Billion Electric Company 5200S User's Manual
Contents
1. PPPoE Lit when tl e Lit when successfully system is ready connected to an ADSL DSLAM connection Attention BIPAC 5200S has not supported the ON OFF switch The Rear Ports Connect your Connect the computer to a LAN supplied power port using the adapter to this included Ethernet jack cable i lal i Press it to reset the device or restore to factory default settings Connect the supplied RJ 11 cable to this port when connecting to the ADSL telephone network Billion BiPAC 5200 Series ADSL2 Firewall Router Hardware Connection BiPAC 5200G 5200GR2 5200GR3 5200GR4 5200GR5 Power wl ESET God Adapter Switching HUB rro Phone Cable Ethernet Cable ay vu A s P ip Ethernet Cable ee Ethernet Cable 7 Ethernet Cable Phone Cable BiPAC 5200 5200R3 Power Adapter Phone Cable Switching HUB Ethernet Cable ig Ethernet Cable Tal lp Ethernet Cable en hy ie BiPAC 5200S 5200SA2 5200SA3 i Power Adapter Lii A Phone Cable lg Ethernet Cable g EN Y ia Quick Start Guide Hardware Installation 1 Power Connection Plug the supplied power adapter to the wall jack and the other side to the router Please note that the plug type may differ according to different countries 2 LAN Connection2. BiPAC 5200 Series 802 11g ADSL2 Firewall Router Quick Start Guide Billion BiPAC 5200 Series ADSL2 Firewall Router PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE IF YOU NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION PLEASE REFER TO THE USER S MANUAL ON THE CD ROM Package Contents BiPAC 5200 Series ADSL2 Router CD containing the on line manual RJ 11 ADSL telephone cable Ethernet CAT 5 LAN cable AC DC power adapter 12VDC 1A for 5200 5200R3 5200G AC AC power adapter 12V AC 1A for 5200S 5200SR2 5200SR3 5200GR2 5200GR3 5200GR4 5200GR5 This Quick Start Guide Splitter Micro filter Option Power Adapter The type may differ by different country e Do not use the router in high humidity or high temperatures e Do not use the same power source for the router as other equipment e Do not open or repair the case yourself If the router is too hot turn off the power immediately and have it repaired at a qualified Warning service center e Avoid using this product and all accessories outdoors Place the router on a stable surface e Only use the power adapter that comes with the package Using a Attention different voltage rating power adaptor may damage the router Quick Start Guide Hardware Overview BiPAC 5200G 5200GR2 5200GR3 5200GR4 5200GR5 L
3. Connect the supplied RJ 45 Ethernet cable to one of the Ethernet ports and the other side to the PC s Ethernet interface LAN Connection 3 TT 3 ADSL Connection Connect the supplied RJ 11 phone cable to the router s ADSL port and the other side to the phone jack on the wall ADSL Connection ADSL on Splitter Phone jack Billion BiPAC 5200 Series ADSL2 Firewall Router 4 Splitter Micro filter Connection splitter Micro filter are important for ADSL installation High frequency signals are directed to the ADSL modem and low frequency signals are directed to the telephone or other analog voice channel device to prevent inter modulation distortion and also to get good speed and stable ADSL sync rate a Splitter connection If the installation has only a single telephone and a single ADSL modem then a splitter can be employed Splitter POTS ADSL b Micro filter connection If the installation has several telephones or other analog devices then an internal micro filter can be employed at each analog device FAX icro filter POTS ADSL Setup Utility After you complete the hardware installation insert the CD ROM to the CD ROM drive to perform the Setup Utility for network configuration The Setup Utility will auto run Follow the step by step configuration wizard the utility will guide you to complete the basic network configuration Quick Start Guide Troubleshooting 1
4. None of the LEDs are on when you turn on the router Check the connection between the adapter and the router If the error persists you may have a hardware problem In this case you should contact technical support You have forgotten your router login and or password Try the default login and password please refer to Chapter 3 If this fails you can restore your router to its factory settings by holding the Reset button on the back of your router for 6 seconds or more Can t ping any PCs on the LAN Check the Ethernet LEDs on the front panel The LED should be on for a port that has a PC connected If it is off check the cables between your router and the PC Make sure you have uninstalled any software firewall for troubleshooting Verify that the IP address and the subnet mask are consistent between the router and the workstations Frequent loss of ADSL linesync disconnections Ensure that all other devices connected to the same telephone line as your router e g telephones fax machines analogue modems have a line filter connected between them and the wall socket unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician and ensure that all line filters are correctly installed and the right way around Missing line filters or line filters installed the wrong way around can cause problems with your ADSL connection including causing frequent disconnections If you have a back to base
5. alarm system you should contact your security provider for a technician to make any necessary changes Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User s Manual If you cannot resolve the problem with the Troubleshooting chapter please contact the dealer where you purchased this product Contact Billion WORLDWIDE http www billion com
6. it when successfully Lit green when the Lit when power is ON wireless connection SLA eae a ci is established egy ores The Front LEDs Lit when the Lit when connected to Lit steady when there system is ready an Ethernet device is a PPPoA PPPoE connection The Rear Ports Connect your Connect the computer to a LAN Connect the supplied detachable antenna port using the power adapter to this included Ethernet jack _ tn Press it to reset Power Connect the supplied the device or ON OFF RJ 11 cable to this restore to factory switch port when connecting to the ADSL telephone network default settings Billion BiPAC 5200 Series ADSL2 Firewall Router BiPAC 5200 5200R3 The Front LEDs Lit steady when Lit when connected there is a PPPoA to an Ethernet PPPoE device Lit when power is ON Lit when the Lit when successfully system is ready connected to an ADSL DSLAM connection The Rear Ports Connect the Connect your supplied power computer to a LAN adapter to this port using the jack included Ethernet cable Cra Press it to reset the device or restore to factory default settings Connect the supplied RJ 11 cable to this port when connecting to the ADSL telephone network Quick Start Guide BiPAC 5200S 5200SR2 5200SR3 The Front LEDs Lit when Lit when connected to an Lit steady when power is ON Ethernet device there is a PPPoA
Download Pdf Manuals
Related Search