Home

ROBO-8719VG2AR User`s Manual

1. A quick review of the basic IRQ mapping is given below for your reference ROF Usable IRQ Diskette Event IRQ 15 It is then very easy to find out which IRQ resource is ready for additional peripherals If IRQ resource is not enough please disable some devices listed above to release further IRQ numbers ROBO 8719VG2AR User s Manual 5 3 Troubleshooting 5 3 FAQ Unboot problem Symptom SBC keeps beeping and no screen has shown Solution In fact each beep sound represents different definition of error message Please refer to table as following Beep sounds Meaning Action One long beep with one DRAM error Change DRAM or reinstall it short beeps One long beep constantly DRAM error Change DRAM or reinstall it One long beep with two Monitor or Display Please check Monitor connector short beeps Card error whether it inserts properly Beep rapidly Power error warning Please check Power mode setting Symptom There is neither no beeps nor screen output Solution Indeed you can do the stand alone to identify the root cause by isolating the board from other possible system devices such as PCI device backplane and so on If the system still cannot boot up please fill out RMA from which is provides on Portwell website and then send back to Portwell as a RMA Besides you also visit RMA site http www portwell com tw rma login asp to check RMA report if necessary Information
2. Palette Snooping Enabled informs the PCI devices that an ISA graphics device is installed in the system so the card will function correctly The choice Disabled Enabled PCTIDE BusMaster Enabled Uses PCI bus mastering for reading writing to IDE drives The choice Disabled Enabled OffBoard PCI ISA IDE Card Some PCI IDE cards may require this to be set to the PCI slot number that is holding the card AUTO Works for most PCI IDE cards The choice Auto PCI Slot1 PCI Slot2 PCI Slot3 PCI Slot4 PCI Slot5 PCI Slot6 IRQ 3 IRO 4 IRQ5 IRQ7 IRQ 9 IRO 10 IRQ 11 IRQ 14 IRQ 15 Available Specified IRQ is available to be used by PCI PnP devices Reserved Specified IRQ is reserved for used by Legacy ISA devices The choice Available Reserved DMA Channel 0 DMA Channel 1 DMA Channel 3 DMA Channel 5 DMA Channel 6 DMA Channel 7 Available Specified DMA is available to be used by PCI PnP devices Reserved Specified DMA is reserved for use by Legacy ISA devices The choice Available Reserved Reserved Memory Size Select Size of memory block to reserve for legacy ISA devices The choice Disabled 16K 32K 64K ROBO 8719VG2AR User s Manual 4 27 BIOS Setup Information 4 5 Boot Use this menu to specify the priority of boot devices BIOS SETUP UTILITY ROBO 8719VG2AR User s Manual 4 28 BIOS Setup Information Boot Settings Configuration SIGS SETUP UTILITT Allows BIOS to skip
3. certain tests uhile Quiet Boot Fisabledi decrease the tine I fidDa SCH Sispley Mode Force SIGS needed to boot ihe Bootup Mem Lock Bak system I PS 2 Monse Support Extol d Wait For Fi if Error Enabled d Hit BEL Message Display fEnabled interrupt 19 Captere Quick Boot Enabling this setting will cause the BIOS power on self test routine to skip some of its tests during boot up for faster system boot The choice Disabled Enabled Quiet Boot This BIOS feature determines if the BIOS should hide the normal POST messages with the motherboard or system manufacturer s full screen logo When it is enabled the BIOS will display the full screen logo during the boot up sequence hiding normal POST messages When it is disabled the BIOS will display the normal POST messages instead of the full screen logo Please note that enabling this BIOS feature often adds 2 3 seconds of delay to the booting sequence This delay ensures that the logo is displayed for a sufficient amount of time Therefore it is recommended that you disable this BIOS feature for a faster boot up time The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 29 BIOS Setup Information AddOn ROM Display Mode This item is used to determine the display mode when an optional ROM is initialized during POST When set to Force BIOS the display mode used by AMI BIOS is used Select Keep Current if you want
4. PCIE Port 0 PCIE Port 1 PCIE Port 2 PCIE Port 3 PCIE Port 4 The choice Auto Disabled Enabled PCIE High Priority Port The choice Disabled Port 0 Port 1 Port 2 Port 3 Port 4 Port 5 PCIE Port 0 PCIE Port 1 PCIE Port 2 PCIE Port 3 PCIE Port 4 PCIE Port 5 IOxAPIC Enabled The choice Disabled Enabled ASF Support The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 40 BIOS Setup Information ME Subsystem Configuration BIOS SETUP UTILITY MECI Message Enabled End OF Post SS HCI Message Enabled ME DELT Configuration ME HECI Enab led ME IDER Disabledi EXT Bisabled Select Screes Select Item Change Opt ion Gereral Hels Save amd Exit Exit BootBlock HECI Message The choice Disabled Enabled HECI Message The choice Disabled Enabled End Of Post S5 HECI Message The choice Disabled Enabled ME IDER The choice Disabled Enabled ME KT The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 41 BIOS Setup Information 4 8 Exit This menu allows you to load the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes BIOS SETUP UTILITY Exit Options Biscard Chamges amd Exit f Discard Charges Load Optimal Befauits d Lead Failsafe Befaults Exit Saving Changes Exit System Setup and save your changes to CMOS Pr
5. 0 5 10 15 20 25 30 35 ATA PI 80Pin Cable Detection Select the mechanism for detecting 80Pin ATA PI cable The choice Host amp Device Host Device Floppy Configuration This Sub Menu contains Setup Items which control configuration of the Internal Graphics Display Device BIDS SETUP UTILITT ROBO 8719VG2AR User s Manual 4 7 BIOS Setup Information Floppy A Select the type of floppy drive connected to the system The choice None 360KB 5 1 4 12MB 5 1 4 720KB 3 1 2 1 44MB 3 1 2 2 88MB 3 1 2 Super IO Configuration BiGS SETUP UTILITT Configure UiuG27BHG Super 10 Chipset or disable Fioppy Controlier Serial Porti Address Serial PoriZ fiidress ETR IRGGI Parallel Port Address 3721 f Paraliel Fort Mode formal i Yaraitel Port IFQ ERA d WtchBog Timer Set fBisabledi Report Chassis Istrution OnBoard Floppy Controller This item allows enable disable onboard Floppy disk controller The choice Disabled Enabled Floppy Drive Swap If the system has two floppy drives choose enable to assign physical driver B to logical drive A and Vice Versa The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 8 BIOS Setup Information Serial Port 1 Port 2 Address Allows BIOS Select Serial Port1 or Port2 Base Addresses The choice Disabled 3F8 IROA 3E8 IRQ4 2E8 IRQ3 Serial Port 2 Mode This item allows users to select Infrared transmission
6. Matrix Storage technology supported by the ICH9ME chip allows you to create a RAID 0 and a RAID 1 set using only two identical hard disk drives The Intel amp Matrix Storage technology creates two partitions on each hard disk drive to create a virtual RAID 0 and RAID 1 sets This technology also allows you to change the hard disk drive partition size without losing any data 3 3 6 AMT Function Installation A major barrier to greater IT efficiency has been removed by Intel amp Active Management Technology Intel AMT a feature on Intel vPro technology Using built in platform capabilities and popular third party management and security applications Intel amp AMT allows IT to better Discover Heal and Protect their networked computing assets Installing ME Management Engine Drivers which includes HECI Driver and LMS SOL Driver and operating PCI serial port and PCI simple communications controller ROBO 8719VG2AR User s Manual 3 6 System Installation 3 4 Clear CMOS Operation The following table indicates how to enable disable CMOS Clear Function hardware circuit by putting jumpers at proper position 1 1 2 C 2 3 O 3 Normal Clear 1 2Short Normal Operation 2 3 Short Clear CMOS contents 3 5 WDT Function The working algorithm of the WDT function can be simply described as a counting process The Time Out Interval can be set through software programming The availability of the time out interval settin
