnsennnnnn 31 Control and monitoring interface rrrrrrnnrrnrnnnnnnrnrnnnnrerrrnnnrrnrnnerennnnnnnnen 32 Presens amanda ae 32 USE su 32 General MENU srie ee a e ia a a a e a 32 CHOICE OF TAN GUAGE Se 33 Displaying main measurements arrnnnnnnnnvnnnrnnnnnvnnnnnvnnnnnennnnnennnnssnnnnssnvnnsennnn 33 Displaying secondary measurements ccceeeceeseeeeeseeeeeeeeeesseeeeseeeeesaeeeeeaaes 34 Displaying AIAN EE EE tata aaia 35 COMGUNNG uran 36 JEBUS COMMUNICAUOMN vaare 37 derme 37 RUN STOP COMMONS Lisemsaserkesebesan bee baade 37 Reserved SLET 37 Maintenance Maintenance Las sjderkbe eksakt enten ounebouxe 38 What to do in case of an alarm rorrrrrnnnnnrorrnnnnrrnrnnnrrrrnnnnnennvnnnrrrnnnsrsrnnnnnn 38 Training Centers oanien e a E aa eda one eanens 39 Characteristics and performances ornrvrrvrrrrrvrrvrrververrerverrervennenvenennn 40 51027008EN BD Page 3 Page 4 51027008EN BD Installation of the MGET SineWave active harmonics conditioner monitoring of correct operation and certain repairs must be carried out by qualified personnel trained t
34. nt Sub D not supplied dry contact cable not supplied removable connector with polarization supplied with conditioner communication link optional not supplied configuration of 9 point Sub D connector for RS 422 485 communication link optional the communication link can be plugged into the sub D connector without shutting down the MGE SineWave this interface complies with safe extra low voltage insulating requirements MGE SineWave connector seen from below Key pin 1 0 volts pin 2 RP_5V pin 3 RC_A pin 4 RD B pin 5 TD B pin 6 RP_OV pin 7 RC B pin 8 RD A pin 9 TD A 51027008EN BD Page 21 Installation cont Connecting ribbon cables for the 90 or 120 A and for parallel installation Type of connections Connector 90 or 120 MGE SineWave inter cubicle connector MGE SineWave parallel connector Connection operations for parallel or 90 A or 120 A conditioners Connection operations must be carried out with the conditioner de energized Procedure wiring is connected via the bottom in front of the device remove the protection plate the conductor connectors must be correctly locked shielding shall be earthed in compliance with the indications given below connector shielding I N ea as earthing block 90 Aor 120 A MGE SineWave inter cubicle connection configure the paral
35. o deal with electrical hazards Other operations may be carried out by any other persons with the help of this manual All MGE SineWave range products are protected by patents they implement original technology which cannot be used by any competitor of APC by Schneider Electric Copies of this document may be made with the approval of APC by Schneider Electric and must bear the compulsory title APC by Schneider Electric MGE SineWave installation and operation manual n 51027008XT Identification label Check that your utility supply is RS compatible with the characteristics given on the identification label placed inside the door of the MGE SineWave active harmonics conditioner Standards the MGE SineWave active harmonics conditioner complies with the main international standards in force for this type of equipment and notably concerning gt design IEC 146 gt construction and safety EN 60950 1 gt noise ISO 3746 Identification standards Are SINEWAVE by Schneider Electric Filtre Actif 60 A RESEAU MAINS NETZ Ue Uin Ue Fr quence Frequency Frequenz Capacit de compensation Compensation power Kompensations Strom Article Article 5102700200 NT 02 Artikel Code Usine Plant Code VH N S rie Serial number Seriennummer VH 452E4004 Code barre Bar code Nombre de cellule Number of unit Anzhal de zellen 1 1 Made in Designed and man
36. or NC100 Is lt 50 A with Vigi C60 module for NC100 Important upstream breaking AN devices should be set in such a way as to guarantee good discrimination with the circuit breakers recommended on this page Key Is sizing current Pcu breaking capacity Isc short circuit current Page 18 51027008EN BD Installation cont 120 A MGE SineWaveT with distributed neutral Table of recommended protections per rating Connection to the MGE SineWave terminal block where Pcu function of Isc Distributed neutral IT earthing system Vigi Compact NS160 STR22E 100 A 4p 3d Vigi Compact NS160 magnetic threshold set at 2 x I nom STR22E 100 A 4p 3d neutral protection via Vigi magnetic threshold set at 2 x I nom sensitivity 10 A neutral protection via Vigi sensitivity 10 A Vigi Compact NS160 STR22E 100 A 4p 3d Vigi Compact NS160 magnetic threshold set at 2 x I nom STR22E 100 A 4p 3d sensitivity depending on installation magnetic threshold set at 2 x nom sensitivity depending on installation TNC earthing system NC120H 3x80A curve B NC100H 3x80A curve B TNS earthing system NS250 STR22E 250 A 4p 3d Is lt 50 A magnetic threshold set at 2 x nom NS250 STR22E 250 A 4p 3d magnetic threshold set at 2 x I nom Al Important upstream breaking devices should be set in such a way as to guarantee good discrimination with the circuit breakers recommended on this page 2 vigi compacts pl
