Home

TASI Safety Manual (June 04, 2013) - Tri

Contents

1. All accidents will be investigated by an RME appointed by Corporate Investigations may or may not include the following Onsite review with any employee located on the job site where the accident occurred Individual question regarding the accident Drug amp Alcohol testing of any employee performing any work on the job site where the accident occurred Telephone interview with any employee performing any work on the job site where the accident occurred Reenactment of the accident onsite or off site with any employee performing any work on the job site where the accident occurred The purpose of completing an accident investigation is to document as many details of the accident as soon as possible to insure as much clarity as possible to aid in the investigation process Accident reports highlight problem areas Through the use of good reports accident patterns can be detected and resources directed toward prevention Accident reports make excellent training tools The cause and effect of accidents can be reviewed at safety meetings Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 EMERGENCY PROCEDURES IN THE EVENT OF AN ACCIDENT IF an accident does occur and emergency services are needed do the following If you are working in a facility where emergency services are provided follow their procedures for reporting accidents incidents and then contact your direct supervisor for immediate follow up If y
2. The requirement of chemical manufacturers and employers to communicate information to workers about the hazards of workplace chemicals or products including training HAZCOM Known as the Right to Know Law is the legal principal that the individual has the right to know the chemicals to which they may be exposed to in their daily employment while working for any employer or any job Exposed Exposure An employee is subjected to hazardous chemical s in the course of employment through any route of entry inhalation ingestion skin contact or absorption and includes potential accidental or possible exposure s Communication The imparting or interchange of thoughts opinions or information by speech writing to portray information It is Tri State s responsibility to prepare and implement a Hazard Communication HAZCOM program for all employees This includes communicating the potential hazards you may come in contact with on any jobsite you are asked to work on does not include other trades information and how to address them should you or your fellow workers come in contact with them How to address exposures is completed through the use of MSDS sheets provided to you through the employee portal located www tri statesprinkler com It is every employee s responsibility to know their rights in accordance with HAZCOM The Right to Know Law be able to identify potential hazards in the work pla
3. Management has the authority to procure the necessary resources to execute the objectives of our company s safety and health program We will hold managers supervisors and employees accountable for meeting their responsibilities so that essential tasks will be performed It is Tri State s objective to insure a safe and productive working environment for all employees working on all jobsites and to insure that you and your family are able to benefit from employment here at Tri State To be successful such a policy must embody the proper attitude toward injury and illness prevention and awareness on the part of management supervisors and employees alike Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 CORPORATE RESPONSIBILITIES 1 Eliminate potential hazards by providing appropriate safeguards personal protective equipment and safe work tasks 2 Provide necessary personal protective equipment 3 Provide effective training which is required by the standards as a minimum for all employees 4 Become familiar and comply with applicable OSHA standards 29 CFR 1910 General Industry and 1926 Construction and make copies of all safety and health programs available for employees to review 5 Review consider for approval and execute appropriate action on safety policies developed or suggested by any employee 6 Ensure a high level of productivity and safety performance Tri State Automatic Sprinkler Inc SM 20
4. ask your foreman When lifting use the approved lifting technique i e bend your knees grasp load firmly keep load close to you and then raise the load keeping your back as straight as possible Always get help with heavy or awkward loads Do not engage in horseplay avoid distracting others be courteous to fellow workers Always use the right tools and equipment for the job Use them safely and only when authorized If you are not familiar with the safe way to use a particular tool or piece of equipment ask your supervisor When using your own tools on the job site make sure all guards ground pins etc are in place Good housekeeping must always be practiced Return all tools equipment materials etc to their proper places when you are finished with them Keep floors clean and passageways clear Poor housekeeping wastes time energy and material and often results in injury The use of drugs and or intoxicating beverages on the jobsite is forbidden Being under the influence of alcohol or drugs when on the jobsite is inexcusable Immediate discharge for being under the influence and or using drugs or alcohol may be instituted Additional appropriate disciplinary action will be taken for the following offenses Fighting no matter what the cause Insubordinate conduct or refusal to follow directions False statement such as injury claims Other inappropriate behavior including but not limited to failure to obey safety
5. and where to go in the event of an emergency Stay alert for potential severe weather conditions and what to do in the event of such an occurrence Insure that your first aid kit is fully stocked as it was issued to you and that you know where it is available for emergencies If the jobsite you are working on has emergency reporting procedures know them so that you do not waste time when reporting your situation location Be prepared to tell them your exact location including building name number or room number your name and phone number you are calling from and the details of the emergency If your jobsite does not have specific emergency reporting procedures call 911 and be ready to give them the same information as outlined above Familiarize yourself with the signs of someone needing first aid Bleeding dizziness extreme fatigue skin discoloration swelling disorientation rapid breathing shallow breathing faint voice vomiting nausea agitation burns eye injuries nose bleeding electric shock restlessness and confusion are just a few signs that can be displayed If you or your fellow worker is ever displaying any of these signs take the proper precautions Stop work report injuries emergencies in the proper manner insure that there is no way for the situation to continue and get help Sometimes it is the speed of response and little things that you do to help someone who is displaying any signs of needing basic fir
6. energized and grounded by a qualified electrician before any work can commence Working over any existing overhead power line is ever allowed for any reason e When completing any task for any reason on or near energized or de energized equipment all unqualified personnel must maintain a minimum of a 10 clearance from the energized de energized equipment e Any vehicle or mechanical equipment capable of having parts of its structure elevated near energized overhead lines shall be operated so that a clearance of 10 ft 305 cm is Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 maintained If the voltage is higher than 50kV the clearance shall be increased 4 in 10 cm for every 10kV over that voltage e Employees may not enter any work site containing exposed energized parts unless adequate illumination is present No state workers may enter these sites either e Protective shields protective barriers or insulating materials as necessary shall be used when working in confined or enclosed work spaces where electrical hazards may exist e All portable ladders must have nonconductive rails NO ALL METAL LADDERS ARE ALLOWED ON ANY PROJECT SITE e Conductive apparel shall not be worn unless the items are rendered non conductive by covering wrapping or other insulating means Plan out your work and de energize equipment you are working above or around when possible The approach to complete the work at hand must be discussed and
7. forth regarding these tasks Assigned fire watchers must be trained in the use of fire extinguishing equipment and familiar with the facilities for sounding an alarm in the event of a fire If the object being welded or cut cannot be moved to a more suitable location to complete the task all combustible materials must be relocated during the task or be protected from the task being performed If all the fire hazards cannot be removed then guards shall be used to confine the heat sparks and slag and to protect the immovable fire hazards If the site you are working on requires a hot work permit to be completed they must be completed before any work can commence in strict accordance with the site specific requirements When evolution of hazardous fumes gases or dust is possible any welding cutting or burning of lead base metals zinc cadmium mercury beryllium or exotic metals or paints not listed here shall have proper ventilation or respiratory protection Operators must report any equipment defect or safety hazards that they discover and discontinue use of equipment until all hazards have been repaired or replaced If any welding or cutting cannot be performed in a safe manner then no work shall commence until suitable arrangements have been made to remove all fire hazards or the item work is to be completed on is moved to a safe area for the work to be completed A fire watch is required when welding cutting brazing and or solde
8. maintained by a RME assigned and trained as required by all AHJ offices Individual employee records are available for review at any time Notify your direct supervisor as to your need to review your recor ds The review of individual documentation does not give anyone the right to alter any documents for any reason The following is a list of documents that may be maintained in your individual file as required l Supervisor s Investigation and Record of Incident if necessary 2 OSHA LOGs All recordable illnesses or injuries must be recorded within 7 calendar days of notification Monsanto OSHA 300A logs will be posted no later than February 1 of the year following the year covered by the records and keep the posting in place until April 30 Monsanto Self Inspections Log of Tool Box Talks Equipment Preventive Maintenance 3 4 5 6 Hazard Communication Compliance Plan 7 Material Safety Data Sheets 8 OSHA Training Records 9 OSHA Poster Explaining Employee Rights 10 Accident Forms Medical Records 11 Corporate Safety Manual amp Policy 12 Emergency Phone Number List 13 Site specific training 14 Work related fatalities Monsanto 15 Injury or near miss investigation form Monsanto 16 Illness investigation form Monsanto 17 Medical records retained for a minimum of 30 years post employment All records maintained for a minimum of 10 years in employee file will be reviewed and signed by a company offi
9. this Safety Manual amp Policy packet with the Employee listed below and understand that they have no questions or concerns of the contents of this packet requirements of them requirements of RME requirements of the safety director requirements of the superintendent requirements of the foreman and the requirements of their fellow employees at this time Corporate Management Signature Printed Name Date Safety Director Signature Printed Name Date Superintendent Foreman Signature Printed Name Date I have read the above policies and understand that cooperation between employees and management will ensure safe working conditions will help to result in injury free performance and will work to our mutual advantage Employee Signature Printed Name Date Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 2 0 DISCIPLINARY POLICY PROCEDURES Disciplinary procedures Punishments that society can impose generally fall under the headings of reprimand fines if authorized by law suspension or expulsion termination in employment It is the responsibility of the RME to insure that all incidents or actions that occur and are reported accordingly are addressed in accordance with this procedure no matter the severity It is the responsibility of the employees to report any incident or action that may need to be addressed by this policy no matter the severity This ensures that eve