7. BIOS SETUP UTILITY ACPI Settings gt Advanced ACFI Cosfiguration I Chipset MFI Configuration ROBO 8719VG2AR User s Manual 4 11 BIOS Setup Information General ACPI Configuration BIOS SETUP UTILITY Suspend mode This item specifies the power saving modes for ACPI function If your operating system supports ACPI you can choose to enter the Standby mode in S1 POS or 53 STR fashion through the setting of this field Options are 91 POS The S1 sleep mode is a low power state In this state no system context is lost CPU or chipset and hardware maintains all system contexts S3 STR The S3 sleep mode is a lower power state where the information of system configuration and open applications files is saved to main memory that remains powered while most other hardware components turn off to save energy The information stored in memory will be used to restore the system when a wake up event occurs ROBO 8719VG2AR User s Manual 4 12 BIOS Setup Information Advanced ACPI Configuration Advanced ACPI Configuration settings Use this section to configure additional ACPI options BIUS SETUP UTILITT Emable ZSSP poisters ta 64 bit Fixed System Description Tables Di fKPI version has some ACPI Version Features Enable RSDP pointers to 64 bit Fixed System Description Tables The choice ACPI v1 0 ACPI v2 0 ACPI v3 0 ACPI APIC support Include ACPI APIC table pointer to RSDT pointer
8. Exit Memory Remap Feature Enabled Allow remapping of overlapped PCI memory above the total physical memory Disabled Do not allow remapping of memory The choice Disabled Enabled DRAM Frequency Users are recommended to use Auto for memory frequency selection The choice Auto 533 667 800 1067 MHz Configure DRAM Timing by SPD This option provides DRAM plug and play support by serial presence detect SPD mechanism via the system management bus SMBUS interface The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 35 BIOS Setup Information Memory Hole In order to improve performance certain space in memory is reserved for ISA cards This memory must be mapped into the memory space below 16MB The choice Disabled 15MB 16MB Initiate Graphic Adapter Select which graphics controller to use as the primary boot device The choice IGD PCI IGD PCI PEG PEG IGD PEG PCI Internal Graphics Mode Select Select the amount of system memory used by the internal graphics device The choice Enabled 32MB Enabled 64MB Enabled 128MB PEG Port This setting allows you to select whether to use the on chip graphics processor or the PCI Express card When set to Auto the BIOS checks to see if a PCI Express graphics card is installed If it detects that a PCI Express graphics card is present the motherboard boots up using that card Otherwise it defaults to the onboard graphics processor The cho
9. JP11 CF Power Select IP VCC3 ROBO 8719VG2AR User s Manual 2 2 Hardware Configuration 2 2 Connectors I O peripheral devices and Flash disk will be connected to these interface connectors 3 4P Power Connector for CPU POWER 12V Keyboard amp Mouse Connector ATX Standby Power Connector J10 Miscellaneous Header Pin2 4 6 Power LED Pin9 11 Power Button Pin13 15 Reset Button Pin14 16 HDD LED fe sd ES ES m JT DDR 240pin Stott ME initialization mt Dual Port USB Connector O Ta SBtGPOHede OO mme usono E 118 21 22 SATA Interface Connector lt ji9 SP FAN Power Connector Gystemi J20 sPFANPoweConedor CPU ps EDS Conectar O p AudoHede To jy DsUBBSVGACometr ps SDVO Board To Board Connector J29 LVDS Panel Back light Power Connector Ei 5P FAN Power Connector System jst ISA Golden Finger OOOO O 9 Compact Flash Socket s PdGodeigr M CASE OPEN detection O o 17 23 RJ45 LAN Port 1 2 ROBO 8719VG2AR User s Manual 2 3 Hardware Configuration Pin Assignments of Connectors J1 FDD Interface Connector 5 Greud X 6 7 Greud 8 NDX 9 Geud 10 MOA 19 Grou
10. Setup Information Prima Secondary Third Fourth IDE Master Slave While entering setup BIOS auto detects the presence of IDE devices This displays the status of auto detection of IDE devices Auto Type Press PgUp lt gt or PgDn lt gt to select Manual None or Auto type you can use Manual to define your own drive type manually LBA Large Mode Enabling LBA causes Logical Block Addressing to be used in place of Cylinders Heads and Sectors Block Multi Sector Transfer Any selection except Disabled determines the number of sectors transferred per block PIO Mode Indicates the type of PIO Programmed Input Output DMA Mode Indicates the type of Ultra DMA S M A R T This allows you to activate the S M A R T Self Monitoring Analysis amp Reporting Technology capability for the hard disks S M A R T is a utility that monitors your disk status to predict hard disk failure This gives you an opportunity to move data from a hard disk that is going to fail to a safe place before the hard disk becomes offline 32 Bit Data Transfer Enable Disable 32 bit Data Transfer ROBO 8719VG2AR User s Manual 4 6 BIOS Setup Information Hard Disk Write Protect Disabled Enabled device write protection this will be effective only if device is accessed through BIOS The choice Disabled Enabled IDE Detect Time Out Sec Select the time out value for detecting ATA ATAPI device s The choice
11. User s Manual 1 6 Hardware Configuration Chapter 2 Hardware Configuration This chapter gives the definitions and shows the positions of jumpers headers and connectors All of the configuration jumpers on ROBO 8719VC2AR are in the proper position The default settings shipped from factory are marked with an asterisk 2 1 Jumper Setting In general jumpers on the single board computer are used to select options for certain features Some of the jumpers are designed to be user configurable allowing for system enhancement The others are for testing purpose only and should not be altered To select any option cover the jumper cap over SHORT or remove NC it from the jumper pins according to the following instructions Here NC stands for Not Connect NEUE l D u Figure 2 1 ROBO 8719VG2AR Jumper and Connector Locations P1 Auto Power Button selection Auto power button mode 13 COM2 RS232 485 422 Selection RS232 5 69 11 10 12 15 17 16 18 RS485 1 2 7 9 8 10 19 20 RS422 3 4 7 9 8 10 13 15 14 16 21 22 ROBO 8719VG2AR User s Manual 2 1 Hardware Configuration JP6 RTC CMOS Clear Jumper Setting Normal Operation Clear CMOS Contents JP7 AT ATX Power Supply Selection 3 5 4 6 ATX Power Supply 1 3 2 4 AT Power Supply JP8 TPM Physical Presence TPM Enable JP9 LVDS Back light Power Level JP10 LVDS Power Level
12. amp Support Question Intel GM45 Chipset supports Dual Channel Mode but how can I enable this function Answer Indeed you don t have to change any setting You can simply plug DDR2 SDRAM Module on DIMMs and then system will automatically enable Dual Channel Mode Question What kind of CPU supports Hyper Threading Answer All FSB 1066 800 533 MHz series CPU support Hyper Threading mode Question Why cannot l install USB 2 0 driver Answer If you are using Windows 2000 you need to update your Service Pack version to Service Pack 4 If you are using Windows XP you need to update Service Pack to Service Pack 1 at least ROBO 8719VG2AR User s Manual 5 4 Troubleshooting To solve this problem you can download BIOS from our website http www portwell com tw download as If you cannot find BIOS that you need please contact with Technical Support Department to request a new BIOS to solve this problem Technical Support Department Mailto tsd portwell com tw Question I forget my password of system BIOS what am I supposed to do Answer You can simply short 2 3 pins on JP4 to clean your password Note Please visit our technical web site at http www portwell com tw For additional technical information is not covered in this manual ROBO 8719VG2AR User s Manual 5 5 Appendix A System Memory Address Map Each On board device in the system is assigned a set of memory addresses which also can be identica
13. chipset that a few old operating systems might not be able to recognize To overcome this compatibility issue for Windows Operating Systems such as Windows 2000 XP Server 2003 please install its INF before any of other Drivers are installed You can find very easily this chipset component driver in ROBO 8719 CD title 3 3 2 Intel amp Integrated Graphics GMCH Chip Using GMCH High performance graphic integrated chipset Intel GMA 4500MHD is aimed to gain an outstanding graphic performance Shared 128 accompany it to 256MB Maximum system DDR2 SDRAM with Total Graphics Memory This combination makes ROBO 8719 an excellent piece of multimedia hardware With no additional video adaptor this onboard video will usually be the system display output By adjusting BIOS of Advanced Chipset Feature and set PEG Onchip VGA Control to PEG Port please kindly refer section 4 6 of chapter 4 configuration and then the add on PCI or PCI Express by 16 VGA Card can take over the system display Drivers Support Please find hardware driver of GM45 in the ROBO 8719 CD title Drivers support Windows 2000 XP System 32 bit amp Windows XP System 64 bit Windows 2000 XP 32bit Please execute Install for Windows 2000 XP System 32 Bit file to start graphics driver installation Windows XP 64 bit Please execute Install for Windows XP System 64 bit file to start graphics driver installation 3 3 3 On board Fast Ethernet Controller Drivers Supp
