- Sensory Software
Contents
1. LC key LockCode af tee Home picomed local Gewa a Channel m Learn Individual key Choose key _ Learn a A E On Off LC key Common code Picomed Gewa Continuos IR On Off Delete IR Delete IR on key Versions T LockCode page 2 page1i On Off f j Spasm filter Product Settings On Off j i e General settings _ Product status Battery Info compatibility Backup restore Backup Restore Info versions Product firmware Info licenses Load file IR transmitters Pico4 Pico8 and Picol6 Sound at keypress On Off Time setting Value Sound when scanning On Off sce Be Interval Number of rounds Value Factory setting Reset all settings Value Page 42. goto www picomed no e Choose Products IR transmitters Pico4 8 16 and follow instructions on screen Then e Connect USB cable between computer and I R remote open a web browser and go to picomed local IR transmitters Pico4 Pico8 and Picol6 Page 2 X4 PICOMED Programming on IR transmitters Without a web browser it is possible to copy IR signals into it and to enable disable commoncode oe a a sh CE ZS Enter programming mode press and hold keys 1 2 and 3 for 3 seconds gt long beep Leave programming mode press and hold key 1 for 3 seconds or wait for timeout after 60 sec without any keystrokes If low battery red flashing light for 2 seconds then it leaves programming mode To enable disable commoncode press and hold lock code key for 3 seconds Commoncode off a short signal from beeper light in lock code key and the green light Commoncode on a long signal from beeper light in lock code key and the green light Norwegian version transmits IR Picomed usercode 1 channel 1 also named NAI 1 Swedish version transmits IR Gewa channel 16 Copying IR signals into Picomed IR transmitters Position Pico4 8 16 and the other R transmitter against each other Press shortly on the actual key on Pico4 8 16 steady green light in actual key Press shortly on actual key on the other R remote it transmits IR to Pico4 8 16 When IR is received by Pico4 8 16 it will respond with single gr
3. X PICOMED User manual Pico4 Pico8 og Pico16 short version Revisionlist Introduction This is a short version of the user manual for Picomeds IR transmitters Pico4 Pico8 and Picol6 For more information please use the complete user manual Overview The IR transmitters have 4 8 and 18 buttons and 2 pages Functions Learnable R signals Built in IR signals Scanning 1 switch Integrated fingerguide Possible to choose continious IR signals or not when press amp hold on keys Programmable sound on keypress spasm filter parameters for scanning backup The figure shows an overview of a Pico4 Pico and Picol6 have the same functions If page 2 is be enabled the Pico4 and Pico8 use the lower left key as a page select key In this case it will not transmit any IR signals Pico4 will have a maximum of 6 channels and Pico8 will have a maximum of 14 channels if page 2 is enabled Picol6 has a dedicated page select key Lock code key transmits R signals in the same way as the other keys It is also able to transmit lock code and common code It may be programmed as a page independent key The battery is rechargeable and it will normally not be necessary to exchange it e Low battery red light indicator flashes for 2 seconds when it transmits IR signals e Charging green light flashes slowly It has a steady green light when it is full charged e Typical time of charging for an empty battery is 4 5 hour
4. een flashing Press once again shortly on actual key on the other R remote A successful IR learning will be indicated by 3 green flashing then light is turned off Go back to step 2 to copy an IR signal to an other key Leave programming mode when finished IR learning will be interrupted after 20 seconds if no IR is received It will then go to ordinary programming mode To switch to page 2 in programming mode press and hold page select key for 3 seconds IR transmitters Pico4 Pico8 and Picol6 Page 3 Programming map UserCode Channel Picomed _ 2a Preset doorphone IR signal Preset phone X PICOMED Gewa Channel Learn Learn copy IR Se ee a Continuos IR On Off Delete IR Delete all IR ee ee UserCode Keys on page 1 f Picomed Channel LC key LockCode G Channel Nor _ LC key LockCode IR signal or Learn Individual key Choose key Learn copy IR SS FO On Off LC key Common code Picomed Gewa Continuos IR On Off Delete IR Delete IR on key On Off UserCode 4 Channel icomed _ eS Preset doorphone IR signal Preset phone Gewa Channel Learn aA Learn j ot H E e Pico4 8 16 Prg5 Continuos IR On Off A ee Delete IR Delete all IR UserCode Keys on page 2 anes All pages Stee _Picomed Channel
5. s Gjerstadveien 398 N 4993 Sundebru Ph 47 37119950 Fax 47 37119951 E mail post picomed no VAT no 962 211 631 MVA X PICOMED Programming on screen Charging i Charging cable Android products uses an app downloaded from Google play Search for Picomed and install the app Picomed Starter ssp adapter cable OTG e Connect the OTG cable to Picomeds IR transmitter and the USB cable to your unit When a USB icon is shown on screen Open the Picomed Starter app choose Enable Connection and enable USB internet sharing go one step backward in the app on your unit e Choose Configure Product The app will download a web page from Pico4 8 16 Apple products will work without any installation on iPhone 4 or newer and for iPad 3 or newer which has a SIM card holder e You have to turn on mobile data on the unit to let it use the USB cable for downloading an internet page from the Picomed transmitters Tap Settings Cellular Cellular data on If this alternative is not available it may be that your unit or your mobile supplier not has this option e Connect the OTG cable to Picomeds R transmitter and the USB cable to your unit Then go to this adress in browser picomed local Windows PC has to install a driver the first time you are going to use it Download the driver from Picomeds web site It may be different drivers for different Windows versions e Use a web browser and
Download Pdf Manuals
Related Search