10. to include Co Presidents and Co Vice Presidents Safety Director Responsible Managing Employee RME assigned by Corporate to manage the safety department policies as set forth in this manual Responsible Managing Employee RME An individual assigned by Corporate to manage individual tasks necessary to see that all policies are carried out as outlined in this manual Employee Any individual under the direct employment of Tri State Automatic Sprinkler Inc that is assigned to carry out any task given to them for any reason Job Site Any location where Tri State Automatic Sprinkler Inc requires employees to perform work to complete any task assigned to them Superintendent A person who manages or superintends an organization Foreman A person who directly supervises and directs other workers Self Inspection A self inspection is a rehearsal of one s areas by either oneself or by someone belonging to the department so as to find out the existing unsafe conditions A self inspection of the task at hand to insure all necessary tools equipment personnel and safety equipment are at the ready Home Office Main office of an organization also called headquarters Task A piece of work assigned or done as part of one s duties Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 SIGNATURE OF ACCEPTANCE OF SAFETY MANUAL amp POLICY Ihave reviewed the contents of
11. violation of this policy and is subject to being discharged with prejudice or severely disciplined as described herein Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 10 0 AMMONIA AWARENESS Ammonia also known as Azane amp Anhydrous Ammonia is a colorless gas with a pungent smell which is detectable in as little as 5 ppm concentrations It is Tri State s responsibility to educate you when you may be required to work on job sites that are known to contain ammonia and to the effects of direct contact with ammonia It is every employee s responsibility to watch out for ammonia and to report any suspected contact you have with ammonia that can cause you any ill effect Ammonia is both caustic and hazardous to your health and is an irritant to the nose eyes and skin It is readily absorbed into the moisture in the skin eyes and mucus membranes and in heavy concentrations can cause severe burns Any exposure can result in severe reactions Ammonia is commonly used as a coolant cleaner and fertilizer for many different facilities Ammonia is slightly flammable When handled properly ammonia is very safe and is considered one of the most environmentally safe refrigerants known today If you are working on any jobsite that does or may contain ammonia take the time to read the site specific contingency and or emergency plans set forth by the site contractor engineer architect or facility owner This may save yo
12. 013 7 Additional Safety Rules for Stepladders Never use a stepladder over 20 feet long Always open a stepladder completely and make sure the spreader is locked open before using the ladder Never substitute makeshift devices of wire or rope for stepladder spreaders Do not stand higher than the second step from the top of a stepladder Especially do not stand or sit on the top cap or stand on the pail shelf or on the back of a stepladder Do not straddle the front and back of a stepladder Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 27 0 SUBCONTRACTOR MANAGEMENT PLAN Subcontractor Management Plan Outlines the relationship between Contractors Tri State Automatic Sprinkler Inc and any subcontractor that may be employed to complete any specific scope of work or task assigned to them while working on a project contracted to Tri State Automatic Sprinkler Inc It is Tri State s responsibility to train all employees on the subcontractor management plan for any project that they may be assigned to how to follow this plan and all necessary procedures that they may be required to follow when implementing this plan It is every employee s responsibility to attend the provided training for this chapter understand the requirements that may be required of them and how to implement them for any subcontractor that is assigned to the project they may be working on Managing subcontractors is based on the f
13. 13 May 15 2013 10 11 SAFETY DIRECTOR RESPONSIBILITIES Monitor supervisory management and employee activity to ensure that the corporate programs are carried out in a timely manner Coordinate safety information between projects to ensure that all projects will benefit from each other s efforts Coordinate all safety activities including jobsite inspections and distribution of safety materials Perform jobsite inspections periodically and follow up corrective actions Maintain all accident records and complete all required OSHA forms Analyze accident records and show trends Promote safety education on all levels Periodically review safety rules and standards with employees to confirm that the company is meeting its goals and objectives Review with supervisors how to handle emergency procedures at each jobsite location Confirm that all required signs are posted and bulletin boards are maintained in clear and legible condition Confirm employer is enforcing compliance with all applicable federal state and local regulations Provide a regular report to upper management on the results of the safety program Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 10 11 12 13 SUPERINTENDENT FOREMAN RESPONSIBILITIES Know safety rules and work practices that apply to the work you supervise Take action to confirm that all employees in your charge understand the safety rules that apply to them Always ta
14. AZARDS THEY MAY BE EXPOSED TO ON THEIR JOBSITE ASK FOR THE INFORMATION AND STAY INFORMED Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 19 0 LOCK OUT TAG OUT Lock Out Tag Out A safety procedure which is used in industry and research settings to ensure that dangerous machines are properly shut off and not started up again prior to the completion of maintenance or servicing work It is Tri State s responsibility to supply you with the appropriate training and materials to complete a lock out tag out procedure on projects you are working that require this process It is every employee s responsibility to attend the training supplied by Tri State and to maintain their lock out tag out kit in good working condition in order to carry out this process when necessary Locking out equipment for service repairs additions modifications ect does not stop with large equipment machines that have multiple moving parts it also pertains to ensuring that the water supply for a fire sprinkler system that you are working on cannot become accidentally recharged with water once you have drained it for the task you have been assigned If you are working on a fire sprinkler system and is it not locked out for service repairs modifications etc an unsuspecting and well intentioned individual may see a system that has been accidentally left out of service and turn it back on resulting in potential damage to property or wor
15. Automatic Sprinkler Inc SM 2013 May 15 2013 17 0 POWER TOOLS Power Tools A tool that is actuated by an additional power source and mechanism other than the solely manual labor used with hand tools A tool actuated by an outside source of movement It is Tri State s responsibility to supply you with the appropriate tools and equipment to complete your assigned tasks in a safe and accurate manor while also adhering to our trades appropriate workmanship type manner It is every employee s responsibility to utilize the tools and equipment supplied to them to complete each task in a safe and accurate manor that will ensure each task is completed as prescribed and as efficient as possible The power tools utilized on jobsites can vary greatly from cordless drills to high speed core drilling machines that must be secured to the structure before use Your attention to detail when utilizing these tools is your greatest asset in assuring that no harm comes to you or the materials you are working on Although most power tools are not complicated to operate basic safety practices must be followed and the tools must be kept in proper operating condition Reviewing the manufacturers operation and maintenance documents should be completed at least annually by each employee operating that particular tool A complete list of these documents can be found on the employee portal www tri statesprinkler com Employees using hand and power t
16. CI DEVICES ON PORTABLE ELECTRIC DRIVE TOOLS Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 25 0 BLOOD BORNE PATHOGENS Blood borne Pathogens Microorganisms that can cause diseases such as human immunodeficiency virus HIV and hepatitis B HBV which are spread through contact with infected blood or blood products It is Tri State s responsibility to train you on potential blood borne pathogen exposures and what to do to avoid these exposures Training will be conducted before initial assignment on any project and annually thereafter It is every employee s responsibility to attend the provided training to follow guidelines set forth when the potential for self exposure is evident and to know where to find the TASI exposure control plan Blood borne pathogens are a possibility on every jobsite you are asked to work on If a fellow employee accidently receives a cut and they require general first aid or emergency services you are facing a possibility of exposure to any known or unknown pathogens they may have Your exposure is not limited to direct contact with their person they can contaminate any equipment or material they are handling as well Be sure you handle everything they are touching as contaminated to minimize everyone s exposure Any PPE required will be made at no cost to the employee If your first aid kit does not contain a basic blood borne pathogen safety kit notify your direct sup
17. K ON SCAFFOLDING THAT HAS NOT BEEN ERECTED INSPECTED AND CERTIFIED BY A LICENSED COMPANY NO TRI STATE EMPLOYEE IS AUTHORIZED TO ERRECT INSPECT OR TAKE CORRECTIVE ACTION ON ANY SCAFFOLDING SYTEM OR ITS COMPONENTS Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 23 0 AERIAL LIFTS Aerial Lifts Any vehicle mounted device telescoping or articulating or both which is used to position personnel including extensible boom platforms aerial ladders articulating boom platforms or vertical towers It is Tri State s responsibility to supply adequate aerial lift equipment for every employee to utilize while completing the tasks given to them and to train them on pre use inspections of that equipment and to supply adequate training on all aerial lift equipment that may be utilized on any project site It is every employee s responsibility to attend the required training on aerial lifts complete the pre use inspections as required operate all aerial lifts in a safe manner and to utilize all aerial lifts for the purpose in which they are designed or intended Aerial lifts are very powerful machines that are a useful tool on many different types of projects for many different reasons When used correctly and in a safe manner these pieces of equipment can provide quick and easy access to work areas that were once almost impossible to reach Tri State shall provide training to every employee on all types of lift equi
18. Tri State Automatic Sprinkler Inc Safety Manual TRI STATE AUTOMATIC SPRINKLER 5570 CAREY AVENUE DAVENPORT IOWA 52807 PHONE 563 386 8707 FAX 563 386 8769 TRI STATE Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 SAFETY MANUAL TABLE OF CONTENTS Sections 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 10 0 11 0 12 0 13 0 14 0 15 0 16 0 17 0 18 0 19 0 Corporate Management Policy Policy Statement Corporate Responsibilities Safety Director Responsibility Superintendent Foreman Responsibility Employee Responsibility Definitions Disciplinary Policy Procedures New Employee Training Competent Person Designation Accident Reporting and Investigation Recordkeeping Toolbox Talks Self Inspections Drug and Alcohol Policies Ammonia Awareness Asbestos Awareness Lead Awareness Electric Safety Fall Protection Fire Protection Prevention Basic First Aid Power Tools Hazard Communication HAZCOM Lock out Tag out Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 20 0 21 0 22 0 23 0 24 0 25 0 26 0 27 0 28 0 29 0 30 0 31 0 32 0 Noise Exposure Hearing Conservation Personal Protective Equipment PPE Scaffolding Aerial Lifts Assured Equipment Grounding Conductor Blood borne Pathogens Ladder Safety Subcontractor Management Plan Process Safety Management Contractor Responsibilities Welding Cutt
19. agreed upon between all involved employees before beginning the work at hand NO TRI STATE EMPLOYEE IS AUTHROIZED TO COMPLETE REPAIRS ON ANY ELECTRIC DEVICE OR TOOL FOR ANY REASON TRI STATE DOES NOT EMPLOY ANY PERSONS WHO ARE QUALIFIED TO WORK ON NEAR OR APPROACH ANY OVERHEAD POWER LINES FOR ANY REASON WHATSOEVER STAY AWAY FROM OVERHEAD POWER LINES Take precautions and be informed as to the hazards of your surroundings Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 14 0 FALL PROTECTION Fall Protection Is a system designed to protect personnel from the risk of falls when working at heights of six 6 or greater in height from the working platform The objective of this fall protection program is to identify and evaluate fall hazards to which employees will be exposed and to provide specific training as required It is Tri State s responsibility to provide fall protection to affected employees and to ensure that all employees understand and adhere to the procedures of this plan and follow the instructions of the RME It is every employee s responsibility to follow these guidelines and to ensure that they remain responsible for their own safety by Understanding and adhering to the procedures outlined in this program Following the instructions of their direct supervisor and or RME when implementing these procedures Bringing to management s attention any unsafe or hazardous conditions or practic