14. two PNP I O port addresses that can be used to configure WDT 1 0x2E EFIR Extended Function Index Register for identifying CR index number 2 0x2F EFDR Extended Function Data Register for accessing desired CR Below are some example codes which demonstrate the use of WDT Enter W83627DHG configuration registers mode outp Ox2E 0x87 outp Ox2E 0x87 Assign Pin77 to be WDTO outp Ox2E Ox2D outp Ox2E 1 inp 0x002E 1 amp OxFE Select logic device 8 outp Ox2E 0x07 outp Ox2E 1 0x08 Select Count Mode Minute or Second outp 0x002E OxF5 outp 0x002F inp 0x002F amp OxF7 Count mode Register amp 0x08 Specify Time out Value outp 0x002E OxF6 outp 0x002F Time out Value Register Disable WDT reset by keyboard mouse interrupts outp 0x002E OxF7 outp 0x002F 0x00 Exit Extended Function Mode outp 0x002E 0xAA Definitions of Variables Value of Count mode Register 1 0x00 Count down in seconds Bit3 0 2 0x08 Count down in minutes Bit3 1 Value of Time out Value Register 1 0x00 Time out Disable 2 0x01 OxFF Value for counting down ROBO 8719VG2AR User s Manual 3 8 System Installation 3 6 GPIO The ROBO 8719VG2AR provides 8 programmable input or output ports that can be individually configured to perform a simple basic I O function Users can configure each individual port to become an input or output port by programming regist
15. B Steno 256MB FDD MITSUMI D353M3D 1 44MB CDROM LITE ON LH 20A15 Power Supply FSP400 60PFN Back plane PBP 14A7 A 305 Operating Temperature 0 C 60 C Storage Temperature 20 C 80 C Relative Humidity 5 90 non condensing ROBO 8719VG2AR User s Manual System Overview 1 3 1 Mechanical Drawing ie NN NIAAA ANAS 149 58 ROBO 8719VG2AR User s Manual System Overview 1 4 System Architecture All of details operating relations are shown in ROBO 8719VG2AR series System Block Diagram IMVP VI LVDS connector CRT connector SDVO connector Optional 82567 PHY chip 82574L LAN chip AUDIO CODEC HI i AY Penryn Maron Socket P CK505 FSB 667 800 1066 MHz Internal RGB SDVO B Cantiga GM45 11 0082 667 800 MHz 0082 667 800 MHz HDA Bus ICH9ME PCI Bus PCI to ISA bridge W83628AG W83629AG USB Bus USB port x6 SATA Bus SATA port x3 SATA Bus TPM header 8bit GPIO header 1 JMD330 PA A SPI ROM HW monitor W83627DHG FDD amp Parallel Port PICMG BP CF Card COM port x2 PS 2 header ROBO 8719VG2AR System Block Diagram ROBO 8719VG2AR
16. OBO 8719VG2AR User s Manual 4 30 BIOS Setup Information When disabled the ROM BIOS of these host adaptors will not be able to cap ture Interrupt 19 Therefore you will not be able to boot operating systems from any bootable disks attached to these host adaptors Nor will you be able to gain access to their ROM setup utilities The choice Disabled Enabled Boot Device Priority S SETUP UTILITY Disabled 1st Boot Device The items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system First press lt Enter gt to enter the sub menu Then you may use the arrow keys f to select the desired device then press lt gt lt gt or lt PageUp gt lt PageDown gt key to move it up down in the priority list The choice Removable Dev Disabled ROBO 8719VG2AR User s Manual 4 31 BIOS Setup Information Removable Drives BIOS SETUP UTILITY Disabled 1st Drive This setting allows users to set the priority of the removable devices First press Enter to enter the sub menu Then you may use the arrow keys f to select the desired device then press lt gt lt gt or lt PageUp gt lt PageDown gt key to move it up down in the priority list The choice 1st FLOPPY DRICE Disabled ROBO 8719VG2AR User s Manual 4 32 BIOS Setup Information 4 6 Security Use this menu to set supervisor and user passwords SIGS SETUP UTILITY Secur
17. PIO Onboard programmable 8 bit Digital I O interface Cooling Fans Support two 3 pin header for system fan and one 3 pin header for CPU fan System Monitoring Feature Monitor system temperature and major power sources etc Bracket Support dual Ethernet port with 2 indicators dual USB ports and one CRT port Outline Dimension L X W 338 5mm 13 33 X 122mm 4 8 Power Requirements Power Consumption test Run Burning Test V5 3 RUN time 10 30 Minutes 12 CPU 1 6A 12V System O 2 0A 5V System 9 5 4A ROBO 8719VG2AR User s Manual 1 3 System Overview Configuration CPU Type SBC BIOS Memory VGA Card VGA Driver LAN Card LAN Driver Audio Card Audio Driver Genuine Intel CPU 2 53GHz T9400 ES FSB 1066MHz Portwell Inc ROBO 8719VG2AR BIOS Rev R1 00 E0 Apacer DDR2 667 2GB 2 ELPIDA E1108ACBG 8E E Onboard Intel amp 4 Series Express Chipset Family Intel 4 Series Express Chipset Family Version 6 14 10 5002 Onboard Intel amp 82567LM 82574L Gigabit Network Intel amp 82567LM 82574L Gigabit Network Onboard Realtek ALC262 High Definition Audio Controller Realtek ALC262 High Definition Audio Version 5 10 0 5735 Chip Driver Intel Chipset Device Software Version 9 0 0 1009 USB 2 0 Driver Intel Family USB2 Enhanced Host Controller SCSI Card Adaptec ASC 29160LP SCSI HDD Seagate ST39173W 8 47GB SATA HDD WD WD1601ABYS 160GB Compact Flash Apacer AP CF256
18. ROBO 8719VG2AR Single Board Computer User s Manual Version 1 0 Copyright Portwell Inc 2009 All rights reserved All other brand names are registered trademarks of their respective owners Preface Table of Contents How to Use This Manual Chapter 1 System 0 6 61 1 1 1 1 Introduction eau sa Ue ee at et te i 1 1 1 2 Check dst uere eter eii te ROT era et Ut qot iot Ie echt aa 1 2 1 3 Product Specification tn Sik etel Mr pete e de b t s 1 2 1 3 1 Mechanical Drawing ool etr extis peii er lictor eie RS 1 5 1 4 System E 1 6 Chapter 2 Hardware Configuration 2 1 2 Jumper EE 2 1 2 2 CONNECT Sida dat ee to EEEE 2 3 Chapter 3 System 0 3 1 a CR BEE 3 1 9 2 Main Memory ien aet nee pea e evans petet ceret Id dates aks dt 3 2 3 3 Installing the Single Board Computer ENEE 3 3 3 3 Chipset Component Driver rere ud teet o rta iio pias 3 4 3 3 2 Intel Integrated Graphics GMCH Chip esses 3 4 3 3 3 On board Fast Ethernet Controller AE 3 4 3 3 4 On board AC 97 Audio Device 3 5 3 3 5 Intel Matrix Storage Man
19. abled Disabled Mibi USB Functions This setting specifies the function of the onboard USB controller The choice Disabled 2 USB Ports 4 USB Ports 6 USB Ports 8 USB Ports 10 USB Ports 12 USB Ports USB Port Configure The choice 6x6 USB Ports 8x4 USB Ports USB 2 0 Controller Set to Enabled if you need to use any USB 2 0 device in the operating system that does not support or have any USB 2 0 driver installed such as DOS and SCO Unix GbE Controller This setting Enable the onboard Gigabit Ethernet controller GbE LAN Boot When Enabled the BIOS attempts to boot from a LAN boot image before it attempts to boot from a local storage device The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 39 BIOS Setup Information 82574 Wake Up From S5 This field specifies whether the system will be awakened from the S5 power saving mode when activity or input signal of onboard LAN is detected The choice Disabled Enabled HDA Controller This setting controls the High Definition Audio interface integrated in the Southbridge The choice Disabled Enabled SMBUS Controller The choice Disabled Enabled SLP S44 Min Assertion Width The choice 4 to 5 seconds 3to 4 seconds 2 to seconds 1 to 2 seconds Restore on AC Power Loss This item allows user to configure the power status of using ATX power supply after a serious power loss occurs The choice Power Off Power On Last State
20. ager Device 3 5 9 3 6 AMT Function Installation ne ane de ete ee D e cite erg 3 6 3 4 Clear CMOS Operation te ether edema obra etm doeet 3 7 5 5 WDT Tunction tne euh eer mh EUR Rer Re re intd 3 7 D6 GPIO eese erae etedtaiidei ean 3 9 3 6 1 Pin assignment aieia nec telae tente heated te e PIE oed 3 9 3 6 2 ROBO 8719VG2AR GPIO Programming Guide 3 9 9 633 Example i etu a ep eere i a 3 11 Chapter 4 BIOS Setup 0 4 1 4 1 Entering Setup Launch System Setup 4 1 ALMA EE 4 2 4 3 Advanced seasoned doe RO t eode ee i ep e e e otn 4 3 EE 4 25 a Mid 4 28 BO eina PE EE 4 33 AT EE 4 34 LO re ere dte Reit an ceps 4 42 Chapter 5 Troubleshooting 5 1 531 Hardware Quick Installation iodo at bat 5 1 J2 BIOS Oi AA AAA Ao 5 2 DB FAO n M 54 Appendix A Appendix B Preface How to Use This Manual The manual describes how to configure your system board to meet various operating requirements It is divided into five chapters with each chapter addressing a basic concept and operation of Single Host Board Chapter 1 System Overview Presents what y
