User manual - Appliances Online
Contents
1. e Make electrical mains terminal free of voltage Follow connection schematic e Observe electrical safety rules e Ensure anti shock protection by installing correctly The appliance must be connected to the electrical supply by a qualified electrician e Loose and inappropriate plug and socket connections can make the terminal overheat e Have the clamping connections correctly installed by a qualified electrician e Use strain relief clamp on cable A WARNING The surface temperature exceeds 95 C To avoid a hazard underbench access must be restricted Electrical Connection Before connecting check that the nominal voltage of the appliance that is the voltage stated on the rating plate corresponds to the available supply voltage Also check the power rating of the appliance and ensure that the wire is suitably sized in accordance with local wiring rules to suit the appliance power rating The rating plate is located on the lower casing of the hob Means for disconnection must be incorporated in the fixed wiring in accordance with local wiring rules The hob is to be connected to the mains using a device that allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm eg INSTALLATION automatic line protecting cut out earth leakage trips or fuse If this appliance s mains cable is damaged it must be replaced by a special cable tyoe HOSBB F Tmax 902. C or higher The connection must be carried out as shown in the diagram The connecting links should be fitted according to the appropriate connection diagram The earth lead is connected to terminal The earth lead must be longer than leads carrying electric current The cable connections must be made in accordance with regulations and the terminal screws tightened securely Finally the connecting cable is to be secured with the mains cable cleat and the covering closed by pressing firmly lock into place Before switching on for the first time any protective foil or stickers must be removed from the glass ceramic surface A WARNING Once connected to the mains supply check that all cooking zones are ready for use by briefly switching each on in turn at the maximum setting e A duplicate rating label is supplied with this unit For easy identification of this unit after installation stick it to a readily available surface adjacent to the cooktop Sticking on the seal e Clean the worktop around the cutout area e Stick the single sided adhesive sealing tape provided on the underside of the hob around the outside edge ensuring that it is not stretched The two ends of the tape should join in the middle of one side After trimming the tape allow it to overlap by 2 3 mm press the two ends together ASSEMBLY WHC644BA 8 WHC744BA A WARNING Surface temperatures of base exceed 95 C under
3. Triple cooking zone 2300 1600 800W WHC934BA reper 9 Triple cooking zone 2300 1600 800W Single cooking zone 1200W 8 Single cooking zone 1800W Control panel PRODUCT DESCRIPTION 5 PRODUCT DESCRIPTION CONTINUED Control panel layout WHC644BA WHC744BA WHC944BA Pause On Off Lock Multi Pause Lock On Off Multi Use the sensor fields to operate the appliance The displays indicators and sounds tell which functions operate FA e SENSOR FIELD FUNCTION 1 On Off It activates and deactivates the appliance O Sets all operating zones to a keep warm setting A heat setting display It shows the heat setting Timer It selects the cooking zone O Cooking zones indicators of timer It shows for which zone you set the time O The timer display It shows the time in minutes Q It increases or decreases the heat setting It increases or decreases the time Multi It activates the outer rings on the triple zone element Lock It locks unlocks the control panel 6 PRODUCT DESCRIPTION Heat setting displays DISPLAY DESCRIPTION The cooking zone is deactivated The Keep Warm function operates The cooking zone operates The Automatic Heat up function operates There is a malfunction A cooking zone is still hot residual heat The Lock Child Safety device operates TT Tt U The Automatic Switch Off operates Residual heat i
4. off after the time set has elapsed STEP CONTROL PANEL DISPLAY E ai Touch Timer once ot light of the first cooking zone flashes wu g 2 Touch Timer once Pilot light of the second cooking zone flashes 2 0G 3 Touch Timer once Pilot light of the third cooking zone flashes DA 4 Touch Timer once Pi ot ight of the fourth cooking zone flashes Cif Cg applicable s IMPORTANT If a cooking zone is switched off the timer function set is also switched off O IMPORTANT If the pilot light is flashing more slowly the heat setting can be set or modified O IMPORTANT If other timer functions are set after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes Setting the time STEP CONTROL PANEL INDICATOR 1 Select Timer cooking zone Pilot light for the cooking zone selected flashes 2 Touch or OG to 99 minutes After a few seconds the pilot light flashes more slowly The time is set The time counts down Switching off the timer function STEP CONTROL PANEL INDICATOR 1 Select Timer cooking zone Pilot light for the cooking zone selected flashes 2 Touch The time remaining counts backwards to LI After a few seconds the pilot light flashes more slowly The time is set The time counts down OPERATING INSTRUCTIONS Changing the time STEP CONTROL PANEL INDICATOR 1 Select Timer cooking Pilot light of the selected cooking zone fla
