Home
Episode® Rack Mount UPS Network Management Card
Contents
1. The Refresh button is used to 1 Turn off the UPS before search the entire local network for SNMP cards removing the expansion port cover on the UPS I Power Device Network Utility 2 Remove the two retaining screws of the expansion port cover then remove the cover Power Devices MAC Address IP Address Subnet Mask Gateway DHCP Name E8 00 0C 15 01 01 02 192 168 10 144 255 255 255 0 192 168 10 1 Enable RMCARD202 3 Install the EP 400 NMC Network Management Card into the expansion port 4 Re install and tighten the retaining screws Figure 1 5 Connect the Ethernet cable to the LAN port of the Episode Network Management Card 4 Select the SNMP card you are setting up Click on the Tools menu and select Device Setup or double click the SNMP card you want to configure 6 Turn on the UPS 5 You can modify the IP Device Network Settings Address Subnet Mask and Gateway address for the Device MAC Address listed in the Device Network Settings window as shown in Figure 2 Device MAC Address 00 0C 15 0A 04 0A Using DHCP yYes No IP Address 168 10 133 Subnet Mask 255 255 0 6 Modify the IP subnet mask Gateway 168 10 1 or gateway address Enter the new addresses into the corresponding fields Figure 2 7 You will need to enter a Authentication User Name and Password Enter the user nam
2. LINK Indicator Ethernet connector RX TX Indicator Link RX TX Definitions for LED Indicators The Network Management Card is not Off connected to the Network or the Network Management Card power is OFF QUICK INSTALLATION GUIDE On Yellow The Network Management Card is Episode UPS Network connected to the Network Management Card TXIRX LED color E P 400 N MC Off The Network Management Card power is OFF On Green The Network Management Card power is ON Intelligent Network Management Card allows a UPS system to be managed monitored and configured Receiving transmitting data packet Figen Reset finished Step 2 Configure the IP address for the Episode Network Management Card Method 1 Using the SNMP Card Configuration Tool The User s Manual iS located 1 Install the SNMP Card Configuration Tool from the included CD It is i located on the CD in the tools network folder Double click the Power on the provided installation disk Device Network Utility installation file Setup msi to begin the installation 2 After installation is complete run the Power Device Network Utility program Under All Programs select Power Device Network Utility INSTALLATION GUIDE 3 The main dialog of the SNMP Card Configuration Tool program is Step 1 Hardware Installation shown in Figure 1 The configuration tool will display all network cards present on the network
3. e and password to save changes for the SNMP card e in the authentication User name window as shown in Password Figure 3 Default user name admin Default password admin Figure 3 Authentication window Network Settings Information 8 If IP address is successful you will Setup MAC 00 0C 15 0A 0A DA OK see a message that the IP Power Device Network Information i j Disable set up is OK as shown in TP Adames Brie 01 j t 255 255 255 Figure 4 orien 192 168 101 Note The denotes a modified field Figure 4 Setup IP Address successful message Method 2 Using a command prompt 1 Obtain the MAC address from the label on the Network Management Card rear panel Each Management card has a unique MAC address 2 Use the ARP command to set the IP address Example To assign the IP Address 192 168 20 240 for the Network Management Card which has a MAC address of 00 0C 15 00 00 01 you will type in the following command prompt from a PC connected to the same network as the Network Management Card 1 Type in arp s 192 168 20 240 O00 0C 15 00 00 01 then press Enter 3 Use the Ping command to assign a size of 123 bytes to the IP 1 Type in ping 192 168 20 240 I 123 then press Enter 2 If the replies are received your computer can communicate with the IP address WEB INTERFACE Login Account There are two user account types Administrator default username admin defaul
4. t password admin Viewer default username guest default password guest The administrator can access full functions including enable disable the viewer account The viewer can access the read function but can not control or change any settings Trouble Shooting Problem Solution O O Unable to configure 1 Check the LED status the normal condition the Management is both yellow and green LED is on Card by method1 or If green LED is off method2 gt Check if the Management Card is properly seated in the UPS and the UPS power is on If yellow LED is off gt Check if the network connection is valid 2 Check if the operated PC is on the same physical network as Management Card is Unable to ping the Use method1 and method2 to get correct IP Management Card address of the Management Card If the operated PC is on a different physical network from the Management Card verify the setting of subnet mask and the IP address of gateway Lost the username Please refer to the Reset to Default Setting and password Recover from a Lost Password in the user s manual For Technical Support 1 866 838 5052 110207
Download Pdf Manuals
Related Search
Related Contents
取扱説明書をダウンロード HACCP入門のための手引書 4 - Festo plaquette Osram 162204 fluorescent lamp This Page is Intentionally Blank TIP501 - powerbridge.de Copyright © All rights reserved.
Failed to retrieve file