20. all distance to two 2 feet or Sustain a minimum tensile load of 5000 pounds includes ripstitch tearing and deforming lanyards Anchorages must support at least 5000 pounds per person attached and shall be Designed installed and managed by a certified Professional Engineer Capable of supporting twice the weight expected to be imposed on it Independent of any anchorage used to support or suspend platforms Positioning Device Systems Body belt or body harness systems shall be set up so that an employee can free fall no farther than two 2 feet and shall be secured to an anchorage capable of supporting twice the potential impact load or 3000 pounds whichever is greater Warning line systems consisting of supporting stanchions and ropes wires or chain shall be erected around all sides of roof work areas and shall only be used when approved by the job site AHJ or site specific engineer and shall conform with the following Lines shall be flagged at no more than six 6 foot intervals with high visibility materials The lowest point of the line including sag shall be between 34 and 39 inches from the walking working surface Stanchions of warning line systems shall be capable of resisting at least 16 pounds of force Ropes wires or chains must have a minimum tensile strength of 500 pounds Warning line systems shall be erected at least six 6 feet from the edge except in areas where mechanical equipment is in use When mech
21. anical equipment is in use warning line systems shall be erected at least six 6 feet from the parallel edge and at least ten 10 feet from the perpendicular edge NO TRI STATE EMPLOYEE IS AUTHROIZED TO MODIFY OR COMPLETE REPAIRS ON ANY FALL PROTECTION SYSTEM FOR ANY REASON Take precautions and be informed as to the hazards of your surroundings Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 15 0 FIRE PROTECTION amp PREVENTION Fire Protection The study and practice of mitigating to make less severe the unwanted effects of potentially destructive fires from occurring Fire Prevention To take precautions to prevent potentially harmful fires from occurring and to be educated about surviving them When combined these two terms are utilized on all work sites to maintain a clean organized hazard free area that has minimal chances of producing any unwanted fires from occurring and if they do what to do to survive them Potential fire hazard materials Materials that can readable be ignited by a spark or ignition source These materials can be solids liquids or gases Ignition sources A device or item that is capable of generating sparks or enough heat to produce combustion Fire protection equipment Any apparatus machinery or appliance intended for use by a fire service unit in fire prevention or suppression activities Good Housekeeping General care cleanli
22. arrest systems shall be issued to and used by employees as determined by Responsible Person and may consist of anchorage connectors body harness deceleration device lifeline or suitable combinations Personal fall arrest systems shall meet the requirements as set forth in OSHA fall protection standards and as required by site specific requirements All components of a fall arrest system shall meet the specifications of the OSHA Fall Protection Standard and shall be used in accordance with the manufacturer s instructions and shall adhere to the following list of requirements Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 The use of non locking snap hooks is prohibited Dee rings and locking snap hooks shall have a minimum tensile strength of 5000 pounds be proof tested to a minimum tensile load of 3600 pounds without cracking breaking or suffering permanent deformation Lifelines shall be Designed installed and used under the supervision of the RME Protected against cuts and abrasions Equipped with horizontal lifeline connection devices capable of locking in both directions on the lifeline when used on suspended scaffolds or similar work platforms that have horizontal lifelines that may become vertical lifelines Self retracting lifelines and lanyards must have ropes and straps webbing made of synthetic fibers and shall Sustain a minimum tensile load of 3600 pounds if they automatically limit free f
23. at you and your fellow workers will not come to harm because of misplaced intentions of uninformed individuals All training will be documented signed and maintained for a minimum of 10 years in the employees file It only takes a few minutes to save a lifetime of regret Take those minutes to ensure your as well as your fellow employee s safety EVERY EMPLOYEE IS REQUIRED TO UTILIZE THE LOCK OUT TAG OUT PROCEDURES ON ALL SOURCES OF ENERGY LINKED TO THE TASK THEY ARE COMPLETING Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 20 0 NOISE EXPOSURE HEARING CONSERVATION Noise Any sound that is undesired or interferes with one s hearing of something Exposure The condition of being present to hear or view something weather favorable or unfavorable Hearing Conservation Any program undertaken to preserve hearing and to prevent hearing loss through public education screening programs to identify persons needing attention and through the reduction of occupational hazards that pose a threat to a workers hearing It is Tri State s responsibility to limit as much as possible every employee s exposure to excessive noise train every employee on identifying the potential need for proper hearing protection identifying the need for potential hearing protection defining what type of hearing protection may be needed and how to dawn it for all employees exposed to potentially hazardous noise
24. ate s direct assumption that all employees are responsible for themselves and their fellow workers safety through their actions in preventative planning on all job sites Competent Person List 1 Project Manager 2 Superintendant 3 Project Foreman 4 Individual completing task at hand Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 5 0 ACCIDENT REPORTING AND INVESTIGATION Accident Reporting The process of recording the details of any accident that occurred that may or may not have resulted in the injury of persons or property Accident Investigation A detailed defined and recorded review of an occurrence Completed to uncover and record the factors and causes and their relationships which led up to and caused an accident or incident It is the responsibility of Tri State to assign a competent RME to complete all accident investigations no matter the severity All reported accidents will be subject to an accident investigation Tri State will provide all required training on accident investigation to a competent RME The superintendent and all employees witness to the accident or not working on the jobsite where the accident occurred will make a documented report of every accident within twenty four 24 hours of the occurrence Reports are to be completed as soon as possible to avoid changes in physical conditions minimize whiteness discrepancies and maximize evidence retention if necessary
25. attached to the boom or basket load point as indicated in the user s manual Test controls before each use Ensure that the backup alarm notification device is working correctly if not then a spotter must be used when backing up the equipment NEVER Operate any aerial lifts above other personnel NEVER Overload any baskets platforms refer to the operators manual for load limits on the equipment you are operating Utilize equipment to lift materials or other equipment Make modifications to any equipment for any reason Repairs and modifications are Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 only to be completed by factory trained personnel Operate any aerial lift within 10 of any electrical lines Stand of railings of lift baskets to perform any work If the equipment you are operating cannot reach your working elevation you need to notify your direct supervisor so that the correct equipment can be obtained to allow you to complete your task in a safe manner ONLY PROPERLY TRAINED PERSONNEL ARE TO OPERATE ANY AERIAL LIFT EQUIPMENT NO TRI STATE EMPLOYEE IS ALLOWED TO MAKE MODIFICATIONS TO ANY LIFT EQUIPMENT FOR ANY REASON Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 24 0 ASSURED EQUIPMENT GROUDNING CONDUCTOR PROGRAM or GROUND FAULT CIRCUIT INTERRUPTER GFCD Assured Equipment Grounding Conductor or Ground Fault Circuit Interrupter GFCD A device for the protection o
26. ble cords may not be run through windows or doors unless protected from damage and then only on a temporary basis Flexible cords may not be run above ceilings or inside or through walls ceilings or floors and may not be fastened with staples or otherwise hung in such a fashion as to damage the outer jacket or insulation e Cords must be covered by a cord protector or tape when they extend into a walkway or other path of travel to avoid creating a trip hazard e Extension cords used with grounding type equipment must contain an equipment grounding conductor 1 e the cord must accept a three prong or grounded plug e Attachment plugs and receptacles may not be connected or altered in any way that would interrupt the continuity of the equipment grounding conductor Additionally these devices may not be altered to allow the grounding pole to be inserted into current connector slots Clipping the grounding prong from an electrical plug is strictly prohibited e Flexible cords may only be plugged into grounded receptacles The continuity of the ground in a two prong outlet must be verified before use It is recommended that the receptacle be replaced with a three prong outlet Adapters that interrupt the continuity of the equipment grounding connection may not be used e All portable electric equipment and flexible cords used in highly conductive work locations such as those with water or other conductive liquids or in places where employees are
27. ce know what to do if exposed to potential hazards and communicate potential exposures to their direct supervisor before any exposures do occur It is also every employee s responsibility to identify read and decipher all warning labels posted on every jobsite that they are working on Any label on chemicals that are being supplied by Tri State must be maintained and placed for easy access to all employees on every jobsite they are utilized on Every jobsite you are asked to work on contains hazards of some kind Some are minimal and some are extreme If you are working on a jobsite and suspect that you are or may become in contact with a controlled product ask for the MSDS forms so you know what to do and what to look for in that particular product Tri State shall maintain a list of hazardous chemicals on the job site A list of the hazardous chemicals known to be present using an identity that is referenced on the appropriate Safety Data Sheet All non routine tasks completed by other trades will be communicated to all employees working on a given job site through written notification This notification will be issued to each employee explaining the task chemicals used potential contamination occurrences and any contact symptoms that are possible This data must be supplied to Tri State by the facility owner and communicated to all employees working on the effected project site EVERYONE WORKING ON EVERY JOBSITE HAS THE RIGHT TO KNOW THE H
28. cer Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 7 0 TOOL BOX TALKS Tool Box Talks A short weekly discussion or presentation given by job site foreman or an RME appointed by them that generally lasts no longer than 10 minutes This talk is focused on one specific topic that is usually site specific in use It is Tri State s responsibility to provide adequate topics and supporting documentation to give the job site foreman the tools to complete these training sessions It is the responsibility of every employee on every job site to ensure that these talks are completed It is the direct responsibility of the project foreman to ensure that these talks are signed by everyone in attendance and turned in each week as required by the company superintendent There is not specific training requirements for anyone to complete these weekly talks Tool box talks of 5 to 10 minutes must be held by the foreman each week Employees never receive too much training and therefore our company relies upon jobsite management to provide ongoing and continuous employee training These signed and dated tool box talks are to be turned in each week with the project foreman s timesheet and will be kept as part of your for all in attendance formal training record documentation As much possible the subject to each training talk should be chosen to relate to the type of work that is being performed Toolbox talks will be handed o
