1446131092_UserMan DMAC-9M-7M
Contents
1. 10 27 15 Page 3 of 12 Author CNR Dakota Mero Inc DMAC 7M 9M C1 C2 User Manual C Suggestions for Camera Mounting o When determining the location for the camera it is always best to use a solid surface to minimize vibration o Important Ladders are not good mounting choices due to lack of stability o Ifyou will be using your AgCam for assisting in visibility for towing you will want to position the camera so you can see the desired area and a portion of the vehicle trailer in tow this will give you some reference to distance You will also want to use the mirrored setting in the monitor menu or remove the magnet in the MIR function plug on the camera so as to accurately represent left and right This will give you the effect of looking in a rear view mirror V CAMERA WARNINGS A NEVER RELY ON YOUR AGCAM AS A SAFETY FEATURE It is up to your discretion to keep your road travel and other operations safe Your AgCam will provide you with information only based on what it sees Operation of machinery safety guidelines still apply B The AgCam is equipped with an array of infrared light emitters which are invisible to the human eye This feature will aid in low light conditions but has limitations The effective range of the night vision feature is 1 to 45 feet and will produce a monochrome image only DO NOT ATTEMPT TO DRIVE MACHINERY USING THIS FEATURE Vi CABLE ROUTING TIPS amp WARNINGS There are two 2 lengths of2. Enables timer that will turn off monitor GRID Superimpose a grid on screen Aspect Ratio adjustment normal wide SEL Chooses the highlighted selection in MENU DMAC 7M 9M C1 C2 User Manua REMOTE CONTROL Press the MENU key on the monitor or remote Use the and keys on the monitor or the Left and Right arrow keys on the remote to move through the icons at the top of the screen 1 Use the MENU key on the monitor up and down arrows on remote to select an item under each section Selected menu items turn red 2 Use or on the monitor left and right arrows on remote to change the value of the highlighted item 3 To exit a b Rev 10 27 15 Page 7 of 12 Press the or key on the monitor left or right arrow on remote multiple times until the menu goes away Allow monitor to time out approximately 5 seconds Author CNR Dakota Mire Inc DMAC 7M 9M C1 C2 User Manual PICTURE BRIGHT Adjusts the brightness of the image CONTRAST Adjusts the contrast of the image COLOR Adjusts the color of the image TINT Adjust tint of image appears only when camera is plugged in COLOR RESET Returns settings to default TINT RESET PICTURE bs P ES BRIGHT CONTRAST VOLUME VOLUME Paik a VOLUME Adjusts the volume level OPTION oe ll 1 Se UTR a il fee ky E CAMERA 1 AV1 event trigger delay time CAMERA 2 AV2 event trigger delay time CAMERA 3 AV3 event trigg
3. when used in situations outside of the above mentioned parameters We always request that customers keep in mind that our less expensive OverView product line is cheaper because it does not feature the reliability and durability of our AgCam and EnduraCam lines The warranty available on these products reflect that durability e To avoid electrical shock and maintain optimal functionality do not open the enclosures High voltage may be present and there are no user serviceable parts inside All warranties will be void should any enclosures be tampered with in any way e Do not use any harsh chemical solvents cleaning agents or corrosive detergent to clean away dirt on the surface of the screen or lens e On AgCam and EnduraCam products the photo chromic camera lenses have been made impact resistant and have been drop ball tested according to Sec 3 84 21 CRF BUT ARE NOT UNBREAKABLE Because they have been hardened chemically they show no stress pattern Inspect your lenses frequently Chipped or scratched surfaces will reduce protection Such lenses should be replaced only by the manufacturer e Power to cameras is not interrupted by turning off monitor 12v power source must be terminated when not in use to avoid battery drain To avoid this problem be sure when hard wiring a unit use a fused circuit e Do not use your Dakota Micro camera system for anything other than legal surveillance and observation uses Dakota Micro Inc is not liable for an