5. or if the heat setting is not modified the relevant cooking zone switches off automatically O is displayed Before being used again the cooking zone must be set to W HEAT SETTING SWITCHES OFF AFTER 1 6 hours H 5 hours 0 4 hours 6 1 5 hours OPERATING INSTRUCTIONS 11 HELPFUL HINTS AND TIPS Cookware You can recognise good cookware from the bottoms of the pans The bottom should be as thick and flat as possible Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolourations on the glass ceramic surface which are difficult or impossible to remove NY ENVIRONMENT Energy saving Always place cookware on the cooking zone before it is switched on Switch cooking zones off before the end of the cooking time to take advantage of residual heat If possible always place lids on the pans lt tI7TI Bottom of pans and cooking zones should be the same size 12 HELPFUL HINTS AND TIPS CARE AND CLEANING A WARNING Watch out Risk of burns from residual heat A WARNING Sharp objects and abrasive cleaning materials will damage the appliance Clean with water and washing up liquid A wane Sharp cleaning agents will damage the appliance Remove residues with water and washing up liquid Cleaning the appliance after each use 1 Wipe the appliance with a damp cloth and a little washing up liquid 2 Rub the appliance dry using a clean cloth
6. Removing deposits REMOVE WHEN THE APPLIANCE USING AT ONCE HAS COOLED DOWN A scraper Sugar food containing sugar Plastics tin foil Yes Limescale and water rings Fat splashes Shiny metallic discolouration Scrapers and cleaners for glass ceramic and stainless steel can be purchased in speci 1 Place a scraper on the glass ceramic surface at an angle 2 Remove residues by sliding the blade over the surface 3 Wipe the appliance with a damp cloth and a little washing up liguid Rub the appliance dry using a clean cloth IMPORTANT Remove stubborn residues with a cleaner for glass ceramic or stainless steel Gi IMPORTANT Scratches or dark stains on the glass ceramic that cannot be re moved do not however affect the functioning of the appliance A WARNING Residues from cleaning agents will damage the appliance Remove residues with water and washing up liquid A scraper Yes Cleaner fo stainless s Yes Cleaner fo stainless s Yes Cleaner fo stainless s r glass ceramic or teel r glass ceramic or teel r glass ceramic or teel alised shops CARE AND CLEANING 13 14 TROUBLESHOOTING PROBLEM Red rings limescale or water rings shiny metallic or other discolouration scratches shadows bubbles or other miscellaneous marks or stains on ceramic glass cooktop surface correctly Cleaning maintenance of the cooktop surface is
7. TS or to find the address of your nearest state spare parts centre in New Zealand FREE CALL 0800 10 66 20 New Zealand only GOV_Warr_Aug13 WARRANTY 19 For more information on all Westinghouse appliances or for dimension and installation information call into your retailer phone or email our customer care team or visit our website AUSTRALIA phone 1300 363 640 fax 1800 350 067 email customercare electrolux com au web www westinghouse com au NEW ZEALAND phone 0800 436 245 fax 0800 225 088 email customercare electrolux co nz web www westinghouse co nz 80 Electrolux TOP TOP SERVICE Top Service encompasses the after sales service provided by The Electrolux Group to consumers including delivery home service and spare parts Westinghouse We are part of the Electrolux family Share more of our thinking at www electrolux com and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation Used under license All Rights Reserved Part Number AO2346101 Issue A ECN 36240 2014 Electrolux Home Products Pty Ltd ABN 51 004 762 341 ECN 036240 WMAN_CGH_NOV14
8. Ww Westinghouse USER MANUAL CERAMIC COOKTOPS WHC644BA WHC744BA WHC944BA WHC934BA 2 CONGRATULATIONS Dear customer Congratulations on the purchase of your new cooktop Before you use the cooktop we recommend that you read through the whole user manual which provides the description of the cooktop and its functions To avoid the risks that are always present when you use an electrical appliance it is important that the cooktop is installed correctly and that you read the safety instructions carefully to avoid misuse and hazards We recommend that you keep this instruction booklet for future reference and pass it on to any future owners After unpacking the appliance please check it is not damaged If in doubt do not use the appliance but contact your local Customer Care Centre For contact details refer to the last page of this user manual This appliance complies with requirements of Australian Standard AS NZS 60335 2 6 Conditions of use This appliance is intended to be used in household and similar applications such as e Staff kitchen areas in shops offices and other working environments e Farm houses e By clients in hotels motels and other residential type environments Bed and breakfast type environments Please ensure you read the instruction manual fully before you call for service or a full service fee could be applicable R
