Home

DIADEMA ACS IDRO USER MANUAL - La Nordica

1. MENU STRUCTURE amp GO BACK EXIT D 2 3 PARAMETER SCROLLING NEXT 2 PREVIOUS 3 45 MODIFY SETTINGS DATA INCREASE 4 DECREASE 5 6 CONFIRM ACCESS MENU gt MENU TEXT VALUE FUNCTION SET POWER POWER 01 05 Selecting the power SET H20 65 80 C Selection of the boiler temperature set point SET BOILER MAX CANNOT ACTIVATED SET TEMPERATURE SET BOILER MIN s CANNOT BE ACTIVATED SET PUFFER MAX 50 78 C Maximum Puffer set selection SET PUFFER MIN 45 65 C Minimum Puffer set selection BURN POT CLEANING 0 50 Burn pot automatic cleaning frequency adjustment STAND BY OFF ON Activation or deactivation of the stand by function ENABLE CHRONO ON OFF Activation deactivation of the weekly programmer PELLETS 30 20 Selectingthe percentage of pellet feed SET ADJUSTMENTS SUMMER BEN SEASON WINTER Season and priority selection see specification ENABLE BOILER TIMER ON OFF CANNOT BE ACTIVATED BIOMASS BOILER SETTING BIOMASS AUX Boiler mode selection AUX STATUS STOVE STATUS References reserved to the technician DAY MON SUN Setting the day of the week HOURS 00 24 Adjustment of the hour SET MINUTES 00 59 Adjustment of the minutes CLOCK DATE 1 31 Adjustment of the date MONTH 1 12 Adjustment ofthe month YEAR 00 99 Adjustment ofthe year
2. QExtraflame ENGLISH SET POWER The following menu allows to set the power Minimum power 1 maximum power 5 CONTROLS PROCEDURE Press key 6 and SET POWER will appear Confirm using key 6 ThePOWER will be displayed Press4to increase the setting and 5 to decrease it Press key 6 to confirm and key 1 to return to the previous menus up to the initial status SET TEMPERATURE The following menu allows the boiler temperature to be set The possible settings are 65 80 C CONTROLS PROCEDURE Press key 6 and SET POWER will appear Press key 2 several times until SET TEMPERATURE is displayed Confirm using key 6 Press 4 to increase the setting and 5 to decrease it Press key to confirm and key 1 to return to the previous menus up to the initial status v9 gt SET BOILER TEMPERATURE CANNOT BE ACTIVATED N B DIADEMA ACS FEATURES AN INSTANTANEOUS HEAT EXCHANGER FOR THE PRODUCTION OF DOMESTIC HOT WATER AND IT IS NOT POSSIBLE TO SET THE BOILER TEMPERATURE SET PUFFER TEMPERATURE N B the screen is not displayed if the puffer is disabled CONTROLS PROCEDURE Presskey6 Press key 2 until SET TEMPERATURE is displayed Confirm using key 6 Press key 2 until SET PUFFER MAX is displayed adjust using keys 4 5 Press key 2 until SET PUFFER MIN is displayed adjust using keys 4 5 Press key 6 to confirm press key 1 several times to exit the menu of 6 SET
3. C o A o O o O A ss 40 WARRANTY CONDITIONS 41 Extraflame ENGLISH WARNINGS This instructions manual is an integral part of the product make sure that it always accompanies the appliance even if transferred to another owner or user or if transferred to another place If it is damaged or lost reguest another copy from the area technician This product is intended for the use for which it has been expressly designed The manufacturer is exempt from any liability contractual and extracontractual for injury damage caused to persons animals and objects due to installation adjustment and maintenance errors and improper use Installation must be performed by gualified staff which assumes complete responsibility for the definitive installation and conseguent good functioning of the product installed One must also bear in mind all laws and national regional provincial and town council Standards present in the country in which the appliance has been installed Extraflame S p A cannot be held responsible for the failure to comply with such precautions After removing the packaging ensure that the content is intact and complete Otherwise contact the dealer where the appliance was purchased All electric components that make up the product must be replaced with o
4. UNI EN 1457 2012 chimneys clay ceramic flue liners UNI TS 11278 2008 Metal chimneys flue liners flue ducts UNI 7129 point 4 3 3 Fire Brigade provisions local rules and regulations NATIONAL REGIONAL PROVINCIAL AND TOWN COUNCIL REGULATIONS One must also bear in mind all laws and national regional provincial and town council Standards present in the country in which the appliance has been installed ENGLISH TERMS AND DEFINITIONS Aeration Air renewal is required both for the disposal of the combustion products and to prevent mixtures with a hazardous content of non combusted gases Closed hearth appliance Appliance designed for operation with closed combustion chamber Forced draught appliance Appliance with ventilation in the fumes circuit and combustion with fumes flow at a positive pressure with respect to the environment Chimney Structure consisting in one or several walls containing one or several outflow airways The purpose of this predominantly vertical element is to expel the combustion products at a convenient height from the ground Smoke duct Component or components that connect the outlet of the heat generator to the chimney Chimney cap Device that placed on the chimney outlet allows the dispersion of the combustion products even in presence of adverse weather conditions Condensation Liquid products which form when the fumes temperature is lower or equal to the water dew point
5. 4 DECREASE 5 La SET POWER y gt SETTEMPERATURE 6 h SETH2O SET ADJUSTMENTS BURN POT CLEANING SET BOILER MAX STATUS X6 stovestatuS STAND BY SET BOILER MIN BOILER STATUS ENABLE CHRONO SET PUFFER MAX HEAT STATUS PELLETS SET PUFFER MIN PUFFER STATUS SUMMER WINTER y ENABLE DISABLE BOILER CHRONO y BIOMASS BIOMASS AUX AUX USER MENU SETCLOCK SET CHRONO TECHNIC SET RESERVED TO THE QUALIFIED LANGUAGE TECHNICIAN DISPLAY KEY LOCK BRIGHTNESS dj RESET BOILER CHRONO BASIC INSTRUCTIONS Before lighting the stove the following points must be The following recommendations must be followed the first verified times the stove is ignited o The hydraulic system must be completed in compliance smells may be produced due to the drying of the with the guidelines of the regulations and the manual paints and silicones used Do not remain in the environment tank must be full of pellets for long periods The combustion chamber must be clean Do not touch the surfaces as they could still be The burn pot must be completely free and clean unstable _ Check the hermetic closure of the fire door and the ash _ Air the room well several times drawer hardening of the
6. as well as these instructions For Italy installation must be carried out by professionally authorised staff Ministerial Decree dated 22 01 08 n 37 Extraflame S p A declines all liability for damage injury to objects persons caused by the plant SAFETY DEVICES FOR CLOSED VESSEL SYSTEM According to Standard UNI 10412 2 2009 in force in Italy closed systems must be equipped with safety valve pump control thermostat acoustic alarm activation thermostat temperature indicator pressure indicator acoustic alarm regulation automatic circuit breaker switch automatic circuit breaker block switch block thermostat circulation system expansion system safety dissipation system incorporated with the generator with thermal safety valve self activated whenever the appliance does not have a temperature self adjustment system DISTANCES OF SAFETY DEVICES ACCORDING TO THE STANDARD The temperature safety sensors must be fitted on the machine at a distance no greater than 30 cm from the flow connection Whenever the generators lack a device those missing can be installed on the generator flow pipe within a distance no greater than 1 m from the machine QExtraflame ENGLISH COMPONENT DISTANCE Temperature safety sensors On the machine or not exceeding 30 cm Missing devices because not standard Not exceeding one metre on the flow pipe Domestic or automatic feed heating appliances must be equipped with a fuel block th
7. ADJUSTMENTS continues on next page QExtraflame ENGLISH BURN POT CLEANING The menu allows to increase the frequency of the automatic burn pot cleaning CONTROLS PROCEDURE Press key 6 and SET POWER will appear Press key 2 several times until SET ADJUSTMENTS is displayed Confirm using key 6 BURN POT CLEANING will appear To increase the automatic cleaning frequency press 4 To go back to standard values 00 decrease by pressing 5 Press key 6 to confirm and key 1 to return to the previous menus up to the initial status vr 9199 STAND BY The Stby function is used if immediate stove switch off or modulation via an additional thermostat is desired CONTROLS PROCEDURE Press key 6 and SET POWER will appear Press key 2 several times until SET ADJUSTMENTS is displayed Press key 6 Pa STAND BY will appear O Use keys 4 5 to select enable ON disable OFF Press key 6 to confirm and key 1 to return to the previous menus up to the initial status ENABLE CHRONO The boiler chrono can be enables disables from this menu CONTROLS PROCEDURE Press key 6 and SET POWER will appear Press key 2 several times until SET ADJUSTMENTS is displayed Press key 6 Press key 2 until ENABLE CHRONO is displayed Use keys 4 5 to enable ON disable OFF Press key 6 to confirm and key 1 to return to the previous menus up to the initial status PELLET ADJUSTMENT Th
8. Ducting pipe Pipe made up of one or several predominantly vertical elements specifically suitable for collecting and expelling the fumes as well as to withstand the relative components and any condensate over time suitable to be installed in a chimney existing or new technical compartment even in new buildings Sealed installation Installation of an appliance with sealed operation so that all the air required for combustion is taken from outside Maintenance Set of procedures required to ensure and maintain safety and functionality over time and maintain the efficiency of the system within the prescribed parameters Chimney system Chimney installed using a combination of compatible components manufactured or specified by a sole manufacturer whose product liability covers the entire chimney Fumes exhaust system Flue gas exhaust system independent from the appliance made up of a smoke duct chimney or individual flue and chimney cap Radiation area Area immediately in front of the hearth in which the radiant heat caused by combustion is diffused Reflux area Area beyond the extrados of the roof in which overpressure or depressions occur which may affect the proper discharge of the combustion products QExtraflame ENGLISH FUNCTIONAL OPERATIONS DIAGRAM State of the art installation and proper system operation include a series of activities 1 Preliminary activities verification of the suitability of the insta
