USER MANUAL - Mega Systems
Contents
1. or for unauthorized repairs or parts This warranty gives you specific legal rights and you may also have other rights which vary from state to state Mega Lite 5718 Kenwick St San Antonio TX 78238 Ph 210 684 2600 Fax 210 855 6279 www mega lite com info mega lite com2. your product is covered by a one year parts and labor limited warranty LEDs are not guaranteed to match in color temperature or output It is the owner s responsibility to furnish receipts or invoices for verification of purchase date and reseller or distributor If purchase date cannot be provided date of manufacture will be used to determine warranty period Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of the original invoice and Return Authorization Number given by MSI Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical means of shipment Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer MEGA SYSTEMS INC makes no warranties express or implied with respect to any product and Mega Systems specifically disclaims any warranty of merchantability or fitness for a particular purpose Mega Systems shall not be liable for any indirect inci dental or consequential damage including lost profit sustained or incurred in connection with any product or caused by product defect or the partial or total failure of any product regardless of the form of action weather in contract tort including negligence strict liability or otherwise and weather or not such damage was foreseen or unforeseen Warranty is void if the product is misused damaged modified in any way
3. MEGAG X 1 TP OUutshHiNewwoo Ka USER MANUAL Table of Contents Safety Information Specifications Main Power Connection DMX 512 Connection Main Control Menu DMX Profile Rigging the Fixture Cleaning amp Maintenance Parts List OOOM0ODUIMNRD Check that the unit has not been damaged during transport Read all cautions and warnings prior to operation of this equipment Protection Against Fire Fire Maintain a minimum of 1 foot distance from any type of flame Replace fuse only with the specified type and rating Do Not install the unit to close to a heat source Make sure cable are properly secured Maximum surface operating temperature 140 pre Protection Against Fire 1 Disconnect power before servicing 2 For connection to main power supply proceed to page 5 3 This unit must be earthed electronically grounded Electrical Protection Against Mechanical Hazards 1 Use safety chain when hanging unit ak 2 Use quality clamps or bolts when positioning unit 3 Do not open unit while it is on risk of electrical shock Mechanical Technical Information Part Numbers 7202 Outshine WW100 Mechanical Specifications DMX Connectors Neutrik X HD Series 3 or 5 pin IP 65 Rated XLR connectors in and out Thermal Maximum ambient temperature 104 Maximum surface temperature 140 Fastening System Double Mounting Yoke 1 65 Display Digital Power connection Cable Adap
4. e desired sped use the up down keys 15 options confirm the settings E Flash This function allows you to select a preprogrammed strobe sequences Press Enter use the up down keys to select de Press Enter sired strobe program 15 options Press Enter to set the desired sped use the up down keys 15 options to confirm the settings TI M i i LI tl Dimming Speed Press Enter to select the desired dimming speed when used with a DMX controler Use the up down keys to select from 0 to 3 0 speed will be the fastest 4 will be the slowest Press Enter to confirm DMX Profile Outshine WW 100 Mode A Outshine WW 100 Mode P Outshine WW 100 Mode H Rigging the fixture Caution 1 The installations must be carried out by an authorized dealer or trained profes sional 2 Unit may cause severe injures if you have doubts concerning the safety do not install When rigging a unit it is very important that you follow common safety procedures Rigging requires extensive experi ence including but not limited to calculating working loads material being used and periodic safety inspections If you lack these qualifications do not attempt the installation yourself instead use a professional structural rigger When rigging the unit always be secured with a secondary safety attachment The installation location of the fixture has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming Installati
5. et the unit operate from 100V to 240V from 50Hz to 60Hz Cable USA Cable EU 110V 220V N L Unit is equipped with cable mounted Neutrik Power Connections Female NAC3FX W amp Male NAC3MX W P P DMX 512 Connection The fixture is equipped with 3 or 5 pin cable mounted XLR for DMX input and output The sockets are wired in parallel Only use a shielded twisted pair cable designed for RS 485 and 3 or 5 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another Unit also ships with a Male Nema 5 15 to Female NAC3FX W adaptor DMX input DMX output 1 Shield a 2 Signal ar 3 Signal r 4 N A 5 N A Caution At the last fixture the DMX signal needs to be terminated with a terminator Solder a 120 Ohm resistor between the and the signal into a 3 pin XLR plug and plug it in to the last fixture on the signal run Pre manufactured terminator plugs are avail able for purchase from your Mega Lite dealer P DMXT Display Menu The control board on the fixture base is your interface to access and control all the functions on the unit Its digital display gives you a code view of the options and functions The following will explain each func tion and its options Menu Enter Up Down DMX Address A Mode 3 Channels P Mode 4 Channels H Mode 6 Channels _I Ti TI l I I as 001 512 001 512 001 512 Set Color Warm White Dimmer mi
6. on should be checked at least one time a year by a skilled person Cleaning and maintenance Installation Maintenance The operator has to make sure that the unit is operating safely and has the installa tions and electronics checked by an expert every year The following points have to be considered during the inspection 1 All screws used for installing the device or part of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing fixation and installation spots ceiling suspension trussing 3 The electronic power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed Note There is no serviceable parts inside the device except for the LED s Maintenance and service operations are to be carried out by authorized dealers Replacing the fuse Only replace the fuse with the same type and rating Replacing the power cable If the power cable of this device becomes damaged it has to be replaced by author ized dealers or trained professional only Should you have further questions please contact your dealer Parts List Accessory 7200 35 35 degree lens 7200 KNOB Knob Set 7202 LED LED Replacement Warranty Information Warranty Conditions Unless otherwise stated in writing
7. t All H 0 255 Effects WW Fade Up N A N A N A N A WW Fade Down Ta Is E Gu 1 EE Guy NG Gr NT Eirin eae came IM Gid Gir Moc mPa PI Pe see ea ae Speed 0 15 N A WW Fade WW FadeD WW Fade U On Off Random On Off Foamy tyro ra DE awe Ed I FNH ry FN INTE ER SIER 19 FA 19 0 15 0 15 0 15 0 15 0 15 Flash WW Strobe N A N A N A N A WW Strobe N A Strobe Strobe FI OG Et MI ED MI ID ul dO ID ME Er Fey Wes Pia 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 Strobe Step Strobe Pausing Strobe On and Strobe Dim and Strobe Random Strobe EI I EI I LI _ 1 IL Ed I 0 15 0 15 0 15 0 15 0 15 0 15 Dimming Speed IN Ei ti 1 0 1 2 3 N DMX Address TI TT dl I Press Enter to select the DMX start address channel The first display will let you Know what operation mode you are in Use the up down keys to select the desired mode Press Enter to confirm first Letter will also change depending on what mode you are in Use the up down keys to select the desired start address press Enter to confirm Set Color Menu Press Enter to set a Dim via display control Use the up down keys to select the desired intensity you would like to adjust Press Enter to confirm Use the up down keys to select the desired intensity of the LED Press Enter to confirm ELLE LILI Fade This function allows you to select a preprogrammed fade sequences Press Enter use the up down keys to select de Press Enter to sired fade program 15 options Press Enter to set th
8. ter Mounted Nema 5 15 to Neutrik True Power Out NAC3FX W Fixture Cable mounted In and Out Neutrik IP 65 NAC3FX W amp NAC3MX W Size 11 25 x 11 25 x 10 5 Size 10 x 10 x 15 Weight 13Ib Weight 15lb Electrical Specifications LED Quantity 1 Warm White COB LED Refresh Rate 1200 Hz LED Watts 100W LED Lifetime 60 to 100 thousand hours Power Input Voltage 110V 240 50 60 Hz Beam Angle 52 Ballast Electronic auto switching Field Angle 118 Power Consumption Watts 69 Amps 72 CRI 97 Control amp Programming DMX 512 Protocol DMX Modes Mode A 1 Channels On Off Mode P 1 Channels Dimmer Mode H 2 Channels Dimmer Strobe Control Options Display preset setting Ordering Options Item Number LED Color Lens Angle Fixture Color 7200 T 100 RGB Red Green Blue 35 35 BLK Black 7201 VW 100 Variable White 52 52 WHI White 7202 VWW 100 Warm White XXXX Custom 7203 cw 100 C Cool White DMX In Out il l Neutrik IP 65 3 pin in and out Neutrik IP 65 5 pin in and out elil Main Power Connection Caution Do not connect fixture to a dimmer system This unit has Auto switching power supply It will respond to 110V or 220V automatically This unit must be earthed electronically grounded Replace fuse only with the specified type and rating The occupation of the connection cable is as follows This fixture is equipped with an electronic power supply that will l
Download Pdf Manuals
Related Search