9. bench access must be restricted by use of non combustible barrier on installation ASSEMBLY 17 ASSEMBLY CONTINUED 2 Electrolux Warranty FOR SALES IN AUSTRALIA AND NEW ZEALAND APPLIANCE BUILT IN OVEN COOKTOP AND FREESTANDING COOKERS This document sets out the terms and conditions of the product warranties for Electrolux Appliances It is an important document Please keep it with your proof of purchase documents in a safe place for future reference should you require service for your Appliance 1 In this warranty a acceptable quality as referred to in clause 10 of this warranty has the same meaning referred to in the ACL g ACL means Schedule 2 to the Competition and Consumer Act 2010 Appliance means any Electrolux product purchased by you and accompanied by this document ASC means Electrolux authorised service centres Electrolux means Electrolux Home Products Pty Ltd of 163 O Riordan Street Mascot NSW 2020 ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux NZ Limited collectively Electrolux of 3 5 Niall Burgess Road Mount Wellington in respect of Appliances purchased in New Zealand major failure as referred to in clause 10 of this warranty has the same meaning referred to in the ACL and includes a situation when an Appliance cannot be repaired or it is uneconomic for Electrolux at its discretion to
10. cycled The plastic components are identified by marking gt PE lt gt PS lt etc Discard the packaging materials as household waste at the waste disposal facilities in your municipality 949 163 173 520 x 900 490 x 880 220 240 50 60 6500 4 800 1600 2300 1200 1800 1200 N A 949 163 176 410 x 900 360 x 825 220 240 50 60 5300 3 800 1600 2300 N A 1800 N A 1200 TECHNICAL DATA 15 16 INSTALLATION INSTRUCTIONS A WARNING This must be read The laws ordinances directives and standards in force in the country of use are to be followed safety regulations proper recycling in accordance with the regulations etc IMPORTANT Installation may only be carried out by a qualified electrician The minimum distances to other appliances and units are to be observed Anti shock protection must be provided by the installation for example drawers may only be installed with a protective floor directly underneath the appliance The cut surfaces of the worktop are to be protected against moisture using a suitable sealant The sealant seals the appliance to the work top with no gap Do not use silicon sealant between the appliance and the work top Avoid installing the appliance next to doors and under windows Otherwise hot cookware may be knocked off the rings when doors and windows are opened A WARNING Risk of injury from electrical current e The electrical mains terminal is live
11. d the relationship between you and Electrolux are governed by the law applicable where the Appliance was purchased Where the Appliance was purchased in New Zealand for commercial purposes the Consumer Guarantee Act does not apply To the extent permitted by law and subject to your non excludable statutory rights and warranties Electrolux excludes all warranties and liabilities other than as contained in this document including liability for any loss or damage whether direct or indirect arising from your purchase use or non use of the Appliance For Appliances and services provided by Electrolux in Australia the Appliances come with a guarantee by Electrolux that cannot be excluded under the ACL You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the failure does not amount to a major failure The benefits to you given by this warranty are in addition to your other rights and remedies under a law in relation to the Appliances or services to which the warranty relates At all times during the Warranty Period Electrolux shall at its discretion determine whether repair replacement or refund will apply if an Appliance has a valid warranty claim applicable to it For Appliances and services provided by Electrolux in New Zealand the A
12. ecord model and serial number here Record model and serial number here CONTENTS CONTENTS Important Ssafet YA NSUUCHO NS Eeh 5 Product AES CKIBT WA 4 Operating INSTFUCTIONS wa Aaa 8 HEINEKEN 2 Care and cleaning wwwwwwawwammmawmanmaaamamaa wama 3 Mroublesho ting sesse aa dietetics 4 Technical Gata kino 5 Environment Concer Saee 5 Installation INStrUCTIO S arenasi 6 PRS SEIT DNIE EE E AA 7 Warranty io E ees 9 Please read the user manual carefully and store in a handy place for later reference The symbols you will see in this booklet have these meanings A WARNING This symbol indicates information concerning vour personal safety A CAUTION This symbol indicates information on how to avoid damaging the appliance Gi IMPORTANT This symbol indicates tips and information about use of the appliance NY ENVIRONMENT This symbol indicates tips and information about economical and ecological use of the appliance IMPORTANT SAFETY INSTRUCTIONS A WARNING Please comply with these instructions If you do not any damage resulting is not covered by the warranty General safety e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Do not lea