9. ENABLE CHRONO OFF Activation deactivation of the weekly programmer START PRG1 OFF 00 00 Time 1 ignition STOP PRG1 OFF 00 00 Time 1 switch off MONDAY PRG1 OFF si SUNDAY PRG1 OFF ON OFF Ignition switch off consents for various days SET PRG1 65 80 C Temperature setting for the 1 time span START PRG2 00 10 OFF 00 00 Time 2 ignition STOP PRG2 00 10 OFF 00 00 Time 2 switch off MONDAY PRG2 OFF RI a d SUNDAY PRG2 OFF ON OFF Ignition switch off consents for various days USER MENU CHRONO SET PRG2 65 80 C setting roon temperature for the 2 time slot START PRG3 00 10 OFF 00 00 Time 3 ignition STOP PRG3 00 10 OFF 00 00 Time 3 switch off ne PRES OEE me ilmi Ignition switch off consents for various days SET PRG3 65 80 C Setting room temperature for the 3 time slot START PRG4 00 10 OFF 00 00 Time 4 ignition STOP PRG4 00 10 OFF 00 00 Time 4 switch off an PRGFOFF SUNDAY PRGA ON OFF Ignition switch off consents for various days SET PRG4 65 80 C Setting room temperature for the 4 time slot LANGUAGE ITAL ENGL DEUT FRAN ESPA Selecting the language DISPLAY KEY LOCK ON OFF Key lock function activation disabling BRIGHTNESS OFF 10 31 Selecting the display brightness RESET RESET ON OFF Resets the values modifiable by the user back to the default values BOILER BOILER CHRONO OFF 00 00 Boiler weekly programmer CANNOT BE ACTIVATED
10. appliance to the chimney is not allowed ro id ia SK TT 4 ff fF fa Correct 4 F 7 7 rel L OK bid OK Extraflame counter slope sections are not allowed thesmoke ducts must have along their entire length a diameter that is no less than that of the attachment of the appliance exhaust pipe any section changes are allowed only on the inlet to the chimney they must be installed so as to limit the formation of condensation and prevent their release from the joints they must be positioned at a distance no less than that indicated in the product specifications from combustible materials the smoke channel duct must allow to collect the soot and to be cleaned using a swab and inspected after being disassembled or through inspection openings when not accessible from inside the appliance ENGLISH ADDITIONAL REQUIREMENTS FOR APPLIANCES FITTED WITH AN ELECTRIC FAN FOR FUMES EXPULSION For the heat generator appliances equipped with electric fan for expelling fumes the instructions below must be followed The horizontal sections must have a minimum upward slope of 3 The length of the horizontal section must be minimal and in any case no longer than 3 metres The number of direction changes including the one due to the use of the
11. in order to prevent the chimney from resting on the appliance It is forbidden to have other air supply channels and pipes for plant engineering transit inside the fumes exhaust systems especially if over sized The components of the fumes exhaust system must be chosen in relation to the type of appliance to be installed in compliance with inthe event of metal chimneys UNI TS 11278 with particular attention to what is stated in the specification the event of non metallic chimneys UNI EN 13063 1 and UNI EN 13063 2 UNI EN 1457 UNI EN 1806 considering especially temperature class pressure class fumes seal at least equal to the seal required for the appliance moisture resistance resistance to condensation class or level of corrosion and specification of the materials constituting the inner wall in contact with the fumes soot fire resistance class minimum distance from combustible materials The installer of the fumes exhaust system once the installation is complete and the relevant checks and inspections have been made must fix the chimney plaque supplied by the manufacturer with the product in a visible manner near the fireplace and which must be completed with the following information QExtraflame ENGLISH nominal diameter distance from combustible materials indicated in millimetres followed by the arrow and flame symbol installer data and date of installation Every time one mu
12. key 6 1ST TIME SLOT H20 TEMPERATURE SETTING Press key 6 to confirm and continue programming START PRG1 Using buttons 4 5 select the desired SET PRG1 OFF H20 temperature 75 C START PRG1 OFF appears 65 80 C To confirm and proceed press key 6 1ST TIME SLOT SWITCH ON 2ND TIME SLOT SWITCH ON Use keys 4 5 to enter the time 08 00 At this point the second time slot must which corresponds to the switch on START PRG be programmed START PRG2 time of the 1st time slot 08 00 OFF To confirm and continue programming press button 6 Press button 3 to go back to the previous parameter The sequence to be followed is the same and is repeated as for the 1ST TIME SLOT switch on QExtraflame ENGLISH 2ND TIME SLOT SWITCH ON At this point the second time slot must be programmed The sequence to be followed is the same and is repeated as per the 1ST TIME SLOT SWITCH ON On this occasion it is only necessary to enter the time for example start at 15 00 and Stop at 22 00 and to activate the days Saturday and Sunday by setting them at ON RECOMMENDATIONS EXAMPLE The ignition and switch off times must be within the arc of Switch on time 07 00 CORRECT one day from 0 to 24 and not over several days R Before using the chrono function set the current day and time Therefore check that the points listed in the Set clock sub chapter have been followed so that the chrono function Sich ontme2200
13. this key The key allows the user to exit any program or display and returns to the main menu without saving the data The key returns to the display ofthe various menus This key confirms the adjustments made during the user menu programming phase The key moves forward in the various menus Pre set key for future applications The key decreases the value to be set 1 ON OFF 2 POWERINCREASE 3 POWERDECREASE 4 T INCREASE 5 T DECREASE 6 ENABLE DISABLE CHRONO 7 ENABLE DELAYED SWITCH OFF 8 MENU 9 INCREASE 10 ESCKEY 11 BACK 12 CONFIRMATION KEY 13 FORWARD 14 ENABLE F1 FUNCTION 15 DECREASE 16 STOVE STATUS Pressing this key will display the general status of the stove Important note the numbers shown on the remote control are purely indicative and are not present on the remote control supplied with the product TYPE AND REPLACEMENT OF BATTERIES The batteries are housed in the lower part of the remote control To replace them remove the battery holder as indicated in the figure at the back of the remote control remove or insert the battery according to the symbol on the remote control and on the battery itself For operation 1 CR2025 3V lithium buffer battery is required The batteries used contain metals harmful for the environment They must therefore be disposed of separately in appropriate containers IF THE REMOTE CONTR
14. used For further details refer to the cleaning and maintenance chapter Inspection and maintenance report At the end of the inspection and or maintenance operations a report must be issued and released to the owner or person acting for him who must confirm its receipt in writing The report must indicate the situations encountered the action taken any components replaced or installed and any comments recommendations and requirements The report must be kept with the relative documentation In the inspection and maintenance report one must mention anomalies detected that cannot be removed which pose a risk to the safety of the user or serious damage to building components that have been tampered with If anomalies as per above were detected the owner or person acting for him must be warned in writing in the maintenance report to refrain from using the system until the safety conditions have been fully restored The inspection and maintenance report must include the main information of the technician or company who performed the inspection and or maintenance operations with their contact details date of intervention and the signature of the operator QExtraflame ENGLISH PELLETS AND FEEDING Pellets are made by subjecting wood shavings i e the rejects of pure wood without paint sawmill carpenter products and products from other activities connected to working and transforming wood to very high pressures Thi
15. works As well as programming it activate it as well INCORRECT Switch off time 05 00 TO ENABLE THE CHRONO FOLLOW THE INSTRUCTIONS AS DESCRIBED IN THE ENABLE CHRONO com CHAPTER WHEN THE WEEKLY PROGRAMMER IS ACTIVE THE RELEVANT ICON WILL LIGHT UP ON THE CONTROL PANEL ADJUSTING LANGUAGE see chapter commissioning settings DISPLAY The DISPLAY menu contains two sub menus Key lock Brightness KEY LOCK The menu allows to lock the display keys like with mobile phones CONTROLS PROCEDURE Press key 6 and SET POWER will appear Press key 2 several times until USER is displayed Confirm using key 6 Press key 2 until DISPLAY Confirm using key 6 KEY LOCK will appear confirm with key 6 Use keys 4 5 to enable ON disable OFF Press key 6 to confirm and key 1 to return to the previous menus up to the initial status o o USING THE KEY LOCK AFTER ACTIVATION Dr TO LOCK THE KEYBOARD PRESS KEYS 1 AND 5 AT THE SAME TIME UNTIL THE FOLLOWING APPEARS KEYS LOCKED TO UNLOCK THE KEYBOARD PRESS KEYS 1 AND 5 AT THE SAME TIME UNTIL THE FOLLOWING APPEARS KEYS FREE Extraflame ENGLISH BRIGHTNESS This menu allows to adjust the brightness of the display The possible settings range from OFF 10 to 31 Activating OFF the back light of the display will go off after a preset delay The back light will go on as soon as a key is pressed or if an alarm should be triggered in the m
16. BY DISABLED When the STBY function is disabled the LED is fixed When the contact or external thermostat is satisfied open contact temperature reached the stove will go to minimum As soon as the contact or external thermostat switches to the not satisfied status closed contact temperature to be reached the stove will start to work again at the pre set power N B stove operation depends on the temperature of the water inside the stove and relative factory setting restrictions If the stove is in H OFF water temperature reached any additional contact or thermostat request will be ignored ADDITIONAL ROOM THERMOSTAT INSTALLATION Switch the appliance off using the master switch positioned on the rear of the stove Remove the plug from the socket Refer to the electrical diagram to connect the two thermostat cables onto the relative clamps positioned on the rear of the machine one is red and the other one is black STBY clamp AUX Connection reserved for Extraflame conveyed waves accessories Contact the dealer for further details ISTBY THE STBY AND AUX CLAMPS lt FOUND AT THE BACK OF THE elf STOVE CAN BE NOTED IN THE DIAGRAM TO THE SIDE QEXxtraflame ENGLISH
17. CONDITIONS e WITHTHE STOVE FULLY COOLED DOWN SWITCHED OFF AND DISCONNECTED FROM THE MAINS ELECTRICITY SO gt FAILURE TO CLEAN JEOPARDISES SAFETY FOR PROPER OPERATION THE STOVE MUST UNDERGO ROUTINE MAINTENANCE BY A QUALIFIED TECHNICIAN AT LEAST ONCE A YEAR QExtraflame ENGLISH ROUTINE MAINTENANCE Fumes motor disassembly and cleaning and fumes pipe and T new silicone in required points Inspections of gaskets ash drawer and door replace them and apply silicone where required Combustion chamber amp heat exchanger full cleaning and ignition plug duct cleaning Tank complete emptying and cleaning SIN SER N Air intake pipe inspection and of flow sensor cleaning 00 QExtraflame ENGLISH DISPLAYS DISPLAY REASON OFF Stove off START The start up phase is in progress PELLET FEEDING Continuous pellet feeding is in progress during the ignition phase IGNITION The ignition phase is in progress START UP The start up phase is in progress WORK The normal work phase is in progress MODULATION The stove is working at minimum BURN POT CLEANING Automatic burn pot cleaning is in progress FINAL CLEANING The final cleaning is in progress STAND BY St