4. Dakota Mero mc Users Manual AgCam 7 or 9 Monitor Single or Double Camera Kit Part Number DMAC 7M 9M C1 C2 3 qo12Y a qoufosd O a z ajqodn VI VII VIII Xl XII XIII XIV XV XVI XVII XVIII Table of Contents Included Monitor Kit Components 2 Standard Features 2 3 A Cameras 2 B Monitors 3 C Cables 3 Parts of an AgCam 3 Camera Mounting 3 4 Camera Warnings 4 Cable Routing Tips amp Warnings 4 Monitor Installation amp Mounting 4 5 Installation 5 Power 5 Event Trigger Wire Operations 6 A Event Trigger Wire Color Guide 6 B Event Trigger Wires Explained 6 Monitor Remote Operations 6 7 A Monitor Operations Front 6 B Remote Operations 7 Menu Settings 8 9 Specifications 10 Warnings 11 Product Warranty Repair Process 11 Consumer Limited Warranty 12 Disclaimer 12 Contact Us 12 Always read the manual prior to operating this equipment Also please follow all safety signs and precautions See the Dakota Micro Inc website for installation training videos at www dakotamicro com Rev 10 27 15 Page 1 of 12 Author CNR DMAC 7M 9M C1 C2 User Manual I INCLUDED MONITOR KIT COMPONENTS PER PN DMAC 7 9M Description Picture Dakota Micro Inc 7 or 9 Monitor Monitor Wire Harness PN DMAC MWH Monitor Remote PN DMAC REMOTE styles vary by kit amp battery is included A C Power Wall Plug PN DMAC PA styles vary by kit Moni
5. Micro Inc warrants that the Product will be free from defects in material and workmanship for periods as stated hereafter from the date of original purchase THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS THE EXCLUSIVE REMEDY OF THE BUYER IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT EXCEPT AS STATED IN THIS WARRANTY DAKOTA MICRO SHALL NOT BE LIABLE FOR ANY LOSS INCONVENIENCE OR DAMAGE INCLUDING DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OR INABILITY TO USE THE PRODUCT WHETHER RESULTING FROM BREACH OF WARRANTY NEGLIGENCE STRICT LIABILITY OF ANY OTHER LEGAL THEORY Any oral statements or representations made by anyone which are contrary to or at variance with the terms stated in this LIMITED WARRANTY are void Dakota Micro will at its option either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period of three 3 years for AgCam EnduraCam cameras two 2 years for AgCam EnduraCam monitors quads and Wireless components Twelve Months 12 for all Overview Cameras amp Monitors and one 1 year for Mini DVR cables and all other accessories The Dakota Micro limited warranty periods outlined above apply throughout the United States and Canada only A one 1 year maximum limi
6. cable that come standard with our AgCam camera kits One 1 20 and one 1 60 If you would like to purchase different or additional cable lengths please contact your local AgCam dealer A Cable routing is important where you choose to run the cables should not interfere with the normal operation of the machine or any safety equipment B ALWAYS be aware of any pinch points or other potential hazards to the cable s C Secure all cables to vehicle equipment using cable clips zip ties or other style fasteners D If you intend to use your AgCam for short length PTO operated implement avoid excess cable lengths if possible When you decide on a location you should fix the camera to a permanent bracket using inch bolts and attach any loose cable securely so there is no chance of entanglement in the PTO or other moving parts E If you use your AgCam to monitor a combine hopper or other combine operations take care to remember that combines have many moving parts Use extreme care when routing cables and it is strongly recommended that you use bolts to secure the camera While it would be sufficient to use the magnetic base for monitoring purposes during road travel it is advised to secure the camera with bolts during operation of the combine Vil MONITOR INSTALLATION amp MOUNTING A Mounting Precautions Remove your monitor carefully from packaging and inspect all mounting hardware Mounting location is the most
7. ction plugs utilize a polarized magnet to change camera functionality e IR ON OFF This function plug requires a magnet to allow for the IR LED s to function in low light conditions If you remove the polarized magnet the IR LED s will NOT come on e MIR FOR This function requires a magnet to activate deactivate the mirror forward function of the camera Elite cameras are shipped from the factory with the MIR magnet installed IV CAMERA MOUNTING After camera is securely mounted plug the camera pigtail into rear of AgCam camera You can now plug the remaining end of the pigtail into your power video extension cable Make sure the extension cables are securely attached and locked turn will lock the cables together A Temporary Mounting o Fortemporary mounting it is recommended that you use the supplied 65 pull magnet If using magnetic mount fasten camera cable with a zip tie or other style fastener This will act as a safety wire in the event your camera is knocked loose for some reason When selecting a location make sure that the equipment surface is clean of all foreign material and as flat as possible to ensure that the magnetic camera base will have good contact and not vibrate off The thicker the metal base the more securely your magnet will hold B Permanent Mounting o For permanent mounting it is recommended that you remove the magnet and attach the camera bracket to any solid surface with two 2 screws Rev
