TPMS-222 Owner`s Manual
Contents
1. Transmitter Failure Warning lf the receiver does not receive a valid transmission from a specific sensor transmitter for more than 20 minutes the system will assume a problem with the transmitter and display The location icon will light to indicate which transmitter has a problem Sensor Transmitter failure warning for left front tyre sensor _ Si H Receiver Failure Warning If the display does not receive any transmission from any sensor transmitter for more than 3 minutes the display will indicate a receiver failure warning and show Err la r Receiver Failure Warning ATTENTION 4 In the event of any of the above system failure error messages we strongly recommend you take your vehicle to the nearest dealer as soon as possible to have the problem identified and rectified Under these conditions the system will no longer be able to monitor one or all of the tyres Document 920 9001 Rev A 4 March 2012 Page 7 I Multiple problem detection on one Tyre If both pressure and temperature warning are triggered on the same tyre the system will indicate the problem as follows gt VV V WV The digits displaying the tyre pressure and temperature will flash The icon indicating the tyre with the problem will illuminate The icon indicating a rapid leak will illuminate The abnormal tyre condition icon will illuminate The system will emit warning beeps High pressure warning high temperature warning2. Range Standard Working Voltage Voltage Range Power Component i Vmax Supply Transmitter 3v 3 6v Lithium battery Document 920 9001 Rev A 4 March 2012 Page 11 9 Warranty The warranty provided with the product covers substantial manufacturer s defects in workmanship and materials It does not cover any unit that is damaged beyond normal usage was not properly installed was subject to chemical contact or other acts not sanctioned by this User Manual All components are covered for one 1 year and unlimited mileage following the date of installation The warranty will be honoured by any authorised Inawise Dealer The owner is required to provide dated proof of the purchase The authorised dealer will determine if there is a warrantable condition associated with materials and or manufacturing workmanship If a warrantable condition exists the component will be replaced free of charge and shipping prepaid The owner is responsible for all labor and installation charges The warranty does not include any further obligation whatsoever including but not limited to actual installation of the replacement unit on the customer s vehicle All other Warranties express or implied are disclaimed All collateral agreements which purport to modify this limited warranty are of no effect The absolute limit of liability is the purchase price of the unit Inawise Pty Ltd or the manufacturer Shanghai Baolong Automotive Corporation is not liabl
3. The icon indicating the tyre with the problem will illuminate gt The abnormal tyre condition icon will illuminate gt The system will emit warning beeps The high temperature warning mode will remain active until the problem is corrected High temperature warning for the left front tyre ATTENTION 4 When the system indicates a high tyre temperature warning do not try cool the tyre with cold water Pull over and allow the tyre to cool down slowly Excessive high temperature can cause a tyre blowout so pull over as soon as it safe to do so and allow the tyre to cool down E Rapid Leakage Warning When a tyre starts to deflate quickly the system will detect the rapid pressure drop and trigger a fast leakage warning gt The digits displaying the tyre pressure will flash gt The icon indicating the tyre with the problem will illuminate gt The icon indicating a rapid leak will illuminate gt The system will emit warning beeps Rapid leakage warning for the left front tyre Document 920 9001 Rev A 4 March 2012 Page 6 F No ID Module Warning The ID modules installed in the main unit are used to record and identify the ID code of the transmitters When receiving data from the transmitters the receiver will carry out a self check If a problem is detected with one of the ID module the system will display a warning Please see to the following image IE No ID module warning for the left front tyre G
4. All tyres are continuously monitored whether the vehicle is stopped or moving or whether the accessories power is turned on or off Audible and visual alarms are given only when the accessory power is on and when an abnormal tyre condition is detected by the system As the system monitors the tyres even when the vehicle is moving the driver is notified of a problem as it occurs providing the driver with a real time notification of a potential danger Each tyre has a monitoring module sensor transmitter installed inside the rim to monitor pressure and temperature in real time This data is sent to the receiver wirelessly via a Radio Frequency RF transmission and displayed on the display The system will provide warnings about abnormal tyre conditions such as air leakages low pressure high pressure and high temperatures Sensor Transmitter module apeg ATTENTION A This TPMS product is a proactive safety system It cannot eliminate all possibilities of tyre related accident or prevent such accidents from happening What the system can do is advise the driver of an abnormal tyre conditions enabling the driver to address the problem before the condition of the tyre reaches an unsafe level lt is imperative that when an alert is given that the driver addresses the problem by pulling over as soon as it is safe to do so and ascertain the cause of the alert Document 920 9001 Rev A 4 March 2012 Page 3 4 Key Fun