21. ame model and capacity when creating a disk array To install the SATA hard disks for a RAID configuration 1 Install the SATA hard disks into the drive bays 2 Connect the SATA signal cables 3 Connect a SATA power cable to the power connector on each drive Intel amp RAID configurations This ROBO 8719 supports RAID 0 RAID 1 and Intel amp Matrix Storage configurations for Serial ATA hard disks drives through the Intel amp ICH9ME Southbridge chip ROBO 8719VG2AR User s Manual 3 5 System Installation RAID configurations RAID 0 Data striping optimizes two identical hard disk drives to read and write data in parallel interleaved stacks Two hard disks perform the same work as a single drive but at a sustained data transfer rate double that of a single disk alone thus improving data access and storage Use of two new identical hard disk drives is required for this setup RAID 1 Data mirroring copies and maintains an identical image of data from one drive to a second drive If one drive fails the disk array management software directs all applications to the surviving drive as it contains a complete copy of the data in the other drive This RAID configuration provides data protection and increases fault tolerance to the entire system Use two new drives or use an existing drive and a new drive for this setup The new drive must be of the same size or larger than the existing drive Intel Matrix Storage Manager The Intel
22. e message below appears on the screen press Del key to enter Setup Press Del to enter SETUP If the message disappears before you respond and you still wish to enter Setup restart the system by turning it OFF and On or pressing the RESET button You may also restart the system by simultaneously pressing Ctrl Alt and Delete keys Press F1 to Run SETUP or Resume The BIOS setup program provides a General Help screen You can call up this screen from any menu by simply pressing F1 The Help screen lists the appropriate keys to use and the possible selections for the highlighted item Press lt Esc gt to exit the Help screen General Help lt Select Screen TL Select Item Change Option Field Enter Go to Sub Screen PGDN Next Page PGUP Previous Page HOME Go to Top of Screen END Go to Bottom of Screen F2 F3 Change Colors F Discard Changes F6 Load Failsafe Defaults F9 Load Optimal Defaults F10 Save and Exit ESC Exit ROBO 8719VG2AR User s Manual 4 1 BIOS Setup Information 4 2 Main Use this menu for basic system configurations such as time date etc Use ENTERO or SHEFT TABI to select a field System Overview I Version 08 60 16 d Build Bate 18 05 05 ID LARS i Processor I Gemine Intel CPU e 2 539 i Speed Bet k i Count Si po 2 Size D Zeil Be Il wr 13 to configure iem Time fe Select Screen n Select item Change F
23. ease system performance To enable Dual Channel DDR2 memory technology you have to install dual identical memory modules in both memory sockets Following tables show bandwidth information of different processor and memory configurations MERO ENIM Dual Channel DDR Single Channel DDR ned y Bandwidth Bandwidth 800MHz 25 6 GB s 12 8 GB s 667 MHz 21 2 GB s 10 6 GB s Note To maintain system stability don t change any of DRAM parameters in BIOS setup to upgrade your system performance without acquiring technical information CPU FSB Memory Frequency synchronization Support different memory frequencies depending on the CPU front side bus and the type of DDR2 DIMM Watch Out it s meaning that memory maximum frequency on configuration which is synchronization and based on CPU FSB CPU FSB Memory Frequency 1066MHz 533 667 800MHz 800 MHz 533 667 800MHz 3 3 Installing the Single Board Computer To install your ROBO 8719 into standard chassis or proprietary environment you need to perform the following Step 1 Check all jumpers setting on proper position Step 2 Install and configure CPU and memory module on right position Step 3 Place ROBO 8719 into the dedicated position in your system Step 4 Attach cables to existing peripheral devices and secure it ROBO 8719VG2AR User s Manual 3 3 System Installation 3 3 1 Chipset Component Driver The chipset on ROBO 8719 is a new
24. eeds to be written into EFER first Then the data will be read written from to EFDR To R W W83627HG CR it is needed to Enter Enable Configuration Mode first When completing the programming it is suggested to Exit Disable Configuration Mode Enter Configuration Mode Write 87h to IO port EFER twice Exit Configuration Mode Write AAh to IO port EFER ROBO 8719VG2AR User s Manual 3 10 System Installation 3 6 3 Example void enter Superio2 CFG void outportb Ox2E 0x87 outportb 0x2E 0x87 void exit Superio2 CFG void j outportb 0x2E OxAA void Set CFG2 unsigned char Addr2 unsigned char Value2 unsigned char d2 outportb 0x2E Addr2 delay 2 outportb 0x2E 1 Value2 delay 2 j unsigned char Get CFG2 unsigned char Addr2 unsigned char d2 outportb 0x2E Addr2 delay 2 d2 inportb 0x2E 1 delay 2 return d2 j int main void unsigned char d2 enter Superio2 CFG CR2A B7 1 selet GPIO Port 1 d2 Get CFG2 0x2A 02 d2 amp Ox7F 0x80 Set CFG2 0x2A 02 ROBO 8719VG2AR User s Manual 3 11 System Installation IO test loop 1 Set GPIO Port 1 of Superio 2 Enable Set CFG2 0x07 0x07 Select logic device 07 of Superio2 Set_CFG2 0x30 0x01 Enable GPIO Port 1 of Superio2 IO test loop 1 Set GPIO Port 1 of Superio2 Enable Set CFG2 0x07 0x07 Select logic device 07 Set CFG2 0xF0 OxOF GPIO Po
25. er bit of I O Selection To invert port value the setting of Inversion Register has to be made Port values can be set to read or write through Data Register 3 6 1 Pin assignment 13 General Purpose I O Connector PIN No Signal Description 1 General Purpose I O Port 0 GPIOO General Purpose I O Port 1 GPIO1 General Purpose I O Port 2 GPIO2 General Purpose I O Port 3 GPIO3 Ground General Purpose I O Port 4 GPIO4 7 General Purpose I O Port 5 GPIO5 General Purpose I O Port 6 GPIO6 General Purpose I O Port 7 GPIO7 5V All General Purpose I O ports can only apply to standard TTL 5 signal level OV 5V and each source sink capacity up to 12mA 3 6 2 ROBO 8719VG2AR GPIO Programming Guide There are 8 GPIO pins on ROBO 8719VG2AR These GPIO pins are from SUPER I O W83627DHG GPIO pins and can be programmed as Input or Output direction J13 pin header is for 8 GPIO pins and its pin assignment as following 13 Pin12GPIO0 from SUPER I O_GPIO30 with Ext 2 2K PH J13_Pin2 GPIO1 from SUPER I O GPIO31 with Ext 2 2K PH 13 Pin32GPIO2 from SUPER I O GPIO32 with Ext 2 2K PH J13_Pin4 GPIO3 from SUPER I O_GPIO33 with Ext 2 2K PH J13_Pin6 GPIO4 from SUPER I O GPIO34 with Ext 2 2K PH J13_Pin7 GPIO5 from SUPER I O GPIO35 with Ext 2 2K PH 13 Pin82GPIO6 from SUPER I O GPIO36 with Ext 2 2K PH 13 Pin9 GPIO7 from SUPER I O GPIO37 with Ext 2 2K PH lt lt lt lt lt Be careful Pin5 GND Pinl0 VCC
26. essing Enter on this item asks for confirmation Save changes to CMOS and exit the Setup Utility Discard Changes and Exit Abandon all changes and exit the Setup Utility Discard Changes Abandon all changes and continue with the Setup Utility Load Optimal Defaults Use this menu to load the default values set by the SBC manufacturer specifically for optimal performance of the SBC ROBO 8719VG2AR User s Manual 4 42 BIOS Setup Information Load Failsafe Defaults Use this menu to load the default values set by the BIOS vendor for stable system performance ROBO 8719VG2AR User s Manual 4 43 Troubleshooting Chapter 5 Troubleshooting This chapter provides a few useful tips to quickly get ROBO 8719 running with success As basic hardware installation has been addressed in Chapter 2 this chapter will primarily focus on system integration issues in terms of BIOS setting and OS diagnostics 5 1 Hardware Quick Installation Backplane ROBO 8719 is a full sized Signal Board Computer and therefore is only able to run on PICMG 1 0 backplane To know whether your backplane is PICMG 1 0 backplane please contact with vendor or manufacturer P4 Power connector The CPU supplementary Power Connector J3 has to be connected to a system all the time no matter using ATX mode Otherwise the system won t boot up properly Serial ATA Hard Disk employment Each Serial ATA channel can only connect to one SATA hard disk at a time the
