User Manual - Perth Technology
Contents
1. 55 1 INTRODUCTION 1 1 PREODUCT INTRODUCE The serial of DVR include 4 channels 8 channels and 16 channels that is CIF D1 resolution digital video recording DVR which have local recording playback support triple code remote network surveillance data backup parameter setting motion detection I O alarm setting PTZ and USB mouse USB2 0 backup IE browser and back up etc 1 2 PRODUCT FEATURE H 264 compression Two USB interface USB2 0 for data backup USB2 0 for mouse operation support 1 pcs 3 5 SATA HDD at most Special file system for security 16 bit color translucent user friendly GUI with notes for selected menu items Optimized one four channel simultaneously playback double level user management Support the live view parameter setting and copy playback video via network gt gt 1 2 1 SPECIFICATION Module Picture H 264 compression 1 0Vp p 75Q BNCx4 1 0Vp p 75Q BNCx8 1 0Vp p 75Q BNCx16 Video out 1 0Vp p 75Q BNCx1 VGAxI 1 0Vp p 75O0 BNOx1 SPOTX1 VGAx1 Resolution Live D1 Live DI Live D1 Record 2CH D1 2CH Record 8CH CIF Record ICH DI 15CH CIF CIF frame rate PAL 100 Fps CIF PAL 200 Fps CIF PAL 400 Fps CIF NTSC 120 Fps CIF NTSC 240 Fps CIF NTSC 480 Fps CIF Video mode Manual recording Scheduled recording Movement alarm video and External alarm recording communication RS485x1 USB2 0x2 RS485x1 RS232x12. T m 53 5 Fix the HDD from the bottom Make sure screws had gotten through the cotton pads as below picture Notice Newly installed HDD should format before recording 54 5 FAQ If your problem is not listed below please call our toll free number for more support Question DVR is not working after starting Answer lt Check the adaptor input lt gt Check the on off power line is it well connected lt Check the power on off lt Check the upgrade procedure lt Check the main board of DVR Question DVR is rebooting automatically or stopped after starting the DVR for several minutes Answer Instability or low input voltage Bad track hard drive or the line of hard drive is bad On off power supply is not enough The front end video signal instability High temperature too much dust too bad the DVR operating environment The main board is not well connected with other boards The hardware of DVR is defective Question No output of single channel multi channel or all channel video gt lt Please check the adaptor of camera whether to see if it is well connected lt Please check the cable for connecting video input output in the back panel of DVR lt Please insert the video source directly into the display device and check If they are causing the problem lt Check the brightness of the picture and bring it back to its original default setting lt
3. 48 the recording file which belong to which channel SIZE is display the size of this file Unit MB is display the type of recording file there are two types normal and alarm press BACKUP button can export the selected files to USB storage 2 After moving the cursor up and down and select the files and press APPLY to enter into playback interface If the all channels have recording files it will be playback all windows at the same time 3 If setup as Open in the RECORD TIME in DISPLAY it will show the date time when playback record file If setup as Close it will not display time 4 When playback can press to play slowly press and 4 to speed reverse play also can press m to pause and frame by frame play Press Exit to exit from playback and return to the former menu 5 When finished playback files it will return to the file list interface 15 2 2 2 6 BACKUP You can use USB for backup should insert USB device into the USB2 0 port before backup files And it is support USB OTG You can select the recording file by direction keys and press Enter means selected OK There is a 4 at the end of the selected recording files and press Enter again the Vv will disappear that means cancel the select we can start export the recording files after selecting and press BACKUP to start to backup as follow Progress Count 5 files backu
4. to enter into setup interface you can check the parameter settings as in GUI of DVR os TEM SETTING LANGUAGE ENGLISH TY MODE PAL GMT 08 DAYLIGHT SAVING TIME DST DST MODE LIETOM 2 00 2 00 SETUP SETTING Click medi iden and ELUDES to enter into setup interface you can check the parameter settings as in GUI of DVR DATE TIME SYNC 14 59 47 Click as in GUI of DVR to enter into system information interface you can check the parameter settings 42 oro OPERATE EXECLITE REBOOT RESTORE FACTORY PARA UPGRADE AUTO MAINTENANCE ENABLE On i REFRESH 3 4 3 7 SYSTEM INFO Click SAEI to enter into system information interface see below picture this interface shows HDD status remain record time firmware version and all the information 1s fixed VERSION INFO DEVICE SN 1044 DEVICE TYPE DMSe208 APP VERSION 7110805 J Click Bal MAIN to enter into setup interface you can check the parameter settings as in GUI of DVR 43 ODE SETTING VIDEO PARA AY CHANNEL BIND COLOR ADJUST ORD SETTING HARD DISK INFO LIST ALARM SETTING Ai NUMBER DISK STATE TOTAL SIZE DISK FREE SIZE NORMAL 1000204M 11542M NO DISK NO DISK NO DISK NO DISK NO DISK NO DISK NO DISK 1 2 3 4 5 8 REFRESH 3 4 3 8 USER SETTING Click to enter into system information int
5. Click 4 GUI of DVR REC PARA FRAME RATE 25 QUALITY COPY SETTINGS to enter into setup interface you can check the parameter settings as AV CHANNEL BIND AUDIO 181540 CHANNEL BIND TO CHANNEL DEFAULT BINDING CH NAME Kuu to enter into setup interface you can check the parameter settings as in 37 COLOR ADJUST CHANNEL 08 08 2011 14 55 29 CHZ CONT m 20 SAT 29 HUE 32 COPY SETTINGS TO DEFALILT when you See SETTINGS which you would like to copy COPY SETTINGS button you can copy the setting to the channel ALL CHi piss ceH6 CHANE Emm S RECORD SETTING REC CTRL PARA REC ENABLE AUDIO ENABLE UNIT OF PACK MINUTE TIME OSD i SEES TIMER REC SCHEDULE REC TYPE ALARM NORMAL NO ofa le s je s le tu ju pio LJ ET COPY SETTINGS TO REFRESH 38 3 4 3 3 ALARM Click ALARM SETTING and Ses ESRB enter into setup interface you can check the parameter settings as in GUI of DVR EVENT TYPE ENABLE OM Click S to enter into setup interface you can check the parameter settings as in GUI of DVR CHANNEL CHANNEL1 EVENT TYPE ENABLE MOTION SENSITIVITY OUTPUT ALARM OUT TIME v BUZZER TIME POST REC PRE REC TIME REFRESH 3 4 3 4 PTZ Click to ent