29. dder for the job and includes inspection setup proper climbing and standing proper use care and storage In addition to the general safety rules for all ladders there are special rules for using stepladders and for single and extension ladders 1 Ladder Selection Be sure the ladder being used has the proper duty rating to carry the combined weight of the user and the material being installed A ladder s duty rating tells you its maximum weight capacity There are four categories of duty ratings Type IA These ladders have a duty rating of 300 pounds Type IA ladders are recommended for extra heavy duty industrial use Type I These ladders have a duty rating of 250 pounds Type I ladders are manufactured for heavy duty use Type II These ladders have a duty rating of 225 pounds Type II ladders are approved for medium duty use Type III These ladders have a duty rating of 200 pounds Type II ladders are rated for light duty use Type IA and Type I ladders are the only acceptable ladders on a construction jobsite The American National Standards Institute ANSI requires that a duty rating sticker be placed on the side of every ladder so users can determine if they have the correct type ladder for each task job Be sure that metal steps and rungs are grooved or roughened to prevent slipping Be sure that the ladder you have chosen for your job is acceptable to be used on the project you are working on Ladders shall only be u
30. desirable event that could result in damage to person or property It is Tri State s responsibility to train you on your rights regarding our Stop Work action plan It is every employee s responsibility to be aware of their rights regarding the Stop Work action plan and to implement them whenever they see the need The Stop Work action plan is available to every employee working on any jobsite anywhere If you ever witness an action or proposed actions that may result in damage to persons or property implement the Stop Work action plan and eliminate the potential for harm No matter what your position is on any jobsite if you ever see any action being carried out or planned that you think will result in the harm or personnel or property STOP WORK and talk about it with everyone involved It may save a life EVERY EMPLOYEE WORKING FOR TRI STATE AUTOMATIC SPRINKLER INC HAS THE RIGHT TO STOP WORK WHEN THEY SEE POTENTIAL DANGER EVERYONE Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 25 0 MATERIAL SAFETY DATA SHEETS MSDS Material Safety Data Sheets MSDS Forms intended to provide workers and emergency personnel with procedures for handling or working with that substance in a safe a manner includes information such as physical data storage disposal protective equipment and spill handling procedures It is Tri State s responsibility to ensure up to date MSDS forms are provided for all con
31. e of Ladders Never use metal ladders around exposed electrical wiring Metal ladders should be marked with tags or stickers reading CAUTION Do Not Use around Electrical Equipment or similar wording RULE of THUMB If the overhead Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 power line is 50 kV or less then stay at least 10 feet away For everything else keep at least 35 feet away When using a ladder where there is traffic erect warning signs or barricades to guide traffic away from the foot of the ladder If this is not possible have someone hold and guard the bottom of the ladder Do not try to move a ladder while you are on it by rocking jogging or pushing it away from a supporting wall Never use a ladder when under the influence of alcohol on drugs or medication or in ill health If you get sick dizzy or panicky while on a ladder do not try to climb down in a hurry Wait Drape your arms around the rungs rest your head against the ladder until you feel better Then climb down slowly and carefully Do not leave tools or materials on top of ladders If they fall on you you can be hurt If they fall on someone else your company can be sued Never push or pull anything sideways while on a ladder This puts a side load on the ladder and can cause it to tip out from under you Allow only one person at a time on a ladder unless the ladder is specifically designed for two people Never use a ladder as a horizonta
32. e this and to provide a safe workplace for all of our employees and anyone working around you All employees are required to make daily visual inspections of their work areas and to test all equipment for proper operation prior to the start of the task at hand Corrective action must be completed immediately if any hazards do exist Test your tools and equipment in accordance with manufactures recommendations for proper operation and performance Any equipment indicating signs of being unsafe and cannot be properly repaired before being utilized then it must be removed from service marked accordingly and proper notification given to your direct supervisor so that the replacement process for that particular piece of equipment or tool can begin ALL equipment that needs repaired must be returned to the home office for repair or replacement DO NOT THROW AWAY TOOLS OR EQUIPMENT FOR ANY REASON All work areas including office areas will be inspected utilizing this process If any hazardous conditions are noted corrective action must be taken If the corrective action is beyond our authority and or capability keep all employees away from the hazardous condition until it is corrected or controlled Notify your direct supervisor in writing texts and email are acceptable to request corrective action RMEs are expected to follow up on reported hazards to make sure they have been eliminated or controlled Lack of appropriate inspections as well as fa
33. entation and that I understand this information Employee Signature Management Signature Employee Name Written Management Name Written Date Date Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 4 0 COMPETENT PERSON DESIGNATION Competent Person One who is capable of identifying existing and predictable hazards in the surrounds or working conditions which are unsanitary hazardous or dangerous to employees and who has authorization to take prompt corrective measures to eliminate them It is the responsibility of Tri State to appoint an individual as a competent person in accordance with definitions listed in this policy It is the responsibility of the competent person to follow through with their assigned duties as described here in and carry out any if any actions needed to insure a safe and healthy working environment for all employees It is the responsibility of the employee to follow the direction of the competent person assist the competent person in identifying any unsafe or hazardous working conditions that exist or may occur in the future and to aid them in removing or avoiding these conditions to assure a safe and healthy working environment for themselves and their fellow employees There is the possibility that more than one competent person may be necessary depending on the range of hazards on the project the size of the project and the distance between operations on a project It is Corpor
34. ervisor so that one can be made available to you If your jobsite does not have a sterile wash station for your use notify your direct supervisor and they will either make one available to you or supply you with antiseptic solutions towelettes All employees will have access to the exposure control plan for the project they are working on Tri State shall make available at no cost the hepatitis B vaccine and vaccination series to all employees who have occupational exposure and post exposure evaluation and follow up to all employees who have had an exposure incident while working on any TASI project site All medical notes records for all employees are kept for a minimum of 30 years post employment All training records are kept for a minimum of 10 years In reference to blood borne pathogens if you are going to administer first aid you should always do the following Consider everyone a potential source of blood borne pathogens no matter what Consider all bodily fluids a potential source of blood borne pathogens no matter what Keep your eye protection on to limit potential exposure with your eyes Wear rubber latex gloves when handling the individual or equipment Cover any exposed wounds that are oozing or squirting blood with the gauze cloth provided in your first aid kit Minimize your exposure to potentially contaminated items by keeping them at a safe distance or disposing of them in biological hazardous waste contai
35. es that may cause injury to either themselves or their fellow employees Report any incident that causes injury to an employee regardless of the nature of the injury All employees who may be exposed to fall hazards 6 in height or more are required to receive training on how to recognize such hazards and how to minimize their exposure to them Employees shall receive training as soon after employment as possible and before they are required to work in areas where fall hazards exist Additional training shall be provided on an annual basis or as needed when changes are made to this program or where site specific requirements dictate they are completed All training completed will be documented and maintained in the employee s permanent file Site specific fall protection plans will be provided by a qualified individual trained in accessing the site situation and providing an adequate plan to safely complete all tasks at hand All fall protection plans shall be designed to insure that prompt rescue is possible in the event of a fall Prompt rescue can be completed by personnel not involved in the task at hand or be planed so that the individual completing the task at hand can rescue themselves Fall Protection Systems Guardrails mid rails screens mesh intermediate vertical members and solid panels shall be erected in accordance with the OSHA standards by personnel certified and trained in that particular system Personal fall
36. f personnel that functions to de energize a circuit or portion thereof within an established period of time when a current to ground exceeds some predetermined value that is less than that required to operate the over current protective device of the supply circuit It is Tri State s responsibility to supply adequate GFCI devices or internal or external to the tool being utilized to all employees to utilize when completing the tasks assigned to them and to provide annual training on the proper use and care of these devices It is every employee s responsibility to attend the required training on GFCI devices complete the pre use inspections as required operate all electric driven tools in a safe manner and to utilize all electric drive tools for the purpose in which they are designed or intended Unless the jobsite you are working on contains a assured equipment grounding conductor program all employees are required to utilize ground fault circuit interrupters GFCI devices when operating electric drive equipment 1 e portable power tools extension cords power machines drills etc Ground fault circuit interrupters shall Be inspected before each use Be tested before each use Be utilized on all 120v or 240v single phase 15 amp and 20 amp receptacles within 6 feet of any possible water source Be utilized on all portable electric tools and extension cords ALL TRI STATE EMPLOYEES ARE REQUIRED TO UTALIZE GF
37. ge hazards associated with the process industries and is intended to reduce the frequency and severity of incidents resulting from releases of chemicals and other energy sources Primarily composed of organizational and operational procedures design guidance audit programs and a host of other methods for the purpose of control It is Tri State s responsibility to provide training for every employee on the standards of process safety management and how they pertain to every level of every individual involved to insure job performance is maximized while minimizing potential hazardous releases It is every employee s responsibility to complete the provided training know their roll while working on any jobsite in regards to process safety management and to carry out those responsibilities as assigned to them Process Safety Management or PSM is a tool utilized to minimize the potential for fires explosions releasing toxic substances avoid fatalities and reduce the risk of property damage that may result from the release from the release of chemicals All employees will Trained to perform their job training will be documented Instructed in hazards related to their jobs and potential fire explosive or toxic release hazards Follow all safe work practices such as lockout tagout confined space entry opening process equipment or piping and control over entrance to any facility Notify your direct supervisor is any hazards are f
38. glass type Wait until the air is calm enough to insure safety Never set up a ladder in front of a door unless the door is locked or a guard is posted Do not use ladders on ice or snow unless absolutely necessary If they must be used on ice or snow use spike or spur type safety shoes on the ladder feet and be sure they are gripping properly before climbing Use Safety shoes on ladder feet whenever there is any possibility of slipping Utilize the 4 1 setup ratio when setting up any extension ladder 4 Ladder Climbing and Standing Keep the steps and rungs of ladders free of grease oil wet paint mud snow ice paper and other slippery materials Also clean such debris off your shoes before climbing a ladder Always face a ladder when climbing up or down Use both hands and maintain a secure grip on the rails or rungs Never carry heavy or bulky loads up a ladder Climb up yourself first and then pull up the material with a rope Climb and stand on a ladder with your feet in the center of the steps or rungs Do not overreach from a ladder or lean too far to one side Overreaching is probably the most common cause of falls from ladders A good rule is to always keep your belt buckle inside the rails of a ladder Work as far as you can reach comfortably and safely then move the ladder to a new position Never climb onto a ladder from the side from above the top or from one ladder to another Never slide down a ladder 5 Proper Us