18. ER MENU is displayed m Di LANGUAGE GERMAN g key SET CLOCK will appear FRENCH Press key 2 until SET LANGUAGE appears SPANISH Confirm using key 6 Select the language using key 4 or 5 Press key 1 several times to confirm and exit the menu BURN POT UPPER DIVIDER IT IS FORBIDDEN TO USE THE APPLIANCE WITHOUT THE DIVIDER AND OR GLASS PROTECTION SEE THE FIGURE TO THE SIDE ITS REMOVAL JEOPARDISES THE SAFETY OF THE PRODUCT AND IMMEDIATELY VOIDS THE WARRANTY PERIOD IN THE CASE OF WEAR OR DETERIORATION REQUEST AFTER SALES ASSISTANCE FOR REPLACEMENT OF THE PART REPLACEMENT THAT IS NOT UNDER GUARANTEE AS THE COMPONENT IS SUBJECT TO WEAR CLEAN CHECKUP 1 2 SHOULD THE ALARM CLEAN CHECK UP BE TRIGGERED MAKE SURE THAT THE BOTTOM OF THE BURN POT IS FREE FROM RESIDUES OR SCALING THE HOLES ON THE SIDE OF THE BURN POT SEE FIGURE TO THE SIDE MUST BE Kore COMPLETELY CLEAR TO ENSURE PROPER COMBUSTION SEE CHAPTER CLEANING UNDER USER S RESPONSIBILITY ONE CAN USE THE PELLET FEED ADJUSTMENT FUNCTION TO ADJUST THE COMBUSTION ACCORDING TO THE DESCRIBED REQUIREMENTS IF THE ALARM PERSISTS AND THE ABOVE LISTED CONDITIONS HAVE BEEN CHECKED CONTACT THE QUALIFIED AFTER SALES ASSISTANCE CENTRE BURN POT HOLES Extraflame OPERATION AND LOGIC ENGLISH IGNITION Once the points listed previously have been checked press key 1 for three seconds to ignite the stove 15 minutes are available for the ignition p
19. ER OR HEATING OF THE MACHINE IS IN THE FOLLOWING STATE TOFF HOFF OR STBY REQUESTS SATISFIED ONE MUST WAIT FOR THE MACHINE TO SWITCH ON AGAIN QExtraflame ENGLISH ADDITIONAL ROOM THERMOSTAT N B Installation must be performed by an authorised technician There is a possibility to thermostat a room adjacent to the room where the stove is positioned just connect a thermostat following the procedure described in the next step it is recommended to position the optional mechanical thermostat at a height of 1 50 m from the floor Stove functioning with the external thermostat connected in the STBY clamp can be different on the basis of the activation or disabling of the STBY function The STBY clamp leaves the factory jumpered therefore it is always with closed contact on request ADDITIONAL ROOM THERMOSTAT FUNCTIONING WITH STBY ACTIVE When the STBY function is activated the gt LED flashes When the contact or external thermostat is satisfied open contact temperature reached the stove will switch off As soon as the contact or external thermostat switches to the not satisfied status closed contact temperature to be reached it will re ignite N B stove operation depends on the temperature of the water inside the stove and relative factory setting restrictions If the stove is in H OFF water temperature reached any additional contact or thermostat request will be ignored ADDITIONAL ROOM THERMOSTAT FUNCTIONING WITH ST
20. Indicates the stove modulation On during radio communication On the stove is working at the set power Off no radio communication Flashing the power at which the stove is working is different to the power Flashing serial port excluded set the stove is modulating for various reasons Indicates the presence of an alarm GEN R MN A On indicates the presence of an alarm It indicates weekly programming functioning Indicator on weekly programming active i Indicator off weekly programming disabled Flashing indicates the deactivation of the depression sensor Indicates the contact of the external additional thermostat Contact closed the contact of the external additional thermostat is closed and the STBY function is disabled Indicates the water temperature status 6 Contact open the contact of the external additional thermostat is open and Off the T read by the probe is above the set temperature the STBY function is disabled On the T read by the probe is below the set temperature y Flashing with contact closed the contact of the external additional thermo stat is closed and the STBY function is activated Flashing with contact open the contact of the external additional thermostat is open and the STBY function is activated It indicates functioning of the fumes motor It indicates the summer winter function Off flue gas motor deactivated Off Activates the winter
21. OL IS OFF BECAUSE IT HAS NO BATTERIES THE STOVE CAN BE CONTROLLED FROM THE CONTROL PANEL ON TOP OF IT WHILE REPLACING THE BATTERY PAY ATTENTION TO THE POLARITY BY OBSERVING THE SYMBOL ON THE INSIDE COMPARTMENT OF THE REMOTE CONTROL QExtraflame ENGLISH COMMISSIONING SETTINGS Once the power cable at the back of the stove has been connected move the switch also located on the back to 1 The switch at the back of the stove powers the stove board The stove remains off and a first screen appears on the panel reading OFF ADJUSTING TIME DAY MONTH AND YEAR Set clock allows to adjust the time and date SET CLOCK CONTROLS PROCEDURE DAY MON TUE WED SUN Press key 6 and SET POWER will appear Press key 2 several times until USER MENU is displayed HOURS 2223 Confirm using key 6 MINUTES 00 59 SET CLOCK will appear DATE 1 31 Confirm using key 6 MONTH 1 12 Use key 4 5 to select the day YEAR 00 99 Proceed by pressing key 2 Use the same procedure 4 or 5 to set and key 2 to move forward to adjust the hours minutes day month and year Press key 1 several times to confirm and exit the menu ADJUSTING LANGUAGE It is possible to select the preferred language to display the various messages SET LANGUAGE CONTROLS PROCEDURE ITALIAN Press key SET POWER will appear ENGLISH Presskey 2 several times until US
22. ONNECTIONS AIR INTAKE FLUE EXHAUST AND DIMENSION SPECIFICATIONS OF THE PRODUCT IN QUESTION QExtraflame ENGLISH STOVE POSITIONING For correct product functioning it is recommended to position it so that it is perfectly level using a spirit level REARMS The figures below illustrate the positions of the tank 85 C and H20 100 C rearms Contact the qualified technician if one of the rearms should be triggered so as to verify the cause AUX DIADEMA ACS IDRO FEATURES DIADEMA ACS IDRO Water content of the thermo product heat exchanger I 21 Volume of expansion vessel integrated in the thermo product I 8 3 bar safety valve integrated in the thermo product SI Minimum and maximum pressure switch integrated into the thermo product SI Pump integrated into the thermo product SI Pump max head m 5 ENVISION A POSSIBLE ADDITIONAL EXPANSION VESSEL DEPENDING ON THE SYSTEM WATER CONTENT 4 E 3 The diagram to the side illustrates the behaviour of the pump used on our thermo products at the speeds that can be set 1 0 0 0 0 5 1 0 1 5 2 0 2 5 Flow rate m h Extraflame SAFETY DEVICES SAFETY DEVICES STOVES KEY PRESENT PRESENT Circuit board it intervenes directly sending the
23. SIC LAYOUT sccsssosssssssesssreserens SAFETY DEVICES csssnrsnsennennsensennseneonnennsennennsensonnsonsennennsennennsensennsensenntnnsennenntensenntensenntnnsennenntensenntensennsnnsennennsensennsensennsnnssnnennee REFERENCE STANDARDS CIENIE AL ee RR IN SIEANEIEAT ION a acc R ccc cc A FUMES EXHAUST SYSTEM cseeeeeeseeseeesersesosessossessseesesssess0s0n00000000000000000000000000000000000000000000000000000000000090009009000900000000090090000000008 GENERAL REQUIREIENIE PE SMOKE DUCT FUMES EXHAUST SYSTEM PRODUCT REQUIREMENTS vve LERLE oversee MEGLINICAL INSTALLATION eee KA PEBBENS AND REEBING ve vene ALEEN 0000000090 eo Extraflame ENGLISH CONTROL PANEL sscrrserereresezesee nese nese nesee rien nese nese nesea nia nese nese n nea nese nese nesee nina nasa nese azien nese nese nese anice nese 21 DISPLAY ICONS KEY scan 21 GENERAL 22 BASIC INSTRUCTIONS ae ana iena 22 THE REMOTE CONTROL 23 ENABLE DELAYED SWITCH riesci 23 REPLACEMENT OF BATTERIES accccossssssssecsossonsscccntessscssscsuvosnavesosnssstonstnussvarassen
24. STAND BY FINAL CLEANING and OFF conditions it cannot supply heat for the production of hot water In the H OFF T OFF conditions the stove is switched off because it has satisfied all heat requests in this case a request for domestic water will make the stove switch on again but one must wait for the time required for it to reach steady state conditions In the event of STAND BY the stove is switched off because it has satisfied the additional thermostat STBY clamp in this case a request for domestic water will not make the stove switch on again until the additional thermostat is in request conditions because the contact has priority over any request Even in this case one must wait for the time required for steady state conditions Avoid sampling hot water with very limited flow rates Flow rates below 3 litres per minute can make the thermo stove switch from the OPERATION state to the H OFF state with consequent appliance shutdown It is recommended to always leave a heating zone open in order to ensure the dissipation of any excess heat produced by the thermo stove In order to prevent burns one must fit a thermostatic mixing valve in order to limit the temperature of the domestic water sent to the utilities One must provide a suitable water filtration and softening system according to the specific hardness of the water in the place where the heat exchanger is installed The excessive deposit of limescale as well as reducing the effi
25. T element must not be more than 4 VA EXAMPLES OF CORRECT CONNECTION TO THE CHIMNEY Installation with internal flue Insulated flue Installation with internal external flue Protection from rain and wind Condensation proof T fitting with n IND 7 7 inspection plug Protection from rain and wind ba si LI woe LAC Insulated flue Insulated condensation proof T fitting with inspection plug IT IS NOT RECOMMENDED TO INSTALL A 90 BEND AS THE FIRST INITIAL PART SINCE THE ASH WOULD BLOCK THE PASSAGE OF THE FUMES IN A SHORT TIME CAUSING PROBLEMS TO THE STOVE DRAUGHT SEE FIGURES BELOW Ash deposited in the 90 bend Ash deposited in the 90 bend Extraflame ENGLISH EXAMPLES CORRECT CONNECTION TO THE CHIMNEY Protection from rain and wind Protection from rain and wind DD Steel plate si gt airtight y 7 O X 0 Max 3 mt e 35 A Insulated T fitting with T fitting with in
26. TRAFLAME S p A Via Dell Artigianato 12 36030 MONTECCHIO PRECALCINO VI ITALY FN 39 0445 865911 E 39 0445 865912 info extraflame it www lanordica extraflame com Extraflame reserves the right to vary the features and data shown in this booklet at any time and without prior notice in order to improve its products This manual cannot be considered as a contract for third parties This document is available at www extraflame it support 004275996 manuale utente Diadema ACS Idro 514 001