6. APPLY to make the setting for submenu valid It will no use when exit directly This DVR have a special feature is when you move the mouse to everywhere there will have the explanation information showed auto 2 2 2 1 DISPLAY Move the cursor to DISPLAY Icon with the orange box means that selected press Enter to enter i rt o the setting interface Chn Name 2 CH3 OSITION U L U U L setup c Open 2 Open LIVE TIME open RECORD TIME CH01 CH04 you can select the CH01 CH04 CH05 CH08 CH09 CH12 16CH DVR CH13 CH16 16CH DVR here CHN NAME press Enter to enter into the setting interface POSITION press Enter to switch name location there are 5 options COLOR press Enter to enter into setting interface as following 10 Color Setup HUE BRIGHT CONTRAST SATURATION Apply Exit Press Enter or key or directly drag the cursor to set colors including chroma brightness contrast and saturation press APPLY to save the parameters LIVE Open Means the channel is allowed to view the live mode Close means not LIVE TIME display time while in live view Open Means yes Close means not RECORD TIME display time while recording Open Means yes Close means not 2 2 2 0 RECORD SETUP Move the cursor to RECORD Icon with the orange box means that selected press Enter to erter into the setting interface Press Confirm and enter into the setup int
7. Remote control batteries run out lt Remote control is damaged or the front panel of DVR is damaged Question WEB cannot login Answer lt Please check the network to see if it is connected Check if LINK or 100M LED is displayed normally on the panel use ping xxx xxx xxx xxx DVR IP to check if the Internet is linked properly lt Recommended to use Windows or Vista operating system also use IE6 0 browser or IE7 0 browser lt ActiveX control has been blocked Please manually install ActiveX control again lt Please install DX8 1 and upgrade your video card driver Question There is no picture or picture is not clear when you preview the recording or playback the recording via IE Answer gt Ifyou access DVR by IE please choose Wan in web environment lt Please try Close windows by the right mouse button and try Open windows again Question It displays other members are setting while setting DVR by IE Answer lt It probably means someone else is setting the DVR Please check DVR configuration interface or exit DVR 56
8. General Security Privacy Content Connections Programe Advanced Select a Web content zone to specify its security settings Local intranet Trusted sites Restricted sites MM Internet 4 This zone contains all Web sites you haven t placed in other zones Security level for this zone Custom Custom settings To change the settings click Custom Level use the recommended settings click Default Level Custom Level Default Level Figure 3 1 3 click on the Custom Level enter the security settings Figure 8 2 28 Security Settings Settings Actives controls and plug ins E Automatic prompting For Actives controls Disable Enable Binary and script behaviors Administrator approved Disable lw Download signed Actives controls Disable Enable e Prompt m Download unsigned Actives controls PO mre Lie 5 gt KG RORSA4CA ROR RROR A GRORGAORORR RORORCROROA A ROEOROR RIaA L c a OE 4c R R 3 Rana a w Reset custom settings Brea a Figure 3 2 ActiveX controls and plug ins installed v ActiveX controls automatically prompt v tothe marked safe for scripting of ActiveX controls to execute script v not marke
9. No video input signal or too weak lt Display settings in the preview set to be closed lt The hardware of DVR is defective Question DVR cannot record after startup and the interface 1s showing H Answer lt Make sure power adaptor is DC 12V lt sure HDD is formatted lt Check the power and data connection cables of the HDD lt HDD is defective lt SATA port is not working Question What is meaning of R M H showed in interface Answer gt R means the channel is recording lt means the channel is on motion detection means the channel is on alarm lt means there is either no HDD the HDD is bad or the HDD is full Question DVR is having problem with real time images such as bad image color or serious brightness distortion Answer gt IfPAL and NTSC is not correctly selected on the BNC output the images will be in black and white gt DVR is not compatible with monitor lt video transmission distance is too far lt The setting of DVR color brightness and so on are wrong Question No audio sound when monitoring Answer lt sound box or speaker functions Also check possible short circuit lt Audio source may be connected to the video channel You can click to full screen to check lt The hardware of DVR is defective 55 10 11 Question No audio sound when playing back Answer lt Setting problem open audio video item lt Check the audi
10. each point Enter Save the changed and the preset point Cruise PTZ This function allows to start cruise of PTZ camera Caccouding the presetting point to auto cruise 2 2 3 4 MOBILE Move the cursor to MOBLE Icon with the orange box means that selected press Enter to enter into setting interface 21 USER NAME The login user name of DVR PASSWORD The login Password of DVR PORT the port for mobile view you should open the port in the router for mobile view Please note that the server port of DVR must with the same port of mobile MOBLESS LAN Select different mobile network from the options of WIFI 2 5G 2 7G 3G and WIFI and press Enter to switch different network 2 2 3 5 MOTION DETECT Move the cursor to MOTION Icon with the orange box means that selected press Enter to enter into setting interface EE Ic A Sensitivity Mid Area Default CH01 CH04 you can select the CH01 CH04 CH05 CH08 CH09 CH12 16CH DVR CH13 CH16 16CH DVR here STATUS Each channel has corresponding channel switch press Enter to turn on or turn off the motion detection for each channel SENSITIVITY Each channel has corresponding sensitivity setting including four standards highest high middle and low press Enter key to switch MD AREA each channel has corresponding regional motion detecting setting move the cursor to corresponding setting press Enter to enter regional setting interface red a