27. g system To find out which version to use consult the vendor of your operating system The choice 1 1 1 4 ROBO 8719VG2AR User s Manual 4 20 BIOS Setup Information PCI Express Configuration Configure PCI Express Support BIOS SETUP UTILITY Active State Power Management PCI Express LOs and L1 link power states The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 21 BIOS Setup Information Smbios Configuration SMBIOS Configuration Menu os Configuration Screen Smbios Smi Support SMBIOS SMI Wrapper support for PnP Func 50h 54h The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 22 BIOS Setup Information Remote Access Configuration BIS SETUP UTILITY Redirection After EIOS POST d terminal Type d UI UIFS Combo Key Sepport i Sredir Memory Bispley Beiag Remote Access Select Remote Access type The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 23 BIOS Setup Information USB Configuration BIOS SETUP UTILITY Module Version 2 24 3 13 4 USB Devices Enabled i 1 Keyboard USS 2 8 Controller Mode BIOS BKI Hasd Dff Legacy USB Support Set to Enabled if you need to use any USB 1 1 2 0 device in the operating system that does not support or have any USB 1 1 2 0 driver installed such as DOS and SCO Unix The choice Disabled Enabled Auto USB 2 0 Controller Mode This setting specifies the operation mode of
28. gs by software or hardware varies from boards to boards ROBO 8719VG2AR allows users control WDT through dynamic software programming The WDT starts counting when it is activated It sends out a signal to system reset or to non maskable interrupt NMI when time out interval ends To prevent the time out interval from running out a re trigger signal will need to be sent before the counting reaches its end This action will restart the counting process A well written WDT program should keep the counting process running under normal condition WDT should never generate a system reset or NMI signal unless the system runs into troubles The related Control Registers of WDT are all included in the following sample program that is written in C language User can fill a non zero value into the Time out Value Register to enable refresh WDT System will be reset after the Time out Value to be counted down to zero Or user can directly fill a zero value into Time out Value Register to disable WDT immediately To ensure a successful accessing to the content of desired Control Register the sequence of following program codes should be step by step run again when each register is accessed Additionally there are maximum 2 seconds of counting tolerance that should be considered into user application program For more information about WDT please refer to Winbond W83627DHG data sheet ROBO 8719VG2AR User s Manual 3 7 System Installation There are
29. gt gt gt gt gt ROBO 8719VG2AR User s Manual 3 9 System Installation There are several Configuration Registers CR of W83627DHG needed to be programmed to control the GPIO direction and status GPI value GPO CROOh CR2F are common global registers to all Logical Devices LD in W83627HG CRO7h contains the Logical Device Number that can be changed to access the LD as needed LD7 contains the GPIO10 17 registers Programming Guide Step1 CR2C Bit 7 5 P 1 1 1 to select multiplexed pins as GPIO32 34 pins Step2 LD7_CRO7h P 09h Point to LD9 Step3 LD7_CR30h_Bit1 P1 Enable GPIO3 Step4 Select GPIO direction Get Status or output value LD9 CRFOh GPIO37 30 direction 1 input 0 output pin LD9 CRF2h P 00h Let CRF1 GPIO data port non invert to prevent from confusion LD9_CRF1h GPIO37 30 data port for input pin get status from the related bit for output pin write value to the related bit For example LD9 CRFOh Bd PO Let GPIO34 as output pin LD9 CRE2h Bit4 P0 Let CRF1 Bit4 non inverted LD9 CRF1h Bd PU Output 0 to GPIO34 pin J13_Pin1 LD9_CRFOh_Bit0 P1 Let GPIO30 as input pin LD9_CRF2h_Bit0 P0 Let CRF1_Bit0 non inverted Read LD9 CRF1h Bit0 Read the status from GPIO30 pin J13_Pin2 How to access W83627DHG CR In ROBO 8719VG2AR the EFER 002Eh and EFDR 002Fh EFER and EFDR are 2 IO ports needed to access W83627HG CR EFER is the Index Port EFDR is the Data Port CR index number n
30. ice Auto Disabled ROBO 8719VG2AR User s Manual 4 36 BIOS Setup Information Video Function Configuration BIOS SETUP UTILITY DVMT Mode Select Intel amp s Dynamic Video Memory Technology DVMT allows the system to dynamically allocate memory resources according to the demands of the system at any point in time The key idea in DVMT is to improve the efficiency of the memory allocated to either system or graphics processor It is recommended that you set this BIOS feature to DVMT Mode for maximum performance Setting it to DVMT Mode ensures that system memory is dynamically allocated for optimal balance between graphics and system performance The choice Fixed Mode DVMT Mode DVMT FIXED Memory When set to DVMT FIXED Mode the graphics driver will allocate a fixed amount of memory as dedicated graphics memory as well as allow more system memory to be dynamically allocated between the graphics processor and the operating system The choice 128MB 256MB ROBO 8719VG2AR User s Manual 4 37 BIOS Setup Information Boot Display Device Use the field to select the type of device you want to use as the display s of the system The choice CRT SDVO CRT SDVO LVDS CRT LVDS on Port 0 Spread Spectrum Clock The choice Disabled Enabled South Bridge Configuration ROBO 8719VG2AR User s Manual 4 38 BIOS Setup Information BIOS SETUP UTILITY Vu uto E Disabled Disabled Disabled Disabled Dis
31. ield Tab Select Field System Bate AMI BIOS Processor System Memory These items show the firmware and hardware specifications of your system Read only System Time The time format is Hour Minute Second Use or to configure system Time System Date The date format is lt Day gt lt Month gt lt Date gt lt Year gt Use or to configure system Date ROBO 8719VG2AR User s Manual 4 2 BIOS Setup Information 4 3 Advanced Use this menu to set up the items of special enhanced features Advanced Settings gt IBE Configuration I Floppy Conf igeratice I API Configuration f gt ACI Configuration i REM Configuration I SSF Cenfigsratios gt Configuratica d gt Smbios Corfiguratios gt Trusted Competing ROBO 8719VG2AR User s Manual WARMING Setting wrong values in below sections i may cause system to malfunction gt Superl0 Configuration I Hardware Health Cosfigzratica gt Intel AN Configuration I FCI Express Cosfiguration i gt Remcte ficcess Configuration 4 8 BIOS Setup Information CPU Configuration These items show the advanced specifications of your CPU Read only specific application Execute Disable Bit Capability Disabled force the XD feature flag to always return 0 The choice Disabled Enabled PECI When enabled enables PECI interface The choice Disabled E
32. ity Settings Supervisor Password Installed User Password Mot Imstalled Change User Password Boot Sector Uires Protection Bisabledi Supervisor Password Change Supervisor Password Supervisor Password controls access to the BIOS Setup utility These settings allow you to set or change the supervisor password User Password Change User Password User Password controls access to the system at boot These settings allow you to set or change the user password Boot Sector Virus Protection Boot Sector Virus Protection The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 33 BIOS Setup Information 4 7 Chipset This menu controls the advanced features of the onboard Northbridge and Southbridge BIOS SETUP UTILITT WARMING Setting wrong values in below sections may cause system to malfunction gt South Bridge Configuration gt ME Subsystem Configuration ROBO 8719VG2AR User s Manual 4 34 BIOS Setup Information North Bridge Configuration Bisabled TM Thermal Memory Reference Code MIRO Catastrophic TS on DIM Disabled Boots Graphic Adapter Priority IPES RCH d Internal Graphics Mode Select fEnsbied 17781 i ax TELES 36 Bytes fEnabied gt Select Screen DH Select item Extol Change Optica D Fi General Help FIG Save and Exit i gt Video Fenction Configerat ica EX
33. l of the device The following table lists the system memory address used Memory Area Size Device Description 000 003F 1K Interrupt Area 0040 004F 0 3K BIOS Data Area 0050 006F 0 5K System Data 0070 0E2E 54K DOS OE2F OF6B 5K Program Area OF6C 9B7F 560K Available First Meg Conventional memory end at 636K 9B80 9BBF 1K Extended BIOS Area 9BCO 9FFF 17K Unused A000 AFFF 64K VGA Graphics B000 B7FF 32K Unused B800 BFFF 32K VGA Text C000 CFDF 63K Video ROM CFEO EFFF 128K Unused F000 FFFF 64K System ROM ROBO 8719VG2AR User s Manual Appendix B Interrupt Request Lines IRQ Peripheral devices can use interrupt request lines to notify CPU for the service required The following table shows the IRQ used by the devices on board IRO Current Use Default Use IRO 0 System ROM System Timer IRO 1 System ROM Keyboard Event IRO2 Unassigned Usable IRQ IRO3 System ROM COM2 IRO 4 System ROM COMI IRO 5 Unassigned Usable IRQ IRO 6 System ROM Diskette Event IRQ 7 Unassigned Usable IRQ IRQ 8 System ROM Real Time Clock IRQ 9 Unassigned Usable IRQ IRQ 10 Unassigned Usable IRQ IRQ 11 Unassigned Usable IRQ IRQ 12 System ROM IBM Mouse Event IRQ 13 System ROM Coprocessor Error IRQ 14 System ROM Hard Disk Event IRQ 15 Unassigned Usable IRQ ROBO 8719VG2AR User s Manual
