2015 Highway snow plough MSK03 user manual
Contents
1. 6 WARRANTY CONDITIONS The Seller gives the Product a guarantee for aterm of 12 twelve months The guarantee term starts upon delivery of the Product to the Buyer and the time of delivery is the date indicated in the deed of delivery and receipt or CMR The guarantee covers the elimination by the Seller of any production material or construction defects detected in the Product or details thereof during the guarantee period The Seller is obligated to replace the defective Product with a new one only if the repairing of the Product or a detail or replacing of a detail is not possible The Buyer undertakes to inform the Seller in writing of any defects detected during the guarantee term within seven 7 calendar days as of learning of the defect describing the defect in sufficient detail The Seller is obligated to carry out an expert assessment to identify the causes of the defect within fourteen 14 working days after the receipt of the written notice In the event of a defect covered by the guarantee the Seller eliminates it within twenty 20 working days after the expert assessment The performance of repair work under the guarantee takes place at the delivery address specified in the Order Confirmation Major repairs are made in the territory of the Seller The cost of transportation of the Product to the place of guarantee repairs is borne by the Buyer The Buyer bears the costs of repairs exceeding the terms and conditions of guara2. a pin since the pin is not designed to support this heavy loads and it will bend through 10 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 Drawing 6 Mounting and demounting of a plough Finnish fastening system Using the hydraulic support leg of the parallelogram In order to activate the hydraulic support leg the hydraulic supply system needs to be switched from lift cylinder control to support leg control This is done by using the switching valve on the parallelogram of the plough 1 Drawing 7 Turning the valve lever to the right towards the vehicle as shown in the drawing activates the lift cylinder turning the lever to the left activates the support leg of the parallelogram 11 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 Drawing 7 Switching valve 4 WORKING WITH THE PLOUGH The plough is provided with a lifting cylinder 1 Drawing 6 giving the plough an option of a mechanically floating position On the piston rod side of the cylinder there are control surfaces that enable the plough to move up and down float following the profile of the road surface In order to ensure floatability the weight of the plough shall not fall on the lifting cylinder but the cylinder shall be in a retracted position and free during work Before starting work check the pressure of the tyre if the machine is equipped with a support wheel The pressure must be 10 bar In the event of sharp temperature changes the t
3. device that is not in good technical condition Check that there are no people or objects near the snow plough that the plough might injure or damage In addition safety of people carrying out maintenance of the snow plough repairing the snow plough or moving it with the help of hydraulics or any other lifting mechanism has to be ensured Failure to follow safety requirements may result in causing injuries to people the snow plough is provided with safety markings see Drawing 5 It is prohibited to work under a lifted snow plough if the plough is not supported Check that the snow plough is properly fastened to the vehicle and the fasteners are not damaged Check the condition and visibility of safety marking position lamps if available and reflex reflectors Check the condition of the blades also the condition of sliding soleplates or wheels if available Worn blades must be adjusted downward turned around or replaced so as not to damage the blade holder Check the blade cotters Check the fasteners of levers and cylinders Check that the hydraulic hoses are intact and properly fastened Check that the snow plough is properly greased Check that the snow plough has no damages WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSK03 Working with the snow plough The snow plough may only be used by a person who is at least 18 years of age holds a driver s license in the respective category and has familiarised himself herself with th