11. the port of IE browser via HTTP PPPOE username and password fill the username and password of the internet service offer and apply it and reboot the system After rebooting the device will save it and set the PPPOE as default network type If succeed the IP address will be automatically config as dynamic IP of WAN 13 DDNS Setup DDNS server Hostname Username Password Default Apply Exit DDNS There are Open Close and if there is a DDNS service please setup it as Open SERVICE There are 3 services to select 3322 dyndns and perfecteyes HOST NAME Input the name of the host server USERNAME Input in the name of the user PASSWORD Input the password for DDNS 22 24 SEARCH Move the cursor to SEARCH Icon with the orange box means that selected press Enter to enter into the setting interface DATE You can adjust the checking date and time press Enter input the number directly to adjust the year month date After finishing the time setting move the cursor to SEARCH and press APPLY can see the recording status of this date As follow Record Search Chm All 2 Bate 2010 10 15 Record State OCT 01 02 1050607 06809 1 171619 20 21 22 23 24 25 26 21 28 29 30 31 02 03 04 05 Oe eae 18 13 20 21 start to search the Record file Detail files Log Exit Instruction 1 MONTH It will show all the recording status in this month Green means normal recording Red means alarm recording Groundin
12. 4 1 4 PLAY Move cursor to the icons it will highlighted when selected 88 Open all windows Capture picture save in local disk the default save path is C DVR Quickly start all channels recording video here the left up corner of each channel have nine normal recording video symbol R click icon to switch between single screen quad 16 split full screen olume adjust button 3 4 1 5 OTHER OPERATION 1 Select one channel at preview screen the selected channel s frame will be change to RED double click left key enter to the selected channel single screen display 2 Click one Chanel via left key at preview screen then click right key will occur window shortcut Menu see below picture CONNECT Ed CONNECT ALL Ed DISCONMECT ALL Es You can open shut down and start this channel s record via shortcut menu 3 Click right key at one live view screen click open all windows or close all windows will quickly open close all windows 342 REPALY IE Browser Step 1 Click Replay option Step 2 Click the date which you would like to playback k REFRESH Step 3 Also you can clic gt button to search the video file again or use file list to SEAR choose which channel you would like to playback and then click on The video file list will be displayed 34 REMOTE SETTING LOCAL SETTING LOGOUT 2011 F1 FILE LIST 000000 Step 4 Click specified video f
13. AU HT L ON IP 6 212 Use Remote controller to select device tntr nnne 6 LLA 79 05 O ERATION 4 EE EE EV ee ee RE _ ___ __ nee ett eens ee 8 2 2 OPER TION rr 9 NEELI N 9 T E A 9 S Fey AO gt 76 2 23 gt PE 28 3 1 REMOTE SETTING eea 28 ILAA NETWORK SECURITY SETTING S mealies 28 Ila CGONNECTION 29 I2 APORT c 31 3 3 NN 32 3 4 OPTRA TION TINT PIE Di T MTM 32 32 bn MED III mTo M 34 bo M PINTO TG TG 36 DET MESA TIENE 45 E 45 DYRIN TOWN ____________ __ 46 4 1 PRODUCT OV ERY MEW 46 41 1 The Definition of Buttons and Connectors on Front Panel eese nnns 46 212 definition of buttons and connectors on fear panel esses esee nnne nennen nnns 48 ddad CONEIS CL Lg _ 49 EET BITTE rece 49 ALD NAWO DIGI wives EE 37 4 2 HDDINSTALLATION _____ 6 52
14. H 264 NETWORK Embedded DVR USER MANUAL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RICK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE gt gt CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT ONTENT TAUNTS OTC HON ____________ 4 1 1 FREODUC TINTRODUCE errre _________ ___ _ _6 4 1 2 ial D VEU 4 DES EL 4 007 70 07 4 PP D EE D YOU 264 4 L ARAMES E m J 1 3 ENVIRONMENT 5 ZT CEO RA ION a E 6 2 1 REMOTE KEY INSTRUCTION wissecaxssastssendassndsnnedansabinticesnndsencosdoxesiubonnaheniehiadd guwmhainebebeeereyedascbeteaoeduededs 6 VPE
15. ION Icon with the orange box means that selected press Enter to enter into setting interface at this interface mainly display system hardware features and firmware version include Device ID Software Ver and MAC Address System Infomation Device ID DMS8316 Software Ver T101013 MAC Addr 00 Dp0 92 B2 C0 3E 2 2 4 6 SYSTEM MAINTAIN Move the cursor to MAINTAIN Icon with the orange box means that selected and press Enter to enter into system maintain setup interface Maintain Auto Maintain cClose v Be Se LR Power Off Default Apply AUTO MAINTAIN When switch is on you can setup the time for device to restart SYSTEM UPDATE Copy the update file to the dvrupgrade folder in the root directory of the thumb driver and insert it into USB 2 0 then press Enter to upgrade the firmware and it will display the process of the system upgrading as following 26 W ari L I C Upgrading don t remove USB Do not power off period system updating eee REBOOT means restart the device POWER OFF The button allows to shut down the system from OSD Now you can power off safely 27 3 IE OPERATION 3 1 REMOTE SETTINGS 3 1 1 NETWORK SECURITY SETTINGS Please set internet security level before install ActiveX 1 Open IE Browser select Tools Internet options 2 In the dialog box that appears select the Security tab Figure 8 1 Internet Options
16. ORMAT Press ENTER to switch between the date patterns there are YY MM DD and MM DD YY two options TIME Setup system time via numeric key TIME FORMAT Press ENTER to switch between the date patterns there are 12 HOURS and 24 HOURS two options Remark You must press APPLY to save it otherwise it won t save the modify if you exit this interface DST DST settings you can setup DST as you want here 2 2 4 2 PASSWORD Move the cursor to PASSWORD Icon with the orange box means that selected press Enter to enter into the setting interface Device ID 700000 User ID Enable User Name admin Password adie Confirm tid User Right Control PTZ Config Argum System Maintain OK Apply Exit Device ID Press figures to set Device ID directly After finished if you want to control DVR by remote controller you need to press Login Lock Device ID first then you can control it by remote controller Please check Chapter Three for the introduction of remote controller User ID Press OK to select user ID it supports 5 User IDs User Name You can change user name here Note admin can not be changed Password Enter figures to set your passwords Note max 6 figures System Administrator admin default password is 123456 default password of user is 123456 User Right Control PTZ Have right to control PTZ 24 Config Argum Have right to change system parameters settings System M