39. hich is usually the earliest symptom of lung cancer Other cancers have been noted in a smaller number of individuals who were exposed to Asbestos fibers In 1991 the direct use of Asbestos was banned for use in the following flooring felt roll board and corrugated commercial or specialty paper In addition the regulation continues to ban the use of asbestos in products that have not historically contained asbestos otherwise referred to as new uses of asbestos Asbestos is required to be marked with an OSHA approved label however that is not always the case If you suspect any materials floor tile ceiling tile panel insulation piping insulation tank insulation acoustical ceiling spray sound insulation spray etc of containing asbestos do not disturb it Report your suspicions to your direct supervisor for immediate investigation and follow up Asbestos awareness training is required for all employees whose work activities may come in contact with asbestos containing materials or any materials that are presumed to contain asbestos but do not disturb the asbestos during their work activities Asbestos awareness training is required for all employees who work in areas that contain or may contain asbestos All training completed will be documented and maintained in the employee s permanent file Abide by all warning signs and labels posted on all jobsites Any equipment has the potential to contain asbestos read the warn
40. ing Hot Work Stop Work Material Safety Data Sheets MSDS Forms Supervisor s Accident Investigation Report Employee Accident Report Employee Incident Near Miss Report Employee Report of Injury Jobsite Safety Analysis JSA Disciplinary Action Form Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 1 0 CORPORATE MANAGEMENT POLICY POLICY STATEMENT The personal safety and health of each employee of our organization is of primary importance We believe that our employees are our most important assets and that their safety on every job site is our greatest responsibility The prevention of occupationally induced injuries and illnesses is of such consequence that it will be given precedence over operating productivity whenever necessary Management will provide all mechanical and physical facilities required for the personal safety and health of each of its employees Everyone who conducts the affairs of Tri State Automatic Sprinkler Inc no matter in what capacity they function is expected to fully accept this policy and the responsibilities it implies upon us all Employees are expected to use the safety equipment provided and to obey the rules of conduct safety and health Safety equipment must not be abused or destroyed Cooperation between our employees and management in the observance of this policy will ensure safe working conditions help to result in accident free performance and will work to our mutual advantage
41. ings and stay safe When working on multi contractor worksites employees shall be protected from exposure to any and all known contamination situations that may exist If employees working immediately adjacent to a Class I asbestos jobs are exposed to asbestos due to the inadequate containment of such job Tri State shall remove the employees from the area until the enclosure breach is repaired NO TRI STATE EMPLOYEE IS AUTHROIZED TO DISTURB ASBESTOS CONTAINING MATERIALS FOR ANY REASON If you are working near or on any item that you suspect to contain asbestos stop work and notify your direct supervisor immediately Take precautions and be informed as to the hazards Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 12 0 LEAD AWARENESS Lead A naturally occurring heavy bluish metal that has been used for centuries in a myriad of products Lead is nearly indestructible and is not biodegradable It is odorless and tasteless and only detectable through testing It is Tri State s responsibility to educate you when you may be required to work on job sites that are known to contain lead and to the effects of direct contact with lead It is every employee s responsibility to watch out for lead and any items you suspect to contain lead and to report any suspected contact you have with lead Lead is commonly used in many different products like batteries solder pottery glazing window glazing and paint Today lead i
42. ke immediate action to correct safety rule violations Unsafe acts or procedures cannot be tolerated Prevent bad work habits from developing You are responsible to make daily observations of employees to ensure that they perform their work safely and continue this observation regularly once safe working habits are established Take action to correct or control hazardous conditions within your work areas If itis beyond your control remove the employee until the condition is safe Eliminate unsafe conditions and prevent an accident Encourage workers to report unsafe conditions or procedures Listen to your workers and don t take their safety complaints lightly No job should proceed when a question of safety remains unanswered Seek advice from your project manager when necessary Set a good example Demonstrate safety in your own work habits and personal conduct Always wear personal protective equipment in areas where personal protective equipment is required Train your employees on the proper safety procedures to follow including the use of additional safeguards such as machine guards and personal protective equipment Investigate and analyze every accident however slight that occurs to any of your employees Control the causes of minor incidents to help avoid future crippling accidents Complete and file a report on each and every incident and accident that occurs at your jobsite If you have a question or require reporting forms con
43. l platform plank scaffold or material hoist Be cautious about homemade ladders Never use ladders made by fastening cleats across a single narrow rail post or pole Never use a ladder on a scaffold platform If you need to reach higher the scaffold should be higher 6 Proper Ladder Care and Storage Maintain ladders in good condition Keep all ladder accessories especially safety shoes in good condition Wood ladders which are to be used outside should be treated to prevent weather damage A clear finish or transparent penetrating preservative should be used Linseed oil is a good treatment for a wood ladder although it does add some weight to the ladder An oil treatment also helps to rustproof the metal parts of a wood ladder Never paint a wood ladder This will cover dangerous cracks or fill and hide them Never sit on ladder side rails Never use a metal or fiberglass ladder which has been exposed to fire or strong chemicals it should be discarded Never store materials on a ladder Store wood ladders where they will not be exposed to excessive heat or dampness Store fiberglass ladders where they will not be exposed to sunlight or other ultraviolet light sources Be sure that ladders are properly supported and secured when in transit Vibration and bumping against other objects can damage them Store ladders on racks which give them proper support when not in use Tri State Automatic Sprinkler Inc SM 2013 May 15 2
44. likely to contact water or conductive liquids must be approved for those locations e Employee s hands must be dry when plugging and unplugging flexible cords and cord and plug connected equipment if energized equipment is involved The following are guidelines to adhere to when working on any project task e Employees who face a risk of electric shock but who are not qualified persons shall be trained and familiar with electrically related safety practices as they pertain to the task at hand e Safe work practices shall be employed to prevent electric shock or other injuries resulting from either direct or indirect electrical contacts when work is performed near or on equipment or circuits which are or may be energized e Conductors and parts of electrical equipment that have been de energized but not been locked or tagged out shall be treated as live parts e Take extreme caution when working on or near exposed energized parts Insure that the equipment has been isolated for movement into your work space or that it is fully de energized so that no movement of parts is possible Also insure that no energized parts are present in your work space Eliminate the possibilities of electric shock and collision with moving parts e Remember that only qualified personnel are allowed to work on or test energized parts e When working directly under overhead power lines or within 50 to either side of existing overhead power lines the lines MUST be de
45. lsification of inspection forms are a violation of company procedure and may be a civil and or criminal violation of federal and or state laws and or regulations making that individual subject to penalties fines prosecution or termination in employment The attached Self Inspection form is a aid to assist you in completing these inspections Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 9 0 DRUG AND ALCOHOL POLICIES Drugs A substance that has a physiological effect when ingested or otherwise introduced into the body Alcohol A colorless volatile flammable liquid that is the intoxicating constituent of wine beer amp spirits It is Tri State s responsibility to educate you as to the negative effects of drugs and alcohol use when working on any job site It is the responsibility of all employees to abstain from the use of drugs and alcohol while reporting to work on any job site at any time for any reason Drugs and alcohol impair your ability to make decisions in a timely manner and can result in the unnecessary loss of life and property Workers who report to work under the effects of drugs or alcohol are directly putting themselves and their fellow workers in danger Any employee caught reporting to work under the influence of drugs or alcohol will be subject to disciplinary actions as described in this policy Any employee who is in possession of drugs or alcohol on any jobsite is in direct
46. ments as described herein Any employee who uses drugs or alcohol on the job or works under the influence of drugs or alcohol endangers himself herself and other workers Tri State Automatic Sprinkler Inc follows a zero tolerance for the use of drugs or alcohol on any job site and will enforce the third offense policy for anyone caught abusing this policy requirement The above procedure has been prepared so that there is no question about how violations of rules regulations and procedures will be handled by management and so that employees will know what to expect if they do not comply with the established rules regulations and procedures Management knowledge of unsafe behavior and lack or appropriate documented discipline may be a violation of federal state laws and regulations and are expected to be addressed appropriately Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 3 0 NEW EMPLOYEE TRAINING New Employee Any person entering the employment of Tri State either for the first time or for re employment Training Teaching person s a particular skill set or type of behavior It is the responsibility of the RME to provide the appropriate training for all new employees regarding this and any other policy that they may be required to understand and adhere to It is the responsibility of the new employee to read and understand this and any other policies that they may be required to work under and adhere to on a
47. n 6 months of initial exposure Establish address where employees will be contacted are to be notified in writing when a standard threshold shift has occurred Supply hearing protection to all employees subject to 85 decibels or not free of charge as stated in other chapters for the purpose of protecting their hearing from any exposures to potential hearing loss At least annually after obtaining the baseline audiogram the employer shall obtain a new audiogram for each employee and notify that employee within 10 working days of any changes in the testing results be they positive or negative Unless a physician determines that any negative shifts in the audiogram that have taken place are not work related Tri State shall insure that the following steps are taken If not already utilizing hearing protection the employee shall be fitted Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 with hearing protection and trained on the proper usage and care of the device If already utilizing hearing protection the employee shall be refitted with hearing protection and retrained on the proper usage and care of the device The employee may be referred for a clinical audiological evaluation or an ontological examination as appropriate if additional testing is necessary or if the employer suspects that a medical pathology of the ear is caused or aggravated by the wearing of hearing protectors Evaluate hearing protector attenuation fo