13. heat settings Touch Lock for 4 seconds The symbol comes on e The child safety device is switched on Switching off the child safety device e Start the hob with On Off Do not set the heat settings Touch Lock for 4 seconds The symbol comes on e Stop the hob with On Off e The child safety device is switched off IMPORTANT The child safety device can only be switched on and off if no heat setting is set Overriding the child safety device The child safety device can be switched off in this way for a single cooking session it remains activated afterwards e Start the hob with On Off The symbol comes on Touch Lock for 4 seconds The symbol 2 comes on Until the appliance is next switched off it can used as normal After switching off the appliance the child safety device is active again O IMPORTANT After overriding the child safety device a heat setting or a function must be set within approx 10 seconds otherwise the appliance automatically switches itself off OPERATING INSTRUCTIONS 9 10 OPERATING INSTRUCTIONS CONTINUED Using the timer FUNCTION CONDITION OUTCOME AFTER THE TIME HAS ELAPSED Automatic cut out A heat setting is set Acoustic signal LU flashes Cooking zone switches off Countdown timer Cooking zones not in use Acoustic signal OD flashes O IMPORTANT If a heat setting is set on this cooking zone in addition to a countdown timer the cooking zone is switched
14. ndicator The induction cooking zones make the heat necessary for A cooking directly in the bottom of the cookware The glass WARNING ceramic is hot from the heat of the cookware Risk of burns from residual heat PRODUCT DESCRIPTION 7 OPERATING INSTRUCTIONS Switching the appliance on and off at CONTROL PANEL DISPLAY PILOT LIGHT Switch on Touch On Off for 2 seconds onna lights up Switch off Touch On Off for 2 seconds H none goes out IMPORTANT After switching on within approx 10 seconds a heat setting or a function must be set otherwise the appliance automatically switches itself off Setting the heat setting oe CONTROL PANEL INDICATOR To increase Touch to 3 To decrease OU 3 to To switch off Touch and at the same time U Function not available for WHC934BA O IMPORTANT The keep warm setting lies between 2 and U It is used to keep food warm Switching the outside ring on and off By switching the outside rings on or off the effective heating surface can be matched to the size of the cookware To switch on the middle ring Touch Multi for 1 2 seconds One power indicator is lit To switch on the outside ring Touch Multi for 1 2 seconds Two power indicators are lit To switch off the outside ring Touch Multi for 1 2 seconds The second power indicator goes out To switch off the middle ring Touch Multi for 1 2 seconds The first power indicator goes out O IMPORTANT Before an out
15. not covered under warranty If a service call is placed to clean the cooktop you will be charged for the visit Pitting of ceramic glass surface Spillovers of liquid with high sugar content More than 10 seconds have passed since the appliance was switched on The cooking zones will not switch on or are not functioning The child safety device is switched on L Several sensor fields were touched at the same time Automatic switch off has been triggered The lock is switched on U Acoustic signal sounds when The control panel is wholly or partly appliance is switched off covered by objects The residual heat indicator is not The cooking zone was only on for a displaying anything short time and is therefore not hot There is still residual heat on the cooking zone H The automatic warm up function is not switching itself on The highest heat setting is set o The heat setting was set using the sensor field Acoustic signal sounds and The On Off sensor field has been appliance switches itself on and covered up e g by a cloth then off again after 5 seconds another acoustic signal sounds Gis lit Overheating protection for the cooking zone has been triggered e Automatic switch off has been triggered and number are displayed Electronics fault POSSIBLE CAUSE REMEDY Cooktop surface has not been cleaned e Use a ceramic glass cleaner such as Cerapol e The
16. ppliances come with a guarantee by Electrolux pursuant to the provisions of the Consumer Guarantees Act the Sale of Goods Act and the Fair Trading Act To enquire about claiming under this warranty please follow these steps a carefully check the operating instructions user manual and the terms of this warranty b have the mode c have the proof of purchase e g an invoice available d telephone the numbers shown below You accept that if you make a warranty claim Electrolux and its ASC may exchange information in relation to you to enable Electrolux to meet its obligations under this warranty and serial number of the Appliance available Important Notice Before calling for service please ensure that the steps listed in clause 13 above have been followed FOR SERVICE or to find the address of your nearest state service centre in Australia PLEASE CALL 13 13 49 For the cost of a local call Australia only SERVICE AUSTRALIA A Electrolux ELECTROLUX HOME PRODUCTS www electrolux com au FOR SPARE PARTS or to find the address of your nearest state spare parts centre in Australia PLEASE CALL 13 13 50 For the cost of a local call Australia only FOR SERVICE or to find the address of your nearest authorised service centre in New Zealand FREE CALL 0800 10 66 10 New Zealand only SERVICE NEW ZEALAND 2 Electrolux ELECTROLUX NZ Limited www electrolux co nz FOR SPARE PAR