17. UCT OVERVIEW 4 1 1 The Definition of Buttons and Connectors on Front Panel 07 apreance adapt with 4 channels device and 8 channels device POWER REC STOP H 264 DVR n POWER esoo H 264 DVR gt m i Buttons on Front Panel T NN Function keys Playback play by frame Slowly playback PTZ Controler Status indicator dons we 0b 46 four buttons Confirm operation Enter 20 apreance adapt with 4 channels device and 8 channels device oo60 SOG aoe Buttons on Front Panel me m EZ CI HN w Playback play by frame On means network has connected Status indicator Alarm Hard drive full of light RO Recording Recording control buttons Playback play Multi screen switching Function keys MENU Main menu PTZ O O o 47 direction key include up down F left 4 right four buttons Mouse or storage device connected 1 operation POWER Shutdown system 4 1 2 definition of buttons and connectors on fear panel 07 20aprean adapt with 4 channels device and 8 channels device OFF 0000606006660666 9 10 1 5 6 2 Physical connector Connector description 48 BEEN Audio Input For connecting audio signal Alarm Input 8 I O alarm input Alarm Output I O output for alarm RS485 RS 485 for connecting PTZ 4 13 Connector
18. aintain Have right to maintain systems Such as system upgrade system default 2 2 4 3 VIDEO AUDIO SETUP Move the cursor to A V SETUP Icon with the orange box means that selected press Enter to enter into setting interface Video Audio Setup Norm Poll Time VGA Resolution 1280x1024 Volume Margin Reboot system NORM press Enter to switch camera system has PAL and NTSC two options POLL TIME the interval for channel loop function SEQUENCE you can setup the channel sequence as you want here VGA RESOLUTION press Enter key to setup the VGA resolution there 1024 768 1280 1024 1920 1080 1440 900 four options VOLUME move cursor to VOLUME SETUP press Enter to enter into volume setup interface press number keys or directly drag the cursor to adjust volume Remark it will restart if you modify the Norm video system VGA resolution 2 2 4 4 LANGUAGE Move cursor to select LANGUAGE Icon with the orange box means that selected and press ENTER to enter into the system language setup interface Language Language RUSSIAN PORTUGUESE SPANISH TURKISH ITALIAN PERSIAN FRENCH System language have Chinese English Russian Portuguese Spanish Turkish Italian Persian French and Polish ten options you can setup the language you want in here Remark The device will restart when you setup system language success 25 2 2 4 5 SYSTEM INFO Move the cursor to INFOMAT
19. ation area when connected Notify me when this connection has limited no connectivity Figure 3 4 30 4 Double click Internet Protocol TCP IP Figure 8 5 Internet Protocol TCP IP Properties General fou can get P settings assigned automatically if your network supports this capability Othermize You need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following address address 192 p 1 69 1 E 40 Subnet mask 255 255 255 D Default gateway 182 188 0 1 5 Use the following DNS server addresses Preferred ONS server 202 96 102 8 101 1 72 41 Figure3 5 5 See PC s IP address subnet mask default gateway Figure 8 5 in the parameters depending on the specific circumstances of different users 6 DVR set up the corresponding IP address subnet mask and default gateway see section 6 5 Network Settings DVR which the subnet mask default gateway and the PC the same as IP address must be in the same network segment but you can not have been used with the same IP address or IP addresses will result in conflict The above map for example IP address should be 192 168 0 X in which X is not 40 or 1 including the other is using the IP address and can not be more than 255 the subnet mask is 255 255 255 0 gateway to 192 168 0 1 Alterna
20. d as safe for the ActiveX controls Initialize and script v Binary and script behaviors v Binary and script behaviors v Download signed ActiveX controls v ActiveX controls and plug ins The above categories will be Enable which is very important Note Install ActiveX please close firewall and antivirus software 3 1 2 CONNECTION SETTINGS DVR through the remote access network local area network connection the client computer s IP address must be with the DVR at the same network segment in the wide area network connection through the dynamic IP address or domain name to connect when the two sides need to ensure that public network can access it The following introduces the method of local area network connection settings 1 right click My Network Places in the pop up menu click on Properties open Network Connections 2 Double click open the Local Area Connection Figure 8 3 29 Local Area Connection Status F x General Support Connection Status Connected Duration 02 04 35 Speed 100 0 Mbps Sent 3 EN Packets 35 211 35 952 3 Click Properties Figure 8 4 Description Transmission Control Pratacal Intermet Protocol The default Wide area network protocol that provides cammurnicatian across diverse interconnected networks Show icon in notific
21. e button operation When using the mouse you can input certain values using the onscreen virtual keyboard You will need to use the Virtual Keyboard when entering your User ID and Password 4 Virtual Keyboard Mouse To use the Virtual Keyboard 1 Click an option or field such as the User ID and Password fields 2 Click 0 9 to key in the desired digit 3 Click 123 to switch between numerals upper and lowercase letters and other characters only for certain options 4 Click to Backspace Delete NOTE The buttons will turn from orange to white when you select the button with the mouse cursor 5 Click T to enter confirm and close the Virtual Keyboard 2 1 4 MENU TREE You can control the DVR by a lot of menu operation This tree will show you the menu structure and it will be in details in after chapter PTZ MOBILE MOTION EXIT MAIN MENU TIME DATE PASSWORD DEVICES A V SETUP LANGUAGE INFOMATION MAINTAIN 2 2 SYSTEM OPERSTION 2 2 USER LOGIN 2 2 1 1 STARTING THE SYSTEM To power the system ON OFF Connect the power cable to the DC 12V port on the rear panel At startup the system performs a basic system check and runs an initial loading sequence After a few moments the system loads a live display view ATTENTION By default passwords are disabled on the system You do not need to enter a password when accessing any system menus However for security purpose