48. ners if present Do not handle potentially contaminated equipment If equipment does appear to be Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 contaminated mark it as unsafe so that it can be properly disinfected by trained personnel Remove protective equipment you are wearing if it does become contaminated Wash your hands thoroughly after coming in contact with contaminated items If your project site does not have hand washing sites available notify your direct supervisor so that one can be made available to you BLOOD BORNE PATHOGENS ARE A VERY REAL RISK ON ANY PROJECT SITE TAKE EXTREME PRECAUTIONS WHEN YOU THINK YOU ARE AT RISK OF CONTACT WITH ANY POTENTIAL SOURCE Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 26 0 LADDER SAFETY Ladder A structure consisting of a series of bars or steps between two lengths or wood metal or rope used for climbing up or down for a means of access or egress of personnel It is Tri State s responsibility to train you on the appropriate use and care of ladders on an annual basis to provide every employee with any necessary lift equipment or ladder to safely complete the tasks assigned to them It is every employee s responsibility to attend the provided training to follow guidelines set forth when utilizing ladder systems and to report any damaged or broken ladder to their direct supervisor Ladder safety begins with the selection of the proper la
49. ness orderliness and maintenance of business or property It is Tri State s responsibility to complete training on the fire protection and prevention methods and procedures identified here in and any site specific requirements that you may be required to follow It is also Tri State s responsibility to provide the necessary materials equipment and procedures for the employees to utilize to adhere to these requirements It is every employee s responsibility to read understand and follow the requirements of this policy as described herein This section serves to aid you in reducing the risk of fires By being familiar with the general terms and responsibilities you are better able to carry out these requirements The following list can aid you in identifying these Identify materials that are potential fire hazards and their proper handling and storage procedures Distinguish potential ignition sources and the proper control procedures of those materials Describe fire protection equipment and or systems used to control fire hazards Identify persons responsible for maintaining the equipment and systems installed to prevent or control ignition of fires Identify persons responsible for the control and accumulation of flammable or combustible material Describe good housekeeping procedures necessary to insure the control of accumulated flammable and combustible waste material and residues to avoid a fire emergency Provide training
50. nt manner Tri State will not erect or require any employee to work on repair inspect or certify any scaffolding platform or structure in any manor other than as directed herein Before starting any task that requires scaffolding and scaffolding platforms ensure that it has been erected inspected and certified by a licensed scaffolding erection company in accordance with all necessary required codes All scaffolding is required to have a tag on it near the point of entrance indicating the condition of the scaffolding If the scaffolding you are about to work on does not have a tag indicating that it has been inspected as required Stop Work and notify your direct supervisor so corrective action can be taken Training shall be provided by qualified persons to all employees regarding the hazards of scaffolding Training program will include hazards fall electrical falling objects fall protection use and load capacity Hazards including fall protection electrical safety falling object protection scaffold use and load capacity will be addressed Retraining is required in at least the following situations 1 where changes at the worksite present a hazard about which an employee has not been previously trained or 2 where changes in the types of scaffolds fall protection falling object protection or other equipment present a hazard about which an employee has not been previously trained NO TRI STATE EMPLOYEE IS AUTHORIZED TO WOR
51. ntain keep clean and a necessary supply on your person on a daily basis If you are ever working on any jobsite that requires PPE that you were not normally issued notify your direct supervisor so necessary supplies can be ordered for you No employee owned PPE is allowed on any project site for any reason Tri State shall provide all required PPE No exceptions Monsanto Each employee who may or may not need to wear PPE will be trained on the proper wear and care of all PPE they may or may not be required to utilize to protect themselves Monsanto Retraining will be conducted when the workplace changes making the earlier training obsolete the type of PPE changes or when the employee demonstrates lack of use improper use or insufficient skill or understanding Monsanto PPE training is documented Monsanto Hazard assessment is signed by the project foreman Monsanto PPE must be fitted to each affected employee Monsanto Defective or damaged equipment shall not be utilized for any propose on any project site Dispose of it immediately and notify your direct supervisor Monsanto Each hazard assessment will be signed by all necessary personnel Monsanto A RME shall assess the workplace to determine if hazards are present or are likely to be present which necessitate the use of personal protective equipment PPE If such hazards are present or likely to be present the RME shall select and have each affected employee use the t
52. ny job site If there are any questions of ANY requirement do not hesitate to ask Any unanswered question could lead to devastating ends that could have been avoided All new employees will be trained by a RME prior to starting work The New Employee Safety Orientation Checklist shall be used by the RME as a reminder of the items that must be reviewed with the employee All items must be initialed or identified as not applicable The checklist must be signed by the employee and the RME after the orientation is complete This form will be kept in the employee s personnel file as a permanent record Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 NEW EMPLOYEE SAFETY ORIENTATION CHECKLIST RME must initial each item as you discuss it with the employee This checklist must be completed before the employee starts work Item Completed 1 Employee received Company Safety Manual 2 Review All chapters with employee and ask if they understand or have questions on any chapter 3 Instruct How to report unsafe conditions What to do in the event of an injury on the job State when and where safety tool box meetings are Hardhats work boots safety glasses goggles mandatory Personal protective equipment is not negotiable Proper lifting techniques and importance of back fitness 4 Other Please List I acknowledge that information on the above subjects was furnished to me during my ori
53. ollowing guiding principles Tri State s home office is the primary support for any subcontract activity All communication channels will be clearly defined before any work is to commence on any project site A clear scope of work with clear definitions on responsibilities and authorities will be defined before any work is to commence on any project site All budgeting working restrictions and quality requirements will be defined and agreed upon before any work can commence All payment terms and conditions will be clearly defined before work can commence Tri State will assign a primary RME to be responsible for all communication between the home office and the subcontractor for any and all communications unless otherwise assigned All subcontractors will be required to Be pre qualified before selection by strict review of their safety programs safety training documents and safety statistics Meet the safety metrics as defined TRIR EMR DART and Fatality Rates Attend pre job meetings kickoff meetings Attend complete any site specific safety training Complete documented weekly toolbox talks Complete documented job site safety analysis assessments Complete documented job safety inspections Be subject to post job safety performance reviews Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 28 0 PROCESS SAFETY MANAGEMENT Process Safety Management PSM A set of interrelated approaches to mana
54. ome in contact with electricity and how to prevent electricity from becoming a hazard while performing the task at hand Electricity is on every job site you will ever work on and is the most common hazard you will encounter By knowing the hazards involved with electricity you are greatly reducing the risks involved with working on every job site Electricity related hazards include electric shock and burns arc flash burns arc blast impacts and falls e Electric shock and burns An electric shock occurs when electric current passes through the body This can happen when touching an energized part If the electric current passes across the chest or head death can result At high voltages severe burns can result e Arc flash burns An electric arc flash can occur if a conductive object gets too close to a high amp current source or by equipment failure for instance while opening or closing disconnects The arc can heat the air to temperatures as high as 35 000 F and vaporize metal in the equipment The arc flash can cause severe skin burns by direct heat exposure and by igniting clothing e Arc blast impacts The heating of air and vaporization of metal creates a pressure wave that can damage hearing and cause memory loss from concussion and other injuries Flying metal parts are also a hazard e Falls Electric shocks and arc blasts can cause falls especially from ladders or unguarded scaffolding The following requirement
55. ools and exposed to the hazard of falling flying abrasive and splashing objects or exposed to harmful dust fumes mists vapors or gases shall be provided with particular PPE necessary to protect them from the hazard Review the following list of Task Tips to help you get started with every task assigned to you whether you are utilizing hand tools power tools or motorized machinery Review your work space to insure you are working in a safe clean and productive environment Review the tools needed hand tools and power tools to insure you have everything needed before you start the task assigned to you Complete the safety checklist for every power tool to be utilized for the task assigned to you as indicated on the Tool amp Equipment Checklist Make sure you have all necessary PPE to complete the task safely while utilizing the power tools required And finally measure twice and cut once This term doesn t just apply to material it also applies to making sure you have everything you need at hand before starting the task assigned to you 1 e material hand tools power tools cords proper lighting PPE etc Utilize the attached checklist Tool amp Equipment Checklist before you start your assigned tasks DEVELOP A TOOL amp EQUIPMENT CHECKLIST FOR USE ON JOBSITES Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 18 0 HAZARD COMMUNICATION HAZCOM Hazard Communication HAZCOM
56. ou are working on a site where emergency services are not provided and they are needed CALL 911 and report the accident Once the situation has been addressed by authorities police ambulance EMT etc call your direct supervisor and report the accident incident to them as soon as possible for immediate follow up If emergency services are not needed but care must be given A NON EMERGENCY take the individual to an approved location for care as needed see attached for approved medical provider locations If an approved location is not readily identifiable call human resources 800 386 8707 for identification of the closest care center to your location and then contact your direct supervisor for immediate follow up Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 6 0 RECORD KEEPING Record Keeping The maintenance of a history of one s training employment history disciplinary activity financial data and job history regarding types of projects and status of project completion It is Tri State s responsibility to oversee the appropriate record keeping process to maintain all employee documentation in strict accordance with the requirements of OSHA State of Iowa and the State of Illinois It is the employee s responsibility to report any training that was not obtained through Tri State to their direct supervisor to insure that all appropriate records are maintained as required Record keeping is