17. rea you will bear the cost of a travel of an authorised representative b transportation and delivery of the Appliance to and from Electrolux or its ASC In all instances unless the Appliance is transported by Electrolux or an Electrolux authorised representative the Appliance is transported at the owner s cost and risk while in transit to and from Electrolux or its ASC 6 Proof of purchase is required before you can make a claim under this warranty 10 11 12 14 You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship Electrolux is not liable in the following situations which are not exhaustive a the Appliance is damaged by i accident i misuse or abuse including failure to properly maintain or service ii normal wear and tear v power surges electrical storm damage or incorrect power supply incomplete or improper installation i incorrect improper or inappropriate operation ii insect or vermin infestation iii failure to comply with any additional instructions supplied with the Appliance b the Appliance is modified without authority from Electrolux in writing V VI VI VI c the Appliance s serial number or warranty seal has been removed or defaced d the Appliance was serviced or repaired by anyone other than Electrolux an authorised repairer or ASC This warranty the contract to which it relates an
18. repair an Appliance during the Warranty Period g Warranty Period means the Appliance is warranted against manufacturing defects in Australia for 24 months and in New Zealand for 24 months following the date of original purchase of the Appliance h you means the purchaser of the Appliance not having purchased the Appliance for re sale and your has a corresponding meaning 2 This warranty only applies to Appliances purchased and used in Australia or New Zealand and used in normal domestic applications and is in addition to and does not exclude restrict or modify in any way any non excludable statutory warranties in Australia or New Zealand 3 During the Warranty Period Electrolux or its ASC will at no extra charge if your Appliance is readily accessible for service without special equipment and subject to these terms and conditions repair or replace any parts which it considers to be defective Electrolux or its ASC may use remanufactured parts to repair your Appliance You agree that any replaced Appliances or parts become the property of Electrolux This warranty does not apply to light globes batteries filters or similar perishable parts 4 Parts and Appliances not supplied by Electrolux are not covered by this warranty 5 To the extent permitted by law you will bear the cost of transportation travel and delivery of the Appliance to and from Electrolux or its ASC If you reside outside of the service a
19. se types of spills must be removed immediately with a special scraper for the glass If not permanent damage to the cooktop glass can occur which is not covered under warranty e Switch the appliance on again Deactivate the child safety device See the section Child safety device Only touch one sensor field Remove any objects pan cloths etc that are lying on the control panel Switch the appliance on again e Switch off the lock See the section Locking unlocking the control panel e Remove objects If the cooking zone is supposed to be hot call the Customer Service Department Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function 1 Switch off the cooking zone 2 Set the cooking zone using the sensor field Do not place any objects on the control panel e Switch off the cooking zone Switch the cooking zone on again e Switch off the cooking zone Switch the cooking zone on again e Disconnect the appliance from the electrical supply for a few minutes Take the fuse out of the house s wiring system If after switching on again is displayed again call the customer service department If you are unable to remedy the problem by following the above suggestions please contact your dealer or the Customer Care Department A WARNING IMPORTANT Repairs to the appliance are only to be carried out by q
20. shes faster Time remaining is displayed zone 2 Touch or U Ito 99 minutes After a few seconds the pilot light flashes more slowly The time is set The time counts down Displaying the time remaining for a cooking zone CONTROL PANEL FIELD DISPLAY Select Timer cooking zone Pilot light of the cooking zone selected flashes faster The time remaining is displayed After a few seconds the pilot light flashes more slowly Switching off the acoustic signal CONTROL PANEL FIELD DISPLAY Touch Timer The acoustic signal to acknowledge The acoustic signal stops Automatic switch off Cooking surface If after switching on the cooking surface a heat setting is not set for a cooking zone within approx 10 seconds the cooking surface automatically switches itself off If one or more sensor fields are covered by objects a pan cloths etc for longer than approx 10 seconds a signal sounds and the cooking surface switches off automatically e Ifall cooking zones are switched off the cooking surface automatically switches it self off after approx 10 seconds Control panel When the appliance is switched off if one or more of the sensor fields on the control panel are covered for more that 10 seconds an acoustic signal sounds The acoustic signal switches itself off automatically when the sensor fields are no longer covered Cooking zones If one of the cooking zones is not switched off after a certain time