4. support the mouldboard and prevent the blades from touching the ground when driving on soft ground WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 Drawing 4 Side support MSKO3 series is provided with a hydraulic side impact protection mechanism 7 Drawing 6 the function of which is to reduce shock impact on the blade tip in the event of contact with curbstones for instance The impact protection mechanism enables elastic turning of the plough skirting for up to 3 degrees when the rotational cylinders rods are at a distance of 50 100 mm from their extreme positions The plough is made of high strength steel For manufacturing the moldboard wear resistant special steel is also used The product is finished with high wear resistant paint MSK3703 MSK4003 MSK4603 Total width of the plough flap blades mm 3660 3965 4575 Plough flap working width at max swivel angle mm 2730 2950 3410 Total width of the plough flap mm 4370 4680 5300 Height of the plough flap in the right corner with blades mm 1530 1570 1620 Height of the plough flap in the left corner with blades mm 850 830 780 Maximum swivel angle both side 40 44 Angle of blades with respect to road surface 46 Total weight of the plough without blades and accessories 1074 1112 1190 kg Recommended operating pressure of the hydraulic system bar 160 200 Recommended output capacity of the hydraulic pump l min 3
5. the pin 2 of the lifting cylinder and store it in a holder Do not leave the pin attached to the cylinder during work The pin should only be used to mount and demount the plough If the pin is not removed for the work the plough will not follow the uneven profile the road and the pin may break You may leave the pin in place at your own responsibility only in the event the plough is equipped with a hydraulic floating system and the lifting cylinder does not press the plough against the ground Demounting of a plough from the truck or vehicle Drawing 6 Install the pin 2 in the control surface opening of the lifting cylinder 1 Place the plough on an even ground the cutting edge must rest on the ground and install the support leg 6 of the plough close to the ground approx 20 30 mm from the ground If you install the support leg completely against the ground when you demount the blade it is later more difficult to mount the blade on the vehicle the fastening plate of the plough will be positioned too vertically In the event of additional blades 8 it is recommended to lower the additional blades to the same plane as the front blade to ensure greater stability of the snow plough Loosen the fastening bolts or pins 5 of the frame of the vehicle Lift up the frame 3 of the plough from the frame of the vehicle with the help of the lifting cylinder Disconnect the hoses and drive further NB It is forbidden to lift up the plough with
6. the plough ensures economic efficiency and smooth operation even at speeds up to 70 km h The partially plastic flaps are less prone to rust than steel flaps they produce less noise and also weigh less Special cold and wear resistant plastic sheet is used for plastic material The snow plough marking indexes 3703 4003 and 4603 indicate the approximate total width of the plough s flap blades in millimetres MSKO3 series model is equipped with interchangeable blade holders with noise reducers Drawing 1 There isa 45 mm thick special cast rubber band 3 between the blade holder 1 and flap 2 which reduces noise and makes the movement of the blade 11 more elastic with respect to the road surface This in turn improves the quality of ploughing and protects the marking of the road surface from extensive wear and tear Blade holders are attached to the flap with fasteners 4 7 8 and 9 Elastic movement of the blade holder is ensured by aspherical washer 10 In order to prevent noise from transferring to the flap via bolts there are steel rubber bushings 5 6 in bolt openings The joints of the lifting frame parallelogram on the vehicle side are equipped with rubber bushings to further reduce further noise and vibration transferred to the cabin The blade is fixed to the blade holder as regular either with wedge bolts or other type of bolts In order to prevent the blade holder from wearing out too much when the blade wears away the