27. able load bearing capacity to support the weight of the appliance of the accessories and coatings The adjacent side and rear walls and the supporting surface must be made of non combustible material according to the table REFERENCES INFLAMMABLE OBJECTS NON INFLAMMABLE OBJECTS A 200 mm 100 mm B 1500 mm 750 mm 200 mm 100 mm figure 1 Inspection figure 2 9 Air inlet S floor protection In any case the temperature of the adjacent combustible materials must not reach a temperature equal to or greater than the room temperature increased by 65 C The minimum volume of the premises in which to install the appliance must be greater than 15 m Extraflame ENGLISH VENTILATION AND AERATION OF THE INSTALLATION PREMISES Ventilation is deemed sufficient when the room is equipped with air inlets according to the table Air inlet See figure 2 Percentage ofthe gt net opening section with Minimum net opening value of Appliance categories Referen ndar 3 BRL 9 eference standard respect to the appliance fumes the ventilation duct outlet section Pellet stoves UNI EN 14785 80 cm In any case ventilation is deemed sufficient when the pressure difference between the external and internal environment is equal to or less than 4 Pa In the presence of type gas appliances with intermittent operation not intended for heating they must hav
28. according to the requirements laid down by the technical standards in force and by the manufacturer s use and maintenance manual QExtraflame ENGLISH HYDRAULIC SYSTEM Certain concepts referring to the Italian Standard UNI 10412 2 2009 are described in this chapter As previously described when installing all national regional provincial and council Standards in force provided by the country in which the appliance has been installed must be complied with TABLE OF SAFETY DEVICES FOR CLOSED VESSEL SYSTEM FEATURED AND NOT FEATURED IN THE PRODUCT Safety valve Pump control thermostat it is controlled by the water probe and the board program Acoustic alarm activation thermostat Water temperature indicator display iI Pressure indicator Acoustic alarm Automatic adjustment circuit breaker switch managed by board program Minimum and maximum pressure switch Water overheating automatic circuit breaker switch block thermostat Circulation system pump SENNO Expansion system During installation of the stove it is MANDATORY to adjust the system with a manometer in order to display the water pressure INSTALLATION AND SAFETY DEVICES The installation relative system connections commissioning and inspection of correct functioning must be carried out with the highest professional standards in full compliance with the national regional and council Standards in force
29. achine CONTROLS PROCEDURE Press key 6 and SET POWER will appear Press key 2 several times until USER is displayed Confirm using key 6 Press key 2 until DISPLAY appears and confirm with key 6 Press key 2 until BRIGHTNESS appears and confirm with key 6 Press keys 4 5 to select the brightness Press key to confirm and key 1 to return to the previous menus up to the initial status 0 9199 RESET Allows to reset all values modifiable by the user to the default values The data is SET H20 75 C CONTROLS PROCEDURE SET POWER 5 Press key SET POWER will appear ENABLE CHRONO OFF Press key 2 several times until USER is displayed START PRG1 OFF Confirm using key 6 STOP OFF Press key 2 until RESET appears MONDAY PRG1 OFF Confirm using key 6 all chrono parameters OFF Press keys 4 5 to select ON and press key 6 PELLET 00 A BURN POT CLEANING 00 DONE will appear on the display to confirm STAND BY OFF BOILER CHRONO CANNOT BE ACTIVATED Diadema ACS features an instantaneous heat exchanger for the production of domestic hot water and it is not possible to set the Boiler timer OTHER FUNCTIONS AIR DISCHARGE This function allows to bleed any air in the stove Once the function has been activated the pump indicator light is activated on the display for 15 minutes 30 seconds the pumps will be powered alternating with 30 sec
30. c mixing valve is used in solid fuel boilers as it prevents cold water from returning into the exchanger Routes 1 and 3 are always open and together with the pump installed on the return they guarantee water circulation inside the biomass boiler exchanger A high return temperature allows efficiency improvement reduces formation of smoke condensation and prolongs the boiler life span Valves on the market have different calibrations Extraflame advises to use model 55 c with 1 hydraulic connections Once the valve calibration temperature is reached route 2 is opened and the boiler water goes to the system via the flow Valve sold as an accessory optional Extraflame ENGLISH HYDRAULIC PLANT BASIC LAYOUT KEY A Combustion air inlet 60mm B Smoke exhaust outlet 120mm 1 3 bar safety valve 1 2 T2 Boiler flow output 1 T3 Boiler return inlet 1 T4 Domestic cold water inlet 1 2 T5 Domestic hot water outlet 1 2 M Pressure Gauge T Thermometer TS Domestic terminals R Feed valve VB Balance valve VMTA Thermostatic mixer valve 55 C VMS Domestic water mixing valve IT IS RECOMMENDED TO CONSULT THE TEMPLATES MANUAL ON THIS WEBSITE FOR FURTHER INFORMATION RELATING TO THE HYDRAULIC C
31. chapter commissioning settings Extraflame CHRONO ENGLISH The chrono allows to program 4 time spans within a day to use every day of the week The switch on and switch off time can be set in every time slot along with the days of use of the programmed time slot and the desired water temperature 65 80 C PROGRAMMING EXAMPLE Let s suppose that the weekly programmer function is to be used and 4 time slots are to be used in the following way 1st time slot from 08 00 to 12 00 every day ofthe week excluding Saturday and Sunday 2nd time slot from 15 00 to 22 00 only on Saturday and Sunday both times with a water temperature setting of 75 C 1ST TIME SLOT SWITCH OFF ED SS Dr Use keys 4 5 to enter the time 12 00 STOP PRG1 Press key 6 once and SET POWER will SET which to me 282 time of the 1st time slot USER 6 Press key 2 until SET USER appears programming STOP PRG1 press button 6 Press button 3 to go 12 00 back to the previous parameter ENABLING THE 1ST TIME SLOT DAYS To enable ON disable OFF the days MONDAY PRG1 Press key 6 to confirm ON SET CLOCK will appear Hee keys 4 ands i SET CHRONO r Keys 2 and 3 to scroll the various days Press 2 until SET CHRONO select from Monday to Friday on ON FRIDAY PRG1 excluding Saturday and Sunday OFF ON To confirm and proceed press
32. ciency of the plate heat exchange can compromise its operation Replacement of the plate heat exchanger in the event of excessive fouling it not covered by the warranty Extraflame ENGLISH The kit for the production of domestic hot water plate NE heat exchanger motorised diverter valve and flow switch is controlled by a board integrated in the stove system expansion board kit which allows various hydraulic configurations up to a maximum of four heating zones a OUT3 N o 230V 50 Hz output heating area 3 max 5A puffer and an auxiliary boiler 230 V 50 Hz output heating or Neutral and phase OUT1 N 230V 50 Hz output heating area 1 max 5A OUT2 N 230 V 50 Hz output heating area 2 max 5A Ouran puffer pump area 4 max 5 A 230 V 50 Hz output max 5A normally closed O5NC N for DHW 230V 50 Hz output max 5A normally open O5NO N for DHW 06 6 auxiliary output normally open NC O6C auxiliary output normally closed 11 GND area 1 input dry contact 12 GND area 2 input dry contact 13 GND area 3 input dry contact I4A GND area 4 input dry contact 14B GND Future preparation 15 GND boiler heat exchanger probe inlet GND n GND Z Jeno lonn ma ee GND 15 END GND 16 GND upper puffer probe inlet 17 GND lower puffer probe inlet OC power line connection red black MODES SUMMER WINTER the mode allo
33. e following menu allows to adjust the percentage of pellet feed If the stove has functioning problems owing to the quantity of pellets adjust pellet feeding directly from the control board The problems correlated to the amount of fuel can be divided into 2 categories NO FUEL the stove can never develop a suitable flame tending to remain very low even at high powers at minimum power the stove tends to almost switch off taking the stove into NO PELLETS alarm condition when the stove displays the NO PELLETS alarm there may be non burned pellets inside the burn pot EXCESS FUEL the stove develops a very high flame even at low power the panoramic glass is very dirty obscuring it almost totally the burn pot tends to become encrusted blocking the holes for air intake due to the excessive pellet feed as it is only burned partially Extraflame ENGLISH The adjustment to be performed is in percentage Therefore a modification of this parameter will lead to a proportional variation of all stove feeding speeds Feeding is from 30 to 42096 Follow the procedure on the display to perform this adjustment CONTROLS PROCEDURE Press key and SET POWER will appear Press key 2 several times until SET ADJUSTMENTS is displayed Confirm using key 6 Press key 2 until PELLET is displayed Press 4 to increase the load and 5 to decrease it Press key 6 to confirm and key 1 to return to the previous menus up to the ini
34. e their own aeration and or ventilation opening The air inlets must meet the following requirements they must be protected with grids metal mesh etc but without reducing the net useful section they must be made so as to make the maintenance operations possible positioned so that they cannot be obstructed The air flow can also be obtained from a room adjacent to that of installation indirect aeration and ventilation as long as the flow takes place freely through permanent openings communicating with the outside The adjacent room cannot be used as a garage warehouse of combustible material or for any other activity with a fire hazard bathroom bedroom or common room of the building FUMES EXHAUST SYSTEM GENERAL REQUIREMENTS Each appliance must be connected to a suitable fumes exhaust system and ensure adequate dispersion of the combustion products into the atmosphere The combustion products must discharged above the roof Direct discharge from the wall or towards closed spaces is forbidden even with clear skies In particular it is forbidden to use flexible and extendible metal pipes The chimney should only receive the exhaust of the smoke duct connected to the appliance collective flues or conveying exhausts from hoods above cooking appliances of any kind or exhausts from other generators into the chimney itself or smoke duct are not allowed The smoke duct and the chimney must be connected with a continuity solution