37. r current sensor harmonic current to be compensated load to be compensated MGE SineWave active harmonics conditioner MGE SineWave active harmonics conditioner Installation cont Installing device s Mechanical characteristics Dimensions Fixing centre Diameter mm distance of fixing mm screws mm Height Width H C1 20 A and 30 A conditioners 45 A and 60 A conditioners 780 590 325 1528 7600 8 110 90 A and 120 A conditioners are made up of two cubicles having the same dimensions as the 45 and 60 A conditioners These cubicles can be placed side by side or on top of one another subject to installation requirements relating to ventilation 51027008EN BD Page 9 Installation cont Installation requirements The MGE SineWave transformer motor etc Whatever the installation A N active harmonics it may be installed in a cubicle or fixed A method a 600 mm minimum conditioner must be against a wall clearance must be provided mounted vertically and away in front of the from any source of heat MGE SineWave heating system conditioner allowing for the door to be completely opened 300 mm min clearance for ventilation Installing a MGE SineWave conditioner alone clearances must be provided to allow the circulation of an air flow D 1000 m per hour for 20 to 60 A ratings D 2000 m per hour for 90 to
38. s supplying the load They must be mounted in the direction shown in the figure opposite Installing sensors The secondary terminals of the current sensors must be short circuited as soon as they are installed by placing the strap X1 in the MAINT position on the CCTY card The strap X1 will remain in the MAINT position until the MGE SineWave conditioner has been put into service see adjacent diagrams Connection Remove the CCTY card that is plugged into the TIFY card via the XR4 connector Turn the CCTY card over to connect the secondary terminals of the current sensors to the screw terminals XR1 XR2 and XR3 of this card Care must be taken to ensure that the phase order and polarity of the sensors are respected Once the connections have been made refit the CCTY card to the TIFY card Captor used if neutral connected Page 26 51027008EN BD Ne neutral load oo Po aea For a 20 A 30 A 45 A or 60 A unit Sf MERY board XR2 XR3 mm mm NORMAL MAINT CCTY board copper side phase 1 phase2 phase 3 CCTY board component side once removed and turned over Strap X1 for short short circuiting the current sensors phase 3 phase 2 phase 1 Installation cont SN they are installed by placing es the strap X1 in the MAINT W position on the CCTY card The strap X1 will remain in the MAINT pe position until the MGET SineWave phase 3 condi
39. service to intervene check the voltage at the conditioner inlet The voltage tolerances permitted are defined in the section on characteristics and performances check the frequency at the conditioner inlet The voltage tolerances permitted are defined in the section on characteristics and performances check ventilator operation the temperature inside the room and the cleanliness of the air vents The temperature tolerances permitted are defined in the section on characteristics and performances the conditioner is limiting current because the installation s compensation need is higher than the current that the conditioner can supply The conditioner automatically protects itself Compensation is not total Training centers Maintenance To allow you to useAPC by Schneider Electric products effectively and carry out basic maintenance we offer a complete range of technical training courses in English and French Training centers Schneider Critical Power amp cooling services 50 Hz France Training Centre 140 Avenue Jean Kuntzmann Innovall e 38334 St Ismier Cedex France Tel 33 0 4 76 18 34 14 Fax 33 0 4 76 18 45 21 Singapore Training Centre 10 Ang MO Kio Street 65 03 06 10 Techpoint Building Singapore 569059 Singapore Tel 65 6389 6792 China Training Centre No 999 Shen Fu Road Min Hang District Shanghai 201108 P R China Tel 86 21 3407 3365 Fax 86 21 3407 4526 Internet
40. st conductor subject to its effects Page 20 51027008EN BD 1 front protection plate lower protection plate PE PE neutral phase 3 Installation cont Connecting dry contacts and communication port optional Determining wiring Connection operations Procedure wiring is connected via the bottom in front of the device Signal cable connections AN must be mechanically fixed near the connectors so that any mechanical stress on the conductors is prevented configuration of dry contact terminal block gt 2 x voltage free changeover switches conditioner running stopped gt 1 x voltage free changeover switch current limiting operation connection to the terminal block may be made whilst MGE SineWave is operating these contacts comply with safe extra low voltage insulating requirements common conditioner stopped conditioner running common normal operation limiting operation common conditioner stopped conditioner running Contact breaking capacity P 2 P 2 VA U 30 V max J l 1Amax Remark Cross sectional Connector Type of recommended conductor area mm removable screw terminal block supplied male connector with female contacts on MGE SineWave the shielding must be connected at both ends dry contact terminal 0 5 mini multi core wires block 2 5 max not supplied shielded cable 9 poi