7. 0 50 Table 1 Technical specifications of the snow plough d WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 1 1 Highway snow plough in standard equipment Parallelogram lifting frame of the plough A moldboard with two rotation cylinders and a lifting cylinder 287 inch hoses with 2 inch quick couplers Replaceable side blades Safety marking and LED side lights Colour yellow RAL 1002 A hydraulic impact protection valve of the rotation cylinder with a hydraulic battery to reduce lateral impact 1 2 Accessory equipment Askid shoe with hard alloy plate and an adjustment mechanism A set of steel blades made of hard alloy or as per customer s request Hydraulic mechanism for the additional blade possibility to adjust blade pressure applied on the road surface A set of hydraulic skid shoe for lifting frame A set of hydraulic support leg A set of rubber cutting edges a special plough rubber with a thickness of 40 or 50 mm for the additional blade Electrical additional valve to control the additional blade if the vehicle is not provided with three pairs of hydraulic outlets NB For the additional blade the car needs to have three pairs of hydraulic spool valves or an additional valve for controlling the additional blade 2 SAFETY REQUIREMENTS FOR OPERATING THE SNOW PLOUGH Before operating the snow plough Check the integrity and technical condition of the snow plough It is prohibited to commence work with a
8. HIGHWAY SNOW PLOUGH MSK3 703 MSK4003 MSK4603 MEIREN ENGINEERING OU VAIKE MANNIKU 11216 TALLINN ESTONIA PHONE 372 682 5002 FAX 372 610 0589 EMAIL INFO MEIREN EE WWW MEIRENSNOW COM USER MANUAL 2015 This user manual applies for snow ploughs from serial number 089 1XXXXX MAREK Push your limits Expand your boundaries HIGHWAY SNOW PLOUGH MSKO3 CONTENT CE DECLARATION OF CONFORMITY isc ciccsciccscccssscacscsacsssesasecovecstsceuteovscenesecteseasa vacccuacsvacesdsensccesseuacessseccdveatsnd benes 3 FOREWORD eiccvisseccscsscsccsconscceucesstcuyd essiceeheasvuveosansedaacenseviaccesedebscesvenssecsavdenssausd sacesuncbeadcuteeontcetcecnseubeessacvebesssvvees 4 GENERAL SAFETY REQUIREMENTS iis sccscciscccsacsssscscscedtacssxesotccedsdssveasscadccsdesdenssvacddecedeassnadeasedecsceadenssvesdieceleaaseass 4 PERSONNEL jscsiscceccucctecsiessaeccssacadcessszscavacciaccduasssdaessacscaestuecaucesudccud ous esbesuancsasa uaacuvacsuaccadeews cevstaua ccusdtuacesuasiaaseaees 4 L PRODUCT DESCRIPTION i cscccscsscccsscsesccesseontcevesosscessessdcevatsessevencesdevsecensedeareseduscerstveevessavsessscaseescdsadesnaesetees 5 1 1 HIGHWAY SNOW PLOUGH IN STANDARD EQUIPMENT sci stqct sia dascecsy test alan dora antanhstaedountcaplessntonduateriacsiae aug leteteedse 8 1 2 ACCESSORY EQUIPMENT vrenin ia e AAE ATAA EAT A AAAA TAAA A TEAT A AAA T ia a raria 8 2 SAFETY REQUIREMENTS FOR OPERATING THE SNOW PLOUGH s eeeeese
9. bstacle the fastening bolts 4 Drawing 1 of the blade holder may break yet the structure itself will not get major damages and in most cases the plastic safety straps will keep the blade holder hanging on the blade 12 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 4 1 Transporting the snow plough MSKO3 series snow ploughs all have lifting eyes for transporting the plough marked with a corresponding marking Drawing 8 In order to transport the plough in cargo or a container first remove the screen 8 Drawing 6 to fit the plough into the cargo Drawing 8 Marking of the lifting eye 4 2 Usage of skid shoe The wheel or slide feet must be adjusted so that the steel cutting edge is 0 15 mm higher from the ground depending on the road surface The function of the wheel mechanism spring 2 Drawing 9 is to pull the wheel closer to the blade when it is in the transport position The tightness of the spring can be adjusted but the spring must not be this loose that the wheel gets in contact with the vehicle when the plough is lifted up Regarding the skid shoe it has to be verified that it does not wear off too quickly since the foot may break and fall off After adjustment of the wheel or skid shoe do not forget to install the handle splint 2 to ensure that the wheel or foot remains in the desired position Support wheels cannot be used with an additional blade 13 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 Drawing 9 U
10. de feet and wheels grease the regulating mechanism Spray the zinc coated parts hydraulic valves and hose ends with rust resistant wax Check the condition and fastening of the cutting edges If required adjust the cutting edges or replace these Check the condition and fastening of the cutting edges If required adjust the cutting edges or replace these Grease all grease points Also grease or wax the extended adjustment surfaces of the internal pipe of the wheel mechanism X X Check the plough visually and see if there are parts that need to be replaced Repair all paint damages Retract the piston rod of the cylinder and cover it with proper grease Store the plough in a place exposed to winds but protected from rain and UV rays Check that the hoses are pressure released Table 3 Maintenance plan of the snow plough WWW MEIRENSNOW COM 1 HIGHWAY SNOW PLOUGH MSKO3 Grease points 5 1 Drawing 14 Grease points gt KS o E a el o H bg Ka pun gg lal E else 2 8 3 3 clol S Elite o Elg so co a foi 9 slal S 2 Cl ZlOI iol Hl 8 a2 8 2 8 3 23 2 Oli ole S lt OC wl S Dn c el Oli o gt l p Hi a 2 olg lel OI Al ks on ol D ca g J Qe a 2 z a fo a D LU E om s EI a 18 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3