5. TPMS 222 Owner s Manual Document 920 9001 Revision A 4 March 2012 Inawise Pty Lid 1 Table of Contents mee 16 or 0 G0 E en enter rire rere ere reer re ere ree ee 2 A A A R E E ee a 2 s Pe Or Oe O a A A A A RR 3 4 Key Functions and Operation so c sssrsscasstecasecetssectea sacesnusascateessacatensieueqeassedassasenessetenateendeestentdnaedsdnmnsatanstasedmncsnastouante 4 4 1 BZ lay AO BETS 4 4 2 OPELA OC pa E AA E OOPS 4 P NOn C ONAIE esea6104448104046403640664616400600364060400400600362060400400600364060460200600361060460200600361050 0006669060 GOES GOG C 4 BD PAPO ess US Wairini woo R AGOR AERO ORA AO ACO 5 OF hes Ge VY ARMIN a 5 DET ate erae A EE 6 PERT TG alate Vy AGMA nE E A 6 ENOM oue Wy A a E E EE AAA E REEE SELE EEES NE EEEE E E E 7 G Iransmitter Paire WIEN ennan na E GA OC 7 PE IRGCCE ror Fable Wy ANIO A A AAA E E E E E 7 I M liple problem detec on on one DEE occhi Oo Eo ZGAGA aaa ona a aana 8 T FS iy Sy E easier kd E 8 3 REPACING SENSO Transmite CNN E 9 i BR i apie tec i za Ozeo io O io 9 COS NE OUI SOON E E EA ENNY 10 Oe PC CIPO AON nun EE E E Paseo a co Poe twa wadzi 11 Dice WY ODRANO cantceed onsacesauenocesdccsecnsconetenecoasececceusee es 4aaneceacoanecneceasegeudaasecescaanecessucpoces lt eesecasaaceecnac OO SAECO OCS Zd 12 10 DAC VV IMI pak E E EOE A R AAAA E 12 2 General e The TPMS 222 are wireless TPMS Tyre Pressure Monitoring Systems specifically designed for In Dash moun
6. and quick leakage warning appear at same time for the left front tyre J Multiple tyre warning In the event that multiple tyres are detected with a problem the system will rotate the display data from one tyre to the next The RD button can be used to manually scroll the display to the next faulty tyre The display will continue to display the warnings until all fault conditions are corrected Document 920 9001 Rev A 4 March 2012 Page 8 5 Replacing Sensor Transmitters lf the sensor transmitter or ID module become faulty both need to be replaced as they are a matched set First replace the faulty sensor transmitter located inside the rim with a new one and then replace the ID module supplied with the new sensor transmitter The ID module plugs into the receiver module assembly mounted behind the dash Start your vehicle and drive it for a few minutes to activate the sensor transmitter from its shipping sleep mode Encapsulated electronics housing containing processor sensor RF transmitter and lithium battery Valve Stem with ID letter A Sensor transmitter module assembly 6 Tyre Rotation When tyres are rotated on the vehicle the sensor ID modules also need to be rotated in order to update the system with the new tyre and hence sensor transmitter locations The ID modules are located inside the receiver module First turn the Acc power off by turning the ignition key to the off position Remo
7. ctions and Operation 4 1 Display Interface RD function button A Under normal operating tyre conditions the display circulates every 3 seconds displaying the data for each individual tyre By pressing the RD button the display will toggle over to the next tyre enabling the user to scroll to the readings for a particular tyre quickly B When the system detects a problem and sounds an alert pressing the RD button turns off the audible alert If the problem is not rectified within 20 minutes the alert will sound again Turning the accessory power to the unit off and on again will reset the alert beeper 4 2 Operating modes A Normal Condition Under normal tyre conditions the tyre pressure and temperature for each tyre is displayed in a 3 second rotational sequence The icons at the 4 corners of the display reflect the particular tyre whose data is being displayed When the system is first installed and setup the display will show indicating no data has been received from the tyre sensor transmitter as yet Document 920 9001 RevA 4 March 2012 Page 4 B High Pressure Warning When the pressure of a tyre becomes greater than 46 6psi a high pressure warning will be triggered gt The digits displaying the tyre pressure will flash gt The icon indicating the tyre with the problem will illuminate gt The abnormal tyre condition icon will illuminate gt The system will emit warning beeps Th
8. e for any direct consequential indirect or punitive damages of any kind 10 Safety Warning This product is designed to monitor vehicle tyre pressures and temperatures it is not designed to provide warnings of sudden catastrophic tyre failure blowouts caused by external influences The driver should always react promptly to warnings The driver should not assume that because the TPMS system has not reported any problems that no problems with the tyres or the vehicle exist This product is a proactive safety system It cannot eliminate accidents caused by tyre failure but it does give alert to drivers about abnormal and possibly dangerous tyre conditions Whenever the system alerts to a problem pull the vehicle over as soon as it is safe to do so and ascertain the cause of the alert Depending on the type of tyres fitted to your vehicle in many cases low tyre pressure cannot be determined by simply visually inspecting the tyre If the system alerts to a low tyre pressure in all probability it is because the tyre pressure is dangerously low even though the tyre may look fine Tyres can fail for other reasons besides low pressure overheating or overloading Always be on the alert for other tyre related problems indicated by unusual noises vibrations uneven tread wear or bulges on the tyre If any of these signs are detected have the tyres checked immediately by a professional Disclaimer While every attempt has been made to ensure a