35. ed the same plant or the same secondary circuit each heat generator must be connected directly to the expansion vessel or plant expansion vessels unit altogether dimensioned for the total volume of water contained in the same plant or the same independent circuit Where it is necessary to separate the individual heat generator from the expansion vessel or expansion vessels unit a three way valve with the same characteristics listed above must be applied on the connection piping between the generator and the vessel in order to ensure in every position the connection of the generator with the expansion vessel or with the atmosphere The expansion vessels the connecting pipes the bleed pipes and drain pipes must be protected from frost where applicable The solution used for this purpose is described in the design COMMISSIONING CHECKS Before connecting the boiler a wash all system piping thoroughly in order to remove any residues which might compromise the correct functioning of certain system components pumps valves etc b check to verify that the flue has adequate draught that it is not narrowed and that other appliances do not discharge into the flue This is to prevent unexpected power increases The flue fitting can be mounted between the boiler and the flue only after this inspection An inspection of the connections with pre existing flues is recommended AUTOMATIC THERMOSTATIC MIXER VALVE MANDATORY The automatic thermostati
36. em incorporated in the generator with thermal safety valve self activated whenever the appliance does not have a temperature self adjustment system 9999999 SAFETY VALVES The load capacity of the safety valve must allow the discharge of a certain amount of vapour not lower than Q 0 58 kg h where Q is the useful outlet power to the generator water expressed in kilowatt The diameter of the minimum net transversal section of the valve inlet must not be lower than 15 mm The valve load pressure equal to the calibration pressure increased by the overpressure cannot exceed the maximum operating pressure of the heat generator The design engineer must check that the maximum pressure existing in every point of the system does not exceed the maximum operating pressure of every component The safety valve must be connected to the highest part of the heat generator or outlet pipes right next to the generator The length ofthe pipes section included between the attachment to the generator and the safety valve must not be more than 1 m The connection piping of the safety valve to the heat generator must not be traceable and must not feature Extraflame ENGLISH in any point a smaller section than the inlet of the safety valve or the sum of the inlet sections in the event of several valves belonging to a single pipe The discharge piping of the safety valve must be make so as not to prevent the regular operation of the valves and not to cau
37. ermostat or be equipped with a cooling circuit installed by the appliance manufacturer The cooling circuit must be activated by a heat safety valve such to guarantee that the limit temperature set by the Standard is not exceeded Connection between the power supply unit and the valve must be free from interceptions The pressure upstream of the cooling circuit must be at least 1 5 bar TYPE OF SYSTEM There are 2 different types of system Open vessel system and closed vessel system The product has been designed and made to work with closed vessel systems CLOSED VESSEL SYSTEM System in which the water it contains is not in direct or indirect communication with the atmosphere Generally the closed vessel system features one of the following expansion vessels Pre loaded closed expansion vessel with membrane impermeable to the passage of gases Automatic closed expansion system with compressor and membrane impermeable to the passage of gases Automatic closed expansion system with transfer pump and membrane impermeable to the passage of gases Expansion system without diaphragm GENERAL The closed systems must have Safety valve Pump control thermostat Acoustic alarm activation thermostat Temperature indicator Pressure indicator Acoustic alarm Adjustment automatic circuit breaker switch Automatic blockage circuit breaker switch thermostat blockage Circulation system Expansion system Safety dissipation syst
38. function On flue gas motor active i On Activates the summer function Flashing breakdown contact technical after sales service Indicates the DHW request Off DHW satisfied pump off Notuted Flashing the DHW request exists but the work conditions are not satisfied eN pump off ino On the DHW is in request mode and the work conditions are satisfied pump on Indicates the heating request 6 Off heating satisfied pump off Flashing the heating request exists but the work conditions are not satisfied pump off On the heating is in request mode and the work conditions are satisfied pump on 4 It indicates functioning of the pellet feed motor Off pellet feed motor deactivated On pellet feed motor active VO E Indicates the puffer reguest if active Itindicates pump operation Off puffer satisfied pump off Off pump deactivated Flashing the puffer request exists but the work conditions are not satisfied On pump active 3 pump off Flashing the safety device is active 20 temperature gt 85 C On the puffer is in request mode and the work conditions are satisfied pump on GENERAL MENU Extraflame ENGLISH 1 GO BACK EXIT 6 CONFIRM ACCESS MENU 2 3 PARAMETER SCROLLING NEXT 2 PREVIOUS 3 45 MODIFY SETTINGS DATA INCREASE
39. gs and finishings must only be applied after having verified the proper operation of the appliance according to the indicated modalities TECHNICAL INSTALLATION DOCUMENTATION When installation is complete the installer must provide the owner or person acting for him according to the legislation in force with the declaration of conformity supplied with 1 the use and maintenance manual of the appliance and of the system components such as for example the smoke ducts chimney etc 2 photocopy or photograph of the chimney plaque 3 system booklet where applicable The installer must ask to be issued with a receipt stating that the documentation has been provided and must keep it with a copy of the technical documentation relating to the installation Installation performed by several parties Ifthe individual installation steps are carried out by different parties each must document the work carried out for the customer and the for the operator working on the next step INSPECTION AND MAINTENANCE Frequency of operations Maintenance of the heating system and of the appliance must be carried out on a regular basis according to the table below TYPE OF APPLIANCE INSTALLED lt 15kW 15 35 kW Pellet operated appliance 1 year 1 year Water operated appliances 1 r 1 r closed fireplaces thermo stoves thermo kitchens yea yea Boilers 1 year 1 year Fumes exhaust system 4 t of fuel used 4 t of fuel
40. hase After ignition and having reached the control temperature the stove interrupts the ignition phase and passes to STARTING STARTING During the start up phase the stove stabilises combustion increasing it progressively to then start ventilation and pass on to WORK WORK During the work phase the stove reaches the set power see following item SET POWER ADJUSTMENT Set the operating power from 1 to 5 Power 1 minimum level Power 5 maximum level SET H20 TEMPERATURE ADJUSTMENT Set the boiler temperature between 65 80 C PUMP OPERATION The pump activates water circulation when the t of the water inside the stove reaches 60 C As the pump always functions above 60 an always open heating area is recommended to make product functioning homogenous preventing overheating blocks Normally this area is defined Safety zone BURN POT CLEANING At pre set intervals the stove performs burn pot cleaning switching the machine off When the cleaning phase is finished the stove will re start automatically and continue its work going back to the power level selected MODULATION and H OFF As the water temperature approaches the set point the boiler starts to modulate automatically bringing itselfto the minimum power Ifthe temperature increases beyond the set point it will automatically switch off indicating H OFF and will automatically go back on when the temperature drops below the set point SWITCH OFF Press ke
41. he ash in the combustion chamber at least once a week using a suitable vacuum cleaner MAKE SURE THAT THE ASH IS COMPLETELY COLD BEFORE EMPTYING IT INTO A SUITABLE CONTAINER Extraflame ENGLISH CLEANING UNDER USER S RESPONSIBILITY MONTHLY Cleaning the deflector The fumes deflector located in the upper part of the combustion chamber must be removed on a monthly basis see figure to the side To remove it simply pull out the central fumes deflector as if it were a drawer ROUTINE MAINTENANCE In order to guarantee proper functioning and safety of the device the operations indicated below must be performed every season or more often when necessary DOOR ASH DRAWER AND BURN POT GASKETS The gaskets ensure the tightness of the stove and its consequent proper operation They must be checked periodically in the event they are worn or damaged they must be replaced immediately These operations must be carried out by a qualified technician CONNECTION TO THE FLUE Vacuum and clean the pipe that leads to the flue yearly or whenever necessary If there are horizontal sections the residues must be removed before they can obstruct flue passage ALWAYS FOLLOW THE INSTRUCTIONS IN MAXIMUM SAFETY
42. llation site verification of the suitability of the fumes exhaust system verification of the suitability of the outside air inlets 2 Installation implementation of ventilation and connection to the outer air inlets implementation and connection to the fumes exhaust system assembly and installation electric and hydraulic connections installation of insulation ignition and operation test installation of finishings and coverings gt gt gt 3 Issue of complementary documentation 4 Inspection and maintenance Other actions may be required in relation to specific requests of the competent authority PRELIMINARY ACTIVITIES GENERAL Verification of compatibility of the system of any restrictions required by local administrative regulations special or conventional requirements resulting from condominium regulations constraints laws or administration deeds must precede any other assembly or installation operation One must especially verify the suitability of the installation premises of the appliances already installed in the installation premises and in the adjacent and adjoining premises also powered by different fuels with particular reference to non compliant installations of the fumes exhaust system of the outside air inlets SUITABILITY OF THE FUMES EXHAUST SYSTEM Installation must be preceded by a compatibility test between the appliance and the fumes exhaust system by ve