34. lect the type of device connected to the system The choice Auto Not Installed S M A R T This allows you to activate the S M A R T Self Monitoring Analysis amp Reporting Technology capability for the hard disks S M A R T is a utility that monitors your disk status to predict hard disk failure This gives you an opportunity to move data from a hard disk that is going to fail to a safe place before the hard disk becomes offline The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 16 BIOS Setup Information APM Configuration Select for APM Configuration BIOS SETUP UTILITY APN Configuration Enable or disable sen d Restore on AC Power loss Video Power Som Mode d Hard Pisk Power 3oum Mode Throttle Siew Clock fatio System Thermal Resume Gs FTC flare Bisabledi Select Screen Select item Power Management APM Enabled or Disable APM Mode The choice Disabled Enabled Video Power Down Mode Select Power Down video in Suspend or Standby Mode The choice Disabled Suspend Hard Disk Power Down Mode Select Power Down Hard Disk in Suspend or Standby Mode The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 17 BIOS Setup Information Suspend Time Out Go into Suspend in the specified Time The choice Disabled 1 Min 2 Min 4 Min 8 Min 10 Min 20 Min 30 Min 40 Min 50 Min and 60 Min Throttle Slow Clock Ratio Select the Du
35. list The choice Disabled Enabled AMI OEMB table Include OEMB table pointer to R X SDT pointer list The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 13 BIOS Setup Information Headless mode Enable Disable Headless operation mode through ACPI The choice Disabled Enabled Chipset ACPI Configuration Chipset ACPI related Configuration settings Use this section to configure additional ACPI options BIUS SETUP UTILITT Emable S59 poisters te 64 bit Fixed System Bescription Tabies Di fKPI version has some Energy Lake Feature Select the ACPI state used for System Suspend The choice Disabled Enabled APIC ACPI SCI IRO Enable Disable APIC ACPI SCI IRQ The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 14 BIOS Setup Information USB Device Wake From S3 S4 Enable Disable USB device Wake from 53 54 mode The choice Disabled Enabled High Performance Event Time The choice Disabled Enabled AHCI Configuration Select for AHCI Configuration BIUS SETUP UTILITT AHCI CD DVD Boot Time out Some SATA CD DVD in AHCI mode need to wait ready longer The choice 0 5 10 15 20 25 30 35 ROBO 8719VG2AR User s Manual 4 15 BIOS Setup Information AHCI Port0 Port5 While entering setup BIOS auto detects the presence of IDE devices This displays the status of auto detection of IDE devices IS SETUP UTILITY Auto SATA Port0 Port5 Se
36. mode The choice Normal IrDA ASK IR Onboard CIR Port Allows BIOS select Enable or Disable CIR Port The choice Disabled 3E0 2E0 Parallel Port Address This item allows you to configuring I O of the onboard parallel port The choice Disabled 378 278 3BC Parallel Port Mode There are five different modes for the onboard parallel port Switch to Normal mode Bi Directional Switch to Bi Directional mode Switch to ECP mode Switch to EPP mode ECP amp EPP Switch to ECP amp EPP mode Parallel Port IRO Allows BIOS Select Parallel Port IRQ The choice IRQ5 IRQ7 Watch Dog Timer This BIOS testing option is able to reset the system according to the selected table The choice Disabled 30 60 90 120 150 180 210 sec Report Chassis Intrution The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 9 BIOS Setup Information Hardware Health Configuration Configuration monitor the Hardware Health System Temperature 4 CPU Temperature SYSFANZ Speed Ucore ve GFX Ucore E J k LU UBAT ROBO 8719VG2AR User s Manual f Hardware Health Configuration SES SETUP UTILITY 40 C 1904 F 42 107 F 5273 EPN TAFF d P a me Lal nt poo GG GG GG N pa CA Seiect Screen ti Select iten Fi General Hels Fit Save and Exit ESE Exit 4 10 BIOS Setup Information ACPI Configuration Select for Advanced ACPI Configuration
37. n Portwell Inc a world leading innovator in the Industrial PC IPC market and announce a new PICMG 1 0 PCI ISA SBC Single Board Computer ROBO 8719VG2AR which adopts with Intel GM45 and ICH9ME chipset It offers flexible FSB up to 1066MHz selection of Intel amp Core 2 Quad Core 2 Duo Celeron M processors that feature high computing power with lower heat ROBO 8719VG2AR supports multiple displays such as VGA port up to 2048 x 1536 resolution and dual channel 24 bit LVDS port and flexible SDVO connector for other type display via an optional daughter card It can let users have the other kind of choice for display output In addition ROBO 8719VG2AR supports two 240 pin DIMM memory slot for DDR2 SDRAM up to 4GB and comes with dual Gigabit Ethernet ports one parallel port dual COM ports one FDD port three SATA 300 ports RAID 0 1 one Compact Flash socket and Six USB2 0 ports It also equipped with audio codec that supports audio output function via one optional audio card Advanced Management Technology AMT 4 0 is feature that ROBO 8719VG2AR equipped This technology provides remote access capability via Intel Gigabit Ethernet controller The new technology is a hardware based solution that uses out of band communication for system management access to client systems Built in Intel Trusted Platform Module iTPM technology that can enhance platform security ROBO 8719VG2AR brief specifications Support Intel amp C
38. nabled Core Multi Processing Disabled disable one execution core of each CPU die The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 4 BIOS Setup Information Intel amp R SpeedStep tm tech Disabled Enabled GV3 tech function The choice Disabled Enabled IDE Configuration The IDE Configuration the IDE devices such as hard disk drive or CD ROM drive It uses a separate sub menu to configure each hard disk drive Master and Slave Mirrored IDER Configuration i Configure SPIRI as SATAS Configuration Enhanced Bisabled Compatible Exbarced Disabled gt Primary ZP Master f gt Primary ZE Slave Mot detected d gt Secondary IBE Master Met Betectedi I Secondary IDE Slave Mot Betectedi gt Third IDE Master Bot Detected I fourth IDE Master Bet Betectedi f Select Screes f gt Fifth IDE Master Mot Betectedi fi Select item I Fifth IDE Shee Mot Betectedi Le Change Optica i Fi Gemeral Help E Fio Save and Exit d Hard Disk Vrite Protect IBisabledi Exit i IBE Detect Time Gat Sec as STRGTI BOPia Cable Detection ost 8 Pevicei SATA 1 Configuration The choice Disabled Compatible Enabled Configure SATA 1 as This setting specifies the function of the on chip SATA 1 controller The choice IDE RAID AHCI SATA 2 Configuration The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 5 BIOS
39. nd 20 2 Parallel Port Connector 6 Daas 9 Ground Data 6 Busy LH jGround ome poer ROBO 8719VG2AR User s Manual 2 4 Hardware Configuration 3 4P Power Connector for CPU POWER 12V 2 4 m Signal Description Ground 6 17 Serial Port 1 Port 2 Connector 5 TransmitData TXD 6 CleartoSend CTS 7 Data Terminal Ready DTR 8 _ Ring Indicator RI 9 JODA 10 JNC J8 Keyboard amp Mouse Connector 6 HD C8 ae 2 3 PSON ROBO 8719VG2AR User s Manual 2 5 Hardware Configuration 10 Miscellaneous Header Pin2 4 6 Power LED Pin9 11 Power Button Pin13 15 Reset Button Pin14 16 HDD LED 5 Ne LL 6 POWFRIED 7 NCE 8 JNC E 9 POWERBUTTON LINE 12 14 Dual Port USB Header 2 10 OOOOO 1 7 n2 6 USBDP 8 Ground _ O 5 oaw NC 14 Le USBD5P Ground 8 Ground po tN ROBO 8719VG2AR User s Manual 2 6 Hardware Configuration 13 8 Bit GPIO Header PIN No Signal Description PIN No Signal Description SIO GPIO0 SIO GPIO4 SIO GPIO1 SIO GPIO5 5 SO GPIO 6 SIOGPIOG 7 soro 8 9 Ground tS 15 J16 USB Port 1 2 ee O a 3 USBDIN LA LUSBDIN O 5 USBDIP SBOP 7 8 Ground 17 23 RJ45 LAN Por