57. ound while working on any jobsite Proper notification will be given to the facility representative and corrective action will be taken to eliminate the hazard found Obtain hot work permits where required before any work can commence on any jobsite Immediately report incidents and near misses to your direct supervisor Adhere to any trade secret information and confidentiality of trade secret information as they apply where required Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 29 0 WELDING CUTTING AND HOT WORK Welding To join metals by applying heat sometimes with pressure and sometimes with an intermediate or filler metaling having a high melting point Cutting To separate into parts with sharp edged instruments or with highly abrasive materials that remove a section of the item separating it into pieces of itself Hot Work Riveting welding flame cutting or other fire or spark producing operation Spark Producing Tasks that when they are being completed have a high tendency of producing sparks It is Tri State s responsibility to train you on the equipment tools utilized when welding cutting and performing hot work tasks the proper protection to dawn when performing these tasks and how to protect others when performing these tasks It is every employee s responsibility to complete the training provided by Tri State and understand the policies and procedures set
58. pment to be used on any project site you are working on If you are asked to perform a task utilizing any equipment you are unfamiliar with or untrained on STOP WORK and notify your direct supervisor immediately so that training can be scheduled A pre use inspection of all aerial lifts is one of the most important steps in operating the equipment in a safe and efficient manner Take the time necessary to complete the equipment s pre use inspection checklist to insure that all components of the equipment are operating correctly and safely Review the equipment operators manual for clarification with this process ALWAYS Ensure that the equipment is properly fueled or charged for electric drive models Take time to inspect the area you are going to drive the aerial lift into to complete the task issued to you Ensure that there are no holes drop offs or oversized bumps and make sure that everyone working near you knows that you are in that area Ensure there is no debris that can puncture a tire or cause loss of traction Ensure that your equipment will be operated on ground appropriate for that particular equipment s ratings capabilities slope unleveled ground finished floors etc Be sure that the lift you are using is the best choice for the task you are completing There may be a better choice available Complete the pre use checklist included in the equipment manual Dawn and utilize proper fall protection Protection must be
59. r the specific noise environments in which the protector will be used Tri State will maintain all records for all employees for a minimum of 10 years Noise exposure noise pollution may not affect you immediately Prolonged exposure can have an everlasting and irreversible effect on your hearing PROTECT YOUR HEARING BY WEARING THE APPROPRIATE PPE Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 21 0 PERSONAL PROTECTIVE EQUIPMENT PPE Personal Protective Equipment PPE Clothing hard hats safety glasses goggles ear plugs fall protection devices steel toed shoes metatarsal guards and any other item designed to personally protect the wearer from harm that may occur during the process of completing a set task It is Tri State s responsibility to supply you with all necessary Personal Protective Equipment PPE training on the proper wear and care of it and to aid you in identifying when to properly dawn it It is every employee s responsibility to maintain their Personal Protective Equipment PPE be capable of identifying situations where PPE is required amp needed be capable of choosing the correct PPE to utilize wear it everywhere it is required and know when and how to dispose of expended PPE Hard hats gloves safety glasses goggles ear plugs Tyvec suits steel toe shoes fall protection harness lanyard and face shields are all examples of PPE that you may be required to wear and mai
60. ring is performed near combustible materials and or in locations where fire may develop Fire watchers shall have approved fire extinguishers available at all times during their watch Fire watch shall be maintained at least 30 minutes after any cutting or welding is completed Welding brazing soldering grinding band sawing and open flame torch cutting are all examples of hot work tasks and should all be addressed individually to ensure they are being completed in the safest manor possible for each and every location they are being performed Some tasks that you perform may not seem to be capable of producing sparks but they can Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 Hitting a fitting with a hammer to crack it can produce sparks Dropping metal parts on a concrete floor can create sparks As part of your self inspection you should be reviewing your surroundings prior to completing your task to insure that if sparks are produced they will not result in fire or explosions Dropping a fitting on the floor near a fuel storage tank can result in unwanted conditions NO TRI STATE EMPLOYEE IS AUTHORIZED TO COMPLETE ANY WELDING CUTTING OR HOT WORK TASKS THAT THEY HAVE NOT BEEN SPECIFICALLY TRAINED TO DO Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 30 0 STOP WORK Stop Work The authority and responsibility of every employee to stop work when an unsafe condition or act could result in an un
61. rules aoe Loose clothing and jewelry cannot be worn when operating machinery and equipment Proper work shoes shall be worn at all jobsites Open toed shoes and sneakers will not be permitted to be worn at any jobsite If you are observed wearing open toed shoes or sneakers you will not be permitted to work until you return with proper footwear Do not handle chemicals unless you have been trained in the safe handling procedure Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 15 Hardhats and eye protection shall be worn at all times 16 Read understand and follow the guidelines set forth in the material safety data sheets MSDS pertaining to your work 17 Compliance with safety and health rules and regulations is a condition of employment Any employee not following the requirements set forth in this manual will be subject to disciplinary actions as set forth herein Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 DEFINITIONS Tri State Automatic Sprinkler Inc Employer of the policy as herein described Also known in this manual as Tri State Competent Person One who is capable of identifying existing and predictable hazards in the surrounds or working conditions which are unsanitary hazardous or dangerous to employees and who has authorization to take prompt corrective measures to eliminate them Corporate Tri State Automatic Sprinkler Inc managing officers
62. ry employee no matter who is held to the same standards of performance as their fellow employee In other words everyone under the employment of Tri State Automatic Sprinkler Inc is required to follow all rules and regulations set forth in this or any other standard that they are performing work under All employees are expected to comply with jobsite rules and regulations and to follow established operating procedures set forth in this manual Violations will not be tolerated and any employee not following the requirements set forth herein will be held accountable for their actions Any act of any employee that results in the harm of another will be held accountable to the highest degree In the event a violation is observed the following procedures have been established to place an employee on notice Notice Action First Offense A written warning addressed to the employee and a copy placed in the employee s file referencing the violation and warning including date and time Second Offense A written warning addressed to the employee with reference to the violation including date and time of the occurrence A copy of this warning will be given to the employee the union shop steward and another copy will be placed in the employee s file Third Offense Termination of employment Within any consecutive 36 month period This policy is in effect unless there is a policy in our labor management agreement that supersedes the require
63. s It is every employee s responsibility to be able to identify the need for hearing protection and how to properly use it notify their direct supervisor of any potentially hazardous noise exposures that were previously unidentified and to properly care for and utilize hearing protection methods Every jobsite is different different trades working on different items at different phases of their particular work therefore it is never possible to know exactly what noise pollution you may be subject to If you ever suspect that you are being or may become exposed to excessive noise pollution contact your direct supervisor They will provide you with the appropriate hearing protection or eliminate the source all together if possible Training on Hearing Exposure Hearing Conservation will be provided at least annually and will be updated to be consistent with any changes in the PPE and work processes they may be asked to complete When any employee is subject to 85 decibels or greater for a 8 hour work period Tri State shall Supply all necessary hearing protection to all employees Develop and implement a monitoring program Implement an audiometric testing program Includes establishing a valid baseline audiogram to utilize as comparisons throughout the testing monitoring program Baseline audiogram shall be preceded by at least 14 hours of non exposure to workplace noise Establish a baseline audiogram for each employee withi
64. s apply to the use of cord and plug connected equipment and flexible cord sets extension cords e Extension cords may only be used to provide temporary power e Portable cord and plug connected equipment and extension cords must be visually inspected before use on any shift for external defects such as loose parts deformed and missing pins or damage to outer jacket or insulation and for possible internal damage such as pinched or crushed outer jacket Any defective cord or cord and plug connected equipment must be removed from service marked with the deficiency found and no person may use it until it is repaired and tested to ensure it is safe for use e Extension cords must be of the three wire type Extension cords and flexible cords must be designed for hard or extra hard usage for example types S ST and SO The rating or approval must be visible e Job made extension cords are forbidden e Personnel performing work on renovation or construction sites using extension cords or where work is performed in damp or wet locations must be provided and must use a ground fault circuit interrupter GFCI Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 e Portable equipment must be handled in a manner that will not cause damage Flexible electric cords connected to equipment may not be used for raising or lowering the equipment e Extension cords must be protected from damage Sharp corners and projections must be avoided Flexi
65. s not as likely to be found in paint and is banned from residential paint all together If lead is disturbed it can become airborne and enter the body through the lungs or digestive tract and into the blood stream where you can suffer from multiple symptoms that can lead to severe health problems If you suspect you have been exposed to lead and experience any of the following symptoms like headaches memory and concentration problems abdominal pain high blood pressure kidney damage sleep disturbances impotence muscle pain or digestive problems notify your direct supervisor immediately NO TRI STATE EMPLOYEE IS AUTHROIZED TO DISTURB LEAD CONTAINING MATERIALS FOR ANY REASON If you are working near or on any item that you suspect to contain lead stop work and notify your direct supervisor immediately Take precautions and be informed as to the hazards Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 13 0 ELECTRIC SAFETY Electricity A fundamental form of energy observable in positive and negative forms that occurs naturally as in lightning or is produced as in a generator and that is expressed in terms of the movement and interaction of electrons It is Tri State s responsibility to educate you when you on the hazards of electricity and how and where you may come in contact with electricity It is every employee s responsibility to be informed on the hazards of electricity know how and where you may c
66. se injury to you or one of your fellow workers Take the time to lock out tag out the system you are working on to ensure there is no accidental recharge while you have open pipes The following are examples of items that need to be locked out Fire Pumps power source and water source Jockey Pumps power source and water source Fire Pump Controllers power source and water source Jockey Pump Controllers power source and water source Wet Fire Sprinkler System water source Dry Fire Sprinkler System water source Deluge Fire Sprinkler System water source Interlocking Fire Sprinkler Systems water source Cranes power source Automated Paint Systems power source Ventilation Systems power source Lock out Tag out devices must indicate the identity and contact information of the employee placing the lock Periodic inspections of the energy control procedure shall be conducted and documented at least annually to ensure procedures and requirements are being followed Before an authorized or affected employee turns off a machine or equipment the authorized employee shall have knowledge of the type amp magnitude of the energy the hazards of the energy to be controlled amp the methods or means to control the energy All energy isolating devices that are needed to control the energy to the machine or equipment shall be physically located amp operated in such a manner as to isolate the machine or equipment from the energ