22. elect CHO1 CH04 CH05 CH08 CH09 CH12 16CH DVR CH13 CH16 16CH DVR here PROTOCOL select the protocol of different PTZ there are two protocols to switch and the default is Pelco D BAUD RATE select the different baud rate for your PTZ there are 1200 2400 4800 9600 38400 57600 and 115200 DATA BIT there are 5 6 7 8 options to select default setting is 8 STOP BIT there are land 2 to select the default setting is 1 PARITY there are None Odd Even Mark Space to select the default setting is none CRUISE ON means open the scanning auto cruise function for corresponding channel OFF means not open ADDRESS Fill the code of respective PTZ PTa setup CHO l1 CH04 CHI CH2 Pelco D Pelco D Pelco D Pelco D d 4800 w 4600 7 360410 T B T B STOP BIT PARITY ADDRESS PTZ Control 19 Pointer To select the direction of PTZ Auto Pan The middle circle is for auto pan of PTZ pee DENEN B LLL 20 Channel select For selecting the channels of PTZ camera i 1 back to previous page or exit Go to preset point Allow you to go to a specific preset point Allow you set set of specific preset points of a PTZ Set Ponit i camera Also it can Adjust the camera in a fix point Allow you to delete the selected preset OriPoint 0 Set up pre set bit quantity curPoint 001 It the starting point cruised System default point is 01 HoldTime 003 Sets the stop time at
23. er into setup interface you can check the parameter settings as in GUI of DVR 39 CHANNE CHANNEL 1 PTZ CONTROL PROTOCOL ADDRESS BAUD RATE DATA BIT COPY SETTINGS TO REFRESH 3 4 8 5 NETWORK Click Bi GUI of DVR to enter into setup interface you can check the parameter settings as in BASIC ATTE STATIC DO 18 a8 43 29 4F _ IP ADDRESS 192 168 1 118 NETMASK 255 255 255 0 PREFERRED DNS 192 168 1 1 MEDIA PORT 8200 WEB PORT GATEWAY 192 168 1 1 PPPOE ENABLE USER NAME PASSWORD DDNS ENABLE INTERYAL SERYICE HOST NAME USER NAME PASSWORD SETUP 40 MOBILE PORT NETWORK TYPE SETUP Click to enter into setup interface you can check the parameter settings as in GUI of DVR EMAIL ENABLE SEND INTERVAI 600 SECOND coL SWITCH OFF v EMAIL SETTING ADDRESS 1 enter into UPNP settings interface as below EnableUPnP Working methods ee Mapping Host Local Data Remote Data Port Local Web Port Remote Web Port Local Mobile Port Remote Mobile Port 15961 REFRESH After open UPNP DVR IP will be automatically maped to the router Note It requires router supports this function and UPNP opened 41 3 4 3 6 ADVANCED SETTING Lh ee LEM E ui L E DVANCED SETTING L k LF M Click
24. erface Only the administrator admin users can log in to add to add up to four ordinary users and only administrators can modify the normal user name and password corresponding to the ordinary user each user name must be the corresponding password to log in and the corresponding operating authority the default administrator user name admin password is 123456 ACCESS ACCOUNT 1 ACCOUNT ENABLE __ _ OE VONE PASSWORD RETYPE PASSWORD CONTROL Cont Paras E UPGRADE t VERSION INFO i i HDD INFO FUSER SETTING REFRESH Step 1 choose new user or change user and password 44 ACCESS ACCOUNT E COUNT TT 2 user name PASSWORD RETYPE PASSWORD CONTROL v REFRESH Step 2 Enable ON Step 3 Enter new user can not use the same user Step 4 enter the password must be 6 digitals Step 5 Set corresponding limits PTZ CONTROL control scanning PARA SET can change the technical parameter in far away place Upgrade format have upgrated and format HDD limit Step 5 Chick SETUP botton save added user HilDvr cx Ej A Save Success 3 4 4 LOCAL SETTING LOCAL SET TM Click DVR to enter into setup interface you can check the parameter settings as in GUI of RECORD SAVE PATH FRAME SAVE PATH FILE SAVE PATH FILE SAVE PATH capture picture and recording video save path 3 4 5 LOGOUT Click Switch to login screen 45 4 DVR INSTALLATION 4 1 PROD
25. erface and you can use direction keys and cursor to change the options Record Setup CHO1 CHO 47 CH3 Record Open Bitrate Best Resolution CIF Framerate 5 Close schedule Schedule Setup 60 Min Record file packet time Default Apply EXIT CH01 CH04 You can select the CHO1 CH04 CH05 CH08 CH09 CH12 16CH DVR CH13 CH16 16CH DVR here RECORD Open Means the channel enable for recording BITRATE There are three options corresponding different data stream standard AUDIO Open Means enable the audio recording for all channels Close Means disable audio recording REC MODE Always Means the device will start recording when it startup Schedule Recording as the schedule you can setup the schedule as you want as follow 11 Record schedule Default Apply EXit CHANNEL You can select all channels or just one channel to setup schedule WEEKLY You can setup each as you want There are ALARM NORMAL NO REC three modes if you select this there will have a in the frame that means when you select the period of the day it will record as this mode and you can just setup one day then copy the setting to all other days Different color means different record mode Red means alarm record green means normal record grounding means no record PACK TIME There are 15min 30min 45min 60min four options that means it will pack as the mode you selected Scroll to APPLY and press ENTER to save the new settin
26. g means no recording Click any date in this frame can search the recording status of that day the searching result will be showed in the below date frame 2 DAY It will show all the recording status in this day you can playback the record file in this period via click the corresponding period PLAY Youcan press Enter input number directly to setup playback time After setting move the cursor to PLAYBACK and then press APLLY to enter into video playback of that time Also you can select any period of time in the video status frame after searching press APLLY to enter into the video playback of this period 14 DETAIL FILES Enter into the video file list interface of the selected date LOG SEARCH Enter into the log searching interface 2 22 19 DETAIL FILES Setup the searching date after pressing SEARCH move the cursor to Detail files and press APPLY to enter into the video file list of this date Chn Time 00 03 44 00 031 1 Alarm 00 03 44 00 03 55 1M Alarm s 00503544 00 03 1M Alarm 00 03 44 00 03 5 1 1 Alarm 00 39 57 00 40 08 0 8M Normal 00 39 57 00 40 08 0 8M Normal List by record mode Then you can select four channels as you want to playback because 8CH DVR support 8channels playback at the same time By the way 16CH DVR support 16 channels playback at the same time 1 n CH _ m Choose 1 Instruction 1 DETAIL FILES
