DC/AC Standard Fuel Transfer Pumps User`s Manual
Contents
1. conditions with working cycles longer than 30 minutes can cause the motor temperature to rise thus damaging the motor itself Each 30 minute working cycle should always be followed by a 30 minute power off cooling phase GENERAL DESCRIPTION These products are positive displacement rotary vane pumps Depending on installation and viscosity these pumps can deliver up to 8GPM or 30LPM Their rugged design makes for a long life of dependability TECHNICAL INFORMATION gt Inlet 2 male on tank adapter 3 4 female on pump Outlet 3 4 female for 8GPM 30LPM Built in bypass valve Furnished with m 13ft 4m delivery hose H 1pc steel suction pipe m 1pc Aluminum manual nozzle E 2 Quick change coupling VV Vv gt Electrical Specification ELECTRICAL POWER CURRENT Flow Rate Voltage Maximum Amp L min GPM 1031938 30 8 PUMP MODEL OPERATING CONDITIONS Temperature min 20 C max 60 C Relative Humidity max 90 FLUID COMPATIBILITY These products are compatible with the following fluids Diesel Kerosene Mineral Spirits AN Do NOT use with other fluids without consulting manufacturer INSTALLATION INSTRUCTIONS 1 Tightly screw suction pipe into inlet coupling of pumping unit Extend suction pipe into truck tank or barrel to within 3 of tank bottom 2 Screw inlet coupling of pump into 2 tank or barrel opening Inlet coupling must be completely and securely threaded into an undamaged tank or ba2. DC AC Standard Fuel Transfer Pumps User s Manual G Sku No 1031938 WARNING Read carefully and understand all INSTRUCTIONS before operating Failure to follow the safety rules and other basic safety precautions may result in serious personal injury Save these instructions in a safe place and on hand so that they can be read when required SAFETY INSTRUCTIONS To ensure safe and efficient operation it is essential to read and follow each of these warnings and precautions 1 DO NOT smoke near pump or use pump near an open flame Fire could result 2 Disconnect power to pump before servicing pump 3 Turn off the switch before connecting power 4 Take motors needing service to an authorized repair shop or return to factory to maintain 5 A filter should be used on pump outlet to ensure that no foreign material is transferred to fuel tank 6 Tank or barrel should be anchored to prevent tipping in both the full and empty conditions AN WARNING 1 Electrical wiring should be done a licensed electrician in compliance with local codes Rigid conduit should be used and proper ground must be provided to avoid the possibility of electrical shock Failure to comply with this warning could result in serious injury and or loss of property 2 This product should not be used for fluid transfer into aircraft This product is not suited for use with fluids for human consumption or fluids containing water 3 Extreme operating
3. S Mr KD No Description Qty No Description ow ef Sa i f me je el tent e Hexagon ange bots mo 9 ElectricMotor 1 25 Junctonbox 1 DC Power cable with Fuse Carrier 2 Gaedo a sg o Fis detener 1 2 Omg TA ra Nozziehotler 1 80 Sealedsorew 1 45 nylon setflockingscrew 1 TO is Switchonnecior 11 To
4. rowing in the suction Use tubing suitable for working Check the voltage at the pump Adjust the voltage and or use cables of greater cross section The suction tubing is resting on Raise the tubin Cavitations occurring Reduce suction pressure Irregular functioning of the Dispense until the air is purged Increased pump noise ert by pass from the circuit Air present in the diesel fuel Verify the suction connections Leakage from the pum Check and replace the mechanical 9 oe Seal damaged P body seal Daily Use Excessive suction pressure By pass valve blocked Low rotation speed m f using flexible tubing attach the ends of the tubing to the tanks In the absence of an appropriate slot solidly grasp the delivery tube before beginning dispensing m Before starting the pump make sure that the delivery valve is closed dispensing nozzle or line valve m Turn the ON OFF switch to ON The by pass valve allows functioning with the delivery closed for only brief periods m Open the delivery valve solidly grasping the end of the tubing m Close the delivery valve to stop dispensing m When dispensing is finished turn off the pump MAINTENANCE Under normal working conditions the noise emission from all models does not exceed the value of 80 db at a distance of 1 meter from the electric pump DIGRAM AND PARTS LIST A FOR KIT 1 2 3 auto 4 S Cego me A I B FOR SINGLE PUMP a OG GR de N
5. rrel bung 3 During installation and maintenance make sure that the electric supply lines are not live Always turn off the switch before supplying electrical power 5 Check the correct rotation direction of the DC pump If it is inverted check the polarity of the connection cable a RED cable positive pole b BLACK cable negative pole 6 Systems should be designed to require a minimum amount of suction lift Maximum equivalent feet of lift is 8 for diesel fuel 7 Tank or barrel must be properly vented A water separator should be used for pumping diesel fuel 8 Power to the unit should be supplied from a dedicated 30 amp circuit breaker No other equipment should be powered from this breaker If two pumps are supplied from one breaker that breaker must be capable of handing the load of both motors A PROBLEMS AND SOLUTIONS Check the electrical connections and Lack of electric power the safety systems Check for possible damage or Rotor jams obstruction of the rotating components Motor problems Contact with the service department Low level in the suction tank Refill the tank Foot valve blocked Clean and or replace the valve Filter clogged Clean the filter Lower the pump with respect to the Level High loss of head in the circuit Use shorter tubing or of greater working with the by pass open Diameter Dismantle the valve clean and or replace it Low or no flow rate suction tubing A nar
Download Pdf Manuals
Related Search