Wireless Puck Switch User Manual
Contents
1. Wireless Puck Switch User Manual Overview This is a Non Proxy driver that implements no Control4 Proxy We need to add inSona_NonDimmable_Light driver and then make connections between them With the use of the additional light driver puck switch supports all of the Light V2 proxy commands and events Product Features 1 Seamlessly dock Control4 Home Controllers such as HC200 HC300 HC250 HC800 etc 2 Work as a Zigbee router so that other device can join the mesh via the puck switch 3 Provide two contact inputs two indicator LED outputs as well as two line voltage outputs 4 Work with 12V keypad and achieve light control in Control4 system 5 OTA support to update firmware through Zigbee 6 Support all of Control4 Light V2 commands and events 7 Standard or high Radio power level is selectable by modifying driver property Installation Guide 1 Installation position of Equipment must meet the following requirements Within the range of Zigbee communicating network Avoid 2 4G communication channel conflict with Wi Fi Bluetooth Keep away from metal objects Important Strictly follow the requirements above so that the product can work efficiently L N Puck Switch Terminal 42 4p Lamp 1 Lamp 2 Biye Netural LOAD 1 External Switch 12V Common LOAD 2 LED 2 LED 1 Button Switch 2 Button Switch 1 Wire Configuration Figure Wiring Configuration according to the silkscreen on th2. areful when you change it 5 Events When Button xx Attach property is set to Attach Nothing puck switch can be used as a keypad device we have the same button events as Control4 device inSona Wireless Puck 2 Events Qo matte 1 1 Button 1 Double Tap Button 1 Triple Tap Button 1 Hold Button 1 Released Button 2 Single Tap Button Double Tap Button 2 Triple Tap Button Hold Button 2 Released Light 1 Level Change Light 2 Level Change Operation and Display 1 Identify Press the ID button Identify Button 4 times for identifying the Green LED starts to blink When the device successfully joined the network Green LED will be turned off 2 Leave Mesh Press the ID button 9 times to leave Zigbee mesh When the device goes offline the Red LED turns on Note button beside the inSona logo on the puck switch and the first auxiliary switch work as ID Button This table describes the ID Button functions and LED status When the relay has Red LED and Green LED joined the network and binks once powered on again the Power On successively and red green LED will turn ona LED turns on while and turn off indicating rejoin process If Green LED doesn t Green LED starts l Identify 4 a blink you shall press the blinking then goes off banoni utton 4 times again 1 If Red LED remains off then the operation has failed Please press l the button 9 times Leave Zigbee Mesh Red LED
3. ault status of light when device reboots Button 1 Attach Button 2 Attach Set to AUTO ATTACH to achieve keypad function otherwise Light control Debug Mode Control the output log of driver Radio Power Level Set the Zigbee Radio Power level to enhance link quality Firmware Update Display the current firmware version and OTA update information Properties mentioned above are the main setting options which user must know 3 Connections inSona Wireless Puck 2 Hame Type Connection Input Output Connected To Control Outputs amp Light 1 Control PANEL HOHDIM LOIGHT Output inSona Non Dimmable Light Li ght EA Light 2 Control PANEL HOHDIM_ LIGHT Output inSona Non Dimmable Light Li ght Make connections between the two drivers now user can control puck switch through Control4 Light V2 Proxy 4 Actions Update Firmware button used to update the firmware If Firmware Update in the Properties tab reads xxxx is available users shall press this button to update firmware Force Update Firmware button used to force a firmware update included in this driver User can also use this button to force downgrade the firmware to an older one Set Radio Power Button used to modify the current Zigbee radio power level of this device Get Radio Power Button used to show the current Zigbee radio power level of this device in the lua tab when Debug Mode is true Notice Standard power level is used in most cases be c
4. e shell L Line Wire N 2 Neutral Wire L1 L2 Load outputs D1 D2 Indicator LED outputs K1 K2 Contact inputs C Common terminal must be connected to 12V terminal on external switch NC Not connected Steps to installation 1 Short the 12V terminal and common terminal on the auxiliary switch 2 Connect C on the puck switch with Common terminal 3 Match the K1 K with switch outputs on auxiliary switches 4 Match the D1 D with indicator LED inputs on auxiliary switches Driver Setup and Configuration 1 Add Driver Device type is others Manufacture is inSona double click to add puck switch driver Mf Local Online P Certified Only Results sort by Relevance insona Wireless Puck 2 iona IH CO1 WF 2 others Device type is Light V2 Manufacture is inSona double click to add additional light driver 7 Local Online PP Certified Only TOCE Results Sort by Relevance insona_ Nonlimmable Light inona inona Honlimmable Light Light 2 Default Status OFF Button 1 Attach ATTACH NOTHING Button Attach ATTACH NOTHING uento OO ee Hardware Version _ Not Avaliable Not Avaliable Driver Version 20 Refresh Time i q Light 1 Status Light 2 Status Show current status of light Light 1 Default Status Light 2 Default Status Set the def
5. t working Check the Power Supply of the device Check the Zigbee network status of the device through Composer Make sure the Connections between drivers are connected according to the instructions Make sure the light works normally 2 If you find the green LED is always on after the device is powered on please press the button 9 times to leave the former Zigbee mesh Then press 4 times to join the network
6. turns on l again 2 Uers can t control the device until rejoining the Zigbee Mesh OTA Update Device support OTA Over The Air that means you can update firmware through Zigbee The Firmware Update in Properties Tab will indicate the latest firmware version when new updates are available Firmware Update If you want to update the firmware switch to Action tab Properties Actions Lua Update Firmware Force Update Firmware Read Firmware Yersion Click Update Firmware button to start updating The Firmware Update in Properties Tab will display the update progress The new firmware will be downloaded in proximately 10 minutes File verification will be performed after downloading IMPORTANT The device will restart automatically and load the new firmware after verfication Do not cut off the power during the process as it may lead to non repairable damage Usually the loading process will finish in 1 minutes Finare Upite Loading new firmware Da not cut the power supply After the loading process Firmware Update will display Firmware is updated showing the operating firmware has been updated to the version of the driver Fwar Update invented O If the update fails or you need to redo update or downgrade use the Force Update Firmware button in Action Tab The process is the same to Firmware Update Troubleshooting 1 if the Wireless Puck Switch is no
Download Pdf Manuals
Related Search