27. gs 22 2 NETWORK SETUP Move the cursor to NETWORK Icon with the orange box means that selected and press Enter to enter into setting interface TYPE There are PPPOE DHCP amp Static three options o STATIC Select Static in the type and press Enter to enter into the interface as followings Setup Static Port 09000 Web Port 00080 IP Addr 192 168 001 100 Netmask 2 5 5 2 5 z a Gateway 192 168 001 001 DNS Server 202 096 PORT For video transmission via IE WEB PORT setup the port of IE browser via HTTP IP ADDRESS setup the IP address and press Enter or number keys to change the value 12 NETMASK press Enter or number keys to change the value GATEWAY press Enter or number keys to change the value o DHCP Select the DHCP and enter into the interface as followings Network Setur Type DHCP Fort 09000 Web Port 80080 IP Addr 192 168 001 100 DNS Server 202 096 134 133 DDNS Setup PORT the communicate port between PC and DVR recommend use default port WEB PORT setup the port of IE browser via HTTP Remark when you setup the net mode as DHCP the router will arrange a dynamic IP for DVR o PPPOE Select the PPPOE and enter the interface as followings Network Setup PPPOE 09000 00080 Username Password DNS Server 202 096 134 133 DDNS Setup MEDIA PORT the communicate port between PC and DVR recommend use default port WEB PORT setup
28. ile which you would like to playback remotely The video will be displayed When the video file 1s playing the system won t allow you to download video files REMOTE SETTING LOCAL SETTING 20115F1H REFRESH FILE LIST ALL CHANN 9 ALL TYPE T TIME CH 17 28 35 18 28 32 17 28 35 18 28 33 E 17 28 35 18 28 33 17 28 35 18 28 34 17 28 35 18 28 34 17 28 35 18 28 33 Bo Ba 18 28 33 18 42 36 E 18 28 33 18 42 36 0 18 28 33 18 42 36 18 28 33 18 42 35 18 28 34 18 42 36 18 28 34 18 42 36 18 28 34 18 42 36 18 28 34 18 42 35 n w N o an a mm 7 O00000 Step 5 Close the playing video and then click to download video file Step 6 When the video file was downloaded the dialogue box will display 35 Information Step 7 Playback control The above purple progress bar shows download progress green progress bar shows playback progress Switch between pause play Pause Stop play Fast play Slow play Pause at next frame 343 REMOTE SETTING Click TR to enter into setup interface this interface include Encode setting Record setting Alarm setting PTZ setting Network setting Advanced setting and system information seven menus 3 4 3 1 ENCODE SETTING Click Se 33 8 11 15 to enter into setup interface you can check the parameter settings as in GUI of DVR 36 Click in GUI of DVR
29. in screen 3 Number Channel buttons While in menus press buttons 0 9 to enter values during live viewing press to view channels in full screen 4 EH Press to switch between quad and split screen displays 5 MENU Opens the main menu 6 PTZ Press to open the PTZ control window 7 EXIT Close menu windows 8 Navigation OK Move cursor in menus up Channel Up Move cursor in menus right Channel Up during playback increase forward playback speed 2X 4X 8X 16X 32X 4 Move cursor in menus left Channel down during playback increase reverse playback speed 2X 4X 8X 16X 32X Y Move cursor in menus down Channel down OK In menus press to confirm selections 9 In menus press to adjust values 10 RECORD Press to start manual recording 11 STOP Press to stop manual recording TIP When using the remote control to 12 EXTR A For the future use enter password and camera titles 13 Playback controls select the field using the navigation 44 Increase reverse playback speed 2X 4X 8X 16X 32X buttons press ENTER and then press the number buttons Press to start playback kk Press to increase forward playback speed 2X 4X 8X 16X 32X e M Press to slow playback speed by 1 2 1 4 1 8 1 16 1 32 e Press to freeze playback to one frame then press again to advance frame by frame 14 AUDIO MUTE Turn on off audio 2 1 2 Use Remote controller to se
30. interface USB2 0x 3 Data storage Support 1 SATA HDD 300GB 2TB Support 2 SATA HDD 300GB 2TB DVR 07 20 DVR 07 20 DVR 15 1 22 BASIC WORKING PARAMETER Voltage input DC 12V Input I O S5V 30v High voltage alarm RS232 BEEN Serial port for extend use 16channels RS485 BEEN Connect to PTZ Pelco D Pelco P One SATA HDD with mainstream capability 16 CH support 1 3 ENVIRONMENT ADAPTABILITY For safety while using the DVR and to prolong device life please pay attention to the following details When installing device please comply with all the electric product safety criteria Power and ground Do not touch the power and DVR with a wet hand Do not drop liquid on DVR Do not put any object on DVR Please use soft dry cloth to clean DVR do not use chemical impregnant The Device will have voltage before startup if the power line is connected to power Source Please unplug power line from power source if the Device is not intended to be used for a prolonged time 9 9999 2 DEVICE OPERATION In device operation the enter key on remote control has the same function as left click of the mouse 2 1 REMOTE KEY INSTRUCTION 2 1 1 REMOTE CONTROL The remote control is the secondary input device For navigating the system s interface To use the remote control 1 STANDBY Press to turn on off standby mode 2 LOGIN LOCK If Security has been enabled in the Setup menu press to open the user password log