11. e operator s manual of the snow plough Make sure to always pay attention to the surrounding area and other traffic including vehicles approaching from side roads and behind Pay attention to pedestrians and cyclists so as not to put them in danger while working with the snow plough All warning lights must be switched on at all times while working Adhere to general traffic regulations The maximum operating speed for the snow plough in normal road conditions on hard paved roads is 70 km h Reduce speed when working on soft surfaces because the blades may cut into the ground the driver may lose control of the vehicle and the vehicle may run off the road If working on a soft surface the plough should be supported on sliding soleplates wheels or additional blades The snow plough may only be used to plough loose snow It is prohibited to plough ice frozen snowdrifts rocks gravel sand etc It is prohibited to plough snow banks at maximum operating speed since this may damage the snow plough The manufacturer shall not be liable for any damages caused by overloading the snow plough If the highway snow plough is used in the city or on uneven roads where there is risk of damaging the vehicle and road surface it will be done at the user s own liability The manufacturer shall not be liable for any damages caused by the abovementioned It is prohibited to attach such accessory equipment to the movable parts of the snow
12. for reimbursing losses GENERAL SAFETY REQUIREMENTS As the construction of the product is complex and it contains moving parts it is very important that the person working with the equipment be aware of all the safety risks To reduce the risks it is important that the operator have read through the operator manual the operator have been completed an appropriate training which gives him her the permit to use a product of this type in his her work the operator have been provided with all necessary tools and is wearing appropriate work clothes PERSONNEL This product may only be used and maintained by properly trained personnel The operator s employer is obliged to ensure fulfilment of all user instructions and safety requirements set out by the manufacturer Please read carefully through the operator s manual before starting working with the snow plough WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 1 PRODUCT DESCRIPTION Highway snow ploughs MSK3 03 MSK4003 and MSK4603 are durable snow ploughs with a conical steel frame partially plastic mouldboard and plastic screen intended for professional use on hard paved highways The blade angle of MSKO3 series snow ploughs with respect to the ground is 45 50 which ensures that snow is effectively removed from the pavement The conical mouldboard of MSKO3 series snow ploughs ensures greater snow discharge distance thus reducing the formation of snow walls The optimal shape of
13. ing 11 of the front blade To adjust the pressure remove the valve cap and adjust the pressure with an Allen by pressing at the same time the additional blade towards the ground or to the lower end position To increase the pressure in cylinders turn the screw clockwise The hydraulic system of the additional blade is equipped with two hydraulic batteries 2 Drawing 11 which ensure flexibility of the additional blade in the desired pressure conditions During adjusting you can use connection point 3 Drawing 10 of the pressure gauge to measure the pressure After flap adjustment the additional blade should be moved up and down to make sure it has been adjusted properly Its optimal pressure on the ground surface is listed in the table below The operating modes are recommended and they also depend on the road surface properties amount of salt used etc The driver should select the operating modes taking into account the local conditions and personal work experience When the road is uneven and plenty of salt is used the pressure of the additional blade should be raised 24 45 bar Drawing 11 Hydraulic unit of the additional blade Hydraulic system must be filled with hydraulic oil ISO VG 32 15 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 Recommended additional blade operating modes Additional blade s pressure on Additional blade s Weather conditions ground surface operating compared to frontal blade pre