40. onfiguration 11 Ground 12 Ground 5V ETA tas ss 33 Grund LA J34 Case Open Detection PIN No CASEOPEN ATX1 Power Head LH PIN No ROBO 8719VG2AR User s Manual 2 11 System Installation Chapter 3 System Installation This chapter provides you with instructions to set up your system The additional information is enclosed to help you set up onboard PCI device and handle Watch Dog Timer WDT and operation of GPIO in software programming 3 1 Intel amp mPGA 478MN CPU Installing Intel mPGA478MN CPU 1 Lift the handling lever of CPU socket outwards and upwards to the other end 2 Align the processor pins with pinholes on the socket Make sure that the notched corner or dot mark pin 1 of the CPU corresponds to the socket s bevel end Then press the CPU gently until it fits into place If this operation is not easy or smooth don t do it forcibly You need to check and rebuild the CPU pin uniformly ROBO 8719VG2AR User s Manual 3 1 System Installation 3 Push down the lever to lock processor chip into the socket once CPU fits mPGA 478MN Socket Close 2 OPEN 3 Follow the installation guide of cooling fan or heat sink to mount it on CPU surface and lock it on the mPGA478MN socket Removing CPU 1 Unlock the cooling fan first 2 Lift the lever of CPU socket outwards and upwards to the other end 3 Carefully lifts up the existing CPU to rem
41. ore 2 Quad Core 2 Duo Celeron M processors in mFCPGA package with FSB 1066 800 667MHz Two 240 pin DDR2 SDRAM DIMM socket support for DDR2 800 667 DIMMs up to 4GB system memory Intel GM45 integrated GMA 4500MHD that support DirectX 10 OpenGL 2 0 MPEG 2 hardware acceleration Equipped dual Gigabit Ethernet port Support one Compact Flash socket two COM ports thee SATA ports and Six USB 2 0 ports dual ports on bracket ROBO 8719VG2AR User s Manual 1 1 System Overview 1 2 Check List The ROBO 8719VG2AR package should cover the following basic items Se fa ZS Se NN SN One ROBO 8719VG2AR single board computer One COM port cable with bracket One 4 pin ATX power control cable for backplane connection One Parallel port cable One SATA cable One FDD cable One active CPU cooler One Installation Resources CD Title If any of these items is damaged or missing please contact your vendor and keep all packing materials for future replacement and maintenance 1 3 Product Specification Main processor Support Intel Core 2 Quad Core 2 Duo Celeron M processors CPU bus clock 1066 800 667 MHz Chipset Intel GM45 and ICH9ME Main Memory Support dual channel DDR2 memory interface Up to 4GB DDR2 SDRAM on two 240 pin DIMM socket Bus Interface Follow PICMG 1 0 Rev 2 0 standard 32 bit PCI and 16 bit ISA Fully complies with PCI Local Bus specification V2 2 support 4 master PCI slots Suppor
42. ort Please find Ethernet combination driver for operating Intel amp 82567LM and 82574L Gigabit LAN form ROBO 8719 CD title The drivers support Windows 2000 XP System 32 Bit amp Windows XP System 64 bit Windows 2000 XP 32bit Please execute Install for Windows 2000 XP System 32 Bit file to start Intel amp LAN driver installation Windows XP 64 bit Please execute Install for Windows XP System 64 bit file to Ethernet Intel Intel _Gigabit_64bit Pass below button into the dictionary ROBO 8719VG2AR User s Manual 3 4 System Installation LED Indicator for LAN status ROBO 8719 provides three LED indicators to report Intel 82567LM and 82574L Gigabit Ethernet interfaces status Please refer to the table below as a quick reference guide Operation of Ethemet P 82566DM Color Name of LED perakton o SE Yellow LAN Linked amp Active LED Speed LAN speed LED LED Orange Green Off 3 3 4 On board AC 97 Audio Device Please find Realtek ALC262 Audio driver of ROBO 8719 CD title The drivers support Windows 2000 XP Server 2003 3 3 5 Intel amp Matrix Storage Manager Device Drivers Support Please find utility tool for Intel amp ICH9ME of ROBO 8719 CD title The drivers support Windows 2000 XP System 32 Bit amp Windows XP System 64 bit Installing Serial ATA hard disks The ROBO 8719 supports Three Serial ATA hard disk drives For optimal performance install identical drives of the s
43. ou have in the box and give you an overview of the product specifications and basic system architecture for this series model of single host board Chapter 2 Hardware Configuration Shows the definitions and locations of Jumpers and Connectors that you can easily configure your system Chapter 3 System Installation Describes how to properly mount the CPU main memory and Compact Flash to get a safe installation and provides a programming guide of Watch Dog Timer function Chapter 4 BIOS Setup Information Specifies the meaning of each setup parameters how to get advanced BIOS performance and update new BIOS In addition POST checkpoint list will give users some guidelines of trouble shooting Chapter 5 Troubleshooting Provides various useful tips to quickly get its running with success As basic hardware installation has been addressed in Chapter 3 this chapter will basically focus on system integration issues in terms of backplane setup BIOS setting and OS diagnostics The content of this manual is subject to change without prior notice These changes will be incorporated in new editions of the document Portwell may make supplement or change in the products described in this document at any time Updates to this manual technical clarification and answers to frequently asked questions wil be shown on the following web site http www portwell com tw System Overview Chapter 1 System Overview 1 1 Introductio
44. ove it from the socket 4 Follow the steps of installing a CPU to change to another one or place handling bar to close the opened socket CPU Application Supports Intel Core 2 Duo 45nm Celeron M 45nm Penryn processor in a 478MN socket equipped with dual core Hyper Threading EM64T EIST and XD amp VT technologies 3 2 Main Memory ROBO 8719 provides 2 x 240 pin DDR2 SDRAM DIMM sockets support 1 8V dual channel DDR2 800 667 non ECC DIMMs The maximum memory size can be up to 4GB Auto detecting memory clock is according to BIOS CMOS settings For system compatibility and stability don t use memory module without brand You can also use single sided or double sided DIMM in both slots Watch out the contact and lock integrity of memory module with socket it will impact on the system reliability Follow normal procedures to install your DRAM module into memory socket Before locking make sure that all modules have been fully inserted into the card slots ROBO 8719VG2AR User s Manual 3 2 System Installation PS When EE insert a Ge Sg we es to insert in DIMM 0 J11 T 000 Go N 9000009000000000000000000000 nm ue Y Y ec oe vno nr rv M Dual Channel DDR2 DIMMs Dual Channel DDR2 memory technology doubles the bandwidth of memory bus Adequate or higher bandwidth of memory than processor would incr
45. re are total four connectors J18 J19 J21 The installation of Serial ATA is simpler and easier than IDE because SATA hard disk doesn t require setting up Master and Slave which can reduce mistake of hardware installation All you need to do is to plug in two cables and enable SATA in System BIOS Hard Drive Serial ATA Power Cable Serial ATA Data Cable ROBO 8719VG2AR User s Manual 5 1 Troubleshooting 5 2 BIOS Setting It is assumed that users have correctly adopted modules and connected all the devices cables required before turning on ATX power CPU CPU Fan 240 pin DDR2 SDRAM keyboard mouse floppy drive IDE hard disk printer VGA connector device cables ATX accessories or 12V 4 pin power cable are good examples that deserve attention With no assurance of properly and correctly accommodating these modules and devices it is very possible to encounter system failures that result in malfunction of any device To make sure that you have a successful start with ROBO 8719 series it is recommended when going with the boot up sequence to hit DEL key and enter the BIOS setup menu to tune up a stable BIOS configuration so that you can wake up your system far well Loading the default optimal setting When prompted with the main setup menu please scroll down to Load Optimal Defaults press Enter and Y to load in default optimal BIOS setup This will force your BIOS setting back to the initial factory configura
46. rt 1 of Superio2 is ooooiiii o output iinput Set CFG2 0xF2 0x00 GPIO Port 1 of Superio2 is non inversed Set CFG2 0x07 0x07 Select logic device 07 Set CFG2 0xF1 OxFF Initial back all GPIO Port1 of Superio 2 to hi Set CFG2 0x07 0x07 Select logic device 07 Set CFG2 0xF1 OxEF GP14 of Superio2 gt GP10 of Superio2 Set CFG2 0x07 0x07 Select logic device 07 of Superio2 02 Get_CFG2 0xF1 get GPIO Port 2 data if d2 OxEE printf n GPIO14 gt 10 test ok else printf n GPIO14 gt 10 test fail ROBO 8719VG2AR User s Manual 3 12 BIOS Setup Information Chapter 4 BIOS Setup Information ROBO 8719VG2AR is equipped with the AMI BIOS stored in Flash ROM These BIOS has a built in Setup program that allows users to modify the basic system configuration easily This type of information is stored in CMOS RAM so that it is retained during power off periods When system is turned on ROBO 8719VG2AR communicates with peripheral devices and checks its hardware resources against the configuration information stored in the CMOS memory If any error is detected or the CMOS parameters need to be initially defined the diagnostic program will prompt the user to enter the SETUP program Some errors are significant enough to abort the start up 4 1 Entering Setup Launch System Setup Power on the computer and the system will start POST Power On Self Test process When th