43. n of the depression sensor The alarm can be reset by pressing key 1 for 3 seconds only if the fumes motor has stopped and if 15 minutes have elapsed from when the alarm was displayed Contact after sales centre FUMES PROBE Fumes probe failure Contact after sales centre HOT FUMES High flue gas temperature Check pellet feed see Pellet feed adjustment If the problem cannot be solved contact an authorised technician CLEAN CHECK UP 1 2 1 IN START UP STAGE 2 IN OPERATING STAGE The door is not closed correctly The ash drawer is not closed correctly The combustion chamber is dirty The flue exhaust pipe is blocked Check hermetic door closure Check hermetic closure of the ash drawer Check cleanliness of the fumes pipe of the sensor in the primary air channel and the combustion chamber Check for the presence of pellets in the feed box NO The pellet feed box is empty SA Adjust pellet flow see Pellet feed adjustment IGNITION Check the procedures described the Ignition chapter NO IGNITION ine Set the stove on OFF using key 1 and repeat the procedure BLACK OUT 9 9 described in the Ignition chapter NO PELLETS er s empty Check for the presence of pellets in the feed box The motor reducer does not feed pellets Adjust the pellet flow see Pellet feed adjustment The door is not closed correctly Check he
44. ng a prolonged period of inactivity The stove has been designed to function in any climatic condition even critical In particularly adverse conditions strong wind freezing safety systems may intervene that switch the stove off If this occurs contact the technical after sales service and always disable the safety systems In the event the flue catches fire use suitable systems for suffocating the flames or request help from the fire brigade This appliance must not be used to burn waste Do not use any flammable liquids for ignition During the filling phase do not put the bag of pellets to into contact with the product The majolicas are top quality artisan products and as such can have micro dots crackles and chromatic imperfections These features highlight their valuable nature Due to their different dilation coefficient they produce crackling which demonstrate their effective authenticity To clean the majolicas it is recommended to use a soft dry cloth If a detergent or liquid is used the latter could penetrate inside the crackles highlighting them 60 6 99999 gt ROUTINE MAINTENANCE Based on Decree 22 January 2008 n 37 art 2 routine maintenance means interventions aimed at reducing degradation due to normal use as well as dealing with accidental events entailing the need of first interventions which however do not modify the structure of the system upon which one is intervening or its intended use
45. ns to be carried out on the roof Verify the presence of other chimney caps or skylights and dormers FUMES EXHAUST SYSTEM PRODUCT REQUIREMENTS Temperature class In the event of a pellet appliance temperature classes below T200 are not allowed Soot fire resistance class The fumes exhaust system interlocked with appliances supplied by solid fuels require soot fire resistance and the specification must be indicated by the letter G followed by the distance from combustible materials in millimeters XX in compliance with UNI EN 1443 In the event of pellet appliances the fumes exhaust systems must be airtight if double designation elements are used G and O with or without seal elastomer for connecting the appliance to the chimney one must comply with the minimum distance XX in millimeters indicated for designation G in the event of fire due to soot one must ensure the restoration of the initial conditions by replacing the gaskets and damaged items and cleaning those remaining in use Ignition tests Operation of the appliance must be verified with an ignition test i e for mechanical feed appliances one must complete the ignition test verify proper operation for at least the next 15 minutes and adjust the switch off For appliances installed in a hot water heating system closed fireplaces thermo stoves testing must also extend to the entire hydraulic circuit Extraflame ENGLISH Coverings and finishings The coverin
46. of that of the chimney ducted system on which it is installed they must be adapted in order to prevent the penetration of rain and snow in the chimney ducted system they must be built so that in the event of winds coming from all directions and from any angle the expulsion of combustion products is in any case ensured they must be free from mechanical intake aids QExtraflame ENGLISH COMBUSTION PRODUCTS OUTLET QUOTA The outlet quota is determined by measuring the minimum height between the roof covering and the lower point of the fumes expulsion section into the atmosphere this quota must be outside the reflux area and at an adequate distance from obstacles which hinder or make the expulsion of the combustion products difficult or from openings or accessible areas Reflux area The outlet quota must be outside the reflux area calculated according to the indications below Near the ridge one considers the lowest between the two Buffer area for outlet quota Clear area for outlet quota above the roof slope 4 gt 10 REFERENCE DESCRIPTION CLEAR AREA MM Distance measured at 90 from the surface 1300 a Height above the ridge of the roof 500 The outlet of a chimney ducted system must not be near obstacles that may create turbulence areas and or prevent proper expulsion of combustion products and maintenance operatio
47. onds of downtime To activate the function With the stove OFF press keys 1 and 4 at the same time enter the password 77 using keys 4 and 5 and confirm with key 6 Cut the power to interrupt FIRST LOAD This function allows to activate the pellet feeding motor reducer for continuous functioning To activate the function When the stove is cold and OFF press keys 2 and 5 at the same time for a couple of seconds the scrolling message first load will appear on the display To interrupt continuous loading simply press key 1 Extraflame ENGLISH CLEANING UNDER USER S RESPONSIBILITY DAILY Burn pot Through a mechanical system the burn pot is cleaned at set intervals automatically by the boiler In the picture below one can see the burn pot with the opening underneath it It is in any case recommended to remove any ash residue using a vacuum cleaner at least once every 2 days Scrapers The heat exchangers must only be cleaned when the stove is cold Cleaning the heat exchangers allows to ensure constant heat output over time This type of maintenance must be performed at least once a day To do this just use the relevant scrapers positioned in the upper part of the stove making upward movements and vice versa several times WEEKLY Clean the combustion chamber and the ash drawer Empty the ash drawer every week or when required It is recommended to remove t
48. ove off waiting for re ignition due to an external thermostat The stove will only re start when the external thermostat makes a request STAND BY A new ignition is attempted when the stove has just been switched off When the stove switches off one must wait for the complete shutdown of the fumes motor then clean the burn pot The stove can only be COOLING re ignited when these operations have been performed HOFF Stove off due to water temperature over set As soon as the water temperature drops below the pre set parameters the stove will switch back on T OFF Stove off waiting for re ignition as all the requests have been satisfied STAND BY The stove is cooling after a power cut BLACK OUT Once cooling is completed it will re start automatically The anti freeze function is in progress as the H20 t is below the factory set threshold ANTI FREEZE the pump is active until the water reaches the pre set factory parameter 2 C ANTILOCK The pump antilock function is in progress only if the stove has been in an OFF state for at least 96 hours the pump is activated for the time pre set by the manufacturer in order to prevent it from blocking AUTO BLOW The automatic blow is active Extraflame ENGLISH ALARMS DISPLAY EXPLANATION SOLUTION ASPIRATION FAULT Indicates the presence of an alarm Fumes motor fault On indicates the presence of an alarm Flashing indicates the deactivatio
49. product into alarm conditions until it has fully cooled down in the event of fumes motor breakage pellet feed motor breakage black out if above 10 seconds failed ignition Door micro switch With the door open the operation of the burn pot cleaning system is blocked Electronic pressure switch in the event of inadequate E depression it sends the machine in alarm conditions F 2 5 A 250V fuse stoves protects the machine from violent current surges 85 C calibrated mechanical bulb with manual rearm intervenes by blocking fuel feed whenever the pellet tank t reaches the limit of 85 C Rearm must be performed by qualified staff and or the manufacturer s technical after sales assistance Pellet tank temperature control probe if the tank over heats the machine automatically modulates to return to normal temperature values in the applicable models Mechanical air pressure switch blocks the pellet in the gt event of insufficient depression in the relevant models REFERENCE STANDARDS The installation must be in compliance with UNI10683 2012 heat generators fed with wood and other solid fuels installation The chimneys must be in compliance with UNI EN 13063 1 and UNI EN 13063 2 UNI EN 1457 UNI EN 1806 in the event of non metallic chimneys EN 13384 1 13384 chimneys Thermal and fluid dynamic calculation methods UNI EN 1443 2005 chimneys general requirements
50. raflame ENGLISH WARRANTY CONDITIONS EXTRAFLAME S p A with offices in via dell Artigianato 12 Montecchio Precalcino VI guarantees this product for 2 two YEARS from the date of purchase for manufacture and material faults The warranty becomes void in the event the defect is not reported to the dealer within two months from the date it was detected The responsibility of EXTRAFLAME S p A is limited to the supply ofthe appliance which must be perfectly installed following the indications contained in the appropriate manuals and booklets provided with the purchased product and in compliance with the laws in force Installation must be performed by qualified staff under the responsibility of the person entrusting him who will assume complete responsibility for the definitive installation and consequent good functioning of the product installed Extraflame S p A cannot be held responsible for the failure to comply with such precautions WARNING It is essential to carry out the functioning inspection of the product before its completion with the relative masonry finishings counterhood external coating pilasters wall painting etc EXTRAFLAME S p A does not assume any responsibility for any damages and consequent restore expenses of the above finishings even ifthe same occur following the replacement of malfunctioning parts THE WARRANTY IS VALIDATED ON THE CONDITION THAT EXTRAFLAME S p A assures that all its products are manufact