41. than 4 options the presence of the V symbol at the bottom of the screen indicates that the menu continues onto another screen The A arrow is used to move back up the menu Back view of terminal 3 9 point SUB D connector for connecting the terminal to the MGE SineWave conditioner RUN and STOP keys gt RUN conditioner local RUN command gt STOP conditioner local STOP command Operation cont The main menu offers Language available languages displayed The main menu is automatically displayed when the equipment is energized It can also be accessed from a sub menu by pressing ESC Language langue Principle measurements Secondary measurements oo several times Alarms Principle measurements r m s load and network THDI network voltage and MGE SineWave load rate displayed Configuration JBUS communication I Identification Reserved access Secondary measurements eS TE EEE detailed load and network current spectrum displayed Alarms alarms and level 1 diagnosis displayed faults acknowledged Configuration operating parameters modified JBUS communication communication port parameters modified Identification main conditioner characteristics and software versions displayed Reserved access access to APC by Schneider Electric personnel only Choice of language Press ESC several times if RS necessary to display the main menu gt Lang
42. this derating of 10 per additional 1000 m Configuration Display Commands Remote transfers Dimensions and weight colour reference standards electromagnetic compatibility Characteristics and performances cont language type of utility power sensor ratings reactive compensation remote RUN STOP confirmation choice or compensated orders communication parameters type of application number of parallel conditioners derating In relation to altitude utility power voltages automatic startup delay front panel display front panel keypad 3 voltage free changeover dry contacts height overall unit height width depth weight standard safety construction design protection conducted and radiated emissions testing and measuring techniques testing immunity to electrostatic discharges testing immunity to radiated fields testing immunity to fast transients voltage bursts testing immunity to surge voltage testing immunity to conducted disturbances induced by electrical radio fields gt French English German Italian Spanish Dutch American gt with or without Neutral gt closed sensors 300 1 500 1 1000 1 1500 1 2000 1 3000 1 4000 1 5000 1 6000 1 gt opening sensor 600 1 2000 1 gt Inductive Reactive gt Capacitive Reactive gt Inductive amp Capacitive Reactive gt
43. tioner has been put into service see adjacent diagrams The secondary terminals of For a 90 A or 120 A unit the current sensors must be short circuited as soon as i Ny Connection Remove the CCTY card that is plugged into the TIFY card via the XR4 connector Turn the CCTY card over to connect the secondary terminals of the current sensors to the screw terminals XR1 XR2 and XR3 of this card Care must be taken to ensure that the phase order and polarity of the sensors are respected Once the connections have been made refit the CCTY card to the TIFY card MERY board Strap X1 for short short circuiting the current sensors CCTY board NORMAL MAINT component CCTY board side once copper side removed and turned over phase 1 phase2 phase 3 phase 3 phase 2 phase 1 Captor used if neutral connected 51027008EN BD Page 27 Installation cont The secondary terminals of AN the current sensors must be short circuited as soon as they are installed by placing the strap X1 in the MAINT position on the CCTY card The strap X1 will remain in the MAINT position until the MGE SineWave conditioner has been put into service see adjacent diagrams Connection Remove the CCTY card that is plugged into the PARY card via the XR4 connector Turn the CCTY card over to connect the secondary terminals of the current sensors to the screw terminals XR1 XR2 and XR3 of this card