14. ntee repairs and the transportation costs The following defects are not covered by the guarantee defects arising from the natural wear and tear of the Product defects arising from the characteristics or damages of the road cover defects arising from the use of the Product in conflict with its technical conditions security rules and purpose defects arising from disregarding the rules of maintenance of the Product defects arising from a traffic accident defects of which the Buyer has not informed the Seller in writing within seven 7 days as of the emergence of the defect and or whereby the Buyer has not given the Seller the chance to identify the cause of the defect in accordance with the Agreement tothe extent whose expansion the Buyer could have reasonably prevented The Product guarantee term terminates before the prescribed time as of the time when the Product has been independently repaired without coordinating it with the Seller in writing beforehand the constructions of the Product have been changed additional equipment has and or spare parts have been installed without coordinating it with the Seller in writing in advance If the Seller in spite of repeated written inquiries by the Buyer fails to perform its guarantee obligations arising from the Agreement the Buyer shall have the right to eliminate the Product s defect at the Seller s expense The Buyer must inform the Seller in
15. plough that the manufacturer has not approved Itis prohibited to use hydraulically operating devices as lifting jack The snow plough may only be lifted from lifting eyes Each time there is an incident during operation that may damage the equipment an inspection of the equipment shall be arranged in order to detect and assess possible damages Damages cracks in the structure or welded joints deformed parts may put property and people s health in danger It is prohibited to continue work until the damages are repaired Drawing 5 Safety marking RISK OF ACCIDENT WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 3 MOUNTING AND DEMOUNTING OF A PLOUGH Mounting of a plough on the truck or tractor Drawing 6 To mount the plough the vehicle must stand on a level surface Drive the vehicle as close to the lifting frame of the plough as possible and connect the hydraulic hoses to the quick coupler of the vehicle Lift the coupling frame of the plough to such a height that the fastening eyes 3 are over the upper edge of the coupling frame of the vehicle Drive the frame of the vehicle against the frame of the plough and lift the plough with lifting cylinders onto the frame of the vehicle Check that the fastening eyes 3 are correctly positioned and lock the frame 5 of the plough on the frame of the vehicle as the locking systems of ploughs may differ depending on the country please follow the applicable requirements Remove
16. re are wear resistant steel support plates underneath the blade holder which decrease the speed in which the blade holder wears away these are not designed to be used as a Sliding soleplate K Drawing 1 Fastening of the blade holder This plough type differs from ploughs made by other manufacturers by a special fastening method of the blade to the lifting frame parallelogram We use a spherical slide bearing which ensures turning of the blade with a cylinder as well as lateral tilting of the plough when the inclination of the road changes For this purpose there is a polyurethane axle pad 1 Drawing 2 installed in the upper part of the rotation axle of the blade This axle pad ensures tilting of the blade approximately two degrees in both directions during work following the road profile and when lifted up the axle pad prevents excessive swinging of the blade The axle pad also reduces vibration generated during the plough work 5 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 Drawing 2 Rotation axle of the blade The right side of the moldboard is equipped with replaceable side blade 1 Drawing 3 which simplify cleaning of curbstones of the pavement The edges of the side blades are reinforced with hard alloy coating round profiles which ensure smooth shock free cleaning of curbstones Drawing 3 Side blade The left side of the mouldboard is equipped with a replaceable side support 1 Drawing Al that is designed to
17. s the red area Hardox rubber blade wear must not exceed the red line i e 70 mm on both sides 16 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 5 MAINTENANCE Drawing 13 Hardox rubber blade MAINTENANCE IN EVERY 8 WORKING HOURS MAINTENANCE IN EVERY 150 WORKING HOURS MAJOR SEASONAL MAINTENANCE Check all bolt connections and hydraulic connections and tighten if required Check all bolt connections and tighten if required Check all bolt connections and tighten if required If the plough is provided with wheels check the bearing play of the wheels see the spare parts catalogue Drawing 6 If the play is too big disassemble the wheel hub 10 check the bearings 30 and adjust the play for adjusting use a nut 25 and a special locking washer 24 with pegs Check the condition of the fastening bolts of the blade holders The bolt 4 Drawing 1 torque must be approximately 60 Before tightening and controlling loosen the locknut Check that there are no leakages in the hydraulic system If required tighten the connections of the hydraulic parts and hose ends Check that there are no leakages in the hydraulic system If required tighten the connections of the hydraulic parts and hose ends Grease all grease points bearings of the rotation and lifting cylinder of the blade for Norwegian and Danish fastenings also the bearing of the coupling frame If the plough is provided with sli
18. sage of the skid shoe 4 3 Working with an additional blade MSKO3 series snow ploughs may be equipped with a hydraulic blade additional equipment which gives better and cleaner ploughing result In certain weather conditions sleet and wet snow it is only permitted to use an additional blade whereas the front blade must be lifted up from the ground The additional blade can be equipped with a rubber blade with the thickness of 40 50 mm and made of special rubber mix The blade holder has a mounting plate 1 Drawing 9 for attaching the rubber strap the rubber sheet is pressed to the mounting plate with the help of bolts 2 When you use such fastening method there is no need to make bolt openings in the rubber blades Compared to the products made by competitors it takes much less time to replace the rubber blades of this type of a plough It is also possible to lower the worn blade which enables maximum use of the entire wearing material 14 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 Drawing 10 Additional blade Adjustment of working pressure of the additional blade For installing a hydraulic additional blade LH the vehicle must be equipped with three distributor sections six quick coupler parts The capacity of the hydraulic pump must not exceed 50 l min since otherwise the blade will move too fast up and down With the help of hydraulic cylinders of the additional blade it is possible to lift up the pressure valve 1 Draw
19. sseesesesessosseseseesosseseseeseeseressesseseseesee 8 3 MOUNTING AND DEMOUNTING OF A PLOUGH tccccesscseesecnsseseeseessecssesssseessssssessessssssesseaseeeees 10 A WORKING WITH THE PLOUGH cciccs cccscs scccsicsscccevsecccsaccsoccsecesnsesoucesatcstees sccdvecenstsessessanansencsdeccencestacons es 12 Sch TRANSPORTING THE SNOW PLOUGH ee ebe ee ee te 13 Ao USAGE OF SKID SHOE tele 13 A WORKING WITHAN ADDIMONAL BUADE ut 14 4 4 DESCRIPTION AND USE OF HARDOX RUBBER BAD eeenes rer Sed Ad edteede eegene 16 Be MAINTENANCE ees ee deed Ee 17 Sels MGREASEPOINTS zeini R A EE 18 6 OT IR EU II KEE 19 TABELS Table 1 Technical specifications of the SNOW plough AN d Table 2 MSK series recommended working modes for the additional blade EEN 16 Table 3 Maintenance plan of the SNOW plougb ee esesseseseeseseeesesesscsesesscsesecucnecusscsesucucnecusscsesucucsesesscaesusacaesesecseeuenseesecacaneeenees 1 DRAWINGS Drawing 1 Fastening of the blade Kolder EENS 5 Drawing c Rotation axlecof the pade aiar eaa a EA eae see ae oe ee as a rae 6 DRAWING Elter censeo 6 Drawing Sid SUpport eenegen deed d Hrawpe bh Safety markingsRISK OF ACHEN Hesse edel Aeddi 9 Drawing 6 Mounting and demounting of a plough Finnish fastening sustem 11 Urawitgce Sweet ehre leede Ee 12 Drawing 3 Marking ofthe lifting CUS sanansa e A EA EEE EE E A E 13 Drawing S Usage of the SkId SHOG ia ea A N E E EE E ONE 14 Drawing tO Additional blade ia sivccsi
20. ssure bar 100 Wet snow snow layer 2 3 cm raise the frontal blade from 60 90 the surface Wet snow snow layer 4 5 em 60 90 30 45 temperature range from 1 C to 1 C Loose snow 3 7 cm i 30 70 20 35 temperature range from 15 to 0 C Compacted snow ice 7 er 0 0 temperature range from 25 to 0 C Table 2 MSK series recommended working modes for the additional blade When the additional blade s flap pressure is set to 40 45 bar thus raising the frontal blade from the surface the additional blade can be pressed down in a weaker manner maintaining the contact of the frontal blade with the surface The success of this depends on the driver s skills it is not a precise operation and may not ensure the desired pressure distribution between the frontal and rear blades Drawing 12 Manometer 4 4 Description and use of Hardox rubber blades Hardox rubber blades are highly durable rubber blades with Hardox metal reinforcement that withstand difficult conditions better than standard rubber blades and ensure significantly longer lifetime thanks to wear resistant metal Hardox blade is suitable for use instead of rubber blade with all snow ploughs Hardox rubber blade includes steel blade segments surrounded by rubber Hardox rubber blade can be used on both sides up to the red area marked on the blade If one side of the blade is worn out up to the red area turn the blade over and use the other side until it reache
21. tiscansutinigiistia asepetaeeansentianeanlesnbie diate EE OE SAAE NETS N SKE SOE Nane 15 Drawing 11 Hydraulic unit of the additional blade EEN 15 Drawing t2 MAO MMC maese nisitan e ii 16 Drawing 13chlardox rubber biade edain ET E R ena oi anew E EE 17 Drawing 14 Grease EE 18 WWW MEIRENSNOW COM CE DECLARATION OF CONFORMITY Manufacturer Meiren Engineering OU Vaike Manniku 7 11216 Tallinn Phone 372 682 5002 www meirensnow com We hereby declare that the below mentioned product Highway snow plough MEIREN vw SK Model Serial number Manufacturing date Meets the following directives and standards 2006 42 EC EN 349 1993 A1 2008 WWW MEIRENSNOW COM HIGHWAY SNOW PLOUGH MSKO3 HIGHWAY SNOW PLOUGH MSKO3 FOREWORD Thank you for choosing the Meiren Snow product This operator manual consists of technical specifications user and maintenance instructions and warranty terms and conditions of MSKO3 series snow plough MSKO3 series snow ploughs are designed for removing loose snow from surfaced roads The product is not suitable for removing sand gravel ice or other similar material Using the plough contrary to its intended purpose may cause economic losses and bodily injuries It is therefore of the utmost importance that the person operating the plough read through the manual and use the product pursuant to the requirements Any misuse of the product releases the manufacturer from the liability for occurred damages and
22. writing at least five 5 working days before the replacement or repairing of a defective Product and submit to the Seller a calculation of the presumable reasonable costs The Buyer may withdraw from the Agreement and demand that the Product be taken back and the Purchase Price refunded only if the defect cannot be eliminate or the part cannot be replaced and if replacement of the defective Product with a new Product would not produce the results that would allow for the purposeful use of the Product The Product or a part thereof replaced during the guarantee term is covered by the guarantee until the expiry of the overall guarantee term of the Product 19 WWW MEIRENSNOW COM
23. yre pressure has to be re checked It is very important to use proper working methods and not to overload the plough For removing thick and heavy snow choose suitable slow speed and pay constant attention to the consistency of the snow For removing wet snow and sleet make more use of the additional blade made of rubber The pressure of the additional blade of the MSK series ploughs may only be adjusted when the front steel blade is in no contact with the ground surface Yet the additional plough may still get clogged when the front blades are too high up from the ground and the additional blade must remove all the snow Do not use the additional blade on dry asphalt since it may cause jerky movement of the plough and the additional blade may wear off too quickly On ploughs equipped with a rubber additional blade we recommend to use hard alloy blades since these are more wear resistant On models with slide feet also standard steel blades may be used if the weight of the plough does not fall on the blades It is not recommended to fully retract or extend the rotation cylinder during work Approx 100 mm has to be left for the cylinder travel In this way it is possible to use the safety valve of the rotation cylinder to reduce more efficiently impacts of possible obstacles If the plough is driven against an obstacle with a side the rotation cylinder in the end position may damage the plough and the vehicle In case the plough is driven on a rigid o
Download Pdf Manuals
Related Search