51. rifying the existence of documentation relating to the system existence and content of the chimney plaque suitability of the internal section of the chimney absence of obstructions all along the chimney predominantly vertical height and development of the chimney existence and suitability of the chimney cap distance of the outside wall of the chimney and of the smoke duct from combustible materials chimney type and material absence of other chimney connections 999999 Extraflame ENGLISH INSTALLATION Installation in premises with fire hazards is forbidden Installation in residential premises exceptfor sealed operation appliances is also forbidden in which there are liquid fuel operated appliances with continuous or intermittent operation which draw the combustion airintheroom in which they are installed or inwhich there are type gas appliances intended for room heating with or without production of domestic hot water and in adjacent and adjoining premises or in which in any case the depression measured during installation between the internal and external environment is greater than 4 Pa Installations in bathrooms bedrooms and studio flats Installation in bathrooms bedrooms and studio flats is only allowed for sealed or closed hearth appliances with ducted combustion air taken from the outside Installation premises requirements The support surfaces and or points must have a suit
52. riginal spare parts exclusively by an authorised after sales centre thus guaranteeing correct functioning SAFETY Thestovemustnot be used by persons including children with reduced physical sensory and mental capacities or who are unskilled persons unless they are supervised and trained regarding use of the appliance by a person responsible for their safety Children must be checked to ensure that they do not play with the appliance Do not touch the stove when you are barefoot or when parts of the body are wet or damp The safety and adjustment devices must not be modified without the authorisation or indications of the manufacturer Do not pull disconnect twist electric cables leaving the stove even if disconnected from the electric power supply mains It is advised to position the power supply cable so that it does not come into contact with hot parts of the appliance The power supply plug must be accessible after installation Do not close or reduce the dimensions of the airing vents in the place of installation The airing vents are essential for correct combustion Do not leave the packaging elements within reach of children or unassisted disabled persons The hearth door must always be closed during normal functioning of the product When the appliance is functioning and hot to the touch especially all external surfaces attention must be paid Check for the presence of any obstructions before switching the appliance on followi
53. rmetic door closure DEPR ALARM The ash drawer is not closed correctly Check hermetic closure of the ash drawer The combustion chamber is dirty Check cleanliness of the fumes pipe and the combustion The flue exhaust pipe is blocked chamber DEBIMETER Flow sensor faulty eran FAULT Sensor disconnected Possible air in the system vent the system Lack of adequate circulation Air in the system Lack of or inadeguate safety zone H20 OVERTEMP Unsuitable cire lation The water in the stove has exceeded 95 C Possible circulator anomaly If the problem persists the reset operations must be carried out by an authorised technician Check closure of the door Door not closed properly Check that the burn pot is clear and clean TRAPDOOR FAULTY Burn pot dirty or clogged The automatic burn pot cleaning is blocked If the problem persists contact the service centre Possible air in the system vent the system ALARM The system pressure read by the pressure Possible lack of water or leaks due to anomalies in some MINIMUM PRESSURE switch is too low system component Ifthe problem persists contact the service centre ALARM H20 probe failure Contact after sales centre H20 PROBE i Possible air in the system vent the system ALARM The pressure of the water has exceeded en vessels arenot damaged or MAX H20 PRESSURE the max threshold Check that the cold system is loaded at the correct pressure If the problem persists contact the service centre Ext
54. rts in refractory material Masonry work Thesystem particulars for the production of domestic hot water not supplied by EXTRAFLAME S p A water products only The heat exchanger is excluded from the warranty unless an adequate anti condensate circuit which guarantees a minimum return temperature of the appliance of at least 55 C only water products FURTHER CLAUSES The warranty also excludes any calibration or regulation interventions of the product in relation to the type of fuel or the type of installation The warranty is not extended if particulars are replaced No compensation will be paid for the time the product is inefficient This warranty is valid only for the purchaser and cannot be transferred RECOMMENDED INSPECTION WITH PAYMENT EXTRAFLAME S p A recommends that the functional inspection of the product is performed by a Technical After Sales Centre which will supply all information for correct use WARRANTY INTERVENTIONS The request for intervention must be sent to the dealer or after sales assistance Centre The warranty intervention envisions the repair of the appliance without any charge as provided by the law in force LIABILITY EXTRAFLAME S p A does not grant any compensation for direct or indirect damage caused or depending on the product LAW COURT The Vicenza Law Court is elected as the competent court for any disputes Extraflame ENGLISH uExtraflame Riscaldamento a Pellet EX
55. s type of fuel is fully ecological as no glues are used to hold it together In fact the compactness of the pellets is guaranteed over time by a natural substance that is found in wood lignin As well as being an ecological fuel as wood residues are made the most of pellets also have technical advantages While wood has a calorific value of 4 4 kW kg with 15 humidity therefore after about 18 months seasoning that of the pellet is 5 kW kg Pellet density is about 650 kg m and water content is equal to 8 of its weight For this reason the pellets do not need to be seasoned in order to obtain a sufficiently adequate heat yield The pellet used must comply with the features described by Standards EN PLUS UNI EN 16961 2 class 1 or A2 NORMM 7135 DIN PLUS 51731 Extraflame recommends using pellets with a diameter of 6mm with its products PELLET STORAGE To guarantee combustion without problems the pellets must be kept in a dry place Open the tank lid and load the pellets using a scoop THE USE OF POOR QUALITY PELLETS OR ANY OTHER MATERIAL DAMAGES THE FUNCTIONS OF YOUR STOVE AND VOID THE WARRANTY AND THE ANNEXED RESPONSIBILITY OF THE MANUFACTURER QExtraflame ENGLISH CONTROL PANEL BUTTON DISPLAY OF VARIOUS TO ACCESS ON OFF TEXT MESSAGES THE MENU au OPERATION POWER TEMPERATURE ADJUSTMENT SETTING DISPLAY ICONS KEY Indicates the receipt of the radio signal
56. se people injuries the discharge must flow right next to the safety valve and be accessible and visible The diameter of the discharge piping must not however be lower than that of the outlet connection of the safety valve By diameter of the outlet connection one refers to the minimum internal diameter on the valve outlet upstream of any internal threading CLOSED EXPANSION VESSEL Warning check that the preload of the expansion vessel is set at 1 5 bar The vessel maximum operating pressure must not be lower than the calibration pressure of the safety valve increased by overpressure typical of the valve itself bearing in mind the eventual level difference between vessel and valve and the pressure generated by the pump operation The capacity of the expansion vessel s is evaluated according to the total system capacity as per the design The closed expansion vessels must comply with the provisions regarding the planning manufacturing evaluation of conformity and use for pressure appliances Shut off parts or section reductions must not beinserted made on the connection piping which may consist of system portions The insertion of a three way shut off valve which allows connection between the vessel and the atmosphere for maintenance operations is allowed Such device must be protected against accidental manoeuvres The connection pipe must be made so as not to feature points with fouling or deposits In the event of several heat generators which fe
57. spection plug T fitting with inspection plug inspection plug It is mandatory to use airtight pipes CHIMNEY In addition to the general requirements the chimneys for releasing combustion products into the atmosphere must operate under negative pressure operation under positive pressure is not allowed have a preferably circular internal section square or rectangular sections must have rounded corners with a radius of no less than 20 mm hydraulically equivalent sections may be used as long as the ratio between the longer side and the shorter side of the rectangle which circumscribes the section is in any case no greater than 1 5 be designed for fumes be designed for fumes expulsion be predominantly vertical and have no narrowing along their entire length have no more than two direction changes with a slope angle no greater than 45 befitted with in the event of operating in damp conditions a device for reflux drainage condensation rainwater Ducted system A ducted system can be installed with one or more ducts operating only with negative pressure with respect to the environment The flexible hose compliant with UNI EN 1856 2 with T400 G characteristics meets the requirements CHIMNEY CAPS The chimney caps must meet the following requirements they must have a useful outlet section no less than double
58. st cross combustible materials the following indications must be complied with a b 1 i N L gt SYMBOL DESCRIPTION QUOTAIMM b Minimum distance of combustible materials from the intrados of the framework floor wall 500 b 1 Minimum distance of combustible materials from the extrados of the framework floor 500 a Minimum distance from combustible materials defined by the manufacturer G xxx The single wall pipes are indicated in white The insulated double wall chimney systems are indicated in grey One can disregard the quota only in the event of using an appropriate heat protection screen for example wall plate to protect the intrados of the framework floor SMOKE DUCT General requirements The smoke ducts must be installed in compliance with the following general requirements they must be insulated if they cross through rooms that are not to be heated or outside the building they must not cross rooms in which the installation of combustion appliances is forbidden nor in other premises compartmentalised against fire or with a fire hazard nor in rooms and or areas that cannot be inspected they must be installed so as to allow normal thermal expansion they must be fitted to the opening of the chimney without protruding inwards the use of flexible metal pipes to connect the