31. it will delete HDD earliest recording file and it will stop deleting when the space is 10G DISABLE means when HDD space less than 500M it will stop recording and an prompt will display in live view please shutdown and replace HDD HDD FORMAT Move cursor there to select device and press APLLY to start formatting U DISK FORMAT format the external thumble drive 2 2 3 2 ALARM SETUP Move the cursor to ALARM Icon with the orange box means that selected press Enter to enter into setting interface 17 CHO1 CHO4 I O Alarm HDD Loss Video Buzzer Pre Rec CH01 CH04 you can select the CH01 CH04 CH05 CH08 CH09 CH12 16CH DVR CH13 CH16 16CH DVR here I O ALARM Each channel has an I O status that is when an alarm triggered it will activate the corresponding channel to start alarm recording N O indicate I O input level from high to low effective N C indicate I O input level from low to high effective HDD LOSS Open means it will trigger a alarm if there is no HDD and it will display an H On the bottom left of channel 1 in the live view HDD SPACE Open If the space less than 500M there is a remark in live view No enough space please change HDD after shutdown VIDEO LOSS Open when one channel has no video input it will display video loss in live view ALARM CONTRL There are alarm output buzzer Durationand pre Rec four items OUTPUT when an alarm triggered the alarm output time will be 0 sec
32. lect the device number Press LOGIN LOCK key and enter device number then you can control the device by this remote control Device number is available in PASSWORD For example Select the device with number 000001 Press LOGIN LOCK 1 then the remote controller can control this device Remark 1 Remote controller can control the device with number 000000 as default 2 If press LOGIN LOCK 0 then the remote controller can control device with any number 3 The number of device should be smaller than 000255 2 1 3 MOUSE OPERATION The mouse is the primary input device for navigating system menus NOTE Unless otherwise noted all system functions described in this manual are achieved through mouse input To use a mouse with the system 1 Connect a USB mouse to the USB MOUSE port on rear panel of the system NOTE Only the top USB port on the rear panel is designed for data backup to a USB flash drive Do not connect a USB flash drive to the bottom USB port on the rear panel Figure 1 0 Connect a USB mouse to the bottom USB port on therear panel 2 Use the mouse buttons to perform the following Left Button Click to select a menu option during live viewing in split screen double click on a channel to view the selected channel in full screen double click the channel again to return to split screen view Right Button Click to open the Sub Menu 3 Scroll Wheel No function Figure 1 1 Mous
33. o to see if it is closed in playback interface Question System time is not correct Answer lt Wrong setting or user did not click Edit to confirm lt gt Battery is not connected properly lt Battery 15 dead Please change Question Why the Stop recording by the right mouse button does not work how to stop recording Answer lt The Stop recording by the right mouse button is only suitable for Manual recording It can t stop recording when it s in start recording or the video in video plan lt If you want to stop recording please set the time is not recording Question Stop recording function by the right mouse button does not work How to stop recording Answer The Stop recording by the right mouse button is for Manual Recording only It can not stop recording when it 1s in start recording or the video is in video plan If you want to stop recording please set the time to not recoding 12 13 14 15 16 17 Question Motion detection is not working Answer lt The setting of motion detection area is not correct lt Sensitivity is too low Question CD writer USB backup error Answer lt The data exceeds the capacity of backup device lt The backup device is incompatible lt The backup device is damaged Question Remote control cannot work Answer lt The address of remote control is not correct lt The distance of remote control is too far or the angle is too biased lt gt
34. ond 10 seconds 20 seconds 40 seconds and 60 seconds BUZZER buzzer calling time setup when alarm triggered close 10 seconds 20 seconds 40 seconds and 60 seconds DURATION post recording time setup 30 seconds 1 minute 2 minutes and 5 minutes PRE REC Close Open Email setup 18 Email Enable Open Disable Close SSL Enable Open Disable Close SSL is a security link transport protocol You can encrypt your communication info including your email using SSL to prevent hackers from monitoring your email or communication info and even your password Please confirm with your email service provider if your email server support SSL or not SMTP Port The Specified sender port of SMTP server forwarding server Host Generally the SMTP port value is 25 but for SMTP port of G mail server is 465 if your E mail needs to be verified by SSL the port is going to be 465 default value and port 25 default value is the Email without SSL verification Simple Mail Transfer Protocol SMTP is an Internet standard for electronic mail e mail transmission across Internet Protocol IP networks The original sender forwarding server Host Password of original sender The target receiver of alarm notification target 2 2 3 3 PTZ SETUP Move the cursor to PTZ Icon with the orange box means that selected press Enter to enter into setting interface you can setup the parameters for each channel separately CH01 CH04 you can s
35. ping 3 file Backuping don t remove USB Instruction 1 When the space in backup device less than recording file the system will prompt Space no enough 2 You can move USB device directly when backup finished 2 2 27 LOG SEARCH Move the cursor to LOG SEARCH and press APPLY to enter into the log file list of DVR as follow window Type Content IOPERT SETUP 10 11 ALARM MD ALARM 10 10 15 ALARM 10 10 15 1 10 10 15 SETUP 10 10 15 INFO means the alarm type TRIGGER means the alarm triggered time VIDEO means whether the log has corresponding video file 2 2 3DEVICES SETUP Move the cursor to DEVICES Icon with the orange box means that selected press Enter to erter into setting interface Motion HDD Information Format Advanced Features include HDD ALARM PTZ MOBILE and MOTION DETECT 2 2 3 1 HDD MANAGE Move the cursor to HDD Icon with the orange box means that selected press Enter to enter i rt o the setting interface and you can use direction keys and cursor to change the options otal Avail Avail Time Select 1000G 993G 701Hour 0 0 Hour 0 0 Hour OHour HDD STATUS There status is ok means the HDD is ok If HDD can not run normally including unformat and no HDD there isa H display on video live view DVR can support 1HDD at most so you can select the HDD you want to format here OVERWRITE ENABLE means when HDD space less than 4G