67. st aid that can make a lifetime of difference In the absence of medical assistance that is reasonably accessible in terms of time and distance to the worksite a person who has a valid certificate in first aid shall be available to render first aid If a qualified individual is required to be present onsite for medical assistance a certificate of training must be provided by either of the following U S Bureau of Mines the American Red Cross or equivalent training provider First aid kits shall be inspected after each use and quarterly to insure that all required materials are present as they were assigned to each vehicle as a kit First aid kits shall be kept readily available for all personnel to access in time of emergency need Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 First aid kits shall contain all necessary equipment and materials necessary to address potential emergency situations for the area you are working on Inventory and maintain your kits as required with this manual If the area you are working in does not contain appropriate eye wash stations and flushing stations notify your direct supervisor so that portable eye wash and flushing stations can be made available to everyone working on the jobsite for emergency purposes Stay alert stay alive Know your surroundings and who is working in them A few minutes of preparedness can make all the difference to you and your fellow employees Tri State
68. tact your project manager Conduct weekly safety toolbox meetings Make safety suggestions Serve on safety committee if requested Take an active part and participate in safety meetings Non compliance of these rules as well as other federal and or state laws or regulations may be legal violations subject to civil and or criminal penalties Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 10 11 12 13 14 EMPLOYEE RESPONSIBILITIES Whenever you are involved in an accident that results in personal injury or property damage no matter how slight the accident must be reported to your supervisor or other management personnel immediately Get first aid promptly Report any condition or practice you think might cause injury and or damage to equipment immediately to your supervisor Do not operate any equipment which in your opinion is not in a safe condition Report immediately the condition that you believe is unsafe to your foreman All prescribed safety equipment and personal protective equipment must be used when required and must be maintained in good working condition Itis your personal responsibility to use such equipment The use of required personal protective equipment is non negotiable Obey all safety rules government regulations signs markings and instructions Be particularly familiar with the rules and regulations that apply directly to you in the area in which you work If you don t know
69. tilized for their intended purpose 2 Ladder Inspection Always check a ladder before using it Check all ladders to see that steps or rungs are tight secure and spaced to meet OSHA standards requirements Be sure that all hardware and fittings are properly and securely attached Test movable parts to see that they operate without binding or without too much free play Inspect metal and fiberglass ladders for bends and breaks Never use a damaged ladder Tag it Defective and report it to your direct supervisor so that it may be removed from the job and replaced immediately Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 At a minimum ladders must be inspected and tagged annually by qualified trained personnel 3 Ladder Setup Place ladder feet firmly and evenly on the ground or floor Make sure the ladder is sitting straight and secure before climbing it If one foot sits in a low spot build up the surface with firm material Ensure that the ladder is extended at a minimum of 36 above the upper landing of the landing surface or work space Do not try to make a ladder reach farther by setting it on boxes barrels bricks blocks or other unstable bases Do not allow ladders to lean sideways Level them before using Brace the foot of the ladder with stakes or place stout boards against the feet if there is any danger of slipping Never set up or use a ladder in a high wind especially a lightweight metal or fiber
70. to employees with regard to fire hazards to which they may be exposed Fire Extinguishers All employees must be trained on the set up and use of fire extinguishers to be used on any jobsite This training will be completed before assignment to any jobsite and be completed annually for the entirety of your employment Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 Extinguishers must be kept clean and dry at all times Extinguishers must be visually inspected monthly Annual inspection and testing will be completed on all extinguishers by a qualified individual Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 16 0 BASIC FIRST AID Basic First Aid Emergency aid or treatment given to someone injured suddenly ill etc before regular medical services arrive or can be reached It is Tri State s responsibility to give you the tools necessary to aid someone who may be in need of basic first aid It is the employee s responsibility to react when required to administer basic first to their fellow workers no matter who they are This chapter serves as a guideline for all employees to use to aid them in being as prepared as they can be for any emergency or situation that may occur that requires the need for you to administer basic first aid These steps will aid you to insure that you are as prepared as you can be on every jobsite Familiarize yourself with the facility layout so you will know what to do
71. trolled products to train all employees on how to interpret the MSDS forms and that all employees have easy access to that data at all times It is every employee s responsibility to know what controlled product they are handling how to read the MSDS forms and where to get them at all times Some of the materials you are required to work with on jobsites may hazardous to your health if you come in direct contact with them The MSDS forms required to be maintained on the controlled products on your jobsite are found by logging into the employee portal found www tri statesprinkler com If you or anyone ever have any questions regarding these forms please contact your direct supervisor EVERYONE WORKING WITH OR AT TRI STATE AUTOMATIC SPRINKLER INC HAS THE RIGHT TO KNOW THE HAZARDS OF THE CONTROLLED PRODUCTS THEY ARE WORKING WITH IF YOU EVER HAVE ANY QUESTIONS REGARDING THESE HAZARDS CONTACT YOUR DIRECT SUPERVISOR FOR CLARIFICATION Tri State Automatic Sprinkler Inc SM 2013 May 15 2013
72. ur life NO TRI STATE EMPLOYEE IS AUTHROIZED TO WORK ON ANY LINES OR TANKS CONTAINING ANY COCNETRATIONS OF AMMONIA FOR ANY REASON If you are working near lines or tanks that are marked to contain Ammonia take precautions and be informed as to the hazards Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 11 0 ASBESTOS AWARENESS Asbestos Is a naturally occurring fibrous silicate mineral that is mined from seams in rocks Asbestos can appear in fibrous crystal form and when crushed separates into flexible airborne fibers It is Tri State s responsibility to educate you when you may be required to work on job sites that are known to contain asbestos and to the effects of direct contact with asbestos It is every employee s responsibility to watch out for asbestos and any items you suspect to contain asbestos and to report any suspected contact you have with asbestos Asbestos is commonly used as a heat and coolant insulator and can be found in many materials from floor tiles ceiling tiles roofing sheets to piping insulation and brake pads In its dormant state most asbestos is not harmful however when disturbed asbestos can become airborne and can enter into the body through the nose and mouth resulting in severe health hazards like Asbestosis Hardening of the lungs Mesothelioma A lung cancer of the lining of the chest or abdominal cavity Lung Cancer Usually begins as a lung tumor in the lower lungs w
73. ut to the project foreman when they turn in their timesheets each week Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 8 0 SELF INSPECTION Self Inspection An inwardly object inspection of your individual abilities to complete the task at hand in a safe and hazard free manor that will result in the task being completed as it was planned It is the responsibility to Tri State to provide an adequate definition to aid you in completing a self inspection before each and every task is completed It is the responsibility to every employee working on every job site to complete a self inspection before starting any task at hand to ensure that it can be completed in a safe and hazard free manor Start your day in a Safe Working Environment Self inspections are not necessarily a formal inspection It can be a simple as a mental check list to ensure you have everything you need to complete the task at hand 1 e proper hand tools adequate lighting a secure working platform the correct materials and all necessary PPE and it can be as complicated as a formal walk through with the general contractor or AHJ to insure that there are no other trades working under your area and all necessary precautions have been taken to ensure there is no risk of injury to life or property on any level It is our policy to eliminate hazard exposures that can lead to employee injury or property damage Self inspection is one way to complet
74. y source Prior to starting work on machines or equipment that have been locked or tagged out the authorized employee shall verify that isolation amp de energize of the machine or equipment have been accomplished Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 When servicing and or maintenance is performed by a crew craft department or other group they shall utilize a procedure which affords the employees a level of protection equivalent to that provided by the implementation of a personal lockout or tag out device Group lock out tag out procedures shall be completed in strict accordance with the guidelines as set forth in OSHA 1910 147 The project foreman is responsible for all employees that will be working on all equipment locked out tagged out for the duration of all employees scheduled shifts Once all employees have been verified to have removed their locks tags then responsibility will fall upon the next shifts project foreman if any is required Training will be completed prior to any employee performing work on any project Retraining will be completed annually when there is a change in job assignment machines equipment a new hazard is introduced to the project or when there I s a change in energy control procedures By ensuring that the system device and potential machinery that you are working on is locked out and that all necessary personnel have been notified of your intentions of work you are ensuring th
75. ypes of PPE that will protect the affected employee from hazards identified in the hazard assessment and communicate those decisions to all employees working on that project The following is a list of PPE required on every jobsite Hard hat Eye protection Hearing protection Steel toed shoes The following is a list of PPE that may be required as needed required by AHJ Long sleeves 100 cotton clothing High visibility clothing Goggles Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 Tyvec suites Fall protection harness lanyard Metatarsals Any employee not wearing the minimum required PPE is subject to disciplinary action as listed herein IT IS TRI STATE S POLICY FOR EVERY EMPLOYEE TO UTILIZE THE PPE SUPPLIED TO THEM ON EVERY JOBISTE Tri State Automatic Sprinkler Inc SM 2013 May 15 2013 22 0 SCAFFOLDING Scaffolding A temporary structure or platform either supported from below or suspended from above on which workers sit or stand when performing tasks as specific heights above the ground It is Tri State s responsibility to supply adequate platforms for every employee to utilize while completing the tasks given to them and to train them on pre use inspections of those platforms It is every employee s responsibility to be familiar with the requirements of scaffolding platforms and to utilize the platforms provided to them to complete the tasks given to them in a safe and efficie

Download Pdf Manuals

Related Search

Related Contents

Tecumseh VSA9521ZXT Performance Data Sheet  Dicota D30672  User manual M2  Mode d`emploi - Nintendo of Europe  Billion Electric Company 5200S User's Manual  N272399 man recip saw DW304 Euro.indd  Un concentré de technologie pour le voyage Spécifications  

Copyright © All rights reserved. Failed to retrieve file