8. er delay time CAMERA 4 AV4 event trigger delay time ROTATE Inverts image on screen ROTATE Rev 10 27 15 Page 8 of 12 Author CNR Dakota Mire Inc DMAC 7M 9M C1 C2 User Manual SYSTEM oYSTEM a 25 fe red LANG ENGLISH LANG Select your language English default SOURCE AVI SOURCE Adjusts the AV input source AV1 default GUIDE LINES OFF GUIDE LINES Super imposes a grid on your monitor screen select ON or OFF PRESET PR SLEEP Enables sleep timer delay setting in minutes AV1 Enable ON or Disable OFF AV1 AV2 Enable ON or Disable OFF AV2 AV3 Enable ON or Disable OFF AV3 AV4 Enable ON or Disable OFF AV4 VGA Enable ON or Disable OFF VGA input Rev 10 27 15 Page 9 of 12 Author CNR Dakota Mero Inc DMAC 7M 9M C1 C2 User Manual XIII SPECIFICATIONS 45 F 150 F 42 C 66 C Waterproofingcriteria POD 9 16 9 digital panel 7 16 9 digital panel Min 12v Check monitor label for specific voltage range Rev 10 27 15 Page 10 of 12 Author CNR Dakota Mero Inc DMAC 7M 9M C1 C2 User Manual XIV WARNINGS e When selecting a camera system from Dakota Micro be sure to utilize the appropriate system for your use AgCam and EnduraCam cameras are designed for high impact moisture vibration and a variety of other rough conditions OverView cameras and kit components are designed for light use low vibration and low moisture OverView equipment is not warranted
9. ere caused by repairs or attempted repairs performed by anyone other than Dakota Micro Some states do not allow the limitation or exclusion of incidental or consequential damages so said limitation may not apply to you Any action at law suit in equity or other judicial proceeding for the enforcement of any right provided for herein or otherwise or with respect to any claim that a purchaser may have against Dakota Micro shall be instituted only in the Courts of the State of North Dakota either in the state district court located in Wahpeton North Dakota or in Federal District Court location in Fargo North Dakota Without regard to conflicts of law principles the laws of the state of North Dakota shall govern the interpretation and enforcement of the terms of this Limited Warranty and all aspects of the relationship between Dakota Micro and the purchaser This warranty gives you specific legal rights and you may also have other rights which may vary from state to state XVII DISCLAIMER Dakota Micro Inc products specifications pricing and programs are subject to change without prior notice Dakota Micro Inc reserves the right to make design changes at any time without obligation to retroactively install them on previously sold units XVIII CONTACT US Dakota Mero tne 8659 148th Ave SE Cayuga ND 58013 www dakotamicro com Rev 10 27 15 Page 12 of 12 Author CNR
10. important part of the monitor installation as it ensures you the maximum visual benefit from your AgCam system With that said when installing your monitor ensure to follow these three 3 precautions 1 The monitor is out of direct sunlight This will prolong the life of the unit as well as ensure optimum visibility 2 The monitor does not obstruct view 3 The monitor does not interfere with the normal operation of equipment WARNING Dakota Micro Inc is not responsible for any damages caused to your monitor or yourself due to the improper installation or use of a suction cup monitor mount whether it be product sold by DM or product purchased from another source Rev 10 27 15 Page 4 of 12 Author CNR Dakota Mire Inc DMAC 7M 9M C1 C2 User Manual B Universal Bracket Mounting 1 Hold monitor U bracket in place on monitor 2 Attach bracket with included wing bolts C Finalizing Universal Bracket Installation 1 With the mount and monitor attached find and mark the desired position for the monitor 2 Remove the monitor from the mount 3 Attach the monitor to the mount and tighten the wing nuts Vill INSTALLATION A Monitor Wire Harness Details 1 Input to Monitor 2 AV1 4 Event Trigger Wires Pg 6 Power Input RCA Video Output AV1 Audio Video Input 3 4 AV2 Audio Video Input y j AV3 Audio Video Input r AV4 Audio Video Input IX POWER A Supplying Power with 12v Power Adaptor 1 At
11. kota Micro Inc RA XXXXX 8659 148th Ave SE Cayuga ND 58013 6 Upon receipt and evaluation of product at Dakota Micro Factory it will be established if the repair is warranty or non warranty If requested customer will be called and notified of any applicable charges 7 Ifthe repairs are deemed non warranty and require a service repair fee of any kind a credit card number will be requested by Order Processing after the repair is completed 8 If customer is unable to be contacted over the course of 3 weeks regarding required non warranty repairs product will be returned unrepaired to the customer 9 Any product returned without proper documentation may be returned at customer s expense 10 Product returned with unconfirmed problems will be assessed a S60 evaluation fee per unit 11 Return shipping costs will be borne by the party at fault in other words if Dakota Micro determines that the defective product was covered under warranty Dakota Micro pays the shipping charges If Dakota Micro determines that it was the customers fault the customer will pay shipping charges If a particular circumstance cannot be determined than the cost of shipping charges will be decided on a discretionary basis depending on the situation at hand Rev 10 27 15 Page 11 of 12 Author CNR Dakota Mero Inc DMAC 7M 9M C1 C2 User Manual XVI CONSUMER LIMITED WARRANTY Subject to the disclaimer limitations and other directions stated hereafter Dakota
12. positive output 10 5v to 16 9v switch or supply to cause the monitor to automatically switch the unit to its respective channel camera Example if you were to attach the AV1 wire to a positive output from an unloading auger on a combine the monitor would switch from channel 2 3 or 4 to channel 1 when the auger is extended The event circuit should be neutral in its normal state and change to HIGH 12v when the event is considered to be active XI REMOTE amp MONITOR OPERATION A 7 or 9 Monitor Operations Front 1 3 FOR USE ONLY WITH Quad Processor Headphone Jack Output for audio available only on 9 Models Full Screen When connected to DM Quad will show cameras 1 2 3 4 each time pressed Duplex Screen When connected to DM Quad will show Camera 1 4 and camera 2 3 each time pressed When connected to DM Quad will display all 4 cameras connected ice aaa TOE E ET e Aavkey switches between AVI AV2 Av3 amp Aava OOOO S o Power PowersMontoronando 10 11 ports located on bottom of monitor Rev 10 27 15 Page 6 of 12 Author CNR Dakota Micro Ine B Remote Operations XII MENU SETTINGS 66 e666 60 OW ee POWER ON OFF Mute Enable Disable sound Flip image Left Right Flip image Up Down Navigation Arrows MENU Enters the menu Also acts as enter button in menu settings MODE Adjusts screen display modes RESET Reset your selection TIMER
13. s 92 field of view 3 6mm e Optional lenses available include 6mm 12mm amp 16mm A complete lens guide is available on our website e Function plugs on Elite AgCam versions allow for IR ON OFF and switching of forward reverse image e Removable replaceable camera tail Rev 10 27 15 Page 2 of 12 Author CNR Dakota Mire Inc DMAC 7M 9M C1 C2 User Manual B Monitors Feature the latest in LCD technology 4 Camera Inputs Available in 7 or 9 size Include event triggers for each camera input Color brightness contrast and volume controls that allow compensation for use in different environments Remote control sun shield and metal U bracket monitor stand included C Cables Silicone jacket enables high flexibility in all temperatures e Our durable power video extension cables come in 20 and 60 standard lengths and feature sturdy watertight connectors e Additional power video cables available in the following lengths 10 30 40 50 amp 80 II PARTS OF AN AGCAM A Camera 1 Camera Body IR Function Plug MIR Function Plug Retaining Screw x3 Camera Tail Input Camera Bracket Fiber Washer x2 Magnet Pe m m eS SCP Magnet Nut Function Plugs Elite Models Only There are two 2 function plugs on the bottom of each Elite AgCam camera near the camera tail They will look like two 2 additional screws at a slight angle recessed into the camera body The fun
14. tach the power input connector 3 above to your included 12v cigarette lighter power adaptor 2 Plug cigarette lighter adaptor into 12v power source SS eR eS SS B Hardwire Power Adaptor 1 If you would like to hardwire your power supply please contact your local AgCam dealer for available hardwire power adaptors PN DWAC HARDWIRE 2 Dakota Micro hardwire power adaptors have a maximum circuit capability of 7 5 amp C Fuses 1 There is a small in line glass fuse located on the red and black power wire 3 above When replacing this fuse use a MAX 2amp glass fuse 2 There is a small glass fuse located on the inside tip of the 12v portion of the power adaptor PN DMAC 12v When replacing this fuse use a MAX 4amp glass fuse Rev 10 27 15 Page 5 of 12 Author CNR Dakota Mire Inc DMAC 7M 9M C1 C2 User Manual X EVENT TRIGGER WIRE OPERATIONS A Event Trigger Wire Color Guide 1 Camera 1 Green 2 Camera 2 Purple 3 Camera 3 Gray 4 Camera 4 White B Event Trigger Wires Explained Event trigger wires can be attached to any 12v positive event This will cause the monitor to change to that camera regardless of the state of the monitor i e ON OFF or channel selection The most recent event will be the primary display So if two 2 video channels AV1 amp AV2 are attached to an event output the event that happens last will change the monitor to its respective camera view The wires can be attached to any