44. ty Isc short circuit current NS100 STR22SE 100 A 4p 3d magnetic threshold set at 2 x nom Page 12 51027008EN BD Installation cont 30 A MGET SineWave Table of recommended protections per rating Connection to the MGE SineWave terminal block where Pcu function of Isc Non distributed neutral Distributed neutral IT earthing system IT earthing system C60 3x40 A curve Z IT earthing system Vigi Compact NS100 STR22SE 40 A 4p 3d magnetic threshold set at 2 x nom neutral protection via Vigi sensitivity 10 A TT earthing system C60 3x40 A curve Z with Vigi C60 module TT earthing system Vigi Compact NS100 STR22SE 40 A 4p 3d magnetic threshold set at 2 x nom sensitivity depending on the installation TNC earthing system mo C60 3x40 A curve Z TNS earthing system Important upstream breaking devices should be set in AN such a way as to guarantee good discrimination with the circuit breakers recommended on this page Is 100A PE Key Is sizing current Pcu breaking capacity Isc short circuit current NS100 STR22SE 100 A 4p 3d magnetic threshold set at 2 x I nom 51027008EN BD Page 13 Installation cont 45 A MGET SineWave Table of recommended protections per rating Connection to the MGE SineWave terminal block where Pcu function of Isc Non distributed neutral Distributed neutral IT earthing system IT earthing system C60 3x63 A curve BIT earthing
45. uage langue Principle measurements Secondary measurements Alarms CHOICE OF LANGUAGE Configuration JBUS communication Identification Reserved access Nederlands Italiano US English 1 Choose the Language option using 8 Choose the language using the A the A and W keys The choice must and V keys and confirm via ENT be displayed in reverse video 2 Confirm the language option by pressing ENT Displaying main measurements Locating measurement points U I THDI U I THDI utility network deformed load to be compensated MGE SineWave 51027008EN BD Page 33 Operation cont Locating measurement points Using the main menu Press ESC several times if RY necessary to display the general menu The current measurements in 2 the neutral are not displayed in the case of a utility power without distributed neutral Insignificant measurements 9 are replaced by characters on the terminal screen and measurements where the capacity is exceeded are displayed with characters on the terminal screen gt Principle measurements Language langue Secondary measurements Alarms Configuration JBUS communication Identification Reserved access a ee ee eee 1 Choose the Principle measurements option using the A and W keys The choice must be displayed in reverse video 2 Confirm the Principle measurements optio
46. ufactured FRANCE through IS09001 process gt protection IEC 529 NFC 20010 gt electromagnetic compatibility EN 55011 class A gt susceptibility IEC 1000 4 1 IEC 1000 4 2 level 3 IEC 1000 4 3 level 3 IEC 1000 4 4 level 4 IEC 1000 4 5 level 3 IEC 1000 4 6 level 3 gt EC marking gt quality organisation 51027008EN BD Page 5 Principle Improvements offered by MGE SineWave The MGE SineWave active harmonics conditioner allows current distortion to be reduced and problems due to harmonics to be avoided e g gt unintentional tripping of protections owing to the value of current in the neutral gt cable heating notably in the neutral gt heating of generators transformers generator sets inverters etc gt standards on harmonics consumed on the utility power not being respected voltage distortion to be improved as Operating principle The current consumed by a non linear load e g a computer system is composed of a sinusoidal current IF which is a fundamental current at the utility power frequency and a harmonic current IH made up of currents having frequencies that are multiples of the network frequency The MGE SineWave conditioner continuously generates a current equal to IH so that the utility power current only has to supply the fundamental current The load MGE SineWave active harmonics conditioner assembly will then be seen by the util
47. um cable cross sectional areas can be determined based on the 9 sizing current Is given in the tables below It is advisable to connect the neutral when it is distributed Terminal block Diameter Maximum connection length of A areas mm capacity mm power cables Phases Neutral m 20 25 e 35 b J 30 4 9 e J 45 w po wo bB J 60 im wo o b w 90 10 50 70 20 per cui per cuiae ooo 120 16 70 8 20 per cubicle per cubicle MGE SineWave Recommended rating cross sectional 51027008EN BD Page 11 Installation cont 20 A MGE SineWave Table of recommended protections per rating Connection to the MGE SineWave terminal block where Pcu function of Isc Non distributed neutral Distributed neutral IT earthing system IT earthing system C60 3x32 A curve Z IT earthing system Vigi Compact NS100 STR22SE 40 A 4p 3d magnetic threshold set at 2 x nom neutral protection via Vigi sensitivity 10 A TT earthing system C60 3x32 A curve Z with Vigi C60 module TT earthing system Vigi Compact NS100 STR22SE 40 A 4p 3d magnetic threshold set at 2 x nom sensitivity depending on the installation TNC earthing system C60 3x32 A curve Z TNS earthing system Important upstream breaking devices should be set in AN such a way as to guarantee good discrimination with the circuit breakers recommended on this page Key Is sizing current Pcu breaking capaci
Download Pdf Manuals
Related Search