47. t 1 2 6 GND GND 8 UMDNn 8 J DMDN 9 umor 9 LMDID ROBO 8719VG2AR User s Manual 2 7 Hardware Configuration J18 J21 J22 SATA Interface Connector PIN No Signal Description SATA TXP4 SATA TXP1 SATA TXNO SATA TXNA4 SATA TXN1 J19 J20 J30 3P FAN Power Connector 123 HOO 25 LVDS Panel Connector 3 EVDSADATA 6 LVDSA_DATA2 7 LVDSA DATAS Lg LVDSADATA 9 LVDSACLK 10 LVDSACLK ROBO 8719VG2AR User s Manual 2 8 Hardware Configuration 26 Audio Header PIN No Signal Description 1 2 CN G 3 G G CN G ESTA 2 A 6 7 CN_LINOUT L Pp 8 9 4 27 D SUB15 VGA Connector 5 Ground Ground _ _______ 7 Grud 8 Ground _ _______ 2 NC 91 15 DDCCLK yj J28 SDVO Board To Board Connector 5 DUAL 7 yea LB 9 LN 10 we ROBO 8719VG2AR User s Manual 2 9 Hardware Configuration 21 GND 22 SDVO TVCLKIN 26 GND i e Signal Description Backlight Power select by JP9 Ground 32 Compact Flash Socket PIN No Signal Description PIN No Signal Description 1 Leed 2 Dan 3 Dua at 5 bua 6 Dayo 7 spem 8 Gemd 9 Gemd 19 Gemd 4 1 9 5 7 ROBO 8719VG2AR User s Manual 2 10 Hardware C
48. t ISA function via Winbond PCI to ISA bridge W83628AG and W83629AG System BIOS AMI BIOS Floppy Drive Interface Support one FDD port up to two floppy drives and 5 1 4 360K 1 2MB 3 1 2 720K 1 2MB 1 44MB 2 88MB diskette format and 3 mode FDD Parallel Port Support one parallel port with SPP EPP and ECP modes SATA Interface Three SATA ports support RAID 0 1 ROBO 8719VG2AR User s Manual 1 2 System Overview Serial Ports Support two serial ports one is RS232 the other is RS232 422 485 selectable ATX Power Control Interface One 4 pin header to support ATX power control via backplane USB Interface Support six USB Universal Serial Bus ports Dual USB ports on bracket Audio Interface On board Audio codec via HD Audio interface One optional Audio kit PA M1AU for Mic in Line in Line out Auxiliary I O Interfaces System reset switch external speaker and HDD active LED etc Real Time Clock Calendar RTC Support Y2K Real Time Clock Calendar with battery backup for 7 year data retention Watchdog Timer Support WDT function through software programming for enable disable and interval setting Generate system reset On board VGA Intel amp GMCH Integrated 4500MHD Graphics device Intel DVMT 5 0 supports up to 128MB video memory On board Ethernet LAN Intel 82567LM and 82574L Gigabit Ethernet controller to support two RJ 45 connector on I O bracket High Driving G
49. the onboard USB 2 0 controller The choice FullSpeed HiSpeed BIOS EHCI Hand Off This is a workaround for OSes without EHCI hand off support The EHCI ownership change should claim by EHCI driver The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 24 BIOS Setup Information 44 PCIPnP Advanced PCI PnP setting wrong values in below sections may cause system to malfunction WARMING Setting wrong valees in below sections may cause system to malfunction Pieg Flay US f PCI Lateecy Timer D i f Allocate IRG to PCi UGA ROBO 8719VG2AR User s Manual 4 25 BIOS Setup Information BIOS SETUP UTILITY Available Ifwailablel Available Available Available Ifvailablel ied Memory Size Clear NVRAM Clear NVRAM during System Boot The choice No Yes Plug amp Play O S No lets the BIOS configure all the devices in the system Yes lets the operating system configure Plug and Play PnP devices not required for boot if your system has a Plug and Play operating system The choice No Yes PCI Latency Timer Select value in units of PCI clocks for PCI device latency timer register The choice 32 64 96 128 160 192 224 248 Allocate IRQ to PCI VGA Yes Assigns IRQ to PCI VGA card if card requests an IRQ No Does not assign IRQ to PCI VGA card even if card requests an IRQ The choice No Yes ROBO 8719VG2AR User s Manual 4 26 BIOS Setup Information
50. tion It is recommended to do this so you can be sure the system is running with the BIOS setting that Portwell has highly endorsed As a matter of fact users can load the default BIOS setting any time when system appears to be unstable in boot up sequence Auto Detect Hard Disks In the BIOS gt Standard CMOS setup menu pick up any one from Primary Secondary Master Slave IDE ports and press Enter Setup the selected IDE port and its access mode to Auto This will force system to automatically pick up the IDE devices that are being connected each time system boots up Improper disable operation There are too many occasions where users disable a certain device feature in one application through BIOS setting These variables may not be set back to the original values when needed These devices features will certainly fail to be detected When the above conditions happen it is strongly recommended to check the BIOS settings Make sure certain items are set as they should be These include the floppy drive COM1 COM2 ports Parallel port USB ports external cache on board VGA and Ethernet It is also very common that users would like to disable a certain device port to release IRQ resource A few good examples are ROBO 8719VG2AR User s Manual 5 2 Troubleshooting Disable COMI serial port to release IRQ 4 Disable COM2 serial port to release IRQ 3 Disable Parallel port to release IRO 7 Disable PS 2 mouse to release IRQ 12 Etc
51. to use the display mode of optional ROM The choice Force BIOS Keep Current Bootup Num Lock This setting is to set the Num Lock status when the system is powered on Setting to On will turn on the Num Lock key when the system is powered on Setting to Off will allow users to use the arrow keys on the numeric keypad The choice Off On PS 2 Mouse support Select Enabled if you need to use a PS 2 interfaced mouse in the operating system The choice Disabled Enabled Auto Wait For EU If Error When this setting is set to Enabled and the boot sequence encounters an error it asks you to press F1 If disabled the system continues to boot without waiting for you to press any keys The choice Disabled Enabled Hit DEL Message Display Set this option to Disabled to prevent the message as follows Hit Del if you want to run setup It will prevent the message from appearing on the first BIOS screen when the computer boots Set it to Enabled when you want to run the BIOS Setup Utility The choice Disabled Enabled Interrupt 19 Capture Interrupt 19 is the software interrupt that handles the boot disk function When enabled this BIOS feature allows the ROM BIOS of these host adaptors to capture Interrupt 19 during the boot process so that drives attached to these adaptors can function as bootable disks In addition it allows you to gain access to the host adaptor s ROM setup utility if one is available R
52. ty Cycle in Throttle mode The choice 87 5 75 0 62 5 5076 37 5 2576 12 576 Keyboard amp PS 2 Mouse The choice IGNORE MONITOR Power Button Mode Go into On Off or Suspend when Power button is pressed The choice On Off Suspend Resume On Ring Disable Enable RI to generate a wake event The choice Disabled Enabled Resume On PCIE WAKE Disable Enable GPI to generate a wake event The choice Disabled Enabled Resume On PCI PME Disable Enable PME to generate a wake event The choice Disabled Enabled Resume On RTC Alarm Disable Enable RTC to generate a wake event The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 18 BIOS Setup Information Intel AMT Configuration Select for Intel amp AMT Configuration BIDS SETUP UTILITT Intel AMT Support Disable Enable Intel AMT function support The choice Disabled Enabled If you want to use AMT function LAN cable must on 82567LM Force IDER The choice Disabled IDER Pri Master IDER Pri Slave IDER Sec Master IDER Sec Slave Force SOL The choice Disabled Enabled ROBO 8719VG2AR User s Manual 4 19 BIOS Setup Information MPS Configuration Configure the Multi Processor Table BIDS SETUP UTILITY MPS Revision This field allows you to select which MPS Multi Processor Specification version to be used for the operating system You need to select the MPS version supported by your operatin

ROBO-8719VG2AR User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents