Operation Guide 3198
Contents
1. e See Daylight Saving Time DST for details about DST setting 5 Press to exit the setting screen e The day of the week is displayed automatically in accordance with the date year month and day settings Daylight Saving Time DST Daylight Saving Time summer time advances the time setting by one hour from Standard Time Remember that not all countries or even local areas use Daylight Saving Time To toggle the Timekeeping Mode time between DST and Standard Time 1 Use to display the current Home City Time T 1 DST indicator screen 2 Hold down until the seconds start to flash which indicates the setting screen 3 Press to display the DST setting screen 4 Press to toggle between Daylight Saving Time gf displayed and Standard Time g ff displayed 5 Press to exit the setting screen e The DST indicator appears on the Timekeeping screen to indicate that Daylight Saving Time is turned on 12 24 Hour Format e With the 12 hour format the PM indicator appears to the left of the hour digits for times in the range of noon to 11 59 p m and no indicator appears to the left of the hour digits for times in the range of midnight to 11 59 a m e With the 24 hour format times are displayed in the range of 0 00 to 23 59 without any indicator e The 12 hour 24 hour timekeeping format you select in the Timekeeping Mode is applied in all other modes Changing the City Setting of2. gt Hour gt Minutes One time Alarm Daily Alarm Selection lt 4 While a setting is flashing use and to change it as described below Screen To do this Do this wea Change the hour Use and etH and minutes e With the 12 hour format set the time correctly as a m or p m PM indicator anjan Toggle between Press a One time Alarm One time Alarm on 41 gf and Daily Alarm Daily Alarm on 41 5 Press to exit the setting screen Alarm Operation The alarm tone sounds at the preset time for 10 seconds regardless of the mode the watch is in e Alarm and Hourly Time Signal operations are performed in accordance with the Timekeeping Mode time e To stop the alarm tone after it starts to sound press any button To test the alarm In the Alarm Mode hold down to sound the alarm To turn an alarm on and off 1 In the Alarm Mode use to select an alarm 2 Press to cycle through the alarm settings as shown below Alarm One Time Alarm Daily Alarm On On e In all modes the alarm on indicator is shown for the alarm that is currently turned on e The alarm on indicator flashes while the alarm is sounding To turn the Hourly Time Signal on and off 1 In the Alarm Mode use to select the Hourly Time Hourly time signal Signal on indicator 2 Press to toggle it
3. Home City code and the T 1 indicator for about one second e You can change the current time setting for your Home City Time T 1 only e For Local Times T 2 T 3 T 4 you only can change the city code and DST setting Changing the Current Home City Time and Date Settings 1 Use to display the current Home City Time T 1 screen 2 Hold down until the seconds start to flash which indicates the setting screen 3 Press to move the flashing in the sequence shown below to select other settings Seconds gt DST gt City Code Minutes kG Illumination Duration Setting 12 24 Hour l Day lt Month a Format lt lt Alarm Mode Countdown Timer Stopwatch Mode 4 When the setting you want to change is flashing use and to change it as described below Screen To do this Do this Sa Reset the seconds to 4 Press DST Toggle between Daylight Saving Press re Time gf and Standard Time 9 F TY Change the city code 0 58 Change the hour or minutes Use east and west Use and 2H Toggle between 12 hour 24 and Press d 24 hour 2 44 timekeeping eo ig Change the year ii Change the month or day Use and Use and Toggle the setting between Press LT 1 5 seconds 4 and 3 seconds 7
4. a Local Time You can select any one of the city codes in the table at the back of this manual as a Local Time city 1 Display the Local Time whose city setting you want to change and then hold down for about two seconds until the current city code starts fo flash 2 Use east and west to select the city code you want 3 Press to display the DST setting screen 4 Press to toggle between Daylight Saving Time 84 displayed and Standard Time g ff displayed 5 After the settings are the way you want press Changing Your Home City Time Use the following procedure to change your current Home City Time to any one of the three Local Times 1 In the Timekeeping Mode press to display the Local Time which you want to make your Home City Time 2 Press and at the same time e This makes the Local Time you selected in step 1 your new Home City Time CASIO Operation Guide 3198 Illumination An LED light emitting diode illuminate the display for easy reading in the dark Illumination Precautions The illumination provided by the light may be hard to see when viewed under direct sunlight e Illumination automatically turns off whenever an alarm sounds e Frequent use of illumination runs down the battery To turn on illumination In any mode except when a setting screen is on the display press 8 to turn on illumination e You can use the procedure above to select either 1 5 seconds o