21. side ring can be switched on the inside ring must be switched on Locking unlocking the control panel The control panel with the exception of the On Off sensor field can be locked at any time in order to prevent the settings being changed e g by wiping over the panel with a cloth Switch on Touch Lock for 5 seconds Switch off Touch Lock the previously set heat setting O IMPORTANT When you switch the appliance off the locking function is automatically switched off OPERATING INSTRUCTIONS Using the automatic warm up function All cooking zones are eguipped with an automatic warm up function When setting a heat setting using when starting from 2 the cooking zone switches to full power for a certain amount of time and then automatically switches back to the heat setting set FP CONTROL PANEL DISPLAY PILOT LIGHT Switch on only when starting at Touch o Switch off Touch TT Not used Touch O IMPORTANT If during the automatic warm up Aa higher heat setting is selected e g from J to 5 the automatic warm up is adjusted U to A after 5 seconds to U U to u 3 to 3 to HEAT SETTING LENGTH OF THE AUTOMATIC WARM UP MIN SEC 0 30 1 100 1 40 4 50 4 6 30 10 10 6 2 00 3 30 8 4 30 3 ae The child safety device The child safety device prevents unintentional use of the appliance Switching on the child safety device e Start the hob with On Off Do not set the
22. tangled General safety e The appliance may only be installed and connected by trained registered service engineers e Built in appliances may only be used after they have been built into suitable built in units and work surfaces that meet standards n the event of faults with the appliance or damage to the glass ceramic cracks scratches or splits the appliance must be switched off and disconnected from the electrical supply to prevent the possibility of an electric shock e Repairs to the appliance must only be carried out by trained registered service engineers Safety during use Remove stickers and film from the glass ceramic e There is the risk of burns from the appliance if used carelessly e Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware e Overheated fats and oils can ignite very quickly Warning Fire hazard e Switch the cooking zones off after each use A WARNING If the surface is cracked switch off the appliance to avoid possibility of electric shock SAFETY 3 4 PRODUCT DESCRIPTION Cooking surface layout WHC644BA 8 WHC744BA WHC944BA PRODUCT DESCRIPTION o Single cooking zone 1200W Single cooking zone 1800W Single cooking zone 1200W Control panel O Triple cooking zone 2300 1600 800W Single cooking zone 1200W Single cooking zone 1200W Single cooking zone 1800W Control panel 8000
23. ualified service engineers Considerable danger to the user may result from improper repairs TROUBLESHOOTING If the appliance has been wrongly operated the visit from the customer service technician or dealer may not take place free of charge even during the warranty period TECHNICAL DATA MODEL WHC644BA WHC744BA WHC944BA WHC934BA 949 163 175 949 163 174 Product dimensions 520x1590 520 x 700 d x w mm Cut out dimensions 490 x 560 490 x 560 d x w mm Voltage volts 220 240 220 240 Cycles Hz 50 60 50 60 Total power Watts 6500 6500 Elements Watts 4 4 Front Left 800 1600 2300 800 1600 2300 Rear Left 1200 1200 Front Right 1200 1200 Rear Right 1800 1800 Centre N A N A NY ENVIRONMENT Disposal The symbol K on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Packaging material The packaging materials are friendly to the environment and can be re
24. ve the appliance unattended during operation e This appliance should be used only for normal domestic cooking and frying of food The appliance must not be used as a work surface or as a storage surface e Additions or modifications to the appliance are not permitted Do not place or store flammable liquids highly inflammable materials or fusible objects e g plastic film plastic aluminium on or near the appliance Children s safety The cooking zones will become hot when you cook Therefore always keep small children away from the appliance T he appliance is not intended for use by young hildren or infirm persons without supervision e Children should be supervised to ensure that they do not play with the appliance A WARNING Accessible parts will become hot during use To avoid burns voung children should be kept away Correct operation Always monitor the appliance during operation Do not use an external timer or a separated remote control system to operate the appliance e Only use the appliance for domestic cooking tasks Do not use the appliance as a work or a storage surface Do not put or keep very flammable liquids and materials or fusible objects made of plastic or aluminium on or near the appliance e Other than the connection point in the terminal block do not let the electrical supply cord touch the appliance or hot cookware Ensure electrical supply cord is not
Download Pdf Manuals
Related Search