36. rd is 123456 PASSWORD Administrator has all authorities operator has limited authorities who they can only watch playback please change the unit No and default password is blank NETWORK LAN INTERNET WAN Remark If you connect the device in WAN the IP should be a public IP 3 4 OPERATION INTERFACE There are Live view Playback and Setup options in the main interface please press them to access it 3 4 1 LIVE Click to enter into the interface as followings 32 gt Application Manager Findows internet Explorer 4 x 7 http 192 168 1 1187 w dir Application Manager REMOTE SETTING LOCAL SETTING 0870872011 17 37 55 GR GH42011 17 37 55 aHn GH 7011 17 37 55 PLAY CONTROL 0870872011 17 37 54 a lt gt v 0870872011 17 37 54 di m 200 FOCUS IRIS PANATILT POS enn CALL CLEAR 3 4 1 1 PTZ CONTROL Change the focus preset aperture to control the PTZ Click to up down left right control movement of the PTZ When hold on the one direction key the PTZ will keep circling as that direction after user press the stop key in the center of the wheel 3 4 1 2 ZOOM Click to zoom in and out Click to focus Click h to change the size of aperture 3 4 1 3 PTZ PRESET PAN amp TILT POS SS Setup preset point SET CALL CLEAR You can control it via the below three buttons 33 3
37. rea means it have activated motion detection transparent block means it have not activated motion detection 22 Move the direction key on remote control to make cursor move in the small pane green frame means the cursor has moved to this pane press Enter to select or cancel motion detection of this small pane when setup finished press exit to back to MD setup interface it will save automatically Remark IR Operation press Menu key to select or cancel the entire screen Mouse operation click left and drag the frame to setup the region for motion detection 2 2 3 6 EXIT Move the cursor to EXIT Icon with the orange box means that selected press Enter to back t o main menu 2 2 4 SYSTEM SETUP Move cursor to select SYSTEM Icon with the orange box means that selected and press ENTER to enter into the system language setup interface Password INFO Language Infomation Maintain Time and Date settings System setups include time date password video audio language info and maintain six options 2 2 4 4 DATE TIME SETUP Move cursor to select TIMEDATE Icon with the orange box means that selected and press ENTER to enter into the date time setup interface 23 Time Date 10 15 2010 Date Format MM DD YY Tine 08 58 33 Time Format 24Hours Time Zone GMT 08 00 DST Setting Open 057 Mode StartTime 2 00 AM lst Default Apply DATE Setup system date via numeric key DATE F
38. s it is highly recommended to enable passwords on the system using the Password Menu NOTE 1 Ifthere is no HDD in device or the device didn t read the HDD or the HDD didn t be formatted it will display H in the video preview interface 2 You must format the HDD in the DVR before first using The steps as follows MainMenu gt Device gt HDD management gt format After formatting the system will restart 2 2 1 2 SYSTEM LOGIN Login the main menu Right click anywhere on the screen it will pop up a menu list then select main menu If use remote controller or front panel just press MENU button Login admin Password Username Click the User Name drop down box select your user name If you want to register another user to login please select admin to login and choose Main Menu System Password to open the another user Password Enter the correct password Note The default system password is enabled every time you boot into the system requires you to enter the password for the user name to enter the system System Administrator admin default password is 123456 or default password of user1 is 123456 2 2 2 GUI OPERATION The main menu nclude DISPLAY RECORD NETWORK SEARCH DEVICES and SYSTEM ff PL um Mie LI Menu T TL Anns Record Search EI Lar L JL F Remark You must after pressing
39. s for Alarm Peel off the color skin of the cable and then insert the cable into the slot on the rear panel DVR The connection part for alarm NC may be considered COM Alarm int Alarm 2 Alarm in3 Alarm in4 Alarm ins Alarm in6 Alarm in Alarm inf COM 1 NO1 CHD COM NO R54B5A R54B5B 12v output 49 414 Alarm Input and Output There are 8 sets alarm input connector and set output for this DVR Alarm input 1s for connection IR annunciator fog sensor The connection diagram of DC alarm input as following 4 POWER The connection diagram of alarm output as following POWER 50 4 1 5 System Network Diagram i d gt Video in Video in Video in Video Aude o In ig 19000 a mg BN yee 32 Alarm in Switch E Audio out Audio in iterat RS485 PTZ Controi PC PC Notebook PC Mobile surveillance s rre Power 51 4 2 HDD INSTALLATION Please installation the HDD as the following steps 1 Open the machine there are 4 screw holes used to fix the HDD as below ee jm Se aetna 2 Take out the fixed screws and cotton pads used to protect HDD As below picture 3 Tear the cotton pads and post in the screw holes as shown 52 4 Put the circuit side of HDD on the board and make the screw holes correspond to the cotton pads l F f
40. te ONS server 202 3 2 FEATURE Through the IE browser of OS and install the software you are able to do the network operation remotely which is much more convenient DVR support C S B S and visit in LAN and WAN also support IP and domain name visiting Remark Operating system Windows XP Windows Vista and Browser IE6 0 IE7 0 is recommended 31 3 3 USER LOGIN Input the DVR local IP in IE browser when changed the port you should add the port number after IP address e g if DVR local IP is 192 168 1 118 LAN and the port is 8088 you should input I http 192 168 1 118 8088 The default port is 8088 and directly input http 192 168 1 118 to access the login interface as following File Edit View Favorites Tools Help E Web Application Manager Microsoft Internet Explorer DER Ed QJ a Search 5 Favorites 62 Address 46 http 192 168 1 118 m 6 uus SIMPLIFIED CHINESE TRADITIONAL CHINESE USER LOGIN USER ID admin PASSWORD eeeeee NETWORK LAN LOGIN Internet Select English interface in the top left side Input username and password to enter into the system The username and passport is same as the ones set in DVR Sign in IE must enter a user name and password to log in the user name and password consistent with the DVR the default administrator user admin the corresponding passwo
Download Pdf Manuals
Related Search