59. surfaces 15 terminated after several Check that the power supply cable is connected correctly heating processes The bipolar switch in the rear right part must be positioned o This appliance must not be used to burn waste on 1 gt DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE FILLING PHASE IN THE EVENT OF CONTINUOUS NO IGNITION CONTACT AN AUTHORISED TECHNICIAN DO NOT USE ANY INFLAMMABLE LIQUIDS FOR IGNITION Extraflame THE REMOTE CONTROL ENGLISH All that can normally be implemented through the LCD can be adjusted using the remote control The table below provides a detailed description of the various functions Pressing the key for three seconds the stove will switch on or off Pressing the key will increase the operating power Pressing the key will decrease the operating power The set temperature can be increased by pressing this key The set temperature can be decreased by pressing this key Pressing the key once will enable or disable the chrono The delayed switch off can be set by pressing this key For example if the stove is set to switch off in an hour it shall switch off automatically once the set time elapses displaying the countdown every minute for delayed automatic shutdown This key allows to access the user and technical menu the technical menu is reserved for assistance The set temperature can be increased by pressing
60. tial status 0 0 e SEASON In SUMMER mode the room thermostats relative to the heating system are satisfied In addition to the areas the request by a puffer is inhibited the boiler will only operate to satisfy the DHW request In WINTER mode all requests are instead considered CONTROLS PROCEDURE Press key 6 and SET POWER will appear Press key 2 until SET ADJUSTMENTS is displayed Confirm using key 6 Press key 2 until SEASON is displayed Set SUMMER or WINTER with keys 4 5 Press key 6 to confirm press key 1 several times to exit the menu 0 ENABLE BOILER TIMER CANNOT BE ACTIVATED N B Diadema ACS features an instantaneous heat exchanger for the production of domestic hot water and it is not possible to set the Boiler timer BOILER SETTING The menu allows to set the boiler in the BIOMASS mode the boiler functions exclusively without controlling other auxiliary boilers present in the system BIOMASS AUX where the boiler can also manage an auxiliary boiler or AUX where the pellet boiler is excluded from functioning to leave just the auxiliary in operation CONTROLS PROCEDURE Press key 6 and SET POWER will appear Press key 2 until SET TEMPERATURE is displayed Confirm using key 6 Press key 2 until BOILER SETTING is displayed Press keys 4 5 to configure the setting Press key 6 to confirm press key 1 several times to exit the menu USER MENU SET CLOCK see
61. tsds eassstonsensnuetssseedsusstnscdesesonsnsecsneserbesssbvedebavssbetvennasssebesdesossetasoss 23 COMMISSIONING SETTINGS ve ADJUSTING TIME DAY MONTHAND YEAR sissssctscasscccvscssssvescsesecseveetisendesensvesetsqsctaceosbisrecveetsaseadtvestbaseeeesensndudcesssintnssetonecndbveonessitedestdssgtavesesessioetsecvuiesiss 24 ADJUSTING LANGUAGE a eroi 24 OPERATION AND LOGIC MENU STRUCTURE SET POWER ici ERRE RR A AAA Ria ENABLE BOILER TIMER BOILER SEM TING scssccssnsssssssssccsssnassocconsssasstevusesnossesedvestonsessasocesscasvsssessosssveeseasosssbesssassnsseesivesseseesconsbesvesdetessrbisscdbssanossoctsdstes ceGehocarasscesbebetasvesdvacesssvotsssisdivsens USER nese nese nesennicanesanesenniennese nesennea nese nese nenna nina nesa ninna nen neein nese nicnanione SET CLOCK CHRONO shiista PROGRAMMING EXAMPLE 33 ADJUSTING LANGUAGE sinistri riciclare raro 34 BOILER CHRONO 35 OTEERIEUNC TION SE MEERE 35 S CHA REM ARR o 35 FIRS I LOAD RU 35 CLEANING UNDER USER S EELEE o kirece coeso coe 36 ROUTINE MAINTENANCE TA E e ee R oeoo ceceo coce eo AREE coeso coe AREE o cocoecoesecoecocoecocoecoecee ERREEN gt EELEE he cocote 37 A a O o OR EEEE A u 39 LE
62. uExtraflame Riscaldamento a Pellet DIADEMA ACS IDRO USER MANUAL ENGLISH INGLESE Extraflame Extraflame ENGLISH We thank you for having chosen our company our product is a great heating solution developed from the most advanced technology with top guality machining and modern design aimed at making you enjoy the fantastic sensation that the heat of a flame gives in complete safety Extraflame S p A VAIL PA SAFETY ROUTINE MAINTENANCE cccssrrreresee rice zesesesene see nese nnene nese zena nese ezine nese ne nea nenesnesnneene nin nesennsenecnneseo HYDRAULIC 5 nese nese ninna nina nese nese enne nese ee ne nese enine nese ninna nen naso nese nicne nio nesanecnnzenneseo INSTALLATION AND SAFETY DEVICES cssccssssssevsccassostsssosssssonssossosedeansectasanrsnessassientseecieessnassecbvesstescenubsensssosnases onsvansvecesbssstsssseteclessbscrbostatbesbivesensbessesbssests cte SAFETY DEVICES FOR CLOSED VESSEL SYSTEM DISTANCES OF SAFETY DEVICES ACCORDING TO THE STANDARD 6 TYPE OF 5 CLOSED VESSEL SYSTEM AUTOMATIC THERMOSTATIC MIXER VALVE MANDATORY HYDRAULIC PLANT BA
63. ured with top quality materials and with manufacturing techniques which guarantee total efficiency If during normal use of the product defective or badly working particulars should be detected the replacement of such particulars will be free of charge ex dealer who made the sale TERRITORIAL EXTENSION OF THE WARRANTY Italian territory VALIDITY THE WARRANTY IS CONSIDERED VALID ON THE CONDITION THAT The purchaser sends the attached coupon within 8 days from the purchase date filled in in its every part The purchase date must be validated by the possession of a valid fiscal document issued by the dealer The appliance is installed in compliance with the Standards in force on this subject the prescriptions contained in the provided manual and by professionally qualified staff The appliance is used as prescribed in the instructions manual provided with all products The warranty certificate has been filled in and signed by the customer validated by the dealer The warranty document filled in and accompanied by the purchase fiscal document issued by the dealer must be kept and shown to staff of the EXTRAFLAME S p A Technical After sales Service in the event of intervention THE WARRANTY IS NOT CONSIDERED VALID IN THE FOLLOWING CASES The warranty conditions described above have not been respected Installation has not been performed with respect to the Standards in force regarding the provisions described in the manual book pro
64. vided with the appliance Negligence of the customer due to lack of or incorrect maintenance of the product Presence of electric and or hydraulic plants that do not comply with the standards in force Damages deriving from atmospheric chemical electro chemical agents improper use of the product modifications and tampering with the product inefficacy and or unsuitability of the flue and or other causes not deriving from the manufacture ofthe product Combustion of materials not compliant with the types and quantities indicated in the manual book supplied All damages caused by transport It is therefore recommended to carefully check the goods on receipt immediately informing the dealer of any damage making a note on the transport document and on the carrier s copy EXTRAFLAME S p A is not liable for any damage that can directly or indirectly affect persons objects and pets as a consequence of failure to comply with the prescriptions indicated in this manual book ALL PARTICULARS SUBJECT TO NORMAL WEAR ARE NOT COVERED BY WARRANTY This category includes The gaskets all ceramic or toughened glass coverings and cast iron or Ironker grids the painted chrome or gold plated details the majolica the handles and the electric cables QExtraflame ENGLISH Colour variations crackles and slight size differences of the majolica parts are not a reason for claims as they are natural features of the materials themselves Pa
65. ws setting SUMMER or WINTER operation In the SUMMER mode the room thermostats relating to the heating system and the puffer are always satisfied the thermo stove works to satisfy the DHW In WINTER mode all requests are considered DHW heating system and puffer DHW DHW is controlled via the integrated instantaneous DHW exchanger PH11 OFF and always has priority over all other requests HEATING The activation of the outputs relating to heating is affected by the operating modes Summer Winter and by the presence or absence of the puffer With the puffer deactivated the outputs are activated when there is a request and the temperature of the water in the boiler is hot enough With the puffer activated the outputs are activated when there is a request and the temperature of the puffer is hot enough One can enable the 4th Heating Zone By setting parameter PH13 on 1 To activate the puffer contact the dealer Default setting PH13 0 disabled PUFFER With the puffer active set PH12 ON the thermo stove operates to satisfy the requests of the puffer and DHW always priority Default setting PH12 OFF disabled To activate the puffer contact the dealer ATTENTION THE PRODUCTION OF DHW IS ALREADY INTEGRATED IN THE MACHINE THE PRODUCTION OF DOMESTIC HOT WATER IS ONLY ENSURED WHEN THE STOVE IS SWITCHED ON OPERATING OTHERWISE ONE MUST WAIT FOR THE STOVE TO SWITCH ON IN THE EVENT THE OPTIONAL INPUTS ARE USED PUFF
66. y 1 for three seconds When the operation has been performed the appliance automatically enters the switch off phase blocking the supply of pellets The flue gas exhaust motor will remain on until the stove temperature has dropped below the factory parameters RE IGNITION The stove can only be re ignited automatically or manually when the cooling cycle conditions and the preset timer have been satisfied NO IGNITION FIRST IGNITION COULD EVEN FAIL AS THE AUGER IS EMPTY AND IS NOT ALWAYS ABLE TO LOAD THE BURN POT WITH THE REQUIRED AMOUNT OF PELLETS ON TIME TO REGULARLY START THE FLAME IF THE PROBLEM OCCURS AFTER ONLY A FEW MONTHS WORKING CHECK THAT ROUTINE CLEANING STATED IN THE STOVE BOOKLET HAS BEEN CARRIED OUT CORRECTLY Extraflame ENGLISH INSTANT DOMESTIC HOT WATER PRODUCTION KIT The thermo stove is equipped with a kit for the production of domestic hot water consisting of a plate heat exchanger a motorised diverter valve and a flow switch Domestic water production 11 min At 30 C In absence of a request for domestic water the heat generator heats the system water In the event of a request for domestic water the power of the generator is all used to produce domestic hot water heat is not supplied to the heating system In order to ensure proper operation in the domestic mode the thermo stove must switched on in steady state conditions and in operation If the heat generator is in the H OFF T OFF

DIADEMA ACS IDRO USER MANUAL - La Nordica

Contents

Download Pdf Manuals

Related Search

Related Contents