5. on and off e The Hourly Time Signal on indicator is shown on the display in all modes while this function is turned on Countdown Timer The countdown timer can be set within a range of one Seconds second to 24 hours An alarm sounds when the countdown reaches zero e All of the operations in this section are performed in the Countdown Timer Mode which you enter by pressing Hours Minutes 1 10 second To configure the countdown timer 1 While the countdown start time is on the display in the Countdown Timer Mode hold down until the current countdown start time starts to flash which indicates the setting screen 2 Press to move the flashing in the sequence shown below to select other settings m gt Hours gt Minutes Seconds lt 3 When the setting you want to change is flashing use and to change the flashing item e To specify a countdown start time of 24 hours set 8 08 a9 4 Press to exit the setting screen To use the countdown timer Press while in the Countdown Timer Mode to start the countdown timer e When the end of the countdown is reached the alarm sounds for ten seconds or until you stop it by pressing any button The countdown time is reset to its starting value automatically when the alarm sounds e Press while a countdown operation is in progress to pause it Press again to resume the countdown e To stop a countdown
6. operation completely first pause it by pressing and then press This returns the countdown time to its starting value CASIO Operation Guide 3198 Stopwatch The stopwatch lets you measure elapsed time split times Seconds and two finishes e A display range of the stopwatch is 23 hours 59 minutes 59 99 seconds e A stopwatch continues to run restarting from zero after it reaches its limit until you stop it e A stopwatch measurement operation continues even if you exit the Stopwatch Mode Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement e All of the operations in this section are performed in the Stopwatch Mode which you enter by pressing Hours Minutes 1 100 second To measure times with the stopwatch Elapsed Time x a Start Stop Re start Stop Split Time Start Split SPL displayed 0 Split release Stop Two Finishes J m Start Split Stop Split release First runner finishes Second runner Display time of Display time of first finishes second runner runner Reference This section contains more detailed and technical information about watch operation It also contains important precautions and notes about the various features and functions of this watch Map and Digital Dial Hour hand Second hand Minute hand YAZA Map _ E oN Digital dial 5i
7. MA0910 EA Operation Guide 3198 About This Manual e Button operations are indicated using the letters shown in the illustration e Each section of this manual provides you with the information you need to perform operations in each mode Further details and technical information can be found in the Reference section General Guide e Press to change from mode to mode e In any mode except when a setting screen is on the display press to illuminate the display Timekeeping Mode World Time Mode Timekeeping Fes ee The Timekeeping Mode s Multi Time feature gives you PM indicator Digital dial quick and easy access to the current time and date in four Seconds different cities numbered from T 1 Time 1 through T 4 Time 4 T 1 is your Home City Time and T 2 T 3 and T 4 are Local Times Local Times are kept in synchronization with your Home City Time T 1 e The digital dial at the top of the screen indicates the current Home City Time T 1 For details on reading the map and digital dial see Map and Digital Dial Day of week Month Day Hour Minutes Switching Between Time Screens Each press of cycles the time screens in the sequence shown below 0 FR 0 FR S gt E gt 15088 LONT PRF THO e While the Home City Time T 1 screen is displayed pressing will switch the day of the week month day indication to the currently selected
8. en Standard Time and Daylight Saving Time while UTC is selected as the city code To change your Home Time city to the current World Time city 1 In the World Time Mode use to display the city you want to make your new Home Time city 2 Press and at the same time e This makes the World Time city you selected in step 1 your new Home Time city Alarms Your watch has a total of five alarms each of which you can configure as a daily alarm or one time alarm e Daily Alarm Sounds at the preset time each day e One time Alarm Sounds once at the preset time and then is disabled automatically You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour e All of the operations in this section are performed in the Alarm Mode which you enter by pressing e Alarms operate in coordination with the current Home City Time Alarm on indicator Alarm number Alarm time Hour Minutes To set an alarm time 1 In the Alarm Mode use to scroll through the alarm screens until the alarm number you want to set is displayed gt gt f gt J 3j 2 After you select an alarm hold down until the hour setting of the alarm time starts to flash which indicates the setting screen This operation turns on the One time Alarm automatically 3 Press to move the flashing in the sequence shown below to select other settings
9. peration tone on off Auto Display function Battery One lithium battery Type CR2025 Approximately 10 years on type CR2025 10 seconds of alarm operation 1 5 seconds of illumination per day City Code Table Code City GMT Differential Cate city PPG Pago Pago 11 ATH Athens HNL Honolulu 10 CAI Cairo 2 ANC Anchorage 9 JRS Jerusalem YVR Vancouver 8 MOW Moscow LAX Los Angeles JED Jeddah YEA Edmonton 7 THR Tehran DEN Denver T DXB Dubai 4 MEX Mexico City 6 KBL Kabul 4 5 CHI Chicago KHI Karachi 5 NYC New York 5 DEL Delhi 5 5 SCL Santiago 4 KTM Kathmandu YHZ Halifax DAC Dhaka 6 YYT St Johns RGN Yangon RIO Rio De Janeiro 3 BKK Bangkok 7 FEN Fernando de Noronha 2 SIN Singapore RAI Praia 1 HKG Hong Kong UTC BJS Beijing LIS Lisbon 0 TPE Taiepei LON London SEL Seoul MAD Madrid TYO Tokyo PAR Paris ADL Adelaide 9 5 ROM Rome GUM Guam 10 BER Berlin SYD Sydney STO Stockholm NOU Noumea 11 WLG Wellington 12 UTC offset GMT Differential 3 8 9 e Based on data as of December 2008 e The rules governing global times UTC offset and GMT differential and summer time are determined by each individual country
