SF-80 SF-300 - Silver Pines Sound & Light
Contents
1. e Do not open the equipment and do not modify the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors e Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable e Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically e If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again e If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service e Only use fuses of same type and rating e Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PART2. Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty Equinox SF 01 CX Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment e Do not open the equipment and do not modify the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors e Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug N
3. EQUIN ee 4 www prolight co uk SF 80 Sf 300 Order code STROO8 Order code STROO9 User manual Equinox SF 80 300 Safety WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty Equinox SF 80 300 Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment
4. S e WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Equinox SF 80 300 Operations Manual control mode To control the SF 80 or SF 300 strobe in manual control mode simply plug the unit into an appropriate mains power supply Then use the flash speed control knob on the rear of the unit to set the desired flash speed The unit will now strobe to the set flash speed Remote control mode To control the SF 80 or SF 300 strobe in remote control mode first plug CF 01 CX remote controller into an appropriate mains power supply Then plug one end of the 1 4 mono jack cable signal into the IN PUT Jack socket on the rear of the unit Now plug the opposite end of the 1 4 mono jack cable signal into the OUTPUT socket on the remote controller Please be sure to set all of the manual control knobs to the off position and refer to the strobe controller user manual for operation If you wish to connect a second strobe first plug the 1 4 mono jack signal cable into the OUTPUT socket on the first master unit Now plu
5. ever pull out the plug by pulling the power cable e Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically e If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again e If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service e Only use fuses of same type and rating e Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS e WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to pe
6. g the opposite end of the 1 4 mono jack signal cable to the INPUT socket on the second slave unit To link further units together in a daisy chain fashion repeat the above step and so on Note For the best results only use the SF 01 CX remote controller Always abide by the controller user manual specifications regarding the maximum number of strobes that can be linked to one controller Daisy chain linking Controller i Equinox SF 80 300 Specifications SF 80 Specifications Lamp ST 80 Flash Rate 1 18fps Signal Connector 6 35mm mono jack Control mode SF 01 CX remote Fuse T1A 250V Power Consumption SOW Power Supply 240V 238 x 140 x 220mm Weight 1 4Kgs SF 300 Specifications Lamp ST 300 Flash Rate 1 18fps Signal Connector 6 35mm mono jack Control mode SF 01 CX remote Fuse T3 15A 250V Power Consumption 300W Power Supply 240V 278 x 140 x 220mm Weight 1 96Kgs EQUIN X www prolight co uk SfF O01 CX Order code STRO15 User manual Equinox SF 01 CX WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should
7. ople and property Equinox SF 01 CX Operations Operating instructions 1 Unpack the controller from the carton and inspect it for any damage If the unit has been damaged please contact your local dealer immediately 2 Connect the SF 01 CX controller to the strobe SF 80 or SF 300 with signal cable made of two standard 1 4 mono jacks 3 When the POWER ON OFF button is pressed down the above Red LED will light up Once the Red LED is lit this means that the controller is ready for operation 4 When the AUTO MANU button is pressed down the above Red LED will light up Once the Red LED is lit this now means that the strobe will flash according to the set interval time which can be adjusted via the speed control knob The interval time can be set from 0 1 2 seconds The TRIGGER button will also work in this mode of operation 5 When the AUTO MANU button is not pressed down you can control the flash manually via the TRIGGER button As you press the TRIGGER button the above Green LED will light up on every push in accordance to the flash Specifications Output Signal 10V DC 1 4 mono jack socket Maximum Load 4 Strobes 0 5A 250V Internal Power Consumption SW Power Supply 240V Dimensions 120 x 65 x 35 Weight 400g
Download Pdf Manuals
Related Search