9. e high pressure warning mode will remain active until the problem is corrected High pressure warning for the left front tyre ATTENTION A Excessive high tyre pressure is a dangerous condition which can lead to sudden depressurisation of the tyre normally referred to as a BLOWOUT When this happens control of the vehicle will be impaired including the ability of the vehicle to steer and brake creating a potentially catastrophic condition As such it is imperative that any vehicle should not be driven with excessively over inflated tyres If the system detects this condition the driver should pull over as soon as it is safe to do so and rectify the problem usually by letting some of the air out of the tyre C Low Pressure Warning When the pressure of a tyre drops below 23 2psi a low pressure warning will be triggered gt The digits displaying the tyre pressure will flash gt The icon indicating the tyre with the problem will illuminate gt The abnormal tyre condition icon will illuminate gt The system will emit warning beeps The Low pressure warning mode will remain active until the problem is corrected Ps yir M Low pressure warning 2 a for the left front tyre C O Document 920 9001 Rev A 4 March 2012 Page 5 D High Temperature Warning When the temperature of a tyre rises higher than 80 C a high temperature warning will be triggered gt The digits displaying the temperature will flash gt
10. ll information in this manual is accurate Inawise Pty Ltd or any of its associated companies or subsidiaries will not be held liable in any way what so ever for any errors or omissions which may be present in this document Inawise follows a policy of continuous improvement Specifications may change at any time without notice This product is to be used only for the purpose described in this manual Document 920 9001 Rev A 4 March 2012 Page 12
11. s exceeding 70 C 158 F for a period exceeding 1 hour ATTENTION A When the system is powered up for the very first time the display will show while it is waiting for the first reception from the transmitters The sensor transmitters are shipped in a sleep mode in order to ensure maximum battery life The sensor transmitters only activate out of this shipping sleep mode when they are put into a pressurised environment and subject to mechanical movement as would be the case when they are fitted to the rim of a vehicle and then rotated Document 920 9001 Rev A 4 March 2012 Page 10 8 Specifications Models TPMS 222 Pressure displayed in PSI pounds per square inch and temperature in C Celsius Sensor Weight 36g 1 26 oz Dimensions 1 5x2 8x6 4 0 59x2 50x1 11 inch Pressure Monitoring Range OPsi 51Psi Operating Temperature Range 40 C to 125 C Temperature Monitoring Range 40 C to 99 C Operating Humidity Range 45 98 Pressure Accuracy 0 73 PSI at 0 C 50 C Temperature Accuracy 2 C Battery Life 5years at 20 hours driving per day Frequency 433 92MHz Display Power Consumption 130 mW Regular 230mW Max Power Supply DC 12 Volt Nominal Operating Temperature Range 20 C to 70 C Operating Humidity Range 45 75 Pressure Resolution 0 2PSl Temperature Resolution 1 C Receiver Operating Temperature Range 20 C to 70 C Operating Humidity Range 45 75 Working Voltage
12. ting e Thank you for purchasing a genuine Inawise product e Please read and follow the installation guide carefully in order to get the most out of the product and to ensure reliable and dependable operation This product should not be used for any other purpose or use or installed in any other way other than that described in this manual and the installation manual In order to get the most of what this product has to offer please read this manual thoroughly and ensure you understand how this product works the benefits it provides and the limitations it has Running your vehicle with the correct tyre pressure will not only improve the handling of the vehicle but will reduce petrol consumption and significantly reduce tyre wear While this product alerts the driver when a tyre condition has reached a dangerous level the product can also be used to quickly and easily check the tyre pressures enabling to driver to monitor these pressures and then adjust them to an optimum level at regular intervals A Throughout this manual you will see the following symbol The symbol denotes guidelines that must be followed to ensure the safety of your vehicle is not compromised ATTENTION Document 920 9001 Rev A 4 March 2012 Page 2 3 Principles of Operation After turning the vehicle Accessories power on by turning the vehicle ignition switch the display will illuminate and display the pressure and temperatures of the vehicles tyres
13. ve the plastic cover on the receiver module enclosure to expose the ID module Next simply unplug the modules and plug them into the new location corresponding to the location of the tyre Each ID module is labelled A B C and D The corresponding sensor transmitter has the same marking on the valve stem body Document 920 9001 Rev A 4 March 2012 Page 9 7 Trouble Shootings ID module is not properly connected with Turn ACC power off Pull out the ID Display shows when The transmitter has failed Please Display shows when External RF signal is blocking the signal Turn off or disable the offending The display does not Check the power wire connections 1 Improper connection of power wire Check the power wire connections 2 The temperature in the vehicle is over Avoid parking the vehicle under strong Display is blank STW during very hot days Display does not update System failure Restart the Restartthe system OO The display shows incomprehensible codes System failure Restart the system 1 Occasionally when parked the system may display on the screen when the vehicle is first started This might be caused by surrounding RF interference This is not a fault condition the display will update as soon as you move the vehicle away from the RF interference source 2 Do not park the vehicle under strong sunlight The LCD screen may suffer permanent damage if exposed to temperature
Download Pdf Manuals
Related Search