15. ted warranty for all Products applies to all other geographic locations unless otherwise stated in writing by Dakota Micro This limited warranty does not apply to any issues connected with appearance that have no relation to the performance of the Product nor to any Product the exterior of which has been damaged or defaced which has been subjected to improper voltage or other misuse abnormal service or handling or which has been altered or modified in design or construction In order to enforce the rights under this limited warranty the purchaser should follow the steps set forth in the complete Dakota Micro Warranty amp Repair Policy listed on page 11 section XVI and provide proof of purchase to Dakota Micro Neither the sales personnel of Dakota Micro nor any dealer or any other person is authorized to make any warranties other than those described herein or to extend the duration of any warranties beyond the time periods described herein The warranties described herein shall be the sole and exclusive warranties and remedies provided by Dakota Micro Correction of defects in the manner and for the period of time described herein shall constitute complete fulfillment of all liabilities and responsibilities of Dakota Micro to the purchaser with respect to the Product and shall constitute full satisfaction of all claims In no event shall Dakota Micro be liable or in any way responsible for any damages or defects in the Product which w
16. tor U bracket with 4 Wing Bolts Monitor Sun Shield 12v Cigarette Lighter Power Adaptor PN DMAC 12v styles vary by kit Il STANDARD FEATURES A Cameras INCLUDED CAMERA KIT COMPONENETS PER PN DMAC C1 Description Picture AgCam Camera Camera Bracket with Attached Magnetic Base PN DMAC CBM Camera component bag Allen wrench x2 nylon washers x2 retaining screws amp camera pigtail PN DMAC CT 60 Power Video Extension Cable PN DMAC EC60 20 Power Video Extension Cable PN DMAC EC20 Thank you for purchasing the AgCam The AgCam is a durable reliable surveillance system with the innovative ability to be quickly moved from one application to the next Training videos are available on the Dakota Micro website at www dakotamicro com e Waterproof shockproof and suitable for nearly any use e Minimum focal distance of 5 e Built in high quality CCD camera with high performance infrared IR illuminator modules e IR has effective range of 45 in complete darkness e Built in CDS light source sensor automatically turns the IR s on off by detecting the light intensity of the environment e Our exclusive Photogray camera body lens darkens in bright conditions and becomes completely transparent under low light conditions This lens is also transparent of infrared light allowing the LED s to penetrate even when it is darkened e Standard lens feature
17. y illegal or nefarious usage XV PRODUCT WARRANTY REPAIR PROCESS 1 For Technical Support call 1 866 462 4226 OR email techsupport dakotamicro com 2 Technician will assist in troubleshooting product malfunction 3 If product malfunction cannot be remedied and a repair is deemed necessary Technician will issue a Repair Authorization RA number IMPORTANT NOTE The Technician will note on the RA form if the repair APPEARS to be a warranty or non warranty issue based on customer description of the issues at hand No final determination can be made until inspection and testing of the equipment is completed at the factory 4 To ensure fast and effective repairs customer is required to send e Dakota Micro Product that Technician has requested deemed necessary in the proper diagnosis and repair of malfunction This may include some or all components of the kit e Original Copy of purchase receipt e For serialized items ONLY If a copy of the original purchase receipt cannot be provided then DAKOTA MICRO will use the product manufacture date e Customer information including return street addresses NO PO Boxes amp phone number If the phone number is not included the customer will be sent a letter requesting the needed information e RA Number provided by Dakota Micro Technical Support e Shipping and associated costs to ship product to DM factory to be borne by the customer unless otherwise specified 5 Customer should mail product to Da
Download Pdf Manuals
Related Search