DiiVA DIY Field Termination User Manual
Contents
1. LUA Website www luxielectronics com Phone 1 949 654 2047 A Electronics Email xlu luxielectronics com Address Irvine CA USA DIIVA DIY Field Termination User Manual For terminating Cat6 cables with DiiVA connectors Thank you for purchasing the Luxi Electronics patent pending DiiVA DIY Do It Yourself field termination products If you are an experienced installer with the DIY products you can just print out this first page with wire color coding picture for your reference If you are new to the DIY products please make sure you read through all the pages before performing the termination Wire color coding Please note that the Luxi DiiVA DIY products DO NOT follow the industry TIA 568A or B pin configurations Please follow the Luxi pin configurations show below 1 2 3 4 5 6 7 8 DiiVA DIY user manual Revision 0 55 Date 1 3 2012 B F LUXr Website www luxielectronics com Phone 1 949 654 2047 Flectronics Email xlu luxielectronics com Address Irvine CA USA Identifying the components First make sure you have all the necessary parts for the field termination B Cat6 Cable Oty JAP Lb wea on pace hbar iy LUXE Tatia Oty COMMS TOR ae e Cider nio EE As shown in the picture above you ll need the Luxi DiiVA DIY connector components 3 piece Luxi connector clamshell 2 piece standard Cat6 cables a Luxi hand tool and a blade Be familiar with the component names as2. If you ever need to release the latch turn the thumb nail in the marked direction DiiVA DIY user manual Revision 0 55 Date 1 3 2012 LUXr Website www luxielectronics com Phone 1 949 654 2047 Electronics Email xlu luxielectronics com Address Irvine CA USA 3 3 Place the bottom metal shell onto the top 3 5 Press the metal shells into the top clamshell metal shell line up the 4 notches push together until you hear or feel clicks 3 6 Place the bottom clamshell onto the top one Note if you are using a shielded Cat6 cable be and press them together until you hear or sure to wrap all braids and drain wires around feel clicks the cable jacket under the strain relief tabs 3 4 Use the No 3 dies to crimp the strain relief tabs tightly around the cable jacket 3 7 Congratulations You ve just made a beautiful DiiVA termination Note If you are using a shielded Cat6 cable cut off the excessive braids and drain wires exposing from the strain relief after the crimp DiiVA DIY user manual Revision 0 55 Date 1 3 2012 _ m LUA Website www luxielectronics com Phone 1 949 654 2047 s Electronics Email xlu luxielectronics com Address Irvine CA USA Max cable length The max cable length depends on many factors such as the signal data rate resolution source device signal quality TV sensitivity and the compatibility between them As a rule of thumb this DIY cable typically should work fo
3. r up to 25 m 82 at 1080p signal rate Technical support Please contact your distributor or directly to Luxi Electronics for technical support DiiVA DIY user manual Revision 0 55 Date 1 3 2012
4. show below Connector Core ey Top Metal Shell i Top Clamshell ire Holder Bottom Clamshell DiiVA DIY user manual Revision 0 55 Date 1 3 2012 LUXr Website www luxielectronics com Phone 1 949 654 2047 Electronics Email xlu luxielectronics com Address Irvine CA USA Cs Step 1 wire preparations Step 2 wire threading 1 1 Use a blade to cut around a circle of the 2 1 Carefully thread the wires one by one thru Cat6 cable overall jacket about 4 cm 1 1 2 the wire holder per the color coding on page from the end then remove the jacket 1 the entrance has a lip around the sides 1 2 Cut off the center cross divider from the very 2 2 Important Slide the wire holders as far bottom you can reach inward as they can go for best performance 1 3 Un twist the wires of the 4 twisted pairs DiiVA DIY user manual Revision 0 55 Date 1 3 2012 LUXr Website www luxielectronics com Phone 1 949 654 2047 Electronics Email xlu luxielectronics com Address Irvine CA USA 2 3 Insert the wire holders all the way into the Step 3 final assembling No 1 hole on the hand tool following the 1 r finger he wire hol marked orientation perform a pre crimp 3 1 Use your fingers to press the wire holders into the connector core half way 3 2 Insert the connector core with wire holder all the way into the No 2 hole following the marked orientation perform a crimp 2 4 This tool has a ratchet design
Download Pdf Manuals
Related Search