10. r 3 seconds as the illumination duration When you press the illumination will remain on for about 1 5 seconds or 3 seconds depending on the current illumination duration setting World Time World Time shows the current time in 48 cities 31 time City code zones around the world e All of the operations in this section are performed in the A oa World Time Mode which you enter by pressing im nae fe ODE I To view the time for another city code In the World Time Mode press to scroll eastwardly through city codes e For full information about city codes see the City Code Table WT e If the current time for a city is wrong check your Timekeeping Mode time and time zone settings and make the necessary changes Current time and date in the zone of the selected city code To toggle a city code time between Standard Time and Daylight Saving Time 1 In the World Time Mode use east to display the DST indicator city code time zone whose Standard Time Daylight Saving Time setting you want to change 2 Hold down for about one second to toggle Daylight Saving Time DST displayed and Standard Time DST not displayed e The DST indicator is on the display whenever you display a city code for which Daylight Saving Time is turned on e Note that the DST Standard Time setting affects only the currently displayed city code Other city codes are not affected e Note that you cannot switch betwe
11. rolling The and buttons are used in various modes and setting screens to scroll through data on the display In most cases holding down these buttons during a scroll operation scrolls at high speed Initial Screens When you enter the World Time or Alarm Mode the data you were viewing when you last exited the mode appears first Timekeeping Resetting the seconds to GG while the current count is in the range of 30 to 59 causes the minutes to be increased by 1 In the range of 00 to 29 the seconds are reset to GG without changing the minutes e The year can be set in the range of 2000 to 2099 e The watch s built in full automatic calendar makes allowances for different month lengths and leap years Once you set the date there should be no reason to change it except after you have the watch s battery replaced CASIO World Time e The seconds count of the World Time is synchronized with the seconds count of the Timekeeping Mode e All World Time Mode times are calculated from the current Home City Time in the Timekeeping Mode using UTC time offset values e The UTC offset is a value that indicates the time difference between a reference point in Greenwich England and the time zone where a city is located e The letters UTC is the abbreviation for Coordinated Universal Time which is the world wide scientific standard of timekeeping It is based upon carefully maintained atomic cesium clocks that keep time accura
12. tely to within microseconds Leap seconds are added or subtracted as necessary to keep UTC in sync with the Earth s rotation Auto Display Auto Display continually changes the contents of the digital display To turn off Auto Display Press any button to turn off Auto Display This returns to the Timekeeping Mode To turn on Auto Display In the Timekeeping Mode hold down O for about three seconds until the watch beeps Note e Auto Display cannot be performed while a setting screen is on the display Specifications Accuracy at normal temperature 30 seconds a month Timekeeping Hour minutes seconds p m PM month day day of the week Time format 12 hour and 24 hour Calendar system Full Auto calendar pre programmed from the year 2000 to 2099 Other Multi Time one Home City Time and three Local Times Daylight Saving Time summer time Standard Time World Time 48 cities 31 time zones and Coordinated Universal Time Other Standard Time Daylight Saving Time summer time Home Time City World Time City swapping Alarms 5 alarms One time or Daily Hourly Time Signal Countdown Timer Measuring unit 1 10 second Input range 1 second to 24 hours 1 second increments 1 minute increments and 1 hour increments Stopwatch Measuring unit 1 100 second Measuring capacity 23 59 59 99 Measuring modes Elapsed time split time two finishes Illumination LED light emitting diode Selectable illumination duration Other Button o
13. th HEZA e Map In the Timekeeping and World Time modes the map shows the zone where the currently displayed digital time is from In the Alarm Timer and Stopwatch modes it shows the zone of the currently selected Home City Time T 1 e Digital dial In all modes segments indicate the current Home City Time T 1 hour minute and second Button Operation Tone The button operation tone sounds any time you press one of the watch s buttons You can turn the button operation tone on or off as desired e Even if you turn off the button operation tone the alarms the Hourly Time Signal and the countdown alarm all operate normally Mute indicator To turn the button operation tone on and off In any mode except when a setting screen is on the display hold down to toggle the button operation tone on the MUTE indicator not displayed and off the MUTE indicator displayed e Holding down to turn the button operation tone on or off also causes the watch s current mode to change e The MUTE indicator is displayed in all modes when the button operation tone is turned off Auto Return Features If you leave the watch in the Alarm Mode for two or three minutes without performing any operation it automatically changes to the Timekeeping Mode e If you leave a screen with flashing digits on the display for two or three minutes without performing any operation the watch automatically exits the setting screen Sc
Download Pdf Manuals
Related Search